Lenovo 3000 N200 Hardware Maintenance Manual

Lenovo 3000 N200 Hardware Maintenance Manual
May 2007 This manual supports: Lenovo 3000 N200 (MT 0687)
Lenovo 3000 N200 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under Notices on page 97.
First Edition (May 2007) Copyright Lenovo 2007. All rights reserved. U.S. GOVERNMENT USERS RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer SoftwareRestricted Rights at FAR 52.227-19, when applicable, or under Rights in Data-General, FAR 52.227.14 (Alternate III).
Contents
Introduction . . . . . . . . . . . . . 1
About this manual . . . . . . . . . . . Important service information . . . . . . . Strategy for replacing FRUs . . . . . . . . Strategy for replacing a hard disk drive . . . Important notice for replacing a system board . How to use error messages . . . . . . . Strategy for replacing FRUs for Custom Model Variant (CMV) products . . . . . . . . . Using PC Entitlement Warehouse (PEW) . . . Using eSupport . . . . . . . . . . . Using the HMM . . . . . . . . . . . Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . Diskette compatibility matrix . . . . . . . . Safety notices: multilingual translations . . . . Safety information . . . . . . . . . . . General safety . . . . . . . . . . . Electrical safety . . . . . . . . . . . Safety inspection guide . . . . . . . . Handling devices that are sensitive to electrostatic discharge . . . . . . . . . Grounding requirements . . . . . . . . Laser compliance statement . . . . . . . . . . . . . . . . . . 1 1 1 2 2 2 2 3 3 3 LCD-related symptoms . . . . . . . . Intermittent problems . . . . . . . . . Undetermined problems . . . . . . . . FRU replacement notices . . . . . . . . . Screw notices . . . . . . . . . . . . Retaining serial numbers . . . . . . . . Removing and replacing a FRU . . . . . . . 1010 Battery pack . . . . . . . . . . 1020 Hard disk drive slot cover . . . . . . 1030 Hard disk drive . . . . . . . . . 1040 DIMM slot cover . . . . . . . . . 1050 DIMM . . . . . . . . . . . . 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN . . . . . . . . . . . . 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN . . . . . . . . . . . . 1080 Optical drive . . . . . . . . . . 1090 Heat sink assembly slot cover . . . . 1100 Heat sink assembly . . . . . . . . 1110 CPU . . . . . . . . . . . . . 1120 Middle cover and function board . . . 1130 Keyboard . . . . . . . . . . . 1140 Keyboard bezel and fingerprint reader card 1150 Backup battery . . . . . . . . . 1160 Modem daughter card (MDC) . . . . 1170 Bluetooth daughter card (BDC) . . . . 1180 LCD unit . . . . . . . . . . . 1190 System board, 5-1 Digital Media Reader board, ExpressCard slot, and base cover . . . 2010 LCD front bezel . . . . . . . . . 2020 Inverter card . . . . . . . . . . 2030 LCD panel, LCD cable, and hinges . . . 2040 Camera and LCD rear cover assembly . . 2050 Wireless LAN antenna cables . . . . . Locations . . . . . . . . . . . . . . Front view. . . . . . . . . . . . . Rear view . . . . . . . . . . . . . Bottom view . . . . . . . . . . . . Parts list . . . . . . . . . . . . . . Overall . . . . . . . . . . . . . . LCD FRUs . . . . . . . . . . . . . Keyboard . . . . . . . . . . . . . Recovery discs . . . . . . . . . . . Corel software CDs . . . . . . . . . . AC adapters . . . . . . . . . . . . Miscellaneous parts . . . . . . . . . . Common parts list . . . . . . . . . . Notices . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 39 40 40 41 41 41 44 45 46 46 47 48
. 4 . 5 . 5 . 11 . 11 . 11 . 13 . 14 . 14 . 15
. 49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 51 52 53 55 56 58 60 64 65 66 67 69 72 73 74 76 77 79 79 80 80 81 82 87 89 90 94 94 95 95 97 98
General descriptions . . . . . . . . . 17
Read this first . . . . . . . . . . . . What to do first . . . . . . . . . . . Related service information . . . . . . . . Service Web site . . . . . . . . . . . Restoring the factory contents by using Product Recovery discs . . . . . . . . . . . Passwords . . . . . . . . . . . . . Power management . . . . . . . . . Checkout guide . . . . . . . . . . . . Testing the computer . . . . . . . . . Detecting system information with PC-Doctor . Power system checkout . . . . . . . . . . . . . . . . . . . 17 17 19 19 19 20 22 24 24 26 26
Lenovo 3000 N200 . . . . . . . . . . 29

Product overview . . Specifications . . . Status indicators . . FRU tests . . . . Fn key combinations Symptom-to-FRU index Numeric error codes Error messages . . Beep symptoms . . No-beep symptoms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 30 32 33 34 35 35 37 38 38
Copyright Lenovo 2007
iii
iv
MT 0687
Introduction
About this manual
This manual contains service and reference information for Lenovo 3000 N200 (MT 0687). Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers. v The product-specific section includes service, reference, and product-specific parts information.
Important This manual is intended for trained service personnel who are familiar with Lenovo 3000 products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a Lenovo 3000 product, be sure to review the safety information under Safety notices: multilingual translations on page 5, Safety information on page 11, and Laser compliance statement on page 15.
Important service information

Important BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/ support Advise customers to contact the Customer Support Center at 800-426-7378 if they need assistance in obtaining or installing any software fixes, drivers, and BIOS downloads. Customers in Canada should call the Customer Support Center at 800-565-3344 for assistance or download information.
Strategy for replacing FRUs

Before replacing parts Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:

v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.
Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: v Do not drop a system board or apply any excessive force to it. v Avoid rough handling of any kind. v Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
How to use error messages

Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU Index for the computer you are servicing.
Strategy for replacing FRUs for Custom Model Variant (CMV) products
Custom Model Variant (CMV) is a unique configuration that has been negotiated between LenovoTM and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special bid offering. Therefore, it is NOT generally announced. There are three information resources to identify which FRUs are used to support CMV products. These sources are PC Entitlement Warehouse (PEW), eSupport, and the HMM.
MT 0687
Using PC Entitlement Warehouse (PEW)

v PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CMV products at a MT - serial number level. An example of key commodities are hard disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory. v Remember, all CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where model = fixed part number. v PEW can be accessed at the following Web site: http://w3-3.ibm.com/pc/entitle Customers can also access PEW via http://www-307.ibm.com/pc/support/site.wss/product.do?template=/ warranty/warranty.vm&sitestyle=lenovo Click on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.com
Using eSupport
For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) v eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW). v eSupport can be accessed at the following Web site: http://www.lenovo.com/ support v To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP. Type in the model type and serial number. The key commodities will be returned in the eSupport record under PARTS SHIPPED WITH YOUR SYSTEM. For the Remaining FRUs (the complete list of FRUs at the MT Model level) v eSupport can be used to view the complete list of FRUs for a machine type and model. v To view the complete list of FRUs, type in the machine type and model (Example: 1829-CTO) under QUICK PATH. Under View by Document Type select PARTS INFORMATION. Under Filter by Category select SERVICE PARTS. Under Parts Information by Date select SYSTEM SERVICE PARTS. The list of service parts by description, with applicable machine type model and FRU will be displayed.
Using the HMM

Use the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level. CMVs are custom models and are not found in the HMM.
Introduction
Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. So, if the original FRU parts are non compliant, replacement parts can also be non compliant. In all cases if the original FRU parts are RoHS compliant the replacement part must also be RoHS compliant. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo's requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs. RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006 Current or original part Non-RoHS Non-RoHS Non-RoHS RoHS Replacement FRU Can be Non-RoHS Can be RoHS Can sub to RoHS Must be RoHS Products marketed after June 2006 Current or original part Must be RoHS Replacement FRU Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order.
MT 0687
Diskette compatibility matrix
Diskette compatibility matrix

The compatibility of each of the drives with the diskettes for it is as follows:
Diskette drive 3.5-inch Diskette capacity 1.0 MB 2.0 MB 4.0 MB Compatibility Read and write Read and write Not compatible
Safety notices: multilingual translations

In this manual, safety notices appear in English with a page number reference to the appropriate multilingual, translated safety notice found in this section. The following safety notices are provided in English, French, German, Hebrew, Italian, and Spanish. Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre lordinateur sous tension aprs remplacement dune unit en clientle, vrifiez que tous les ressorts, vis et autres pices sont bien en place et bien fixes. Pour ce faire, secouez lunit et assurez-vous quaucun bruit suspect ne se produit. Des pices mtalliques ou des copeaux de mtal pourraient causer un court-circuit. Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, mu sichergestellt werden, da keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehuse vergessen wurden. Der Computer mu geschttelt und auf Klappergerusche geprft werden. Metallteile oder-splitter knnen Kurzschlsse erzeugen.
Prima di accendere lelaboratore dopo che stata effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse allinterno dellelaboratore. Verificare ci scuotendo lelaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi. Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y dems piezas pequeas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Comprubelo agitando el sistema y escuchando los posibles ruidos que provocaran. Las piezas metlicas pueden causar cortocircuitos elctricos.
Introduction
Safety notices
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les dmontez pas, ne les rechargez pas, ne les exposez ni au feu ni leau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de lhorloge temps rel, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. Une batterie ou une pile inapproprie risque de prendre feu ou dexploser. Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die Batterie kann schwere Verbrennungen oder Vertzungen verursachen. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nellacqua n cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dellRTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa. Algunas bateras de reserva contienen una pequea cantidad de nquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.
MT 0687
Safety notices
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la dmontez pas, ne lexposez ni au feu ni leau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la batterie, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. En effet, une batterie inapproprie risque de prendre feu ou dexploser. Akkus enthalten geringe Mengen von Nickel. Sie drfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
La batteria contiene piccole quantit di nichel. Non smontarla, gettarla nel fuoco o nellacqua n cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa. Las bateras contienen pequeas cantidades de nquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas al sustituir la batera. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.
Introduction
Safety notices
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100C (212F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle prsente des risques dincendie, dexplosion ou de brlures graves. Ne la rechargez pas, ne retirez pas son connecteur polaris et ne la dmontez pas. Ne lexposez pas une temperature suprieure 100C, ne la faites pas brler et nen exposez pas le contenu leau. Mettez la pile au rebut conformment la rglementation en vigueur. Une pile inapproprie risque de prendre feu ou dexploser. Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entznden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs drfen nicht aufgeladen, zerlegt, ber 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa. La batera de repuesto es una batera de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100C (212F), ni la incinere ni exponga el contenido de sus celdas al agua. Deschela tal como dispone la normativa local.
MT 0687
Safety notices
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau daffichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un mdecin si des symptmes persistent aprs le lavage. Die Leuchtstoffrhre im LCD-Bildschirm enthlt Quecksilber. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgem behandelt wird oder der Computer auf den Boden fllt. Wenn der Bildschirm beschdigt ist und die darin befindliche Flssigkeit in Kontakt mit Haut und Augen gert, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesplt und bei Beschwerden anschlieend ein Arzt aufgesucht werden.
Nel caso che caso lLCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere. Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las reas afectadas con agua durante 15 minutos como mnimo. Obtenga atencin medica si se presenta algn sntoma del fluido despues de lavarse.
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin dviter tout risque de choc lectrique, ne retirez pas le cache en plastique protgeant la partie infrieure de la carte dalimentation. Aus Sicherheitsgrnden die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore. Para evitar descargas, no quite la cubierta de plstico que rodea la parte baja de la tarjeta invertida.
Introduction
Safety notices
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu lev, le court-circuit ou la mise la masse dune batterie peut produire suffisamment de courant pour brler des matriaux combustibles ou causer des brlures corporelles graves. Obwohl Hauptbatterien eine niedrige Spannung haben, knnen sie doch bei Kurzschlu oder Erdung genug Strom abgeben, um brennbare Materialien zu entznden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione. Aunque las bateras principales tienen un voltaje bajo, una batera cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unit remplaable en clientle, mettez le systme hors tension, dbranchez tous les cordons dalimentation des socles de prise de courant, retirez la batterie et dconnectez tous les cordons dinterface. Die Stromzufuhr mu abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione. Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente elctrica, quite la batera y, a continuacin, desconecte cualquier cable de conexin entre dispositivos.
10
MT 0687
Safety information
Safety information
The following section presents safety information with which you need to be familiar before you service a Lenovo 3000 computer.
General safety
Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. v Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe. v Before you start the machine, make sure that other service representatives and the customers personnel are not in a hazardous position. v Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine. v Keep your toolcase away from walk areas so that other people will not trip over it. v Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. v Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8 centimeters (3 inches) from the end. v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Attention: Metal objects are good electrical conductors. v Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. v After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer. v Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
Introduction
11
Safety information
Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. v Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. v Do not work alone under hazardous conditions or near equipment that has hazardous voltages. v Disconnect all power before: Performing a mechanical inspection Working near power supplies Removing or installing main units v Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position. v If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power, if necessary. Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body. When using testers, set the controls correctly and use the approved probe leads and accessories for that tester. Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages. Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check that it has been powered off. Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
v v v v
12
MT 0687
Safety information
v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generators and similar units. (This practice ensures correct grounding of the units.) v If an electrical accident occurs: Use caution; do not become a victim yourself. Switch off power. Send another person to get medical aid.
Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo 3000 features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: v Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock) v Explosive hazards, such as a damaged CRT face or a bulging capacitor v Mechanical hazards, such as loose or missing hardware To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected. Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Power off the computer. Disconnect the power cord. 3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground. b. The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-Lenovo 3000 alterations. Use good judgment as to the safety of any non-Lenovo 3000 alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. 8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Introduction
13
Safety information
Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Notes 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: v Keep the parts in protective packages until they are inserted into the product. v Avoid contact with other people. v Wear a grounded wrist strap against your skin to eliminate static on your body. v Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. v Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. v Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.
Note The use of a grounding system to guard against ESD damage is desirable but not necessary. Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
14
MT 0687
Laser compliance statement

Some models of Lenovo 3000 computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products. If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following:
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposio radiao.
Pour viter tout risque dexposition au rayon laser, respectez les consignes de rglage et dutilisation des commandes, ainsi que les procdures dcrites. Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefhrliche Laserstrahlung auftreten.
Lutilizzo di controlli, regolazioni o lesecuzione di procedure diverse da quelle specificate possono provocare lesposizione a.
El uso de controles o ajustes o la ejecucin de procedimientos distintos de los aqu especificados puede provocar la exposicin a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open.
Introduction
15

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiao por raio laser ao abrir. No olhe fixo no feixe de luz, no olhe diretamente por meio de instrumentos ticos e evite exposio direta com o feixe de luz.
Rayonnement laser si carter ouvert. vitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon. Laserstrahlung bei geffnetem Gert. Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden. Kinyitskor lzersugr ! Ne nzzen bele se szabad szemmel, se optikai eszkzkkel. Kerlje a sugrnyalbbal val rintkezst ! Aprendo lunit vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare lesposizione diretta al fascio.
Radiacin lser al abrir. No mire fijamente ni examine con instrumental ptico el haz de luz. Evite la exposicin directa al haz.
16
MT 0687
General descriptions
The descriptions in this chapter apply to any Lenovo 3000 model that has the PC-Doctor for DOS diagnostics program. Some descriptions might not apply to your particular computer.
Read this first

Before you go to the checkout guide, be sure to read this section.
Important notes v Only certified trained personnel should service the computer. v Before replacing any FRU, read the entire page on removing and replacing FRUs. v When you replace FRUs, use new nylon-coated screws. v Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten. v Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model of the machine and the FRU part number are correct by referring to the FRU parts list. v A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do not replace the FRU. v Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8. Machine type, model number, and serial number __ 9. Customers name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer.
17
Read this first

Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use. Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list: The following are not covered under warranty: v LCD panel cracked from the application of excessive force or from being dropped v Scratched (cosmetic) parts v Distortion, deformation, or discoloration of the cosmetic parts v Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force v Damage caused by liquid spilled into the system v Damage caused by the improper insertion of a PC Card or the installation of an incompatible card v Improper disc insertion or use of an optical drive v Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels v Damaged or bent diskette eject button v Fuses blown by attachment of a nonsupported device v Forgotten computer password (making the computer unusable) v Sticky keys caused by spilling a liquid onto the keyboard v Use of an incorrect ac adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities: v Missing parts might be a symptom of unauthorized service or modification. v If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped.
18
MT 0687
Related service information

This section provides information about the following: v Service Web site v Restoring the factory contents by using Product Recovery discs v Passwords on page 20 v Power management on page 22
Service Web site

When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/spm
Restoring the factory contents by using Product Recovery discs

When the hard disk drive is replaced because of a failure, no Product Recovery program is on the new hard disk. In this case, you must use the recovery disc for the computer. Order the recovery disc and the hard disk drive at the same time so that you can recover the new hard disk drive with the preinstalled software when they arrive. For information on which disc to order, see Recovery discs on page 90. To install the factory contents by using Product Recovery discs, do the following:
Note The recovery process might take up to 2 hours. 1. Make the optical drive the first start up device in the startup sequence. 2. Insert the bootable Rescue and Recovery Startup disc into the optical drive, and then start the computer. 3. In the Rescue and Recovery workspace, complete the following procedure: a. When the Rescue and Recovery workspace opens, click Continue on the Welcome window and then click Restore your system. b. When a message about accessing a USB device is displayed, click OK. c. In the initial window of the Restore your system wizard, select Restore my hard drive to the original factory state and click Next. d. In the next window, select I do not want to save any files and click Next. e. A warning opens not to turn off the computer during the recovery process. Click OK. 4. When the Product Recovery window opens, click OK. 5. The Terms and Conditions window opens, select I accept these terms and conditions and then click OK. 6. After the files necessary for the product recovery are copied from the Rescue and Recovery Startup disc to the hard drive, the system restarts automatically and boot back into Rescue and Recovery. Remove the disc and turn off the computer. 7. Turn on the computer to continue the recovery process. 8. After you restart the computer, the computer prompts you for a supplemental Rescue and Recovery disc. If you have a supplemental Rescue and Recovery disc, click OK and insert the supplemental disc. If you do not have a supplemental disc, click No.
19

9. When prompted, insert the appropriate Product Recovery disc and then click OK. The second phase of the recovery process begins. 10. When all of the data has been copied from the last Product Recovery disc in the set, a message is displayed prompting you to restart the computer. Remove the disc and then click Yes, then a message is displayed asking you to continue the recovery process. Click Continue to restart your computer, then the computer restarts and the third phase of the recovery process begins. 11. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup.
Passwords
As many as three passwords may be needed for any Lenovo 3000 computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted. Power-on password: A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted. Hard-disk password: There are two hard-disk passwords (HDPs): v User HDPfor the user v Master HDPfor the system administrator, who can use it to get access to the hard disk even if the user has changed the user HDP Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user. Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized servicers provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. Supervisor password: A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration. Attention: If the SVP has been forgotten and cannot be made available to the servicer, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee.
20
MT 0687
How to remove the power-on password

To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see 1010 Battery pack on page 45. 3. Remove the backup battery. For how to remove the backup battery, see 1150 Backup battery on page 64. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5. Reinstall the backup battery and the battery pack. (B) If an SVP has been set and is known by the servicer: 1. Turn on the computer; then, while the initial screen is displayed, press the Lenovo CareSM button. The Rescue and Recovery screen opens. 2. Click Access BIOS. The System Restart Required window is displayed. 3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens. 4. Select Security, using the cursor directional keys to move down the menu. 5. Select Password. 6. Select Power-On Password*1. 7. Type the current SVP in the Enter Current Password field. Then leave the Enter New Password field blank, and press Enter twice. 8. In the Changes have been saved window, press Enter. 9. Press F10; then, in the Setup confirmation window, select Yes . Note: For some models, the BIOS menu marked *1 is User Password.
How to remove the hard-disk password

Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the servicer, neither Lenovo nor Lenovo authorized servicers provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the following: 1. Turn on the computer; then, while the initial screen is displayed, press the Lenovo Care button. The Rescue and Recovery screen opens. 2. Click Access BIOS. The System Restart Required window is displayed. 3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens. 4. Select Security, using the cursor directional keys to move down the menu. 5. Select Password. 6. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. 7. Select Master HDP. 8. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 9. Press F10.
21

10. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed.
Power management
Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation.
Screen blank mode

If the time set on the Turn off monitor timer in the operating system expires, the LCD backlight turns off. To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode

When the computer enters sleep (standby) mode, the following events occur in addition to what occurs in screen blank mode: v The LCD is powered off. v The hard disk drive is powered off. v The CPU stops. To enter sleep (standby) mode, press Fn+F4. In certain circumstances, the computer goes into sleep (standby) mode automatically: v If a suspend time has been set on the timer, and the user does not do any operation with the keyboard, the hard disk, the parallel connector, or the diskette drive within that time. v If the battery indicator blinks orange, indicating that the battery power is low. (Alternatively, if Hibernate when battery becomes low has been selected in the Power Management Properties window, the computer goes into hibernation mode.) To cause the computer to return from sleep (standby) mode and resume operation, do one of the following: v Press the Fn key. v Open the LCD cover. v Turn on the power switch. Also, in the following event, the computer automatically returns from sleep (standby) mode and resumes operation: v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a few seconds before taking any action to reenter operation mode.
Hibernation mode
In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off. To cause the computer to enter hibernation mode, do any of the following:
22
MT 0687

v Press the Fn+F12 keys. v If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action. Closing the lid. Pressing the power button. Also, the computer goes into hibernation mode automatically in either of the following conditions: v If a hibernation time has been set on the timer, and if the user does not do any operation with the keyboard, the hard disk drive, the parallel connector, or the diskette drive within that time. v If the timer conditions are satisfied in suspend mode. When the power is turned on, the computer returns from hibernation mode and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive.
23
Checkout guide
Checkout guide
Use the following procedures as a guide in identifying and correcting problems with the Lenovo 3000 computer. Note: The diagnostic tests are intended to test only Lenovo 3000 products. The use of non-Lenovo 3000 products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the operation.
Testing the computer

The Lenovo 3000 computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to Product overview on page 30. For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by use of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter. Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is available on the following Web site: http://www.lenovo.com/support
Creating the PC-Doctor diagnostics diskette

To create the PC-Doctor disk from the Rescue and Recovery workspace , do as follows: 1. Enter the Rescue and Recovery workspace by pressing the Lenovo Care button during POST. 2. When the Rescue and Recovery workspace finishes loading, click Diagnostic Diskette. 3. Authenticating the digital signature takes about 15 seconds; then the Lenovo 3000 computer will reboot into PC-DOS. 4. A batch file automatically starts up to prompt you through the process of creating diskettes. You are notified of how many diskettes you will need. a. You are prompted to insert each diskette in sequence. b. Typically, all you need to do is to press the Enter key for the floppy drive; the system then formats and creates the diskette. c. Each diskette is erased and formatted with the PC-Doctor for DOS boot image. 5. Once all the diskettes have been created, the Lenovo 3000 computer will reboot. The user is asked to remove all diskettes from the drive, or to insert the first diskette created if it is desired to run the diagnostics.
24
MT 0687
Checkout guide
To run the test, do as follows: 1. Insert the PC-Doctor disk into the diskette drive; then power on the computer. If the computer cannot be powered on, go to Power system checkout on page 26, and check the power sources. If an error code appears, go to Symptom-to-FRU index on page 35. On the first screen, select the model and press Enter. Follow the instructions on the screen. 2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu.
Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Fixed Disks Diskette Drives Memory Test - Full Memory Test - Quick
PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows: Diagnostics v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Fixed Disks Diskette Drives Memory Test Full Memory Test Quick Interactive Tests v v v v Keyboard Video Mouse System Load
Notes: v In the Keyboard test in Interactive Tests, the Fn key should be held down with M key for at least 2 seconds; otherwise, it cannot be sensed. v Video Adapter test supports only the LCD display on the Lenovo 3000 computer. If you have an external monitor attached to your computer, detach it before running PC-Doctor for DOS. 4. Run the applicable function test. 5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it. 6. To exit the test, select Quit Exit Diag. To cancel the test, press Esc. Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.
25
Checkout guide
Detecting system information with PC-Doctor

PC-Doctor can detect the following system information:
Hardware Info
v v v v v v v v v v v System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive
Utility
v v v v v v v v v v v
PC-Doctor for Windows

This product is designed to help you troubleshoot and resolve problems related to your computer. Select one of the categories listed below to display symptoms and solutions: v CHECK SYSTEM HEALTH v SYSTEM AND DEVICE TESTS v LENOVO TROUBLESHOOTING v CENTER v SYSTEM REPORTS v UPDATES AND SUPPORT
Power system checkout

To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts: v Checking the ac adapter on page 27 v Checking operational charging on page 27 v Checking the battery pack on page 27
26
MT 0687
Checkout guide
Checking the ac adapter

You are here because the computer fails only when the ac adapter is used. v If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation. v If the computer does not charge during operation, go to Checking operational charging. To check the ac adapter, do the following: 1. Unplug the ac adapter cable from the computer. 2. Measure the output voltage at the plug of the ac adapter cable. See the following figure:
Pin 1
Voltage (V dc) +20 0 Ground
3 2 1 (20V)
2 3
Note: Output voltage of pin no.2 of the ac adapter may be different from the one you are servicing. 3. If the voltage is not correct, replace the ac adapter. 4. If the voltage is acceptable, do the following: v Replace the system board. v If the problem persists, go to Product overview on page 30. Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging

To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack. If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack

Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment (but do not click), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.
27
Checkout guide
Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it. To check the battery pack, do the following: 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (). See the following figure:
Terminal
Voltage (V dc) + 0 to + 12.6 Ground ()
1(+)
3 2(+)
7(-) 6(-)
1 7
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged. Note: Recharging will take at least 3 hours, even if the indicator does not turn on. If the voltage is still less than +11.0 V dc after recharging, replace the battery. 4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 4 and 7. The resistance must be 4 to 30 K . If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board.
28
MT 0687
Lenovo 3000 N200

Product overview . . . . . . . . . . . . Specifications . . . . . . . . . . . . . Status indicators . . . . . . . . . . . . FRU tests . . . . . . . . . . . . . . Fn key combinations . . . . . . . . . . Symptom-to-FRU index . . . . . . . . . . Numeric error codes . . . . . . . . . . Error messages . . . . . . . . . . . . Beep symptoms . . . . . . . . . . . . No-beep symptoms . . . . . . . . . . . LCD-related symptoms . . . . . . . . . Intermittent problems . . . . . . . . . . Undetermined problems . . . . . . . . . FRU replacement notices . . . . . . . . . . Screw notices . . . . . . . . . . . . . Retaining serial numbers . . . . . . . . . Restoring the serial number of the system unit Retaining the UUID . . . . . . . . . Reading or writing the ECA information . . Removing and replacing a FRU . . . . . . . . 1010 Battery pack . . . . . . . . . . . 1020 Hard disk drive slot cover . . . . . . . 1030 Hard disk drive . . . . . . . . . . 1040 DIMM slot cover . . . . . . . . . . 1050 DIMM . . . . . . . . . . . . . 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN . . . . . . . . . . . . . 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN . . . . . . . . . . . . . 1080 Optical drive . . . . . . . . . . . 1090 Heat sink assembly slot cover . . . . . 1100 Heat sink assembly . . . . . . . . . 1110 CPU . . . . . . . . . . . . . . 1120 Middle cover and function board . . . . 1130 Keyboard . . . . . . . . . . . . 30 30 32 33 34 35 35 37 38 38 39 40 40 41 41 41 42 42 42 44 45 46 46 47 48 49 50 51 52 53 55 56 58 1140 Keyboard bezel and fingerprint reader card 1150 Backup battery . . . . . . . . . . 1160 Modem daughter card (MDC) . . . . . 1170 Bluetooth daughter card (BDC) . . . . . 1180 LCD unit . . . . . . . . . . . . 1190 System board, 5-1 Digital Media Reader board, ExpressCard slot, and base cover . . . . 2010 LCD front bezel . . . . . . . . . . 2020 Inverter card . . . . . . . . . . . 2030 LCD panel, LCD cable, and hinges . . . . 2040 Camera and LCD rear cover assembly . . . 2050 Wireless LAN antenna cables . . . . . . Locations . . . . . . . . . . . . . . . Front view. . . . . . . . . . . . . . Rear view . . . . . . . . . . . . . . Bottom view . . . . . . . . . . . . . Parts list . . . . . . . . . . . . . . . Overall . . . . . . . . . . . . . . . LCD FRUs . . . . . . . . . . . . . . 14.1-in. WXGA TFT . . . . . . . . . . Keyboard . . . . . . . . . . . . . . Recovery discs . . . . . . . . . . . . Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Basic (32 bit) DVDs . . Windows Vista Business (32 bit) DVDs . . . Windows Vista Ultimate (32 bit) DVDs . . . Corel software CDs . . . . . . . . . . . AC adapters . . . . . . . . . . . . . Miscellaneous parts . . . . . . . . . . . Common parts list . . . . . . . . . . . Tools . . . . . . . . . . . . . . Power cords . . . . . . . . . . . . Notices . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . 60 64 65 66 67 69 72 73 74 76 77 79 79 80 80 81 82 87 87 89 90 90 91 92 93 94 94 95 95 95 96 97 98
29
Product overview
Product overview
This section presents the following productunique information: Specifications Status indicators on page 32 FRU tests on page 33 Fn key combinations on page 34
Specifications
The following table lists the specifications of the Lenovo 3000 N200:
Feature Processor
Description
Intel Celeron M processor 540 (1.86 GHz), 1MB L2

Intel Core 2 Duo processor T7100 (1.8GHz), 2MB L2

cache (533 MHz)
Bus architecture
cache (800 MHz) Intel Core 2 Duo processor T7300 (2.0 GHz), 4MB L2 cache (800 MHz) IntelCore2DuoprocessorT7500(2.2GHz),4MBL2 cache(800MHz) IntelCeleronprocessor530(1.73GHz533MHz1MBL2) IntelCeleronprocessor550(2.0GHz533MHz1MBL2) IntelCore2DuoprocessorT5550(1.83GHz667MHz2MBL2) IntelCore2DuoprocessorT2330(1.6GHz533MHz1MBL2) IntelCore2DuoprocessorT2310(1.46GHz533MHz1MBL2) 667MHz PSB 667MHz DDR2 SDRAM (PC25300) HUB link PCI bus LPC bus PCI Express bus
Graphic memory chip Display Standard memory
Intel 965GM NVIDIA G72MV (GO 7300) 14.1inch wide, 16M colors, WXGA(1280 768 resolution) TFT color LCD 512MB DDR2667 SDRAM SODIMM (PC25300) card 1 512MB DDR2667 SDRAM SODIMM (PC25300) card 2 1GB DDR2667 SDRAM SODIMM (PC25300) card 1 2GB DDR2667 SDRAM SODIMM (PC25300) card 1 512MB DDR2667 SDRAM SODIMM (PC25300) card 1 1GB DDR2667 SDRAM SODIMM (PC25300) card 1 2GB DDR2667 SDRAM SODIMM (PC25300) card 1 (maximum of 2.0 GB) 242 bytes 60 GB, 5400 rpm, 9.5 mm high, SATA interface 80 GB, 5400 rpm, 9.5 mm high, SATA interface 120 GB, 5400 rpm, 9.5 mm high, SATA interface 160 GB, 5400 rpm, 9.5 mm high, SATA interface
Optional memory
CMOS RAM Hard disk drive
Supported hard disk drives are depend on the model. Optical drive DVD/CDRW combo drive, 12.7 mm high DVDRAM/RW drive, 12.7 mm high
(continued)
30
MT 0687
Product overview
Feature I/O port Description 5-1 Digital Media Reader External monitor connector Stereo headphone jack Monaural microphone jack RJ11 connector RJ45 connector TV-out connector (S-Video) Universal serial bus (USB) connector 4 (compatible with USB 1.1 and 2.0) v IEEE 1394 connector v v v v v v v v v 56.6 Kbps v Built-in stereo speakers v Software control volume v 10/100 Ethernet v Intel PRO Wireless 3945ABG Mini-PCI Express Adapter v Broadcom 802.11bg WLAN PCI-E Mini Card v Lenovo 11a/b/g/n Wireless LAN Mini-PCI Express Adapter v Intel Wireless WiFi Link 4965AGN v ExpressCard slot v Bluetooth daughter card v AMoM, 56 kbps V.92 Yes v Li-ion battery (6 cells) 2.4 Ah v 65-watt (20 V) slim type v 90-watt (20 V) type v v v v Windows Windows Windows Windows Vista Home Premium (32 bit) Vista Home Basic (32 bit) Vista Business (32 bit) Vista Ultimate (32 bit)
Internal modem Audio Ethernet (on the system board) Mini PCI adapter
ExpressCard slot Bluetooth wireless (some models) Modem Touch pad Battery AC adapter Preinstalled operating system
Lenovo 3000 N200
31
Product overview
Status indicators
The system status indicators show the status of the computer, as follows:
1 2 3 4 5
Indicator 1 Caps lock
Meaning Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in uppercase without pressing the Shift key. To enable or disable Caps Lock mode, press the CapsLk key. The numeric keypad on the keyboard is enabled. To enable or disable the keypad, press and hold the Fn key, and press the NmLk key. A card in the 5-1 Digital Media Reader is being used to read and write data. When this indicator is blinking, do not put the computer into sleep (standby) mode, remove the card from the slot, or turn off the computer. Green: Data is being read from or written to the hard disk drive. When this indicator is on, do not put the computer into sleep (standby) mode or turn off the computer. Note: Do not move the system while the green drive-in-use light is on. Sudden physical shock could cause drive errors. Green: The computer is on and ready to use. This indicator stays lit whenever the computer is on and is not in sleep (standby) mode.
Num lock
5-1 Digital Media Reader status
Drive in use
Power on
(continued)
32
MT 0687
Product overview
Indicator 6 Wireless status Meaning Green: The wireless feature (the IEEE 802.11 standard or the IEEE802.11n) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 0% to 80% of the capacity. Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged. Orange: The battery is charged between 5% and 20% of the capacity, and being discharged. Blinking orange (slow): The battery is charged between 5% to 20% of the capacity, and being charged. Blinking orange (rapid): The battery is charged between 0% to 5% of the capacity. Green: The computer is in sleep (standby) mode. Blinking green: The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation.
Bluetooth status
R
Battery status
Sleep (standby) status
FRU tests
The following table shows the test for each FRU.
FRU System board LCD unit Keyboard Hard disk drive Diskette drive Memory Applicable test 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 1. Diagnostics --> Video Adapter 2. Interactive Tests --> Video 1. Diagnostics --> Systemboard --> Keyboard 2. Interactive Tests --> Keyboard Diagnostics --> Fixed Disks v Diagnostics --> Diskette Drives 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Memory TestQuick. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. 3. If the test does not detect the error, run Diagnostics --> Memory TestFull.
Lenovo 3000 N200
33
Product overview
Fn key combinations
The following table shows the function of each combination of Fn with a function key.
Key combination Description Fn+F1 Fn+F2 Fn+F3 Fn+F4 Fn+F5 Volume down. Volume up. Reserved. Put the computer in sleep (standby) mode. To return to normal operation, press the Fn key only, without pressing a function key. Enable or disable the built-in wireless networking features and the Bluetooth features. If you press Fn+F5, a list of wireless features is displayed. You can quickly change the power state of each feature in the list. Reserved. Open the window for Choose Presentation or Display scheme. If you press this combination of keys, a list of schemes is displayed in the window. You can quickly select a scheme in the list. Reserved. Reserved. Make the computer display less bright. Make the computer display brighter. Put the computer into hibernation mode. To return to normal operation, press the power button. Mute the sound from the computer. Scroll Lock (ScrLk). Numeric Lock (NmLk) Has the same function as the SysRq key. Has the same function as the Break key. Has the same function as the Home key. Has the same function as the End key. These key combinations work with Windows Media Player. Fn+down arrow key works for the Play or Pause button, Fn+up arrow key for the Stop button, Fn+right arrow key for the Next Track button, and Fn+left arrow key for the Previous Track button.
Fn+F6 Fn+F7
Fn+F8 Fn+F9 Fn+F10 Fn+F11 Fn+F12 Fn+Esc Fn+Insert Fn+Delete Fn+PrtSc Fn+Pause Fn+PgUp Fn+PgDn Fn+cursor keys
34
MT 0687
Symptom-to-FRU index
The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed FRU or action, in sequence. If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU. This index can also help you determine, during regular servicing, what FRUs are likely to need to be replaced next. A numeric error is displayed for each error detected in POST or system operation. In the displays, n can be any number. If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not described there, go to Intermittent problems on page 40.
Note For a device not supported by diagnostic codes in the Lenovo 3000 notebook computers, see the manual for that device.
Numeric error codes

Symptom or error 0200 Failure Fixed Disk FRU or action, in sequence 1. Reseat the hard disk drive. 2. Load Setup Defaults in BIOS Setup Utility. 3. Hard disk drive. 4. System board. 1. Keyboard. 2. System board. Load Setup Defaults in BIOS Setup Utility.
021x Keyboard error 0220 Monitor type does not match CMOSRun SETUP 0230 Shadow RAM Failed at offset:nnnn 0231 System RAM Failed at offset:nnnn 0232 Extended RAM Failed at offset:nnnn 0250 System battery is deadReplace and run SETUP
System board. 1. DIMM. 2. System board. 1. DIMM. 2. System board. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251 System CMOS checksum badDefault configuration use
Lenovo 3000 N200
35
Symptom or error 0260 System timer error FRU or action, in sequence 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board. 1. Load Setup Default in BIOS Setup Utility. 2. DIMM. 3. System board. 1. Load Setup Defaults in BIOS Setup Utility. 2. Replace the backup battery. 3. System board. 1. DIMM. 2. System board. 1. DIMM. 2. System board. 1. DIMM. 2. System board.
0270 Real time clock error
0280 Previous boot incomplete Default configuration used 02F4 EISA CMOS not writable
02F5 DMA test failed 02F6 Software NMI failed 02F7 Fail-safe timer NMI failed
36
MT 0687
Error messages
Symptom or error Unsupported memory. Device address conflict. FRU or action, in sequence DIMM. Make sure to use supported memory. 1. Load Setup Defaults in the BIOS Setup Utility. 2. Backup battery. 3. System board. 1. Load Setup Defaults in the BIOS Setup Utility. 2. Backup battery. 3. System board. 1. DIMM. 2. System board. 1. DIMM. 2. System board. 1. Load Setup Defaults in the BIOS Setup Utility. 2. Backup battery. 3. System board. 1. Restore the system configuration to what it was before the computer entered hibernation mode. 2. If memory size has been changed, re-create the hibernation file. 1. Fan. 2. Thermal grease. 3. System board. System board. The Predesktop Area in the HDD is corrupted. Restore it from a recovery disc. Check the status of device which you want to boot from. Device not found. 1. The device you want to boot from. 2. System board. Device Error. 1. The device you want to boot from. 2. System board. No valid operating system. 1. Check that the operating system has no failure and is installed correctly. 2. Reinstall the operation system. Excluded from boot order. v Enter the BIOS Setup Utility and add the device in boot order.
Allocation error for device.
Failing bits: nnnn. Invalid system configuration data. I/O device IRQ conflict.
Hibernation error.
Fan error.
Thermal sensing error. Authentication of system services failed. Press <Esc> to resume. Cannot boot from any device.
Lenovo 3000 N200
37
Beep symptoms
Symptom or error One beep and a blank, unreadable, or flashing LCD. FRU or action, in sequence 1. 2. 3. 4. Reseat the LCD connector. LCD assembly. External CRT. System board.
One long and two short beeps, and a blank or unreadable LCD. Two short beeps with error codes. Two short beeps and a blank screen. Three short beeps, pause, three more short beeps, and one short beep. One short beep, pause, three short beeps, pause, three more short beeps, and one short beep. Only the cursor appears. Four cycles of four short beeps and a blank screen. Five short beeps and a blank screen.
1. System board. 2. LCD assembly. 3. DIMM. POST error. See Numeric error codes on page 35. 1. System board. 2. DIMM. 1. DIMM. 2. System board
Reinstall the operating system. System board (security chip) System board
No-beep symptoms
Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is and no POST. connected tightly and correctly. 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST. The power-on password prompt appears. 1. Reseat DIMM. 2. System board. A power-on password or a supervisor password is set. Type the password and press Enter. A hard-disk password is set. Type the password and press Enter.
The hard-disk password prompt appears.
38
MT 0687
LCD-related symptoms
Important The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is: v WXGA: 8 or more bright dots, 8 or more dark dots, or a total of 9 or more bright and dark dots. Note: A bright dot means a pixel is always on (white or color.) A dark dot means a pixel is always off (black color.)
Symptom or error No beep, power-on indicator on, and a blank LCD during POST. v v v v v v v v LCD LCD LCD LCD backlight not working. too dark. brightness cannot be adjusted. contrast cannot be adjusted. FRU or action, in sequence System board. 1. Reseat the LCD connectors. 2. LCD assembly. 3. System board. 1. See important note for LCD-related symptoms. 2. Reseat all LCD connectors. 3. LCD assembly. 4. System board. LCD assembly.
LCD screen unreadable. Characters missing pixels. Screen abnormal. Wrong color displayed.
Horizontal or vertical lines displayed on LCD.
Lenovo 3000 N200
39
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects). Verify that all attached devices are supported by the computer. Verify that the power supply being used at the time of the failure is operating correctly. (See Power system checkout on page 26.) 1. Turn off the computer. 2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices: a. Non-Lenovo 3000 devices b. Devices attached to the port replicator c. Printer, mouse, and other external devices d. Battery pack e. Hard disk drive f. External diskette drive or optical drive g. DIMM h. Optical disk or diskette in the internal drive i. PC Cards 4. Turn on the computer. 5. Determine whether the problem has been solved. 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a. System board b. LCD assembly
40
MT 0687
FRU replacement notices

This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo 3000 computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once. Do the following when you service this machine: v Keep the screw kit (for the P/N, see Miscellaneous parts on page 95) in your tool bag. v Always use new screws. v Use a torque screwdriver if you have one. Tighten screws as follows: v Plastic to plastic Turn an additional 90 degrees after the screw head touches the surface of the plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic Turn an additional 180 degrees after the screw head touches the surface of the logic card:
180 degrees more
(Cross-section)
v Torque driver If you have a torque driver, refer to the Torque column for each step. v Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all of the screws are tightened firmly. v Ensure torque screwdrivers are calibrated correctly following country specifications.
Retaining serial numbers

This section includes the following descriptions: v Restoring the serial number of the system unit on page 42
Lenovo 3000 N200
41

v Retaining the UUID v Reading or writing the ECA information
Restoring the serial number of the system unit

When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer. If you replace the system board, you must restore the serial number of the system unit to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 2. Read S/N data from EEPROM. The serial number of each device in your computer is displayed; the serial number of the system unit is listed as follows: v 20: Serial number Write down that number. Note: The serial number of the system unit is also written on the label attached to the bottom of the computer. After you have replaced the system board, restore the serial number by doing the following: 1. Install the CE Utility Diskette for Lenovo 3000 notebooks and restart the computer. 2. From the main menu, select 1. Set System Identification. 3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen.
Retaining the UUID

The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board. The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information

Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application.
42
MT 0687

To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the CE Utility Diskette for Lenovo 3000 notebooks. 1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the instruction. 4. To read box build date, select 5. Read box build date from EEPROM, and follow the instruction on the screen. After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's application. Use the CE Utility Diskette for Lenovo 3000 notebooks to update the EEPROM. Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed be the same as the machine type of the machine that had the ECA applied to it. 1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 3. To write ECA information, select 1. Write ECA/rework number from EEPROM, and follow the instruction. 4. To write box build date, select 4. Write box build date from EEPROM, and follow the instruction on the screen. If the system board is being replaced, try to read the ECA information from the old system board and transfer the information to the new system. If the system board is inoperable, this will not be possible.
Lenovo 3000 N200
43
Removing and replacing a FRU

This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review FRU replacement notices on page 41. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps for removing the FRU, as given in the drawings by the numbers in square callouts. 5. When turning a screw to replace a FRU, turn it in the direction as given by the arrow in the drawing. 6. When removing the FRU, move it in the direction as given by the arrow in the drawing. 7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to replacement. For information about connecting and arranging internal cables, see Locations on page 79. 8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits. Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge (ESD) strap (P/N 6405959).
44
MT 0687
1010 Battery pack

DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
Unlock the battery release lever 1 and holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 .
2 1
Lenovo 3000 N200
45
1020 Hard disk drive slot cover

For access, remove this FRU: v 1010 Battery pack on page 45 Note: Loosen the screws 1 , but do not remove them.
1030 Hard disk drive

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover
Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode.
When installing: Make sure that the hard disk drive connector is attached firmly.
46
MT 0687
1040 DIMM slot cover

Lenovo 3000 N200
47
1050 DIMM
For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1040 DIMM slot cover on page 47
2 1
When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
48
MT 0687
1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN
1 2
Step 1
Screw (quantity) M2 3 mm, pan-head, nylon-coated (2)
Color Black
Torque 0.245 Nm (2.5 kgfcm)
In step 2 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. When installing: Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX.
Lenovo 3000 N200
49
1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN
1 2
Step 1
Color Black
In step 2 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. When installing: Plug the gray cable (MAIN) into the jack labeled 1 , the black cable (AUX) into the jack labeled 2, and the white cable (MIMO) into the jack labeled 3 on the card.
50
MT 0687
1080 Optical drive

Step 1
Screw (quantity) M2.5 6 mm, pan-head, nylon-coated (1)
Color
Torque
Dark silver 0.392 Nm (4 kgfcm)
Lenovo 3000 N200
51
1090 Heat sink assembly slot cover

52
MT 0687
1100 Heat sink assembly

For access, remove this FRU: v 1010 Battery pack on page 45 v 1090 Heat sink assembly slot cover on page 52 Note: Loosen the screws 1 , but do not remove them.
2 2
Step 2
Color Black
(continued)
Lenovo 3000 N200
53
3 4
When installing: Make sure that the fan connector is attached firmly.
When installing: Before you attach a new heat sink assembly to the computer, peel off the covering film of thermal grease. Then attach the heat sink assembly to the computer.
54
MT 0687
1110 CPU
For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1090 Heat sink assembly slot cover on page 52 v 1100 Heat sink assembly on page 53 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU in the direction shown by arrow 2 .
a b
When installing: Place the CPU on the CPU socket a , and then rotate the head of the screw in the direction shown by arrow b to secure the CPU.
Lenovo 3000 N200
55
1120 Middle cover and function board

For access, remove this FRU: v 1010 Battery pack on page 45 Note: The function board is attached to the middle cover.
1 1
Step 1
Screw (quantity) M2.5 3 mm, wafer-head, nylon-coated (2)
Color Silver
Torque 0.392 Nm (4 kgfcm)
(continued)
56
MT 0687

Lift the cover a little in the direction shown by arrow 4 . Then unlock the connector 5 and detach the connector 6 .
6 5
4 4
When installing: Make sure that the connector is attached firmly. To remove the function board, do as follows:
1
2 1
Step 2
Color Black
Lenovo 3000 N200
57
1130 Keyboard
For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1120 Middle cover and function board on page 56
Step 1
Screw (quantity) M2 x 3 mm, pan-head, nylon-coated (1)
Color Black
(continued)
58
MT 0687

Lift the keyboard a little in the direction shown by arrow 2 . Then unlock the connector 3 and detach the connector.
When installing: 1. Make sure that the keyboard connector is attached firmly. Then lock the connector. 2. Make sure that the front side of the keyboard is under the frame.
Lenovo 3000 N200
59
1140 Keyboard bezel and fingerprint reader card

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1040 DIMM slot cover on page 47 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 Note: The fingerprint reader card is attached underside of the keyboard bezel.
1
2 1 1
1 1 1
Step 1 2
Screw (quantity) M2.5 6 mm, pan-head, nylon-coated (11) M2.5 13 mm, pan-head, nylon-coated (1)
Color
Torque
Dark silver 0.392 Nm (4 kgfcm) Dark silver 0.392 Nm (4 kgfcm)
(continued)
60
MT 0687

Pull out the wireless LAN antenna cables from the guide hole of the system board 3 , and release them from the cable guides of the frame 4 .
4 4 4
When installing: Route the antenna cables along the cable guides. When you route the cables, do not tense them. To do so, the cables may get damaged by the cable guides of the frame, and may cause a broken wire.
Lenovo 3000 N200
61
6 5
Step 7
Color
Torque
When installing: Make sure that the connectors are attached firmly.
(continued)
62
MT 0687

To remove the fingerprint reader card, do as follows:
2 1 1
Slide the metal bracket of the fingerprint reader card in the direction shown by the arrow 3 , and then remove the fingerprint reader card 4 .
When installing: Make sure that the connector is attached firmly.
Lenovo 3000 N200
63
1150 Backup battery

DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 v 1140 Keyboard bezel and fingerprint reader card on page 60
When installing: Make sure that the battery connector is attached firmly.
64
MT 0687
1160 Modem daughter card (MDC)

1 1
3 2
Step 1
Color Black
Lenovo 3000 N200
65
1170 Bluetooth daughter card (BDC)

Step 1
Color Black
66
MT 0687
1180 LCD unit

1
1 1 1
Step 1
Color
Torque
When installing: Make sure that the connector is attached firmly. (continued)
Lenovo 3000 N200
67
3 4
Step 3
Color
Torque
68
MT 0687
1190 System board, 5-1 Digital Media Reader board, ExpressCard slot, and base cover
For access, remove these FRUs, in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 v 1140 Keyboard bezel and fingerprint reader card on page 60 v 1150 Backup battery on page 64 v 1160 Modem daughter card (MDC) on page 65 v 1170 Bluetooth daughter card (BDC) on page 66 v 1180 LCD unit on page 67 Note: The 5-1 Digital Media Reader board and the ExpressCard slot are attached to the system board.
1 1 3 1
Step 1
Color
Torque
Lenovo 3000 N200
69

To remove the 5-1 Digital Media Reader board, do as follows:
1 1
Step 1
Color Black
70
MT 0687

To remove the ExpressCard slot, do as follows:
1 1
Step 1
Color Black
Turn over the system board, and disconnect the ExpressCard slot assembly.
When installing: Make sure that the connector is attached firmly, and then fasten the screws.
Lenovo 3000 N200
71
2010 LCD front bezel

For access, remove this FRU: v 1010 Battery pack on page 45
1 1 1
Step 1
Screw cap
Color Silver
In step 2 , while sliding the LCD latch lever in the direction shown by the arrow, remove the bezel in the direction shown by arrow 3 .
3 3
72
MT 0687
2020 Inverter card

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 2010 LCD front bezel on page 72
1 4
2 3
Step 1
Color Silver
When installing: Make sure that connectors 3 and 4 are attached firmly.
Lenovo 3000 N200
73
2030 LCD panel, LCD cable, and hinges

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 v 1140 Keyboard bezel and fingerprint reader card on page 60 v 1180 LCD unit on page 67 v 2010 LCD front bezel on page 72 v 2020 Inverter card on page 73
1
Step 1 2
Screw (quantity) M2.5 4 mm, pan-head, nylon-coated (2) M2.5 5 mm, pan-head, nylon-coated (2)
Color Silver Silver
Torque 0.392 Nm (4 kgfcm) 0.392 Nm (4 kgfcm)
(continued)
74
MT 0687

Remove the hinges ( a ) from the LCD panel.
a 5 4 4
4 4
Step 4
Screw (quantity) M2 2.5 mm, pan-head, nylon-coated (8)
Color Silver
Remove the LCD cable assembly ( b ) from the LCD panel.
7 b
Lenovo 3000 N200
75
2040 Camera and LCD rear cover assembly

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 v 1140 Keyboard bezel and fingerprint reader card on page 60 v 1180 LCD unit on page 67 v 2010 LCD front bezel on page 72 v 2020 Inverter card on page 73 v 2030 LCD panel, LCD cable, and hinges on page 74
2 1
Step 1
Color Silver
76
MT 0687
2050 Wireless LAN antenna cables

For access, remove these FRUs in order: v 1010 Battery pack on page 45 v 1020 Hard disk drive slot cover on page 46 v 1060 PCI Express Mini Card for 802.11 a/b/g wireless LAN on page 49 v 1070 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN on page 50 v 1120 Middle cover and function board on page 56 v 1130 Keyboard on page 58 v 1140 Keyboard bezel and fingerprint reader card on page 60 v 1180 LCD unit on page 67 v 2010 LCD front bezel on page 72 v 2020 Inverter card on page 73 v 2030 LCD panel, LCD cable, and hinges on page 74 For the antennas with two cables
1
Step 1
Color Silver
Cable routing: Route the cables as shown in the following figure.
(continued)
Lenovo 3000 N200
77

For the antennas with three cables
1
1 2 2
Step 1
Color Silver
Cable routing: Route the cables as shown in the following figure.
78
MT 0687
Locations
Locations Front view

1 2 3 4 5 6 7 8 Lenovo Care button Volume control buttons Keyboard Fingerprint reader (for some models) Built-in stereo speaker (right) Touch pad Touch pad buttons System and power status indicators Note: For the description of each indicator, see Status indicators on page 32. Built-in stereo speaker (left) 5-1 Digital Media Reader RJ-11 (modem) connector Optical drive Security keyhole System and power status indicators Note: For the description of each indicator, see Status indicators on page 32. Power switch Integrated camera (for some models)
1 2 16 3 4 15 5
9 10 11 12 13 14
15 16
14
13 12 11 10 9 8
6 7
Lenovo 3000 N200
79
Locations
Rear view
1 2 3 4 5 6 7 8 9 10 USB connectors S-Video connector External monitor connector AC power connector RJ-45 (Ethernet) connector USB connectors IEEE1394 connector Microphone jack Stereo headphone jack ExpressCard slot
10
1 8 7 2 6 3 5 4
Bottom view
1 2 3 4 5 6 7 8 Heat sink assembly slot Battery pack latch Battery pack Battery pack latch Memory card slot Wireless radio switch Hard disk drive slot LCD cover latch
4 3 2 1 5
6 7 8
80
MT 0687
Parts list
Parts list
v Each FRU is available for all types or models, unless specific types or models are specified. v FRU with specific models listed and described as xxU (where U is an example of a country designator) should be used for all models ending in U. v FRU with specific models listed and described as 3Dx (where 3D is an example of a unique configuration) should be used for all of these models, unless specific country or region designator is specified. v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An N in the CRU ID column means the part is not a CRU. A single asterisk (*) means the part is an External CRU; two asterisks (**) means the part is an Internal CRU. Lenovo 3000 computers contain the following types of the external CRUs: External CRUs (pluggable) These CRUs unplug from the computer. Examples of these types of CRUs include an ac adapter, an external keyboard, a mouse, a power cord, a port replicator, a USB device, and an external bay device adapter. External CRUs with latches These CRUs have a latch to help you to remove and replace the part. Examples of these types of CRUs include a battery pack, a cover such as a memory card slot cover and a hard disk drive slot cover. Lenovo 3000 computers contain the following types of the internal CRUs: Internal CRUs (located behind an access panel) These CRUs are isolated parts within the computer that are concealed by an access panel that is typically secured by either one or two screws. Once the access panel is removed, only the specific CRU is visible. Examples of these types of CRUs include a memory card and a hard disk drive. Internal CRUs (located within the product itself) These CRUs are accessible only by opening the outer case of the computer. Examples of these CRUs include the parts beneath a cover and they are secured by either one or two screws. v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column means the part is not a RoHS compliant FRU. v FRUs marked with OP are available as options.
Lenovo 3000 N200
81
Parts list
Overall
2 3 4
5 6 7 8
b
23 22 9 10
a
21 20 11 12
19
13 14
18 17 16
15
82
MT 0687
Parts list
No. FRU FRU no. RoHS ID CRU ID
a - b See Miscellaneous parts on page 95. 1 2 3 4 5 LCD unit (see LCD FRUs on page 87.) Middle cover Function board Keyboard (see Keyboard on page 89.) Keyboard bezel assembly without fingerprint reader v 0687-29x, 2Ax, 46x, 47x, 49x, 4Gx, 4Hx, 4Zx 41R7527 R R N N 41R7530 41R7531 R R N N
Keyboard bezel assembly with fingerprint reader 41R7528 v 0687-27x, 28x, 2Bx, 32x, 48x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x 6 Fingerprint reader card 41R7610 v 0687-27x, 28x, 2Bx, 32x, 48x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x Backup battery ExpressCard slot System board assembly, 14W integrated v 0687-27x, 28x, 29x, 2Ax, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Gx, 4Hx, 4Jx, 4Kx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 52x, 53x, 69x, 6Ax, 6Bx, 6Cx, 6Dx System board assembly, 14W discrete 128 v 0687-2Bx, 4Ex, 4Lx, 4Sx, 6Ex System board assembly, 14W discrete 256 v 0687-32x, 4Mx, 4Nx, 4Vx, 4Wx, 4Xx, 4Yx, 67x, 68x, 72x, 73x 41R7611 41W6378 41R7514
7 8 9
R R R
N N N
41R7515 41R7516
R R
N N
(continued)
Lenovo 3000 N200
83
Parts list
No. 10 FRU FRU no. RoHS ID R R CRU ID N N
CPU assembly, Intel Celeron M processor 540 (1.86 GHz) 41R7621 v 0687-29x, 46x, 47x, 4Gx, 4Hx, 4Qx, 4Ux CPU assembly, Intel Core 2 Duo processor T7100 (1.83 GHz) v 0687-27x, 28x, 2Ax, 2Bx, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Jx, 4Kx, 4Px, 4Rx, 4Sx, 4Tx, 4Zx, 6Ax, 6Bx, 6Cx, 6Dx CPU assembly, Intel Core 2 Duo processor T7300 (2.0 GHz) v 0687-32x, 4Ex, 4Lx, 52x, 53x, 69x, 6Ex 42W7654
42W7655
CPU assembly, Intel Core 2 Duo processor T7500 (2.2 42W7656 GHz) v 0687-4Mx, 4Nx, 4Vx, 4Wx, 4Xx, 4Yx, 67x, 68x, 72x, 73x 11 Heat sink assembly, integrated v 0687-27x, 28x, 29x, 2Ax, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Gx, 4Hx, 4Jx, 4Kx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 52x, 53x, 69x, 6Ax, 6Bx, 6Cx, 6Dx Heat sink assembly, discrete v 0687-2Bx, 32x, 4Ex, 4Lx, 4Mx, 4Nx, 4Sx, 4Vx, 4Wx, 4Xx, 4Yx, 67x, 68x, 6Ex, 72x, 73x 12 13 Base cover assembly SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm v 0687-46x Hitachi Fujitsu Seagate 41R7703 41R7704 42T1851 41R7532
41R7533
41R7529
R R R
** ** **
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm v 0687-27x, 29x, 2Ax, 47x, 49x, 4Ax, 4Bx, 4Gx, 4Hx, 4Px, 4Qx, 4Ux, 4Zx, 6Ax, 6Bx Hitachi Fujitsu Seagate 41R7706 41R7707 42T1852 R R R ** ** **
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm v 0687-2Bx, 32x, 48x, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Rx, 4Tx, 52x, 53x, 69x, 6Cx, 6Dx, 6Ex Hitachi Fujitsu Seagate 41R7709 41R7710 42T1853 R R R ** ** **
SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm v 0687-28x, 4Mx, 4Nx, 4Sx, 4Vx, 4Wx, 4Xx, 4Yx, 67x, 68x, 72x, 73x Hitachi Seagate 41R7712 42T1854 R R ** **
(continued)
84
MT 0687
Parts list
No. 14 15 16 17 FRU Heat sink assembly slot cover Hard disk drive slot cover DIMM slot cover FRU no. 41R7614 41R7613 41R7612 RoHS ID R R R CRU ID * * *
Intel PRO Wireless 3945ABG Mini-PCI Express Adapter v 0687-27x, 28x, 2Bx, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Px, 4Qx, 4Rx, 4Tx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 53x xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU, xxV, xxY xxK xxG, xxT, xxR (802.11b/g) Broadcom 802.11bg WLAN PCI-E Mini Card v 0687-29x, 2Ax, 46x, 47x, 4Gx, 4Hx, 4Ux xxF, xxU, xxV xxE, xxJ, xxT xxA, xxB, xxG, xxH, xxK, xxL, xxM, xxP, xxQ, xxR, xxS, xxY 42T0819 42T0821 42T0823 R R R ** ** ** 42T0853 42T0857 42T0861 R R R ** ** **
Lenovo 11a/b/g/n Wireless LAN Mini-PCI Express Adapter v 0687-48x, 49x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU xxT, xxR (802.11b/g/n) Intel Wireless WiFi Link 4965AGN v 0687-32x, 4Mx, 4Nx, 4Sx, 52x xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxS, xxU, xxV, xxQ, xxY xxG 42T0865 42T0867 R R ** ** 42T0843 42T0851 R R ** **
(continued)
Lenovo 3000 N200
85
Parts list
No. 18 FRU FRU no. RoHS ID R CRU ID **
512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card 40Y8402 OP v 0687-27x, 28x, 29x, 2Ax, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Gx, 4Hx, 4Jx, 4Kx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 6Ax, 6Bx, 6Cx, 6Dx 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card OP v 0687-2Bx, 32x, 4Ex, 4Lx, 4Zx, 52x, 53x, 69x, 6Ex 40Y8403
**
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card 40Y8404 OP v 0687-4Mx, 4Nx, 4Vx, 4Wx, 4Xx, 4Yx, 67x, 68x, 72x, 73x 19 DVD/CD-RW combo drive assembly, 12.7 mm v 0687-46x, 4Gx HLDS Panasonic 42T2033 42T2041
**
R R
** **
DVD-RAM/RW drive assembly, 12.7 mm v 0687-27x, 28x, 29x, 2Ax, 2Bx, 32x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x HLDS Panasonic 20 Battery pack, Li-ion (6 cell) v 0687-all Sanyo LG 21 22 23 5-1 Digital Media Reader board Modem daughter card (MDC) Bluetooth daughter card (BDC) v 0687-27x, 28x, 32x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x Blank bezel for ExpressCard slot and 5-1 Digital Media Reader Label kit 42T4515 42T5237 41R7609 41R5798 41W1163 R R R R R * * N N N 42T2035 42T2031 R R ** **
42W2200 41R7618
R R
* N
86
MT 0687
Parts list
LCD FRUs
1
4 7 5
14.1-in. WXGA TFT

No. 1 FRU LCD front bezel FRU no. 41R7520 RoHS ID R CRU ID N
(continued)
Lenovo 3000 N200
87
Parts list
No. 2 FRU LCD panel, 14.1-in. WXGA anti-glare v 0687-2Ax, 48x CMO LPL Samsung 42T0377 42T0381 13N7154 R R R N N N FRU no. RoHS ID CRU ID
LCD panel, 14.1-in. WXGA glare v 0687-27x, 28x, 29x, 2Bx, 32x, 46x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x CMO LPL Samsung 3 Inverter card, 14W YEC Darfon 4 LCD cable assembly without a camera v 0687-27x, 29x, 2Ax, 46x, 47x, 49x, 4Gx, 4Hx LCD cable assembly with a camera v 0687-28x, 2Bx, 32x, 48x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x 5 Antenna assembly for three antennas v 0687-32x, 48x, 49x, 4Mx, 4Nx, 4Sx, 52x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x 41R7517 41R7518 41R7522 41R7523 R R R R N N N N 42T0378 42T0383 13N7160 R R R N N N
41R7525
Antenna assembly for two antennas 41R7526 v 0687-27x, 28x, 29x, 2Ax, 2Bx, 46x, 47x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 53x 6 7 LCD rear cover Camera v 0687-28x, 2Bx, 32x, 48x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 72x, 73x Hinges 41R7519 41R7524
R R
N N
41R7521
88
MT 0687
Parts list
Keyboard
Language Arabic Belgian Chinese, Traditional Czech Danish Dutch English, U.K. English, U.S. English, U.S. (International, with a Euro symbol) Finnish, Swedish French, Canadian (058) French, Canadian, Acnor French, European German Greek Hebrew Hungarian Iceland Italian Japanese Korean Norwegian Polish Portuguese Portuguese, Brazilian Russian Slovak Slovenian Spanish, European Spanish, Latin American Swiss Thai Turkish P/N (NMB) 42T3353 42T3350 42T3364 42T3358 42T3347 42T3344 42T3342 42T3338 42T3368 42T3345 42T3340 42T3339 42T3343 42T3341 42T3360 42T3355 42T3359 42T3370 42T3348 42T3363 42T3365 42T3346 42T3356 42T3352 42T3369 42T3354 42T3362 42T3361 42T3349 42T3366 42T3351 42T3367 42T3357 P/N RoHS (Chicony) ID 42T3418 42T3415 42T3429 42T3423 42T3412 42T3409 42T3407 42T3403 42T3433 42T3410 42T3405 42T3404 42T3408 42T3406 42T3425 42T3420 42T3424 42T3413 42T3428 42T3430 42T3411 42T3421 42T3417 42T3434 42T3419 42T3427 42T3426 42T3414 42T3431 42T3416 42T3432 42T3422 R CRU ID N
Lenovo 3000 N200
89
Parts list
Recovery discs
Windows XP Professional CDs
WindowsXPProfessionalispreinstalledastheoperatingsysteminthefollowing models: 06872Cx
Language Arabic Chinese, Simplified Chinese, Traditional Chinese, Traditional (Hong Kong S.A.R.) Czech Danish Dutch English, U.K. with disabled modem and WLAN English, U.S.with enabled modem and WLAN Finnish French German Greek Hebrew, English enabled Hungarian Italian Japanese Korean Norwegian Polish Portuguese, Brazilian Russian Russian, English enabled Slovenian Spanish Swedish Turkish P/N 44Y1581 N/A 44Y1575 44Y1576 44Y1580 44Y1570 44Y1573 44Y1563 44Y1562 44Y1571 44Y1564 44Y1565 44Y1585 44Y1578 44Y1584 44Y1567 44Y1577 44Y1586 44Y1572 44Y1579 44Y1568 44Y1582 44Y1588 44Y1587 44Y1566 44Y1569 44Y1583 RoHS ID R CRU ID *
MT 0687
Parts list
Recovery discs
Windows Vista Home Premium (32 bit) DVDs
Windows Vista Home Premium is preinstalled as the operating system in the following models: v 0687-27x, 2Bx, 47x, 48x, 4Ex, 4Lx, 4Rx, 4Sx, 4Zx, 6Ex
Language Bulgarian Chinese, Simplified Chinese, Traditional Chinese, Traditional (Hong Kong S.A.R.) Croatian Czech Danish Dutch English, (UD) U.K. with disabled modem and WLAN English, U.S., U.K. with enabled modem and WLAN Finnish French German Greek Hebrew Hungarian Italian Japanese Korean Norwegian Polish Portuguese Portuguese, Brazilian Romanian Russian Russian, English enabled Serbian-Latin Slovak Slovenian Spanish Swedish Turkish Ukrainian P/N 44Y0027 44Y0004 44Y0011 44Y0014 44Y0028 44Y0020 44Y0012 44Y0016 44Y0001 44Y0000 44Y0013 44Y0005 44Y0006 44Y0022 44Y0007 44Y0023 44Y0008 44Y0009 44Y0015 44Y0017 44Y0021 44Y0024 44Y0003 44Y0029 44Y0018 44Y0002 44Y0030 44Y0031 44Y0025 44Y0010 44Y0019 44Y0026 44Y0032 RoHS ID R CRU ID *
90
MT 0687
Parts list
Windows Vista Home Basic (32 bit) DVDs

Windows Vista Home Basic is preinstalled as the operating system in the following models: v 0687-29x, 2Ax, 46x, 4Ax, 4Cx, 4Gx, 4Jx, 4Px, 4Qx, 53x, 6Ax, 6Cx
Language Chinese, Simplified Chinese, Traditional Chinese, Traditional (Hong Kong S.A.R.) Czech Danish Dutch English, (UD) U.K. with disabled modem and WLAN English, U.S., U.K. with enabled modem and WLAN Finnish French German Greek Hebrew Hungarian Italian Japanese Korean Norwegian Polish Portuguese, Brazilian Russian Russian, English enabled Slovenian Spanish Swedish Turkish P/N 44Y0069 44Y0076 44Y0079 44Y0085 44Y0077 44Y0081 44Y0066 44Y0065 44Y0078 44Y0070 44Y0071 44Y0087 44Y0072 44Y0088 44Y0073 44Y0074 44Y0080 44Y0082 44Y0086 44Y0068 44Y0083 44Y0067 44Y0089 44Y0075 44Y0084 44Y0090 RoHS ID R CRU ID *
Lenovo 3000 N200
91
Parts list
Windows Vista Business (32 bit) DVDs

Windows Vista Business is preinstalled as the operating system in the following models: v 0687-28x, 32x, 49x, 4Dx, 73x, 4Hx, 4Kx, 4Nx, 4Tx, 4Ux, 4Wx, 4Yx, 52x, 68x, 69x, 6Dx
Language Bulgarian Chinese, Simplified Chinese, Traditional Chinese, Traditional (Hong Kong S.A.R.) Croatian Czech Danish Dutch English, (UD) U.K. with disabled modem and WLAN English, U.S., U.K. with enabled modem and WLAN Finnish French German Greek Hungarian Italian Japanese Korean Norwegian Polish Portuguese Portuguese, Brazilian Romanian Russian Russian, English enabled Serbian-Latin Slovak Slovenian Spanish Swedish Turkish Ukrainian P/N 44Y0059 44Y0037 44Y0043 44Y0046 44Y0060 44Y0052 44Y0044 44Y0048 44Y0034 44Y0033 44Y0045 44Y0038 44Y0039 44Y0054 44Y0055 44Y0040 44Y0041 44Y0047 44Y0049 44Y0053 44Y0056 44Y0036 44Y0061 44Y0050 44Y0035 44Y0062 44Y0063 44Y0057 44Y0042 44Y0051 44Y0058 44Y0064 RoHS ID R CRU ID *
92
MT 0687
Parts list
Windows Vista Ultimate (32 bit) DVDs

Windows Vista Ultimate is preinstalled as the operating system in the following models: v 0687-72x, 4Mx, 4Vx, 4Xx, 67x
Language Chinese, Simplified Chinese, Traditional Chinese, Traditional (Hong Kong S.A.R.) Czech Danish Dutch English, (UD) U.K. with disabled modem and WLAN English, U.S., U.K. with enabled modem and WLAN Finnish French German Greek Hungarian Italian Japanese Korean Norwegian Polish Portuguese, Brazilian Russian Russian, English enabled Spanish Slovenian Swedish Turkish P/N 44Y0095 44Y0101 44Y0104 44Y0110 44Y0102 44Y0106 44Y0092 44Y0091 44Y0103 44Y0096 44Y0097 44Y0112 44Y0113 44Y0098 44Y0099 44Y0105 44Y0107 44Y0111 44Y0094 44Y0108 44Y0093 44Y0100 44Y0114 44Y0109 44Y0115 RoHS ID R CRU ID *
Lenovo 3000 N200
93
Parts list
Corel software CDs

Language English, U.S. French Japanese Portuguese, Brazilian Spanish P/N 41X0440 41X0443 41X0608 41X0449 41X0446 RoHS ID R CRU ID *
AC adapters
FRU P/N RoHS ID CRU ID
2-pin (90 W, 20 V) adapter (models xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) OP ASTEC Lite-On 42T5000 93P5026 R R * *
2-pin (65 W, 20 V) adapter (models xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) OP Delta Lite-On ASTEC 92P1155 92P1159 92P1214 R R R * * *
3-pin (90 W, 20 V) adapter (models xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxT, xxQ, xxR, xxV) OP ASTEC Lite-On 92P1104 92P1108 R R * *
3-pin (65W, 20 V) adapter (models xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxT, xxQ, xxR, xxV) OP Delta Lite-On ASTEC 92P1153 92P1157 92P1212 R R R * * *
94
MT 0687
Parts list
Miscellaneous parts
FRU Screw kit (including nylon-coated screws): v M2 2.5 mm (silver), pan-head (10) v M2 3 mm (black), pan-head (21) v M2 4 mm (silver), pan-head (6) v M2.5 3 mm (silver), wafer-head (2) v M2.5 5 mm (silver), pan-head (6) v M2.5 6 mm (dark silver), pan-head (19) v M2.5 9 mm (dark silver), pan-head (7) v M2.5 13 mm (dark silver), pan-head (1) v M3 2.8 mm (black), pan-head (4) v Hex stud (2) System miscellaneous parts: v Bracket, fingerprint reader v Bracket, optical drive v Bracket, hard disk drive v Bracket, touch pad v Rubber foot (4) v Screw cap rubber (6) Cable miscellaneous parts v MDC cable v Fingerprint reader cable v Function board cable v Touch pad cable v Bluetooth cable P/N 41R7617 RoHS ID R CRU ID N
41R7615
41R7616
Common parts list

Tools
Tool Triconnector wrap plug Audio wrap cable USB parallel test cable Screwdriver kit Mini PC tool set 1/4" drive spinner handle 1/4" Sq. to 1/4" hex torx adapter TR7-TR-10 tamper resistant torx bits Removal tool antenna RF connector PCI-Express/USB wrap card P/N 72X8546 66G5180 05K2580 95F3598 00P7033 1650840 93F2838 00P6967 08K7159 27K9813
CE Utility Diskette for Lenovo 3000 notebooks Note: Download the file from the following Web site: http://www.lenovo.com/ spm
Lenovo 3000 N200
95
Parts list
Power cords
A Lenovo 3000 power cord for a specific country or region is usually available only in that country or region: For 2-pin power cords:
Region Argentina Brazil Canada, U.S. Japan P/N (Longwell) 42T5020 42T5026 42T5008 42T5014 P/N (Volex) RoHS ID 42T5105 42T5111 42T5093 42T5099 R CRU ID *
For 3-pin power cords:

Region Australia, New Zealand Denmark Europe Hong Kong S.A.R. of China, U.K. India Israel Italy Korea South Africa Switzerland Thailand, Taiwan P/N (Longwell) 42T5050 42T5041 42T5029 42T5035 42T5083 42T5062 42T5047 42T5077 42T5056 42T5044 42T5004 P/N (Volex) RoHS ID 42T5135 42T5126 42T5114 42T5120 42T5168 42T5147 42T5132 42T5162 42T5141 42T5129 42T5089 R CRU ID *
96
MT 0687
Notices
Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to: Lenovo (United States), Inc. 1009 Think Place - Building One Morrisville, NC 27560 U.S.A. Attention: Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk. Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been
Lenovo 3000 N200
97
Notices
estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo Lenovo Care Rescue and Recovery The following terms are trademarks of the International Business Machines Corporation in the United States, other countries, or both: IBM (used under license) The following terms are trademarks of Microsoft Corporation in the United States, other countries, or both: Microsoft Windows Windows Vista The following are trademarks of Intel Corporation or its subsidiaries in the United States, other countries, or both: Intel Intel Core 2 Duo Celeron Other company, product, or service names may be the trademarks or service marks of others.
98
MT 0687
Trademarks
Lenovo 3000 N200
99
Part Number: 42X3552
(1P) P/N: 42X3552

Lenovo 3000 N200 Hardware Maintenance Manual

Uploaded by

Copyright:

Available Formats

Lenovo 3000 N200 Hardware Maintenance Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lenovo 3000 N200 Hardware Maintenance Manual

Uploaded by

Copyright:

Available Formats

Lenovo 3000 N200 Hardware Maintenance Manual

Lenovo 3000 N200 Hardware Maintenance Manual

Lenovo 3000 N200 . . . . . . . . . . 29

Copyright Lenovo 2007

Important service information

Strategy for replacing FRUs

Copyright Lenovo 2007

Important service information

Strategy for replacing a hard disk drive

Important notice for replacing a system board

How to use error messages

Important service information

Using PC Entitlement Warehouse (PEW)

Using the HMM

Important service information

Important information about replacing RoHS compliant FRUs

Diskette compatibility matrix

Diskette compatibility matrix

Safety notices: multilingual translations

Safety inspection guide

Handling devices that are sensitive to electrostatic discharge

Laser compliance statement

Laser compliance statement

Laser compliance statement

Read this first

Read this first

Related service information

Related service information

Service Web site

Restoring the factory contents by using Product Recovery discs

Related service information

Related service information

How to remove the power-on password

How to remove the hard-disk password

Related service information

Screen blank mode

Sleep (standby) mode

Related service information

Testing the computer

Creating the PC-Doctor diagnostics diskette

PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.

Detecting system information with PC-Doctor

PC-Doctor for Windows

Power system checkout

Checking the ac adapter

Voltage (V dc) +20 0 Ground

Checking operational charging

Checking the battery pack

Voltage (V dc) + 0 to + 12.6 Ground ()

Lenovo 3000 N200

Copyright Lenovo 2007

Intel Celeron M processor 540 (1.86 GHz), 1MB L2

Intel Core 2 Duo processor T7100 (1.8GHz), 2MB L2

cache (533 MHz)

Graphic memory chip Display Standard memory

CMOS RAM Hard disk drive

Lenovo 3000 N200

Indicator 1 Caps lock

5-1 Digital Media Reader status