Orphee Mythic 22 Hematology Analyzer - User Manual

mythic 22
Users Manual
Orphe SA
19, chemin du Champ des Filles - 1228 CH-Plan Les Ouates / SWITZERLAND Tel : +41.(0)22.706.18.40 Fax : +41.(0)22.794.43.91 - Web Site : www.orphee-medical.com
Cod. M22/UM-EN/006
REF : M22/UM/EN/006
REVISIONS
Revision Nb
01 02 03 04 05
Date
16/11/05 27/03/06 25/10/06 03/05/07
Author
HC OM/HC HC/SH HC HC/CM
Software
> V1.0 > V1.0.0-008 > V.1.1.0 > V 2.0.0 > V2.2.0
Comments
Creation Sections 3.4.6 / 4.2 / 5.6.3 / 9.8 modified Sections 3.4.4 / 5.7 / 8.5 / 9.6 / 9.1.1 modified Management of USB key (sections 3.3/5.10/6.2/7.2) Add flags information. (section 8.5.5 / 8.5.6) Modify (QC & CALIBRATION ) Update Hydraulic diagram and tubing list Update of Installation Kit Update of Maintenance Kit Update Hydraulic diagram and tubing list
06
07/12/09
OM
CONTACT ADDRESS MANUFACTURER
M
LOCAL AGENT
Manufactured in France for ORPHEE SA 19, chemin du champ des filles CH-1228 Geneva / Plan-les-Ouates SWITZERLAND Tel : +41 (0) 22 706 1840 Fax : +41 (0) 22 794 4391 http://www.orphee-medical.com
Page 2/99
Copyright Orphe SA. All Rights Reserved.
MYTHIC 22
REF : M22/UM/EN/006
READ THIS BEFORE USING THE EQUIPMENT

WARNING! RISK OF DANGER! Indicates a procedure to be strictly respected in order to avoid any risks for the operator (user) or damages on the instrument or on the quality of results. Indicates that wearing gloves is mandatory before performing the described operation due to risk of contact with materials that may be infectious. Indicates hot temperatures surfaces and risk of burns NOTA Indicates important additional information
DANGER
Misuse of electrical equipment may cause electrocution, burns, fire and other hazards.
Check that the voltage setting matches the supply voltage. Protective earthing is required, plug the MYTHIC 22 into a supply outlet which has an earth connection. Preserve a good access to the supply outlet to be able to unplug the MYTHIC 22 in emergency case. Do not place the power supply adapter in liquid, nor put it where it could fall into liquid. If the power supply adapter becomes wet, unplug it before touching it. Do not use the MYTHIC 22 if it is not working properly, or if it has suffered any damage ( damage to the supply cord or its plug; damaged caused by dropping the power supply adapter). Do not let the power supply adapter or its flexible cord come into contact with surfaces which are too hot to touch. Do not place anything on top of the MYTHIC 22 Do not use the MYTHIC 22 where aerosol sprays are being used, or where oxygen is being administred. Do not use the MYTHIC 22 out of doors Always switch off the MYTHIC 22 and disconnect the power adaptor before dismantling any part. The MYTHIC 22 is an automated hematology analyzer for in vitro diagnostic use in clinical laboratories by an authorized people. - Only human blood or artificial control blood should be run. - Only the reagents mentioned in this manual are permitted to use. - The optimum performances can be only achieved if the cleaning and maintenance procedures are carefully followed. Due to the use of this equipment, all parts and surfaces of the MYTHIC 22 are potentially infective. Wearing rubber gloves is highly recommended and after completion of work, wash hands with disinfectant. Always replace or use parts of the equipment by parts supplied by ORPHEE distributor. Basic safety precautions should always be taken. If the equipment is not u sed according to the manufacturers instructions, the protective by the equipment may be impaired. The treatment of waste and the elimination of a part or the complete instrument must be done in compliance with the local legislation. Any output or input connections (except the printer and the barcode reader supplied by ORPHEE) cannot be done without the ORPHEE representative authorization. Do not open the door located on the right side of the instrument (see section 1.1.3) when an hydraulic cycle is in progress for it would lead to an immediate stop. To re-start, shut the door and run a Control cycle (see section 9.3.1)
KEEP THESE INSTRUCTIONS
MYTHIC 22
Page 3/99
REF : M22/UM/EN/006
This equipment needs special precautions regarding general requirements for safety.
Guidance and manufacturers declaration Electromagnetic emmissions The MYTHIC 22 is intended for use in the electromagnetic environment specified below. The customer or the user of the MYTHIC 22 should assure that it is used in such an environment.
Harmonic emissions
Emmissions test
Compliance level
Class A
IEC 61000-3-2 Voltage fluctuations/flicker emissions IEC 61000-3-3
Complies
The MYTHIC 22 is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Electromagnetic environment - guidance
Guidance and manufacturers declaration Electromagnetic immunity The MYTHIC 22 is intended for use in the electromagnetic environment specified below. The customer or the user of the MYTHIC 22 should assure that it is used in such an environment. Immunity test
Electrostatic discharge (ESD) IEC 61000-4-2
IEC 60601 test level

6 kV contact 8 kV air
Compliance level
Complies
Electromagnetic environment - guidance

Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %.
Electrical fast transient/burst IEC 61000-4-4 Surge IEC 61000-4-5 Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11
2 kV for power supply lines 1 kV for input/output lines
Complies
Mains power quality should be that of a typical commercial or hospital environment.
1 kV differential mode 2 kV common mode <5 % UT (>95 % dip in UT) for 0,5 cycle 40 % UT (60 % dip in UT) for 5 cycles 70 % UT (30 % dip in UT) for 25 cycles <5 % UT (>95 % dip in UT) for 5 sec 3 A/m
Complies
Mains power quality should be that of a typical commercial or hospital environment. Mains power quality should be that of a typical commercial or hospital environment. If the user of the MYTHIC 22 requires continued operation during power mains interruptions, it is recommended that the MYTHIC 22 be powered from an uninterruptible power supply or a battery.
Complies
Power frequency (50/60 Hz) magnetic field IEC 61000-4-8
Complies
Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
Page 4/99
MYTHIC 22
REF : M22/UM/EN/006
Guidance and manufacturers declaration Electromagnetic immunity The MYTHIC 22 is intended for use in the electromagnetic environment specified below. The customer or the user of the MYTHIC 22 should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance
Portable and mobile RF communications equipment should be used no closer to any part of the MYTHIC 22, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance Conducted RF IEC 61000-4-6 Radiated RF IEC 61000-4-3 3 Vrms 150Khz to 80Mhz 3 Vrms 80Mhz to 2,5Ghz 3 Vrms
d = 1,2P
3 Vrms
d = 1,2P 80MHz to 800MHz d = 2,3P 800MHz to 2,5GHz

Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol:
NOTE 1 At 80Mhz and 800MHz, the higher frequency range applies. NOTE 2 Theses guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM an FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should considered. If the measured field strength in the location in which the MYTHIC 22 is used exceeds the applicable RF compliance level above, the MYTHIC 22 should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the MYTHIC 22.
b
Over the frequency range 150KHz to 80MHz, field strengths should be less than 3V/m.
MYTHIC 22
Page 5/99
REF : M22/UM/EN/006
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: How to identify and Resolve Radio/TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4. Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by C2 Diagnostics may cause, harmful interference and void the FCC authorization to operate this equipment.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office or your distributor of this product.
Page 6/99
MYTHIC 22
REF : M22/UM/EN/006
KONFORMITTSERKLRUNG / DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY / DICHIARAZIONE DI CONFORMITA

Name und Adresse der Firma Nom et adresse de lentreprise Nome e indirizzo della ditta Name and address of the firm Wir erklren in alleiniger Verantwortung, dass Nous dclarons sous notre propre responsabilit que Dichiariamo sotto nostra responsabilit che We declare under our sole responsibility that
Orphe S.A. 19 Chemin du Champ des Filles 1228 Plan Les Ouates
das Medizinprodukt fr die In-vitro-Diagnostik le dispositif mdical de diagnostic in vitro il dispositivo medico-diagnostico in vitro the in vitro diagnostic medical device
Mythic 22 Ref. M22OT
mit folgender Klassifizierung nach der Richtlinie ber In-vitro-Diagnostika 98/79/EG avec la classification selon la directive relative aux dispositifs mdicaux de diagnostic in vitro 98/79/CE con la classificazione secondo la direttiva relativa ai dispositivi medico-diagnostici in vitro 98/79/CE classified as follows according to the directive on in vitro diagnostic medical devices 98/79/EC Produkt der Liste A, Anhang II / Dispositif de la liste A, annexe II / Dispositivo dellelenco A, allegato II / Device of List A, Annex II Produkt der Liste B, Anhang II / Dispositif de la liste B, annexe II / Dispositivo dellelenco B, allegato II / Device of List B, Annex II Produkt zur Eigenanwendung, das nicht in Anhang II genannt ist / Dispositif destin lautodiagnostic non list dans lannexe II / Dispositivo per test autodiagnostico non elencato nellallegato II / Device for self-testing not listed in Annex II Sonstiges Produkt / Autre dispositif / Altro dispostivo / Other device
allen Anforderungen der Richtlinie ber In-vitro-Diagnostika 98/79/EG entspricht, die anwendbar sind. remplit toutes les exigences de la directive relative aux dispositifs mdicaux de diagnostic in vitro 98/79/CE qui le concernent. soddisfa tutte le disposizioni della direttiva relativa ai dispositivi medico-diagnostici in vitro 98/79/CE che lo riguardano. meets all the provisions of the directive on in vitro diagnostic medical devices 98/79/EC which apply to it.
MYTHIC 22
Page 7/99
REF : M22/UM/EN/006
Angewandte Gemeinsame Technische Spezifikationen, harmonisierte Normen, nationale Normen oder andere normative Dokumente Spcifications techniques communes, normes harmonises, normes nationales et autres documents normatifs appliqus Specifiche tecniche comuni, norme armonizzate o nazionali applicate, altri documenti normativi applicati Applied common technical specifications, harmonised standards, national standards or other normative documents Konformittsbewertungsverfahren Procdure dvaluation de la conformit Procedimentodi valutazionedellaconformit Conformity assessment procedure Konformittsbewertungsstelle (falls beigezogen) Organe respons. de l'valuat.de la conformit(si consult) Organo incaric. della valutaz. della conform. (se consultato) Notified Body (if consulted) Ort, Datum / Lieu, date / Luogo, data / Place, date Genve le 06 Juin 2008
IEC 60601-1-2 (2001) EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 (95) A1 (98) A2 (01) EN 61000-4-3 (02) EN 61000-4-4 (95) A1(01) EN 61000-4-5 A1 (01) EN 61000-4-6 (96) A1 (01) EN 61000-4-11 (94) A1 (01) EN 55011 Class B EN 55022 Class B IEC 61010-1 (2001) IEC 61010-2-081 (2001) IEC 61010-2-101 (2002)
N/A
Name und Funktion / Nom et fonction /Nome e funzione / Name and function
Philippe Daire RA & QA
Page 8/99
MYTHIC 22
REF : M22/UM/EN/006
TABLE OF CONTENTS
READ THIS BEFORE USING THE EQUIPMENT.......................................................................... 3 1. INSTALLATION ....................................................................................................... 12 1.1 UNPACKING ................................................................................................................................................................................................ 12
1.1.1 Introduction ............................................................................................................................................................................................ 12 1.1.2 Unpacking Procedure ............................................................................................................................................................................. 12 1.1.3 Visual checking........................................................................................................................................................................................ 13 1.2.1 Installation place.................................................................................................................................................................................... 13 1.2.2 Installation environment ...................................................................................................................................................................... 13 1.3.1 Power supply block ................................................................................................................................................................................. 14
1.2 INSTALLATION CONSTRAINTS ............................................................................................................................................................... 13 1.3 ELECTRICAL CONNECTIONS ..................................................................................................................................................................... 14 1.4 PRINTER CONNECTION ............................................................................................................................................................................. 14 1.5 CONNECTION, CHANGE AND PRIMING REAGENTS ................................................................................................................................. 15 1.6 TRANSPORTATION AND STORAGE .......................................................................................................................................................... 18 2. GENERAL OVERVIEW ................................................................................................. 19 2.1 GENERALITIES.......................................................................................................................................................................................... 19 2.2 OVERVIEW ............................................................................................................................................................................................... 20 2.3 MAIN PART DESCRIPTION ...................................................................................................................................................................... 20
1.5.1 Connection ............................................................................................................................................................................................... 15 1.5.2 Priming ..................................................................................................................................................................................................... 16
2.3.1 Display / Keyboard ................................................................................................................................................................................ 20 2.3.2 Dilution hydraulic part ......................................................................................................................................................................... 22 2.3.3 Mono electronic board ......................................................................................................................................................................... 23 2.3.4 Power Supply Block ............................................................................................................................................................................... 23 2.3.5 Reagent tray .......................................................................................................................................................................................... 24
3. INSTRUMENT SET UP ................................................................................................ 25 3.1 USERS IDENTIFICATION ...................................................................................................................................................................... 25 3.2 SYSTEM STATUS ..................................................................................................................................................................................... 26 3.3 SET UP ..................................................................................................................................................................................................... 27 3.4 ADVANCED SET-UP.................................................................................................................................................................................. 28
3.1.1 Start Up ................................................................................................................................................................................................... 25 3.1.2 In process ............................................................................................................................................................................................... 25
3.4.1 Printer set up : ....................................................................................................................................................................................... 28 3.4.2 Communication: ...................................................................................................................................................................................... 28 3.4.3 Analysis options:.................................................................................................................................................................................... 29 3.4.4 Lab. parameters: ................................................................................................................................................................................... 29 3.4.5 Calibration factor: ................................................................................................................................................................................ 33 3.4.6 Other Setting:....................................................................................................................................................................................... 33 3.4.7 Storage options: .................................................................................................................................................................................... 33 3.4.8 Version release:..................................................................................................................................................................................... 34
4. SPECIFICATIONS ..................................................................................................... 35 4.1 ANALYTICAL SPECIFICATIONS .............................................................................................................................................................. 35 4.2 PHYSICAL SPECIFICATIONS .................................................................................................................................................................. 37 4.3 REAGENTS SPECIFICATIONS ................................................................................................................................................................ 39
4.3.1 Diluent...................................................................................................................................................................................................... 39 4.3.2 Lytic reagent OnlyOne...................................................................................................................................................................... 40 4.3.3 Cleaning solution .................................................................................................................................................................................... 41 4.4.1 Recommendations .................................................................................................................................................................................. 42 4.4.2 Interferences........................................................................................................................................................................................ 42
4.4 ANALYTICAL LIMITATIONS ................................................................................................................................................................... 42
MYTHIC 22
Page 9/99
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS ................................................................................................... 47 5.1 VERIFICATIONS BEFORE STARTING ...................................................................................................................................................... 47 5.2 START UP ................................................................................................................................................................................................. 47 5.3 REAGENT REPLACEMENT ......................................................................................................................................................................... 48 5.4 START UP RINSING ................................................................................................................................................................................. 49 5.5 PREPARATIONS BEFORE ANALYSIS ....................................................................................................................................................... 49 5.6 ANALYSIS ............................................................................................................................................................................................... 49
5.6.1 Introduction ........................................................................................................................................................................................... 49 5.6.2 Sample Identification .......................................................................................................................................................................... 50 5.6.3 Sample run .............................................................................................................................................................................................. 51
5.7 RESULTS .................................................................................................................................................................................................. 52 5.8 PRINTING ................................................................................................................................................................................................ 54 5.9 LOGS ........................................................................................................................................................................................................ 56 5.10 ARCHIVE ................................................................................................................................................................................................ 56 5.11 STAND BY AND SHUT DOWN................................................................................................................................................................. 59 6. QUALITY CONTROL .................................................................................................. 60 6.1 INTRODUCTION ....................................................................................................................................................................................... 60 6.2 QC ........................................................................................................................................................................................................... 60
5.8.1 Model report (A4) external printer ............................................................................................................................................... 54 5.8.2 Model report Thermal printer ........................................................................................................................................................ 55
5.10.1 Results ................................................................................................................................................................................................... 57 5.10.2 View ........................................................................................................................................................................................................ 58
6.2.1 Change ...................................................................................................................................................................................................... 61 6.2.2 Run control blood .................................................................................................................................................................................. 62 6.2.3 Levey-Jennings graph .......................................................................................................................................................................... 63 6.2.4 Restore.................................................................................................................................................................................................... 63
6.3 REPEATABILITY ....................................................................................................................................................................................... 63 7. CALIBRATION ......................................................................................................... 65 7.1 RESULTS ................................................................................................................................................................................................... 66 7.2 TARGET VALUE MODIFICATIONS ........................................................................................................................................................... 67 8. TECHNOLOGY.......................................................................................................... 69 8.1 DETECTION PRINCIPLE ............................................................................................................................................................................ 69
7.1.1 Calibration blood analysis ..................................................................................................................................................................... 66 7.1.2 Calibration ............................................................................................................................................................................................... 67
8.1.1 WBC, RBC, PLT Counting ....................................................................................................................................................................... 69 8.1.2 Five part diff measurement ................................................................................................................................................................ 70 8.1.3 Hemoglobin measurement .................................................................................................................................................................... 71
8.2 LEUCOCYTE ANALYSIS ............................................................................................................................................................................. 71 8.3 ERYTHROCYTE ANALYSIS ....................................................................................................................................................................... 72 8.4 ANALYSIS OF PLATELETS ....................................................................................................................................................................... 73 8.5 FLAGS ...................................................................................................................................................................................................... 73
8.5.1 General Flags .......................................................................................................................................................................................... 73 8.5.2 Instrument Flags .................................................................................................................................................................................. 74 8.5.3 Leucocytes Flags ................................................................................................................................................................................... 75 8.5.3 Erythrocyte and HGB Flags ................................................................................................................................................................ 76 8.5.4 Platelet Flags ......................................................................................................................................................................................... 76 8.5.5 QC Flags.................................................................................................................................................................................................. 76 8.5.6 STARTUP Flags ..................................................................................................................................................................................... 76 8.6.1 Sampling module..................................................................................................................................................................................... 77 8.6.2 Counting bath module ........................................................................................................................................................................... 77 8.6.3 Syringes module .................................................................................................................................................................................... 77 8.6.4 Optical manifold .................................................................................................................................................................................... 77 8.6.5 Optical bench ......................................................................................................................................................................................... 78 8.8.1 Windows .................................................................................................................................................................................................. 78 8.8.2 Menu tree ............................................................................................................................................................................................... 78
8.6 HYDRAULIC DESCRIPTION...................................................................................................................................................................... 77
8.8 SOFTWARE .............................................................................................................................................................................................. 78 9. SERVICE ............................................................................................................... 80 9.1 MAINTENANCE ........................................................................................................................................................................................ 80
9.1.1 Maintenance table .................................................................................................................................................................................. 80 9.1.2 Concentrate cleaning ............................................................................................................................................................................ 81
Page 10/99
MYTHIC 22
REF : M22/UM/EN/006
9.1.3 Piston greasing ....................................................................................................................................................................................... 82
9.2 HYDRAULIC CYCLES ................................................................................................................................................................................. 83 9.3 MECHANICS............................................................................................................................................................................................. 84 9.4 REPAIRING............................................................................................................................................................................................... 85
9.4.1 Emergency stop...................................................................................................................................................................................... 85 9.4.2 Needle or o-ring replacement ............................................................................................................................................................ 86 9.4.3 Baths dismantling .................................................................................................................................................................................. 88 9.4.4 Baths o-ring replacement .................................................................................................................................................................... 91 9.4.5 Aperture block replacement ............................................................................................................................................................... 91 9.5.1 Analytical problems ............................................................................................................................................................................... 92 9.5.2 Other problems ..................................................................................................................................................................................... 93
9.5 TROUBLESHOOTING ............................................................................................................................................................................... 92 9.6 TROUBLESHOOTING MESSAGE .............................................................................................................................................................. 93 9.7 LOGS ERRORS .......................................................................................................................................................................................... 97 9.8 HYDRAULIC DIAGRAM ............................................................................................................................................................................. 98
MYTHIC 22
Page 11/99
1. INSTALLATION
REF : M22/UM/EN/006
1. INSTALLATION
1.1 UNPACKING 1.1.1 Introduction
The MYTHIC 22 is an automated hematology analyzer for in vitro diagnostic use in clinical laboratories by an authorized people. - Only human blood or artificial control blood should be run. - Only the reagents mentioned in this manual are permitted to use. - The optimum performances can be only achieved if the cleaning and maintenance procedures are carefully followed. If the MYTHIC 22 has been stored at a temperature less than 10C it must be left at room temperature during 24 hours. It must be calibrated at each displacement and installation (See section 7).
1.1.2 Unpacking Procedure

Before unpacking the instrument, we recommend to check the box of the instrument and notify any damage to the carrier. - Open the box on the top, remove the starter kit. - Remove the MYTHIC 22 from the box. Starter kit contents:
INSTALLATION KIT QTY 1 1 1 1 1 1 1 1 Tubing DILUENT Tubing WASTE 150W switching adapter European Power line cord MYTHIC 22 User manual MYTHIC 22 Installation Report MYTHIC 22 Quality Control Certificate Screwdriver Slot 1/4" MAINTENANCE KIT QTY 1 1 1 1 1 1 5 1 1 1 1 Designation Tygon tubing L=500mm 1.02mm Tygon tubing L=500mm 1.3mm Tygon tubing L=1000mm 1.52x3.2mm Tygon tubing L=500mm 2.06x4mm Tubing 10 Tubing 50 Cables Ties Rinsing Head O-ring Silicon grease (3gr) Short Arm TORX T10 Tool Short Arm TORX T20 Tool Designation
Page 12/99
MYTHIC 22
REF : M22/UM/EN/006
1. INSTALLATION
1.1.3 Visual checking

Open the door on the right side with the key provided in the kit.
To be checked : 1- Counting chambers perfectly locked in their manifold locations. 2- Needles dismountable system located in the rocker. 3- Rocker in front position at the maximum course.
3 2
1
HAZARDOUS MOVING PARTS, BEWARE TO STAY AWAY FROM THESE PARTS WHEN THE MACHINE IS SWITCH ON.
1.2 INSTALLATION CONSTRAINTS 1.2.1 Installation place

To ensure that the MYTHIC 22 fulfills its function, place the instrument on a table which supports the weight of the instrument, printer and reagents (around 40 Kg). Leave a space of 10 cm in the rear of the instrument to ensure a well-ventilated place. Avoid a place that can be exposed to direct sunlight.
1.2.2 Installation environment

a) Indoor use; b) Altitude up to 2 000 m; c) Temperature 18 C to 34 C; d) Maximum relative humidity 80 % for temperatures up to 31 C decreasing linearly to 50 % relative humidity at 40 C; e) MAINS supply voltage fluctuations up to 10 % of the nominal voltage; f) Transient over voltages typically present on the MAINS supply. g) Rated pollution degree II.
MYTHIC 22
Page 13/99
1. INSTALLATION
REF : M22/UM/EN/006
Please contact Orphes representative if you want to use the instrument in special conditions (height higher than 2000 m or special power supply conditions).
1.3 ELECTRICAL CONNECTIONS

All the connectors are in the rear of the MYTHIC 22 CONNECTION : - 2 USB ports (section 3.4.7) : - Ethernet connection (TCP/IP) : SYMBOL :
- External barcode reader (RS232C) : - Host connection (RS232C) :
- Printer connection (Centronics) :
- Power supply cord connection :
- Equipotentiality :
Any output or input connections (except the printer and the bar code reader supplied by ORPHEE) cannot be done without the ORPHEE representative authorization.
1.3.1 Power supply block

MYTHIC 22 must be connected to the power with the power supply block provided with the starter kit. Choose a well-ventilated place for the block and be sure to connect this power supply in a socket-outlet with a correct earth connection. The power supply block must be placed at the rear of the MYTHIC 22 and, if possible in an upper position to avoid the contact with any liquid. To disconnect electrically the MYTHIC 22, remove the power supply plug from the main circuit. - In the case of replacement of the main power wire supplied with the MYTHIC 22 the new one must comply with the local regulation (31.5mm cable and 250V 10A plug). - The MYTHIC 22 has been certified with the power supply box provided with the machine. The use of another external power supply box is not guaranteed. Please contact your Orphes representative.
1.4 PRINTER CONNECTION

Connect the printer cable in conformity with the printer users manual. Use the parallel rear plug of the MYTHIC 22 ( cable. Select the printer driver (section 3.3). ) or the USB plug ( ) to connect the printer
Page 14/99
MYTHIC 22
REF : M22/UM/EN/006
1. INSTALLATION
1.5 CONNECTION, CHANGE AND PRIMING REAGENTS

MYTHIC 22 works with the reagents described in section 4.3. Some commercial reagents can also be used. Please contact your Orphes represent ative.
1.5.1 Connection
Lysis reagent and cleaning solution:
Before handling the reagents, read carefully their specifications described in section 4.3. - Remove the door on the left side of the instrument. - Put the reagent bottles in the dedicated location. - Remove the caps of the bottles - Tighten the red caps on the Lyse bottle (red sticker) and the blue one on the cleaning solution bottle (blue sticker).
Diluent and waste: - Connect the diluent tube (male connector) on the outlet on the bottom and tighten the cap on the diluent container. - To use a 20 liter diluent container adds the tubing straw adaptor supplied with the installation kit. - Connect the waste tube (female connector) on the outlet on the top and tighten the cap on an empty container. Do not modify the type and the length of the diluent and waste tubes. The diluent must be placed at the same level as the MYTHIC 22.
Waste Diluent
It is mandatory to collect the waste in a container and treat it in compliance with your local legislation.
MYTHIC 22
Page 15/99
1. INSTALLATION
1.5.2 Priming
REF : M22/UM/EN/006
When first starting the MYTHIC 22, it is necessary to perform a complete prime of the fluidic circuit. Before starting, be sure that all the reagent and waste tubes are properly connected. The reagents must be stored 24 hours minimum at room temperature before use.
Priming procedure :
Switch on:
- Connect the power supply block. - Press the ON/OFF button. - The cycle LED green. turns red. No cycle can be performed before it turns
- The information window could stay up to 3 mn to enable the update of all the files.
Login:
- The operators identification display appears. - Enter the users identification, the password (see section 3.1) and press to validate. - AUTONOMY (run) indicates the number of samples (runs) you can perform (calculated with the smaller quantity of reagents). - If this window appears, it means that several results in memory have not been sent before the MYTHIC 22 was switched off. - Press YES to send them immediately, or press LATER to wait at another time or NO if you do not want to send them.
- No USB key is available, connect an USB key then press YES or see section 3.4.7 to change the archive mode.
Page 16/99
MYTHIC 22
REF : M22/UM/EN/006
1. INSTALLATION
System priming:
- The main menu is displayed. - Press on NOTA . To do an emergency stop push shortly on the switch on/off button
- Press priming cycle. - The cycle LED green.
: The MYTHIC 22 performs a complete
turns red. No cycle can be performed before it turns
- AUTONOMY (run) indicates the number of samples (runs. - To prime or to know the quantity of reagent press the dedicated button. - Press to visualize the cycle counters.
- To reset the counter with the button please contact your Orphes representative.
MYTHIC 22
Page 17/99
1. INSTALLATION
DILUENT PRIME: - From the MAIN MENU press
REF : M22/UM/EN/006
then
to have access to this screen. - Enter lot number, the expiry date and the container capacity. - Press to validate the new entry or after changing a new container with the same information. - After the replacement a new container or to prime the diluent, press
- A new entry is automatically done in the logs (see section 5.9)
LYSE AND CLEANER PRIME: Proceed as described above for the diluent. WASTE: - Enter only the capacity of the container.
- After replacement of the waste container press to reset to initialize the waste calculation.
MYTHIC 22 IS NOW READY TO WORK.
1.6 TRANSPORTATION AND STORAGE

Storage temperature: -10C to +50C. If the MYTHIC 22 has been stored at a temperature less than 10C it must be left at room temperature during 24 hours. Before transportation outside the laboratory, perform a complete cleaning with a disinfectant in compliance with the local legislation.
Page 18/99
MYTHIC 22
REF : M22/UM/EN/006
2. GENERAL OVERVIEW
2. GENERAL OVERVIEW
2.1 GENERALITIES
MYTHIC 22 is a fully automated analyzer performing hematological analysis on whole blood collected on EDTA K2 or K3 tubes. Sample volume: 15,7 l (inside the needle, the total volume could be upper in function of the blood remaining outside of the needle). Throughput: > 45 samples/hour 22 analysis parameters in DIF mode and 12 parameters in CBC mode:
Leukocyte parameters: WBC White Blood Cells LYM Lymphocytes in % & # (DIF mode only) MON Monocytes in % & # (DIF mode only) NEU Neutrophils in % & # (DIF mode only) EOS Eosinophils in % & # (DIF mode only) BAS Basophiles in % & # (DIF mode only)
Erythrocyte parameters: RBC Red Blood Cells HGB Hemoglobin HCT Hematocrit MCV Mean Corpuscular Volume MCH Mean Corpuscular Hemoglobin MCHC Mean Corpuscular Hemoglobin Concentration RDW Red Blood cells Distribution Width
Thrombocyte parameters: PLT Platelet MPV Mean Platelet Volume PDW* Platelet Distribution Width PCT* Thrombocrit
* For Investigation Use only in the United States of America
MYTHIC 22
Page 19/99
2. GENERAL OVERVIEW
2.2 OVERVIEW
REF : M22/UM/EN/006
MYTHIC 22 consists of 8 main parts: 1. Display / Keyboard. 2. Dilution hydraulic part. 3. Mono electronic board. 4. Reagent tray. 5. Connection. 6. External power supply block. 7. Printer. 8. Barcode reader (option).
2.3 MAIN PART DESCRIPTION 2.3.1 Display / Keyboard
Stand By and ON/OFF button Et Marche/Arrt Numeric keyboard Delete (DEL) Exit (ESCAPE) Cursors Enter (ENTER) Cycle in process Led Touch screen LCD display 380*240
Page 20/99
MYTHIC 22
REF : M22/UM/EN/006
2. GENERAL OVERVIEW
Main Menu description Start Up rinsing and blank control Print, Send, Select Options
Back to previous screen
Direct access to main menu
Date and time. System status (Section 3.2).
Cleaning and standby mode
Calibration (Section 7). Quality Control (Section 6). Patient Archive (Section 5.10). Mythic setting parameters (Section 3). Maintenance and Service Menu Log In and Log Out (Section 3.1).
Reagents replacement (Section 5.3).
Analysis performing (Section 5.5).
Mythic Events Logs (Section 5.9).
MYTHIC 22
Page 21/99
2. GENERAL OVERVIEW
2.3.2 Dilution hydraulic part
REF : M22/UM/EN/006
All the fluidic part is on the right side of the instrument and consists of only five modules: - Sampling module : o Rocker (patent pending): Manages the rise and descent of the needle. - Syringe module (patent pending) consists of one block : o Reagent syringes (Diluent, lysis), sampling and air syringes. o Liquid valve manifold assembly and tubing. - Counting chambers : o WBC and RBC counting chambers and hemoglobin measurement. o Liquid valve manifold assembly and tubing. - Optical Manifold : o Liquid valve manifold assembly and tubing. - Optical bench : o Optical bench (patented) with his flow cell (patented).
Optical bench
Optical manifold
Sampling module
Syringe module
Counting module
Page 22/99
MYTHIC 22
REF : M22/UM/EN/006
2. GENERAL OVERVIEW
2.3.3 Mono electronic board
The mono electronic board is located between the hydraulic part and the reagent tray. The board, driven by a 32-bit processor, manages the following parts: - Sample needle, rocker, syringe block motors. - Display and keyboard. - Connexion mode (RS232, Ethernet, ). - Printer. - Measurement (Counting, hemoglobin measurement). - Data processing. - External barcode reader.
To avoid all deterioration risks, only the service people can touch this electronic board.
2.3.4 Power Supply Block
Switch on/off
MYTHIC 22 is supplied with an external power supply block. - In the case of replacement of the main power wire supplied with the MYTHIC 22 the new one must comply with the local regulation. - The MYTHIC 22 has been certified with the power supply box provided with the machine. - The use of another external power supply box is not guaranteed. Please contact your Orphes representative.
MYTHIC 22
Page 23/99
2. GENERAL OVERVIEW
2.3.5 Reagent tray
REF : M22/UM/EN/006
The reagent tray is dedicated to the OnlyOne lysing reagent and cleaning solution bottles.
Page 24/99
MYTHIC 22
REF : M22/UM/EN/006
3. INSTRUMENT SET UP
3.1 USERS IDENTIFICATION 3.1.1 Start Up
- After the instruments initialization, the identification windo w is displayed. - In the window , the last operators identification appears. - Either the identification is yours, press and enter your password or the identification is not, press to enter your login.
- The window enables to change the language. Press to validate it. - AUTONOMY (run) indicates the number of samples (runs) you can perform (calculated with the smaller quantity of reagents).
- Enter your identification name with the alphabetic keyboard. - Place the cursor in the Password window. - Enter your password for identification. - For the first login, MYTHIC 22 proposes 3 access levels : o User : No password o Biologist : Password by default 1- 2- 3 o Service people - Biologist Password can be modified in section 3.3.6.
3.1.2 In process
- To change operator during the process, press main menu, and then press on - To change identification, proceed as described above (section 3.1.1). to return to the
MYTHIC 22
Page 25/99
REF : M22/UM/EN/006
- If this window appears, it means that several results in memory have not been sent before the MYTHIC 22 was switched off. - Press YES to send them immediately, or press LATER to wait at another time or NO if you do not want to send them.
- No USB key is available, connect an USB key then press YES or see section 3.4.7 to change the archive mode.
3.2 SYSTEM STATUS

- Press on the date and hour window. to have access to the system status
- Different system status information is displayed. - To change the screen luminosity press L, N or H - To return to the MAIN MENU press
Page 26/99
MYTHIC 22
REF : M22/UM/EN/006
3.3 SET UP
- From the MAIN MENU press on - This menu is available for all users. - The DATE & TIME window enables to modify the time and the date - To select the language of the Mythic menu, choose the right one in the Language combo box. number of results per page. : Select the printer or no printing. : Select the paper size depending on the
: Two SID are available; Start day SID enables to select the first SID for each new day. : If you want to select a new SID number (See section 3.4). - Once modifications are done, press either to valid or to exit keeping the previous setting. : Biologist reserved for complete settings.
- Press
to print, save or load from an USB key all the set up.
- To load new printer drivers plug the USB key then press on - Select the printer and its connection mode. - Then press
in the previous screen.
- Press then, the driver is loaded in the MYTHIC 22
- This prompt appears if the release is failed. Check the USB connection or change the USB key or call your Orphes representative.
This prompt appears if the
release is done successfully.
MYTHIC 22
Page 27/99
3.4 ADVANCED SET-UP
REF : M22/UM/EN/006
- This menu is reserved to biologist (see section 3.1). Any modification can affect the quality of the results. We recommend modifying these values only after an Orphes training. - Please refer below for the description of each key.
3.4.1 Printer set up:

- Printer set up menu is intended to present the printing report - To select an option on the report, press on the corresponding case. - To enter a header, press - To exit the menu, either press to save the last modifications. key. to keep the last setting, or
3.4.2 Communication:
- Reserved for technical Service people. - To set up the connection between MYTHIC and Host.
Page 28/99
MYTHIC 22
REF : M22/UM/EN/006
3.4.3 Analysis options:

- OPTIONS box: o ALWAYS ID and ALWAYS PID: To run a sample, user mandatory needs to enter a ID and/or a PID. o RUO: With tag the PCT and PDW parameters are displayed, printed and send. o US MODE: The Research Use Only message is printing below the printing report. o ABSOLUTE DIF: With tag absolute values for sub-populations of leucocytes are displayed. In the other case, percentages are displayed. o QC ALARMS: The message QC_F QC failed appear below the printing report when the QC result is out of tolerance or expired (see section 8.5.5); The message QC_ND QC not done appear below the printing report when it is not run (see section 8.5.5). : Gives a choice of three unit systems: Standard, International System, and mmol. - Barcode Reader box: The reading of the bar code is dedicated to the PID or ID or SID. - BOLD DISPLAY box: display and print in bold-faced type the different choices in this box. Once modifications are done, press either previous setting. to validate your choices or to exit keeping the
3.4.4 Lab. parameters:

- Select the blood type in the combo box press: section 3.4.4.1). to adjust the parameters thresholds (see section 3.4.4.2). to adjust the flags level (see section 3.4.4.3). to adjust the corrections factors (see section 3.4.4.4).NOTA: No correction factors with type STANDARD. - To enter a new blood type, press NOTA: The name of the first type STANDARD cannot be change. - Press printed) to print the blood type set up. allow to print all the blood type set up (about 20 pages are only the blood type in the combo box is printed. then
to adjust the normal and panic limits (see
MYTHIC 22
Page 29/99
REF : M22/UM/EN/006
To rename a blood type press then press to validate or to exit without any modification.
then select it
to accede at the alphabetic keyboard then press
3.4.4.1 Limits:
- This display enables to enter normal and panic limits for every 22 parameters given by the MYTHIC 22 (see section 8). - To validate the new values, press VALID key in the next page (see below).
- Once modifications are done, press without any modification.
to validate or
to exit
Press standard
to return to the parameter setting of the type.
Page 30/99
MYTHIC 22
REF : M22/UM/EN/006
Example of reference values from LABORATOIRE D'HEMATOLOGIE DU C.H.U. D'ANGERS (FRANCE)

First week WBC 103/L (109/L) Neutrophils (10/L) Eosinophils (10/L) Basophils (10/L) Lymphocytes (10/L) Monocytes (10/L) RBC 106/L (1012/L) HGB g/dL HCT % MCV fl MCH pg MCHC g/dL PLT 10/L (109/L) 10,0 to 30,0 6,0 to 26,0 0,2 to 0,85 0 to 0,64 2,0 to 11,0 0,4 to 3,1 5,0 to 6,0 14,5 to 22,5 44 to 58 100 to 120 34 to 38 32 to 36 150 to 400 8 days to 3 months 6,0 to 18,0 1,5 to 8,5 0,2 to 1,2 0 to 0,2 2,0 to 11,0 0,05 to 1,1 3,8 to 4,8 10 to 16 38 to 44 85 to 96 24 to 34 32 to 36 150 to 400 3 months to 3 years 6,0 to 15,0 1,5 to 8,5 0,05 to 0,7 0 to 0,2 4,0 to 10,5 0 to 0,8 3,6 to 5,2 10,5 to 13,5 36 to 44 70 to 86 23 to 31 32 to 36 150 to 400 3 to 6 years 5,0 to 13,0 1,5 to 8,5 0,02 to 0,65 0 to 0,2 2,0 to 8,0 0 to 0,8 4,1 to 5,3 10,5 to 13,5 36 to 44 73 to 89 24 to 30 32 to 36 150 to 400 6 to 15 years 5,0 to 11,0 1,8 to 8,0 0 to 0,6 0 to 0,2 1,5 to 6,5 0 to 0,8 4,0 to 5,4 11,5 to 14,5 37 to 45 77 to 91 24 to 30 32 to 36 150 to 400 Adult 4,0 to 10,0 1,8 to 7,5 0,04 to 0,8 0 to 0,2 1,0 to 4,5 0,2 to 1,0 M : 4,5 to 5,8 F : 3,8 to 5,4 H : 13,5 to 17,5 F : 12,5 to 15,5 M : 40 to 50 F : 37 to 47 82 to 98 > or = 27 32 to 36 150 to 400
3.4.4.2 Thresholds:
- The threshold display enables to modify the detection thresholds located on the WBC scattergram and RBC, PLT curves (see section 8). Threshold modifications can affect the quality of the results or can affect the alarm detection area. We recommend modifying these values only after an Orphes training. - To accede for modification to the scatter gram threshold press to the flags threshold press - Once modifications are done, press without any modification. - Press . to validate or to exit and
to return to the manufacturer parameter setting.
Threshold modifications can affect the quality of the results or can affect the alarm detection area. We recommend to modify these values only after an Orphes training.
- Press
MYTHIC 22
Page 31/99
REF : M22/UM/EN/006
Threshold modifications can affect the quality of the results or can affect the alarm detection area. We recommend to modify these values only after an Orphes training.
- Press
3.4.4.3 Flags level :
- In the Alarm menu, users can modify the sensitivity of the alarms for the different cells: WBC, RBC, PLT and differential (See section 8.5).
to validate or
to exit
- Press type.
to return to the parameter setting of the standard
3.4.4.5 Correction factors:
- In this menu, for each blood type, users can define a correction factor which is multiplied by the calibration factor given by a normal calibration (see section 7).
to validate or
to exit
Page 32/99
MYTHIC 22
REF : M22/UM/EN/006
3.4.5 Calibration factor:

- To accede at this menu press in the ADVANCED SET UP MENU (see section 3.4) - In this menu, the user can modify the calibration factors without any calibration with calibration blood. - A M letter appears on the right of the date of calibration in case of modification. The modification of any of these factors without running a calibration blood could affect the quality of the result.
3.4.6 Other Setting:

- In DELAY box, the user can modify: o Time in minutes to start the automatic shut down. o Time in minutes to buildup the needle. o The setting up of the automatic cleaning and its frequency in number of analysis . o The setting up of the automatic wake up and its daily time - Reagent checking enables the reagent control (see section 1.5.2) - Pressure Checking is accessible for technician only. enables to modify the biologist password. enables to select the date format. - AM/PM mode enables to display the format of time of your choice. - Once modifications are done, press without any modification. to validate or to exit
3.4.7 Storage options:

MYTHIC 22 can save more than the last 1000 patients with results, alarms, distribution curves in the internal memory and until a maximum of 60 000 results in a memory stick (USB key) of 512 Mbit or more. All the capacity until 2 Gbit maximum can be used. Because the technology of the USB key is very different from one to the other, some of them could not work. For more information contact your Orphes representative. - Choose for a FIFO (first in /first out) mode or real time to store the results in the resident memory or in a USB key. - Choose to directly save sample run onto USB key. If USB key is available, result will be store at the end of the sample run.
MYTHIC 22
Page 33/99
REF : M22/UM/EN/006
Press to format USB key. The system will format the USB Key and build specific directories for Mythic management.
- This prompt appears if none USB key is available.
- Press yes if you agree to format the USB key. It is mandatory to format the USB key on the Mythic before to use it. All the information includes in the USB key will be erased.
3.4.8 Version release:

Load a new software version only with the agreement of an Orphes representative
- Press to load a new software version from a USB key. - Choose the right version then, - Press yes only if you are sure to load new version software.
The current software version will be erased definitively.
- This prompt appears to confirm the version loading.
- This prompt appears when the release of the software is failed. - Choose another version or call your Orphes representative.
Page 34/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
4. SPECIFICATIONS
4.1 ANALYTICAL SPECIFICATIONS
Throughput: > 45 samples/hour
Sample Volume: 15,7 l (inside the needle, the total volume could be upper in function of the blood remaining outside of the needle). Measurement Principle: WBC/RBC/PLT: Impedancemetry Five part diff: Optical flow cytometry Hemoglobin: Spectrophotometry at 555 nm Hematocrit: Volume integration
Linearity: Linearity is measured with linearity sample performed four times for each level.
PARAMETERS WBC (103/mm3) RBC (106/mm3) HGB (g/dL) HCT (%) PLT (103/mm3) RANGE 0 to 100 0,1 to 8 0,5 to 24 5 to 70 5 to 2 000 LIMITS (the larger) +/- 0,4 or +/- 4% +/- 0,07 or +/- 3% +/- 0,3 or +/- 2% +/- 2 or +/- 3% +/- 10 or +/- 5%
Reportable range: Within the reportable range, the results are flagged with a D to indicate that it is necessary to re-dilute and re-run the sample.
PARAMETERS WBC (103/mm3) RBC (106/mm3) HCT (%) PLT (103/mm3) REPORTABLE RANGE 100 to 150 8 to 15 70 to 80 2000 to 4 000
Repeatability: Calculated with 20 runs of a fresh whole blood sample performed on a commercial MYTHIC 22.
PARAMETERS WBC LYM MON NEU EOS BAS RBC HGB HCT MCV RDW PLT PMV CV < 2,5% < 5% < 10% < 4% < 10% < 40% < 2% < 1,5% < 2% < 1% < 4% < 5% < 3% RANGE > to 6,0 103/mm3 > to 15 % > to 7 % > to 50 % > to 5% > to 2% > to 4,0 106/mm3 > to 12,0 g/dL > to 40,0 % > to 85 fL > to 14 > to 250 103/mm3 > to 8 fL
Calculated method:
CV = SD X SD = x- (x) N N-1 Copyright Orphe SA. All Rights Reserved. Page 35/99
MYTHIC 22
4. SPECIFICATIONS
REF : M22/UM/EN/006
Carry-Over: For each parameter, we perform 3 runs from a high concentration sample followed by 3 runs without sample. WBC RBC 145 103/mm3 8.40 106/mm3 0.68 0 < 1,0 < 1,0 HGB 20 g/dL 0 < 1,0 PLT 2300 103/mm3 0.04 < 1,0
High concentration value Measured carry-over (%) Maximum carry-over (%)
The percentages of carry-over inter samples is calculated with the following formula: (Low value cycle 1) - (Low value cycle 3) Carry-over = (High value cycle 3) - (Low value cycle 3) 100
Accuracy: Correlation was done with one commercial instrument (HORIBA ABX PENTRA 120 ) and with about 100 normal blood samples (without alarm). PARAMETERS WBC (103/mm3) LYM (%) MON (%) NEU (%) EOS (%) BAS (%) RBC (106/mm3) HGB (g/dL) HCT (%) MCV (fL) RDW (%) MCH (pg) MCHC (g/dL) PLT (103/mm3) MPV (fL) N 127 113 113 113 113 113 127 127 127 127 127 127 127 127 127 R (%) 0,997 0,989 0,935 0,988 0,950 0,187 0,991 0,997 0,984 0,947 0,746 0,963 0,151 0,990 0,890
n.xy x. y Calculated method: r= (n. x-(x))(n. y- (y))
PENTRA 120 is a registered trademark of HORIBA ABX.
Page 36/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
4.2 PHYSICAL SPECIFICATIONS

General: Ambient temperature: from 18 to 34C Relative Humidity: 80% maximum at 32C Storage temperature: -10 to 50C If the MYTHIC 22 has been stored at a temperature less than 10C, it must stay at room temperature during 24 hours before switching it on.
INSTRUMENT: Dimensions: Height: 350 mm (approx.) Width: 250 mm (approx.) Depth: 340 mm (approx.) Weight: 12kg (approx.) 24V 5A DC
Power supply Input:
Electric consumption: During cycle: 75 VA (-30% +10%) Stand By: 20 VA (-30% +10%) Maximum: 110 VA (-30% +10%) Display: TFT Color LCD 240*320 Mode portrait Retro-lighted Barcode reader: C39/ Barcode / 2 interleaved 5 > 500 Files (Demographics, results and histograms) in the internal memory > 60 000 files in a 512 Kbit USB key QC: 6 levels (100 Files per level) RS 232C Ethernet (TCP/IP)
Barcode (option): Memory capacity:
Connection:
MYTHIC 22
Page 37/99
4. SPECIFICATIONS
Reagent Consumption (ml): Software Version > V2.2.0-005
CYCLES Run Sample Rinse All Back flush Control All Reagent Prime Cleaning Bleach Start Up * Shut Down Latex WBC Latex RBC Latex OPT (1) Latex OPT (2) Latex OPT (3) Optical Led Lysis OnlyOne Diluent Cleaner DIF CBC DILUENT 21,0 13,10 11,0 11,0 14.7 39,20 5,7 31.0 -12,7 46,0 49.6 -14.5 7.10 13.00 13.00 13.00 1.00 LYSE 0,96 0,73 ---5,6 6,5 --0,2 1.1 3,2 0,5 1.10 -0.9 0.9 0.9 0.10 CLEANER 0,45 0,45 -0,30 0,50 5,60 --5,6 5.6 0.45 0,45 23.0 0.45 ------
REF : M22/UM/EN/006
* Consumption with one run sample, add one or two run sample consumption if needed.
POWER SUPPLY BLOCK: Dimensions: Height: Width: Depth: Weight: Power supply Input:
55 mm 127 mm 230 mm 1,32Kg 100 to 240VAC (2A/230VAC at maximum load 4A/115VAC at maximum load) 50-60Hz
PRINTER (LX-300+): Dimensions: Height: Width: Depth: Weight: Power supply:
Electric consumption: Paper size: Printer: Speed:
164 mm (approx.) 366 mm (approx.) 275 mm (approx.) 4,4 kg (approx.) Model 120V Model 220-240V 99 to 132Vac 198 to 264Vac 50 to 60 Hz 23W (approx.) Depends on the format chosen in the set up. Impact (9 needles) Up to 300 cps (character per second)
Page 38/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
4.3 REAGENTS SPECIFICATIONS

All the reagents must be stored at room temperature (18C to 25C).
4.3.1 Diluent
ORPHEE code number: HM22-003-10 Opening shelf life: 60 days. Application: The diluent is used to carry out the necessary dilutions for the measurement performed by the MYTHIC 22.(see section 8) Active components: Others components: Solid content: 0,9%. Buffer. Preservative.
Description: Clear and odorless aqueous solution. Storage: At room temperature until the expiry date labeled on the bottle. Precautions: Can cause skin and eyes irritation. Wear a smock, gloves and glasses during manipulation. First emergency care: Inhalation: Breathe fresh air; seek for medical advice in case of persisting symptoms Eyes: Abundantly rinse opened eye during 15 minutes. Skin: not skin irritating. Ingestion: rinse out mouth; seek for medical advice in case of persisting symptoms. Accidental release and disposal measure : Person related safety precautions: Wear protective equipment; keep unprotected persons away environmental protection: Do not allow product to reach sewage system or water bodies cleaning/collecting: Absorb with liquid-binding material (sand diatomite, acid binders, Universal binders saw dust) Comply with local and/or federal disposal legislation If any doubt, call an emergency center.
MYTHIC 22
Page 39/99
4. SPECIFICATIONS
4.3.2 Lytic reagent OnlyOne
ORPHEE code number: HM22-002-1 Opening shelf life: 60 days. Application:
REF : M22/UM/EN/006
OnlyOne Lytic reagent is used as unique leukocyte and hemoglobin reagent to lyse red blood cells, enable cells subpopulations differentiation and counting and quantitatively determine hemoglobin content of blood samples on MYTHIC 22, (see section 8)
Active components: - alkaline salts and buffering means - ionic and non-ionic surfactants mix - Leuko-protective agents - non toxic Hemoglobin chelate - Preservatives Description: A clear pale yellow aqueous solution (with slight characteristic smell) composed of alkaline salts, inorganic buffers, leukoprotective agents, detergents, a non toxic haemoglobin stabilizing chelate, and preservatives NOTA: This reagent does not contains any cyanide, neither formaldehyde, nor azide. Storage: Precautions: At room temperature, until expiry date labeled on the bottle. Can cause skin and eyes irritation. Wear a smock, gloves and glasses during manipulation.
First emergency care: Inhalation: Breathe fresh air; seek for medical advice in case of persisting symptoms Eyes: Abundantly rinse opened eye during 15 minutes. Skin: Abundantly rinse during 15 minutes; seek for medical advice in case of persisting symptoms Ingestion: give large amount of water; seek for medical advice in case of persisting symptoms. Accidental release and disposal measure : Person related safety precautions: Wear protective equipment; keep unprotected persons away environmental protection: Do not allow product to reach sewage system or water bodies cleaning/collecting: Absorb with liquid-binding material (sand diatomite, acid binders, Universal binders saw dust) Comply with local and/or federal disposal legislation If any doubt, call an emergency center.
Page 40/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
4.3.3 Cleaning solution

ORPHEE code number: HM22-001-1 Opening shelf life: 60 days. Application: The cleaning solution is used to carry out the cleaning of the measurement system and hydraulic circuit (see section 8). Enzyme Propylene glycol 2,5-10%: Dangerous component with critical values that require monitoring at the workplace (CAS 55-57-6; EINECS 200-338-0) OES long term value: 474mg/m3 150ppm total 10mg/m3 particulates Violet dye. Clear aqueous solution, violet color, with characteristic smell At room temperature, until expiry date labeled on the bottle. Can cause skin and eyes irritation. Wear on a smock, gloves and glasses during manipulation.
Components:
Description: Storage: Precautions:
First emergency care: Inhalation: Breathe fresh air; seek for medical advice in case of persisting symptoms Eyes: Abundantly rinse opened eye during 15 minutes. Skin: Abundantly rinse during 15 minutes ; seek for medical advice in case of persisting symptoms Ingestion: give large amount of water; seek for medical advice in case of persisting symptoms. Accidental release and disposal measures: Person related safety precautions: Wear protective equipment; keep unprotected persons away environmental protection: Do not allow product to reach sewage system or water bodies cleaning/collecting: Absorb with liquid-binding material (sand diatomite, acid binders, universal binders, saw dust) Comply with local and/or federal disposal legislation If any doubt, call an emergency center.
MYTHIC 22
Page 41/99
4. SPECIFICATIONS
4.4 ANALYTICAL LIMITATIONS 4.4.1 Recommendations
REF : M22/UM/EN/006
MAINTENANCE: Please respect the maintenance procedure and the quality control procedure. Otherwise, results can be affected. GENERALITIES: Some abnormal samples may give incorrect results by automated cell counting methods. The following table shows examples of specific specimens that could cause errors. Each result for a new patient out of lab linearity limits or with an alarm must be checked with a conventional method or checked with blood smear.
4.4.2 Interferences
Parameter Specimen Occurrence Possible Indication of Error on MYTHIC 22 (+) action
Cause : high IgM level may lower RBC and increase

MCV
WBC
Cold Agglutinin
Indication
HL flags (+)
Seek for red cell clumping MCV, HCT, N1 &/or N2 &/or L1 &/or on Smear
Nucleated RBC Erythroblastosis
Indication : NRBC may be detected on the WBC Seek for NRBC on smear.
scattergram with N1 &/or N2 &/or L1 flags
Cause: in some rare instance few erythrocytes may

Unlysed RBC (+)
not be completely lysed. Indication : lyse-resistant RBC may be detected on the WBC scattergram with N1 &/or N2 &/or L1 &/or HL flags
Cause: In association with various pathologies

Cryoglobulins (+)
cryoglobulins cause the WBC, RBC, Plt and Hgb to Warm the specimen up to increase 37C(99F) for 30min and Indication: high level of all above mentioned items re-assay immediately after. in case of myeloma, carcinoma, leukemia and other proliferative disorders, pregnancy
Platelet aggregation
(+)
Indication : aggregates may be detected on the Seek for Platelet

WBC scattergram with N1 &/or N2 &/or L1 flags
aggregates on smear
(+): Instrument count is affected by an increase in the result. (-): Instrument count is affected by a decrease in the result. (?): Instrument count is affected by either an increase or decrease in the result which is sample dependent.
Page 42/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
Parameter LYM (# & %)
Specimen Nucleated RBC Erythroblastosis Platelet aggregation (+) (+)
Occurrence Possible Indication of Error on MYTHIC 22
action
Indication: NRBC may be detected on the WBC Seek for NRBC on smear.
scattergram with N1 &/or N2 &/or L1 &/or HL flags WBC scattergram with N1 &/or N2 &/or L1 flags
Indication: aggregates may be detected on the Seek for Platelet Cause: These lymphocytes are larger than normal
aggregates on smear
MON (# & %)
Large or atypical lymphocytes
(+)
lymphocytes and tend to overlap the MON clump on Seek for Erythroblasts on the scattergram smear Indication: reduced LYM/MON gap with LYM band RL flags
Cause : These few segmented and granulationsSmall Neutrophils (+) lacking Neutrophils tend to overlap the MON clump on the scattergram Indication: reduced NEU/MON gap with NL flags
Cause : Blasts are large and polymorphic immature

Lymphoid & myeloid Blasts (+)
cells that may overlap all normal cells clumps Indication: reduced/absent LYM/MON even Seek for blasts on smear MON/NEU/LYM gap with overlapping population RL &/or NL &/or HL flags
Excessive number of basophils
Cause: in case of basophilia the basophils clump may

(+)
overlap the MON clump on the scattergram Seek for basophils on smear Indication: reduced LYM/MON gap RL &/or HL &/or NL flags
Cause: Immature monocytic line cells proliferate in
Immature monocytes (+)
certain pathologies (multiple myeloma, monocytic leukemia) and generate a band at the right of Seek for immature normal MON clump that causes an inaccurate high monocytes on smear level of monocytes. Indication: : diffuse MON clump with right-end flame population IC &/or L5 &/or NL flags
NEU (# & %)
Excessive number of eosinophils
Cause: The excessive presence of eosinophils

(+)
check the eosinophils clump (eosinophilia) may interfere with NEU counting on the scattergram to Indication: EOS clump is overlapping NEU clump NH eliminate eosinophilia flag
Cause : metamyelocytes, myelocytes, promyelocytes,

Immature granulocytes (+)
blasts or plasma cells are large and polymorphous Seek for immature cells on cells that may overlap NEU clump smear Indication: diffuse spreading out NEU clump NL &/or RL &/or IC &/or L5 flags
MYTHIC 22
Page 43/99
4. SPECIFICATIONS
REF : M22/UM/EN/006
Parameter
Specimen
action
Cause: Toxic or abnormal granules, as much as

EOS (# & %) Granulations modifications (-)
degranulated areas may alter optical properties of Seek for Granulations eosinophils and cause an erroneous EOS counting modifications on smear Indication: diffuse downwards spreading EOS clump overlapping NEU clump, NH Flag
Atypical Neutrophils
Cause: hyper-segmented or giant Neutrophils may

(+)
Seek atypical Neutrophils overlap EOS clump on smear Indication: upwards spreading NEU clump overlapping EOS clump, NH &/or IC &/or L5 Flags
BAS (# & %)
Blasts, immature, atypical cells
Cause: abnormal cells may overlap the basophils

(+)
clump and interfere with the basophil counting Seek for blasts on smear Indication: absence of LYM/MON(NEU) gap with RL &/or NL &/or HL flags
RBC
Cold Agglutinin
(-)
Cause: high IgM level may lower RBC and increase

MCV
Indication: MCV, HCT Cause: in very rare case of severe microcytosis, size
(-)
Seek for red cell clumping on Smear
Severe Microcytosis
of microcytes may fall below the minimum RBC Seek for microcytes on threshold. Smear Indication: RBC, Plt R1 &/or P3 flags
Macrocytosis
(-)
Cause: in case of macrocytosis, size of macrocytes

may overcome the maximum RBC counting zone. Indication : RBC, MCV, R2 flag RBC count. Indication: abnormal MCH and MCHC values and interfere with RBC counting. Indication: RBC, Plt, MPV, P2 flag RBC count. RBC
RBC agglutination
(?)
Cause: agglutinated RBC may cause a low inaccurate
Seek for clumped RBC on Smear
Fragmented RBC
(-)
Cause: RBC fragments (schizocytes) may agglutinate
Seek for schizocytes on Smear
Cause: high level of WBC may cause an erroneous

Leukocytosis (+)
Indication:
very MCHC
high
WBC
Centrifuge the sample and re-assay the re-diluted RBC (>100,000/ L), part.
Page 44/99
MYTHIC 22
REF : M22/UM/EN/006
4. SPECIFICATIONS
Parameter
Specimen
action Centrifuge the sample
HGB
Leukocytosis
(+)
Cause: high level of WBC causes excessive light remove WBC and re-assay
scatter that interferes with Hgb measurement. Indication: very high WBC (>100,000/ L), MCHC
the re-diluted RBC part. Or use reference spectrophotometric method
hyperlipidemia
Cause: in case of high level of lipids in blood will give

(+)
Use reference manual the plasma a milky appearance that causes methods and a plasma blank inaccurate Hgb measurement. to determine Hgb Indication: plasma appearance MCHC,
Abnormal Protein hyperproteinemia, hyperbilirubinemia
Cause: in case of high level (or abnormal) of

(+)
proteins in blood will give the lysed sample a Use reference manual cloudy appearance that causes inaccurate Hgb methods and a plasma blank measurement. to determine Hgb Indication: lysed sample appearance MCHC
HCT
Cold Agglutinin Leukocytosis Abnormal Red Cell Fragility
(-)
Cause: high IgM level may lower RBC and increase

MCV
Indication: MCV, HCT,

(+) Elevation of WBC
Seek for red cell clumping on Smear
Cause: in case of chemotherapy cytotoxic and

(-)
immunosuppressive drugs may increase RBC as well as WBC fragility leading to a low HCT Indication: P1 flag
Spherocytosis
(?)
Cause: in case of Spherocytosis, sphered RBC are

smaller than normal RBC leading to a low HCT Indication: MCV, P2 &/or P3&/or R1 flags
Seek for spherocytes on Smear Seek for clumped RBC on Use reference manual methods to determine the accurate MCV value. Seek for megalocytic platelets on Smear
MCV
RBC agglutination
(?)
Cause: agglutinated RBC may cause an inaccurate Smear

MCV value. Indication: abnormal MCH and MCHC values
Megalocytic Platelets Leukocytosis
(-)
Cause: may cause a low inaccurate MCV value

because of an excessive size Indication: Plt MPV , P2 flag
(+)
Cause: high level of WBC interferes with MCV Use reference manual
determination. Indication: very high WBC (>100,000/ L) , MCHC
methods to determine the accurate MCV value.
MYTHIC 22
Page 45/99
4. SPECIFICATIONS
REF : M22/UM/EN/006
Parameter
Specimen See Hgb value and RBC count interferences See Hgb and HCT values interferences
action
MCH
The MCH is determined according to Hgb value and RBC count. The limitations listed for Hgb and RBC may cause indirect interferences. The MCMH is determined according to Hgb and HCT values. The limitations listed for Hgb and HCT may cause indirect interferences.
(?)
MCHC
RDW
See RBC count interferences
The RDW is determined according to RBC count. The limitations listed for RBC may cause indirect interferences.
Seek for Platelet aggregates on Smear platelet count The specimen should be Indication: aggregates may be detected on the recollected in sodium WBC scattergram with N1 &/or N2 &/or L1 &/or HL citrate anticoagulant and flags, Plt MPV re-assayed
Cause: Clumped platelets may cause a decreased

PLT Platelet Aggregation (-)
Cause: in case of severe microcytosis, microcytes

Severe Microcytosis (+)
and schizocytes are below the RBC inferior Seek for microcytes on threshold and may be counted with Platelets and Smear cause an erroneously high Plt count Indication: RBC, Plt R1 &/or P3 &/or P2 flags
Megalocytic Platelets
(-)
Cause : may cause a low inaccurate platelet count as
these platelets exceed the upper threshold for the Seek for megalocytic platelet parameter and are not counted platelets on Smear Indication : Plt MPV P2 flag
RBC agglutination
(?)
Cause: agglutinated RBC may trap platelets and

cause a low inaccurate Plt count. Indication: abnormal MCH and MCHC values
Seek for clumped RBC on Smear
Hemolysis
(+)
Cause: hemolysed samples contain RBC stromas that

cause a high inaccurate Plt count. Indication: abnormal MCH and MCHC values RBC
Page 46/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
5. SAMPLE ANALYSIS
5.1 VERIFICATIONS BEFORE STARTING
Before starting MYTHIC 22, we recommend to check the reagent levels in each bottle, and the level of the waste container. Please also check the paper quantity in the printer.
5.2 START UP
- Press ON/OFF button on the printer to start. - Switch on the power supply (the power supply can stay on). - Press ON/OFF button on the Mythic.
- The initialization menu is displayed and MYTHIC 22 performs a home position checking for the three motors. - The cycle LED turns green. turns red. None cycle can be performed before it
- Enter your login and password as described in section 3.1. - AUTONOMY (run) indicates the number of samples (runs) you can perform in CBC or DIF mode (calculated with the smaller quantity of reagents).
MYTHIC 22
Page 47/99
5. SAMPLE ANALYSIS
5.3 REAGENT REPLACEMENT
REF : M22/UM/EN/006
The reagents must be stored 24 hours minimum at room temperature before use.
- To check the level of each reagent, press
- If one or more reagent needs to be replaced, proceed as indicated in section 1.5.2 - AUTONOMY (run) indicates the number of samples (runs) you can perform in CBC or DIF mode (calculated with the smaller quantity of reagents).
Page 48/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
5.4 START UP RINSING
- To rinse the system before analysis, press - The cycle LED turns green. turns red. None cycle can be performed before it
- Mythic will perform 1 to 3 empty cycles to check the carry over level. This level should not to exceed the following ratios: WBC : 0.5 RBC : 0.1 HGB : 0,5 PLT : 10 If the level is higher, MYTHIC 22 displays a window START UP FAILED press OK and perform a new start up. If the user chooses to run samples, every result will be printed with Start Up not done message.
5.5 PREPARATIONS BEFORE ANALYSIS

The human blood venous sample must be collected in an EDTA K2 or K3 (Ethylene Diamine Tetracetic Acid, two or tri potassic) tube in sufficient quantity. The 5 part diff results are available (with more flags) up to 48 hours after the blood draw and only if the sample is stored at 4 to 8C. It must be correctly homogenized before analysis. It is recommended to use a rotary agitator turning between 20 to 30 turns/ minutes during 10 minutes. The results and the flags could be affected in case of too much sampling (more than 10 times). A volume of insufficient blood for the quantity of anticoagulant or a bad mixing may involve an erroneous result.
5.6 ANALYSIS 5.6.1 Introduction

It is recommended (or mandatory according to the legislation) to carry out a Quality Control (QC) and possibly a calibration before any analysis (see section 6 & 7). Read the analytical limitations (see section 4.4) before run the sample.
The working temperature of the fluidic part must be reached before starting the analysis. The average time to reach it is around 15 at a room temperature > 23 C (see 5.6.3). If the quality control is not carried out, it is recommended to perform two analyses on a normal sample of the day before, before beginning the series. NOTA: The MYTHIC 22 CT is delivered with a standard parameter setting described in section 3.
MYTHIC 22
Page 49/99
5. SAMPLE ANALYSIS
5.6.2 Sample Identification
- From the main menu, press the analysis display.
REF : M22/UM/EN/006
to reach
- This prompt appears when the results memory is almost full. To avoid this message, select the option FIFO mode in the set up.
- This prompt appears when the results memory is totally full. - To delete results see section 5.10
- The display bottom is reserved for the entry of the next sample identification to run. - Three fields allow the entry of the identification: o ID: Patient Name (20 characters max.) o PID: Patient Identification (16 characters max.) o SID: Sample identification (16 characters max.) NOTA: SID number is already done. (See section 3.3)
- Press - Press
to accede to the blood type and alphabetic characters. or to change the measurement mode.
IDENTIFICATION PROCEDURE: - To enter or modify identification, place the cursor in the selected field with your finger or the arrow. - To enter a figure, use the keyboard on the right of the screen, for a letter use the alphabetic keyboard by pressing - To accede to another character page press - To change the blood type, press the combo box select the type - To valid the entry and return to the previous screen, press - To return to the previous screen without validation, press . or . . and .
Page 50/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
5.6.3 Sample run

Wear rubber gloves and wash hands with a disinfectant after completion of work.
NOTA: The needle will be available as soon as the working temperature is reached (about 15 minutes at 23C of room temperature). This prompt means that the temperature setting of the enclosure and/or the reagent is not reached yet.
This prompt means that the temperature setting of the enclosure and/or the reagent is reached and that a cycle can be run.
As soon as the temperature is reached, a measurement cycle can be run : - If the needle is not visible, first presses the start cycle trigger and wait for the descent. - Present the tube of the blood sample under the needle and press the start cycle trigger. - The cycle LED located at the top of the needle becomes red the tube can be removed only when the needle up. - A new cycle can be started again when it turns by again green.
Start cycle trigger
- As soon as the cycle is launched, the SID is incremented automatically and, thanks to its data processing multitasks, the MYTHIC 22 is available for the identification of the following sample (See section 5.6.2).
MYTHIC 22
Page 51/99
5. SAMPLE ANALYSIS
5.7 RESULTS
REF : M22/UM/EN/006
- The results of the analysis are sent before the cycle is finished (to be checked) at the same time as the printer starts. NOTA: It is not necessary to wait for the end of the result printing to launch a new analysis. - The results are sent to the selected unit (See section 3). - The information located on the right of each parameter corresponds to the indicators for out of range limits and for the rejections (see section 3). - The scattergram and curves of distribution of each cellular population are located on the right screen. - Under the results a zone (FLAGS) is reserved for analytical alarms (see section 8.5). - At the bottom of the screen, there are the three inlet fields for the identification of the next sample. (See section 5.6.2).
- Example of an abnormal result analysis in DIF mode with flags located at the right of the results and in the flag box under the result.
It is mandatory to read the section 8.5 to understand the flags meaning.
- Example of a normal result analysis in CBC mode.
Page 52/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
- Press on the matrix to access to a zoomed view.
- Press on the flags zone to open the flags window. - In regard of the different flags found by the MYTHIC 22 the upper part propose list of the cells to check on the smear. In any case this proposal is a commitment, it is mandatory to read the section 8.5 to understand the flags meaning. Press on flag region to access detailed flags window. - The lower part describes the machine problem (see section 8.5.2).
- Press
to reprint or to resend the result.
- To print the result press - To send the result, press - To close the window, press .
. .
MYTHIC 22
Page 53/99
5. SAMPLE ANALYSIS
5.8 PRINTING
REF : M22/UM/EN/006
Once the analysis is finished, the MYTHIC 22 prints a result report. To modify the printing presentation or to disconnect the printer, see section 3.4.1. To load a new printer driver, see section 3.3.
5.8.1 Model report (A4) external printer

One result per page DIF mode CBC mode
Page 54/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
Two results per page DIF mode CBC mode
5.8.2 Model report Thermal printer

SEIKO DPU 414 model DIF mode CBC mode
MYTHIC 22
Page 55/99
5. SAMPLE ANALYSIS
5.9 LOGS
From the main menu, press
REF : M22/UM/EN/006
to reach the logs display - MYTHIC 22 manage a simplified log allowing saving and displaying all the events done for the following actions: - BIO: Login with the Biologist code. - TEC: Login with the service Technician code. - STC: Login with the Super service Technician code. - INT: An intervention or maintenance has been performed. - SUP: Start Up cycle has been performed. - SUF: Start Up cycle has failed. - SDN: Shut down cycle has been performed. - DIL: Diluent replacement. - LYS: Lysis replacement. - CLN: Cleaner replacement. - ACN: Autocleanning cycle. - BLH: Bleach cycle. - CAL: Calibration. QC: Quality control. DEL: Results deleted in Archive. Each column is identified by a number (recall at the right bottom of the screen ). In the bottom of the screen is displayed the date and under it the number of analysis run during this day. - To print the log report press - Select to print the logs of the number of pages indicated on the screen. - To print the logs of one or more days select then enter the day reference number. allows to save the log file in an USB key.
The recommended maintenances are described in a table section 9.1.1.
5.10 ARCHIVE
MYTHIC 22 CT can save more than the last 500 patients with results, alarms, distribution curves in the internal memory and until a maximum of 60000 results in a memory stick (USB key) of 512 Mbit or more (see section 3.4.7).
- Press
to enter the archive display.
Page 56/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
5.10.1 Results
- The Archive display allows viewing the results of the analysis. - The first column presents the name of the different parameters, the first line the result number. - The results of the patients are presented in column. - At the bottom of the display, under the table, the ID, PID, SID, SEQ number, date and time of the selected patient (dark background) are presented for each result selected. - The button , located under the table, allows changing pages. - To find a result in the list, select the SEQ number wanted, press - To view an entire result, select the SEQ number wanted, press - To print, send, delete or save (in an USB key) results press allows to accede to the results date list.
- It is possible to print, send, delete or save (in a USB key) : . All results: Press . for printing. . Selected results: Select the first and the last results:
Then
press
on or
NOTA : the printed report is a list of all selected patients.
- This prompt appears to confirm the storage in the USB key. If you press YES the selected results will be deleted from the internal memory and stored in the USB key.
- This prompt allows following the storage.
MYTHIC 22
Page 57/99
5. SAMPLE ANALYSIS
5.10.2 View
- Keys identification. and
REF : M22/UM/EN/006
allow displaying each result and its
- To print, send or delete a result, press - The effects of the TOOLS key are as described in section 5.10.1. - The printed report is full page with one or two results per page. - To come back to the archive main page, press - To come back to the Main Menu press . .
- It is possible to print or send: . All results: Press . for printing. . Selected results: Select the first and the last results:
- Then press on
or
This message appears when you exit the result screens and it could stay up to 6 mn to enable the update of all the files.
Page 58/99
MYTHIC 22
REF : M22/UM/EN/006
5. SAMPLE ANALYSIS
5.11 STAND BY AND SHUT DOWN

NOTA: It is recommended to switch off the MYTHIC 22 if it is not use for several hours consecutives. - From the main menu, press . MYTHIC 22 automatically performs a shut down cycle. - All the hydraulic circuits are rinsed, and then cleaned with the cleaning solution. - At the end of the cycle, MYTHIC 22 automatically stop. - Shut Down can be automatically performed after a setting time (see section 3.4.6) NOTA: After a shut down, it is impossible to perform an analytical cycle without launching a start up cycle. (See section 5.2)
MYTHIC 22 must stay at rest with cleaning solution during three hours every 24 hours.
MYTHIC 22
Page 59/99
6. QUALITY CONTROL
REF : M22/UM/EN/006
6. QUALITY CONTROL
6.1 INTRODUCTION
Quality control allows checking the stability of the MYTHIC 22 analytical performances when operating. The control blood must be used before its expiry date and stored according to the manufacturer instructions for use. It must be well-mixed before use. In case of no local regulation, it is recommended to run a control blood at the beginning of each working day before running sample. In case of exceeding the tolerances indicated on the blood control result sheet, it is recommended to perform a Cleaning cycle (see section 9.1.2) followed by a STARTUP cycle. If result still exceeding the tolerances indicated on the blood control result sheet, it is recommended to perform a calibration (see section 7).
6.2 QC
MYTHIC 22 stores in memory up to 100 results per lot, for 6 different lots. Results of each lot can be viewed in tables and Levey-Jennings graph. - Press menu. to have access to the quality control
- Quality control display presents the identification of the lots. - The last active lot is labeled with a dark dot on the left lot. - To choose another lot, press on the wished lot. - The key identification and the target values. - The key USB key. allows the modification of the allows restoring the data from a
- The key allows: . To view the result table. . To perform quality control analysis. - To print, send or save the targets, results and graphics press .
Page 60/99
MYTHIC 22
REF : M22/UM/EN/006
6. QUALITY CONTROL
- Tag the lot number to select then press the appropriate button. the USB key. allows to save the targets, results and graphics in
6.2.1 Change
- In this display, the user can enter the: o Lot number o Expiry date o Target values and tolerances o Level - Press - Press - Press to change the analysis mode. to delete the modifications you made. to validate your modifications or the loading.
- Press to change the Lot number. - To print the targets and limits come back to the previous display. - Press to load the target and tolerances values, the lot number and expiry date from a USB key.
- Select the right lot then press
- Press
to confirm.
MYTHIC 22
Page 61/99
6. QUALITY CONTROL
6.2.2 Run control blood
REF : M22/UM/EN/006
- Press
to run the control blood.
Before to run the control, check and clean the opening of the cover dedicated to the down of the needle to avoid any fall of dry blood particles inside the control tube
- To run quality control analysis: o Present the control blood under the sampling needle. o Press the start cycle trigger. - The cycle LED located at the top of the needle flickers alternatively of red with green, when it becomes red the tube can be removed. - Repeat this operation as long as needed. - The results are displayed in line run after run. - The statistic calculation are shown at the bottom of the display and are automatically done after each run. - The cursor other parameters allows displaying results for the
- The window allows access to the results in memory for another blood control lot. - The column allows to validate or to unselect a result.
- To print, send, delete or save (in an USB key) a result, press
- Press
to open the Levey-Jennings graph screen.
Page 62/99
MYTHIC 22
REF : M22/UM/EN/006
6. QUALITY CONTROL
6.2.3 Levey-Jennings graph

- This menu enables to display the Levey-Jennings graph for each quality control run. - The column on the left shows each parameter with the target values and the limits. The value under the name of the parameter is the value where the cursor is located on the graph. - The keys and enable to display the other results. - The cursor display all the registered results. - The keys number of the result located under the graph enables to
enable to move the cursor; the number is the
give the date and the time of the displayed result.
6.2.4 Restore
- This menu enables to restore all the information (results and targets) for the file selected from the USB key to the internal memory.
- Press YES if you are sure to load the selected file.
All the information of the selected file will be overwrite by the one from the USB key.
6.3 REPEATABILITY
- To run repeatability, press first
MYTHIC 22
Page 63/99
6. QUALITY CONTROL
REF : M22/UM/EN/006
- The key repeatability display.
allows having access to the
This screen allows carrying out a test of repeatability on all the parameters measured by the MYTHIC 22. - Present the sample under the sampling needle and press in the trigger located behind the needle. - The cycle LED located at the top of the needle flickers alternatively of red with green, when it becomes red the tube can be removed. - Repeat the operation as many times as desired (maximum 20 runs). - The results are progressively sent on line in the table. - Statistical calculations are automatically carried out with each run. - The cursor located between the two tables enables to send the other results (the results of statistical calculations move at the same time). - The column allows to validate or to unselect a result.
- The key allows carrying out the following actions: o Print the table. o Send the results. o Delete the results.
Page 64/99
MYTHIC 22
REF : M22/UM/EN/006
7. CALIBRATION
7. CALIBRATION
The calibration of the MYTHIC 22 should be carried out only if the QC carried out on a blood control used under the recommended conditions, is out of the limits to a significant degree (see section 6). Before the launch of a calibration, make sure that the analyzer is ready for use. Do not hesitate to run a cleaning cycle followed by a STARTUP cycle. The calibration blood must be used before its expiry date, be mixed and stored in accordance with the instructions of use recommended by the manufacturer.
- To reach the screen Calibration, press the key from the main menu.
- This menu sends the following information: o Lot number of the last used calibrator. o The expiry date of the current lot. o The last date of calibration. o The operator name. o The target values. o The current coefficients of calibration. - Press values - Press - Press then to enter new values or to modify the to calibrate
, to print these information (see the print out report above). , to send these information. to store these information in the USB key.
MYTHIC 22
Page 65/99
7. CALIBRATION
REF : M22/UM/EN/006
NOTA: If the M letter appears on the right of the date of calibration, that means that the last calibration was done by modification of the calibration factor (see section 3.4.5) Model of print out calibration report:
7.1 RESULTS 7.1.1 Calibration blood analysis

This screen allows carrying out analysis on calibration blood to perform the MYTHIC 22 calibration. - Present the calibration tube under the sampling needle and press the trigger behind the needle. - The cycle LED located at the top of the needle flickers alternatively of red with green, when it becomes red the tube can be removed. - The results are progressively sent on line in the table. - Repeat the operation as many times as desired (maximum 10 runs). - Statistical calculations are carried out automatically with each run. - The window located between the results and the statistical calculation reminds the lot number of the calibrator. - The column allows to validate or to unselect a result. - To calibrate press or .
Before to run the calibrator, check and clean the opening of the cover dedicated to the down of the needle to avoid any fall of dry blood particles inside the calibrator tube
NOTA: The results of the analyses carried out on one calibrator during the same day remain with the screen and are used in calculations if they are selected.
Page 66/99
MYTHIC 22
REF : M22/UM/EN/006
7. CALIBRATION
7.1.2 Calibration
Before to start the calibration, unselect the results which you do not wish to use for the calculation of the calibration (See below section 7.1.1).
- The key or To calibrate with the selected results. To delete the results. Press To print the results. Press report) - To calibrate one or more parameters: Select the parameter Press the key
allows:
(see below the print
7.2 TARGET VALUE MODIFICATIONS

- To modify information relative to a batch or to create a new batch, please follow the following steps: From Calibration Menu, press Select the lot number .
To modify the lot number press Select the field to be modified. Enter your new value with the numerical keyboard or with the alphabetical keyboard. Press Press to validate your modifications or the loading. to leave the menu without modification.
Press to load the target and tolerances values and expiry date and lot number from a USB key.
Any modification (lot number, date or target values) involves the deletion of all the associated results always in memory.
MYTHIC 22
Page 67/99
7. CALIBRATION
REF : M22/UM/EN/006
- Plug the USB key then - Select the right lot then press .
Press to confirm the loading of the target and tolerances values and expiry date and lot number.
Page 68/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
8. TECHNOLOGY
The innovative technology of the MYTHIC 22 is covered by six pending patents. A new innovative concept of optical measurement system and an unique lysing reagent were developed to obtain a so small and powerful analyzer.
8.1 DETECTION PRINCIPLE 8.1.1 WBC, RBC, PLT Counting

The counting of the cellular elements in a blood sample is done with the impedancemetry technique. This technique is based on the modification of the impedance of a calibrated aperture soaking in an electrolyte and going through a constant course delivered by two electrodes located on both sides of the aperture. A vacuum applied on a side of the aperture allows the cells passage. They oppose their physical volume to the course passage. A voltage impulse is registered at the electrodes terminal. The height of this impulse is proportional to the cell volume.
VACUUM
Aperture Electrode Detection area
VOLT
Proportional height to the cell volume
Voltage impulse et the electrode terminal

TIME
Counting Impulse
MYTHIC 22
Page 69/99
8. TECHNOLOGY
8.1.2 Five part diff measurement
REF : M22/UM/EN/006
The innovative optical detection system is covered by two patents pending. This technology (called OCHF for Optical Cytometer Hydrofocus Free) is based on an unique and innovative concept of an active sample flow and a passive sheath. The sample flow is introduced in the flow cell under pressure and the sheath is only dedicated to maintain it. This principle enables to introduce a large quantity of sample and to use a great dilution rate (which allows doing the Hemoglobin measurement with the same dilution). The main advantages are: - High level of reliability of the optical adjustment. - Only two measurement axes for five parameters. - High resolution matrix. - Only one passive sheath with low reagent consumption. - No hydro focusing system. - Low level of contamination between two measurements. - Very low cost flow cell (injected plastic).
- Sample flow - Optical window - Light beam (455 nm wavelength)
- Passive sheath - Injector - Sample
LIGHT INTENSITY
WBC CELL OPTICAL DETECTION AREA SAMPLE FLOW TIME

ALL
For each cell throwing the optical detection area, two pulses are generated, one for the Axis Loss Light (ALL) measurement and one for the Forward Side SCatter (FSC) measurement. The result of those two axes of measurement is the high definition matrix that enables to identify five WBC populations.
FSC
Page 70/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
The five part diff is obtained by the optical matrix analysis after action of the lytic reagent (pending patent). This reagent destroys the RBC and their stromas, composes the oxy hemoglobin chromogen and protects the white blood cell membrane to keep it in closed native state.
EOSINOPHILES
ALL
NEUTROPHILES
BASOPHILES
MONOCYTES
FSC
LYMPHOCYTES
8.1.3 Hemoglobin measurement

The hemoglobin measurement is directly done in the WBC chamber, by spectrophotometry at 555 nm. Hemoglobin is detected by formation of a chromogen oxy hemoglobin type (cyanide free technique). A measurement of the blank of hemoglobin is done for each analytic cycle and during the start up rinsing step. An automatic offset circuit for the LED 555 nm allows maintaining the blank level at the same range. It is not necessary to adjust this range with a potentiometer.
8.2 LEUCOCYTE ANALYSIS

The leukocyte number analysis is done by impedancemetry in the WBC counting chamber, the other ten parameters are obtained by flow cytometry measurement (see section 8.1.2) : All the thresholds of the differential are adjustable in the 20 blood types (see section 3.4.4.2) Parameters White Blood Cells Lymphocytes in percentage Lymphocytes in value Monocytes in percentage Monocytes in value Neutrophils in percentage Neutrophils in value Eosinophils in percentage Eosinophils in value Basophils in percentage Basophils in value Pathologies (adjustment section 3.4.4.1) Leucocytosis : WBC>WBC h Leucopenia : WBC<WBC b Lymphocytosis : LYM>LYM h (% &/or #) Lymphopenia : LYM<LYM b (%&/or #) Monocytosis : MON>MON h (%&/or #) Neutrophilis : NEU > NEU h (%&/or #) Neutropenia : NEU < NEU b (%&/or #) Eosinophilis : EOS > EOS h (%&/or #) Basophilis : BAS > BAS h (%&/or #)
WBC LYM% LYM# MON% MON# NEU% NEU# EOS% EOS# BAS% BAS#
MYTHIC 22
Page 71/99
8. TECHNOLOGY
8.3 ERYTHROCYTE ANALYSIS
REF : M22/UM/EN/006
The erythrocyte analysis is done by impedancemetry in the RBC counting chamber and by analysis of the hemoglobin inside WBC chamber as previously described. Seven parameters are obtained: Parameters Red Blood Cells Hemoglobin Hematocrit Mean Corpuscular Volume Mean Corpuscular Hemoglobin Mean Corpuscular Hemoglobin Concentration Red blood cells Distribution Width Pathologies (adjustment section 3.4.4.1) Erythrocytosis : RBC>RBC h Anemia : HGB < HGB b Microcytosis : VMC<VMC b Macrocytosis : VMC>VMC h Hypochromia : MCHC<MCHC b Cold Agglutinin : MCHC>MCHC h Anisocytosis 1 : RDW>RDW h1
RBC HGB HCT MCV MCH MCHC RDW
Hematocrit (HCT) is measured by integration volume of all of the red blood cells which flow in the RBC counting chamber aperture. MCV is obtained by calculation, following the formula: MCV = HCT 10 RBC The RBC distribution curve analysis allows the measurement of RDW. RDW is an expression of the standard deviation divided by MCV. This parameter evaluates the RBC anisocytosis. RDW = k SD MCV
Wintrobe constant calculation: The Mean Corpuscular Hemoglobin (MCH) calculation is made from HGB and RBC by the formula below : MCH = HGB 10 RBC The Mean Corpuscular Hemoglobin Concentration (MCHC) is made from HGB and HCT by the formula below : MCHC = HGB 100 HCT
Page 72/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
8.4 ANALYSIS OF PLATELETS

Platelet analysis is made by impedancemetry in the RBC counting chamber at the same time with red blood cells. Four parameters are obtained: Parameters PLT MPV PDW PCT Platelets Mean Platelet Volume Platelet Distribution Width Thrombocrit Pathologies (adjustment section 3.4.4.1) Thrombopenia : PLT<PLT b Thrombocytosis : PLT>PLT h Giant platelets : MPV> MPV h
The analysis of the platelet distribution curve allows measuring the Mean Platelet Volume (MPV) and the Platelet Distribution Width (PDW). Thrombocrit (PCT) is made from PLT and MPV by formula below: PCT = PLT MPV 10000
8.5 FLAGS
MYTHIC 22 CT manages 25 different flags. These flags allow the user to be alerted if there is a problem which can affect the quality of the results. All of these flags appear on the right of the result. In presence of one or more flags, it is recommended to check the result by a conventional measure or on blood smear. NOTA: Most of these flags can be modified by the user (see section 3).
8.5.1 General Flags

The following alarms are common for all parameters. XXX *: Counting or measure rejection. It can appear with WBC, RBC, PLT and HGB (see section 8.5.3 for HGB and section 8.5.2 for DIF parameters). XXXD: Higher than linearity limits but lower than the reportable limits. WBC, RBC, PLT, HCT, HGB. +++D: Higher than the reportable limits. WBC, RBC, PLT, HCT, HGB. ----: Rejected value. h: results higher than normal value. b: results lower than normal value. H: results higher than panic value. B: results lower than panic value.
MYTHIC 22
Page 73/99
8. TECHNOLOGY
8.5.2 Instrument Flags
REF : M22/UM/EN/006
W_CL: Suspicion of WBC aperture clog, if it persists runs a concentrated cleaning (see section 9.1.2). R_CL: Suspicion of RBC aperture clog, if it persists runs a concentrated cleaning (see section 9.1.2). O_CL: Suspicion of Optical injector clog, if it persists runs a concentrated cleaning (see section 9.1.2). OPT- : Counting gap between resistive and optical WBC count, if it persists run a concentrated cleaning (see section 9.1.2). INS-H: HGB channel saturation, run a START UP cycle. INS-T: A temperature (enclosure, reagents or ambient) is out of range (see section 9.5.2) INS-P: Pressure default (see section 9.5.2).
Page 74/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
8.5.3 Leucocytes Flags

SCATTERGRAM FLAGS:
NH
NL IC N1 N2 HL RL
All the followings flags levels are adjustable in the 20 types of blood (see section 3.4.4). Number of cells in a zone: N1 (Noise 1): Presence of platelet aggregate, debris or resistant RBC N2 (Noise 2): Presence of platelet aggregate, erythroblast or small lymphocytes. IC: Presence of Immature Cells (from the mono or polynucleated cells line) Number of cells located of each side of the threshold: RL (Right Lymphocytes: Presence of atypical lymphocytes or basophiles. HL (High Lymphocytes): Presence of basophiles, small Neutrophils (without granulations or few segmented), band cells. NL (Neutrophils Low): Presence of small Neutrophils (without granulations or few segmented), band cells or hyper basophil Monocytes. NH (Neutrophils High): Presence of giant Neutrophils, hyper segmented Neutrophils, eosinophils with few granulations or damaged eosinophils. These flags may appear if the blood was not store in good conditions or if it was sampled too much (more than 10 times). DIF parameters display rules: - If one or more DIF parameters (LYC, MON, NEU, EOS or BAS) are following with a star (XXX *) the sample must be checked on smear. - Basophile result must be checked on smear if it is following by a star (XXX *).
MYTHIC 22
Page 75/99
8. TECHNOLOGY
REF : M22/UM/EN/006
WBC CURVE FLAGS: This curve is done by the WBC channel measurement and does not appear on the normal results screen. The flags L1 and L5 complete the flags N2 and IC.
CL1
CL5
L1 = Presence of platelet aggregate, erythroblast or small lymphocytes at the left of CL1. L5 = Presence of immature cells at the right of CL5.
8.5.3 Erythrocyte and HGB Flags

CR1 CR2 R1 = Abnormal quantity of microcytes at the left side of CR1. R2 = Abnormal quantity of macrocytes at the right side of CR2. HGB: * means bad measure of the HGB blank.
8.5.4 Platelet Flags

CP3-2
CP1
CP2
CP3
P1 = 0 to CP1: Presence of abnormal quantity of debris or small cells. P2 = P to CP2: Presence of schizocytes. P3 = CP3 to CP3-2: Presence of microcytes.
8.5.5 QC Flags
QC_F: QC Failed means that the results are outside the limits entered for one or several parameters (see section 6.2.1). QC_ND: QC Not Done means that the Quality Control has not been done or that the analysis are done with QC results outside the limits (see section 6.2.1).
8.5.6 STARTUP Flags

SU_F: STARTUP Failed means that the results are outside the limits for one or several parameters (see section 5.4). SU_ND: STARTUP not done means that the Start Up has not been done or that the analysis are done with results of the Start Up outside the limits (see section 5.4).
Page 76/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
8.6 HYDRAULIC DESCRIPTION

The hydraulic part of the MYTHIC 22 is very simple and made of these modules: - Sampling module. - Counting bath module. - Syringes module. - Optical manifold. - Optical bench. The modules are connected together by semi rigid tubing.
8.6.1 Sampling module

This module (patent pending) enables to draw the sample and to perform the WBC and RBC/PLT dilutions. It is assembled with a rotating rocker moving around a support which maintains the system to move up and down the sampling needle. A very reliable system of rack-gear moves the rocker. The cleaning system of the sampling needle can be removed without tool (see section 9.3.2). The o-ring of the needle included in the cleaning system can also be removed without tool (see section 9.3.2). The maintenance of these parts is very easy to perform.
8.6.2 Counting bath module

This module allows to count the WBC and RBC/PLA and to measure the HGB. It is made with a manifold maintaining the reagent commutation valves and the counting bath block with their measurement block including the apertures. The counting bath block assembly and these apertures can be removed without tool (see section 9.3.3/4/5).
8.6.3 Syringes module

This module (two patents pending) enables: to draw the sample to distribute the reagents to drain the baths to do the vacuum necessary for counting to push the waste to the waste container to push the WBC sample and the diluent sheath in the flow cell . It is made with a manifold maintaining the fluid commutation valves and with the syringes bloc including five syringes : The sampling syringe The lysis syringe The two waste and vacuum/pressure syringes And the diluent syringe. Only one motor drives the five syringes. The diluent input and the waste output are also included in this manifold.
8.6.4 Optical manifold

This manifold allows driving the different reagent toward the counting bath module or toward the optical bench. It maintain seven commutation valves
MYTHIC 22
Page 77/99
8. TECHNOLOGY
8.6.5 Optical bench
REF : M22/UM/EN/006
This very important part (two pending patents) allows to measure the leucocytes sub population. It is made of three parts: - An illumination module: which contain the semi conductor light source, a beam adjustment glass smear, and lens. - A flow cell: made in injected plastic in which the sample and the passive sheath flow away. - And the detection module: which contains lens, a beam separation glass smear, photodiodes and the amplifier boards for the two measurement axes.
8.8 SOFTWARE 8.8.1 Windows

Common keys: These three keys allows to come back to the previous display. allows to come back to the MENU display where ever you are in the arborescence. depends on the screen it allows to open a window dedicated to perform an action, for example to select information, to print, send or delete it. Windows: are always present in all screen
Means an ERROR occurred, it is mandatory to do the action describe in the window or in the table section 9.6.
WARNING: You have to confirm or not the action describe in the window.
INFORMATION window.
8.8.2 Menu tree

See next page.
Page 78/99
MYTHIC 22
REF : M22/UM/EN/006
8. TECHNOLOGY
MYTHIC 22
Page 79/99
9. SERVICE
REF : M22/UM/EN/006
9. SERVICE
The quality of the results and the reliability of the MYTHIC 22 are directly linked to the strict respect of the maintenance hereafter described. To perform the maintenance and the repair described in this section, it is mandatory to have received adequate training, to wear rubber gloves and wash hands with a disinfectant after completion of work.
9.1 MAINTENANCE 9.1.1 Maintenance table

NOTA: This table is made for an average number of 50 samples per day. For more, please increase proportionally the number of maintenances. MAINTENANCE Reagents level Start Up Automatic cleaning Concentrate cleaning Shut down Cover cleaning Piston greasing Needle greasing Needle o-ring replacement Syringes o-ring replacement Motor screw greasing X X X X X X X X X
DAILY User Tech WEEKLY User Tech QUARTERNALY User Tech HALF A YEAR User Tech ANNUALLY User Tech
X X X
- Reagents level control: see section 5.3 - Start up: see section 5.2 - Automatic Cleaning: The cleaning is automatically performed by the MYTHIC 22 following the set up defined by the user (see section 3.3.6). (The standard value is 80). Increase the frequency of the cleaning of the MYTHIC 22 in case of analyzes of pathological samples or if there are too many flags and too often. - Concentrated cleaning: see the following section 9.1.2 - Shut down: see section 5.11 - Cover cleaning: Clean the cover above and around the sampling needle with a wet paper with a disinfectant to eliminate the blood trace. - Piston greasing: see section 9.1.3 NOTA: Maintenance informations are registered in a log (see section 5.9).
Page 80/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
9.1.2 Concentrate cleaning

This cleaning is necessary once a week to clean the WBC and RBC baths or when MYTHIC 22 is in permanent rejection for one measured parameter or if it give too much clog flags (see section 8.5.1). Prepare a Sodium Hypochlorite solution at 12 in chloride (diluted 4 times with distilled water if sodium hypochlorite is concentrated at 48 in chloride or three times with 36).
- Return to the main menu by pressing - Then press .
- Press
- Press chamber).
to start the cycle (drain the counting
MYTHIC 22
Page 81/99
9. SERVICE
REF : M22/UM/EN/006
- Open the door on the right side (see section 1.1.3). - Put 3 ml of sodium hypochlorite solution in each counting chamber. - Press the button in the window located in the screen center. - MYTHIC 22 performs a maintenance cycle of the apertures and the flow cell follow with a standby mode during 2 min. - After 2 min. MYTHIC 22 rinses all of the elements. Operator can perform an analytic cycle. Wear rubber gloves and wash hands with a disinfectant after completion of work.
9.1.3 Piston greasing
- To have access to the hydraulic cycle, press from the MAIN MENU, then press
NOTA: The greasing frequency must be increase proportionally to the number of samples per day (See maintenance table 9.1.1).
Operators must be trained and to know that due to moving parts there is a risk to pinch their fingers between pistons and the syringe body.
- Press in the greasing position.
to put the piston of the syringe module
Page 82/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
Wear rubber gloves and wash hands disinfectant after completion of work. - Open the door on the right side (see section 1.1.3). - Put a small nut of grease on a finger.
with
- Put a THIN FILM of grease around each piston.
- Turn the two big pistons (waste pistons) with the help of the key supplied in the installation kit. - Continue to put a thin film of grease around each piston. - The other pistons can be turned with fingers.
9.2 HYDRAULIC CYCLES
- To have access to the hydraulic cycle, press from the MAIN MENU, then press
MYTHIC 22
Page 83/99
9. SERVICE
REF : M22/UM/EN/006
- To drain the counting baths the flow cell and the waste syringes, press
- To fill the counting baths and the flow cell with diluent, press
- To perform a cleaning of the aperture blocks and the flow cell with the cleaner, press - To perform a back flush in the aperture blocks and the flow cell, press
9.3 MECHANICS
- To have access to this cycle, press MAIN MENU, then press
from the
see below. performs a complete test of the needle. performs a complete test of the rocker. performs a complete test of the syringe. see below. switches on (or off) the HGB led to check it. switches on (or off) the optical led to check it. see section 9.4.2 see section 9.1.3 Page 84/99 Copyright Orphe SA. All Rights Reserved. MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
- This screen allows checking if the different sensors are available in case of problem. NOTA: To understand the function of each sensor we recommend to do an Orphes training. - Range of standard temperature measured by the sensors: Ambient: 17C <--> 37C Enclosure: 33C <--> 40C Reagents: 34C <--> 45C
- To test each valve, press the dedicated button.
- To test all the valves press
9.4 REPAIRING 9.4.1 Emergency stop

In case of mechanical or hydraulic problem, immediately press MYTHIC 22 will make an emergency stop. , the
- After having identified the problem, it is necessary to perform a Control cycle. - To have access to this cycle, press MAIN MENU, then press from the
MYTHIC 22
Page 85/99
9. SERVICE
9.4.2 Needle or o-ring replacement
REF : M22/UM/EN/006
- From the main menu, press
then
to go to the display described on the left. - Press on - The rocker places the sampling needle in the disassembling position. - Open the door located on the right side to have access to the hydraulic part.
- The needle is in front of the counting chambers
- Remove the sampling module, while slightly lowering the clip bottom.
1 to the
Page 86/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
- Draw the system towards outside
2.
- Remove the tubing fixed at the end of the needle.
- Unscrew the serrated roller which maintains the seal and the needle.
- Leave the serrated roller, the needle and the o-ring from the rinsing head.
MYTHIC 22
Page 87/99
9. SERVICE
REF : M22/UM/EN/006
- Remove the o-ring. - Replace the needle with or the o-ring.
REASSEMBLY PROCEDURE: To reassemble the unit, carry out the various operations in the opposite direction. Place the seal on the needle gently not to wound it.
9.4.3 Baths dismantling

This procedure must be carried out to replace the bath seals on the manifold or the aperture seals. Wear rubber gloves and wash hands with a disinfectant after completion of work.
- From the MAIN MENU, press .
then press
- Press baths.
to perform a draining of the counting
- Open the door located on the right side of the instrument to have access to the hydraulic part.
Page 88/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
- To remove the counting bath module, draw on the clip machine
1 while
pushing the top from the counting bath towards the inside of the
2.
- Then, upwards, raise the counting module.
- Next, remove the tubing fixed on the RBC counting head, located on the right side of the counting module.
MYTHIC 22
Page 89/99
9. SERVICE
REF : M22/UM/EN/006
- Remove the tubing fixed on the plastic fitting located under the stainless tube from WBC counting block.
- Remove all connectors.
- The counting bath module can now be handled to carry out the desired operations of replacement. REASSEMBLY PROCEDURE: To reassemble the unit, carry out the various operations in the opposite direction.
Page 90/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
9.4.4 Baths o-ring replacement

- Before performing the operation, drain the baths and dismantle the counting bath block (see section 9.4.3). - Replace the o-ring and/or the complete bath block. REASSEMBLY PROCEDURE: To reassemble the unit, carry out the various operations in the opposite direction. Place the seal on the counting bath gently not to wound it.
9.4.5 Aperture block replacement

- Before performing the operation, drain the baths and dismantle the counting bath block (see section 9.4.3). - Remove the tubing from the blocks to be replaced. - With the help of the provided tool in the maintenance kit, unscrew the screw and remove the connection. NOTA: This operation can be performed without dismantling the complete bath block.
- Unscrew the aperture block of a quarter of turn.
MYTHIC 22
Page 91/99
9. SERVICE
REF : M22/UM/EN/006
- Remove the o-ring and replace by a new one or replace the whole part.
NOTA: The WBC aperture block is marked with a figure 8 on the ear and with a figure 5 for the RBC.
REASSEMBLY PROCEDURE : To reassemble the unit, carry out the various operations in the opposite direction. Place the seal on the aperture block gently not to wound it.
9.5 TROUBLESHOOTING
In any case, if a problem is not solved, call Orphes representative.
9.5.1 Analytical problems

PARAMETERS WBC PROBLEMS No result CONDITIONS SOLUTIONS No HGB Check the lysis level. Check the right lysis tubing connection to the WBC bath. Check the valve Nb 9. HGB OK Check the bath wires. Perform a Cleaning Cycle and then a Bleach cycle if unsuccessful. Change the aperture block if unsuccessful. Bad stability Perform a Back flush and a Cleaning Cycle and then a Bleach cycle if unsuccessful. Check the level bubble flow in the WBC bath during the run cycle. Check the reagent and enclosure temperature. No result or No HGB Check the lysis level. bad stability & WBC Check the right lysis tubing connection to the WBC bath. Check the valve Nb 9. HGB & WBC Perform a Back flush Cycle and then a Bleach cycle if unsuccessful. OK Check the valves Nb 12, 13, 16 & 17. Check the reagent and enclosure temperature. Check the preamp connection wires. Rejection * Check the results on blood smear. No result No HCT & PLT Check the bath wires. Perform a Cleaning Cycle and then a Bleach cycle if unsuccessful. Bad stability HCT & PLT Perform a Back flush and a Cleaning Cycle and then a Bleach cycle if unsuccessful. Check the level bubble flow in the RBC bath during the run cycle. Check the level bubble flow in the WBC bath during the first dilution. No result Check the led light on Bad stability Check if no bubble in the lysis tubing. Check the reagent and enclosure temperature. Check the level bubble flow in the WBC bath during the run cycle. Rejection --Close the door. * Perform a new Start Up cycle. Flag INS_H Perform a new Start Up cycle.
5 DIFF
RBC
HGB
Page 92/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
9.5.2 Other problems

ORIGIN MYTHIC PROBLEMS SOLUTIONS Diluent leaks around the Check the rinsing needle block (presence of clots) and clean needle during the run cycle it if necessary see section 9.4.2 No starting Check the power supply connection wires Check the switch on button located on the power supply block. All results bad Check the level diluent and if the tubing is pinched. Check if the diluent is at the same level than the analyzer. No display Check the flat cable. ID and/or PID typing ID and/or PID are mandatory (see section 3.4.3). impossible
Message : TEMPERATURE Check the origin of the problem of temperature in section 9.3. OUT OF RANGE or flag Trigger temperature values: INS_T Ambient: 17C <--> 37C Enclosure: 33C <--> 40C Reagents: 34C <--> 45C
Message: CYCLE: PRESSURE Cases of occurrence: DEFAULT or Flag INS_P - drain chamber default: check the tubing connection of the fluidics
- counting vacuum default: perform a piston greasing (see section 9.1.3) and check the tubing connection of the fluidics
For all occurrences check also the level of the reagents.
Printer
No printing Bad printing
Check the paper. Check the electrical connection. Check the black ribbon.
9.6 TROUBLESHOOTING MESSAGE

This section allows knowing what to do when a troubleshooting message appears on the screen. If the problem go on contact your Orphee representative.
MESSAGE BACKUP : FOLDER NOT FOUND BACKUP: BAD FOLDER DUPLICATION BACKUP: CALIBRATION HISTORY IS FULL BACKUP: FAIL TO SAVE RESULT ONTO THE EXTERNAL STORAGE DEVICE. THE INTERNAL MEMORY IS USED. BACKUP: FILE SYSTEM FAILED. BACKUP: LAST RESULT SAVED. ACTION Re-start the Mythic. Re-start the Mythic Delete the calibration results. Please connect USB thumb drive to the analyzer Re-start the Mythic. Memory full, next result will not be saved. You have to delete
MYTHIC 22
Page 93/99
9. SERVICE
MESSAGE BACKUP: MEMORY IS ALMOST FULL. PLEASE DELETE RESULTS. BACKUP: NO MEMORY AVAILABLE FOR STORAGE BACKUP: QC HISTORY IS FULL BACKUP: REPEATABILITY HISTORY IS FULL BACKUP: SECTOR FAILED. BACKUP: SYSTEM ERROR CLEAN NOT DONE CLEANER ALMOST EMPTY COM: BAD CYCLE MODULE COM: CRC CONTROL ERROR COM: SIZE ERROR. CONTROL CYCLE NOT DONE CYCLE STOPPED BY USER CYCLE: BUSY CYCLE: CMD VALVE FAILED CYCLE: EMERGENCY STOP CYCLE: FLUIDIC DOOR OPENED CYCLE: HGB CHANNEL SATURATION. PLEASE RUN STARTUP. CYCLE: INIT NOT DONE CYCLE: PRESSURE DEFAULT CYCLE: VALVE XX FAILED DILUENT ALMOST EMPTY HARDWARE: A.L.L BOARD ID FAILED. HARDWARE: F.S.C BOARD ID FAILED. HARDWARE: FAN FAILED. HARDWARE: HEAT ENCLOSURE FAILED. HARDWARE: HEAT ENCLOSURE STOPPED. HARDWARE: HEAT REAGENT FAILED. HARDWARE: HEAT REAGENT STOPPED. HARDWARE: SYSTEM ERROR ACTION results. Delete results Delete the stored results.
REF : M22/UM/EN/006
Delete the Q.C. results of the ongoing lot. Delete the repeatability results. hardware failure on memory Re-start the Mythic. Perform a rinse cycle. Replace the bottle and perform a prime Cleaner Rebuild cycles with good options Communication error retry Try to send the file again If the problem still occurs, call an Orphe representative. Perform a control cycle. Emergency stop, please perform a control cycle. Wait before performing a cycle. Change the valve Perform a control cycle. Close the door, in case of emergency stop run a control cycle Run Startup Cycle. If the problem still occurs, call an Orphe representative. Perform an initialization or a control cycle. May occurred by leak of reagent, check tubing in the fluidics Change the valve Replace the container and perform a prime Diluent check the hardware connection on ALL Board check the hardware connection on FSC Board check if your temperature fan is running Call an Orphe representative. check your enclosure sensor Call an Orphe representative. check your reagent sensor Re-start the Mythic.
Wait for the system to reach its temperature HEATING IN PROGRESS, PLEASE WAIT. ID AND/OR PID MANDATORY (CHECK SETUP). SID Enter an ID and/or PID and SID ALWAYS MANDATORY. INIT PRINTER INTERN: COUNT ERROR INTERN: MEMORY CORRUPTED INTERN: NO MEMORY AVAILABLE INTERN: RESULT AREA IS LOCKED INVALID DATA FORMAT. LOT ALREADY EXISTS. ACTION CANCELLED. LYSE ALMOST EMPTY MECA: HOME NEEDLE NOT FOUND MECA: HOME ROCKER NOT FOUND Switch on the printer or invalidate the printings. Re-start the Mythic. Re-start the Mythic. Re-start the Mythic. Wait before performing a cycle. If persisting, re-start the Mythic. The files format are not available for the Mythic Select other lot Replace the bottle and perform a prime Lysis Perform an initialization or a control cycle. Perform an initialization or a control cycle.
Page 94/99
MYTHIC 22
REF : M22/UM/EN/006
MESSAGE MECA: HOME SYRINGE NOT FOUND MECA: MOTOR NEEDLE BUSY MECA: MOTOR ROCKER BUSY MECA: MOTOR SYRINGE BUSY MECA: MOTOR SYRINGE GAP MECA: NEEDLE NOT IN TOP POSITION NETWARE: SERVER INIT. FAILED NETWARE: CLIENT INIT. FAILED. NO PRINTER RESPONSE NO PRINTER SELECTED NO PRINTER SELECTED NUMBER MAX. OF FILES REACHED. PLEASE DELETE FILES. OUT OF RANGE PRINTER DRIVER UPDATE FAILED. THE CHOSEN DRIVER IS NOT COMPATIBLE WITH THE MYTHIC 22 SYSTEM. PRINTER ERROR PRINTER IS BUSY PRINTER IS OFF PRINTER: NO PAPER RINSE NOT DONE RS232: ACK ERROR RS232: INTERNAL ERROR RS232: SYNCHRO ERROR RS232: TIME OUT RUNNING AUTO CLEANING SET TEMPERATURE REACHED. SETUP: MODIFICATION NOT ALLOWED. START UP CYCLE NOT DONE STARTUP CYCLE FAILED SVM: BAD VERSION SVM: COM. TIME OUT SVM: ILLEGAL SERIAL NUMBER. SVM: UNMATCH SVM: WG SVM: XB ACTION Perform an initialization or a control cycle. Re-start the Mythic. Re-start the Mythic. Re-start the Mythic. Perform a pistons greasing Perform a control cycle. Call an Orphe representative. Call an Orphe representative.
9. SERVICE
Switch on the printer or invalidate the printings. Switch on the printer or invalidate the printings. Switch on the printer or invalidate the printings. Delete some files Modify the value Select the correct version Switch on the printer or invalidate the printings. Switch on the printer or invalidate the printings. Switch on the printer or invalidate the printings. Add some paper. Perform a clean cycle. Re-start the Mythic. Re-start the Mythic. Re-start the Mythic. Re-start the Mythic. Press OK. The samples can be run You have to be Logged with the good access code Perform a start up cycle. Perform a new start up cycle Update the SVM software Re-start the SVM. This MYTHIC can not be connected to the SVM Re-enter the file or confirm it (manual connection on the SVM). Westgard alarm. XB alarm.
SYSTEM LOCKED HEATING FAILED Call an Orphe representative. SYSTEM: DOWNLOADING NEW VERSION. PLEASE System is resetting after version release WAIT SYSTEM: EEPROM COM ERROR SYSTEM: FATAL ERROR SYSTEM: INTERNAL TIME OUT TEMPERATURE OUT OF RANGE THE CLEANER USED IS OUT OF DATE. THE DILUENT USED IS OUT OF DATE. THE LYSE USED IS OUT OF DATE. USB: DIRECTORY DOES NOT EXIST. Re-start the Mythic. Re-start the Mythic. Re-start the Mythic. Room temperature out of the limits (<18 or >34C). Replace the bottle and perform a prime Cleaner Replace the container and perform a prime Diluent Replace the bottle and perform a prime Lysis Try again or change for another USB Thumb.
MYTHIC 22
Page 95/99
9. SERVICE
MESSAGE USB: DIRECTORY IS NOT EMPTY. USB: EMPTY FILE USB: THUMB DRIVE I/O ERROR USB: THUMB DRIVE IS FULL. USB: THUMB DRIVE IS NOT PRESENT. USB: TOO MANY FILES OPENED. USB: UNABLE TO CREATE DIRECTORY. USB: UNABLE TO OPEN DIRECTORY. USB: UNABLE TO OPEN FILE USB: WRITE PROTECTED FILE. VERSION RELEASE FAILED. THE CHOSEN RELEASE IS NOT COMPATIBLE WITH THE MYTHIC 22 SYSTEM. WASTE ALMOST FULL ACTION
REF : M22/UM/EN/006
Try again or change for another USB Thumb. Try again or change for another USB Thumb. Try again or change for another USB Thumb. Delete some files Please connect USB thumb drive to the analyzer Delete some files Try again or change for another USB Thumb. Try again or change for another USB Thumb. Try again or change for another USB Thumb. Try again or change for another USB Thumb. Select the correct version Replace the waste container
Page 96/99
MYTHIC 22
REF : M22/UM/EN/006
9. SERVICE
9.7 LOGS ERRORS

- From the MAIN MENU press - Then press .
- This screen allows visualizing the date and timing when an error has occurred, as well as the code and the origin of this error. - To see the origin of the error, press on the figure located on the left of the date, the complete error appears at the bottom. - To print it press .
- Select to print the errors of the number of pages indicated on the screen. - To print or save (in an USB key) the error of one or more days select then enter the error reference number.
MYTHIC 22
Page 97/99
9. SERVICE
REF : M22/UM/EN/006
9.8 HYDRAULIC DIAGRAM

The length and inner diameters of the tubing shown on the diagram below the tubing table must be strictly respected when replaced, otherwise there is a significant risk in the quality of results given.
ID 1,55x3,4mm ID 1x3mm PU ID 2,4x4mm 5mm 5mm 510mm 240mm 270mm 130mm 230mm 190mm 180mm 180mm 960mm 200mm 180mm 250mm 3 x 15mm 270mm 100mm 400mm 240mm 150mm 70mm 100mm 50mm 60mm 365mm 140mm 10mm 80mm 1000mm 8mm 15mm 2 x 20 mm 180mm 5mm 3 x 15 mm 2x5mm 5mm 2x5mm 2x5mm ID 1,3x3mm ID 2,1x4mm ID 1x2.7mm ID 2,79 mm ID 0.38 mm ID 0.89 mm
ID 3x6mm
Designation Tubing 5 Tubing 6 Tubing 8 Tubing 12 Tubing 13 Tubing 14 Tubing 17 Tubing 18 Tubing 22 Tubing 23 - DILUENT Tubing 24 - WASTE Tubing 25 Tubing 26 Tubing 3 Tubing 9 Tubing 10 Tubing 30 Tubing 31 Tubing 32 Tubing 33 Tubing 34 Tubing 35 Tubing 36 Tubing 37 Tubing 38 Tubing 39 Tubing 40 Tubing 41 Tubing 42 Tubing 43 Tubing 44 Tubing 45 Tubing 46 Tubing 47 Tubing 48 Tubing 49 Tubing 50 Tubing 51 Tubing 52 Tubing 53 Tubing 54 Tubing 55 Tubing 56 Tubing 57 Tubing 58 Tubing 59 500mm 130mm 80mm 40mm 2 X 10mm 135 + 20 mm 200mm 1500mm 1500mm 55mm (45) 5mm 80mm 60mm 250mm 250mm 80mm 80mm 210mm 130mm
Page 98/99
MYTHIC 22
ID 5x8mm
REF : M22/UM/EN/006
9. SERVICE
MYTHIC 22
Page 99/99

Orphee Mythic 22 Hematology Analyzer - User Manual

Uploaded by

Copyright:

Available Formats

Orphee Mythic 22 Hematology Analyzer - User Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Orphee Mythic 22 Hematology Analyzer - User Manual

Uploaded by

Copyright:

Available Formats

mythic 22

CONTACT ADDRESS MANUFACTURER

Copyright Orphe SA. All Rights Reserved.

READ THIS BEFORE USING THE EQUIPMENT

KEEP THESE INSTRUCTIONS

Copyright Orphe SA. All Rights Reserved.

IEC 61000-3-2 Voltage fluctuations/flicker emissions IEC 61000-3-3

Electromagnetic environment - guidance

IEC 60601 test level

Electromagnetic environment - guidance

2 kV for power supply lines 1 kV for input/output lines

Mains power quality should be that of a typical commercial or hospital environment.

Power frequency (50/60 Hz) magnetic field IEC 61000-4-8

Copyright Orphe SA. All Rights Reserved.

d = 1,2P 80MHz to 800MHz d = 2,3P 800MHz to 2,5GHz

Copyright Orphe SA. All Rights Reserved.

Copyright Orphe SA. All Rights Reserved.

KONFORMITTSERKLRUNG / DECLARATION DE CONFORMITE DECLARATION OF CONFORMITY / DICHIARAZIONE DI CONFORMITA

Mythic 22 Ref. M22OT

Copyright Orphe SA. All Rights Reserved.

Philippe Daire RA & QA

Copyright Orphe SA. All Rights Reserved.

4.4 ANALYTICAL LIMITATIONS ................................................................................................................................................................... 42

Copyright Orphe SA. All Rights Reserved.

8.6 HYDRAULIC DESCRIPTION...................................................................................................................................................................... 77

Copyright Orphe SA. All Rights Reserved.

Copyright Orphe SA. All Rights Reserved.

1.1.2 Unpacking Procedure

Copyright Orphe SA. All Rights Reserved.

1.1.3 Visual checking

1.2 INSTALLATION CONSTRAINTS 1.2.1 Installation place

1.2.2 Installation environment

Copyright Orphe SA. All Rights Reserved.

1.3 ELECTRICAL CONNECTIONS

- External barcode reader (RS232C) : - Host connection (RS232C) :

- Printer connection (Centronics) :

- Power supply cord connection :

1.3.1 Power supply block

1.4 PRINTER CONNECTION

Copyright Orphe SA. All Rights Reserved.

1.5 CONNECTION, CHANGE AND PRIMING REAGENTS

Copyright Orphe SA. All Rights Reserved.

Copyright Orphe SA. All Rights Reserved.

- Press priming cycle. - The cycle LED green.

: The MYTHIC 22 performs a complete

turns red. No cycle can be performed before it turns

Copyright Orphe SA. All Rights Reserved.

- A new entry is automatically done in the logs (see section 5.9)

MYTHIC 22 IS NOW READY TO WORK.

1.6 TRANSPORTATION AND STORAGE

Copyright Orphe SA. All Rights Reserved.

* For Investigation Use only in the United States of America

Copyright Orphe SA. All Rights Reserved.

2.3 MAIN PART DESCRIPTION 2.3.1 Display / Keyboard

Copyright Orphe SA. All Rights Reserved.

Back to previous screen

Direct access to main menu

Date and time. System status (Section 3.2).

Cleaning and standby mode

Reagents replacement (Section 5.3).