Scribd
Upload
31 views

Transistorred Code Lock With Torch

This document describes an electronic lock circuit that opens with the connection of the correct combination of five switches out of twelve total switches. The circuit has three main sections: a power supply that regulates 12V DC power from mains AC, a control section with switches and a transistor relay, and a torch section with LEDs. To open the lock, the user connects the correct code combination of switches, which causes the transistor to energize the relay and open the door lock contacts. An additional switch enables a torch function with six LEDs for lighting.

Uploaded by

Fadli Fatur Rahmat
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
31 views

Transistorred Code Lock With Torch

This document describes an electronic lock circuit that opens with the connection of the correct combination of five switches out of twelve total switches. The circuit has three main sections: a power supply that regulates 12V DC power from mains AC, a control section with switches and a transistor relay, and a torch section with LEDs. To open the lock, the user connects the correct code combination of switches, which causes the transistor to energize the relay and open the door lock contacts. An additional switch enables a torch function with six LEDs for lighting.

Uploaded by

Fadli Fatur Rahmat
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

circuit

ideas
electroni cs for you March 2011 135 www. e f y Ma g . c o M
T
his electronic lock for domes-
tic use opens only when you
connect the right combination
of five switches. There are twelve
switches in total. If you connect a
wrong combination, the lock remains
closed. At night, fip switch S3 to on
position in order to enable the torch.
In the daytime, fip it back to off
position.
Fig. 1 shows the circuit of the tran-
sistorised code lock with torch. For
easy understanding, the entire circuit
can be divided in three sections: power
supply, control and torch.
The power supply section is built
around transformer X1, bridge recti-
fer comprising diodes D1 through
D4 and regulator IC 7812 (IC1). The
230V AC, 50Hz AC mains is stepped
down by transformer X1 to deliver
a secondary output of 15V, 250 mA.
The transformer output is rectifed
by the bridge rectifer, fltered by
capacitor C1 and regulated by IC1.
Capacitor C2 bypasses the ripples
present in the regulated supply.
When mains power is available, IC1
provides regulated 12V to the circuit
and power-on LED1 glows to indi-
cate that the circuit is enabled.
The control section is built around
switches S1 through S12, transistor T1
and relay RL1. Relay driver transistor
T1 is used to energise/de-energise the
relay.
The torch section is built around six
white LEDs (LED2 through LED7) and
resistors R3 and R4.
Working of the circuit is simple. To
open the door, you should know the
connection code. Here the connection
code is switches S1, S7, S2, S11 and S9.
This means you need to connect these
switches to each other by fipping them
to on position. As the connection
completes, transistor T1 conducts and
relay RL1 energises. As a result, the
S.C. DwiveDi
TranSiSToriSeD CoDe LoCk
wiTh TorCh
SUNIL KUMAR
door lock connected between the pole
and normally-open contacts of relay
RL1 opens.
If you connect a wrong combina-
tion, say, switches S4, S10, S11 and
S6, transistor T1 does not conduct and
relay RL1 remains de-energised. As a
result, the door lock remains closed.
Assemble the circuit on a general-
purpose PCB and house it in a small
cabinet. Fig. 2 shows the proposed
cabinet arrangement for switches and
LEDs. Install the cabinet at the front
door of your house.
As mentioned in the beginning,
switch S3 is used to enable the torch.
When it is fipped to on position, all
the LEDs (LED2 through LED7) glow.
Switches S4, S5, S6, S8, S10
and S12 are used just to con-
fuse the intruders and play no
role in opening the door.
You can also use a 12V
battery to power the circuit. In
that case, remove transformer
X1, diodes D1 through D4,
capacitor C1 and regulator IC2
(7812) and connect the battery
inside the cabinet with proper
polarity. Fig. 2: Proposed cabinet arrangement for switches and LEDs
Fig. 1: Circuit of transistorised code lock with torch

You might also like