AV-21AT

STANDARD CIRCUIT DIAGRAM

■ NOTE ON USING CIRCUIT DIAGRAMS ● Type
1. SAFETY No indication : Ceramic capacitor
The components identified by the ! symbol and shading are MY : Mylar capacitor
critical for safety. For continued safety replace safety critical MM : Metalized mylar capacitor
components only with manufactures recommended parts. PP : Polypropylene capacitor
MPP : Metalized polypropylene capacitor
2. SPECIFIED VOLTAGE AND WAVEFORM VALUES MF : Metalized film capacitor
The voltage and waveform values have been measured under the TF : Thin film capacitor
following conditions. BP : Bipolar electrolytic capacitor
(1) Input signal : Colour bar signal TAN : Tantalum capacitor
(2) Setting positions of each knob/button and variable resistor (3) Coils
: Original setting position when No unit : [µH]
shipped Others : As specified
(3) Internal resistance of tester : DC 20kΩ/V (4) Power Supply
(4) Oscilloscope sweeping time : H ➞ 20µS/div : B1
:V ➞ 5mS/div : 12V
: Others ➞ Sweeping time is : 9V
specified. : 5V
(5) Voltage values : All DC voltage values * Respective voltage values are indicated.
* Since the voltage values of signal circuit vary to some extent (5) Test point
according to adjustments, use them as reference values. : Test point

: Only test point display

3. INDICATION OF PARTS SYMBOL [EXAMPLE]
● In the PW board : R1209 ➞ R209 (6) Connecting method
: Connector
4. INDICATIONS ON THE CIRCUIT DIAGRAM : Wrapping or soldering
(1) Resistors : Receptacle
● Resistance value
No unit : [Ω] (7) Ground symbol
K : [KΩ] # : LIVE side ground
M : [MΩ] " : ISOLATED (NEUTRAL) side ground
● Rated allowable power : EARTH ground
No indication : 1/4 [W] : DIGITAL ground
Others : As specified
● Type 5. NOTE FOR REPAIRING SERVICE
No indication : Carbon resistor This model’s power circuit is partly different in the GND. The differ-
OMR : Oxide metal film resistor ence of the GND is shown by the LIVE : (#) side GND and the
MFR : Metal film resistor ISOLATED (NEUTRAL) : (") side GND. Therefore, care must be
MPR : Metal plate resistor taken for the following points.
UNFR : Non-flammable resistor (1) Do not touch the LIVE side GND or the LIVE side GND and the
FR : Fusible resistor ISOLATED (NEUTRAL) side GND simultaneously. If the above
* Composition resistor 1/2 [W] is specified as 1/2S or Comp. caution is not respected, an electric shock may be caused.
(2) Capacitors Therefore, make sure that the power cord is surely removed from
● Capacitance value the receptacle when, for example, the chassis is pulled out.
1 or higher : [pF] (2) Do not short between the LIVE side GND and ISOLATED (NEU-
less than 1 : [µF] TRAL) side GND or never measure with a measuring apparatus
● Withstand voltage (oscilloscope, etc.) the LIVE side GND and ISOLATED (NEU-
No indication : DC50 [V] TRAL) side GND at the same time. If the above precaution is
AC indicated : AC withstand voltage [V] not respected , a fuse or any parts will be broken.
Others : DC withstand voltage [V]
* Electrolytic Capacitors ● Since the circuit diagram is a standard one, the circuit and
47/50 [Example]: Capacitance value [µF]/withstand voltage [V] circuit constants may be subject to change for improvement
without any notice.

No. 56013 2-3

AV-21AT

CONTENTS
SEMICONDUCTOR SHAPES ........................................................... 2-4
BLOCK DIAGRAM ............................................................................ 2-5
CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM (Including CRT SOCKET PWB) ......................................... 2-7
PATTERN DIAGRAMS
MAIN PWB PATTERN ............................................................................................................. 2-11
CRT SOCKET PWB PATTERN ............................................................................................... 2-13

SEMICONDUCTOR SHAPES
TRANSISTOR
BOTTOM VIEW FRONT VIEW TOP VIEW
CHIP TR

E C

B
B C E
ECB (G)(D)(S)
ECB E C B B E

IC
BOTTOM VIEW FRONT VIEW TOP VIEW

1 N
OUT

IN 1 N
IN E OUT 1 N

CHIP IC
TOP VIEW

N 1
N

N 1
N
N

2-4 No. 56013

 AV-21AT AV-21AT

BLOCK DIAGRAM

MAIN PWB
SP01

TU001 IF
Q102
SF102 IC651 9
TUNER IF AMP OUT SP01
AUDIO AMP

IN
3 HEADPHONE
SF122

Q103 ECO
SW VIDEO
FRONT IN
21 18,19 30 REMOCON
QSS IN SAW AUDIO OUT AUDIO
SCL/SDA

37,38 25
IC703 34 SCL 3.58/ KEY
RST SDA OTH
5V REG/RESET IC301
IC701 1 CHIP DECODER 10,11,12 IND.
RGB
SCL MICRO COMPUTER 6,7,8 EXT
CRT SOCKET PWB
IC702 SDA 2,3 OSD 30,31,32
RGB RGB (WITHIN MAIN PWB)
MEMORY
VIDEO VIDEO AUDIO
IN OUT IN H.OUT V.OUT
24 36 29 42 46

R/G/B Q351-Q353 V01

REAR RGB OUT CRT
VIDEO
IN
AUDIO

VIDEO
OUT
AUDIO
V.OUT 5 IC421 2
DY(V)
V.OUT

DY(H)

D901 H.OUT Q522

POWER SW RECT H.OUT DEF. YOKE
IC971 5V
F901 5/9V REG. 9V

TP-B1
AC IN T921 FOCUS
IC921 SW
POWER T522
TRANSF. SCREEN
REG. HVT
EHV

PC921 IC941
VOLTAGE ERROR
FEEDBACK AMP

No. 56013 2-5 2-6 No. 56013

 AV-21AT AV-21AT

CIRCUIT DIAGRAMS MAIN PWB CIRCUIT DIAGRAM (1/2)

SCG-1247A-H2 (AV-21AT)

No. 56013 2-7 2-8 No. 56013

 AV-21AT AV-21AT

MAIN PWB CIRCUIT DIAGRAM (2/2)

CRT SOCKET

(WITHIN MAIN PWB)

SCG-1247A-H2 (AV-21AT)

No. 56013 2-5

2-9 2-6
2-10 No. 56013