CS601-Data Communication Latest Solved MCQs from Final term Papers

Lectures 23-45

May 26,2011
Latest Mcqs

Mc100401285

[email protected]

Moaaz Siddiq

FINAL TERM EXAMINATION Spring 2011

Question No: 1 ( Marks: 1 ) - Please choose The inversion of the level at 1 bit is called as __________ NRZ-L NRZ-I Page 73 RZ Question No: 2 ( Marks: 1 ) - Please choose In selective-reject ARQ, only the specific damaged or lost frame is_____________. Retransmitted (Page 200) Forwarded Selected Rejected Question No: 3 ( Marks: 1 ) - Please choose YMODEM has _________Byte of data unit. 1024 Page 205 256 128 512 Question No: 4 ( Marks: 1 ) - Please choose Which of the following sublyer, resolves the contention for the shared media MAC (Page 219) LLC Physical Question No: 5 ( Marks: 1 ) - Please choose Like 10 Base 5, 10 Base 2 is a _________ topology LAN Ring Mesh Star Bus (Page 227)

Question No: 6 ( Marks: 1 ) - Please choose At the CRC generator, __________ added to the data unit after the division process 0s are (Page 176) 1s are The polynomial The CRC remainder is Question No: 7 ( Marks: 1 ) - Please choose Flow control is needed to prevent ___________. Bit errors Overflow of the sender buffer Overflow of the receiver buffer (Page 46) Collision between sender and receiver Question No: 8 ( Marks: 1 ) - Please choose In Y-MODEM Multiple files can be sent simultaneously True (Page 205) False Question No: 9 ( Marks: 1 ) - Please choose In 56K Modems Max Uploading speed is ______ bytes and downloading speed is ______ byte. 40K, 56K 33.6K, 56K (Page 117) 56K, 33.6K None of given Question No: 10 ( Marks: 1 ) - Please choose If db is amplified then attenuation is -----------------Positive (Page 142) Negative Zero None of the above Question No: 11 ( Marks: 1 ) - Please choose Amplifiers are used to __________the signal to heat. Amplify (Page 142) Rectify Testify Nullify Question No: 12 ( Marks: 1 ) - Please choose _________requires the maximum number of I/O ports. Bus Star Mesh (Page 29)

Ring Question No: 13 ( Marks: 1 ) - Please choose There are ________ basic categories of multiplexing. 3 (Page 148) 4 2 5 Question No: 14 ( Marks: 1 ) - Please choose In _____________ transmission, bits are transmitted over a single wire, one at a time. Asynchronous serial Synchronous serial Parallel (Page 98) Asynchronous & Synchronous serial Question No: 15 ( Marks: 1 ) - Please choose In_____________ transmission, bits are transmitted over their own wires Asynchronous serial Synchronous serial Parallel http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter4/mixed_quiz.html Asynchronous & Synchronous serial Question No: 16 ( Marks: 1 ) - Please choose EIA 232 allows for a maximum bit rate of __________Kbps. 40 30 20 (Page 104) 10 Question No: 17 ( Marks: 1 ) - Please choose In CRC the quotient at the sender _____________ Becomes the dividend at the receiver Becomes the divisor at the receiver Is discarded http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Is the remainder Question No: 18 ( Marks: 1 ) - Please choose In line discipline after the data transmission, the sending system finishes with an _____________ frame EOT (Page 189) EKT ENT ESP

FINALTERM EXAMINATION Spring 2010

Question No: 1 ( Marks: 1 ) - Please choose one Encryption and encoding are the same terms. True False (Page 52) Question No: 2 ( Marks: 1 ) - Please choose one Traditional modems are wide spread now to a data rate of __________. 56 Kbps (Page 115) 72 Kbps 42 Kbps 96 Kbps Question No: 3 ( Marks: 1 ) - Please choose one Bi phase encoding is a type of bipolar encoding in which we use two voltage levels. True False (Page 73) Question No: 4 ( Marks: 1 ) - Please choose one The _______________ layer changes bits into electromagnetic signals. physical http://www.ee.surrey.ac.uk/Projects/CAL/networks/Physical_Layer.htm data link transport none of given Question No: 5 ( Marks: 1 ) - Please choose one Which is not an element of protocol? Semantics Timing Communication service module (Page 19)

Question No: 6 ( Marks: 1 ) - Please choose one A telephone network is an example of a __________ network. Packet-switched Circuit-switched (Page 38)

 Message-switched none of the given Question No: 7 ( Marks: 1 ) - Please choose one The bit rate always equals the baud rate in which type of signal? FSK (Page 86) QAM 4-PSK PSK Question No: 8 ( Marks: 1 ) - Please choose one Secondary hub in a tree must be a passive hub. True False (Page 31) Question No: 9 ( Marks: 1 ) - Please choose one In case of uploading at the switching station, data is converted to digital signal using ___________. TCP PCM (Page 116) ICP TDM Question No: 10 ( Marks: 1 ) - Please choose one Category 5 UTP cable is used for data transmission of upto__________. 100 Mbps (Page 123) 200 Mbps 250 Mbps 400 Mbps Question No: 11 ( Marks: 1 ) - Please choose one Which of the following primarily uses guided media? Cellular telephone system Local telephone system (Page 120) Satellite communications Radio broadcasting Question No: 12 ( Marks: 1 ) - Please choose one Ultra high-frequency waves always use __________ propagation. Ground Sky

 Line of Sight (Page 136) Space Question No: 13 ( Marks: 1 ) - Please choose one Distortion occurs in a ___________ signal. Rectified Composite (Page 141) Amplified none of the given Question No: 14 ( Marks: 1 ) - Please choose one Which of the following are not used to measure the performance of TX Media. Throughput Propagation Speed Propagation Time none of the given (Page 144) Question No: 15 ( Marks: 1 ) - Please choose one A portion of the path that carries TX b/w a given pair of devices is known as __________. Node Bridge Channel (Page 147) Gateway Question No: 16 ( Marks: 1 ) - Please choose one _________ takes data from one high speed line and breaks it into portions. Multiplexing Inverse multiplexing (Page 158) Inverse subtraction Inverse addition Question No: 17 ( Marks: 1 ) - Please choose one The _________ layer is the layer closest to the transmission medium. physical data link network transport http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter2/multiple_choice_quiz.html

Question No: 18 ( Marks: 1 ) - Please choose one In primary-secondary communication ______________ is always the initiator of a session Primary (Page 189) Secondary Sender Receiver Question No: 19 ( Marks: 1 ) - Please choose one YMODEM has _________Byte of data unit. 1024 (Page 205) 256 128 512 Question No: 20 ( Marks: 1 ) - Please choose one ____________ coordinates the amount of data that can be sent before receiving acknowledgment flow control (Page 186) error control data control Question No: 21 ( Marks: 1 ) - Please choose one If the ASCII character H is sent and the character I is received, what type of error is this? Single-bit (Page 169) Multiple-bit Burst Recoverable Question No: 22 ( Marks: 1 ) - Please choose one In __________ ARQ, if a NAK is received, only the specific damaged or lost frame is retransmitted. Stop-and-wait Go-Back-N Selective reject (Page 200) Stop-and-wait & Go-back-N Question No: 23 ( Marks: 1 ) - Please choose one Data link protocols can be divided into ______________ sub-groups. two (Page 202) three four five

Question No: 24 ( Marks: 1 ) - Please choose one If odd parity is used for ASCII error detection, the number of 0s per 8-bit symbol is _________ Even Odd (Page 173) Indeterminate 42 Question No: 25 ( Marks: 1 ) - Please choose one In Y-MODEM Multiple files can be sent simultaneously True (Page 205) False Question No: 26 ( Marks: 1 ) - Please choose one The PDU has no flag fields, no CRC, and no station address TRUE (Page 220) FALSE Question No: 27 ( Marks: 1 ) - Please choose one Check sum method is used for _______________ layers. Physical Application Transport Data link

http://www.cse.iitk.ac.in/users/dheeraj/cs425/lec09.html

Question No: 28 ( Marks: 1 ) - Please choose one Repeater is an amplifier, not a regenerator. True False (Page 240) Question No: 29 ( Marks: 1 ) - Please choose one RARP stands for Reverse Address Resolution Protocol. True (Page 244) False Question No: 30 ( Marks: 1 ) - Please choose one The BNC-T connector is a T-shaped device with _______ ports Three (Page 228) Two Four Five

FINALTERM EXAMINATION Spring 2010 Question No: 1 ( Marks: 1 ) - Please choose one When data are transmitted from device A to device B, the header from As layer 4 is read by Bs __________ layer. physical transport application none of the given http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter2/multiple_choice_quiz.html Question No: 2 ( Marks: 1 ) - Please choose one A periodic signal completes one cycle in 0.001 s. What is the frequency? 1 Hz 100 Hz 1 KHz (Page 61) 1 MHz Question No: 3 ( Marks: 1 ) - Please choose one Zero crossing bandwidth is also called as equivalent noise bandwidth. True False (Page 67) Question No: 4 ( Marks: 1 ) - Please choose one Amplitude in ASK is more resistive to EMI and Noise. True False (Page 87) Question No: 5 ( Marks: 1 ) - Please choose one If FCC regulations are followed, the carrier frequencies of adjacent AM radio stations are ____________ apart. 5 KHz 10 KHz (Page 95) 200 KHz 530 KHz Question No: 6 ( Marks: 1 ) - Please choose one There are _________________ types of serial transmission:

1 2 (Page 99) 3 4 Question No: 7 ( Marks: 1 ) - Please choose one Synchronous transmission has _____________. a start bit a stop bit gaps between bytes none of the given (page 99) Question No: 8 ( Marks: 1 ) - Please choose one Which of the following is an example of ITU-T modem standards? T-series X-series N-series V-series (Page 114) Question No: 9 ( Marks: 1 ) - Please choose one The maximum data rate in the uploading direction is still ____________. 26.6 Kbps 33.6 Kbps (Page 117) 36.6 Kbps 46.6 Kbps Question No: 10 ( Marks: 1 ) - Please choose one Category 5 UTP cable is used for data transmission of upto__________. 100 Mbps (Page 123) 200 Mbps 250 Mbps 400 Mbps Question No: 11 ( Marks: 1 ) - Please choose one All of popular Fiber optic connectors are ___________ shaped. Conical Barrel (Page 131) Circular Rectangular

Question No: 12 ( Marks: 1 ) - Please choose one The VLF and LF bands use _________ propagation for communications. Ground Sky Line of sight (Page 134) Space Question No: 13 ( Marks: 1 ) - Please choose one Multiplexing is the set of techniques that allows simultaneous TX of multiple signals across ___________ data link Single (Page 147) Multi Single and Multi none of the given Question No: 14 ( Marks: 1 ) - Please choose one Need for Addressing makes Asynchronous TDM inefficient for bit or byte ___________. Interleaving (Page 158) Addition Subtraction None of the given Question No: 15 ( Marks: 1 ) - Please choose one _________ takes data from one high speed line and breaks it into portions. Multiplexing Inverse multiplexing (Page 158) Inverse subtraction Inverse addition Question No: 16 ( Marks: 1 ) - Please choose one A traditional telephone line has a bandwidth of __________. 3000Hz (Page 111) 4000 Hz 2000 MHz 4000 MHz Question No: 17 ( Marks: 1 ) Please choose one If the ASCII character H is sent and the character I is received, what type of error is this? Single-bit (Page 169) Multiple-bit

 Burst Recoverable Question No: 18 ( Marks: 1 ) - Please choose one At the CRC generator, __________ added to the data unit after the division process 0s are 1s are The polynomial The CRC remainder is http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 19 ( Marks: 1 ) - Please choose one Error control in the data link layer is based on ________________ automatic repeat request (Page 196) automatic repeat acknowledgment automatic send acknowledgment Question No: 20 ( Marks: 1 ) - Please choose one In line discipline the initiator first transmits a frame called an ________ Enquiry (Page 189) Acknowledgment NAK Request Question No: 21 ( Marks: 1 ) - Please choose one Primary device uses ____________ to receive transmission from the secondary devices. ACK ENQ POLL (Page 191) Question No: 22 ( Marks: 1 ) - Please choose one Flow control is needed to prevent ___________. Bit errors Overflow of the sender buffer Overflow of the receiver buffer (Page 46) Collision between sender and receiver Question No: 23 ( Marks: 1 ) - Please choose one For stop-and-wait ARQ, for N data packets sent, ___________ acknowledgments are needed. N

 2N N-1 N+1 http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter11/mixed_quiz.html Question No: 24 ( Marks: 1 ) - Please choose one In Y-MODEM Multiple files can be sent simultaneously True (Page 205) False Question No: 25 ( Marks: 1 ) - Please choose one HDLC is an acronym for ______________. High-duplex line communication High-level data link control (Page 210) Half-duplex digital link combination Host double-level circuit Question No: 26 ( Marks: 1 ) - Please choose one Token Bus has no commercial application in data communications True (Page 232) False Question No: 27 ( Marks: 1 ) - Please choose one The BNC-T connector is a T-shaped device with _______ ports Three (Page 228) Two Four Five Question No: 28 ( Marks: 1 ) - Please choose one Each station in the Token Ring regenerates the frame. True (Page 234) False Question No: 29 ( Marks: 1 ) - Please choose one Repeater works on __________ layer. Data Link Physical Network (224) Application

Question No: 30 ( Marks: 1 ) - Please choose one Trunks are transmission media such as _________ that handle the telephone to the nearest end office. Satellite links Twisted-pair & Fiber-optic Twisted-pair Fiber-optic http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter8/mixed_quiz.html

Spring 2010 CS601- Data Communication Question No: 1 ( Marks: 1 ) - Please choose one __________representation of links that connect nodes is called as physical topology. geometrical logical physical (page 44) Question No: 2 ( Marks: 1 ) Please choose one The internet model consists of _________ layers. three two five seven http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter2/multiple_choice_quiz.html Question No: 3 ( Marks: 1 ) Please choose one Encryption and encoding are the same terms. True False (Page 52) Question No: 4 ( Marks: 1 ) - Please choose one The amplitude of a digital signal depends upon the________ to represent a bit. phase voltage (Page 59) wavelength Question No: 5 ( Marks: 1 ) - Please choose one The inversion of the level at 1 bit is called as __________ NRZ-L

 NRZ-I (Page 73) RZ Question No: 6 ( Marks: 1 ) - Please choose one Modulation of an analog signal can be accomplished through changing the ___________ of the carrier signal. amplitude frequency phase all of the given Question No: 7 ( Marks: 1 ) - Please choose one If FCC regulations are followed, the carrier frequencies of adjacent AM radio stations are ____________ apart. 5 KHz 10 KHz (Page 95) 200 KHz 530 KHz Question No: 8 ( Marks: 1 ) - Please choose one Category 5 UTP cable is used for data transmission of upto__________. 100 Mbps (Page 123) 200 Mbps 250 Mbps 400 Mbps Question No: 9 ( Marks: 1 ) - Please choose one The RG number gives us information about ________. Twisted pairs Coaxial cables (Page 125) Optical fibers all of the given Question No: 10 ( Marks: 1 ) - Please choose one The inner core of an optical fiber is __________ in composition. Glass plastic (Page 130) Copper Bimetallic Liquid

Question No: 11 ( Marks: 1 ) - Please choose one All of popular Fiber optic connectors are ___________ shaped. Conical Barrel (Page 131) Circular Rectangular Question No: 12 ( Marks: 1 ) - Please choose one The VLF and LF bands use _________ propagation for communications. Ground Sky Line of sight (Page 134) Space Question No: 13 ( Marks: 1 ) - Please choose one Multiplexing is the set of techniques that allows simultaneous TX of multiple signals across ___________ data link Single (Page 147) Multi Single and Multi none of the given Question No: 14 ( Marks: 1 ) - Please choose one A portion of the path that carries TX b/w a given pair of devices is known as __________. Node Bridge Channel (Page 147) Gateway Question No: 15 ( Marks: 1 ) - Please choose one Which error detection method involves polynomials? Checksum Two-dimensional parity check CRC (Page 177) Simple parity check Question No: 16 ( Marks: 1 ) - Please choose one If the ASCII character G is sent and the character D is received, what type of error is this? Single-bit Multiple-bit

 Burst Recoverable http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 17 ( Marks: 1 ) - Please choose one Which error detection method involves the use of parity bits? Simple parity check & two dimensional parity check CRC Two-dimensional parity check Simple parity check http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 18 ( Marks: 1 ) - Please choose one Which error detection method can detect a single-bit error? Simple parity check Two-dimensional parity check CRC All of the given http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 19 ( Marks: 1 ) - Please choose one The Hamming code is a method of __________ Error detection Error correction (Page 181) Error encapsulation Error detection & Error encapsulation Question No: 20 ( Marks: 1 ) - Please choose one Sliding window requires that data frames be transmitted _______________ Sequentially (Page 199) Frequently Synchronously Asynchronously Question No: 21 ( Marks: 1 ) - Please choose one In selective-reject ARQ, only the specific damaged or lost frame is_____________. Retransmitted (Page 200) Forwarded Selected Rejected

Question No: 22 ( Marks: 1 ) - Please choose one Which of the following sub layer, resolves the contention for the shared media MAC (Page 219) LLC Physical Question No: 23 ( Marks: 1 ) - Please choose one The PDU has no flag fields, no CRC, and no station address TRUE (Page 220) FALSE Question No: 24 ( Marks: 1 ) - Please choose one IEEE divides the base band category into ______ standards. 5 (Page 222) 4 3 6 Question No: 25 ( Marks: 1 ) - Please choose one Like 10 Base 5, 10 Base 2 is a _________ topology LAN Ring Mesh Star Bus (Page 227) Question No: 26 ( Marks: 1 ) - Please choose one Check sum method is used for _______________ layers. Physical Application Transport Data link

http://www.cse.iitk.ac.in/users/dheeraj/cs425/lec09.html

Question No: 27 ( Marks: 1 ) - Please choose one Repeater works on __________ layer. Data Link Physical Network (Page 224) Application

Question No: 28 ( Marks: 1 ) - Please choose one Trunks are transmission media such as _________ that handle the telephone to the nearest end office. Satellite links Twisted-pair & Fiber-optic Twisted-pair Fiber-optic http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter8/mixed_quiz.html Question No: 29 ( Marks: 1 ) - Please choose one Which of the following ___________ uses a series of filters to decompose multiplexed signal into its constituent signals? MUX DEMUX Switch Bridge

(Page 150)

Question No: 30 ( Marks: 1 ) - Please choose one In Fast Ethernet, data rate can be increased by _______________ collisions. Increasing Decreasing (Page 230) Keeping Constant None of the given

FINALTERM EXAMINATION Spring 2009

Question No: 1 ( Marks: 1 ) - Please choose one Which is not an element of protocol semantics timing communication service module (Page 19) Question No: 2 ( Marks: 1 ) - Please choose one Layers 5, 6 and 7 also called as network support layers. True False (Page 42) Question No: 3 ( Marks: 1 ) - Please choose one Fourier transform tells us that any digital signal can be decomposed into infinite number of periodic signals True False

(Page 42)

Question No: 4 ( Marks: 1 ) - Please choose one Time domain plot show changes in signal phase with respect to time. True False

(Page 63)

Question No: 5 ( Marks: 1 ) - Please choose one Analog to digital conversion is also termed as modulating an analog signal. True False

(Page 70)

Question No: 6 ( Marks: 1 ) - Please choose one DC component is also termed as Direct current component or a component with non-zero frequency. False True

(Page 72)

Question No: 7 ( Marks: 1 ) - Please choose one Manchester is a type of ____________encoding. biphase (Page 75) polar biphase & polar none of the given Question No: 8 ( Marks: 1 ) - Please choose one The inversion of the level at 1 bit is called as __________ NRZ-L NRZ-I RZ

(Page 73)

Question No: 9 ( Marks: 1 ) - Please choose one PCM is the first process of PAM. True False

(Page 80)

Question No: 10 ( Marks: 1 ) - Please choose one In 4PSK each phase change represents ______bits. 3 6 2 4

(Page 91)

Question No: 11 ( Marks: 1 ) - Please choose one In RS 422 Balanced mode two lines carry ________ signals which are not identical to each other.

 Same (Page 109) different digital analog Question No: 12 ( Marks: 1 ) - Please choose one A ______________ converts an analog signal into a digital signal. Demodulator (Page 110) Modulator Digital-to-analog converter Question No: 13 ( Marks: 1 ) - Please choose one Which of the following is an example of ITU-T modem standards: T-series X-series N-series V-series

(Page 114)

Question No: 14 ( Marks: 1 ) - Please choose one The maximum data rate in the uploading direction is still ____________. 26.6 Kbps 33.6 Kbps 36.6 Kbps 46.6 Kbps

(Page 117)

Question No: 15 ( Marks: 1 ) - Please choose one Which of the following primarily uses guided media Cellular telephone system Local telephone system Satellite communication Radio broadcasting

(Page 120)

Question No: 16 ( Marks: 1 ) - Please choose one When a beam of light travels through media of two different densities, if the angle of incidence is greater than the critical angle, ____________occurs. Reflection Refraction (Page 127) Incidence Criticism Question No: 17 ( Marks: 1 ) - Please choose one When we talk about unguided media, usually we are referring to _________. Metallic wires Nonmetallic wires

 The air Water

(Page 132)

Question No: 18 ( Marks: 1 ) - Please choose one Optical fibers are defined by the ratio of the ___________ of their core to the diameter of their cladding. Diameter (Page 130) Radius Length Width Question No: 19 ( Marks: 1 ) - Please choose one All of popular Fiber optic connectors are ___________ shaped. Conical Barrel (Page 131) Circular Rectangular Question No: 20 ( Marks: 1 ) - Please choose one Radio wave transmission utilizes ___________ different types of propagation. Four Three Two Five

(Page 132)

Question No: 21 ( Marks: 1 ) - Please choose one dB is ____________ if a signal is amplified. Negative Positive (Page 142) Null Zero Question No: 22 (Marks: 1) - Please choose one A prism can deflect the light depending upon the angle of ____________ and the frequency. Deviation Incident (Page 151) Refraction (Page 127) Reflection Question No: 23 ( Marks: 1 ) - Please choose one Asynchronous TDM is efficient only when the size of the time slot is kept relatively _______________ Large (Page 158) Small Medium None of the given

Question No: 24 ( Marks: 1 ) - Please choose one The local loop has ___________ cable that connects the subscriber telephone to the nearest end office. Twisted-pair (Page 160) Coaxial Fiber-optic None of the given Question No: 25 ( Marks: 1 ) - Please choose one Data from a computer are ____________; the local loop handles _________ signals. Analog; analog Analog; digital Digital; digital Digital; analog

http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter9/multiple_choice_quiz.html
Question No: 26 ( Marks: 1 ) - Please choose one Which error detection method uses ones complement arithmetic? Simple parity check Two-dimensional parity check CRC Checksum (Page 179) Question No: 27 ( Marks: 1 ) - Please choose one Flow control is needed to prevent ____________ Bit errors Overflow of the sender buffer Overflow of the receiver buffer (Page 46) Collision between sender and receiver Question No: 28 ( Marks: 1 ) - Please choose one ____________ coordinates the amount of data that can be sent before receiving acknowledgment flow control (Page 186) error control data control Question No: 29 ( Marks: 1 ) - Please choose one Error control is both error _________ and error ___________ detection; correction (Page 186) detection; deletion detection; avoidance detection; forwarding Question No: 30 ( Marks: 1 ) - Please choose one Addressing is not needed in _______________ configuration.

 Point to Point (Page 190) Multipoint Point to point and multipoint Question No: 31 ( Marks: 1 ) - Please choose one In a Go-Back-N ARQ, if the window size is 63, what is the range of sequence number? 0 to 63 0 to 64 1 to 63 1 to 64

http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter11/multiple_choice_quiz.html
Question No: 32 ( Marks: 1 ) - Please choose one A timer is set when ___________ is sent out. A data frame An ACK (Page 197) A NAK Question No: 33 ( Marks: 1 ) - Please choose one Sliding window requires that data frames be transmitted _______________ Sequentially (Page 199) Frequently Synchronously Asynchronously Question No: 34 ( Marks: 1 ) - Please choose one In Y-MODEM Multiple files can be sent simultaneously True False

(Page 205)

Question No: 35 ( Marks: 1 ) - Please choose one BLAST stands for : Blocked asynchronous transmission (Page 205) Blocked synchronous transmission Barrel asynchronous transmission Below asynchronous transmission Question No: 36 ( Marks: 1 ) - Please choose one HDLC is an acronym for ______________. High-duplex line communication High-level data link control (Page 210) Half-duplex digital link combination Host double-level circuit Question No: 37 ( Marks: 1 ) Please choose one

The HDLC ___________ field defines the beginning and end of a frame. Flag (Page 214) Address Control FCS Question No: 38 ( Marks: 1 ) Please choose one _________ is the access protocol used by traditional Ethernet. CSMA/CD (Page 222) CSMA/CA Token Ring CSMA Question No: 39 ( Marks: 1 ) Please choose one Bridges can divide a large ________ into smaller segments Network (Page 241) Packet Frame Address Question No: 40 ( Marks: 1 ) Please choose one Like VRC, LRC and CRC, Checksum is also based on _______________. Redundancy (Page 179) Decimal Division Encryption Encoding

FINALTERM EXAMINATION Fall 2009

Question No: 1 ( Marks: 1 ) Please choose one The information to be communicated in a data communications system is the Medium Protocol Message (Page 7) Transmission Question No: 2 ( Marks: 1 ) Please choose one A set of devices connected by communication links is called networking True (Page 12) False

Question No: 3 ( Marks: 1 ) Please choose one Internet with small i specifies the world wide Network the actual internet. True False (Page 39) Question No: 4 ( Marks: 1 ) Please choose one Data chunk at data link layer is called________ frame packet (Page 38) datagram Question No: 5 ( Marks: 1 ) Please choose one Data synchronization is a function related with ___________ session layer (Page 51) presentation layer transport Question No: 6 ( Marks: 1 ) Please choose one When data are transmitted from device A to device B, the header from As layer 4 is read by Bs __________ layer. physical transport application none of the given http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter2/multiple_choice_quiz.html Question No: 7 ( Marks: 1 ) Please choose one Data must be converted into__________ before transmission. signal (Page 56 and 84) wave electric pulse Question No: 8 ( Marks: 1 ) Please choose one PCM is the first process of PAM. True False (Page 80) Question No: 9 ( Marks: 1 ) Please choose one In _____________ transmission, bits are transmitted over a single wire, one at a time.

 Asynchronous serial Synchronous serial Parallel (Page 98) Asynchronous & Synchronous serial Question No: 10 ( Marks: 1 ) Please choose one EIA 232 allows for a maximum bit rate of __________Kbps. 40 30 20 (Page 104) 10 Question No: 11 ( Marks: 1 ) Please choose one When a beam of light travels through media of two different densities, if the angle of incidence is greater than the critical angle, ____________occurs. Reflection Refraction (Page 127) Incidence Criticism Question No: 12 ( Marks: 1 ) Please choose one A parabolic dish antenna is a(n) ______________ antenna. Omnidirectional Bidirectional Unidirectional (Page 138) Horn Question No: 13 ( Marks: 1 ) Please choose one Ultra high-frequency waves always use __________ propagation. Ground Sky Line of Sight (Page 136) Space Question No: 14 ( Marks: 1 ) Please choose one Middle frequency waves having range 300 KHz-3 MHz always use __________ propagation. Ground Sky Line of Sight Space
http://www.scribd.com/doc/22810820/Data-Communication-and-Networking

Page 8 of this book.

Question No: 15 ( Marks: 1 ) Please choose one DB is ____________ if a signal is attenuated. Negative (Page 142) Positive Null Zero Question No: 16 ( Marks: 1 ) Please choose one Which multiplexing technique involves signals composed of light beams? FDM TDM WDM (Page 150) none of the given Question No: 17 ( Marks: 1 ) Please choose one Multiplexing has long been used as an essential tool in the ____________. Electronic industry Telephone industry (Page 159) Space science VLAN Question No: 18 ( Marks: 1 ) Please choose one A telephone network is an example of a __________ network. Packet-switched Circuit-switched (Page 38) Message-switched none of the given Question No: 19 ( Marks: 1 ) Please choose one The local loop has ___________ cable that connects the subscriber telephone to the nearest end office. Twisted-pair (Page 160) Coaxial Fiber-optic None of the given Question No: 20 ( Marks: 1 ) Please choose one Which error detection method involves polynomials? Checksum Two-dimensional parity check CRC (Page 177) Simple parity check

Question No: 21 ( Marks: 1 ) Please choose one In CRC there is no error if the remainder at the receiver is ____________ Equal to the remainder at the sender Zero (Page 176) Nonzero The quotient at the sender Question No: 22 ( Marks: 1 ) Please choose one In CRC the quotient at the sender _____________ Becomes the dividend at the receiver Becomes the divisor at the receiver is discarded is the remainder http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 23 ( Marks: 1 ) Please choose one Which error detection method can detect a bust error? The parity check Two-dimensional parity check CRC Two-dimensional parity check and CRC http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 24 ( Marks: 1 ) Please choose one At the CRC checker, ________ means that the data unit is damaged A string of 0s A string of 1s A string of alternating 1s and 0s A nonzero remainder http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 25 ( Marks: 1 ) Please choose one Error control is both error _________ and error ___________ detection; correction (Page 186) detection; deletion detection; avoidance detection; forwarding Question No: 26 ( Marks: 1 ) Please choose one In line discipline the initiator first transmits a frame called an ________

 Enquiry (Page 189) Acknowledgment NAK Request Question No: 27 ( Marks: 1 ) Please choose one In line discipline after the data transmission, the sending system finishes with an _____________ frame EOT (Page 189) EKT ENT ESP Question No: 28 ( Marks: 1 ) Please choose one In primary-secondary communication ______________ is always the initiator of a session Primary (Page 189) Secondary Sender Receiver Question No: 29 ( Marks: 1 ) Please choose one Primary device uses ____________ to receive transmission from the secondary devices. ACK ENQ POLL (Page 191) Question No: 30 ( Marks: 1 ) Please choose one In a Go-Back-N ARQ, if the window size is 63, what is the range of sequence number? 0 to 63 0 to 64 1 to 63 1 to 64 http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter11/multiple_choice_quiz.html Question No: 31 ( Marks: 1 ) Please choose one Sliding window requires that data frames be transmitted _______________ Sequentially (Page 199) Frequently Synchronously Asynchronously Question No: 32 ( Marks: 1 ) Please choose one

Data link protocols can be divided into ______________ sub-groups. two (Page 202) three four five Question No: 33 ( Marks: 1 ) Please choose one XMODEM is a ______________ protocol designed for telephone-line communication b/w PCs. file transfer (Page 203) hardware software application exchange Question No: 34 ( Marks: 1 ) Please choose one In Y-MODEM Multiple files can be sent simultaneously True (Page 205) False Question No: 35 ( Marks: 1 ) Please choose one Which of the following combines features of the other two? ZMODEM (Page 205) YMODEM XMODEM None of given Question No: 36 ( Marks: 1 ) Please choose one BLAST stands for : Blocked asynchronous transmission (Page 205) Blocked synchronous transmission Barrel asynchronous transmission Below asynchronous transmission Question No: 37 ( Marks: 1 ) Please choose one

Which one of the following uses full duplex operation with sliding window flow control.

BLAST (Page 205) XMODEM YMODEM ZMODEM

Question No: 38 ( Marks: 1 ) Please choose one HDLC is an acronym for ______________. High-duplex line communication High-level data link control (Page 210) Half-duplex digital link combination Host double-level circuit Question No: 39 ( Marks: 1 ) Please choose one The DSAP and SSAP are addresses used by _________ to identify the protocol stacks. LLC (Page 220) MAC Network Question No: 40 ( Marks: 1 ) Please choose one The PDU has no flag fields, no CRC, and no station address TRUE (Page 220) FALSE Question No: 41 ( Marks: 1 ) Please choose one Which of the following is a bus topology LAN that uses base band signaling and has a max? segment length of 500 meters 10 Base5 (Page 223) 10 Base2 100 Base2 100 Base5 Question No: 42 ( Marks: 1 ) Please choose one Token Bus has no commercial application in data communications True (Page 232) False Question No: 43 ( Marks: 1 ) Please choose one The BNC-T connector is a T-shaped device with _______ ports Three (Page 228) Two Four Five Question No: 44 ( Marks: 1 ) Please choose one _________ is the access protocol used by traditional Ethernet.

 CSMA/CD (Page 222) CSMA/CA Token Ring CSMA http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter13/mixed_quiz.html Question No: 45 ( Marks: 1 ) Please choose one When a collision is detected in a network using CSMA/CD. _________ The frame is immediately resent A jam signal is sent by the station The backoff value is set to 0 The backoff value is decremented by 1
http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter13/mixed_quiz.html

Question No: 46 ( Marks: 1 ) Please choose one Like VRC, LRC and CRC, Checksum is also based on _______________. Redundancy (Page 179) Decimal Division Encryption Encoding Question No: 47 ( Marks: 1 ) Please choose one Check sum method is used for _______________ layers. Physical Application Transport Data link

http://www.cse.iitk.ac.in/users/dheeraj/cs425/lec09.html

Question No: 48 ( Marks: 1 ) Please choose one Repeater works on __________ layer. Data Link Physical Network (Page 224) Application

Question No: 49 ( Marks: 1 ) Please choose one When systems share a point to point link, then protocols used are called ___________ protocols. Direct (Page 21) Indirect

 Monolithic structured Question No: 50 ( Marks: 1 ) Please choose one _________ requires more bandwidth. FSK http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter5/ ASK PSK QAM

Fall 2009 CS601- Data Communication

Question No: 1 ( Marks: 1 ) Please choose one An unauthorized user is a network ___________ issue. Performance Reliability Security (Page 15) All of the given Question No: 2 ( Marks: 1 ) Please choose one Which is not an element of protocol? semantics timing communication service module (Page 19) Question No: 3 ( Marks: 1 ) Please choose one _______ is a multipoint topology. Ring Mesh Tree Bus (Page 31) Question No: 4 ( Marks: 1 ) Please choose one Unidirectional traffic movement is overcome by dual ring technology. True (Page 33) False Question No: 5 ( Marks: 1 ) Please choose one Physical layer define characteristics of interface between device and _________ transmission medium another device http://en.wikipedia.org/wiki/OSI_model

 another peer physical layer at other side modem Question No: 6 ( Marks: 1 ) Please choose one ________ layer deals with syntax and semantics of information exchange. presentation (Page 51) session application physical Question No: 7 ( Marks: 1 ) Please choose one To allow access to network resources is the function of ___________ application layer (Page 53) physical layer network layer Question No: 8 ( Marks: 1 ) Please choose one Time domain plot show changes in signal phase with respect to time. True False (Page 63) Question No: 9 ( Marks: 1 ) Please choose one In 8QAM each signal shift or one baud represents ______. 4 bits 2 bits 5 bits 3 bits (Page 93) Question No: 10 ( Marks: 1 ) Please choose one Modulation of an analog signal can be accomplished through changing the ___________ of the carrier signal. amplitude frequency phase all of the given (Page 62) Question No: 11 ( Marks: 1 ) Please choose one EIA 449 provides much better functionality than EIA ________ 232 (Page 110) 223

 262 222 Question No: 12 ( Marks: 1 ) Please choose one Which of the following is an example of ITU-T modem standards: T-series X-series N-series V-series (Page 114) Question No: 13 ( Marks: 1 ) Please choose one Traditional modems are wide spread now to a data rate of __________. 56 Kbps (Page 115) 72 Kbps 42 Kbps 96 Kbps Question No: 14 ( Marks: 1 ) Please choose one In case of uploading at the switching station, data is converted to digital signal using ___________. TCP PCM (Page 116) ICP TDM Question No: 15 ( Marks: 1 ) Please choose one The RG number gives us information about ________. Twisted pairs Coaxial cables (Page 125) Optical fibers all of the given Question No: 16 ( Marks: 1 ) Please choose one The _________ is an association that sponsors the use of infrared waves. IrDA http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter7/mixed_quiz.html EIA FCC PUD Question No: 17 ( Marks: 1 ) Please choose one Optical fibers are defined by the ratio of the ___________ of their core to the diameter of their cladding.

 Diameter (Page 130) Radius Length Width Question No: 18 ( Marks: 1 ) Please choose one The section of EM spectrum defined as Radio Communication is divided into _____ ranges called BANDS. 8 10 5 6 (Page 132)

Question No: 19 ( Marks: 1 ) Please choose one Radio wave transmission utilizes ___________ different types of propagation. Four Three Two Five (Page 132) Question No: 20 ( Marks: 1 ) Please choose one The VLF and LF bands use _________ propagation for communications. Ground Sky Line of sight Space

(Page 136)

Question No: 21 ( Marks: 1 ) Please choose one In __________ propagation, low-frequency radio waves hug the earth. Ground Sky Line of Sight Space (Page 133) Question No: 22 ( Marks: 1 ) Please choose one dB is ____________ if a signal is amplified. Negative Positive Null Zero

(Page 142)

Question No: 23 ( Marks: 1 ) Please choose one Distortion occurs in a ___________ signal. Rectified Composite (Page 141) Amplified none of the given Question No: 24 ( Marks: 1 ) Please choose one There are ________ basic categories of multiplexing. 3 (Page 148) 4 2 5 Question No: 25 ( Marks: 1 ) Please choose one In bit ____________, MUX adds extra bits to a device. Stuffing (Page 156) Adding Multiplication Exchanging Question No: 26 ( Marks: 1 ) Please choose one The local loop has ___________ cable that connects the subscriber telephone to the nearest end office. Twisted-pair (Page 160) Coaxial Fiber-optic None of the given Question No: 27 ( Marks: 1 ) Please choose one FTTC stands for _____________ flexible to the curb fiber to the curb (Page 166) fiber to the cable fiber to the center Question No: 28 ( Marks: 1 ) Please choose one If the ASCII character G is sent and the character D is received, what type of error is this? Single-bit Multiple-bit Burst

 Recoverable
http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html

Question No: 29 ( Marks: 1 ) Please choose one Which error detection method can detect a single-bit error? Simple parity check Two-dimensional parity check CRC All of the given
http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html

Question No: 30 ( Marks: 1 ) Please choose one Flow control is needed to prevent ____________ Bit errors Overflow of the sender buffer Overflow of the receiver buffer (Page 46) Collision between sender and receiver Question No: 31 ( Marks: 1 ) Please choose one In data link layer, communication requires at least ___________ devices working together 3 2 (Page 185) 4 5 Question No: 32 ( Marks: 1 ) Please choose one Data link control is composed of ____________ important functions. 2 3 (Page 185) 4 5 Question No: 33 ( Marks: 1 ) Please choose one ____________ coordinates the amount of data that can be sent before receiving acknowledgment flow control (Page 186) error control data control

Question No: 34 ( Marks: 1 ) Please choose one Primary device uses ____________ to receive transmission from the secondary devices.

 ACK ENQ POLL

(Page 191)

Question No: 35 ( Marks: 1 ) Please choose one In a Go-Back-N ARQ, if the window size is 63, what is the range of sequence number? 0 to 63 0 to 64 1 to 63 1 to 64 http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter11/multiple_choice_quiz.html Question No: 36 ( Marks: 1 ) Please choose one Data link protocols can be divided into ______________ sub-groups. two (Page 202) three four five Question No: 37 ( Marks: 1 ) Please choose one XMODEM is a ______________ protocol designed for telephone-line communication b/w PCs. file transfer (Page 203) hardware software application exchange Question No: 38 ( Marks: 1 ) Please choose one YMODEM uses ITU-T CRC-_____ for Error Checking 16 32 8 4 (Page 205)

Question No: 39 ( Marks: 1 ) Please choose one In Y-MODEM Multiple files can be sent simultaneously True False (Page 205)

Question No: 40 ( Marks: 1 ) Please choose one HDLC is an acronym for ______________.

 High-duplex line communication High-level data link control (Page 210) Half-duplex digital link combination Host double-level circuit Question No: 41 ( Marks: 1 ) - Please choose one What is present in all HDLC control fields? P/F bit (Page 215) N(R) N(S) Code bits Question No: 42 ( Marks: 1 ) - Please choose one Which of the following sublyer, resolves the contention for the shared media MAC (Page 219) LLC Physical Question No: 43 ( Marks: 1 ) - Please choose one Ethernet LANs can support data rates between _____________ 1 and 100 Mbps (Page 223) 1 and 200 Mbps 1 and 500 Mbps 1 and 100 Gbps Question No: 44 ( Marks: 1 ) - Please choose one In FDDI, Token Passing is used as Access method. True False (Page 236)

Question No: 45 ( Marks: 1 ) - Please choose one Bridges can divide a large ________ into smaller segments Network (Page 241) Packet Frame Address Question No: 46 ( Marks: 1 ) - Please choose one Like VRC, LRC and CRC, Checksum is also based on _______________.

 Redundancy (Page 179) Decimal Division Encryption Encoding Question No: 47 ( Marks: 1 ) - Please choose one Check sum method is used for _______________ layers. Physical Application Transport Data link Question No: 48

http://www.cse.iitk.ac.in/users/dheeraj/cs425/lec09.html ( Marks: 1 ) - Please choose one

Which of the following ___________ uses a series of filters to decompose multiplexed signal into its constituent signals? Bridge MUX DEMUX Switch Question No: 49

(Page 150)

( Marks: 1 ) - Please choose one We need

____________ to decompose a composite signal into its components. Fourier transform (Page 64) nyquist theorem shannon capacity Question No: 50 ( Marks: 1 ) - Please choose one Data from computer is in ____________ form and the local loop handles _________ signals. Analog; analog Analog; digital Digital; digital Digital; analog
http://highered.mcgraw-hill.com/sites/0072967757/student_view0/chapter9/multiple_choice_quiz.html

FINALTERM EXAMINATION Spring 2009

Question No: 1 ( Marks: 1 ) - Please choose one There are how many factors on which the performance of a network depends?

 Three Five (Page 14) Four Two Question No: 2 ( Marks: 1 ) - Please choose one _________requires the maximum number of I/O ports. Bus Star Mesh (Page 29) Ring Question No: 3 ( Marks: 1 ) - Please choose one Headers are added at layers 1 and 7 of OSI model. True False (Page 41) Question No: 4 ( Marks: 1 ) - Please choose one Trailer is only added at ________layer of OSI model. data link (Page 41) physical network application Question No: 5 ( Marks: 1 ) - Please choose one A sine wave must be an analog signal. True (Page 58) False Question No: 6 ( Marks: 1 ) - Please choose one If there is __________in voltage then the frequency is infinite. instantaneous change (Page 61) continuous change no change Question No: 7 ( Marks: 1 ) - Please choose one The inversion of the level at 1 bit is called as __________ NRZ-L NRZ-I (Page 73)

 RZ Question No: 8 ( Marks: 1 ) - Please choose one The last process in PCM is _________ digital data into digital signal. encoding (Page 82) decoding modulating Question No: 9 ( Marks: 1 ) - Please choose one Amplitude in ASK is more resistive to EMI and Noise. True False (Page 87) Question No: 10 ( Marks: 1 ) - Please choose one If FCC regulations are followed, the carrier frequencies of adjacent AM radio stations are ____________ apart. 5 KHz 10 KHz (Page 95) 200 KHz 530 KHz Question No: 11 ( Marks: 1 ) - Please choose one In _____________ transmission, a start bit and a stop bit frame a character byte. Asynchronous serial (Page 99) Synchronous serial Parallel Asynchronous & Synchronous serial Question No: 12 ( Marks: 1 ) - Please choose one Synchronous transmissions have _____________. a start bit a stop bit gaps between bytes none of the given (Page 99) Question No: 13 ( Marks: 1 ) - Please choose one Transmission media are usually categorized as _____________ Fixed or Unfixed Guided or Unguided (Page 119) Determinate or Indeterminate

 Metallic or Nonmetallic Question No: 14 ( Marks: 1 ) - Please choose one The RG number gives us information about ________. Twisted pairs Coaxial cables (Page 125) Optical fibers all of the given Question No: 15 ( Marks: 1 ) - Please choose one Radio wave and microwave frequencies range from _________. 3 to 300 KHz 300 KHz to 300GHz (Page 132) 3 KHz to 300 GHz 3 KHz to 3000 GHz Question No: 16 ( Marks: 1 ) - Please choose one All of popular Fiber optic connectors are ___________ shaped. Conical Barrel (Page 131) Circular Rectangular Question No: 17 ( Marks: 1 ) - Please choose one In ______________ method a signal can be directed in a straight from Antenna to antenna. Line of sight (Page 134) Ground propagation Sky propagation Microwaves Question No: 18 ( Marks: 1 ) - Please choose one Amplifiers are used to __________the signal to heat. Amplify (Page 142) Rectify Testify Nullify Question No: 19 ( Marks: 1 ) - Please choose one There are ________ basic categories of multiplexing. 3 (Page 148)

4 2 5 Question No: 20 ( Marks: 1 ) - Please choose one If a T-1 carries 8000 frames, the data rate is ___________ 2.544 Mbps 1.544 Mbps (Page 165) 1.544 Kbps 1.544 Gbps Question No: 21 ( Marks: 1 ) - Please choose one FTTC stands for _____________ flexible to the curb fiber to the curb (Page 166) fiber to the cable fiber to the center

Question No: 22 ( Marks: 1 ) - Please choose one Optical signals are multiplexed using _________ at switching office to create wider BW optical signals WDM (Page 167) FDM TDM MUX Question No: 23 ( Marks: 1 ) - Please choose one Which error detection method consists of a parity bit for each unit as well as an entire data unit of parity bits? Simple parity check Two-dimensional parity check http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html CRC Checksum Question No: 24 ( Marks: 1 ) - Please choose one If the ASCII character G is sent and the character D is received, what type of error is this? Single-bit Multiple-bit Burst

http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Recoverable Question No: 25 ( Marks: 1 ) - Please choose one Flow control is needed to prevent ____________ Bit errors Overflow of the sender buffer Overflow of the receiver buffer. (Page 46) Collision between sender and receiver Question No: 26 ( Marks: 1 ) - Please choose one In data link layer, communication requires at least ___________ devices working together 3 2 4 5

(Page 185)

Question No: 27 ( Marks: 1 ) - Please choose one Data link control is composed of ____________ important functions. 2 3 4 5

(Page 185)

Question No: 28 ( Marks: 1 ) - Please choose one Error control is both error _________ and error ___________ detection; correction detection; deletion detection; avoidance detection; forwarding (Page 186)

Question No: 29 ( Marks: 1 ) - Please choose one ENQ/ACK stands for______________ Enquiry/ Acknowledgment Enque/ Acknowledgment Enquist/ Acknowledgment none of the given (Page 187)

Question No: 30 ( Marks: 1 ) - Please choose one In __________ ARQ, if a NAK is received, only the specific damaged or lost frame is retransmitted.

 Stop-and-wait Go-Back-N Selective reject (Page 200) Stop-and-wait & Go-back-N Question No: 31 ( Marks: 1 ) - Please choose one Sliding window requires that data frames be transmitted _______________ Sequentially (Page 199) Frequently Synchronously Asynchronously Question No: 32 ( Marks: 1 ) - Please choose one Which of the following combines features of the other two? ZMODEM (Page 205) YMODEM XMODEM None of given Question No: 33 ( Marks: 1 ) - Please choose one BLAST stands for : Blocked asynchronous transmission (Page 205) Blocked synchronous transmission Barrel asynchronous transmission Below asynchronous transmission

Question No: 34 ( Marks: 1 ) - Please choose one HDLC is an acronym for ______________. High-duplex line communication High-level data link control (Page 210) Half-duplex digital link combination Host double-level circuit Question No: 35 ( Marks: 1 ) Please choose one The HDLC ___________ field defines the beginning and end of a frame. Flag (Page 214) Address Control FCS

Question No: 36 ( Marks: 1 ) Please choose one The shortest frame in HDLC protocol is usually the _________ frame. Information Supervisory (Page 213) Management None of the given Question No: 37 ( Marks: 1 ) - Please choose one The PDU has no flag fields, no CRC, and no station address TRUE (Page 220) FALSE Question No: 38 ( Marks: 1 ) - Please choose one _________ is the access protocol used by traditional Ethernet. CSMA/CD (Page 222) CSMA/CA Token Ring CSMA http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html Question No: 39 ( Marks: 1 ) - Please choose one Repeater is an amplifier, not a regenerator. True False (Page 240) Question No: 40 ( Marks: 1 ) - Please choose one Bridges can divide a large ________ into smaller segments Network (Page 241) Packet Frame Address

CS601 Data Communication Final Term Examination Spring 2006

Question No. 1 Marks : 2

Which error detection method uses ones complement arithmetic? Simple parity check Two-dimensional parity check CRC Checksum (Page 179)

Question No. 2 Marks : 2

In a time-domain plot, the vertical axis is the measure of ________. Amplitude (Page 59) Frequency Phase Time
Question No. 4 Marks : 2

Which topology requires a multipoint connection? Mesh Star Bus (Page 31) Ring
Question No. 8 Marks : 2

A timer is set when ___________ is (are) sent out. A data frame An ACK (Page 197) A NAK An ARQ
Question No. 9 Marks : 2

If the data unit is 111111, the divisor 1010, and the remainder 110, what is the dividend at the receiver? 111111011 111111110 http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html 1010110 110111111

FINALTERM EXAMINATION FALL 2006

Question No: 1 ( Marks: 1 ) - Please choose one OSI standard is practically implemented in the form of internet. TRUE FALSE Question No: 2 ( Marks: 1 ) - Please choose one TCP/IP application layers combine the functions of OSI Application, Session and Transport layers. TRUE (Page 55) FALSE

Question No: 3 ( Marks: 1 ) - Please choose one Unipolar use one voltage levels. TRUE (Page 71) FALSE Question No: 4 ( Marks: 1 ) - Please choose one The material of core and cladding in fiber optic cable is same. TRUE FALSE (Page 127) Question No: 5 ( Marks: 1 ) - Please choose one Burst error is easily corrected then bit error. TRUE FALSE Question No: 6 ( Marks: 1 ) - Please choose one Set of rules governing communication is known as OSI model Protocol (Page 08) Medium Question No: 7 ( Marks: 1 ) - Please choose one WDM(wave division multiplexing) deals with electric waves light waves (Page 150) both Question No: 8 ( Marks: 1 ) - Please choose one A Null modem is a traditional modem technique to connect two DTE (Page 106) both Question No: 9 ( Marks: 1 ) - Please choose one Router work on data link layer physical layer network layer (Page 48) Question No: 10 ( Marks: 1 ) - Please choose one Poll/Select is a technique related with line control line discipline (Page 187)

error control

Final Term Examination Spring 2005

Question No. 1 Marks : 02

In cyclic redundancy checking, what is the CRC?

the divisor the quotient the dividend the remainder

http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html
Question No. 2 Marks : 02

In fiber optics the signal source is ____________waves.

Light (Page 126) Radio Very Low frequency Infrared

Question No. 3 Marks : 02

Each device has a dedicated point to point line configuration only with the two devices on either side of it.

Ring Topology (Page 33) Star Topology Mesh Topology Tree Topology
Question No. 6 Marks : 02

Measures the relative strengths of two signals

Decibel (Page 141) Bandwidth Wavelength Phase

Question No. 7 Marks : 02

Which multiplexing technique shifts each signal to a different carrier frequency?

FDM (Page 149)

Synchronous TDM Asynchronous TDM None of the above

Question No. 8 Marks : 02

The _____________of a signal is the width of the frequency spectrum.

Amplitude Bandwidth (Page 66) Bit interval Phase

Final Term Examination Spring 2005

Question No. 1

In cyclic redundancy checking, what is the CRC?

Marks : 02

the divisor the quotient the dividend the remainder

http://highered.mcgraw-hill.com/sites/0072515848/student_view0/chapter10/mixed_quiz.html
Question No. 2

In fiber optics the signal source is ____________waves.

Marks : 02

Light (Page 126) Radio Infrared Very Low frequency

Question No. 3 Marks : 02

Each device has a dedicated point to point line configuration only with the two devices on either side of it.

Ring Topology (Page 33) Mesh Topology Star Topology Tree Topology
Question No. 6

Measures the relative strengths of two signals

Marks : 02

Decibel (Page 141) Bandwidth Phase Wavelength

Question No. 7 Marks : 02

Which multiplexing technique shifts each signal to a different carrier frequency?

FDM (Page 149) Synchronous TDM Asynchronous TDM None of the above
Question No. 8

The _____________of a signal is the width of the frequency spectrum.

Marks : 02

Amplitude Bandwidth (Page 66) Bit interval Phase