Scribd
Upload
49 views

Chapter 1 Material

The document discusses the classification and mechanical properties of construction materials. It describes how construction materials can be classified based on their physical nature as solid, liquid, or gaseous, and based on their mode of manufacture as naturally occurring, industrially produced, or produced on site. It focuses on the mechanical properties of materials, including stresses, strains, strength, and deformation. Finally, it outlines different types of mechanical tests used to measure mechanical properties, including tension, compression, shear, bending, and torsion tests, as well as static, dynamic, wear, long-time, fatigue, destructive, and non-destructive tests.

Uploaded by

Kiflom Birhane
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
49 views

Chapter 1 Material

The document discusses the classification and mechanical properties of construction materials. It describes how construction materials can be classified based on their physical nature as solid, liquid, or gaseous, and based on their mode of manufacture as naturally occurring, industrially produced, or produced on site. It focuses on the mechanical properties of materials, including stresses, strains, strength, and deformation. Finally, it outlines different types of mechanical tests used to measure mechanical properties, including tension, compression, shear, bending, and torsion tests, as well as static, dynamic, wear, long-time, fatigue, destructive, and non-destructive tests.

Uploaded by

Kiflom Birhane
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

1.

1.1

Introduction
Classification of Construction Materials

Construction materials can be classified into: I) Metallic and Non-metallic a. Non-metallic - Cementing materials - Concrete - Timber - Stone - Plastics - Ceramics b. Metallic - Ferrous Wrought iron Cast iron Steel - Non Ferrous Aluminium Copper Lead Zinc Based on their physical Nature: a) Solid b) Liquid c) Gaseous III) Based on their mode of manufacture a) Naturally occurring materials b) Industrially produced materials c) Materials produced at construction site 1.2 Properties of Materials a) Physical properties Density and specific gravity Mechanical properties Thermal properties Acoustical properties

II)

_____________________________________________________________________ 1

Eyob Yilma, Construction Technology Department, NCTTE

b)

Chemical properties Corrosion

Here only the mechanical properties are dealt with since they have a great practical significance in Civil Engineering. 1.2.1 Mechanical Properties When forces are applied to a solid body, two results are produced: 1) Internal resisting forces 2) Deformation The internal forces and deformations are called stresses and strains respectively. Depending up on the arrangement and direction of the external forces, the stress produced may be: a) b) c) d) e) f) Deformation: a) Elastic if it recovers when the external force is released b) Plastic if it fails to recover when the external force is released If a material is capable to carry its own weight and any applied load, it is assumed to be strong material. This way is that the strength of the material is determined. When a material is said to be strong it is its strength in tension or compression that is usually referred to, but it is often necessary to know its strength in shear and torsion as well. 1.3 Tests for Mechanical Properties Tensile stress Compressive stress Shearing stress Bending stress Torsional stress Combinations of the above stresses

Selection of material for a particular structural application depends on its mechanical properties. There are standard mechanical tests to measure these properties. Mechanical tests are used to examine the performance of materials under the action of external forces. _____________________________________________________________________ 2

Eyob Yilma, Construction Technology Department, NCTTE

1.3.1 I)

Classification of Mechanical Tests With reference to the direction of the external forces a) Tension test b) Compression test c) Shear test d) Bending test e) Torsion test

II)

With reference to the rate and duration of the load application a) Static Tests: these are made with gradually increasing load, such as ordinary tests in tension, compression etc. b) Dynamic test: these are made with suddenly applied loads, as by falling weight c) Wear tests: these are made to determine resistance to abrasion and impact, as in the case of paving materials d) Long-time tests: there are made with loads applied to the object under test for a long period of time. They are used for materials such as concrete. e) Fatigue test: these are made with fluctuating stresses repeated a large number of times

III)

With reference to the effect of the test on the specimen a) Destructive tests: Under these test methods, the specimens are either crushed or ruptured and made useless at the end of the tests b) Non-destructive tests: These are usually used to test the strength of members of existing structures without affecting their performance.

_____________________________________________________________________ 3

Eyob Yilma, Construction Technology Department, NCTTE

You might also like