Grundig Service Information

SERVICE INFORMATION
Product: TV's with Digi Basic chassis Television No. 1/97
Colour television receivers with Digi Basic chassis, e.g. ST 70-255 IDTV/LOG,
M 70-280 IDTV/LOG, SE 7089 IDTV/LOG
Possible complaint:
Brown colouration of the circuit board near the diode D 60222 BZT 03D180. Simultaneously
the "+Eco" voltage is approx. 5V too high.
Reason:
Coincidence of unfavourable component tolerances.
Cure:
Carry out the following changes in the stand-by mains stage:
- Change the Z-diode D 60203 from ZPD 9.1V to 8.2V.
- Change R 60202 from 68 kΩ to 1 kΩ.
- Connect an additional Z-diode ZPD 13 in series with R 60202. Connect the cathode of the
diode to the base of the transistor CT 60206.
- Check the rating of the resistor CR 60203 to be 2.2 kΩ.
Workshop:
Check the "+Eco" voltage. Carry out the changes if this voltage is higher than +17 V.
7
SI60201 D61001
T100mA BYT53B
6 2 1 5
R60201
CT60213
1k
R60213
n.V.
100
BC858B
BZT03D180
CR60214
TR60220
C60221
R60211
R60224
F
D60222
2,7M
C60201
100k
3,9n
68
F
5
1,5n CR60206 3 4 6
CD60201
LS4148
1k
R60212
R60221
2,7M
CC60203
M
330
100p
n.V.
CT60206 CT60203
BC858C BC848B
D60221
BA159
R60222
C60202 CR60202
330
+ D60202
BYT54K
D60224
1k ZPD13/2%
1u/63V T60223
CR60203
4 BUZ90A
2,2k
D
CD60202 3
P 2
LS4148 G S
100p/FKP1/1,6kV
CR60208
CD60223
CR60223
10n/1000V
ZPD8,2V
D60203
C60204
C60226
C60224
LS4148
10u/50V
F
+
220K
4,7k
n.V.
1
D60208
1N4001
R60207
4,7
P
D60207
1N4001
components to be
P
Bauteile
added or die zusätzlich
changed
einzubauen oder zu ändern sind.
Stores:
Z-diode ZPD 8.2 V part no. 8309-720-083
Z-diode ZPD 13 V part no. 8309-720-131
SMD resistor 1 kΩ part no. 8706-100-473
Technical Services / Information
8002/8012 S1/52067S0297
SERVICE INFORMATION
Product: TVR 3701 SV Television No. 2/97
Portable mono TV/VCR combination TVR 3701 SV
Possible complaint:
Mains voltage dependent chirp audible in stand-by mode.
Cure:
Fit an additional transistor stage as shown below into the power supply unit at IC 7310
(MC 44603 P).
2
3
Buffer
4
THERMAL
SHUTDOWN Vref Vcc
OVERVOLTAGE
CURRENT MANAGEMENT
SENSE
6
100 pF
IC 7310
MC 44603P UVLO1
Dmax & SOFT-SART
CONTROL
Vref
4,7 kΩ
CURRENT SENSE
INPUT
7 11
BC 548 B
3359
330
2320
BAT 85
1 kΩ
2,2 µ
fit these components

diese Bauteile
additionally
zusätzlich einbauen
Workshop:
Carry out when complaints are received.
Stores:
Diode BAT 85 part no. 8309-198-085
Technical Services / Information
8002/8012 52067S0397
SERVICE INFORMATION
Product: CUC 7301 Television No. 3/97
37 cm colour television receivers with chassis CUC 7301 text e.g.: P 37-730 text
Possible complaint:
Teletext operation is not possible in “AV” programme position.
Reason:
The video switch-IC 2807 (TEA 2114) is not fitted in 37 cm television receivers.
Cure:
Retrofit the following components:
IC 2807 TEA 2114
C 2815 1 µF
C 2810 100 µF
C 2811 0.1 µF
CR 2813 270 Ω
CR 2814 270 Ω
In addition, change the polarity of 2.2 µF electrolytic capacitor C 2816 (negative terminal to
pin 8 of IC 2810) and remove bridge BR␣ 056. BR009
15 16 17 19 36 37 18 35 11 26 6 1 27
34 10
G
BLANK
R
RGB-REF
33 20
32 4
BR 056
31 5
IC 2810
30 SAA 5254 P/E 14
OSC OUT
29 38
OSC IN
28 39 M
8 12 13 22 24 25 23 21 2 3 7 40 9
1
4 2
0dB
2,2u/100V
C2816
IC 2807
+
3
0dB
6 270
TEA 2114
8 CR2813
6dB
100u/25V
C2810
CR2814
7 5 2,2n
270
M
+
CC2810
CC2811
0,1u
1u/100V
C2815
CR2807
47k
+
EURO-AV
VQ
SYNC
SYNC
FBAS
FBAS
SC
V
U
Workshop:
The circuit board is already prepared to be fitted with these components.
Stores:
IC TEA 2114 part no. 8305-362-114
Electrolytic capacitor 1 µF/100 V part no. 8452-967-325
Electrolytic capacitor 100 µF/25 V part no. 8452-967-135
Capacitor 0.1 µF part no. 8555-267-173
SMD resistor 270 Ω part no. 8706-297-059
Technical Services / Information 8002/8012 52097S0497

Service Information
Product Colour television receivers with chassis CUC 7303 and 7305, e.g. P 37-071,
TV
T 51-720 text, T 55-731 text
Possible complaint:
After having replaced EEPROM IC 830 X24C02, the Automatic Tuning
System does not find all stations.
Reason:
The EEPROM on this chassis contains information about so-called band
limits in its memory cells 235 to 239. These values are programmed in the
factory in a special alignment adapter and vary with the individual tuner
and Z-diode D 683 (ZTK 33). When fitting a new EEPROM, any value is
stored in the memory cells. Consequently, the ATS does not scan the
complete frequency range.
Cure:
Clear the band limit values (content of the memory cells 235 to 239) as
follows:
1. Call up the Service Menu (depress button „i“ on the remote control
while switching on with the mains switch).
2. With the remote control buttons „P+/P-“ select line „AGC ALIGN“.
3. During a period of 5 seconds operate the buttons „AUX“ and „OK“
sequentially.
The ATS search function now scans the whole frequency range.
Note: When the band limits are cleared individual stations may be found
twice!
Workshop:
Clear the band limit values when having replaced the tuner, Z-diode
D 683 or EEPROM IC 830.
Stores:
none Serial No 5/97
Note to our Service Information 1/97 (subject: Digi Basic colour television
receivers - „Eco“ voltage is about 5V too high)
Due to repeated inquiries we would like to point out that resistor R 60202
that is to be changed from 68 kΩ to 1 kΩ is a lead-type version and not a
SMD component.
Central
52127S0997, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with chassis CUC 7350, e.g. ST 55-750 text
TV
Possible complaint:
Despite the modifications carried out according to our TV Service
Information 9/96 the television sets switch occasionally to Standby
after a prolonged time of operation.
Reason:
Temperature drift of the +E operating voltage by about 0.2 to 0.3V
caused by Z-diode CD 61023. Consequently, IC 34015 TDA 8374
switches off with sudden black/white changes in the picture content or
changing scenes.
This Z-diode has been introduced later and therefore is drawn in only
in the 1st Supplement to the CUC 7350 Service Manual.
Cure:
The position of the Z-diode is X=10, Y=150. Unsolder this diode and
insert a SMD resistor 1206 1.2Ω 1% in this place.
Stores
SMD resistor 1206 1.2Ω 1% part no. 8706-297-475
Lötseite
Copper Side
Serial No 6/97
150
10
Central
S2R1521370000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with chassis CUC 7300, e.g. P 37-740 SAT, and all
TV
sets retrofitted with the built-in satellite receiver SER 7300
Possible complaint:
The sound disappears suddenly during the reception of a satellite
programme and is audible again only when changing the programme or
switching the TV off and on again.
Reason:
IC MSP 3400 on the SAT Module hangs up by static charges entering the
Reset input of the IC.
Cure:
Unsolder the SMD capacitor CC 3800 from its place on the SAT Module
and resolder it at the place indicated on the figure below.
CC 3800 an dieser
Position ausbauen
Unsolder CC 3800
CC 3800
Resolder an dieser
CC 3800 at
thisPosition
place auflöten
R3903
CC3802
CC3801
CBR67 CR3906 CC3903

CBR56
CBR59
CBR63
CR3915
CBR69
CR3807
CBR62 CBR66 CC3803

CBR54 CR3804
CR3801 CC3800
CBR64
CC3974 CBR51
CC3976
CC3804
CR3800 CR3908
CBR52
CC3945
CBR58
CR3945 28 15
CR3941 CIC3800 CR3891
CC3947
CC3806
CBR53
CT3945
CR3947 1 14 CBR49
CC3948
CBR50
CBR44
CBR31
CR3960 CBR57 CBR41

CBR3
CBR40 CBR48
CBR30
CC3975
CBR61
CR3946
CBR47
CBR55
CT3947
CBR43
CR3961
CR3962
CC3961
CBR37
CR3943
CBR74 CBR42 CBR39

CR3942
CC3966
CR3802
CBR45
CBR34
CC3958
CR3950 CBR38
CC396
CBR2
CBR3
Serial No.7/97
CR3949
CC3967 CR3907 CBR33
CBR46
Stores:
none
Central
S3/521570000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with chassis Digi Basic CUC 1825, 1826 and
TV
1827, e.g. ST 63-255 IDTV/LOG, M 70-281 IDTV/LOG, SE 7089 IDTV/LOG
Possible complaint:
The TV receiver can be switched on only with the remote control handset.
When switching on with the mains switch, the receiver always goes to
Standby mode.
Reason:
Unwanted activation of the protection circuit at the moment the TV
receiver is switched on.
Cure:
Change the electrolytic capacitor C 58004 (on pin 6 of IC 58010) from
10 µF to 22 µF/25V.
Workshop:
Important note: Since the Digi Basic TV receivers work without a wiper
contact in the mains switch the EEPROM stores the operating mode
(Standby or „On“) at the time the set is switched off with the mains
switch. That is why the set will only start with „On“ the next time it is
switched on (power on) if it was switched off from this mode.
Stores:
Electrolytic capacitor 22 µF/25V part no. 8452-967-126
Serial No 8/97
Central
1/1
Service Information
Product Colour television receivers with Digi 6 chassis - CUC 1952, 1983, 1984 with
TV
built-in SER 150/SER 150 ET Satellite Receiver - e.g. Denver SE 8216/9
Ref./PIP, M 82-269/9 Reference
Possible complaint:
On reception of the channel Premiere via satellite the connected decoder
does not operate while this station is decoded perfectly when received via
a cable installation.
Reason:
The video crossbar IC TDA 6417 is overloaded on satellite reception.
Cure:
Change the SMD resistor CR 43209 from 1 MΩ to 470 kΩ. It is also
possible to connect another 1 MΩ resistor in parallel when carrying out
repairs.
Workshop:
The position of the SMD resistor is X=102, Y=187.
Stores:
SMD resistor 470 kΩ 0805 part no. 8706-100-337
SMD resistor 1 MΩ 0805 part no. 8706-100-145
Serial No 9/97
Central
1/1
Service Information
Product Mono TV Recorders TVR 3710, 5100 and 5500
TV
Possible complaint:
TV Recorder does not operate.
Reason:
Defect in transistor 7352 (MTP 3055E) caused by static discharges in the
TV Recorder.
Cure:
Fit an additional Z-diode BZX 83B15 between gate and source to suppress
voltage peaks at the gate.
Workshop:
The Z-diode must strictly be retrofitted if the transistor 7352 fails. This
change is carried out already in the factory.
Stores:
Z-diode BZX 83B15 part no. 8309-720-115
5D1
BZX 83B15
MTP zusätzlich
fit einbauen
additionally
3055E
3354
14H
G D S
220 k
Serial No 10/97
7352
MTP 3055E
LM317T
3353
1k
7351
BC 548B
Central
522370000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with Digi IV chassis - CUC 1821/1851/1881/1892
TV
and 1981, e.g. M 70-781 IDTV, M 70-791 IDTV, M 82-102 IDTV, M 95-102 IDTV,
M 82-169 PALplus
Possible complaint:
Mains supply switching transistor fails occasionally.
Reason:
Breaks may be found after a long time of use at the solder pads in the area
of the mains supply stage especially at the connections of the mains supply
transformer.
Cure:
Re-solder the connections in this area.
Workshop:
For reasons of operational reliability and irrespective of the fault, re-solder
the 1.5Ω resistor R 622 and the choke L 663 (both components are in the
area of the mains supply) with great care using ample tin.
Stores:
None
Serial No 11/97
Central
1/1
Service Information
Product Colour television receivers with 82/70 cm Toshiba picture tube and Digi 6
TV
chassis - e.g. M 82-269/9 Ref, SE 8216/9 Ref/PIP, M 70-269/9 Ref, SE 7016/9
Ref/PIP Trento
Possible complaint:
Audible hum or buzzing noise from the bass loudspeaker.
Reason:
Magnetic radiation from the deflection yoke into the loudspeaker.
Cure:
To reduce the radiation from the yoke exchange the bass box loudspeaker
for a type with compensating coil.
Workshop:
Stores:
Loudspeaker with compensating coil, part no. 19154-031.61
Product Colour television receivers with Digi Basic chassis CUC 1805/1825/1826
and 1827, eg. ST 63-255 IDTV/LOG, ST 72-261 IDTV/LOG, Boston SE 7090
IDTV/LOG
Possible complaint:
TV set does not start occasionally.
Reason:
„Cold“ solder connection of the wire bridge „BR 129“ with the earthing pad
Serial No. 12/97

on the component side in the area of the mains supply stage. Consequently,
the standby power supply does not start up reliably.
Workshop:
Re-solder the chassis connection in every television receiver coming in for
repair using ample solder tin.
Stores:
None
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 7301/7301F, e.g. P 37-070,
TV
T 51-730 text, T 55-730/5 text
Possible complaint:
No picture. High tension is available.
Reason:
The transistors CT 181, CT 186, CT 191 and CT 193 failed because of high
voltage sparks inside the picture tube.
Cure:
Replace the defective transistors and solder an additional diode 1N4148
from pin 7 of the „RGB“ lead (to picture tube panel) to the ground pin 4 on
the chassis. Connect the anode of the diode with pin 4.
Workshop:
Fit the additional diode when the transistors failed.
Stores:
Diode 1N4148 part no. 8309-215-045
Product Correction of Service Information 9/97

Colour television receivers with Digi 6 chassis 1952, 1983, 1984 and built-in
satellite receiver SER 150/SER 150 ET - e.g. Denver SE 8216/9 Ref./PIP,
M 82-269/9 Reference
Possible complaint:
On reception of the channel Premiere via satellite the connected decoder
does not operate while this station is decoded perfectly when received via a
Serial No 13/97
cable installation.
Reason:
The video crossbar IC TDA 6417 is overloaded on satellite reception.
Cure:
The change of the resistor CR 43209 from 1 MΩ to 470 kΩ as described in
our Service Information 9/97does not produce the desired effect in every
case. Therefore change the resistor CR 43209 from 1 MΩ to 330 kΩ when
carrying out repairs. It is also possible to connect a 560 kΩ resistor in
parallel with the 1 MΩ.
Workshop:
The position of the SMD resistor is X = 102, Y = 187.
Stores:
Central
R2S7/523070000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with chassis CUC 7303, e.g. P 37-731 text,
TV
P 45-731 text, T 55-731 text
Possible complaint:
Pronounced NF crackling when switching off with the mains switch.
Cure:
Change the Z-diode D 323 from ZPD 8.2V to 9.1V 2%. Additionally, solder a
diode 1N 4148 in parallel with the resistor CR 323. Connect the cathode of
this diode with the +B voltage.
Workshop:
Carry out on request. This change has already been introduced in
production.
Stores:
Z-diode ZPD 9.1V 2% part no. 8309-720-092
Diode 1N4148 part no. 8309-215-045
Product Colour television receivers with chassis CUC 7303/7305/7350 and the
picture tube panels 29305-022.16/-022.17, e.g. P 37-731 text, P 45-731 text,
T 55-731 text, P 37-731/12 text, ST 55-750 text, XS 55/1, Lissabon SE 5576
text
Possible complaint:
Failure of the RGB output stages (picture tube panels 29305-022.16 and
-022.17) or of the teletext function.
Reason:
The semiconductors are destroyed by high-voltage sparks within the picture
tube.
Cure: Serial No 14/97

On the picture tube panels -022.16/-022.17, insert an additional 1.5 kΩ
composite carbon resistor (do not use a carbon film resistor!) into the circuit
path to the screen grid connection of the picture tube socket. Ensure that
the break is 2mm wide at least (see figure) to avoid sparking.
additional resistor
Workshop: zusätzlicher Widerstand
Refit the resistor in any case if the above
mentioned semiconductors failed.
Stores: 7
Only altered picture tube panels break
Trennstelle
29305-022.16/-022.17
Composite carbon resistor 1.5 kΩ,
part no. 8702-401-077.
Central
R3S8/523970000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with Digi 6 chassis CUC 1842, 1894, 1952, 1962
TV
and 1983, e.g. M 72-410 Ref., Denver SE 8216/9 PAL Plus, M 70-269/9 Ref.
Possible complaint:
Vertical output stage TDA 4173 fails or thin white lines similar to retrace
stripes are visible.
Reason:
Inherent instability of the vertical output stage IC TDA 4173 AF.
Cure:
- Should above mentioned symptoms appear do not fail to exchange
TDA 4173 AF and solder additionally a 1 nF foil capacitor from pin 1 and
from pin 7 each to pin 4 (-K voltage) on the copper side.
- Check the mounting position of the vertical output-IC. If the position of
the IC is too low, the pins may temporarily come into contact with
the chassis connection on the upper side causing the IC to fail.
Additionally, the circuit may already be damaged by the building up
force of pressure resulting in a long-term failure. Therefore replace
TDA 4173 AF also if it has not been fitted correctly!
Workshop:
When fitting the new IC TDA 4173 AF take care of the correct position of the
holding clamp and solder in the additional capacitors!
This change has been generally introduced.
Stores:
Foil capacitor 1 nF part no. 8555-367-525
IC TDA 4173 AF part no. 8305-344-173
Serial No 15/97
correct position position is too low

richtige Montage zu tiefe Montage
≈5
Central
1/1
Service Information
Product Colour television receivers with Digi Basic and Digi 6 chassis - CUC 1805,
TV
1825, 1826, 1827, 1828, 1842, 1894, 1952, 1962 and 1983
e.g. M 72-410 Ref., Denver SE 8216/9 PAL Plus, M 70-269/9 Ref.
Possible complaint:
Interference lines in the picture or complete failure of the tuner.
Reason:
Failure of the PLL-IC TY 44860 within the tuner.
Cure:
After having replaced the tuner, solder an additional Z-diode ZPD 33 B
(2% tolerance) on the copper side of the chassis board from pin 1 to the
multipoint connector of the signal module to chassis (anode to chassis).
Workshop:
Retrofit the Z-diode if the tuner failed.
Stores:
Z-diode ZPD 33 B (2%) part no. 8309-707-135
Serial No 16/97
Central
G1/524170000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with Digi Basic chassis - CUC 1806, 1825, 1826,
TV
1827, 1829, 1830 with the picture tube panels 29305-122.04/-122.10/-122.12
and -122.17
e.g. ST 70-255 IDTV/LOG, ST 72-261 IDTV/LOG, Atlanta SE 7220 IDTV/LOG,
ST 72-261 IDTV/LOG
Possible complaint:
Failure of the RGB output IC‘s TDA 6111.
Reason:
The RGB output IC‘s are destroyed by high voltage sparks.
Cure:
Directly from the outputs (pin 8) of the three output IC‘s TDA 6111 connect
one additional diode BAV 21 each to chassis and one diode each to the
+200 voltage (see figure).
Workshop:
The insertion of the three diodes which are to be connected to +200 is
already prepared on the picture tube panel by the diodes D 734, D 754 and
D 774.
The three diodes which are to be connected to chassis are to be soldered on
to the copper side from pin 8 to pin 4 (anode to pin 4).
Stores:
Diode BAV 21 part no. 8309-200-021
IC TDA 6111 part no. 8305-336-111
Only modified picture tube panels 29305-122.04/-122.10/-122.12 and
-122.17.
+12V +200
2 6
Serial No 17/97
additional
zusätzliche
3
Dioden
diodeBAV
BAV 21
21
9 8 zur
to picture
tube
Bildröhre
1 7
TDA 6111
TDA 6111
Central
G2S9/524170000, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers ST 72-261 IDTV/LOG and ST 72-261/8 IDTV/LOG
TV
with Toshiba picture tube
Possible complaint:
Picture seems to be unsharp or the TV switches occasionally to Standby.
Reason:
Short circuit in the serially connected capacitors C 64001 and C 64002
(150pF/6kV each) on the dynamic focusing board.
Cure:
1. Replace the capacitors C 64001 and C 64002 on the dynamic focusing
board.
2. Check the Ug2/focus control unit on the picture tube socket board
29305-122.12.
If the TV is fitted with version 29201-361.01 or -361.11, this focus control
unit must be replaced by version 29201-361.04. Version 29201-361.20
needs not to be replaced but can remain in the TV set.
3. Attention: When fitting the new Ug2/focus control unit, please note the
following wiring instructions:
- Insert the blue lead - provided with a white mark - of the Ug2/focus
control unit into the focus voltage connection of the diode split
transformer.
- Solder the shorter blue lead of the Ug2/focus control on to the focus
voltage connection of the focusing board.
- Route this lead from the focusing board to the focus voltageconnection
of the picture tube socket.
- Re-attach the cover of the focusing board.
4. Replace the diode split transformer 29201-680.01. Due to the failure of
the capacitor C 64001 or C 64002 the resistance of the focus resistor
in the diode split transformer changes so that an optimum adjustment of
the picture sharpness is no longer possible.
Serial No 18/97
Workshop:
Please check the wiring of the focus leads according to point 3 of every
TV receiver of type ST 72-261 IDTV/LOG and ST 72-261/8 IDTV/LOG coming
in for repair!
Focus adjustment:
- Feed in a convergence test pattern.
Set contrast to maximum. Set the brightness so that the black
background of the test pattern just becomes visible.
- With the focus control on the picture tube socket board, adjust the
horizontal lines for maximum sharpness.
- Afterwards, adjust the vertical lines with the focus control on the
focusing board for maximum sharpness.
- Repeat this adjustment to achieve the best result possible.
Stores:
Capacitor 150pF/6kV part no. 8502-200-066
Ug2/focus control unit part no. 29201-361.04
Diode split transformer part no. 29201-680.01
Dynamic focusing board part no. 29305-025.26 Central
1/1
Service Information
Product Satellite Receivers STR 631/632/641 and 642
TV
Possible complaint:
No sound after the receiver has been operated in standby mode for a
prolonged period of time. The sound is audible again only on disconnecting
the mains plug and switching the satellite receiver on again.
Reason:
As advised by our Service Information 4/97, this phenomenon is caused by
IC STV 400 STV 0056A but cannot be limited to certain IC lots.
Cure:
Solder one SMD Z-diode 8.2V each in parallel with the electrolytic
capacitors C 427 (pin 49 IC400) and C 436 (pin 38 IC400) which are
connected to chassis.
Workshop:
The additional Z-diodes can be soldered on to the copper side directly
between the connections of the electrolytic capacitors (anode to negative
connection of the electrolytic capacitor).
Retrofit the diodes in every satellite receiver coming in for repair.
Stores:
SMD Z-diode 8.2 C part no. 8309-455-082
Serial No. 19/97
Central
1/1
Service Information
Product Colour television receivers MW 70-100/8, M 72-100 and M 72-100/8
TV
Possible complaint:
Audible buzzing noise that does not come out from the loudspeaker.
Reason:
The mains suppressor chokes on the mains switch module may be in
contact with the protective screen producing vibrations thereby.
Cure:
Unsolder the protective screen and the mains suppressor choke and fit a
suppressor choke with part number 29500-834.97. Since this choke is
provided with an additional compensating coil the protective screen is no
more needed.
Workshop:
Carry out on request.
Stores:
Mains suppressor choke part no. 29500-834.97
Serial No. 20/97
Central
1/1
Service Information
Product Colour television receivers with Digi Basic chassis - CUC 1825 and 1826, e.g.
TV
ST 63-255 IDTV/LOG, Boston ST 270 IDTV/LOG, ST 72-261 IDTV/LOG
Possible complaint:
Audible short noise building up when switching off with the mains switch.
Cure:
Solder an additional diode 1N4148 (cathode to pin 5) between pin 81 and
pin 5 of the processor CIC 80050.
Workshop:
Stores:
Diode 1N4148 part no. 8309-215-045
Product Colour television receivers with chassis CUC 2030 - ST 63-700 text and
ST 70-700 text
Possible complaint:
Vertical jittering of the videotext and menus displayed on the screen.
Reason:
The vertical sync pulse at the input of processor CIC 81050 pin 46 is
compressed.
Cure:
Switch an additional 120 kΩ resistor from the base of CT 46009 to chassis.
Workshop:
Carry out on request. This modification has generally been introduced. Serial No. 1/98
Stores:
None
Central
1/1
Service Information
Product Risks of failure of electric connections (solder pads) caused by ageing
TV
For reasons of thermal load and mechanical stress solder pads at positions
where high voltages and /or currents are effective involve special technical
problems.
In this connection we would like to refer you to our Service Information

bulletin „General 1/95“ which dealt in great detail with this subject.
Solder pads which should be checked with special care in every set coming
in for repair are for example:
- within the line output stage, the connections of line and diode split
transformers, connecting pins of the yoke plug, components of the +A
supply rail as well as the capacitors and coils within the deflection circuit.
- within the mains supply stage, the transformer connections, the
connections of the rectifier and charging capacitor as well as the
connections of the stabilizing ICs.
Product Satellite Receivers - memory EEPROMs
The part numbers of the memory ICs specified in the Service Manual are not
correct.
The preprogrammed EEPROMs are available under the following part
numbers:
Stores:
STR 641 IC 601 part no. 72008-668.6900
STR 642 IC 601 part no. 72008-688.7000
STR 642 IC 602 part no. 72008-688.7100
STR 100 DX CIC 1420 part no. 72008-668.7200
STR 110 CIC 1420 part no. 72008-668.7300
Serial No. 2/98
Product Correction of Service Information bulletin 12/97

Colour television receivers with 82/70cm Toshiba picture tubes and Digi 6
chassis, e.g. M82-269/9 Ref, SE 8216/9 Ref/PIP, M 70-269/9 Ref, SE 7016/9
Ref/PIP Trento - Hum and buzzing noise
The part number of the loudspeaker with compensating coil specified in the
Service Information is not correct. The correct number should read 19154-
043.6100. Please correct your documents.
Central
1/1
Service Information
Product Colour television receivers P 37-731 text and P 45-731 text with CUC 7303 text
TV
Possible complaint:
Teletext information cannot be received via the Euro-AV connection, for
example when connecting a Grundig Micro-Sat Receiver.
Cure:
For activating the teletext mode in „AV“ progamme position retrofit the
following components:
- IC 2807 TEA 2114
- C 2815 1µF/100V
- C 2810 100µF/25V
- CC 2811 0.1µF
- CR 2814 390Ω 5% (structural shape 0805)
- CR 2813 change from 0Ω to 270Ω 5% (structural shape 1206)
- Solder a wire bridge BR 077 (+B‘ voltage to IC 2807 pin 7)
- Unsolder the electrolytic capacitor C 2816 and re-solder it to position
C 2817 (positive connection to pin 30 of processor IC 850).
- Remove the bridge BR 056.
Workshop:
The circuit board is already prepared for fitting the components.
The steps for retrofitting television receivers with chassis CUC 7301 are
described in our Service Information TV 3/97.
Stores:
IC TEA 2114 part no. 8305-362-11400
Electrolytic capacitor 1µF/100V part no. 8452-967-32500
Electrolytic capacitor 100µF/25V part no. 8452-967-13500
SMD capacitor 0.1µF part no. 8672-167-18700
Serial No. 3/98
Central
1/1
Service Information
Product Colour television receivers with chassis Digi Basic (CUC 1805/1825), Basic+
TV
(1826/1827) and Basic++ (1806/1828/1829/1830)
e.g. M 70-280 IDTV/LOG, ST 72-261/8 IDTV/LOG, M 72-100, Atlanta SE 7220
IDTV/LOG, ST 70-270 IDTV
Possible complaint:
When switching on with the mains switch the television receiver goes to
Standby and cannot be switched on again with the remote control handset.
Reason:
Failure of transistor CT 80085 BC 858B (position X=148, Y=18).
Cure:
On replacement of the transistor, solder an additional diode 1N4148 from
the base to the emitter (anode to base) of CT 80085 and change the resistor
CR 80083 from 0 Ω to 47 Ω 5% (structural shape 0805).
Workshop:
The additional diode can be fitted to the solder side between the base of
CT 80085 and the cathode of diode CD 80081.
Stores:
Transistor BC 858B part no. 8301-003-85800
Diode 1N4148 part no. 8309-215-04500
+H
+N
Serial No. 4/98

2 ICIC80040 1
change
CR 80083 MC 80040
33164
MC 33164
CR 80083
von 0 Ω in
from 0Ω
to Ω
47 47ändern
Ω
3
zusätzliche
additional
diode
Diode
1N4148
1N4148
CT
CT80085
80085
BC
BC858
858BB
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 2030, 2031, and 2040
TV
e.g. ST 63-700 text, ST 63-710, Melbourne SE 7210 TOP, ST 70-700 NIC/text
Possible complaint:
No programmes receivable.
Reason:
Failure of diode D 31001 ZTK 33B caused by too high a Zener current.
Cure:
On replacement of the the Z-diode ZTK 33B, change additionally the SMD
resistor CR 31009 from 330 Ω to 680 Ω 5% (structural shape 0805) and
solder an additional 0.1µF foil capacitor in parallel with Z-diode ZTK 33B.
Workshop:
When the Z-diode failed, change the resistor (position X=78, Y=10) and
solder an additional capacitor.
Stores:
Z-diode ZTK 33B part no. 8305-306-00100
+45V
+45V
change
CRCR31009
31009
von 330
from Ohm
330 Ω
into680 DD31007
31007
680Ohm
Ω ändern ZPD4,7V
ZPD 4.7V
Serial No. 5/98

CT
CT31005
31005
BC 858 B
BC858B
0,1 µ
0.1µ
fit
zusätzlich
additionally
einbauen
+33V
DD 31001
31001
ZTK33B
ZTK 33 B
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 6360 and 6365
TV
e.g. SE 6376, ST 63-761 TOP, ST 70-755 TOP, XS 70/1, ST 72-761 TOP
Possible complaint:
Tearing of the displayed menus and teletext pages.
Reason:
Failure of the capacitors C 683 and C 684 of 0.1 µF each.
Cure:
Change the electrolytic capacitors C 681 and 682 of 220 µF/16 V each in
addition to the capacitors C 683/684.
Stores:
None.
+H (+5 V)
220µ/16V
C 684
C 682
0,1 µ
6
L 678 IC 680
1 TDA 8137
4 3 7
C 679
+5V/D
220µ/16V
C 683
C 681
0,1 µ
C 680 T680
Serial No. 6/98

2,2n BC548B
Central
1/1
Service Information
Product Colour television receivers with chassis Digi Basic/Basic+/Basic++
TV
CUC 1805, 1806, 1825, 1826, 1827, 1828, 1829 and 1830
e.g. ST 63-255 IDTV/LOG, ST 72-261 IDTV/LOG, Boston SE 7090 IDTV/LOG,
Atlanta SE 7220 IDTV/LOG
Possible complaint:
Jittering of the displayed menus or teletext pages when the television
receiver has warmed up.
Reason:
Lack of stability of the oscillator circuit at processor-IC IC 80050.
Cure:
Change the SMD capacitors CC 46021/46022 to a 56 pF version each
(structural shape 0805).
Workshop:
Carry out this change when complaints are received.
Position CC 46021 X=93, Y=81
Position CC 46022 X=96, Y=81
Stores:
None.
e.g. ST 63-700 text, ST 70-780 text, Melbourne ST 7210 TOP,
ST 70-700 NIC/FT
Possible complaint:
Jittering of the displayed menus and teletext pages.
Reason:
Limited vertical sync pulse on pin 46 of the processor-IC IC 81050. Serial No. 7/98
Cure:
Connect an additional 120 kΩ resistor from the base of CT 46009 (BC 848,
position X=146, Y=63) to chassis.
Workshop:
Stores:
None.
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 63xx, 64xx, 20xx and Digi Basic/
TV
Digi 6 - new plug-in systems
The television receivers with above mentioned chassis are partly

fitted with new plug-in systems between the modules and the chassis.
As a consequence of this conversion, the modules with the new systems
can no longer be pulled out of the chassis as usual. When trying to do
so damages may be caused to the module or the chassis.
The following figures show the different systems and how they can be
dismounted.
1. The traditional black socket terminal

strips of the modules are additionally
provided with locking lugs which, in
addition to a module holder, prevent
the module from slipping out. The
module can be dismounted from above
or below by pressing the locking lugs
together.
Fig. 1
2. The modules of the colour television receivers with chassis CUC 20xx
are fitted with a new plug-in system. They can be dismounted by
disengaging the locking lug with a screw driver. In future, it will also be
possible to release the lugs from below through additional drilled
holes in the chassis.
Serial No. 8/98
Fig. 2
3. Concerning the Feature Boxes on the Digi Basic and Digi 6 chassis:
Please note that in contrast to our earlier Digi chassis (Digi 3, 4 and 5)
the two earth lugs of the Box for interference protection are
soldered in. In the case of any defect, these lugs must be
unsoldered!
Central
1/1
Service Information
TV
e.g. ST 63-700 text, ST 70-780 text, Melbourne SE 7210 TOP, ST 70-700 NIC/FT
Possible complaint:
Programme position number (e.g. „P 14“) is continuously displayed on the
screen.
Reason:
When having pressed the „i“ button on the remote control handset no
further command is entered during a period of about 6 seconds. As a result,
the TV set switches over to the continuous display mode so that the
programme position number is continuously visible on the screen. As this
function is not mentioned in the product descriptions, it may happen in a
few cases that consumers think it to be a fault.
Cure:
Cancelling the continuous display mode:
Call up the „Dialog Center“ menu with button „i“ and press this button a
second time during a period of 6 seconds.
Stores:
None
Serial No. 9/98
Central
1/1
Service Information
Product Colour television receivers with chassis Digi Basic, Basic+ and Basic++
TV
CUC 1805, 1825, 1826, 1827, 1828
e.g. ST 63-255 IDTV/LOG, M 70-280 IDTV/LOG, Atlanta SE 7220 IDTV/LOG,
Sydney 100 SE 7020 IDTV/LOG
Possible complaint:
Interference in FM reception in the immediate vicinity (approx. 2m) of a
switched on television receiver.
Cure:
The interference level can be reduced noticeably by soldering in an
additional ground-to-ground connection.
Workshop:
Solder an insulated wire of approx. 35mm (2.5mm2) in length on to the
solder side of the mains supply section (between pos. R60007 and C60001)
as shown below. This additional wire is used to short-circuit the ground loop
which has been found to be the source of interference.
Carry out this change with extreme care (primary side - VDE safety
regulations!) and fix the wire additionally with a heat-set adhesive!
Stores:
None
Solder
Brückein zwischen
a bridge between
diesen
these points and fix it und
Punkten einlöten with amit
heat-set adhesive
Heißkleber fixieren
Serial No. 10/98

0123456789
Central
G3/52158S0398, 8002/8012 After-Sales Service
1/1
Service Information
Product Colour television receivers with chassis CUC 2030
TV
e.g. ST 63-780 text, ST 70-700 NIC/TOP, ST 70-780 text, Greenville 7003 text,
Melbourne SE 7210 TOP
Possible complaint:
Moiré patterning / interferences similar to pearl strings visible in the picture
of stations in the lower special channels (S05, S06, S07).
Reason:
Harmonics from the switched mode power supply entering via insufficiently
screened or defective aerial connecting cables.
Cure:
Use an aerial cable with double screening! In special cases, an absorber
cable („100 Hz aerial connecting cable), order number 29210 435 0100, may
be necessary.
If the fault is not yet completely eliminated, carry out the following changes
in the circuit:
1. Solder the „hot“ contact of the capacitor C 60009 (220pF/2kV)
directly to pin 1 of the transformer TR 61001.
2. Connect the earthing area on the upper side (component side) within
the power supply section with the earth tag on the solder side.
For this solder a short piece of wire to the earth connection of R 60014
(not fitted) and contact it with the earthing area on the upper side. To
ensure that the wire is reliably in contact with the earth, remove the
solder resist and bend the wire down by a length of about 5mm.
Workshop:
To connect the capacitor C 60009 directly to pin 1 of the transformer
TR 61001 proceed as follows:
- Interrupt the circuit path between C 60009 and L 60006.
- Fit the wire bridge „BR 145“. It is located between C 60009 and L 60006
Serial No. 11/98

(sometimes also designated „BR 6008) and connect the separated end of
the capacitor with the bridge (bend the connecting wire of the bridge
towards the capacitor).
Carry out these changes with extreme care (VDE safety regulations)!
Stores:
None
Central
1/1
Service Information
Product Defective modules returned for repair within our repair exchange system
TV
A relatively great number of the defective modules coming in for repair is
returned without the fault tag!
This makes work more difficult for us because the defect complained of
could be a hidden fault that shows only occasionally. Please help us
discovering hidden faults by sending in the defective module together with
the fault tag. A fault tag is enclosed with each replacement module.
In this connection we want to point out to the observance of the generally

known MOS safety instructions („Safety“ Service Manual).
These instructions apply also to the handling of defective modules.
- When returning defective modules please use generally the MOS
protective packing enclosed with the replacement module.
- Even defective MOS components must never be stored or transported in
styroper material or in plastic magazines.
- Persons handling MOS components must first discharge any electrostatic
charge on their body or clothing by touching a grounded object.
Stores:
„Safety“ Service Manual part no. 72010 800 0000
Serial No. 12/98
Central
1/1
Service Information
Product Grundig built-in Satellite Receivers SER 150, SER 151E and SER 150ET
TV
Differences and possible use of the receivers for colour television receivers
with chassis Digi Basic, Basic+, Basic++ and Digi 6
Common to all of the satellite retrofitting kits SER 150, SER 151E and SER
150ET is the Sat module 29504-106.24. The differences are the EPROM‘s
included in the delivery of the retrofitting kits.
SER 150 no EPROM included (no longer available)

SER 151E one EPROM included for TV‘s with Digi Basic chassis
SER 150ET two EPROM‘s enclosed; one each for TV‘s with chassis Digi
Basic/Basic+ and chassis Digi 6
The retrofitting kits SER 150 and SER 151E were replaced by SER 150ET and
are no longer available.
The EPROM‘s of SER 150ET, the only version available, can be used for the
following chassis:
1. EPROM with order no. 19798-300.xx for the chassis Digi Basic/Basic+
CUC 1805, 1825, 1826, and CUC 1827
2. EPROM with order no. 19798-311.xx for the Digi 6 chassis
CUC 1842, 1894, 1952, 1983, and CUC 1984
Attention!
The EPROM in television receivers with the chassis Digi Basic++ CUC 1806,
1828, 1829, 1830, 1836 and CUC 1929 needs not to be replaced.
None of the EPROM‘s enclosed must be fitted to these chassis!
Serial No. 13/98
Central
1/1
Service Information
Product Colour television receivers M 84-210/8a IDTV/LOG - CUC 1829 (Digi Basic++)
TV
Possible complaint:
Dependent on the picture content (black/white changes) these TV sets
switch occasionally to Standby.
Cure:
Change the resistor CR 21234 from 220 Ω to 390 Ω.
Workshop:
Stores:
SMD resistor 390 Ω 5% 0805 part no. 8706 100 06300
Serial No. 14/98
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 7303, e.g. P 37-830 text,
TV
T 51-071, T 51-731 text, T 55-830/4 text
From September 1998 onwards, colour television receivers with the CUC
7303 chassis have been fitted with a reworked chassis CUC 7303. It is
provided with a new processor and a few changes were made in the
peripheral circuit of the computer.
The television receivers with the reworked chassis are marked with a
Version Number „VN...“ printed on the label on the back of the receiver (see
figure).
Gerätetype
Type of product
T 51-731 text
220-240V~ 50/60Hz 55W
EIGENSICHERE KATHODENSTRAHLRÖHRE NACH ANLAGE III
DER RÖNTGENVERORDNUNG.
VNA
BESCHLEUNIGUNGSSPANNUNG MAX. 25kV, 1.0mA.
TUBOS DE RADIACIÓN CATÓDICA AUTOLIMITADA, SEGÚN ANEXO III DE LA NORMATIVA
RADIOLÓGICA. TENSIÓN DE ACELERACIÓN MÁX. 25kV, 1.0mA.
ATENCION! NO ABRIR SIN ANTES DESCONECTAR LA TENSION DE RED.
Version number
STACCARE LA SPINA DI RETE PRIMA DI TOGLIERE IL PANNELLO POSTERIORE.
PROTEGGERE L'APPARECCHIO DALL'UMIDITA`. ATTENZIONE ALTA TENSIONE 25kV, 1.0mA.
GCE 50
MINISTERO P.T. N.
(D.M. 25.6.1985/D.M. 27.8.1987) CUC 7303 25kV
MADE IN AUSTRIA FABRICANTE: GRUNDIG AG, WIEN
Chassis-Bezeichnung Bestellnummer ohne Farbkennzeichnung

Chassis designation Order number without colour code
This additional identification will be introduced for all current and newly
started up types of chassis.
The version number will also be printed on the supplementary documents
for these television receivers.
Please note that full particulars (type of TV, chassis and version number)
Serial No. 15/98

must be given when ordering spare parts in future.
Central
1/1
Service Information
Product Colour television receivers with chassis CUC 2030 (N) / 2031 (N) / 2040 (N) /
TV
2050 (N), e.g. ST 63-700 text, ST 63-780 text, ST 70-780 NIC/TOP, Melbourne
SE 7210 TOP
Possible complaint:
On replacement of the EEPROM IC82005 X24C04 the television receiver
does not accept all commands or no commands at all although the
emergency data set has been loaded.
Workshop:
When fitting a new EEPROM X24C04, the following options/settings are to
be carried out:
1. Loading the emergency data Press and hold down the „P-“
set button on the remote control
handset while switching the TV on
with the mains button.
2. Cancelling the Hotel mode Press and hold down the „i“ button
while switching on with the mains
button. Under the „Service“ menu,
set „Hotel“ to „OFF“.
3. Changing the background colour Move the bar to „OSD horizontal“

of the displayed menu (white/ in the Service Menu and press the
light-blue) buttons „AUX“, „OK“ in this order.
4. Cancelling the band limits Move the bar to „AGC“ in the

Service Menu and press the
buttons „AUX“, „OK“ in this order.
5. „Switch on with P1/AV“ Select „Switch on with P1“ in the
Serial No. 16/98

„Special functions“ menu.
6. AGC adjustment Carry out as described in the

Service Manual
7. AFC adjustment Carry out as described in the

Service Manual
Stores:
EEPROM X24C04 Part No. 8305 602 40500
Central
1/1
Service Information
New type of picture tube for 72cm colour television receivers with chassis Digi
TV
Basic+, Basic++, Digi 5 and Digi 6
The picture tubes A 68 ESF 002X43 (without coating) and A 68 ESF 202X43
(with coating) fitted into television receivers with above mentioned chassis
are no longer available. These picture tubes are not fully compatible with
the replacement tubes A 68 ESF 002X143 / A 68 ESF 202X143.
- changed yoke connections:

The figure below shows the connections of the deflection unit for the new
picture tubes A 68 ESF 002X143 part no. 8300 068 24300 and A 68 ESF
202X143 part no. 8300 068 20400.
L1 L2 L3 L4 F5 F6 F7
L1 - red yoke connecting lead (horizontal)

L2 - black yoke connecting lead (horizontal)
F5 - green yoke connecting lead (vertical)
F7 - white yoke connecting lead (vertical)
The different types of chassis require different changes:
Chassis Digi 5 CUC 1822, 1852
Serial No. 17/98

CRT fitted in the TV set Changes when fitting the replacement tube
A 68 ESF 002X43 A 68 ESF 002X143

A 68 ESF 202X43 A 68 ESF 202X143
An existing seagull correction board is to be
removed. The yoke connecting leads are
soldered directly to the deflection unit (see
figure).
A 68 ESF 002X043 A 68 002X143

A 68 ESF 202X043 A 68 202X143
No change. Connect the picture tube as
shown in the figure.
Central
1/2
-2-
Chassis Digi Basic + CUC 1826

A 68 ESF 002X043 A 68 ESF 002X143

A 68 ESF 202X043 A 68 ESF 202X143
No change. Connect the picture tube as shown
in the figure.
Chassis Digi Basic ++ CUC 1830

A 68 ESF 002X043 A 68 ESF 002X143

A 68 ESF 202X043 A 68 ESF 202X143
Connect the picture tube as shown in the figure.
+A voltage from 140V to 138V
C 53006 from 0.5µF to 0.41µF part no. 8515 722 24600
C 53071 from 13nF to 12.5nF part no. 8515 911 70200
L 53074 to 260µH part no. 0924 685 96200
CR 58011 from 1.8kOhm to 1.2 kOhm part no. 8706 100 27500
R 50007 from 1.6 Ohm to 1.5 Ohm part no. 8766 327 40500
R 50008 from 1.6 Ohm to 1.5 Ohm part no. 8766 327 40500
Chassis Digi 6 CUC 1842

A 68 ESF 202X043 A 68 ESF 202X143

Connect the picture tube as shown in the figure.
+A voltage from 145V to 143V
C 53071 from 10.5nF to 10nF part no. 8515 911 40900
L 53074 to 250µH part no. 0924 685 95300

Service Information
New type of picture tube for 72cm colour television receivers with chassis
TV
CUC 6365 / 6331
The picture tubes A 68 ESF 002X11, A 68 ESF 002X011 (without coating) and A
68 ESF 202X11, A 68 ESF 202X011 (with coating) fitted into television receivers
with above mentioned chassis are no longer available. These picture tubes are
not fully compatible with the replacement tubes A 68 ESF 002X111 / A 68 ESF
202X111.
- changed yoke connections:

The figure below shows the connections of the deflection unit for the new
picture tubes A 68 ESF 002X111 and A 68 ESF 202X111.
L1 L2 L3 L4 F5 F6 F7
L1 - red yoke connecting lead (horizontal)

L2 - black yoke connecting lead (horizontal)
F5 - green yoke connecting lead (vertical)
F7 - white yoke connecting lead (vertical)
The different types of chassis require additionally the following changes:
Serial No. 1/99
A 68 ESF 002X11 A 68 ESF 002X111
A 68 ESF 202X11 A 68 ESF 202X111
An existing seagull correction board is to be
removed. The yoke connecting leads are
soldered directly to the deflection unit (see
figure).
A 68 ESF 002X011 A 68 002X111

A 68 ESF 202X011 A 68 202X111
No change. Connect the picture tube as
shown in the figure.
Central
1
Service Information
Colour television receivers with Digi Basic++ chassis - CUC 1806, 1828, 1830, 1836,
TV
1929
e.g. ST 70-869 IDTV/LOG, M 70-281 IDTV/LOG, M 63-281 IDTV/LOG, ST 70-270 IDTV
Possible complaint:
Pronounced rattling noise.
Reason:
1. Magnetic radiation from the deflection yoke to the AF branch circuit.
2. The line interference suppression chokes may be in contact with the
metal screen causing vibrations.
Cure:
to point 1
Change the following resistors within the AF output stage:
Picture tube CR 40013 (0805) CR 40023 (1206) CR 40012/

CR40022(0805)
55cm (21“) PHI to 150 Ω to 180 Ω to 2.2 kΩ each
82cm (33“) PHI 16:9 PHI to 150 Ω to 180 Ω to 2.2 kΩ each
to point 2
Unsolder the metal screen and the line interference suppression choke and insert a
suppression choke with part no. 29500 834 9700. Since this choke is fitted with an
additional compensating coil, the metal screen is no longer necessary.
Stores:
Line interference suppression choke part no. 29500 834 9700
Serial No. 2/99
Central
1
Service Information
1. Colour television receivers ST 84-796/9 TOP/LOG, M 84-210/8 IDTV/LOG,
TV
M 84-210/8 A IDTV/LOG
The picture tubes A80 EFF 002X11 (ST 84-796/9 TOP/LOG) and A80 EFF 002X42
(M 84-210/8 IDTV/LOG, M 84-210/8 A IDTV/LOG) fitted to a.m. models are no longer
available. These tubes are mechanically not fully compatible with the replacement tubes
A80 EFF 272X11 / A80 EFF 272X43.
Due to the slightly larger overall dimension, the picture tube touches the fixing ribs within
the cabinet. Consequently, when changing the tube, these ribs must be cut by about 2mm
(see figure).
2 mm
Stores:
CRT A80 EFF 272X11 part no. 8300 0208 0500 (50Hz version)
CRT A80 EFF 272X43 part no. 8300 0208 0600 (100Hz version)
2. Satellite Retrofit Kit SER 150 ET for chassis CUC 1805, 1825, 1826, 1827 (Digi
Basic), 1806, 1828, 1829, 1830, 1836 (Digi Basic++), 1929, 1952, 1983, 1984, 1894 Serial No. 3/99
and 1842 (Digi 6)
From now on, the SER 150 ET Retrofit Kit will be delivered without the EPROMs previously
enclosed with the delivery for TV sets with Digi 6 and Digi Basic TV chassis.
The TV sets have already been provided with a software covering all the functions of the
SER 150 ET since 4/97. As a result, the EPROM of the currently delivered TV sets needs
not to be exchanged. Should you receive a TV set manufactured before 1997 for
retrofitting, check the software version (call up the version pressing the buttons „i“ -> „OK“ -
> „AUX“). If the version for the chassis:
CUC 1805, 1825, 1826 and 1827 (Digi Basic) is lower than 19798-300.20, and for the
chassis Digi 6 CUC 1842, 1894, 1984, 1952 and 1983 is lower than 19798-311.20, the
EPROM needs to be replaced. The EPROM of TV sets with Digi Basic++ needs not to be
replaced.
The required IC is available from the Central After-Sales Service under part number 19798
300 2400 (Digi Basic) or 19798 311 4700 (Digi 6).
Central
4121900000 (8002/8012) (8005/8015) After-Sales Service
1
Service Information
1. Colour television sets with chassis CUC 7303 and 45 cm Samsung or
TV
51 cm Samsung/Videocolor picture tubes - e.g. P 45-830 text, P 45-847
FR/text, T 51-720 text, T 51-731 text, T 51-071, T 51-732/4 text, T 51-732/5
text
Possible complaint:
No operation - failure of the switched mode power supply (transistor / drive-IC / other
components).
Cause:
Due to tolerances of the mains transformer 29201 513 9700 the collector current of
transistor T 665 (MJF 1800) may reach limit values and consequently cause the power
supply to fail.
Cure:
On replacement of the defective components change additionally the resistor R 666 from
0.82 Ohm to 0.91 Ohm. As a result limitation of the collector current is activated earlier so
that the limit values will not be exceeded.
Workshop:
Carry out this change when the power supply unit fails.
Stores:
Resistor 0.91 Ohm part no. 8765 0980 0000
2. Colour television sets with chassis 7303 - e.g. P 37-071, P 37-731 text,
P 45-731 text, T 51-720 text, T 51-732/5 text
Possible complaint:
Failure of vertical output IC TDA 3653.
Reason:
Static discharges to the deflection windings.
Cure:
Serial No. 4/99
1. For protecting the IC, change the capacitor C422 from 47nF to 0.1µF/100V.
Note: This 47nF capacitor is not inserted in all television receivers with 37cm
Philips picture tube. However the circuit board is prepared for later insertion of
this capacitor.
2. Solder an additional diode BAV 21 on to the foil side from the negative
terminal of the electrolytic capacitor C412 to pin 5 (cathode to pin 5) of the
vertical output IC TDA 3653.
Workshop:
Carry out this change when the vertical output stage failed.
Stores:
Diode BAV 21 part no. 8309 200 02100
Central
S1/4126900000 (8002/8012, 8005/8015) After-Sales Service
1/1
Service Information
Product: Colour television receivers with Digi Basic++ chassis, e.g. Sydney 100 SE
7020, Sydney 100 SE 7021, MW 82-50/8, M 70-290 IDTV Davio, M 84-211/8 IDTV
TV
Possible complaint:
Economy mains switch is not reliably released - release relay flutters.
Reason:
Relay current is too low to release the economy mains switch because of the lower
upper limit voltage (+Eco) of the new Standby mains stage 29304 050 8200.
Cure:
Change the resistor R81503 (either inserted in the keyboard control or the mains
switch board dependent on the type of TV set) from 22 kOhm to 15 kOhm.
Workshop:
Stores:
Resistor 15 kOhm, part no. 8700 011 30100.
Serial No. 5/99
Central
G1/4142900000 (8002/8012, 8005/8015) After-Sales Service
1/1
Service Information
Colour TV sets fitted with the chassis Digi Basic 3 - CUC 1930, 1931,
1832, e.g. Sydney SE 7230 Dolby, Xentia 72 M 72-400 Dolby, Arganto 82
TV
MW 82-510/8 DPL
Possible complaint:
A short time after switching on (about 20-30 sec.) the TV set cannot be
operated any more.
Cause:
Unfavourable constellation of the received station identifications.
Remedy:
Software change to version „18“ by replacing the EPROMS IC 80070.
Workshop:
On every incoming repair set with a software version below „18“ replace the
Eproms with one of the new version.
The software version of the TV set can be called up via the „Dialogcenter“
(button „i“ -> „OK“) by pressing the „AUX“ button. In doing this, the indication
29798-101.xx (the „xx“ positions indicate the software version) appears at the
top border of the picture screen.
If the software is updated from a version below „14“ to „18“, the following
points must be observed in addition:
1. After changing the software carry out an ATS reset. This is done by
switching on with the mains button with the L+ button held down (L+
button on the TV set!). Keep pressed the L+ button until the „ATS Rest“
window appears in the picture. When switching the TV set on the next
time, the set will prompt for entering the OSD language and the country.
Then it will start a new station search. Do not abort the station search!
2. Check and correct if necessary via the protected menu for the specialized
dealer (code „8500“) under menu item „Picture tube type“ the current
setting. The table below shows the setting depending on the picture tube:
Serial No. 1/00

Indication in the "Picture tube type" menu item Picture tube designation
P 72 A68ESF 202X143
T 72 A68LBT 696X99
T 72 RF A68LQP 356X97
P 70/16:9 W66ESF 202X44
P 82/16:9 W76ESF 231X44
T 82 RF/16:9 W76LPF 350X99
P 70 RF/16:9 W66ERF 031X044
P 82 RF/16:9 W76ERF 031X044
Stockkeeping:
Eprom IC 80070 part no. 29798 101 1800
Central
4103000000 (8002/8012, 8005/8015) After-Sales Service
1/1
Service Information
Colour TV sets Atlanta SE 7250 PIP/Dolby, Atlanta SE 7250/8 Dolby, and

Sydney SE 7230 Dolby with Toshiba A 68LBT696X99 picture tube.
TV
Possible complaints:
Unsharp picture, changing picture sharpness or buzzing noise from the
picture tube.
Cause:
Defect of the base focus control R 64006 on the dynamic focus board. In the
case of this defect, only a minimum reaction can be observed when aligning
with the control R 64006.
Remedy:
Replace the control R 64004.
Workshop:
Replace the control if necessary. In addition fix the new control with a clamp,
part number 29700 640 0100.
Stockkeeping:
Focus control 90/120 MOhm Part number 29303 552 1100.
Clamp for control Part number 29700 640 0100.
Serial No. 2/00
Central
41130S0400 (8002/8012, 8005/8015) After-Sales Service
1/1
Service Information
Colour sets with chassis Basic ++
TV
CUC 1806, 1828, 1829, 1929, and equivalent sets.
Colour sets with chassis Basic 3

CUC 1832, 1930, 1931, and equivalent sets.
Possible complaint:
The set shows a brief flashing before the Eco switch unlocks.
Cause:
Through the attraction of the Eco switch the stanby power supply unit is charged
too highly and causes a reset of the processor module. This reset in turn causes
briefly before the release of the Eco switch a temporary rise of the operating
voltages and thus a brief flashing of the picture tube (brief building up of the
high tension).
Remedy:
Replace the standby transformer with the 29201 619 9700 type.
Workshop:
Carry out the replacement if applicable.
Stockkeeping:
Standby transformer, material no.: 29201 619 9700.
Serial No. 3/00
Central
42390S1500 (8002/8012; 8005/8015) After-Sales Service
1/1
Service Information
Colour TV sets ST 70-789 NIC/Dolby and ST 70-898 NIC/Dolby - CUC

2032
TV
Possible complaint:
After fitting the satellite retrofit kit SER 251, no satellite reception is possible.
Cause:
Contrary to brochure statements, these TV sets have been manufactured
without retrofit option.
Remedy:
Through effecting the following changes, the retrofit option is achieved:
1. Remove the chip resistances CR 32131 and CR 32129.
2. Fit the following components:
Position Component
CT 32128 BC 848 B
CR 32128 4.7 kOhm
D 32128 1 N4148
Workshop:
If retrofitting is required, make the required changes.
The components are to be found in the circuit diagram of the Service Manual
CUC 2032 (Mat. No. 72010 024 8000) on the pages 3-27.
Sets which are already prepared for retrofitting at the factory are marked with
„VNX“.
Storekeeping:
BC 848 B Mat. No. 8301 004 84800
4.7 kOhm (0805) Mat. No. 8706 100 08900
1 N4148 Mat. No. 8309 215 04500
Serial No. 4/00
Central
41400S1700 (8002/8012, 8005/8015) After-Sales Service
1/1
Service Information
Colour TV sets with chassis Basic ++
TV
CUC 1806, 1828, 1829, 1929 and similar
Colour TV sets with chassis Basic 3
CUC 1832, 1930 und 1931 and similar
Possible complaints:
The eco switch does not release.
Cause:
Through the attraction of the eco switch the standby power supply undergoes
a too high load and causes a reset of the processor unit. This reset causes
just before the attraction of the eco switch a brief rise of the operating voltage
and may therefore prevent the release of the eco switch.
Remedy:
Replace the standby transformator with the version 29201 619 9700. In
addition, the complete standby power supply unit can be replaced with the
version 29304 050 8500 on the chassis Basic 3.
Workshop:
Carry out the replacement if necessary.
Stockkeeping:
Standby transformator, material No.: 29201 619 9700.
Standby power supply unit, material No.: 29304 050 8500.
Serial No. 5/00
Central
42460S1500 (8002/8012; 8005/8015) After-Sales Service
1/1
Service Information
Colour TV sets wit the chassis Digi Basic 3 - CUC 1832, 1930 and 1931
e.g.: Sydney SE 720 Dolby, Xentia M 72-400 Dolby, Denver SE 8250/8 PIP/
TV
Dolby
Possible complaint:
No picture, no sound.
Cause:
Failure of the power supply transistor T 60006 (IRF PC50 or 2SK2699).
Remedy:
In addition to replacing the power supply transistor change the SMD
capacitor CC 60014 from 3.3 nF to 10 nF. This results in a better softstart
function of the power supply.
Workshop:
In the event of a defective power supply transistor replace in addition the
capacitor.
Stockkeeping:
SMD capacitor 10 nF 0805 Part no. 867219817300
Transistor IRF PC 50/2SK2699 Part no. 830280505000
Serial no. 1/01
Returns
4116100000 (8002/8012, 8005/8015) analysis
1/1
Service Information
Gerät: Colour TV sets Digi 100
TV
Flash programming for the new Digi 100 generation
For the above stated series of sets, no completely programmed EPROM has
been used for the device software. The software is stored in a Flash-Eprom that
can be externally loaded. In this way it is possible to update the software with-
out opening the housing of the TV set.
To do this, the new software is downloaded into the TV set via the serial inter-
face of a PC and the programming socket located at the rear of the TV set using
a download programme and a RS232 converter (Flash-Programmer F-Prog 1).
Required equipment
Flash-Programmer F-Prog 1, part no. 759880740000
Required hardware (minimum)

- PC with processor 486/66 and operating system Windows Version 3.11 or
higher
- 8 MB free main memory
- Free fixed disk capacity of 20 MB
- Internet access or InfoTip-System
Calling up the current device software

The software can be called up from a protected area of the Grundig Internet
Homepage after entering your customer number and a password, or it can be
called up via the InfoTip-System (under „Service Tips“).
Example for calling up the software from the Internet:
- Start the Microsoft Internet Explorer or Netscape Navigator.

- Enter http://www.grundig.com and confirm.
- Click to Info + Products on the Grundig Home-Page.
- Position the mouse pointer to Service.
- Click to Reseller Support. Serial no. 02/01
Returns
420710000 (8002/8012, 8005/8015) analysis
1/1
Note: In the retailer support menu, you may applicate for access by entering
your customer number and your address.
- Click to spare parts: ordering and listings, service documents.
- Enter your custumer number and password.
- Click to login.
- Click to spare parts lists and service documents.
2/3
Service Information TV 02/01
- Select the desired software under software download.

- Copy the selected device software into the folder C:\GRUNDIG\Software of
your PC which has been created when installing the F-Prog 1-PC software.
The downloaded packed file (*.zip) then must be unpacked by an appropriate

unpacker for „ZIP“ files (appropriate unpackers can be found, for example,
under www.winzip.com).
ZIP files cannot directly be loaded into the TV set!
Additional hints/particularities for programming with the „F-PROG 1“:
- Before connecting the Flash Programmer, switch the TV set off with its
mains button then connect the programmer when the operating LED
has gone out!
- After starting programming, the operating LED first remains dark then
starts flashing as soon as the Flash memory is deleted.
3/3
Service Information
Setting hints and special functions (options) for the colour TV sets with
TV
the chassis Digi 100 (CUC 1807, 1837, 1838, 1839, 1934, 1935)
e.g.: Elegance 70 M 70-300 Dolby, Elegance 70 MW 70-150/8 Dolby,
Hamburg SE 8240 Dolby, M84-212/8 Dolby, Toronto SE 7216 Dolby
Below you find setting hints and explanations for various functions of the TV
sets with the chassis Digi 100.
1. Power-on behaviour of the set

In the „Special functions“ menu you can select under the „Power on“ menu
item between „automatic“ and „Programme position 1“ .
automatic: the set is switched on with the last power-on mode. For this, the
last recognized programme position and operating mode (standby or
normal operating mode) are stored.
Note: if the set has been switched off with the mains button in standby
mode, it goes again in standby mode after power on and must
definitely be switched on using the remote control.
Programme position 1: the set selects programme position 1 each time it is
switched on.
2. Settings in the „Programme table“ menu

In this menu, further presettings can be programmed in addition to the
channel setting for every programme position.
Note: direct channel entry is only possible in the programme table.
„P+“ reversion point: the reversion point is the limitation of the programme
positions for programme selection using the „P+“ button. This
reversion point is marked with an orange line in the programme table.
To shift the reversion point, it is necessary to shift the programme
position above or below this line according to the direction of shift.
1-/2-/3- digit programme position selection (3-digit only with a retrofitted
satellite module): for 1-digit programme position selection you must
Serial no. 3/01
place the reversion point in the programme table between the
programme positions 1 and 10. For 2-digit programme position
selection place the reversion point between the positions 10 and 100.
Forced settings (forced colour standard, forced mono, fixed assignment of a
multi-channel sound, RF time constant, AFC):
In the „Channel settings“ menu (menu guide: „i“ -> „Programme table“
-> „Edit“ -> „Change channel settings“) you can carry out various
forced settings.
Note: it is also possible to set a forced colour standard for the AV
programme positions in this menu.
Returns
4121100000 (8002/8012, 8005/8015) analysis
1/2
Service Information TV 03/01
3. Volume adjustment:
You can store a volume setting deviating from the basic volume separately for every
programme position in the „Sound“ menu (blue button) under the menu item „Volume
adjustment“. This adjustment is allowed by the software only if the basic volume is higher than
7 of the 64 steps of the control range.
4. Picture settings (brightness, contrast, colour, etc.):

The desired picture settings are carried out in the „Picture“ menu (red button). Changing the
contrast is only possible with the „manual“ presetting. The presettings „During the day“ and „In
the evening“ are stored with fixed contrast settings. To get a better overview, it is possible to
reduce the large menu scale after selecting the desired menu item by pressing the „OK“
button. In doing so, more menu content is visible and the setting, e.g. colour contrast, is highly
facilitated.
5. Sat radio (only with satellite retrofit kit SER 300A):

Via the menu guide „i“ -> „Infothek“ -> „Sat-Radio“, about 40 pre-stored sat radio stations can
be called up (dark picture screen, only the station name is visible). In this operating mode, the
programme table can be displayed after pressing the „i“ button in order to select/change the
sat radio stations.
6. Time and date:

Each time the set is powered on, the internal software clock is set when receiving a station
broadcasting Teletext.
If only stations without Teletext are received after power on, no clock time can be called up. In
this case, the clock and time can manually be set via „i“ -> „Installation“ -> „Time and date“.
7. AV settings:
The sets with the chassis Digi 100 provide the possibility of individually configuring all
available AV programme positions. The factory settings are:
AV 1 for the connection of a Megalogic video recorder,
AV 2 for the connection of a DVD player (via RGB),
AV 3 (if available) for the connection of a VHS video recorder (a switching voltage is
necessary at the Euro-AV socket Pin 8),
AV 4 for the connection of a VHS camera.
If you wish to change these presettings, you can individually configure all AV connections via
„i“ -> „Installation“ -> „Connections“ . In this menu, various units are preset which can be
activated if they are required. A connection diagram can be displayed by pressing the yellow
button.
In addition own unit profiles can be created via the menu item „Manual AV settings“. These
unit profiles are indicated with „manual“ in the connection diagram. Please note that settings in
the „Manual AV settings“ must correctly be effected in any case, and that preset units at AV 1,
AV 2 etc. are deactivated at the same time (see connection diagram). For example, an
incorrectly set time constant would result in a black/white picture with a VCR signal source.
2/2
Service Information
1. Chassis Digi 100 - Flash-Programmer FProg1,

2. Chassis CUC 21… - Service Documents
TV
1. Chassis Digi 100 - Flash-Programmer FProg1
Additional function through software change (version 1.1)
After replacing the Feature module, the unit-specific settings like colour
registration, noise reduction, picture sharpness, white balance, CRT type, PIP
position, picture geometry, and the customer-specific programme data must be
set up.
The extension of the FProg1 software now makes it possible to read out this data
and to write it into the new module.
This means a considerable decrease of expenditure of work.
For reading out and programming the operating software and the unit-specific data
you need the Flashprogrammer FProg1, part no. 759880740000. Please consult for
this also the Service Information ”General, serial no. 01/01“.
The Flash-Programmer comes with the software version 1.0. Please load the current
software, version 1.1, directly from the Internet (see Online Service brochure). This
is to be found under “Reseller Support“, “Software Download“ in the category
”Programming software“, Product group ”DIGI 100”. The updated description of
the FProg1, V1.1 software is to be found under Advice ”Operating instructions Flash-
Programmer F-Prog1“.
Serial no. 04/01
Stockkeeping: Flash-Programmer FProg1, part no. 759880740000.
Returns
E-BS-SA_2801 (8002/8012, 8005/8015) Subject to alteration analysis
1/2
2. Chassis CUC 21… - Service Documents
Service Manual 720100407000
Service Manual, 1st supplement 720100407100
Dear business partner,
despite multiple checks of the printing data we are not immune against
printing errors. For this reason please correct the above documents
according to the following information.
• Ser vice Manual 720100407000

The following alignment points replace the corresponding alignment
points in the Service Manual, page 2-1.
Alignment Preparations Alignment Process
2. Tuner AGC 100MHz oscilloscope: Channel A: Tuner contact 10 or 11. Adjust 300mVpp with button Ǹ or Ƿ.
Ground: Tuner
Colour video generator: Feed in a colour scale (with switched-
off sound carrier) via the aerial,
≥80dBµV.
Ǻ
Call up the dialog line "AGC" via " " (Dialog Center) –> Terminate the dialog line "End" "with mem" –> "OK".
Service –> "OK" –> Service Code "8500".
8. Screen grid Colour video generator: Feed in a black test pattern. Use the UG2 control (splitter transformer) to adjust at the
voltage UG2 Adjust the screen brightness so test point having the highest voltage potential a voltage of
that the test pattern just turns dark. 112.5V ± 2.5V for 14" picture tubes, and a voltage of 150V
High-resistance volt- ± 2.5V for 15"...21" picture tubes.
meter via 220KΩ: Test points R, G, B
(picture tube plate).
Determine the test point having the highest voltage.
The following oscillogram ´E

replaces the oscillogram 78 on page 3-26
(CRT plate) of the Service Manual.
´E
• Service Manual, 1st supplement 720100407100
The following hint replaces the corresponding hint on page 3.
Software version number

Press the "Ǻ" button to call up the "DIALOG CENTER" menu –> OK.
Press "AUX" to display the software version number.
2/2
Service Information
Colour TV sets with the chassis CUC 2103 and CUC 2121
TV
e.g.: P 37-4101 TOP Davio, T 55-4101 TOP Davio, T 55-4104 TOP Lemaxx
Listed below are the unit types on which the option of retrofitting a satellite
retrofit kit SER 2100 has been omitted. In the new GRUNDIG main
catalogue, this is not considered in the technical data. In order to distinguish
the retrofit option, the version marking at the rear panel has been changed
from „VNM“ (retrofitable) into „VNA“ (not retrofitable).
The following unit types are concerned::
CUC 2103 CUC 2121

Arcance 37 P 37-2101 MV Davio 55 ST 55-854/8 Dolby
Davio 37 P 37-4101 TOP Greenville SE 5592 MV/Dolby
Davio 37 P 37-4101 TOP/1 Leemaxx 55 ST 55-4105 MV/Dolby
Davio 37 P 37-4101 TOP/TR ST 55-839/8 Dolby
Davio 37 P 37-4101 GB ST 55-908/8 Dolby
P 45-4101 TOP ST 55-908/8 FR/Dolby
P 45-4101 MV/TOP Xentia 55 ST 55-405/8 Dolby
Arcance 51 T 51-2101 MV
Davio 51 T 51-3101 TOP The units
Davio 51 T 51-3101 TOP/1 ST 55-734 GB/Dolby and
Davio 51 T 51-3101 TOP/TR ST 55-934 GB/Dolby can be
Davio 51 T 51-3101 MV retrofitted with the„VNM“
Arcance 55 T 55-2101 MV and „VNA“ marking. With the
Davio 55 T 55-4101 GB „VNX“ marking the retrofit
Davio 55 T 55-4101 MV option is omitted.
Davio 55 T 55-4101 TOP
Davio 55 T 55-4101 TOP/1
Davio 55 T 55-4101 TOP/TR
Leemaxx 55 T 55-4104 TOP
S 55-806 TOP/TR
Workshop:
On a small number of the Davio 37 P 37-4101 TOP sets with the version Serial no. 5/01
identification „VNM“ (retrofitable), the processor has not been fitted with a
socket but has directly been soldered in. So that the processor board can be
fitted in the event of a SAT retrofitting, you must solder in an IC socket in
place of the soldered-in processor.
Stockkeeping:
IC socket, 56-pin Part no. 813090012900
Returns
4128100000 (8002/8012, 8005/8015) analysis
1/1
Service Information
Necessary settings after replacing the memory EEPROMs for colour TV
TV
sets with the chassis CUC 2103, 2105, 2121, and 2130
e.g.: P 37-4101 TOP Davio, T 55-4101 TOP Davio, T 55-4104 TOP Leemaxx,
ST 55-854/8 Dolby
Possible complaint:
After replacing the EEPROM CIC82501 (M24C08) the set is not fully operati-
ve despite of loading the emergency data set. Especially the teletext function
is restricted.
Workshop:
The following settings must be carried out after fitting a new EEPROM
M24C08.
1. Loading the configuration Switch the set on with the mains switch then
data for the teletext decoder. switch it off again when the picture appears on
the screen.
Note: the menu display is shifted to the left!
2. Loading the emergency Press and hold down the „P-“ button on the
data set. remote control while switching the set on with
the mains switch.
3. Setting the menu colours. Set the menu item „OEM“ in the Service menu
(access with the code „8500“) to „off“.
4. Geometry, white balance, Carry out these settings according to the

AFC, and AGC alignment. Service Manual.
5. Configuration of the In the „AV 1“ programme position you can Serial no. 7/01
Euro-AV socket „AV 1“ select between „VHS“ and „SVHS“ under the
„Video“ menu item in the „Special Functions“
menu.
Note: it is absolutely necessary to keep the order of the first two points to
gurantee the proper functioning of the teletext!
Stockkeeping:
SMD IC M24C08 Part no. 830596000800
Returns
4130100000 (8002/8012, 8005/8015) analysis
1/1
Service Information
Number: E/08/01; e_tv081e
TV
Burned battery socket or battery connecting cable
P 37-830/12 and P 37-840/12 SAT, and eqivalent units
Possible complaint:
Failure of the 12V power supply due to burned battery sockets or battery
connecting cables.
Cause :
Contact resistance between the battery socket and the plug of the battery
connecting cable.
Remedy:
To ensure the proper fitting accuracy, the battery socket must be replaced along
with the battery connecting cable with the new version.
Stockkeeping:
Battery connection set FFS (battery socket and battery connecting cable).
Part no. 759550410700
TQ42_4101 (Online, 8002, 8012, 8005, 8015)

Alterations reserved. 1
Service Information
Number: E/09/01; e_tv091e
TV
Damage to the bottom corners and edges of the TV sets
Lenaro MFW 84 - 6110 and MFW 92 - 6110
Possible complaint:
Damage to the bottom corners and edges on the front side.
Cause:
Due to the small bottom clearance of the front trim, the corners and edges of the
trim can be damaged when putting down the TV set in an inexpert way.
Remedy:
When transporting the TV set make absolutely sure to put it always down in
horizontal position and not to tilt it to the front to prevent the vulnerable corners
and edges from being dented.
TQ42_4301 (8002, 8012, 8005, 8015)

Subject to alterations. 1
Service Information
Number: O/01/01; o_tv011e
TV
TV sets with Digi 100 chassis
Possible complaint:
The TV set switches at times to standby and then after several seconds back to normal
operation.
Cause:
This failure may be caused by an uncontrolled oscillation of the CVBS input and a faulty
software library of the processor.
Remedy:
To eliminate this failure it is generally necessary to update the unit‘s software. For this
consult the table 1 (software assignment).
- Update the operating software of the TV set. The software required can be down-
loaded from the Internet.
For this consult also the Service Informationen ”General 01/01“ and ”TV 04/01“
(external).
In addition it is necessary to check and change if necessary the circuit of the

Feature module of older TV sets. TV sets and chassis which do not require a change of
the circuit are listed in the tables 2 and 3. The positions of the serial numbers of the TV
sets and chassis are described on page 4.
For the positions of the components concerned on the Feature module please see the
circuit diagram excerpt and the PCB illustrations on page 2.
- Remove the chip capacitor CC80209 (coordinates x71/y78) if provided.
- Connect CIC80000, Pin 117 with ground (e.g. chip capacitor CC80205 (coordinates
x71/y81), replace with a chip jumper, or solder in a wire bridge from Pin 117 to
ground).
MA Masse zu Pin 110 U RESET

SDA2
VIDEO2
SCL2
V1 MA
FBAS
MA M
TXT
+H/UP2
.
CR80212
CR80203
M
n.v.
n.v.
CC80208
n.v.
33p
33p
CC80206
CC80207
CC80211
0
100n
CC80201
n.v.
CC80210
82
n.v.
MA 47p Q80205 CR80211
X
10
12
14
16
2
4
6
8
CR80208
0,33u
10k
CC80205
CC80202
CC80209 6MHz ST-JTAG
X
CR80206
n.v.
11
13
15
1
3
5
7
9
100
117 121 120 108 109 2 4 M 3 1 95

CVBS2
CVBS1A
CVBS1B
XTAL1
XTAL2
TMS
TDO
TDI
TCK
P6.0
P6.1
97 P6.2
99 P6.4
98 P6.3 CIC80000
100 P6.5
0 = TV-on SDA6000
101 P6.6
MQFP128
E-BS-SA_3501 (Online)
Alterations reserved 1
Service Information
CC84046
CC84078
CR80241
CC84044
CR82031
CC80076 CR80076
INC270
CC82043
CC82031
CT80075
CBR80240
TV
CC84047
CC80249
CC80021
1
CIC82001
CIC80242 CT80090
CR80090
CT80095
CR80099
CR80089
1
CC82021 CT80085
CR82005
CC82005
CR80240 CR80256
Version of the PCB without CC80209
1
CC80072
CIC80230 CC80073 CC80074 CC80075

CR70098
CC80071
CC80131
CC80123
CC80122
CC80121
CR80117
CIC80240 CR80118 CIC80000
CR80119 CR80251
CC80254
CR80252
CC80163 CC80153 CC80143

CC80152 CC80142
CC80151 CC80133
CC80144 CC80132
CC80233
CNW80121 CR80250
1
CR80081
CR80253
CC80081
CR80136
CR80137 CNW80132 CR80254
CC80184
CR70244
CC80037
CR80127
CC
CR80037
CC80183
CR80033
CR80032
CR80128
70
CNW80181
CR80036
CR70152
08
CR80156 CNW80144 CC80182
4
CR80157 CNW80171 CC80181 CR70345
CR80082
CR80158 CNW80161 CC80174 CR70348
CR80009
CT80080
CC80161
CC80214
CC80162
CNW80191
CT80033 CC80173
1
CC80213 CR70347
CC80171
CT80110
CR80078
CR80077
CR80071
CC80172
CR80034 CR70346 1 CR70245
CR80073
CC80203
CC80031
CT80034
CC80114
CR80114
CR80199
CC80205
CT80108
CR80109
CIC70150
CC70428
CC
CC70418
CT80077 CR70154
CR80192
CR80193
70
CT70305
CT80009 CR80110 CC80202 CR70159
08
CR70418
3
CR70342 CR80004
CR80006
CR70428 CR80216
CR70161 CC70162
CT80008
CR80217
CR80204
CC80204
CT80004
CR70343
CR70207
CC
CC70313
CC70226
CR70344 CL70322
70
CT70425
CR70429 CR70224
08
CR70426 CR70313
2
CR70427
CR70422 CT70306 CT70155
CT70422
CR70424
CR70464 CR70421 CL70321 CR70455 CC70455 1

CC70464 1
CC
CR70423
70
CT70465
08
1
CR70461
CT70420
1
CIC70200
CC70316 CR70012
CC70461 CC70420
CC70302
CR70302
CR70476 CIC70300
CR70463
CR70316
CC70460 CIC70250
CR70477
CR70006
CIC70475
1 CR70410
CR70013
CT70011
CR70303
CR70420
CT80204
CR70430
CD70227
CR70227
CC70476
CC70306
CC70308
CC70303
CC70309
CT70470
CR70473
CNW80171
CC70010
CR70004
CC70200
CT70015
61
CC70180
1
CNW80191
CIC70180
CC80171
CC80203
CR80199
CC80205
CR80192
CC80202
29306-231.24/4BS(00)
CIC82031
CR80076
CC84044
CC84046
CR80241
CC84078
INC270
CC82031
CR80238
CT80075
.
CR82031
CC80249
CC80076
CC84047
CC82043 CC80021
1
CIC82041 CT80090
CIC82001
CT80095
CR80099
CR80089
1
CR80090
CC82021
CR80240
CR82005 CR80265
CT80085
CC82005 CL80256
CC84079
Version of the PCB with CC80209

CC80072 CC80073
1
CR70098
CC80074
CIC80230
CC80075
CC80163 CR80152 CC80142 CC80131
CC80162 CC80151 CC80133 CC80123
CL80110 CC80161 CC80144 CC80132 CC80122
CC80121
CR80117 CC80071
CIC80240 CR80118
CR80119 CR80251
CC80254
CIC80000 CR80252
CT80108 CC80153 CC80143
CC80233
CR80071 CNW80121 CR80250

CC
1
CC80081
CR80081
CR80037
CC80037
70 CR80136 CR80253
08 CR80137 CNW80132 CR80254
4 CR80127 CC80184
CR80036
CR80033
CR80032
CC80183
CR70152
CR80128 CNW80181
CR80156 CNW80144 CC80182
CR80082
CT80080 CR80157 CC80181 CR70345 CR70244

CR80158 CNW80171
CT80042
CL80109 CC80214
CNW80161 CC80174
CC80213
CR70348 CR70245
CNW80191
CR80203
CR80199
CC80205
CT80033 CT80110 CC80173

CR70347
CR80034
CC80171
1
CR80077
CR80078
CC80172
CR70346 1
CC80031
CT80034
CT80041 CR80114 CC70154

CT80310
CC CT80077 CT80308 CC80210 CIC70150
70 CR80009 CC80114 CC80202
CC80209
CT80009
CR80192
08
CR80193
CL80120 CL80119 CR70159

3
CT70305 CR70342 CR80216 CC80208
CR80004
CR80007
CR80217
CT80004
CT80008
CR80006 CR70161 CC70162

CR80204
CC80204
CR70343
CT70425
CC
CR70426
70 CL70321 CL70322 CR70207

CC70226
08 CR70312 CR70344
2 CR70429 CC70313 1 CR70224
CR70313 CT70155
CR70427
CC CR70422 1
CT70422
CR70464 CT70306 1
CR70424
70 CR70421
08 CC70464
1
CC70420
CT70465 CR70423
CR70461 CC70316 CR70012
CIC70200
CIC70300
CR70302
CIC70250
CT70420
CC70004 CC70461
CR70463 CR70316
CR70006 CC70460 CT70011
CR70410
CR70420
CR70013
CC70476
CR70430
CT80204
CC70309
1
CR70319
CIC70475
CC70306
CT70470
CC70308
CC70303
CR70473
CC70200
CT70015
CC70010
CR70004
CC70180
161
CNW80191
CR80203
CR80199
1
CC80205
CIC70180
CC80171
1
CR80114
CC80210
CC80202
CC80209
80216 CC80208
Stockkeeping:
Chip jumper (0 Ω) Part no. 759880114900
Feature module with
updated software Part no. 295042032100/2200/2300/2400/3100/3200/3300/4100/
4200/4300/4400/4600
2
Service Information
TV
Table 1: Software assignment
The table below shows the unit-specific assignment of the Feature modules and the part
number of the associated software, the positions marked with xxxx being variable and
indicating the version (e.g. 297981110800).
TV set Feature module Software

ARGANTO 70 MW 70-515 MV/DOLBY 295042032200 29798111xxxx
ARGANTO 82 MW 82-515 MV/DOLBY 295042032300 29798113xxxx
ATLANTA FLAT SE 7260 DOLBY 295042034300 29798117xxxx
BOSTON SE 7012 DOLBY 295042034200 29798115xxxx
DAVIO 70 ST 70-292 DOLBY 295042032200 29798111xxxx
DAVIO 70 ST 70-292/8 DOLBY 295042032200 29798111xxxx
DAVIO 70 ST 70-5210 DOLBY 295042032200 29798111xxxx
DAVIO 70 ST 70-5210/8 DOLBY 295042032200 29798111xxxx
ELEGANCE 63 ST 63-300 DOLBY 295042032200 29798111xxxx
ELEGANCE 63 ST 63-300/8 DOLBY 295042032200 29798111xxxx
ELEGANCE 70 M 70-300 DOLBY 295042032200 29798111xxxx
ELEGANCE 70 M 70-3110 DOLBY 295042032200 29798111xxxx
ELEGANCE 70 MW 70-150/8 DOLBY 295042032200 29798111xxxx
ELEGANCE 70 ST 70-300 DOLBY 295042032200 29798111xxxx
ELEGANCE 70 ST 70-300/8 DOLBY 295042032200 29798111xxxx
ELEGANCE 82 MFW 82-3110 MV/DOLBY 295042032100 29798113xxxx
ELEGANCE 82 MW 82-150/8 DOLBY 295042032200 29798111xxxx
HAMBURG SE 8240 DOLBY 295042034200 29798115xxxx
LEEMAXX 72 MF 72-9110/8 DOLBY 295042032100 29798113xxxx
M 70-879/8 DOLBY 295042032100 29798113xxxx
M 72-109 MV/DOLBY 295042032200 29798111xxxx
M 72-798 DOLBY 295042032200 29798111xxxx
M 84-212/8 DOLBY 295042032200 29798111xxxx
MW 82-3112 MV/DOLBY 295042032200 29798111xxxx
SEDANCE 70 M 70-284 DOLBY 295042032200 29798111xxxx
SEDANCE 70 ST 70-284 DOLBY 295042032200 29798111xxxx
SEDANCE 70 ST 70-284/8 DOLBY 295042032200 29798111xxxx
SEDANCE 72 M 72-2110 DOLBY 295042032200 29798111xxxx
SEDANCE 72 M 72-2110 MV/DOLBY 295042032200 29798111xxxx
ST 70-265/8 DOLBY 295042032200 29798111xxxx
ST 70-398 DOLBY 295042032200 29798111xxxx
SYDNEY SE 7240 DOLBY 295042034100 29798117xxxx
TORONTO SE 7216 DOLBY 295042034200 29798115xxxx
TORONTO SE 7216/8 DOLBY 295042034200 29798115xxxx
WIEN SE 6340 DOLBY 295042034200 29798115xxxx
XENTIA 55 M 55-420/8 DOLBY 295042032200 29798111xxxx
XENTIA 70 FLAT MFW 70-430/8 DOLBY 295042032100 29798113xxxx
XENTIA 72 FLAT MF 72-430 DOLBY 295042032300 29798113xxxx
XENTIA 72 FLAT MF 72-430/8 DOLBY 295042032300 29798113xxxx
XENTIA 72 M 72-420 DOLBY 295042032200 29798111xxxx
XENTIA 82 FLAT MFW 82-430/8 DOLBY 295042032900 29798121xxxx
3
Service Information
TV
TV sets not requiring a hardware change
For the TV sets listed below from the indicated serial number of the TV set (Made in Austria) or
of the chassis (Made in Germany) no hardware change is required.
The serial number of the TV set is to be found on the adhesive barcode label below the
barcode at the rear of the set. The serial number corresponds with the positions 12 to 17 of
the 18-digit paging code.
Example: XX XXXXX XXXX 111111 X.
The serial number of the chassis is to be found at the right chassis side after removing the rear
panel.
4
Service Information
Table 2: TV set production „Made in Austria“
TV
Order Chassis from unit
Unit type
number name serial number
Boston SE 7012 DOLBY GCI2375 CUC 1837 500001
Boston SE 7012 DOLBY GCI2324 CUC 1837 500001
ELEGANCE 70 M 70-300 DOLBY GCK9742 CUC 1837 510800
ELEGANCE 70 M 70-3110 DOLBY GCN6400 CUC 1837 500001
ELEGANCE 70 MW 70-150/8 DOLBY GCI9142 CUC 1934 500001
ELEGANCE 70 ST 70-300 DOLBY GCM8310 CUC 1837 502300
ELEGANCE 70 ST 70-300 DOLBY GCM8300 CUC 1837 507700
ELEGANCE 70 ST 70-300/8 DOLBY GCL0692 CUC 1837 500300
M 70-879/8 DOLBY GCM5100 CUC 1837 504700
M 72-109 MV/DOLBY GCM5300 CUC 1838 501700
M 72-798 DOLBY GCM5200 CUC 1838 501600
SEDANCE 70 ST 70-284 DOLBY GCK6500 CUC 1837 500700
SEDANCE 70 ST 70-284 DOLBY GCK6592 CUC 1837 507400
SEDANCE 70 ST 70-284/8 DOLBY GCK6675 CUC 1837 501300
SEDANCE 70 ST 70-284/8 DOLBY GCK6692 CUC 1837 503800
SEDANCE 72 M 72-2110 DOLBY GCM2700 CUC 1838 504130
SEDANCE 72 M 72-2110 MV/DOLBY GCM1900 CUC 1838 501000
ST 70-265/8 DOLBY GCM5400 CUC 1837 501450
ST 70-398 DOLBY GCM3300 CUC 1837 501500
Sydney SE 7240 DOLBY GCM5710 CUC 1838 500001
Sydney SE 7240 DOLBY GCM5700 CUC 1838 500001
Toronto SE 7216/8 DOLBY GCK6775 CUC 1838 500001
Wien SE 6340 DOLBY GCM5500 CUC 1837 504100
XENTIA 63 M 63-420/8 DOLBY GCI8300 CUC 1837 500001
XENTIA 63 M 63-420/8 DOLBY GCI8377 CUC 1837 504300
Table 3: TV set production „Made in Germany“
Chassis
Order Chassis from chassis
Unit type part number
number name serial number
29704011 . . . .
ARGANTO 70 MW 70-515 MV/DOLBY GCM5800 CUC 1934 3700 000001
ARGANTO 82 MW 82-515 MV/ DOLBY GCM5900 CUC 1935 3300 000051
Atlanta Flat SE 7260 DOLBY GCK6475 CUC 1838 2200 000001
Boston SE 7012 DOLBY GCI2375 CUC 1837 1600 007586
Boston SE 7012 DOLBY GCI2324 CUC 1837 1600 007586
DAVIO 70 ST 70-292 DOLBY GCI8572 CUC 1837 2500 010106
DAVIO 70 ST 70-292/8 DOLBY GCI8472 CUC 1837 0200 001556
DAVIO 70 ST 70-292/8 DOLBY GCI8452 CUC 1837 0200 001556
ELEGANCE 70 MW 70-150/8 DOLBY GCI9142 CUC 1934 1000 005291
ELEGANCE82Flat MFW 82-3110 MV/DOLBY GCL8540 CUC 1935 1900 004181
Hamburg SE 8240 DOLBY GCL7900 CUC 1935 2300 001556
M 84-212/8 DOLBY GCI9090 CUC 1839 1700 002451
MW 82-3112 MV/DOLBY GCM9800 CUC 1935 3600 000751
Sydney SE 7240 DOLBY GCM5710 CUC 1838 2600 005251
Sydney SE 7240 DOLBY GCM5700 CUC 1838 2600 005251
Toronto SE 7216 DOLBY GCK6875 CUC 1838 3900 007016
XENTIA 72 Flat MF 72-430 DOLBY GCL6777 CUC 1838 0400 / 2000 000021 / 000001
XENTIA 72 M 72-420 DOLBY GCL6977 CUC 1838 0600 009251
XENTIA 72 M 72-420/8 DOLBY GCL7077 CUC 1838 0700 001751
5
Service Information
TV
TP 750/715 and equivalent units
Possible complaint:
Missing hints to battery polarity in battery compartment.
Remedy:
Insert the batteries as shown in the figure below.
TQ42_4201 (Online))
Alterations reserved. 1
Service Information
TV
ST 70-2103 SAT retrofitting not possible
Cause:
Plug base ST-V3 missing on several chassis.
Remedy:
Retrofit the plug base ST-V3 (5-pin), part no. 293038700500.
Stockkeeping:
Plug base ST-V3 (5-pin), part no. 293038700500
TQ42_4501 (Online)
Subject to alterations. 1

Grundig Service Information

Uploaded by

Copyright:

Available Formats

Grundig Service Information

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Grundig Service Information

Uploaded by

Copyright:

Available Formats

SERVICE INFORMATION

Product: TV's with Digi Basic chassis Television No. 1/97

Product: TVR 3701 SV Television No. 2/97

Portable mono TV/VCR combination TVR 3701 SV

fit these components

Technical Services / Information

Product: CUC 7301 Television No. 3/97

Technical Services / Information 8002/8012 52097S0497

CBR67 CR3906 CC3903

CBR62 CBR66 CC3803

CR3960 CBR57 CBR41

CBR74 CBR42 CBR39

Product Mono TV Recorders TVR 3710, 5100 and 5500

Product Colour television receivers with Digi IV chassis - CUC 1821/1851/1881/1892

Serial No. 12/97

Product Correction of Service Information 9/97

Cure: Serial No 14/97

correct position position is too low

Product Colour television receivers ST 72-261 IDTV/LOG and ST 72-261/8 IDTV/LOG

Product Satellite Receivers STR 631/632/641 and 642

Serial No. 19/97

Product Colour television receivers MW 70-100/8, M 72-100 and M 72-100/8

Serial No. 20/97

Product Risks of failure of electric connections (solder pads) caused by ageing

In this connection we would like to refer you to our Service Information

Product Satellite Receivers - memory EEPROMs

Product Correction of Service Information bulletin 12/97

Serial No. 3/98

Serial No. 4/98

Serial No. 5/98

Serial No. 6/98

Product Colour television receivers with chassis Digi Basic/Basic+/Basic++

The television receivers with above mentioned chassis are partly

1. The traditional black socket terminal

Serial No. 8/98

Serial No. 9/98

Serial No. 10/98

Product Colour television receivers with chassis CUC 2030

Serial No. 11/98

In this connection we want to point out to the observance of the generally

Serial No. 12/98

SER 150 no EPROM included (no longer available)

Serial No. 13/98

Serial No. 14/98

Chassis-Bezeichnung Bestellnummer ohne Farbkennzeichnung

Serial No. 15/98

3. Changing the background colour Move the bar to „OSD horizontal“

4. Cancelling the band limits Move the bar to „AGC“ in the

5. „Switch on with P1/AV“ Select „Switch on with P1“ in the

Serial No. 16/98

6. AGC adjustment Carry out as described in the

7. AFC adjustment Carry out as described in the

- changed yoke connections:

L1 - red yoke connecting lead (horizontal)

The different types of chassis require different changes:

Chassis Digi 5 CUC 1822, 1852

Serial No. 17/98

A 68 ESF 002X43 A 68 ESF 002X143

A 68 ESF 002X043 A 68 002X143

Chassis Digi Basic + CUC 1826