Scribd
Upload
45 views12 pages

Shear Design of Beams: CE 470 - Steel Design Class

This document discusses shear design of beams. It covers shear strength, which includes shear yielding and shear buckling. Equations are provided for calculating the nominal shear strength based on the steel yield strength and web area. Buckling is dependent on the web height-to-thickness ratio. Block shear failure at beam ends is also discussed, where both shear and tension must be considered. An example calculation is provided to determine the maximum reaction for a beam based on block shear strength.

Uploaded by

Anu Parthee
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
45 views12 pages

Shear Design of Beams: CE 470 - Steel Design Class

This document discusses shear design of beams. It covers shear strength, which includes shear yielding and shear buckling. Equations are provided for calculating the nominal shear strength based on the steel yield strength and web area. Buckling is dependent on the web height-to-thickness ratio. Block shear failure at beam ends is also discussed, where both shear and tension must be considered. An example calculation is provided to determine the maximum reaction for a beam based on block shear strength.

Uploaded by

Anu Parthee
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 12

Shear Design of Beams

CE 470 - Steel Design Class


By, Amit H. Varma

Shear Strength

Beam shear strength is covered in Chapter G of the AISC specifications. Both rolled shapes and welded built-up shapes are covered. Rolled shapes is the focus here. Built-up shapes, commonly referred to as plate-girders are beyond the scope of our course. Consider the behavior of beams in shear

Shear Strength

The web will completely yield long before the flanges begin to yield. Because of this, yielding of the web represents one of the shear limit states. Taking the shear yield stress as 60% of the tensile yield stress. V f v n 0.6 Fy Aw Vn 0.6 Fy Aw This will be the nominal strength in shear provided there is no shear buckling of the web.

Shear buckling of the web depends on its h/tw ratio. If the ratio is too large, then then web can buckle in shear elastically or inelastically.

Shear Buckling
kv 5 for unstiffened webs with h / t w 260 5 kv 5 for stiffened webs 2 (a / h)

Shear yielding

Elastic shear buckling

Shear Design Equations

Shear Design Equations

Shear Design Equations

Block Shear Failure of Beam


Block shear failure was considered earlier in tension member connections. To facilitate the connections of beams to other beams so that the top flanges are at the same elevation, a short length of the top flange of one of the beams may be cut away, or coped. If a coped beam is connected with bolts as shown, segment ABC will tend to tear out.

Block shear failure of beam ends

The applied load in the case of the beam will be the vertical reaction, so shear will occur along line AB and there will be tension along BC. Thus, the block shear strength will be a limiting value of the reaction. Failure is assumed to occurred by rupture (fracture) on the tension area and rupture or yielding on the shear area. Rn = 0.6 Fu Anv + Ubs Fu Ant 0.6 Fy Agv + Ubs Fu Ant Where, phi =0.75

Example

Determine the maximum reaction, based on block shear, that can be resisted by the beam shown below. Treat the bolt end distance of 1.25 in. as standard.

The effective hole diameter is 3/4 + 1/8 = 7/8 in. The shear areas are: Agv = tw (2+3+3+3) = 0.30 (11) = 3.3 in2 Anv = 0.300 [11 -3.5 (7/8)] = 2.381 in2

Block shear example


The net tension area is: Ant = 0.300 [1.25 - 1/2 (7/8) ] = 0.2348 in2 Since the block shear will occur in a coped beam with standard bolt end distance Ubs = 1.0. Rn = 0.6 Fu Anv + Fu Ant = 108.7 kips

With an upper limit of Rn = 0.6 Fy Agv + Fu Ant = 144.5 kips

Therefore, nominal block shear strength = 108.7 kips Factored block shear strength for design = 0.75 x 108.7 = 81.5 kips.

You might also like