Scribd
Upload
460 views5 pages

MML Nokia1

The document provides instructions for checking the status, alarms, parameters, software, and traffic of Nokia network equipment using diagnostic commands. It includes commands for checking the status of BCFs, ETs, TRXs, alarms, parameters, software versions, GPRS, traffic, and extracting data from the OSS system.

Uploaded by

bethor_
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
460 views5 pages

MML Nokia1

The document provides instructions for checking the status, alarms, parameters, software, and traffic of Nokia network equipment using diagnostic commands. It includes commands for checking the status of BCFs, ETs, TRXs, alarms, parameters, software versions, GPRS, traffic, and extracting data from the OSS system.

Uploaded by

bethor_
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 5

NOKIA I.

STATUS/ALARM (EX NO BCF=100;ET=50) LIHAT STATUS HISTORY BCCH MISSING (NR= 7767) LIHAT STATUS BCF/TRAFFIC LIHAT ALARM BCF AKTIF CHECCK SITE/TRAFFIC PER TIMESLOT LIHAT HISTORY ALARM BCF LIHAT STATUS H/W (ET,BCSU) LIHAT ALARM ET AKTIF LIHAT HISTORY ALARM ETprint ZEOH::BCF=100,NR=7767; ZEEI:BCF=100; ZEOL:100; ZERO : BCF = ; ZEOH:<YYYY-MM-DD>,:BCF=100:; ZUSI:ET; ZAHO:ET,50:; ZAHP:ET,50:;

CHECK STATUS N7

ZNEL; or ZNLI; ZNLC:1,INA:; ZNLC:1,ACT:; ZNLC:1,EXE:; ZUSU:TCSM,1;

Test N7

TEST TCSM CHECK Traffic ATR Lock ET LIHAT ISI DALAM 1 ET LIHAT JUMLAH CIRCUIT DLM 1 BSC (IDLE/BUSY) LIHAT JUMLAH CIRCUIT DLM 1 BSC (DETAIL) ZRCI:SEA=3:CGR=1:PRINT=5; ZUSC:ET,48:BL,; Yes/No ZDSB:::PCM=A; (A=NO.ET) ZCEL:CGR=1,; ZCEL:CGR=1:CONN=BU,FORM=EXT; ZCEL:CGR=1,FORM=EXT; zcec:etpcm=48,crct=1-1&&-31&2-1&&-31:bl; (ganti status ATR)

Check Status OM Signaling & TRX Signaling Change status D-Channel (WO/BL/AD) OM SignalLng & TRX Signaling CHECK CRC PERFORMANCE CHECK OPC (Sebagai SPC di MSC )

ZDTI : NAME : OMxxx/Txxx ; ZDTC : OMxxx/Txxx1 ;

ZYMO:ET,50:CRC:; ZNHI:;

II. LOCKED/UN-LOCKED (EX NO BCF=100 & BTS=200,ET=5) LOCKED/UNLOCKED BCF ZEFS:100:L:; / ZEFS:100:U:;

LOCKED/UNLOCKED BTS

ZEQS:BTS=100:L:; / ZEQS:BTS=100:U:;

LOCKED/UNLOCKED TRX

ZERS:BTS=200,TRX=001,:L:; / ZERS:BTS=200,TRX=001,:U:; Zefr ZERO: ZUSC:ET,250 ZUSC:ET,50:TE:; TERUS ZUSC:ET,50:WO:;

reset bcf Cek Kelurusan TSlot utk TRX TEST ET ET MULAI 32 ET: 32,40,48 KELIPATAN 8 UTK ARAH KE MSC ET: 33 BUAT GPRS SELAIN ITU UNTUK BTS Test TRXSig

ZDTI:::PCM=123;(lih nama TRXSIG) ZDTC:T1234:bl; ZDTC:T1234:wo;

List Output External Input And Output Texts for Alarms Create New text RESET BCF (OMU/SITE) DIAGNOSIS ET CANCEL ET ALARM

ZEFP; ZEFE:TID=10:TEXT="SMOKE ALARM"; ZEFR:A(no.BCF); ZEFR:( No.BCF):OMU:; ZUDU:ET,<#>; YMO:ET,160::;

ZACA:<alarm_no>;

III.PARAMETER CHECK POWER SETTING HANDOVER PARAMETER CHECK BTS IDENTIFICATION PARAMETER CHECK BCF IDENTIFICATION PARAMETER CHECK FREQUENCY HOPPING PARAMETER CHECK EXTERNAL BCF INPUTS & OUTPUTS GANTI HOPPING MODE MODIFY TRANSCEIVER & TSL CHECK TRAFFIC DI BSC IV.SOFTWARE ZEUO:BTS=<#>; ZEHO:BTS=<#>; ZEAO:BTS=4; ZEQO:BTS=<#>; ZEFO:<BCF_NO>:IDE; ZEFO:<BCF_NO>:HOP; ZEFO:<BCF_NO>:IOP; ZEQE:BTS=XXX:HOP=n/rf; ZERM ZEEL;

CHECKS BUILD ATTACH SW Check Software DI LEVEL BCF

ZEWL; (all BTSs in BSC) ZEWA ZEWO : BCF = ;

Cek GPRS ZERO Cek NSEI GPRS ZFWO:BCSU0&&6:BTS:; Cek Alarm Normally open/close ZEFO: NO.BCF: ALL:; Lihat parameter power max ZEUO:BTS=16; Memaksimalkan pmax ZEUG:BTS=16:PMAX=0; Pindahin BCCH ZDTC:T051X:AD;

X =Nomor TRX 51=Nomor BCF

Cek Traffic di ATER ZCEL:CGR=1,FORM=EXT:; Change status ext. alarm Zefx:<bcf no>:inbr=:rou=act,:sev=al3,tid=,:; Cek alarm di BTS ZEFO: no,bcf :iop; ZERS pindah bcsu1 ke spare ZUSC:BCSU,1:SP:; Create nambah adjacent/hoping beda bsc ZEAC:BTS=6::LAC=5632,CI=25322,NCC=5,BCC=1,FREQ=36:; Create nambah adjacent/hoping ZEAC:BTS=6::ABTS=8:FREQ=36:; ZUSU:OMU;Y-------------------------RESET OMU Melihat message index ZECP; Menghidupkan cell broad cast ZECS:message index:bts= 91&&93:; Melihat load cell broad cast ZECL:; Melihat A-Bis allocation: ZDSB:::pcm= ZOLT; untuk melihat traffic BSC Diagnostic unit

ZUSC:ET,xx:TE,; ZUDU:ET,xx :; ZUDH:ET,xx:; ZUSC:ET,xx:WO,; Melihat BCF ID dari ET : ZDSB:::PCM=(no); Check patcing di level BSC Avs 12,02 Msk tcsm, zddt,tcsm Ddt:tcsm,41 BLOK HOPPING BTS ZEQS:BTS=... :L:; ZEQE:BTS=..., HOP=N,; Circuit Zecc..etpcm..crct..1-1&&-31.. Cek TRX Priority (TRP) 2 = bukan pada bcch 1= pada bcch Zeqo:BTS=:MIS; Cek trafic 1 bsc = ZECL:CGR=1,CONN=ID&BU; Reset GPRS/Sector ZEQV:BTS=..GENA=N,:; ZEQV:BTS=..GENA=Y,:; Cek Orang Yg sedang akses di site: ZQNS Cek Orang Yg Lock/Unlock site Yg masi belum on servie: ZIGO: Y/M/D/,: USERID=ALL:CMD=EFS.:; Cara ngambil data oss

Step 1: Pada window yang datanya mau diambil klik FILE > PRINT-> Range All/Selected ->SETUP -> FILE -> tulis nama file yang mau kita bikin, dari contoh nama filenya di tulis TES -> OK -> OK Step 2: Buka cmd prompt, ketik ftp 10.200.82.3 NB: JABAR : IP 10.200.80.3 JATENG : IP 10.200.81.3 JATIM : IP 10.200.82.3 Sumatra : 10.200.84.3 Kalimantan 10.200.85.3 Masukkan user dan password login oss masing2 area Jika berhasil, ketik get TES NB: TES merupakan nama file yang kita buat sebelumnya Perhatikan lokasi direktori, yaitu : C:\Documents and Settings\Admin>

Setelah berhasil maka file sudah tersimpan pada direktori tersebut dengan nama file TES, logout dengan mengetik bye

Step3: -

Buka folder direktori C:\Documents and Settings\Admin>, lalu cari file TES kemudian buka dengan WordPad.

Selesai

You might also like