Scribd
Upload
3K views4 pages

Program To Interface GSM Modem With PIC18F4550 Microcontroller

This code interfaces a PIC18F4550 microcontroller with a GSM modem to provide 4 functions: 1. Test an AT command to check communication with the modem 2. Get the IMEI number of the GSM modem 3. Make a call to a mobile number 4. Send a text message to a mobile number It initializes ports and the LCD, reads button inputs to select an option, sends appropriate commands to the modem and displays responses on the LCD.

Uploaded by

Arun Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3K views4 pages

Program To Interface GSM Modem With PIC18F4550 Microcontroller

This code interfaces a PIC18F4550 microcontroller with a GSM modem to provide 4 functions: 1. Test an AT command to check communication with the modem 2. Get the IMEI number of the GSM modem 3. Make a call to a mobile number 4. Send a text message to a mobile number It initializes ports and the LCD, reads button inputs to select an option, sends appropriate commands to the modem and displays responses on the LCD.

Uploaded by

Arun Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

//Program to interface GSM Modem with PIC18F4550 Microcontroller //This code takes four choices as four inputs

//Choice //Choice //Choice //Choice #define #define #define #define #define #define #define 1 2 3 4 : : : : Test the simple AT Command. Find out the IMEI number of the GSM Modem. Connect a call to a GSM mobile number. Send a text message to a mobile number.

FREQ 12000000 baud 9600 spbrg_value (((FREQ/64)/baud)-1) rs LATA.F0 rw LATA.F1 en LATA.F2 lcdport LATB

void tx_data(unsigned char); unsigned char rx_data(); void lcd_ini(); void lcdcmd(unsigned char); void lcddata(unsigned char); void gsm_cmd(unsigned char *); void output(void); unsigned char value=0; int i=0,j,k,temp,flag,choice; unsigned char *starting_text="Enter choice="; unsigned char *dial_text="Dialing..."; unsigned char *at_cmd="AT"; unsigned char *imei_cmd="AT+GSN"; unsigned char *call_cmd="ATD9xxxxxxxxx;"; // Provide a 10-Digit Mobile Number unsigned char *sms_format="AT+CMGF=1"; unsigned char *sms_write="AT+CMGS=\"xxxxxxxxxx\""; // 10-Digit Mobile Number unsigned char *sms="Hello"; unsigned char *sms_report="SMS Sent..."; unsigned char sms_terminate=0x1A; unsigned char enter=0x0D; unsigned char *data; void main() { TRISB=0; LATB=0; TRISA=0; LATA=0; TRISD=0xFF; LATD=0; SPBRG=spbrg_value; RCSTA.SPEN=1; pins) TXSTA.TXEN=1; RCSTA.CREN=1; PIE1.RCIE=1; INTCON.GIE=1; INTCON.PEIE=1; lcd_ini(); while(1) { k=0;

// Set Port B as output port

// Fill SPBRG register to set the baud rate // To activate serial port (Tx and Rx // // // // // Activate Transmissiom Activate Reception Enable Reception interrupt Enable Global interrupt Enable Peripheral interrupt

lcdcmd(0x80); while(starting_text[k]!='\0') { lcddata(starting_text[k]); k++; } //Check inputs //Choice 1 if(PORTD.F0) { gsm_cmd(at_cmd); output(); Delay_ms(1000); } //Choice 2 if(PORTD.F1) { gsm_cmd(imei_cmd); output(); Delay_ms(1000); } //Choice 3 if(PORTD.F2) { gsm_cmd(call_cmd); output(); Delay_ms(1000); } //Choice 4 if(PORTD.F3) { gsm_cmd(sms_format); output(); Delay_ms(1000); gsm_cmd(sms_write); output(); Delay_ms(1000); gsm_cmd(sms); output(); tx_data(0x1A); Delay_ms(1000); } } } void gsm_cmd(unsigned char *string) { i=0;j=0; while(string[i]!='\0') { temp=0;

if(string[i]==0x5C) i++; tx_data(string[i]); i++; while(temp!=1); } temp=0; tx_data(enter); while(temp!=1); } void output(void) { lcdcmd(0x01); i=-1;flag=0; while(i<j) { if(flag>1) { flag=0; Delay_ms(500); lcdcmd(0x01); lcdcmd(0x80); } if(data[i]==0x0A)

// Not to send '\' cahracter // Send by serial communication

// Send ASCII code for 'Enter' key

// To print data on LCD

// This condition is to avoid double Enter

// during execution of a command { flag++; lcdcmd(0xc0); } if(data[i]=='>'||data[i]=='"') // Not to print this character { i++; lcdcmd(0xc0); } if(data[i]!=0x0D&&data[i]!=0x0A&&data[i]!=0x1A) // Condition to print the data // except 'Enter','New line' and 'Submit' { lcddata(data[i]); i++; } else i++; Delay_ms(300); } lcdcmd(0x01); } void tx_data(unsigned char serial_data) { TXREG=serial_data; while(PIR1.TXIF==0); } // Transmit data function

void interrupt() {

data[j]=RCREG; interrupt occurs value=RCREG; j++; temp=1; } void lcd_ini() { lcdcmd(0x38); lcdcmd(0x0C); lcdcmd(0x01); lcdcmd(0x06); lcdcmd(0x80); } void lcdcmd(unsigned char cmdout) { lcdport=cmdout; rs=0; rw=0; en=1; Delay_ms(10); en=0; }

// Store the data into array when Reception

// // // // //

Configure the LCD in 8-bit mode, 2 line and 5x7 font Display On and Cursor Off Clear display screen Increment cursor Set cursor position to 1st line, 1st column

//Send command to lcdport=PORTB

void lcddata(unsigned char dataout) { lcdport=dataout; //Send data to lcdport=PORTB rs=1; rw=0; en=1; Delay_ms(10); en=0; }

You might also like