Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

High Voltage with Flexible Termination System (HV FT-CAP) X7R Dielectric, 500VDC-3000VDC (Commercial Grade)
Overview
KEMETs High Voltage with Flexible Termination (HV FT-CAP) surface mount MLCCs in X7R dielectric combine high voltage and flexible termination technologies. Featuring a 125C maximum operating temperature and considered temperature stable, these devices address the primary failure mode of MLCCsflex cracks, which are typically the result of excessive shear stresses produced during board flexure or thermal cycling. Utilizing a conductive silver epoxy between the base metal and nickel barrier layers of KEMETs standard termination system, flexible termination technology directs board flex stress away from the ceramic body and into the termination area, therefore mitigating flex cracks which can result in low IR or short circuit failures. Although flexible termination technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination systems. The HV FT-CAP offers low leakage current, exhibits low ESR at high frequencies and finds conventional use as snubbers or filters in applications such as switching power supplies and lighting ballasts. Their exceptional performance at high frequencies has made them a preferred choice of design engineers worldwide. In addition to their use in power supplies, these capacitors are widely used in industries related to telecommunications, medical, military, aerospace, semiconductors and test/diagnostic equipment. Combined with the stability of an X7R dielectric and designed to accommodate all capacitance requirements, these flex-robust devices are RoHS-compliant, offer up to 5mm of flex-bend capability and exhibit a predictable change in capacitance with respect to time and voltage. Capacitance change with reference to ambient temperature is limited to 15% from -55C to +125C.

Benefits

-55C to +125C operating temperature range Superior flex performance (up to 5mm) Pb-Free and RoHS compliant (excluding SnPb end metallization option) EIA 0805, 1206, 1210, 1808, 1812, 1825, 2220 and 2225 case sizes DC voltage ratings of 500V, 630V, 1KV, 1.5KV, 2KV, 2.5KV and 3KV Capacitance offerings ranging from 62pF to 0.27F Available capacitance tolerances of 5%, 10% or 20%. Low ESR and ESL Non-polar device, minimizing installation concerns

100% pure matte tin-plated end metallization allowing for excellent solderability SnPb plated end metallization option available upon request (5% min)

Ordering Information
C
Ceramic

1210

473
Capacitance Code (pF) 2 Sig. Digits + Number of Zeros

K
Capacitance Tolerance J = 5% K = 10% M = 20%

C
Voltage C = 500V B = 630V D = 1000V F = 1500V G = 2000V Z = 2500V H = 3000V

R
Dielectric R = X7R

A
Failure Rate/ Design A = N/A

C
End Metallization1 C = 100% Matte Sn L = SnPb (5% min)

TU
Packaging/Grade (C-Spec)2 Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked

Case Size Specification/ (L" x W") Series 0805 1206 1210 1808 1812 1825 2220 2225 X = Flexible Termination

1 2

Additional termination options may be available. Contact KEMET for details. Additional reeling or packaging options may be available. Contact KEMET for details.

One WORLD

One Brand

One Strategy

One Focus

One Team

One KEMET
C1025-1 10/12/2010 1

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Dimensions Millimeters (Inches)

T

L B

EIA Size Code

0805 1206 1210 1808 1812 1825 2220 2225

Metric Size Code

2012 3216 3225 4520 4532 4564 5650 5664

L Length
2.1 (.083) 0.30 (.012) 3.3 (.130) 0.40 (.016) 3.3 (.130) 0.40 (.016) 4.7 (.185) 0.50 (.020) 4.5 (.178) 0.40 (.016) 4.6 (.181) 0.40 (.016) 5.9 (.232) 0.75 (.030) 5.9 (.232) 0.75 (.030)

W Width
1.25 (.049) 0.20 (.008) 1.60 (.063) 0.20 (.008) 2.50 (.098) 0.20 (.008) 2.00 (.079) 0.20 (.008) 3.20 (.126) 0.30 (.012) 6.40 (.252) 0.40 (.016) 5.00 (.197) 0.40 (.016) 6.40 (.248) 0.40 (.016)

B Bandwidth
0.50 (0.02) 0.25 (.010) 0.60 (.024) 0.25 (.010) 0.60 (.024) 0.25 (.010) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014) 0.70 (.028) 0.35 (.014)

T Thickness

Mounting Technique
Solder Wave or Solder Reflow

See Table 2 for Thickness

Solder Reflow Only

Applications

Typical applications include switch mode power supplies (input filters, resonators, tank circuits, snubber circuits, output filters), high voltage coupling and DC blocking, lighting ballasts, voltage multiplier circuits, DC/DC converters and coupling capacitors in uk converters. Markets include power supply, LCD fluorescent backlight ballasts, HID lighting, telecom equipment, industrial and medical equipment/control, LAN/WAN interface, analog and digital modems, and automotive. X7R dielectrics are not designed for AC line filtering or pulse applications.

Qualification/Certification

Commercial grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance and Reliability.

Environmental Compliance

Devices with C end metallization option are RoHS PRC ( Peoples Republic of China) compliant. Devices with L end metallization option do no meet RoHS criteria.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Electrical Parameters/Characteristics
Item
Operating Temperature Range: Capacitance Change with Reference to +25C and 0 Vdc Applied (TCC): Aging Rate (Max % Cap Loss/Decade Hour): Dielectric Withstanding Voltage: Dissipation Factor (DF) Maximum Limit @ 25C: Insulation Resistance (IR) Limit @ 25C: Insulation Resistance (IR) Limit @ 125C: -55C to +125C 15% 3.5% 150% of rated voltage for voltage rating of < 1000V 120% of rated voltage for voltage rating of 1000V 2.5% 1000 megohm microfarads or 100G 100 megohm microfarads or 10G

Parameters/Characteristics

To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz and 1 Vrms if capacitance >1000pF

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Table 1A (0805 - 1812 Case Sizes)

Cap Cap Code Series
Voltage Code Voltage DC Cap Tolerance

C0805
C B D C B

C1206
D F G C B

C1210
D F G C B D

C1808
F G Z H C B D

C1812
F G Z H

500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000

Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions

10 pF 100 J K M 11 pF 110 J K M 12 pF 120 J K M 13 pF 130 J K M 15 pF 150 J K M 16 pF 160 J K M 18 pF 180 J K M 20 pF 200 J K M 22 pF 220 J K M 24 pF 240 J K M 27 pF 270 J K M 30 pF 300 J K M 33 pF 330 J K M 36 pF 360 J K M 39 pF 390 J K M 43 pF 430 J K M 47 pF 470 J K M 51 pF 510 J K M 56 pF 560 J K M 62 pF 620 J K M DG DG DG 68 pF 680 J K M DG DG DG 75 pF 750 J K M DG DG DG EG EG EG 82 pF 820 J K M DG DG DG EG EG EG 91 pF 910 J K M DG DG DG EG EG EG 100 pF 101 J K M DG DG DG EG EG EG 110 pF 111 J K M DG DG DG EF EF EF 120 pF 121 J K M DG DG DG EF EF EF 130 pF 131 J K M DG DG DG EF EF EF 150 pF 151 J K M DG DG DG EF EF EF 180 pF 181 J K M DG DG DG EF EF EF 220 pF 221 J K M DG DG DG EF EF EF 270 pF 271 J K M DG DG DG EF EF EF 330 pF 331 J K M DG DG DG EF EF EF 390 pF 391 J K M DG DG DG EF EF EF 470 pF 471 J K M DG DG DG EF EF EF 560 pF 561 J K M DG DG DG EF EF EF 680 pF 681 J K M DG DG DG EF EF EF 820 pF 821 J K M DG DG DG EF EF EF 1,000 pF 102 J K M DG DG DG EF EF EF 1,200 pF 122 J K M DG DG DG EF EF EF 1,500 pF 152 J K M DG DG DG EF EF EF 1,800 pF 182 J K M DG DG DG EF EF EF 2,000 pF 202 J K M DG DG DG EF EF EF 2,200 pF 222 J K M DG DG DG EF EF EF 2,700 pF 272 J K M DG DG DG EF EF EF 3,300 pF 332 J K M DG DG DG EF EF EF 3,900 pF 392 J K M DG UD UD EF EF EF 4,700 pF 472 J K M DG UD UD EF EF EF 5,600 pF 562 J K M DG XUD UD EF 473 EF EF C 1210 6,800 pF 682 J K M DG UD UD EG EG EG Case Capacitance 8,200 pF Ceramic 822 J Size K MSpecifi DG cation/ EG EG UD UD EG (L" Series Code 10,000 pF 103 J x W") K M UD EG(pF) EG UD UD EG 12,000 pF 123 J K M UD UD UD EG UD UD 0805 X = Flexible 2 Sig. Digits + 15,000 pF 153 J K M UD UD UD EG UD UD 1206 Termination Number of Zeros 18,000 pF 183 J K M UD UD UD UD UD UD 1210 22,000 pF 223 J K M UD UD UD UD 27,000 pF 273 J1808 K M UD UD UD UD Voltage DC

EG EG EG EG EF EF EF EF EF EF EF EF EF EF EF EF EF EF EG EG EG EG EG EG EG EG EG

Cap

1812 G = 2000V 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 1825 Z = 2500V Cap Voltage F G C B D F G C B D F G Z H C B D F G Z H 2220 Code C B D C B D H = 3000V Code 2225 Series C0805 C1206 C1210 C1808 C1812

LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LA LA LA LA LB LB LB FL FL FL FL FL LA LA LA LA LB LB LB FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FM LB LB LB LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH FL FL FL FL FM LA LA LA LB LC GH GH GH GH GK FL FL FL FL FM LA LA LA LB GH GH GH GH GK FL FL FL FL FK LA LA LA LB GH GH GH GH GK FL FL FL FL FK LA LA LA LB GH GH GH GH FL FM GH GH GH K FL FL C R LA LB ALB LC C TUGK FL FL FL FM LA LB LB LC GH GH GH GK Rate/LC Capacitance Packaging/Grade FL FLVoltage FL FK Dielectric LA Failure LB LB End Metallization1 GH GH GH GK2 Design Tolerance FL FL FL FK LA LB LB LC GH GH (C-Spec) GH GK FL FL FL FK LA LC LC GH GK GK GK J = 5% C = 500V R = X7R A = N/A C = 100% Matte Sn Blank = Bulk FL FL FL LA LC LC GH GK GK K = 10% B = 630V L = SnPb (5% min) TU = 7" Reel FL FL FL LA UD UD GH GK GK M = 20% D = 1000V Unmarked FL FM FM LA UD UD GH GK GK F = 1500V FM FK FK LA UD UD GH TM = 7" Reel Marked

EG EG EG EG EG EG EG EG EG EG

GK GK GK GK GK GK GK GK GK GK GK GK

GK GK GK GK GK GK GK GK GK GK GK GK

UD = Under Developement KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com C1025-1 10/12/2010 4

Roll Over for Order Info.

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Table 1A con't (0805 - 1812 Case Sizes)

Cap
33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 uF 0.12 uF 0.15 uF 0.18 uF 0.22 uF 0.27 uF 0.33 uF

Cap Code
333 393 473 563 683 823 104 124 154 184 224 274 334

Series
Voltage Code Voltage DC Cap Tolerance J J J J J J J J J J J K K K K K K K K K K K M M M M M M M M M M M

C0805
C B D C B

C1206
D F G C B

C1210
D F G C B D

C1808
F G Z H C B D

C1812
F G Z H

500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000

UD

Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions

UD UD UD UD UD UD UD UD UD UD UD UD UD

UD UD UD UD UD UD UD UD

FM FK FK

UD UD UD UD UD UD UD

UD UD UD UD UD UD UD

UD UD UD UD UD UD UD UD UD UD UD UD UD UD
LC LC LC LC

UD UD UD UD UD UD UD

GH GH GH GH GK GK GK

Cap

Cap Voltage Code C Code

Series

Voltage DC

500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 B C0805 D C B D C1206 F G C B D C1210 F G C B D F C1808 G Z H C B D F C1812 G Z H

Table 1B (1825 - 2225 Case Sizes)

Cap Cap Code Series
Voltage Code Voltage DC Cap Tolerance 100 pF 101 J K M 110 pF 111 J K M 120 pF 121 J K M 130 pF 131 J K M 150 pF 151 J K M 180 pF 181 J K M 220 pF 221 J K M 270 pF 271 J K M 330 pF 331 J K M HG 390 pF 391 J K M HG 470 pF 471 J K M HG 560 pF 561 J K M HG 680 pF 681 J K M HG 820 pF 821 J K M HG 1,000 pF 102 J K M HG 1,200 pF 122 J K M HG 1,500 pF 152 J K M HG 1,800 pF 182 J K M HE C 1210 X 2,000 pF 202 J K M HE 2,200 pF 222 Case J SizeK Specifi M cation/ HE 2,700 pF Ceramic 272 J M HE (L" x W") K Series 3,300 pF 332 J K M HE 0805 = Flexible 3,900 pF 392 J K XM HE 1206 4,700 pF 472 J K Termination M HE 5,600 pF 562 J K M HE 1210 6,800 pF 682 J K M HE 1808 C 500 B 630 D

C1825
F G Z H C 500 B 630 D 1000 1500 2000 2500 3000

C2220
F G Z H C 500 B 630 D 1000 1500 2000 2500 3000

C2225
F G Z H 1000 1500 2000 2500 3000

Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions

Cap

Cap Code

1812 Voltage DC 1825 Voltage Code 2220 2225Series

HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HE HE HE 473 HE HE HE HE Capacitance HE HE HE HE HE Code (pF) HE HE HE Digits + HE2 Sig. HE HE Number HE HE of Zeros HE HE HE HE HE HE HE 630 B D F C1825

500 C

G = 500 2000V630 1000 1500 2000 2500 3000

G Z H

HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HE HG HG JP JP JP K C R HE HG HG JE JE JE HE HG HG JE JE JE Capacitance HE HG HG Voltage JE JE Dielectric JE Tolerance HE HG HG JE JE JE J = 5% C = 500V X7R HE JE JE R = JE K = 10% B = 630V HE JE JE JE HE JE JE JE M = 20% D = 1000V HE JE JE JE F = 1500V

JP JP JP JP JP JP JP JP JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF A C TU JE JE JP JP KF KF KF KF KF JE JE JP KF KF KF KF KF Failure Rate/ JP Packaging/Grade 1 Metallization JE JE JP EndJP KE KE KE KE KE 2 Design (C-Spec) JE JE JP JP KE KE KE KE KE N/A JPC = 100% JE A = JE JP Matte KE Sn KE Blank KE = Bulk KE KE L = SnPb (5% = 7" Reel JE JP KE min) KE TU KE KE KE JE JP KE KE KE Unmarked KE KE JE JP KE KE TM KE KE Marked KF = 7" Reel 500 C 630 B F G Z H D F C2225 G

KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF

KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF

Z = 2500V C B H = 3000V

1000 1500 2000 2500 3000 D C2220

1000 1500 2000 2500 3000 Z H

UD = Under Developement. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com C1025-1 10/12/2010 5

Roll Over for Order Info.

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Table 1B con't (1825 - 2225 Case Sizes)

Cap
8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 uF 0.12 uF 0.15 uF 0.18 uF 0.22 uF 0.27 uF 0.33 uF 0.39 uF 0.47 uF 0.56 uF 0.68 uF 0.82 uF 1.0 uF 1.2 uF 1.5 uF 1.8 uF 2.2 uF 2.7 uF 3.3 uF

Cap Code
822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335

Series
Voltage Code Voltage DC Cap Tolerance J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M HE HE HE HE HE HE HE HE HE HE HE HG HG HG HG HG HG HG C 500 B 630 HE HE HE HE HE HG HG HG HG HG D

C1825
F G Z H C 500 JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JP JP JP B 630 JE JE JP JP JP JP JP JP JP JP D 1000 1500 2000 2500 3000 HE HE HE HE HE HG HG HG HG HG HE HE HG HG HG HG HG HE

C2220
F G Z H C 500 KE KE KE KE KE KE KE KE KE KE KE KE KE KE KE KF KF KF KF B 630 KE KE KE KE KE KF KF KF KF KF KF KF KF D 1000 1500 2000 2500 3000 JE JE JP JP JP JP JP JP JP JP JE JE JP JP JP JP JP JP JP

C2225
F G Z H 1000 1500 2000 2500 3000 KE KE KE KE KE KF KF KF KF KF KF KF KF KE KE KE KE KE KF KF KF KF KF KF KF KF

Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions

Cap

Cap Code

Voltage DC Voltage Code Series

500 C

630 B

1000 1500 2000 2500 3000 D F C1825 G Z H

500 C

630 B

1000 1500 2000 2500 3000 D F C2220 G Z H

500 C

630 B

1000 1500 2000 2500 3000 D F C2225 G Z H

C
Ceramic

1210

473
Capacitance Code (pF) 2 Sig. Digits + Number of Zeros

K
Capacitance Tolerance J = 5% K = 10% M = 20%

C
Voltage C = 500V B = 630V D = 1000V F = 1500V G = 2000V Z = 2500V H = 3000V

R
Dielectric R = X7R

A
Failure Rate/ Design A = N/A

C
End Metallization1 C = 100% Matte Sn L = SnPb (5% min)

TU
Packaging/Grade (C-Spec)2 Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked

Case Size Specification/ (L" x W") Series 0805 1206 1210 1808 1812 1825 2220 2225 X = Flexible Termination

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

Roll Over for Order Info.

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Table 2 Chip Thickness / Packaging Quantities

Thickness Code
AA AB BB CB CC CD DC DD DL DE DF DG DH EB EK EC EN ED EE EF EM EG EH EJ FB FC FD FE FF FG FL FO FH FP FM FJ FN FT FK FR FS PA MA NA NA LD LA LB LC GB GC GD GE GH GF GG GK GJ GN GL GM GO HB HC HD HE HF HG JB JC JD JE JF JP JG JH JO KB KC KD KE KF

Chip Size
01005 0201 0402 0603 0603 0603 0805 0805 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1220 1632 1706 1706 1808 1808 1808 1808 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 1825 1825 2220 2220 2220 2220 2220 2220 2220 2220 2220 2225 2225 2225 2225 2225

Thickness Range (mm)

0.20 0.02 0.30 0.03 0.50 0.05 0.80 0.07 0.80 0.10 0.80 0.15 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.25 0.20 0.78 0.10 0.80 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.20 0.15 1.25 0.15 1.60 0.15 1.60 0.20 1.70 0.20 0.78 0.10 0.90 0.10 0.95 0.10 1.00 0.10 1.10 0.10 1.25 0.15 1.40 0.15 1.50 0.20 1.55 0.15 1.60 0.20 1.70 0.20 1.85 0.20 1.85 0.20 1.90 0.20 2.10 0.20 2.25 0.20 2.50 0.20 0.80 0.10 0.80 0.10 0.90 0.10 0.90 0.10 0.90 0.10 1.40 0.15 1.60 0.15 2.00 0.15 1.00 0.10 1.10 0.10 1.25 0.15 1.30 0.10 1.40 0.15 1.50 0.10 1.55 0.10 1.60 0.20 1.70 0.15 1.70 0.20 1.90 0.20 2.00 0.20 2.50 0.20 1.10 0.15 1.15 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.60 0.20 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 1.50 0.15 1.60 0.20 1.70 0.15 1.80 0.15 2.40 0.15 1.00 0.15 1.10 0.15 1.30 0.15 1.40 0.15 1.60 0.20

Qty per Reel 7" Plastic

Qty per Reel 13" Plastic

Qty per Reel 7" Paper

15000 15000 10000 4000 4000 4000 4000 4000

Qty per Reel 13" Paper

50000 10000 10000 10000 10000 10000

Qty per Bulk Cassette

50000 15000

4000 2500 2500 2500 2500 4000 2000 4000 4000 2500 2500 2500 2500 2000 2000 2000 4000 4000 4000 2500 2500 2500 2000 2000 2000 2000 2000 2000 2000 1500 2000 2000 1000 4000 4000 4000 4000 2500 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 1000 1000 1000 1000 1000

10000 10000 10000 10000 10000 10000 8000 10000 10000 10000 10000 10000 10000 8000 8000 8000 10000 10000 10000 10000 10000 10000 8000 8000 8000 8000 8000 8000 8000 4000 8000 8000 4000 10000 10000 10000 10000 10000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 4000 4000 4000 4000 4000

4000

10000

Package Quantity Based on Finished Chip Thickness Specifications

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Soldering Process

Recommended Soldering Technique: Solder wave or solder reflow for EIA case sizes 0603, 0805 and 1206 All other EIA case sizes are limited to solder reflow only Recommended Soldering Profile: KEMET recommends following the guidelines outlined in IPC/JEDEC J-STD-020

Table 3 Chip Capacitor Land Pattern Design Recommendations per IPC-7351

EIA Size Code
0603 0805 1206 1210 1808 1812 1825 2220 2225

Metric Size Code

1608 2012 3216 3225 4520 4532 4564 5650 5664

Density Level A: Maximum (Most) Land Protrusion (mm)

C 0.85 1.05 1.60 1.60 2.25 2.10 2.15 2.85 2.85 Y 1.25 1.45 1.65 1.65 1.85 1.80 1.80 2.10 2.10 X 1.10 1.55 1.90 2.80 2.30 3.60 6.90 5.50 6.90 V1 4.00 4.60 5.90 5.90 7.40 7.00 7.10 8.80 8.80 V2 2.10 2.60 2.90 3.80 3.30 4.60 7.90 6.50 7.90 C 0.75 0.95 1.50 1.50 2.15 2.00 2.05 2.75 2.75

Density Level B: Median (Nominal) Land Protrusion (mm)

Y 1.05 1.25 1.45 1.45 1.65 1.60 1.60 1.90 1.90 X 1.00 1.45 1.80 2.70 2.20 3.50 6.80 5.40 6.80 V1 3.10 3.70 5.00 5.00 6.50 6.10 6.20 7.90 7.90 V2 1.50 2.00 2.30 3.20 2.70 4.00 7.30 5.90 7.30 C 0.65 0.85 1.40 1.40 2.05 1.90 1.95 2.65 2.65

Density Level C: Minimum (Least) Land Protrusion (mm)

Y 0.85 1.05 1.25 1.25 1.45 1.40 1.40 1.70 1.70 X 0.90 1.35 1.70 2.60 2.10 3.40 6.70 5.30 6.70 V1 2.40 3.00 4.30 4.30 5.80 5.40 5.50 7.20 7.20 V2 1.20 1.70 2.00 2.90 2.40 3.70 7.00 5.60 7.00

Density Level A: For low-density Product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC-7351).

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Table 4 Performance & Reliability: Test Methods and Conditions

Stress
Ripple Current Terminal Strength Board Flex

Reference
"Heat Generation T : 20C max." JIS-C-6429 JIS-C-6429

Test or Inspection Method

"Reflow solder the capacitor onto a PC board and apply voltage with 10kHz~1Mhz sine curve. (Ripple voltage must be < rated voltage)" Appendix 1, Note: Force of 1.8kg for 60 seconds. Appendix 2, Note: 2mm (min) for all except 3mm for C0G. Magnification 50X. Conditions:

Solderability

J-STD-002

a) Method B, 4 hrs @ 155C, dry heat @ 235C b) Method B @ 215C category 3 c) Method D, category 3 @ 260C

Temperature Cycling Biased Humidity Moisture Resistance Thermal Shock High Temperature Life Storage Life Mechanical Shock Resistance to Solvents

JESD22 Method JA-104 MIL-STD-202 Method 103 MIL-STD-202 Method 106 MIL-STD-202 Method 107 MIL-STD-202 Method 108 MIL-STD-202 Method 108 MIL-STD-202 Method 213 MIL-STD-202 Method 215

1000 Cycles (-55C to +125C), Measurement at 24 hrs. +/- 2 hrs after test conclusion. Load Humidity: 1000 hours 85C/85%RH and 300VDC Max. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. Low Volt Humidity: 1000 hours 85C/85%RH and 1.5V. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. t = 24 hours/cycle. Steps 7a & 7b not required. Unpowered. Measurement at 24 hrs. +/- 2 hrs after test conclusion. -55C/+125C. Note: Number of cycles required-300, Maximum transfer time-20 seconds, Dwell time-15 minutes. Air-Air. 1000 hours at 125C (85C for X5R, Z5U and Y5V) with rated voltage applied. 150C, 0VDC, for 1000 Hours. Figure 1 of Method 213, Condition F. Add Aqueous wash chemical - OKEM Clean or equivalent.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Tape & Reel Packaging Information

KEMET offers Multilayer Ceramic Chip Capacitors packaged in 8mm, 12mm and 16mm tape on 7" and 13" reels in accordance with EIA standard 481. This packaging system is compatible with all tape fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips.

Bar Code Label

Anti-Static Reel

KE

ME

Embossed Plastic* or Punched Paper Carrier.

Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 & 2225 Military)

Sprocket Holes
Embossment or Punched Cavity 8mm, 12mm or 16mm Carrier Tape

178mm (7.00") or 330mm (13.00")

Anti-Static Cover Tape (.10mm (.004") Max Thickness)

*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.

Table 5 Carrier Tape Configuration (mm)

EIA Case Size
01005 - 0402 0603 - 1210 1805 - 1808 1812 KPS 1210 KPS 1812 & 2220 Array 0508 & 0612

Tape size (W)*

8 8 12 12 12 16 8

Pitch (P1)*
2 4 4 8 8 12 4

*Refer to Figure 1 for W and P1 carrier tape reference locations. *Refer to Table 6 for tolerance specifications. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com C1025-1 10/12/2010 10

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Figure 1 Embossed (Plastic) Carrier Tape Dimensions

T T2 P2 Do Po
[10 pitches cumulative tolerance on tape 0.2 mm]

E1

Ao F Ko B1 Bo E2 W

S1 T1
Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Center Lines of Cavity

P1 D 1
Embossment For cavity size, see Note 1 Table 5

User Direction of Unreeling

Table 6 Embossed (Plastic) Carrier Tape Dimensions

Metric will govern Constant Dimensions Millimeters (Inches)
Tape Size 8mm 12mm 16mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) D0 D1 Min. Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 R Ref. Note 2 25.0 (0.984) 30 (1.181) S1 Min. Note 3 0.600 (0.024) T Max. T1 Max.

1.75 0.10 (0.069 0.004)

4.0 0.10 (0.157 0.004)

2.0 0.05 (0.079 0.002)

0.600 (0.024)

0.100 (0.004)

Variable Dimensions Millimeters (Inches)

Tape Size 8mm 12mm 16mm Pitch Single (4mm) Single (4mm) & Double (8mm) Triple (12mm) B1 Max. Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Min. 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F 3.5 0.05 (0.138 0.002) 5.5 0.05 (0.217 0.002) 5.5 0.05 (0.217 0.002) P1 4.0 0.10 (0.157 0.004) 8.0 0.10 (0.315 0.004) 8.0 0.10 (0.315 0.004) T2 Max 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Max 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0

Note 5

1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12mm tapes and 10 maximum for 16mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4). (e) for KPS Series product A0 and B0 are measured on a plane 0.3mm above the bottom of the pocket. (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

11

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Figure 2 Punched (Paper) Carrier Tape Dimensions

T Do P2 Po
[10 pitches cumulative tolerance on tape 0.2 mm]

E1

A0

F E2 W

Bottom Cover Tape

B0

T1

P1
Top Cover Tape

T1

Center Lines of Cavity

Cavity Size, See Note 1, Table 7 Bottom Cover Tape

User Direction of Unreeling

Table 7 Punched (Paper) Carrier Tape Dimensions

Metric will govern Constant Dimensions Millimeters (Inches)
Tape Size 8mm D0 1.5 +0.10-0.0 (0.059 +0.004, -0.0) E1 1.75 0.10 (0.069 0.004) P0 4.0 0.10 (0.157 0.004) P2 2.0 0.05 (0.079 0.002) T1Max 0.10 (.004) Max. G Min 0.75 (.030) R Ref. Note 2 25 (.984)

Variable Dimensions Millimeters (Inches)

Tape Size 8mm 8mm Pitch Half (2mm) Single (4mm) E2 Min 6.25 (0.246) F 3.5 0.05 (0.138 0.002) 2.0 0.05 (0.079 0.002) 4.0 0.10 (0.157 0.004) P1 T Max 1.1 (0.098) W Max 8.3 (0.327) 8.3 (0.327) A0 B 0 Note 5

1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 5).

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

12

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Packaging Information Performance Notes

Tape Width
8mm 12mm & 16mm

1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:

Peel Strength
0.1 Newton to 1.0 Newton (10gf to 100gf) 0.1 Newton to 1.3 Newton (10gf to 130gf)

The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 30010 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556 and EIA-624.

Figure 3 Maximum Component Rotation

T

Maximum Component Rotation Top View

Typical Pocket Centerline

Maximum Component Rotation Side View

s

Bo

Tape Width (mm) 8,12 16-200

Maximum Rotation ( 20 10

T)

Typical Component Centerline

Ao

Tape Width (mm) 8,12 16-56 72-200

Maximum Rotation ( 20 10 5

S)

Figure 4 Maximum Lateral Movement

8mm & 12mm Tape
0.5 mm maximum 0.5 mm maximum

16mm Tape
1.0 mm maximum 1.0 mm maximum

Figure 5 Bending Radius

Embossed Carrier Punched Carrier

Bending Radius

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

13

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Figure 6 Reel Dimensions

Full Radius, See Note Access Hole at Slot Location ( 40 mm min.)

W3 (Includes

flange distortion at outer edge)

W2 (Measured at hub) A D
(See Note)

C
(Arbor hole diameter) If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 mm min. depth

N W1 (Measured at hub)

(see Note)

Note: Drive spokes optional; if used, dimensions B and D shall apply.

Table 8 Reel Dimensions

Metric will govern Constant Dimensions Millimeters (Inches)
Tape Size 8mm 12mm 16mm A 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) B Min 1.5 (0.059) C 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) D Min 20.2 (0.795)

Variable Dimensions Millimeters (Inches)

Tape Size 8mm 12mm 16mm 50 (1.969) N Min 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) W1 W2 Max 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) W3 Shall accommodate tape width without interference

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

14

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Figure 7 Tape Leader & Trailer Dimensions

Embossed Carrier Punched Carrier 8 mm & 12 mm only Carrier Tape Round Sprocket Holes

END

START
Top Cover Tape

Elongated Sprocket Holes (32 mm tape and wider)

Trailer 160 mm minimum,

Top Cover Tape

Components

100 mm Min. Leader 400 mm Minimum,

Figure 8 Maximum Camber

Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes

1 mm maximum, either direction

Straight Edge
250 mm

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

15

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Figure 9 Bulk Cassette Packaging (Ceramic Chips Only)

Meets Dimensional Requirements IEC-286 and EIAJ 7201
Unit mm *Reference
6 8 0.1 8 8 0.1 12.0 0.1
1.5 2.0 3.0
0.1 0 0 0.1 0.2 0

53 3* 31.5 0.2 0 36 0 0.2 19.0*

10*

110 0.7

5 0*

Table 9 Capacitor Dimensions for Bulk Cassette

Cassette Packaging Millimeters EIA Size Metric Size L Length Code Code
0402 0603 1005 1608 1.0 0.05 1.6 0.07

W Width
0.5 0.05 0.8 0.07

B Bandwidth
0.2 to 0.4 0.2 to 0.5

S Separation minimum
0.3 0.7

T Thickness
0.5 .05 0.8 .07

Number of Pcs/Cassette
50,000 15,000

Table 10 Capacitor Marking

Laser marking is available as an extra-cost option for most KEMET ceramic chips. Such marking is two sided, and includes a K to identify KEMET, followed by two characters (per EIA-198) to identify the capacitance value. Note that marking is not available for any Y5V chip. ln addition, the 0603 marking option is limited to the K only. (Marking Optional Not Available for 0402 Size)
Numeral Alpha Character
A B C D E F G H J K L M N P Q R S T U V W X Y Z a b d e f m n t y

Capacitance (pF) For Various Numeral Identifiers

9 0.1 0.11 0.12 0.13 0.15 0.16 0.18 0.2 0.22 0.24 0.27 0.3 0.33 0.36 0.39 0.43 0.47 0.51 0.56 0.62 0.68 0.75 0.82 0.91 0.25 0.35 0.4 0.45 0.5 0.6 0.7 0.8 0.9 0 1 1.1 1.2 1.3 1.5 1.6 1.8 2 2.2 2.4 2.7 3 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 2.5 3.5 4 4.5 5 6 7 8 9 1 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 25 35 40 45 50 60 70 80 90 2 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 250 350 400 450 500 600 700 800 900 3 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 2500 3500 4000 4500 5000 6000 7000 8000 9000 4 10000 11000 12000 13000 15000 16000 18000 20000 22000 24000 27000 30000 33000 36000 39000 43000 47000 51000 56000 62000 68000 75000 82000 91000 25000 35000 40000 45000 50000 60000 70000 80000 90000 5 100000 110000 120000 130000 150000 160000 180000 200000 220000 240000 270000 300000 330000 360000 390000 430000 470000 510000 560000 620000 680000 750000 820000 910000 250000 350000 400000 450000 500000 600000 700000 800000 900000 6 1000000 1100000 1200000 1300000 1500000 1600000 1800000 2000000 2200000 2400000 2700000 3000000 3300000 3600000 3900000 4300000 4700000 5100000 5600000 6200000 6800000 7500000 8200000 9100000 2500000 3500000 4000000 4500000 5000000 6000000 7000000 8000000 9000000 7 10000000 11000000 12000000 13000000 15000000 16000000 18000000 20000000 22000000 24000000 27000000 30000000 33000000 36000000 39000000 43000000 47000000 51000000 56000000 62000000 68000000 75000000 82000000 91000000 25000000 35000000 40000000 45000000 50000000 60000000 70000000 80000000 90000000

Example shown is 1,000 pF capacitor

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

16

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

Other KEMET Resources

Tools
Resource Configure A Part: CapEdge SPICE & FIT Software Search Our FAQs: KnowledgeEdge http://capacitoredge.kemet.com http://www.kemet.com/spice http://www.kemet.com/keask Location

Product Information
Resource Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Location

Product Request
Resource Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Location

Contact
Resource Website Contact Us Investor Relations Call Us Twitter www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir 1-877-MyKEMET http://twitter.com/kemetcapacitors Location

Disclaimer

All product specifications, statements, information and data (collectively, the Information) are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute and we specifically disclaim any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

C1025-1 10/12/2010

17

SMD MLCCs High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade)

KEMET Corporation World Headquarters

2835 KEMET Way Simpsonville, SC 29681 Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521

Europe
Southern Europe
Geneva, Switzerland Tel: 41-22-715-0100 Paris, France Tel: 33-1-4646-1009 Sasso Marconi, Italy Tel: 39-051-939111 Milan, Italy Tel: 39-02-57518176 Rome, Italy Tel: 39-06-23231718 Madrid, Spain Tel: 34-91-804-4303

Asia
Northeast Asia
Hong Kong Tel: 852-2305-1168 Shenzhen, China Tel: 86-755-2518-1306 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585

Corporate Offices
Fort Lauderdale, FL Tel: 954-766-2800

North America
Southeast
Lake Mary, FL Tel: 407-855-8886

Southeast Asia

Central Europe

Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817

Northeast

Landsberg, Germany Tel: 49-8191-3350800 Dortmund, Germany Tel: 49-2307-3619672 Kwidzyn, Poland Tel: 48-55-279-7025

Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642

Central

Schaumburg, IL Tel: 847-882-3590 Carmel, IN Tel: 317-706-6742

Northern Europe

Bishops Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Frjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000

West

Milpitas, CA Tel: 408-433-9950

Mexico

Zapopan, Jalisco Tel: 52-33-3123-2141

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com C1025-1 10/12/2010 18