Scribd
Upload
3K views2 pages

RSL - Radio Signaling Link Disconnected

This alarm occurs when the radio signaling link (RSL) between the BSC and the TRX fails. It causes the TRX to shut down its power amplifier, disrupting ongoing services on that TRX. If the failed TRX is handling the BCCH, it disrupts services for the entire cell. The system will trigger a BCCH switchover if not cleared within two minutes. Possible causes include issues with the CPRI port, transmission between the BTS and BSC, or failures of the RF unit or TRX board.

Uploaded by

Aguiar110374
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3K views2 pages

RSL - Radio Signaling Link Disconnected

This alarm occurs when the radio signaling link (RSL) between the BSC and the TRX fails. It causes the TRX to shut down its power amplifier, disrupting ongoing services on that TRX. If the failed TRX is handling the BCCH, it disrupts services for the entire cell. The system will trigger a BCCH switchover if not cleared within two minutes. Possible causes include issues with the CPRI port, transmission between the BTS and BSC, or failures of the RF unit or TRX board.

Uploaded by

Aguiar110374
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

ALM-28006 Radio Signaling Link Disconnected

Description This alarm is reported when the radio signaling link (RSL) between the BSC and the TRX fails. Parameters Parameter Name Cabinet n Subrack n Slot n Carrier n Impact on the System Alarm Severity Major Alarm Impact The TRX automatically shuts down the power amplifier (PA), and the ongoing services carried on the TRX are disrupted. If the TRX is the BCCH TRX, the ongoing services of the cell holding the TRX are disrupted. Parameter Desciption Cabinet number of the faulty board Subrack number of the faulty board Slot number of the faulty board Faulty carrier number

System Actions If this alarm is generated on the BCCH TRX and if the TRX aiding function is enabled, the BCCH switchover is triggered in the case that this alarm is not cleared within two minutes. Possible Causes

Procedure 1. Check the CPRI port on the M2000. a. Check whether all TRXs on the RF unit report the following alarm on the M2000. 28006 Radio Signaling Link Disconnected Y => All TRXs on the RF unit report the alarm. Go to sub-step b. N => Not all TRXs on the TRX board report the alarm. Go to sub-step d. b. Check for the correlated alarm on the CPRI port of the BTS on the M2000. 26230 BBU CPRI Optical Module Fault 26231 BBU CPRI Optical Module or Electrical Port Not Ready 26232 BBU Optical Module Transmit/Receive Fault 26233 BBU CPRI Optical Interface Performance Degraded 26234 BBU CPRI Interface Error 26262 External Clock Reference Problem 26264 System Clock Unlocked 26235 RF Unit Maintenance Link Failure Y => The correlated alarm exists. Go to sub-step c. N => The correlated alarm does not exist. Go to sub-step d. c. Clear the correlated alarm according to the relevant handling suggestions. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Go to sub-step d.

d. Obtain the TRX index. Run the MML command RST TRX to reset the faulty TRX on the Web LMT. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Go to step 2. 2. Check the transmission between the BSC and the BTS. a. Check for the correlated alarms on the transmission between the BTS and the BSC on the M2000. 25880 Ethernet Link Fault 25881 MAC Excessive Frame Error Rate E1/T1-Correlated Alarms or PPP/MLPPP-Correlated Alarms Y => The correlated alarm exists. Go to sub-step b. N => The correlated alarm does not exist. Go to step 3. b. Clear the correlated alarm according to the relevant handling suggestions. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Go to step 3. 3. Replace the main control board or the TRX board. a. Replace the RF unit. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Go to sub-step b. b. Run the MML command RST BTSBRD to reset the GTMU. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Go to sub-step c. c. Replace the main control board. Check whether the alarm is cleared. Y => The alarm is cleared. No further action is required. N => The alarm is not cleared. Reinstall the original board. Contact Huawei Customer Service Center.

You might also like