API 571 for Inspectors Damage Mechanisms Affecting Fixed Equipment in the Refining Industry

Presenter: Charlie Buscemi

20 Years experience in the Petrochemical Industry Experience in corrosion, materials selection, research and development, and failure analysis Chevron, Connexsys, Stress Engineering Services (SES, Inc.) Currently Staff Consultant, SES, Inc. New Orleans office
2

API 571 for Inspectors

To Introduce inspectors to the general contents of API 571 To describe some common damage mechanisms Sources and References:
API 571 and Other API Standards NACE Recommended Practices ASM Metals Handbook

Common Alloys Used in the Petrochemical Industry

Carbon & Low-Alloy Steels

Carbon steel: all purpose HIC-resistant CS: wet H2S cracking resistance 1-1/4Cr-1/2Mo and 2-1/4Cr-1Mo: hightemperature strength, creep resistance, HTHA resistance 5Cr-1/2Mo, 7Cr-1Mo, 9Cr-1Mo: same as above, plus high-temperature sulfidation resistance (common furnace tube alloys) 12Cr (Type 410 SS): for high-temp sulfidation resistance (cladding & internals)
5

Stainless Steels
Chromium SS:

Type 410 (12% Cr), Type 430 (17% Cr) For high-temp sulfidation in non-hydrogen environments (esp. atmospheric Crude Units, vacuum units)

Austenitic SS:

300-series: Types 304/L, 316/L, 317, 321, 347 For H2/H2S environments (cladding, piping, internals in hydrocrackers, hydrotreaters) High-temperature services (FCC units) Heat exchanger shells, tubesheets, and tubes Furnace tubes
6

Specialty Alloys Aqueous Corrosion

Duplex SS (22Cr-5Ni-3Mo) for better SCC and
7

pitting resistance than 300-series SS (resists SCC to 200-250F, instead of 140F) Alloy 20 (29Cr-20Ni) for SCC resistance, also for sulfuric acid resistance in turbulent locations, especially pumps Monel 400 (for HCl acid resistance in Crude Unit distillation towers and overhead systems: trays, overhead piping, cladding) Hastelloy B, C, C-22, C-276 for acid corrosion
7

Alloys for High-Temperature Corrosion & Strength

Incoloy 800, 800H, 825 (35Ni-20Cr):
for high-temperature corrosion and high-Temp strength to 1650F Type 309, 310SS (25Cr, 12-20 Ni): high Cr concentration for oxidation resistance above 1600F (tube hangers, refractory anchors) Haynes, RA, HP, HK cast alloys (Co, W, Mo additions) for extreme high-temperature oxidation and strength (tubes, hangers, hydrogen manufacturing)
8

Heat Exchanger Alloys

Admiralty brass (cooling water exchangers) Copper-Nickel (90-10 Cu-Ni, 70-30 Cu-Ni):
better resistance to cooling water corrosion, especially in brackish or high-velocity streams Titanium (for heat exchanger tubes, especially in multi-corrosive locations, like Crude Unit overhead systems) -- Specify Gr. 7, 12 for hydriding resistance

API RP 571
Section 1 Intro & Scope (2 pgs.) Sec. 2 References (API, ASME,
10

ASTM, NACE, etc.) (2 pgs.) Sec. 3 Terms & Abbreviations (4 pgs.) Sec. 4 Damage Mechanisms -- All Industries (44 mechs., 152 pgs) Sec. 5 Damage Mechanisms -Refining industry (18 mechs., 61 pgs) PFDs (14 pgs.)
10

Example of a PFD Denoted with Damage Mechanisms

11

Section 4.2
Mechanical and Metallurgical
Failure Mechanisms All Industries

(Thermal effects, aging, embrittlement, creep & stress rupture, fatigue, erosion)
12

12

4.2.2: Spheroidization
Changes in CS and low-alloy
13

microstructure after long-term exposure at 850-1400F Carbide coarsening results in a decrease in high-temperature tensile and creep strength CS above ~ 800-850F 9Cr-1Mo above ~ 1000F
13

4.2.2: Spheroidization

14

14

4.2.2: Spheroidization
Occurs in:
Furnace tubes, hot-wall piping and equipment, FCC, coker, and cat reformer units, where temperature exceeds 850F

Usually a problem only at high stresses

(stress concentrations) since strength typically drops by 25-30% max.
15

15

4.2.2: Spheroidization

Inspection techniques:
-- Field Metallurgical Replication (FMR, replicas) -- Field hardness testing (Brinell) -- remove samples for lab analysis

16

16

4.2.5: 885F Embrittlement

Long-term exposure of duplex and
ferritic stainless steels (12Cr Types 405, 410, Duplex 2205) at 600-1000F Loss of ambient temperature ductility (on shutdowns) Ductility sufficient at operating temperature
17

17

4.2.5: 885F Embrittlement

Not pressure-containing components These alloys are used only for

18

internals in the susceptible temperature range (cladding, trays, etc. in FCC, coker, and Crude towers) May result in difficulty welding or straightening affected components
18

4.2.5: 885F Embrittlement

Inspection techniques:
-- Field hardness testing (Brinell) -- Bend test -- Charpy impact testing

19

19

4.2.6: Sigma Phase Embrittlement

Occurs in 300-series stainless steels

20

after long-term exposure to 10001700F Hard, brittle intermetallic phases are formed from the ferrite phase 321SS & 347SS are more susceptible than 304SS
20

4.2.6: Sigma Phase Embrittlement

Occurs in 3xx SS in very high

temperature services: -- FCC regenerator internals, -- catalyst slide valves, -- hydrogen plant furnace tubes -- styrene & other chemical plants
21

21

4.2.6: Prevention of Sigma Formation

Specify maximum ferrite content of 3-11%
in the finished weld

Limit the use of susceptible alloys in the

1100-1700F temperature range

Use Ferrite scope, DeLong diagram, Schaeffler

diagram to get proper ferrite content in the weld

22

22

4.2.6: Schaeffler Diagram

23

23

4.2.6: Sigma Phase Embrittlement

Before fabrication:
-- control ferrite (ferrite scope, Schaefler and DeLong diagrams)

Inspection techniques:
-- FMR -- remove samples for lab analysis -- Charpy impact test

To find & size cracks:

-- dye penetrant (PT); shear wave UT
24

24

4.2.8: Creep & Stress Rupture

25

25

4.2.8: Creep & Stress Rupture

Occurs at elevated temperatures

(see API 530): CS: 700F 5Cr: 800-850F 9Cr: 800-850F 300-series SS: 900F +
26

26

Creep in a CO boiler tube

Normal Top: 520-660F Took 8 years to fail (probably operated at
750-800F for some time)

27

27

Creep Voids and Fissures at 500X

28

28

4.2.8 Larson Miller Curves API 530

29

4.2.8: Stages of Creep

30

30

4.2.8: Creep & Stress Rupture

31

Affects furnace tubes, boiler tubes, hangers Internal creep voids grow and link together to form internal fissures and cracks Damage can be detected at 1/3 to 1/2 of creep life Bulging, go/no-go when expansion reaches 3-8%, depending on alloy
31

4.2.8: Creep & Stress Rupture

Inspection techniques: -- Visual inspection for bulges

-----Go/no-go gauging Strapping (diametral expansion) Radiography (RT) Ultrasonic thickness testing (UT) Field replication (FMR)
32

32

Monitor with TIs and infrared (IR) scans

4.2.9: Thermal Fatigue

All metals can undergo thermal

33

fatigue Cyclic stress due to alternating temperatures results in crack formation and propagation Typically forms wedge-shaped or carrot-shaped, scale-filled cracks
33

4.2.9: Thermal Fatigue

Wedge-Shaped, Oxide-Filled Cracks

34

34

4.2.9: Thermal Fatigue Where hot and cold streams

combine (injection points)

Boiler tubes, steam generating

equipment (quenching of hot tubes), coke drums

Coke drum girth welds, head-toshell welds, skirt welds

Smooth out weld contours

35

35

4.2.9: Thermal Fatigue

Inspection techniques: -- Visual inspection + -- Dye penetrant (PT) of stainless steel -- Wet fluorescent magnetic particle testing (WFMT) of carbon steels and Cr-Mo alloys -- External SWUT at attachment welds

36

36

4.2.16: Mechanical Fatigue

Due to cyclic stress Typical crack initiation sites: pits,
sharp corners, thread roots, grooves, notches

Mitigation: smooth out transitions,

blend weld crowns and notches, reduce stress, increase thickness, tensile strength
37

37

4.2.16: Mechanical Fatigue Characteristic

beach marks or clamshell marks Marks are the start-and-stop locations of crack propagation Clamshell marks are caused by exposure to corrosion, atmosphere, oxidation, thermal tinting
38

38

4.2.16: Mechanical Fatigue

Crack origin at a major transition in shaft thickness

39

39

4.2.16: Mechanical Fatigue

40

40

4.2.16: Mechanical Fatigue

41

41

4.2.16: Mechanical Fatigue

For some metals, an endurance limit
exists (CS, low-alloy steels, titanium) Below a particular stress, fatigue cracking will never occur Endurance limit is usually nearly half the tensile strength (UTS)

42

42

4.2.16: Mechanical Fatigue

For other metals, no limit exists
(stainless steels, non-ferrous alloys) Fatigue cracking will eventually occur The number of cycles required is a function of the alternating stress
43

43

Mechanical Fatigue Life

0.80 0.70 Length of Crack in. 0.60 0.50 0.40 0.30 0.20 0.10 0.00 (0.10) 0 10 20 30 40 50 60 70 80 90 98

Fatigue Life Expended (% )

44

44

4.2.16: Mechanical Fatigue

Inspection techniques:
-- Visual inspection at stress risers -- Check for oscillation, vibration -- Dye penetrant (PT) -- Wet fluorescent magnetic particle testing (WFMT) -- Shear wave UT
45

45

4.2.17: Vibration Fatigue

Susceptible equipment:
-- Piping attached to reciprocating and rotating equipment -- Pressure letdown valves and associated piping -- Relief valves -- Piping branch connections -- Heat exchanger tubes (esp. w/ thin-walled tubes)
46

46

Section 4.3
Uniform or Localized Loss of
Thickness All Industries Aqueous Corrosion

47

47

4.3.1: Galvanic Corrosion

Electrical current flowing between dissimilar metals in an electrolyte (wet corrosive environment) Battery cell Preferential, accelerated attack of the more active metal (anode) Dissimilar joints located in water (cooling water heat exchangers)
48

48

4.3.1: Galvanic Corrosion

Electrolyte

SS

CS

Electrolyte

CS
49

Mg
49

Inspection Techniques for:

4.3.1 Galvanic Corrosion 4.3.2 Atmospheric Corrosion
-- Visual inspection
-- Ultrasonic thickness testing

50

50

4.3.3: Corrosion Under Insulation (CUI)

Rapid corrosion of carbon steels and lowalloy steels under wet insulation Stainless steels can pit or crack from chloride SCC Sweating equipment or rain water ingress Local corrosion at penetrations in insulation, jacketing at pipe supports, leaking steam tracing where moisture penetrates the insulation
51

51

4.3.3: Corrosion Under Insulation (CUI)

52

Chlorides in insulation worsen CUI Worse downwind of cooling towers Use chloride-free insulation Coat/paint susceptible vessels Make sure weather jacketing is in good condition
52

4.3.3: Corrosion Under Insulation (CUI)

Corrosion techniques: -- visual inspection under insulation -- guided wave UT to find general metal loss -- radiography (RT) of small bore piping -- strip insulation and UT thickness
53

53

4.3.4: Cooling Water Corrosion

Oxygen scavengers, pH control, fluid
54

velocity, temperature monitoring Velocity too low (CS < 3 fps): solids deposit on tube walls and lead to underdeposit pitting Velocity too high (brass > 3 fps): erosion-corrosion Upgrade to Cu-Ni, duplex SS, titanium, epoxy coated tubes
54

4.3.4: Cooling Water Corrosion

Saltwater vs Carbon Steel and Alloys 90 80 70
C orrosion R ate (m py)

60 50 40 30 20 10 0 0 CS 50 100 150 Temperature F Adm. Brass 70-30 Cu-Ni 200 T itanium 250

55

55

4.3.4: Cooling Water Corrosion

Inspection techniques:
-- Visual inspection at tube ends -- Eddy current (EC) inspection -- IRIS inspection of magnetic tubes -- Split sample tube & send to lab -- Monitor water chemistry
56

56

4.3.8: Microbiologically Induced Corrosion (MIC)

Bacteria in cooling water systems, firewater
systems, heat exchangers, pressure vessels, storage tanks, oil and gas pipelines, wells, etc.

Typical of MIC is the creation of thick growths,

also known as tubercles

Tubercles concentrate acids and other waste

products at the metal surface

Underdeposit corrosion, fouling, loss of thermal

conductivity in heat exchangers
57

57

4.3.8: Microbiologically Induced Corrosion (MIC)

Surface pits under tubercles; carbon steel

Pits in cross-section; Type 316 stainless steel

58

58

4.3.8: MIC - Types of Bacteria

Anaerobic Sulfate Reducing Bacteria (ASRB)
Potentially the most common & destructive bacteria group. ASRB reduce sulfates in the water, soil or oil, to H2S which corrodes the steel under the deposit

Acid Producing Bacteria (APB)

Capable of producing organic and inorganic acids as well as producing nutrients for ASRB. APB metabolize sulfur in the water, soil or oil, to sulfurous acid which corrodes steel under the deposit.

Iron-related bacteria (IRB)

Create reactions that support SRB and other MIC bacteria. Form tubercles that concentrate corrosive species

Slime-producing bacteria (SPB)

Live in conjunction with other MIC-producing bacteria (APB, SRB, and IRB). Can from a bridge from aerobic to anaerobic conditions.

59

59

4.3.8: Microbiologically Induced Corrosion (MIC)

Bacteria in cooling water systems, firewater
systems, heat exchangers, pressure vessels, storage tanks, oil and gas pipelines, wells, etc.

Typical of MIC is the creation of thick growths,

also known as tubercles that concentrate acids and waste products at the metal surface

Underdeposit corrosion, fouling, loss of thermal

conductivity in heat exchangers

See NACE TM-0194

60

60

4.3.8: MIC Inspection

Check for fouling of HX bundles, tank & drum
bottoms, firewater & stagnant piping Visually inspect for tubercles Foul-smelling liquids may indicate MIC Confirm MIC with field test kits. Biological Activity Reaction Test (BART) Use biocides

61

61

Section 4.4
High-Temperature Corrosion Above 400F All Industries

62

62

4.4.1: High-Temp Oxidation

Add chromium to increase

oxidation resistance:
CS: 10 mpy rate at 1050F 2-1/4Cr: at 1100F 5-9 Cr: at 1200-1250F 304SS: at 1550F Incoloy 800/H: at 1700F HK, HP: > 1900F
63

63

4.4.1: Oxidation Rates

64

64

4.4.1: High-Temp. Oxidation

Furnace tubes & hangers, burners,

refractory anchors Can be non-uniform on tubes due to flame impingement

65

65

4.4.1: High-Temp. Oxidation

Inspection Techniques:
-- Use TIs & IR thermography while
in service to determine the locations of hot spots -- Visual inspection (look for thick scale) -- UT thickness gauging
66

66

4.4.2: High-Temp Sulfidation

Reaction of metals with
hydrogen sulfide Fe + H2S FeS + H2S FeS + H2 FeS2 + H2

67

Sulfur compounds in crude oil decompose to H2S corrosivity

67

H2S content determines crude

4.4.2: High-Temp Sulfidation

Crude units, vacuum units >1 ppm H2S with no hydrogen Upstream of hydrocrackers and
68

hydrotreaters Extremely sensitive to temperature Add Cr to increase sulfidation resistance

68

4.4.2: High-Temp Sulfidation

CS and low-chrome: above ~500F 5 Cr: above ~ 650F 12Cr and 300-series SS: practically
immune Used for: Cladding, internals, trays

69

69

4.4.2: Sulfidation: Vacuum Column Bottoms Pump

70

70

4.4.2: Sulfidation: Vacuum Column Bottoms Pump

71

71

4.4.2: High-Temp. Sulfidation

Inspection Techniques:
-- TIs & IR thermography while in

service -- Visual inspection -- UT thickness gauging

-- Quest Tru-Tech FTIS of furnace tubes -- PMI (materials identification)
72

72

4.4.2: Sulfidation NACE Publication 34103

73

73

Section 4.5
Environment Assisted
Cracking (SCC) All Industries

74

74

4.5: Stress Corrosion Cracking (SCC)

Depends on environment, material, and temperature. Avoidance measures:
Change metallurgy

75

Stress relief; PWHT Reduce temperature Use coatings Reduce stress Design changes: avoid wet/dry conditions
75

4.5.1: Chloride SCC

76

Aqueous mechanism Requires water with >50 ppm ClAbove ~130F in 300-series SS Above 250-300F in Duplex SS (Alloy 2205) Branched cracking at welds, bends Areas with high residual stress: welds, cold formed bends, bellows, expanded tubes
76

4.5.1: Chloride SCC

Transgranular, surface initiated cracks In sensitized stainless steels, cracking can be intergranular (along grain boundaries)

77

77

Sensitization of 300-Series SS

78

78

4.5.1: Chloride SCC Effect of Temperature and Chloride Concentration

79

79

4.5.1: Chloride SCC

Susceptible: 300-series SS heat
exchanger tubes, vessels, piping, cladding, furnace tubes (on shutdowns) Insulation for 300-series SS tanks, piping, & vessels must be chloride-free May be external due to chlorides in atmosphere, rain water, or insulating materials
80

80

4.5.1: Chloride Content of Some Materials

81

81

4.5.1: Chloride SCC

Inspection Techniques: -- On-line acoustic emission (AE) -- Eddy current (EC) -- Dye penetrant (PT) -- Visual inspection at tube ends -- Shear wave UT to size cracks -- split tubes and inspect ID
82

82

4.5.3: Caustic SCC

83

Steels and nickel alloys are susceptible Must have liquid water w/ caustic >50 ppm Temperature >120F pH 8-14 Tensile stress >25% of YS Non-PWHTd welds, bends are especially susceptible
83

4.5.3: Caustic SCC

Intergranular cracking along grain boundaries

Caustic Cracking in Carbon Steel Caustic Cracking in 316SS Steel 84

84

4.5.3: Caustic SCC

Sources: boiler feed water, injection
to neutralize acids in crude feed and CU overhead

Results in branched cracking Can be intergranular, transgranular,

or mixed

Stress relieve carbon steel or

upgrade to nickel alloys
85

85

4.5.3: Caustic SCC

300-series stainless steels can crack
in caustic above about 230F Due to chlorides in caustic, 300-series SS is generally not used as an upgrade Typical upgrade is Monel above 180-230F
86

86

4.5.3: Caustic SCC

87

87

4.5.3: Caustic SCC of Carbon Steel NACE SP 0403

88

88

4.5.3: Caustic SCC

Inspection Techniques:
-- Visual inspection + -- PT, WFMT -- Shear wave UT to size cracks -- Eddy current (EC) and IRIS of heat exchanger tubes
89

89

Section 5.1.1.1:
Uniform or Localized Loss of Thickness Refining Industry

90

90

5.1.1.1: Amine Corrosion

Amines are used to remove corrosive acid gases (H2S & CO2) from process gases and liquids

Amines can contain acid gases and corrosive degradation products Contaminants include abrasive solids, salts, process chemicals
91

91

5.1.1.1: Amine Corrosion

92

Localized metal loss, especially in high turbulence areas Caused by flashing of acid gases (H2S and CO2) High acid gas loading and salt levels can lead to hydrogen blistering & HIC Can cause SCC in non-post weld heat treated equipment Rich amine is more corrosive
92

5.1.1.1: Amine Corrosion

93

93

5.1.1.1: Amine Corrosion

94

Design for 6 fps max. velocity on rich side, 20 fps max. on lean side Decrease turbulence Clad vessels with 300-series stainless steels Upgrade piping, valves, tees to 304L, 316L stainless steel
94

5.1.1.1: Amine Corrosion

Highly susceptible areas:

Amine regenerators, reboilers, and associated piping where temperature exceeds 200F Rich amine piping High velocity, turbulent streams with acid gas flashing (pump discharge spools, downstream of letdown valves)
95

95

5.1.1.1: Amine Corrosion

Visual inspection Automatic or grid ultrasonic (UT) radiography (RT) for general metal loss Installation of corrosion coupons and electrical resistance (ER) probes Size stress-corrosion cracks with dye penetrant (PT) and wet fluorescent magnetic particle testing (WFMT)
96

96

5.1.1.2: Ammonium Bisulfide Corrosion

97

Aqueous corrosion mechanism where H2S and NH3 exist simultaneously (NH3+H2S = NH4HS) Hydrotreater and FCC overhead systems (especially effluent air coolers and inlet/ outlet piping Amine regenerator overhead systems Sour water stripper overhead systems
97

5.1.1.2: Ammonium Bisulfide Corrosion

Causes erosion-corrosion of carbon steel at velocity >10-20 fps and in turbulent locations Causes deep pitting, corrosion in concentrated streams (NH4HS conc. > 20-30 wt.%)

98

98

5.1.1.2: Ammonium Bisulfide Corrosion

Mitigation:

Reduce velocity and turbulence Clad severe areas w/ 300-series SS Use Incoloy 825 for effluent air cooler
headers & piping
99

99

5.1.1.2: Ammonium Bisulfide Corrosion

Inspection techniques:
-- Locally washed out, thinned areas are easy to miss -- Frequent AUT or grid UT at piping bends, valves, reducers, etc. -- Radiography (RT) -- EC, IRIS of air cooler tubes
100

100

5.1.1.4: HCl Corrosion

101

Tops of atmospheric and vacuum towers Atmospheric & vacuum crude distillation unit overhead streams Acid is the result of hydrolysis of magnesium and calcium chloride salts in crude oils Desalting can reduce HCl formation Corrosion occurs where water condenses Upgrades: Monel trays and cladding
101

5.1.1.4: HCl Corrosion

102

General wasting & washed out appearance Severe thinning with no scale Corrosion rate can exceed an inch per year (1000 mpy) on carbon steel at elevated temperatures Monel has been successful as trays at top of distillation tower and in O/H vapor line
102

5.1.1.4: HCl Corrosion

103

103

5.1.1.4: HCl Corrosion

Inspection techniques: -- Visual inspection of trays and O/H lines

-- Automatic UT or grid UT, radiography (RT) of overhead streams and known trouble spots -- Corrosion probes (ER, FSM) and coupons -- Hydrogen flux, Fe++, Cl- monitoring
104

104

5.1.1.5: H2/H2S Corrosion

105

Occurs in the presence of hot H2 and H2S simultaneously Corrosion rate depends on temperature and partial pressure of H2S Usually uniform metal loss H2 results in porous non-protective iron sulfide scale
105

5.1.1.5: H2/H2S Corrosion

CS-9Cr: significant corrosion
106

> 500-550F 12 Cr steel (410SS): > 700-800F 300-series SS: > 900-1000F Hydrotreaters, FCCs 300-series SS for reactor cladding, internals, and hot piping (> 750F)
106

5.1.1.5: H2/H2S Corrosion Corrosion Rates

107

107

5.1.1.5: H2/H2S Corrosion

Unlike high-temperature sulfidation in crude units, cokers, vac units (in the absence of hyrogen) High-Temp Sulfidation: additions of Cr alone add corrosion resistance H2/H2S Corrosion: Cr alone is not beneficial. Requires upgrade to 304, 316 SS
108

108

5.1.1.5: H2/H2S Corrosion

109

109

5.1.1.5: H2/H2S Corrosion

Inspection Techniques:
-- Visual inspection +
-- Ultrasonic thickness (UT) -- Radiography (RT)

110

110

5.1.2.3: SCC Resistant Materials NACE MR 0103

111

111

5.1.1.11: Sulfuric Acid Corrosion

Sulfuric acid alkylation plants Can result in washout and severe
112

thinning of carbon steel CS cannot be used for weak acid Refineries use carbon steel extensively for strong acid concentrations (95100%) at near ambient temperatures Can require large corrosion allowances
112

5.1.1.11: Sulfuric Acid Corrosion

Corrosion is velocity and turbulence
related localized

Velocity must be <3 fps for CS CS corrosion rate < 50 mpy if acid
concentration > 65%, T <125F, velocity < 3 fps 316SS for thin-wall piping
113

Alloy 20 (29Cr-20Ni-3Mo) for pumps;

113

5.1.1.11: Sulfuric Acid Corrosion

Corrosion of Carbon Steel

114

114

5.1.1.11: Sulfuric Acid Corrosion

Corrosion of Alloy 20
115

115

5.1.1.11: Sulfuric Acid Corrosion Inspection Techniques:

-- Automatic UT or grid UT, RT (esp. in hot or turbulent areas) -- Visual inspection -- Corrosion probes and coupons
116

116

Section 5.1.2
Environment-Assisted Cracking Refining Industry

117

117

5.1.2.3: Wet H2S Cracking

Hydrogen Induced Cracking (HIC)
-- hydrogen charging in the presence of sulfur

Stress-oriented HIC (SOHIC) Hydrogen blistering Sulfide Stress Cracking (SSC)

-- cracking of hard welds
118

118

5.1.2.3: Wet H2S Cracking

119

119

5.1.2.3: Hydrogen Induced Cracking (HIC)

Occurs mostly in carbon steel plate and thick-walled piping Where sour water is present:

-- overhead equipment
-- separators & K.O. drums -- heat exchanger channels & shells

120

Mostly at ambient temperature, up to about 150F

120

Wet H2S Cracking in Distillation Unit Overhead Systems

121

121

Examples of Hydrogen Blistering

122

122

Hydrogen Induced Cracking and Blistering

Sulfur poisons the recombination reaction Ho + H o H2 gas

Hydrogen atoms are absorbed into the steel and form internal hydrogen blisters and cracks
123

123

HIC and Blistering

124

124

5.1.2.3: Hydrogen Blistering

Blisters on the ID surface of affected carbon steel

125

125

5.1.2.3: Wet H2S Cracking -Special Precautions

Blistered steel is irreversibly damaged If repairs are to be made to damaged steel, expect the steel to be hydrogensaturated and potentially embrittled Prior to repairs: consider hydrogen bake out at > 400F

126

126

5.1.2.3: Sulfide Stress Cracking

Cracking of hard metals and weld HAZs Maintain weld hardness below BHN
127

200 for CS, BHN 215 for low-alloy steels Valve trim, bolting <Rc 22, YS <90 ksi welds, 12Cr trim, B7 bolting susceptible Refer to NACE MR-0175 Use B7M bolts
127

5.1.2.3: Sulfide Stress Cracking (SSC)

128

128

5.1.2.3: Wet H2S Cracking

FCC Units -- fractionator overhead equipment, gas absorbers, compressors Hydrocrackers & Hydrotreaters valve stems & trim, gas absorbers and compressors, cold separators Sour water strippers upper sections of columns, overhead drums & exchangers Crude unit overhead equipment Amine, acid gas units columns, drums, exchanger shells
129

129

5.1.2.3: Avoiding Wet H2S Cracking in Welds

130

PWHT welds to reduce weld hardness and residual stress BHN 200 max. for carbon steel; BHN 215 max. for low-alloy steels PWHT carbon steel at 1100-1200F (1 hr./inch, 1 hr. min.) PWHT 1-1/4Cr & 2-1/4Cr steel at 1300-1375F 130

5.1.2.3: Wet H2S Cracking

Inspection: -- Visual inspection for blisters, cracks -- Straight beam and shear wave UT can find internal blisters -- Inspect welds, HAZs for SSC with WFMT (no PT -- cracks can be tight) -- Alternating current magnetic flux leakage (ACFM) -- Radiography (RT)
131

131

5.1.3.1: High-Temperature Hydrogen Attack (HTHA)

In hot high-pressure hydrogen CS immune to ~450F, depends on H2 pp Cr & Mo increase HTHA resistance
132

(1-1/4Cr-1/2Mo, 2-1/4Cr-1Mo, 3Cr-1Mo) Causes internal methane bubbles and fissures Reduces impact toughness; causes blisters Can be very difficult to find; advanced inspection techniques HTHA predicted by API 941 (Nelson Curves)
132

5.1.3.1: High Temperature Hydrogen Attack

Hydrogen in contact with steel at high temperature leads to decarburization and subsequent methane formation:
C(Fe) + 4H CH4 (gas)

Methane that forms internally in steels, result in fissures from high-pressure bubbles on grain boundaries Fissures result loss of fracture toughness, and potentially catastrophic brittle fractures

133

133

5.1.3.1: High-Temperature Hydrogen Attack

Hydrogen Attack Formation of Microfissures

134

134

5.1.3.1: High-Temperature Hydrogen Attack in Carbon Steel

135

135

5.1.3.1: High-Temperature Hydrogen Attack API 941

136

136

5.1.2.1: API 941 Limits for HTHA

137

137

5.1.3.1: HTHA Prevention

Cr & Mo additions improve resistance to HTHA New equipment should be fabricated from HTHAresistant materials for the design operating pressures and temperatures (according to API 941 guidelines) Existing equipment that does not meet API 941 guidelines should be removed from service or subject to concentrated frequent inspection HTHA causes a loss in strength and fracture toughness and can result in brittle fracture. Equipment containing HTHA may not be fit for service
138

138

5.1.3.1: HTHA Inspection

139

Very difficult to find incipient attack May be more likely at spec breaks, in dead legs, in welds, HAZs Must have an idea of where to look UT velocity ratio and backscatter Focused beam shear wave If in doubt, take a boat sample or replace suspected piping; downgrade PVs
139

Questions ?
Please feel free to contact me:

Charlie Buscemi [email protected] Mobile: (504) 650-2427 Office: (504) 889-8440

140