Scribd
Upload
49 views4 pages

Figure 1: Adam Internal Cabling

The document provides details on the internal and external cabling for an ADAM data acquisition system. It includes diagrams of the internal cabling between boards in the VME chassis as well as the external cabling connecting sensors. Notes are provided on powering the system and proper grounding of signal shields. The filter amplifier board and its jumper settings for gain and offset are also described.

Uploaded by

Prasanna Kumar Das
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
49 views4 pages

Figure 1: Adam Internal Cabling

The document provides details on the internal and external cabling for an ADAM data acquisition system. It includes diagrams of the internal cabling between boards in the VME chassis as well as the external cabling connecting sensors. Notes are provided on powering the system and proper grounding of signal shields. The filter amplifier board and its jumper settings for gain and offset are also described.

Uploaded by

Prasanna Kumar Das
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

ADAM Internal Cabling

ElectroThermal Cooler
Mx 320 Iro CP n or ics U IV3 IV16 234 24 16 8P Iro nic Po ort, rt S sC a IO b Iro les Ba nics nk Ca 2 fo ble r I s, Da V3 tel 234 641 A/D Da Ex ten tel 601 der A/D

Note/Beware: Switch on Cooler powers up/down everything, including VME chassis! Switch on Power Supply only toggles VME chassis.

Am p

Am p

Am p

en slo ts

Filt er /

Filt er /

Filt er /

Ma trix

NOTE: No open slots allowed between CPU and A/D boards (or else put jumpers on the interrupt line).

Op

1
Channel 0

2
To misc. bulkhead connectors: Console port, SerA, etc.

See Datel Filter AutoZero Cable below

PB

4
Ribbon Cables: Pin 1 to 1, etc.

Ethernet Transceiver

PA

SIO ribbon cables to Ironics, ch07 on upper bank

ADChannels: 07 from 4port 0,1 Cables: (hard wired internally from bulkhead to backplane.)

815 1623 2431 3239 4047 4,5 6,7 8,9 10,11 2,3

1st 641, Differential Mode Switch S1 set for ch. 1631


3 2 1 0 7 6 5 4

Ch.03 1 via SIO Cable0

Ch.47 via SIO Cable1

ch815 on lower bank

Datel 601 Filter / Ampl. AutoZero Cable


DB25 Gnd: 12 Gnd: 13 I/O Bit3: 24 I/O Bit4: 25 DB9 2: (nc) 1: Gnd 4,7: AutoZero Switch 5,6: Output Switch

Ch.811 via SIO Cable2

Ch.1215 via SIO Cable3

Internal Serial Ribbon Cable Wiring


Top View of Ironics breakout board Gnd CTS (to Ironics) Rx (to Ironics) DTR (from Ironics)
1

Tx (from Ironics)

Figure 1: Adam Internal Cabling

Channel 7

Po w

er Su p

ply .

l.

l.

l.

ADAM External Cabling


AC Input 03

Elec.Box Connector Panel


Serial Analog
1619 2023 4043 4447 47
Tx

Ether Fiber Rx

Terminal
Grounded Recepticle DC Pwr out AC

Located on Side of box

811 811 1215 03

1215 3235 3639

Switch
On

47

2427 2831

Off

Reset Unused

SerA

A/Cin

Power Dist. Box


Bottom View

Chassis Serial Cable Wiring


4 9 15 20 24 14 19 23 8 13 18 3 7 12 17 22 2 6 11 16 21 1 5 10

Chassis Analog Cable Wiring


2 6 10 14 13 16 5 9 12 15 4 8 11 1 3 7

1 = SIO1 (Rx) 2 = SIO1 (Tx) 3 = SIO1 (DTR) 4 = SIO1 (Gnd) 5 = SIO1 Shield 69,15= SIO2... 1014 = SIO3... 1620 = SIO4... 2124 = open

1 = AD1 (+) 2 = AD1 () 3 = AD1 shield 46 = AD2... 79 = AD3... 1012= AD4... 1316=open

Serial Breakout Box


DC 03:out in out 47:out

Analog Breakout Box


BreakOut Box Power Cabling
1 2 4 3

DC 03:out in out 47:out

1 2 inputs 5 6

1 2 3 4

= = = =

+12VDC +12VDC gnd gnd

1 2 inputs 5 6

To Sensors

To Sensors

Serial BreakOut Box Cabling


3 6 9 2 5 8 1 4 7

Analog BreakOut Box Cabling


3 6 9 2 5 8 1 4 7

1 2 3 4 5 6 7 8 9

= = = = = = = = =

Rx (Sensor to Adam) Tx (Adam to Sensor) DTR grnd open shield pwr grnd +12VDC open

1 2 3 4 5 6 7 8 9

= = = = = = = = =

analog + common shield open open open pwr grnd +12VDC open

Figure 2: ADAM External Cabling

ADAM FilterAmp. Board


Analog Output Connector Wiring Channel 0 1 2 3 4 5 6 Output 24 10 21 7 18 4 15 Ground 12 23 9 20 6 17 3 Connected to ground: 2,5,8,11,16,19,22,25
1 13

Beware: Leave W7,W8 disconnected for normal operation. Used for standalone testing: provides continuous autozeroing of amp. 7 1 14

AutoZero Connector Wiring See Adam Internal Cabling


5 1

J1 DB25 Analog Out Gnd 15 +15

J2 DB9 AutoZero W7 W8

Filter Module

Filter Module

Filter Module

Filter Module Filter Module Filter Module Filter Module Filter Module
Filter Module Identification:

Output W4 W5

Output W4 W5

Output W4 W5

Output W4 W5 W4 W5 W4 W5 W4 W5 W4 W5 Output Output Output Output

R3: 324K 1/2 Hz Filter Module

R3: 16.2K 10 Hz Filter Module

W3 W2 W1

W3 W2 W1

W3 W2 W1

W3 W2 W1

W3 W2 W1

W3 W2 W1

W3 W2 W1

W3 W2 W1

Channel 7 W76 W66

Channel 6 W56 W46

Channel 5 W36

Channel 4 Channel 3
C B A
1

W26

Channel 2

Channel 1

Channel 0

Analog Inputs from bulkhead


32

W06

W16 NOTE: For best A/D noise immunity, Shields should float inside ADAM Chassis: connect to gnd at sensor end. BEWARE: FilterAmp board jumpers W6 (labeled W06 W76 for respective channels) connect shields to gnd inside the chassis. Remove those jumpers if the shield wire is connected to ground at the sensorend NOTE: Datel 601 A/D Board samples +/5.0 Volts only.

Channel +Signal Signal Shield

Analog Input Connector Wiring 0 1 2 3 4 5 1A 5A 9A 13A 17A 21A 1C 5C 9C 13C 17C 21C 2A 6A 10A 14A 18A 22A

6 25A 25C 26A

7 29A 29C 30A

Filt/Amp. board Jumpering for gain/offset.


Jumper Gain Offset RangeV Volts W4 none W4,W5Rt W5Rt W5Lft W1,W4 W1,W4,W5Rt W1 W1,W5Rt W1,W5Lft W2,W4 W2,W4,W5Rt W2 W2,W5Rt W2,W5Lft W3,W4 W3,W4,W5Rt W3 W3,W5Rt W3,W5Lft .5 1 1 2 2 5 10 10 20 20 50 100 100 200 200 500 1000 1000 2000 2000 none none 5V 5V none none 5V none 5V none none 5V none 5V none none 5V none 5V none +/10.0 +/5.0 0,+10.0 0,+5.0 +/2.5 +/1.0 0,+1.0 +/0.50 0,+0.50 +/0.25 +/0.10 0,+0.1 +/50mV 0,+50mV +/25mV +/10mV 0,+10mV +/ 5mV 0,+ 5mV +/ 2.5mV A/D Res. 16bit MicroVolts 305.175 152.587 152.587 76.2939 76.2939 30.5175 15.2587 15.2587 7.62939 7.62939 3.051757 1,52587 1.52587 .762939 .762939 .305175 .152587 .152587 .0762939 .0762939 A/D Accuracy 14bit MicroVolts 1220.703 610.3515 610.3515 305.1757 305.1757 122.0703 61.03515 61.03515 30.51757 30.51757 12.20703 6.103515 6.103515 3.05175 3.05175 1.220703 .6103515 .6103515 .3051757 .3051757

Stage1 jumper, basic setting


Jumper none W1 W2 W3 Gain 1 10 100 1000

Stage2 jumper, multiplies gain in 1


Jumper none W4 W5 lft W5 rt Gain 1 0.5 2 2 Offset none none none 5V

Figure 3: Filter-Amplier Board Layout

The Book of ASTER

May 9, 2000

You might also like