Product Bulletin

62.1:DVC6000 D102758X012 December 2010

DVC6000 Digital Valve Controllers

Fisherr FIELDVUEt DVC6000 Digital Valve Controllers

FIELDVUE DVC6000 digital valve controllers (figures 1 and 2) are communicating, microprocessorbased currenttopneumatic instruments. In addition to the traditional function of converting a current signal to a valveposition pressure signal, DVC6000 digital valve controllers, using HARTr communications protocol, give easy access to information critical to process operation. This can be done using a Field Communicator at the valve or at a field junction box, or by using a personal computer or a system console within the control room. Using HART communication protocol, information can be integrated into a control system or received on a single loop basis. DVC6000 digital valve controllers can be used on single or doubleacting actuators. The digital valve controller receives feedback of the valve travel position plus supply and actuator pneumatic pressure. This allows the instrument to diagnose not only itself, but also the valve and actuator to which it is mounted. This provides you with very cost effective maintenance information, as the required maintenance can be performed on the instrument and valve when there really is a need. Wiring is economical because DVC6000 digital valve controllers use twowire 4 to 20 mA loop power. This provides for low cost replacement of existing analog instrumentation. The twowire design avoids the high cost of running separate power and signal wiring.

W91311 W7957 / IL

Figure 1. FIELDVUE DVC6010 Digital Valve Controller Mounted on a SlidingStem Valve Actuator

Figure 2. FIELDVUE DVC6010 Digital Valve Controller Mounted on Fisher 585C Piston Actuator

www.Fisher.com

Product Bulletin

DVC6000 Digital Valve Controllers

Specifications
Available Configurations ValveMounted Instrument: DVC6010: Slidingstem applications DVC6020: Rotary applications and longstroke slidingstem applications DVC6030: Quarterturn rotary applications RemoteMounted Instrument(1): DVC6005: Base unit for 2 inch pipestand or wall mounting DVC6015: Feedback unit for slidingstem applications DVC6025: Feedback unit for rotary or longstroke slidingstem applications DVC6035: Feedback unit for quarterturn rotary applications DVC6000 digital valve controllers can be mounted on Fisher and other manufacturers rotary and slidingstem actuators. Input Signal PointtoPoint:. Analog Input Signal: 420 mA DC, nominal; split ranging available Minimum Voltage Available at Instrument Terminals must be 10.5 VDC for analog control, 11 VDC for HART communication (see instrument instruction manual for details) Minimum Control Current: 4.0 mA Minimum Current w/o Microprocessor Restart: 3.5 mA Maximum Voltage: 30 VDC Overcurrent Protection: Input circuitry limits current to prevent internal damage Reverse Polarity Protection: No damage occurs from reversal of loop current Multidrop:. Instrument Power: 11 to 30 VDC at approximately 8 mA Reverse Polarity Protection: No damage occurs from reversal of loop current Output Signal Pneumatic signal as required by the actuator, up to 95% of supply pressure Minimum Span: 0.4 bar (6 psig) Maximum Span: 9.5 bar (140 psig) Action: J Double, J Single Direct, and J Single Reverse
continued

62.1:DVC6000 December 2010

Supply Pressure(2) Minimum Recommended: 0.3 bar (5 psig) higher than maximum actuator requirements Maximum: 10.0 bar (145 psig) or maximum pressure rating of the actuator, whichever is lower Medium: Air or Natural Gas(7) Air: Supply pressure must be clean, dry air that meets the requirements of ISA Standard 7.0.01. A maximum 40 micrometer particle size in the air system is acceptable. Further filtration down to 5 micrometer particle size is recommended. Lubricant content is not to exceed 1 ppm weight (w/w) or volume (v/v) basis. Condensation in the air supply should be minimized Natural Gas: Natural gas must be clean, dry, oilfree, and noncorrosive. H2S content should not exceed 20 ppm.

SteadyState Air Consumption(3)(4) Standard Relay: At 1.4 bar (20 psig) supply pressure: Less than 0.38 normal m3/hr (14 scfh) At 5.5 bar (80 psig) supply pressure: Less than 1.3 normal m3/hr (49 scfh) Low Bleed Relay(5): At 1.4 bar (20 psig) supply pressure: Average value 0.056 normal m3/hr (2.1 scfh) At 5.5 bar (80 psig) supply pressure: Average value 0.184 normal m3/hr (6.9 scfh)

Maximum Output Capacity(3)(4) At 1.4 bar (20 psig) supply pressure: 10.0 normal m3/hr (375 scfh) At 5.5 bar (80 psig) supply pressure: 29.5 normal m3/hr (1100 scfh)

Independent Linearity(6) 0.50% of output span

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

Other Classifications/Certifications TIISJapan KISCOKorea Industrial Safety Corp. GOSTRRussian GOSTR FSETANRussian Federal Service of Technological, Ecological and Nuclear Inspectorate Contact your Emerson Process Management sales office for classification/certification specific information Connections

Specifications (continued)
Electromagnetic Compatibility Meets EN 613261 (First Edition) ImmunityIndustrial locations per Table 2 of the EN 613261 standard. Performance is shown in table 2 below. EmissionsClass A ISM equipment rating: Group 1, Class A Lightning and Surge ProtectionThe degree of immunity to lightning is specified as Surge immunity in table 2. For additional surge protection commercially available transient protection devices can be used. IEC 61010 Compliance Requirements (ValveMounted Instruments Only) Power Source: The loop current must be derived from a separated extralow voltage (SELV) power source Environmental Conditions: Installation Category I Electrical Classification Hazardous Area: CSAIntrinsically Safe, Explosionproof, Division 2, Dust Ignitionproof FMIntrinsically Safe, Explosionproof, Nonincendive, Dust Ignitionproof ATEXIntrinsically Safe, Flameproof, Type n IECExIntrinsically Safe, Flameproof, Type n NEPSIIntrinsically Safe, Flameproof INMETROIntrinsically Safe, Flameproof, Type n Refer to tables 3, 4, 5, 6, 7, and 8. Electrical Housing: CSAType 4X, IP66 FMNEMA 4X ATEXIP66 IECExIP66 NEPSIIP66 INMETROIP66
continued

Supply Pressure: 1/4 NPT internal and integral pad for mounting 67CFR regulator Output Pressure: 1/4 NPT internal Tubing: 3/8inch recommended Vent (pipeaway): 3/8 NPT internal Electrical: 1/2 NPT internal conduit connection Vibration Testing Method Tested per ANSI/ISAS75.13.01 Section 5.3.5. A resonant frequency search is performed on all three axes. The instrument is subjected to the ISA specified 1/2 hour endurance test at each major resonance, plus an additional two million cycles. Humidity Limits 0 to 100% condensing relative humidity with minimal zero or span shifts Input Impedance The input impedance of the DVC6000 active electronic circuit is not purely resistive. For comparison to resistive load specifications, an equivalent impedance of 550 ohms may be used. This value corresponds to 11V @ 20 mA. Operating Ambient Temperature Limits(2)(8) 40 to 85_C (40 to 185_F) for most approved valvemounted instruments 60 to 125_C (76 to 257_F) for remotemounted feedback units 52 to 85_C (62 to 185_F) for valvemounted instruments utilizing the Extreme Temperature option (fluorosilicone elastomers)

Product Bulletin

DVC6000 Digital Valve Controllers

Specifications (continued)
Construction Materials Housing, module base and terminal box: ASTM B85 A03600 low copper aluminum alloy (standard) CF8M (cast 316 stainless steel) (optional for valvemounted instruments only) Cover: Thermoplastic polyester Elastomers. Standard: Nitrile Optional: Fluorosilicone Stem/Shaft Travel Linear Actuators with rated travel between 6.35 mm (0.25 inch) and 606 mm (23.375 inches) Rotary Actuators with rated travel between 50 degrees and 180 degrees

62.1:DVC6000 December 2010

of moisture that may be introduced via the instrument air supply. Weight ValveMounted Instruments. Aluminum: 3.5 kg (7.7 lbs) Stainless steel: 7.7 kg (17 lbs) RemoteMounted Instruments. DVC6005 Base Unit: 4.1 kg (9 lbs) DVC6015 Feedback Unit: 1.3 kg (2.9 lbs) DVC6025 Feedback Unit: 1.4 kg (3.1 lbs) DVC6035 Feedback Unit: 0.9 kg (2.0 lbs) Options
J Supply and output pressure gauges or J Tire valves J Integral mounted filter regulator J Stainless steel housing, module base and J LowBleed Relay, J Extreme Temperature J Remote Mount J Inline 10 micrometer air filter J Safety Instrumented System (SIS) Solutions J Safety Related Nuclear Applications J Natural Gas Certified J Feedback Assembly PTFE

terminal box (valvemounted instruments only)

Mounting Designed for direct actuator mounting or remote pipestand or wall mounting. Mounting the instrument vertically, with the vent at the bottom of the assembly, or horizontally, with the vent pointing down, is recommended to allow drainage

Sleeve Protective Kit for aluminum units in saltwater or particulate environments

NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1 Process Instrument Terminology. 1. 3conductor shielded cable, 22 AWG minimum wire size, is required for connection between base unit and feedback unit. Pneumatic tubing between base unit output connection and actuator has been tested to 15 meters (50 feet) maximum without performance degradation. 2. The pressure/temperature limits in this document and any other applicable code or standard should not be exceeded. 3. Normal m3/hour Normal cubic meters per hour at 0_C and 1.01325 bar, absolute. Scfh Standard cubic feet per hour at 60_F and 14.7 psia. 4. Values at 1.4 bar (20 psig) based on a singleacting direct relay; values at 5.5 bar (80 psig) based on doubleacting relay. 5. The Low Bleed Relay is offered as standard relay for DVC6000 SIS, used for On/Off applications. 6. Typical value. Not applicable for DVC6020 digital valve controllers in longstroke applications or remotemounted DVC6005 digital valve controllers with long pneumatic tubing lengths. 7. Gas Certified DVC6000 digital valve controllers are FM, ATEX, IECEx, INMETRO, and CSA Single Seal approved for use with natural gas as the supply medium. 8. Temperature limits vary based on hazardous area approval.

Features
D Improved ControlTwoway digital communications give you current valve conditions. You can rely on this realtime information to make sound process management decisions. By analyzing valve dynamics through ValveLinkt software you can identify control areas needing improvement and maintain a high level of system performance.

D Enhanced SafetyYou can check instrument and valve operation and keep the process running smoothly and safely from a remote location. Access is possible at a field junction box, marshalling panel, or within the safety of the control room using either a Field Communicator, a notebook PC, or a system workstation. Your exposure to hazardous environments is minimized and you can avoid having to access hardtoreach valve locations. D Hardware SavingsDVC6000 digital valve controllers, when used in an integrated system, allow you to realize significant hardware and installation cost savings by replacing other devices in the process loop, such as positioners and limit switches, with a FIELDVUE digital valve controller.

D Environmental ProtectionYou can avoid additional field wiring by connecting a leak detector or limit switch to the auxiliary terminals in the DVC6000 digital valve controller. In this way, the instrument will issue an alert if limits are exceeded.

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

Table 1. FIELDVUE DVC6000 Diagnostic Level Capabilities

CAPABILITY Auto Calibration Custom Characterization Burst Communication Alerts Step Response, Drive Signal Test & Dynamic Error Band, Valve Signature Performance Tuner Travel Control Pressure Fallback Performance Diagnostics Partial Stroke Testing Lead/Lag Input Filter(2)
1. Refer to Bulletin 62.1:DVC6000 SIS for information on DVC6000 digital valve controllers for Safety Instrumented System (SIS) Solutions. 2. Refer to brochure part # D351146X012 / D351146X412 for information on Fisher optimized digital valves for compressor antisurge applications.

DIAGNOSTIC LEVEL AC n n HC n n n n AD n n n n n n n PD n n n n n n n n n SIS(1) n n n n n n ODV n n n n n n n n n n

D Built to SurviveFieldtough DVC6000 digital valve controllers have fully encapsulated printed wiring boards that resist the effects of vibration, temperature, and corrosive atmospheres. A separate weathertight field wiring terminal box isolates fieldwiring connections from other areas of the instrument.

This module contains the critical submodules so component removal is quick and simple. D Travel Control Pressure FallbackValve position feedback is critical to the operation of a digital valve controller. Without this feedback, the control valve assembly traditionally goes to its fail safe position. DVC6000 digital valve controllers can detect position feedback problems caused by a travel sensor failure or linkage failure and continue to operate in pressure control mode. If a problem with the valve position feedback is detected, the instrument will automatically disable the travel sensor, send an alert, and control its output pressure much like an I/P transducer. This allows the valve assembly to continue to operate with reduced accuracy until maintenance can be scheduled.

D Increased UptimeWith the selfdiagnostic capability of the DVC6000, you can answer questions about a valves performance, without pulling the valve from the line. You can run diagnostics (I/P and relay integrity, travel deviation, and online friction and deadband analysis and trending) while the valve is in service and operating. You can also compare the present valve/actuator signature (bench set, seat load, friction, etc.) against previously stored signatures to discover performance changes, before they cause process control problems.

D Faster CommissioningThe twoway communication capability allows you to quickly commission loops by remotely identifying each instrument, verifying its calibration, reviewing stored maintenance notes, and more.

Diagnostics
DVC6000 digital valve controllers are packed with userconfigurable alerts and alarms. When integrated with a HART communicating system, these flags provide realtime notification of current and potential valve and instrument problems. With ValveLink software, tests can be performed to identify problems with the entire control valve assembly. Diagnostic capabilities available are Performance Diagnostics (PD) and Advanced Diagnostics (AD). Refer to table 1 for details on the capabilities of each diagnostic level.

D Easy MaintenanceThe DVC6000 is modular in design. The module base can be removed from the instrument housing without disconnecting the field wiring, pneumatic connections or stem linkages.

Product Bulletin

DVC6000 Digital Valve Controllers

62.1:DVC6000 December 2010

ERROR (RED)

WARNING (YELLOW) NO CONDITIONS HAVE BEEN DETECTED (GREEN)

Figure 3. Red/Yellow/Green Condition Indicators, Shown in ValveLink Software

Performance Diagnostics Performance Diagnostics enables the use of diagnostics while the valve is in service and operating. D Red/Yellow/Green Condition Indicator (see figure 3) D I/P and Relay Integrity Diagnostic D Travel Deviation Diagnostic D OneButton Diagnostic The OneButton Diagnostic, (shown in figure 4), is a 20 second sweep which runs the I/P and Relay Integrity, Relay Adjustment, Travel Deviation, Supply Pressure, and Air Mass Flow Performance Diagnostic tests. When the sweep is complete, ValveLink software will show any errors, possible causes, and recommended actions to resolve the error(s). D OnLine/InService Friction and Deadband Analysis (see figure 5) D Friction and Deadband Trending While all diagnostics can be run while the valve is inline, only the Performance Diagnostics can be performed while the valve is in service and operating.

Advanced Diagnostics Advanced Diagnostics include the following dynamic scan tests: D Valve Signature (see figure 6) D Dynamic Error Band D Instrument Drive Signal These diagnostic scans vary the positioner set point at a controlled rate and plot valve operation to determine valve dynamic performance. The valve signature test allows you to determine the valve/actuator friction, bench set, spring rate, and seat load. The Dynamic Error Band test is a combination of hysteresis and deadband plus slewing. Hysteresis and deadband are static measurements. However, because the valve is moving, a dynamic error, or slewing error is introduced. Dynamic scan tests give a better indication of how the valve will operate under process conditions which are dynamic, not static.

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

ERROR TYPE

RECOMMENDED ACTION

E1035

ERROR DETECTED (RED)

POSSIBLE CAUSE

E1036

Figure 4. OneButton SweepAir Mass Flow Diagnostic

W7468/IL

Figure 5. Valve Friction and Deadband Analysis

Figure 6. The Valve Signature Display

The Step Response Test checks the valve assemblies response to a changing input signal and plots travel versus time. The end results of this test allow you to evaluate the dynamic performance of the valve. The Performance Step Test (25 preconfigured points) provides a standardized step

test with which to evaluate your valve performance. It utilizes small, medium and large changes. Advanced Diagnostics are performed with ValveLink software. The valve must be out of service for Advanced Diagnostics to be performed.

Product Bulletin

DVC6000 Digital Valve Controllers

DISTRIBUTED CONTROL SYSTEM (DCS)

62.1:DVC6000 December 2010

MODBUS

VALVELINK SOFTWARE

FIELD TERMINATION ASSEMBLY (FTA) RS232TORS485 CONVERTER 420 mA HART

CONTROL SYSTEM I/O 420 mA + HART

HART MULTIPLEXER

W8082 1 / IL

Figure 7. Integrate Information from the Digital Valve Controller into a NonHART Compatible Control System With ValveLink Softwares Modbus Interface

Integration
D NonHART SystemsBecause DVC6000 digital valve controllers operate with a traditional 4 to 20 mA control signal, they directly replace older analog instruments. Microprocessorbased electronics provide improved performance along with repeatable and reliable configuration and calibration. D Modbus with ValveLink software and HART multiplexersHART communication allows you to extract more value from DVC6000 digital valve controllers beyond their inherent improved performance. When integrated into a multiplexer network and using ValveLink software, the device

and valve information is realtime. From the safety of a control room, multiple instruments can be monitored for alerts and alarms. Additionally, tasks such as configuration, calibration and diagnostic testing do not require special trips to the field. ValveLink software can communicate via Modbus to the distributed control system (DCS) to provide critical information such as valve travel alerts and alarms (figure 7). D Integrated Control SystemA control system with HART communication capabilities has the ability to directly gather information from DVC6000 digital valve controllers. Information such as valve travel, alerts and alarms can be seamlessly accessed to provide a view into the field device from the safety of the control room.

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

+0.5 V

ANALOG SIGNAL

0.5 V 1200 Hz , 1, 2200 Hz , 0,

AVERAGE CURRENT CHANGE DURING COMMUNICATION = 0

A6174/IL

Figure 8. HART Frequency Shift Keying Technique

Communication
HART Protocol Overview The HART (Highway Addressable Remote Transducer) protocol gives field devices the capability of communicating instrument and process data digitally. This digital communication occurs over the same twowire loop that provides the 4 to 20 mA process control signal, without disrupting the process signal (figure 8). In this way, the analog process signal, with its faster response, can be used for control. At the same time, the HART digital communication gives access to calibration, configuration, diagnostic, maintenance, and additional process data. The protocol provides total system integration via a host device. The HART protocol gives you the capability of multidropping, where you can network several devices to a single communications line. This process is well suited for remote applications such as pipelines, custody transfer sites, and tank farms. Field Communicator You can perform configuration and calibration at the valve or anywhere on the twowire loop via a Field Communicator (see figure 9). Powerful tools such as Setup Wizard and Auto Travel Calibration automate the tasks of commissioning DVC6000 digital valve controllers. These automation tools not only save time, but also provide accurate and repeatable results. ValveLink Software ValveLink software is a WindowsRbased software package that allows easy access to the information available from DVC6000 digital valve controllers.
Figure 9. Perform Configuration and Calibration at the Valve or Anywhere on the 4 to 20 mA Loop with the 475 Field Communicator

Using ValveLink software, you can monitor the performance characteristics of the valve and obtain vital information without having to pull the valve from the line. I/P and Relay Integrity and Travel Deviation Diagnostics, as well as OnLine Friction and Deadband Analysis and Trending can be run while the valve is in service and operating. Valve Signature, Dynamic Error Band, and Step Response are displayed in an intuitive userfriendly environment that allows easy interpretation of data.

Diagnostic graphs can be superimposed over those previously stored to view areas of valve degradation. This allows plant personnel to concentrate efforts on equipment that needs repair, avoiding unnecessary maintenance. This diagnostic capability is readily accessible and available to you either in the control room or on the plant floor. In addition to the diagnostic features, ValveLink software contains an Audit Trail, Batch Runner for automating repetitive tasks, and Trending to view valve performance.

ValveLink software provides integration into AMS and DeltaVt systems with HART and fieldbus communications.

Product Bulletin

DVC6000 Digital Valve Controllers

TERMINAL BOX TERMINAL BOX COVER

62.1:DVC6000 December 2010

HOUSING

PNEUMATIC RELAY GAUGES

COVER

TRAVEL SENSOR

PRINTED WIRING BOARD ASSEMBLY

W9329

MODULE BASE ASSEMBLY

I/P CONVERTER

Figure 10. FIELDVUE DVC6000 Digital Valve Controller Assembly (ValveMounted Instrument)

Principle of Operation
DVC6000 instruments (figures 10 and 11) receive a set point and position the valve where it needs to be. D The input signal provides electrical power and the set point simultaneously. It is routed into the terminal box through a twisted pair of wires. D The input signal is then directed to the printed wiring board assembly where the microprocessor runs a digital control algorithm resulting in a drive signal to the I/P converter. D The I/P converter assembly is connected to supply pressure and converts the drive signal into a pressure output signal. D The I/P output is sent to the pneumatic relay assembly. The relay is also connected to supply

pressure and amplifies the small pneumatic signal from the I/P converter into a single larger pneumatic output signal used by a singleacting actuator. For doubleacting actuators, the relay accepts the pneumatic signal from the I/P converter and provides two pneumatic output signals. D The change in relay output pressure to the actuator causes the valve to move. D Valve position is sensed through the feedback linkage by the instruments travel sensor. The travel sensor is electrically connected to the printed wiring board to provide a travel feedback signal used in the control algorithm. The valve continues to move until the correct position is attained.

10

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

420 mA INPUT SIGNAL + HART

AUXILIARY TERMINALS TERMINAL BOX

PRINTED WIRING BOARD DRIVE SIGNAL

VALVE TRAVEL FEEDBACK

OUTPUT A

I/P CONVERTER PNEUMATIC RELAY SUPPLY PRESSURE

OUTPUT B

VALVE AND ACTUATOR

E0408 / IL

Figure 11. FIELDVUE DVC6000 Digital Valve Controller Block Diagram

Installation
The DVC6010 digital valve controller is designed for yoke mounting to sliding stem actuators. DVC6020 digital valve controllers are designed for mounting to rotary actuators or longstroke slidingstem actuators (over 4 inches travel). DVC6030 digital valve controllers are designed for mounting on virtually any quarterturn actuator. The DVC6005 digital valve controller base unit may be remote mounted on 2 inch pipestand or wall. The remotemounted DVC6005 base unit connects to the DVC6015, DVC6025, or DVC6035 feedback unit mounted on the actuator. Feedback wiring and pneumatic tubing to the control valve assembly must be connected in the field. Refer to Fisher bulletin 62.1:DVC6000(S1) (D103308X012) for DVC6000 digital valve controller dimensional information. The digital valve controllers are 4 to 20 mA loop powered and do not require additional power. Electrical connections are made in the terminal box.

All pressure connections on the digital valve controllers are 1/4 NPT internal connections. The digital valve controller outputs are typically connected to the actuator inputs using 3/8inch diameter tubing. Remote venting is available.

Ordering Information
When ordering, specify: 1. Actuator type and size 2. Maximum actuator travel or rotation 3. Options a. Supply pressure regulator b. Supply and output gauges c. HART filter d. Stainless steel housing (valvemounted instruments only) e. Remote mounting

11

Product Bulletin

DVC6000 Digital Valve Controllers

Table 2. EMC Summary ResultsImmunity

62.1:DVC6000 December 2010

Performance Criteria(1) Port Phenomenon Electrostatic discharge (ESD) Enclosure Radiated EM field Rated power frequency magnetic field Burst I/O signal/control Surge Conducted RF Basic Standard IEC 6100042 IEC 6100043 IEC 6100048 IEC 6100044 IEC 6100045 IEC 6100046
4 kV contact 8 kV air 80 to 1000 MHz @ 10V/m with 1 kHz AM at 80% 1400 to 2000 MHz @ 3V/m with 1 kHz AM at 80% 2000 to 2700 MHz @ 1V/m with 1 kHz AM at 80% 60 A/m at 50 Hz 1 kV 1 kV (line to ground only, each) 150 kHz to 80 MHz at 3 Vrms

Test Level

Pointto Point Mode A(2) A A A(2) A(2) A

Multidrop Mode A A A A A A

1. A = No degradation during testing. B = Temporary degradation during testing, but is selfrecovering. 2. Excluding auxiliary switch function, which meets Performance Criteria B.

Table 3. Hazardous Area ClassificationsCSA (Canada)

Certification Body Type Certification Obtained
Ex ia Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D,E, F,G per drawing GE42818 T5 Natural Gas Approved DVC60x0 DVC60x0S (x = 1,2,3) Explosion Proof Class I Division 1 GP B,C,D T6 Natural Gas Approved Class I Division 2 GP A,B,C,D T6 Class II Division 1 GP E,F,G T6 Class II Division 2 GP F,G T6 Class III Natural Gas Approved Ex ia Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D, E,F,G per drawing GE42818 T5 Natural Gas Approved CSA DVC6005 Explosion Proof Class I Division 1 GP B,C,D T6 Natural Gas Approved Class I Division 2 GP A,B,C,D T6 Class II Division 1 GP E,F,G T6 Class II Division 2 GP FG T6 Class III Natural Gas Approved Ex ia Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D, E,F,G per drawing GE42818 DVC60x5 (x = 1,2,3) Explosion Proof Class I Division 1 GP B,C,D T6 Class I Division 2 GP A,B,C,D T6 Class II Division 1,2 GP E,F,G T6 Class III

Entity Rating
Vmax = 30 VDC Imax = 226 mA Ci = 5 nF Li = 0.55 mH

Temperature Code

Enclosure Rating
Type 4X, IP66 Single Seal Device Type 4X, IP66 Single Seal Device

T5(Tamb v 80_C)

T6(Tamb v 80_C)

T6(Tamb v 80_C)

Type 4X, IP66 Single Seal Device

Vmax = 30 VDC Imax = 226 mA Ci = 5 nF Li = 0.55 mH

Voc = 9.6 VDC Isc = 3.5 mA Ca = 3.6 uF La = 100 mH

T5(Tamb v 80_C)

Type 4X, IP66 Single Seal Device Type 4X, IP66 Single Seal Device

T6(Tamb v 80_C)

T6(Tamb v 80_C)

Type 4X, IP66 Single Seal Device

Vmax = 30 VDC Imax = 17.5 mA Ci = 0 uF Li = 0 mH

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

Type 4X, IP66

Type 4X, IP66

Type 4X, IP66

12

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

Enclosure Rating

Table 4. Hazardous Area ClassificationsFM (United States)

Certification Body Type Certification Obtained
Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D, E,F,G per drawing GE42819 T5 Natural Gas Approved DVC60x0 DVC60x0S (x = 1,2,3) Explosion Proof Class I Division 1 GP B,C,D T6 Natural Gas Approved Class I Division 2 GP A,B,C,D T6 Class II Division 1 GP E,F,G T6 Class II Division 2 GP F,G T6 Class III Natural Gas Approved Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D,E, F,G per drawing GE42819 T5 Natural Gas Approved FM DVC6005 Explosion Proof Class I Division 1 GP B,C,D T6 Natural Gas Approved Class I Division 2 GP A,B,C,D T6 Class II Division 1 GP E,F,G T6 Class II Division 2 GP F,G T6 Class III Natural Gas Approved Intrinsically Safe Class I,II,III Division 1 GP A,B,C,D, E,F,G per drawing GE42819 DVC60x5 (x = 1,2,3) Vmax = 30 VDC Imax = 17.5 mA Ci = 0 nF Li = 0 mH Pi = 105 mW Vmax = 30 VDC Imax = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Entity Rating
Vmax = 30 VDC Imax = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Temperature Code

T5(Tamb v 80_C)

NEMA 4X

T6(Tamb v 80_C)

NEMA 4X

T6(Tamb v 80_C)

NEMA 4X

Voc = 9.6 VDC Isc = 3.5 mA Ca = 3.6 uF La = 100 mH Po = 8.4 mW

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

NEMA 4X

T6(Tamb v 60_C)

NEMA 4X

T6(Tamb v 60_C)

NEMA 4X

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

NEMA 4X

Explosion Proof Class I Division 1 GP A,B,C,D Class I Division 2 GP A,B,C,D Class II Division 1 GP E,F,G Class II Division 2 GP F,G

NEMA 4X

NEMA 4X

13

Product Bulletin

DVC6000 Digital Valve Controllers

Table 5. Hazardous Area ClassificationsATEX
Certificate Type Certification Obtained
II 1 G & D Intrinsically Safe Gas Ex ia IIC T5/T6 Dust Ex iaD 20 T100_C (Tamb v 80_C) Ex iaD 20 T85_C (Tamb v 75_C) Natural Gas Approved II 2 G & D Flameproof Gas Ex d IIC T5/T6 Dust Ex tD A21 IP66 T90_C (Tamb v 85_C) Ex tD A21 IP66 T80_C (Tamb v 75_C) Natural Gas Approved II 3 G & D Type n Gas Ex nCnL IIC T5/T6 Dust Ex tD A22 IP66 T85_C (Tamb v 80_C) Ex tD A22 IP66 T80_C (Tamb v 75_C) Natural Gas Approved II 1 G & D Intrinsically Safe Gas Ex ia IIC T5/T6 Dust Ex iaD 20 T100_C (Tamb v 80_C) Ex iaD 20 T85_C (Tamb v 75_C) Natural Gas Approved II 2 G & D Flameproof Gas Ex d IIC T5/T6 Dust Ex tD A21 IP66 T90_C (Tamb v 85_C) Ex tD A21 IP66 T80_C (Tamb v 75_C) Natural Gas Approved II 3 G & D Type n Gas Ex nCnL IIC T5/T6 Dust Ex tD A22 IP66 T85_C (Tamb v 80_C) Ex tD A22 IP66 T80_C (Tamb v 75_C) Natural Gas Approved
continued

62.1:DVC6000 December 2010

Entity Rating

Temperature Code

Enclosure Rating

Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

T5(Tamb v 80_C) T6(Tamb v75_C)

IP66

DVC60x0 DVC60x0S (x = 1,2,3)

T5(Tamb v 85_C) T6(Tamb v75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v75_C)

IP66

ATEX

Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 mW

Uo = 9.6 VDC Io = 3.5 mA Co = 3.6 uF Lo = 100 mH Po = 8.4 mW

T5(Tamb v 80_C) T6(Tamb v75_C)

IP66

DVC6005

T5(Tamb v 85_C) T6(Tamb v75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v75_C)

IP66

14

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

Certification Obtained
II 1 G & D Intrinsically Safe Gas Ex ia IIC T4/T5/T6 Dust Ex iaD 20 T135_C (Tamb v 125_C) Ex iaD 20 T100_C (Tamb v 95_C) Ex iaD 20 T85_C (Tamb v 80_C) II 2 G & D Flameproof Gas Ex d IIC T4/T5/T6 Dust Ex tD A21 IP66 T130_C (Tamb v 125_C) Ex tD A21 IP66 T100_C (Tamb v 95_C) Ex tD A22 IP66 T85_C (Tamb v 80_C) II 3 G & D Type n Gas Ex nA IIC T4/T5/T6 Dust Ex tD A22 IP66 T130_C (Tamb v 125_C) Ex tD A22 IP66 T100_C (Tamb v 95_C) Ex tD A22 IP66 T85_C (Tamb v 80_C)

Table 5. Hazardous Area ClassificationsATEX (continued)

Certificate Type Entity Rating Temperature Code Enclosure Rating

Ui = 30 VDC Ii = 17.5 mA Ci = 0 uF Li = 0 mH Pi = 105 mW

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

ATEX

DVC60x5 (x = 1,2,3)

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

15

Product Bulletin

DVC6000 Digital Valve Controllers

Table 6. Hazardous Area ClassificationsIECEx
Certificate Type Certification Obtained
Intrinsically Safe Gas Ex ia IIC T5/T6 per drawing GE42990 Natural Gas Approved DVC60x0 DVC60x0S (x = 1,2,3) Flameproof Gas Ex d IIC T5/T6 Natural Gas Approved Type n Gas Ex nC IIC T5/T6 Natural Gas Approved Intrinsically Safe Gas Ex ia IIC T5/T6 per drawing GE42990 Natural Gas Approved IECEx Flameproof Gas Ex d IIC T5/T6 Natural Gas Approved Type n Gas Ex nC IIC T5/T6 Natural Gas Approved Intrinsically Safe Gas Ex ia IIC T4/T5/T6 Ui = 30 VDC Ii = 17.5 mA Ci = 0 uF Li = 0 mH Pi = 105 mW Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

62.1:DVC6000 December 2010

Entity Rating
Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Temperature Code

Enclosure Rating

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C) T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

Uo = 9.6 VDC Io = 3.5 mA Co = 3.6 uF Lo = 100 mH Po = 8.4 mW

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

DVC6005

T5(Tamb v 80_C) T6(Tamb v 75_C) T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

IP66

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

DVC60x5 (x = 1,2,3)

Flameproof Gas Ex d IIC T4/T5/T6 Type n Gas Ex nA IIC T4/T5/T6

IP66

IP66

16

Product Bulletin
62.1:DVC6000 December 2010

DVC6000 Digital Valve Controllers

Enclosure Rating

Table 7. Hazardous Area ClassificationsNEPSI

Certificate Type Certification Obtained
Intrinsically Safe Gas Ex ia IIC T5/T6 Dust DIP A21 T5 Flameproof Gas Ex d IIC T5/T6 Dust DIP A21 T5 Intrinsically Safe Gas Ex ia IIC T5/T6 Dust DIP A21 T5 Flameproof Gas Ex d IIC T5/T6 Dust DIP A21 T5 Intrinsically Safe Gas Ex ia IIC T4/T5/T6 Flameproof Gas Ex d IIC T4/T5/T6 Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Entity Rating
Ui = 30 V Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Temperature Code

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

DVC60x0 DVC60x0S (x = 1,2,3)

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

NEPSI DVC6005

Uo = 9.6 VDC Io = 3.5 mA Co = 3.6 uF Lo = 100 mH Po = 8.4 mW

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

IP66

DVC60x5 (x = 1,2,3

IP66

17

Product Bulletin

DVC6000 Digital Valve Controllers

Table 8. Hazardous Area ClassificationsINMETRO
Certificate Type Certification Obtained
Intrinsically Safe Gas BREx ia IIC T5/T6 per drawing GE42990 Natural Gas Approved DVC60x0 DVC60x0S (x = 1,2,3) Flameproof Gas BREx d IIC T5/T6 Natural Gas Approved Type n Gas BR-Ex nC IIC T5/T6 Natural Gas Approved Intrinsically Safe Gas BREx ia IIC T5/T6 per drawing GE42990 Natural Gas Approved INMETRO DVC6005 Flameproof Gas BREx d IIC T5/T6 Natural Gas Approved Type n Gas BREx nC IIC T5/T6 Natural Gas Approved Intrinsically Safe Gas BREx ia IIC T4/T5/T6 Ui = 30 VDC Ii = 17.5 mA Ci = 0 uF Li = 0 mH Pi = 105 mW Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

62.1:DVC6000 December 2010

Entity Rating
Ui = 30 VDC Ii = 226 mA Ci = 5 nF Li = 0.55 mH Pi = 1.4 W

Temperature Code

Enclosure Rating

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C) T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

Uo = 9.6 VDC Io = 3.5 mA Co = 3.6 uF Lo = 100 mH Po = 8.4 mW

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

T5(Tamb v 80_C) T6(Tamb v 75_C) T5(Tamb v 80_C) T6(Tamb v 75_C)

IP66

IP66

T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C) T4(Tamb v 125_C) T5(Tamb v 95_C) T6(Tamb v 80_C)

IP66

DVC60x5 (x = 1,2,3)

Flameproof Gas BREx d IIC T4/T5/T6 Type n Gas BREx nA IIC T4/T5/T6

IP66

IP66

18

Product Bulletin
62.1:DVC6000 December 2010 Note Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use, or maintenance of any product. Responsibility for the selection, use, and maintenance of any product remains with the purchaser and end user.

DVC6000 Digital Valve Controllers

19

Product Bulletin

DVC6000 Digital Valve Controllers

62.1:DVC6000 December 2010

Fisher, FIELDVUE, ValveLink, and DeltaV are marks owned by one of the companies in the Emerson Process Management business division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners. The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice. Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.

Emerson Process Management Marshalltown, Iowa 50158 USA Sorocaba, 18087 Brazil Chatham, Kent ME4 4QZ UK Dubai, United Arab Emirates Singapore 128461 Singapore www.Fisher.com
20 E Fisher Controls International LLC 2000, 2010; All Rights Reserved