Scribd
Upload
8K views26 pages

Fingerprint Based Bank Locker System

NOTE: it usually takes some time to reply to your queries because i have a lot of work and i'm not on scribd frequently so please be patient. thanks The present scenario to operate a bank locker is with locks which are having keys. By this we can’t say that we are going to provide good security to our lockers. To provide perfect security and to make our work easier, we are taking the help of two different technologies viz. EMBEDDED SYSTEMS and BIOMETRICS. Firstly discussing about Biometrics we are concentrating on Fingerprint scanning. For this, we are using FIM 3030N high voltage module as a scanner. This module has in-built ROM, DSP and RAM. In this, we can store the fingerprints of up to 100 users. This module can operate in 2 modes i.e., Master mode and User mode. We will be using Master mode to register the fingerprints which will be stored in the ROM present on the scanner with a unique id. When this module is interfaced with the microcontroller, we will be using it in user mode. In this mode, we will be verifying the scanned images with the stored images. When coming to our application, the images of the persons who are authorized to enter into the locker room will be stored in the module with a unique id. To prove that the persons are authorized to enter that area, they need to scan their images. This scanner is interfaced with 8051 microcontroller. By using this controller we will be controlling the scanning process. After scanning has been completed, the person has to enter his unique id to open his locker with the help of a keypad. Immediately the locker will be opened. After the work has been completed, the locker will be closed again if a switch is pressed. If an unauthorized person tries to scan his image, then an indication will be given by a buzzer which is interfaced with the controller. If an authorized person forgets his id, he will be given 3 chances to re-enter the id. This project uses regulated 5V, 500mA power supply. 7805 three terminal voltage regulator is used for voltage regulation. Bridge type full wave rectifier is used to rectify the ac out put of secondary of 230/12V step down transformer.

Uploaded by

rockfloyd
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
8K views26 pages

Fingerprint Based Bank Locker System

NOTE: it usually takes some time to reply to your queries because i have a lot of work and i'm not on scribd frequently so please be patient. thanks The present scenario to operate a bank locker is with locks which are having keys. By this we can’t say that we are going to provide good security to our lockers. To provide perfect security and to make our work easier, we are taking the help of two different technologies viz. EMBEDDED SYSTEMS and BIOMETRICS. Firstly discussing about Biometrics we are concentrating on Fingerprint scanning. For this, we are using FIM 3030N high voltage module as a scanner. This module has in-built ROM, DSP and RAM. In this, we can store the fingerprints of up to 100 users. This module can operate in 2 modes i.e., Master mode and User mode. We will be using Master mode to register the fingerprints which will be stored in the ROM present on the scanner with a unique id. When this module is interfaced with the microcontroller, we will be using it in user mode. In this mode, we will be verifying the scanned images with the stored images. When coming to our application, the images of the persons who are authorized to enter into the locker room will be stored in the module with a unique id. To prove that the persons are authorized to enter that area, they need to scan their images. This scanner is interfaced with 8051 microcontroller. By using this controller we will be controlling the scanning process. After scanning has been completed, the person has to enter his unique id to open his locker with the help of a keypad. Immediately the locker will be opened. After the work has been completed, the locker will be closed again if a switch is pressed. If an unauthorized person tries to scan his image, then an indication will be given by a buzzer which is interfaced with the controller. If an authorized person forgets his id, he will be given 3 chances to re-enter the id. This project uses regulated 5V, 500mA power supply. 7805 three terminal voltage regulator is used for voltage regulation. Bridge type full wave rectifier is used to rectify the ac out put of secondary of 230/12V step down transformer.

Uploaded by

rockfloyd
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 26

FINGER PRINT BANK LOCKER

SYSTEM

Guided By:
Mr. R. Ram Prasad.
Asst.Professor

Presented By:

D. Bala krishna (04C51A0422)


V. Murali (05C51A0477)
B. Narendra (05C51A0
1
479)
N. Thrinath (05C51A0487)
OVERVIEW OF EXISTING SYSTEM

 Locks & Keys

 By this we can’t say that we


are going to provide good
security to our lockers.

2
DRAW BACKS OF PRESENT SYSTEM

 Security is less
 Others can steal the user’s entry key

3
Objective Of The Project

4
BLOCK DIAGRAM
Power POWER SUPPLY TO ALL SECTIONS
supply

16 X 2
LCD
Finger Print
Module 8
9
ULN
S DRIVER
Reset
5
2 Driver
Circuit
Stepper
Motor
Buzzer

5
Enter ur
fingerprint

verifiein
g
fingerpri no
nt

yes

Enter into the locker You are


room unauthorized
person

Enter password

Checking

Password no

yes
Locker is opened
by stepper
motor
6
Press Switch to
close the locker
Power supply
 Transformer

 Bridge Rectifier

 Regulator

7
MICROCONTROLLER

89S52 microcontroller.
 RAM 256Bytes.
 8Kb of flash memory.
 The functionality of 89S52 is
same as 8051
microcontroller.

8
FINGER PRINT MODULE

 In this we choose “verification” process.


 It can operate in 2 modes they are Master mode
and User mode.

9
MASTER MODE
 In this mode,we can register our finger image in
present of manager.

10
USER MODE
 Compare of input finger print and identified finger
print

11
LCD
 We are using 16x2 lcd display
 LCD has14 pin

12
13
PASSWORD PROTECTION

 Unique id (password) which is given to user to open


his locker with the help of a keypad
 Any port was used to handle our alpha-numeric
keypad.

14
15
STEPPER MOTOR

 Automatically, locker will open by stepper


motor(step angle).
 After the work by using reset pin user will secure
their locker.

16
17
Buzzer
 It is a signaling device.

 It beeps when user mismatch.

18
19
ADVANTAGES
 Most secure

 No manual errors

 Need not carry any


card

 Others cannot
steel the user’s
entry key
20
APPLICATIONS

 Voter Identification and electoral enrollment


 Industries
 Banks and ATM
 Personal Computer

21
SCOPE FOR ADVANCEMENTS

 GSM modem can be connected to this unit to communicate


to security department, in case of unauthorized entry trials.

22
CONCLUSION

 This project is used for 100 members, we can also extend


the capability for further requirements.
REFERENCE

Text Books:
Basics of Biometrics
-- David Louis
Website:
www.wikipedia.com
 Magazines:
Electronics for you

You might also like