Scribd
Upload
2K views

Lecture 2. Types of Machine Drawing

An assembly drawing shows how individual machine parts fit together as a complete unit. It describes the shape and positioning of parts, identifies each component, and provides a parts list. Section lines on parts should vary to distinguish shapes. Every part is identified by a number in a balloon with a leader ending on or near the part. Sub-assembly drawings show pre-assembled components that make up a more complex machine. Detail drawings include dimensions and other information to facilitate manufacturing individual parts.

Uploaded by

addisudagne
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
2K views

Lecture 2. Types of Machine Drawing

An assembly drawing shows how individual machine parts fit together as a complete unit. It describes the shape and positioning of parts, identifies each component, and provides a parts list. Section lines on parts should vary to distinguish shapes. Every part is identified by a number in a balloon with a leader ending on or near the part. Sub-assembly drawings show pre-assembled components that make up a more complex machine. Detail drawings include dimensions and other information to facilitate manufacturing individual parts.

Uploaded by

addisudagne
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 19

Debre Markos University Mechanical Engineering Department

Machine Drawing MEng 2301


Lecture 2 Types of Machine Drawing
By: Addisu Dagne 2012/13 Academic Year
1 3/13/2013

Assembly Drawing
An assembly working-drawing indicates how the individual

parts of a machine or mechanism are assembled to make a complete unit. An assembly working-drawing serves the following purposes:
o It describes the shape of the assembled unit. o it indicates how the parts of the assembled unit are positioned in

relation to each other. o It identifies each component that forms part of the assembled unit. o It provides a parts list that describes and lists essential data concerning each part of the assembled unit.

It is preferable that the dimension of the parts of the

machine are not shown as they would crowd the drawing.


2 3/13/2013

Assembly Drawing

3/13/2013

Assembly Drawing
The parts list of an

assembly workingdrawing itemizes important data about each part of an assembled unit such as part name, material, quantity required, and size specifications.

3/13/2013

Sectioned parts on Assembly Drawings


The section lines on sectioned adjacent parts of assembly

working-drawings should vary in order to make the shapes of the sectioned parts more apparent. Different types of section lines as well as different spacing and different angles of inclination are recommended for this purpose. As a general rule solid parts that do not have interior features, such as shafts, rivets, pins, keys, and threaded fasteners, remain un-sectioned on assembly workingdrawings.

3/13/2013

Sectioned parts on Assembly Drawings

3/13/2013

Assembly Drawing - Parts Identification


Every part on an assembly working-drawing must be

identified by means of a part number. Each part number is lettered within a parts identification balloon that has a leader that ends at or on the part identified. Hints Regarding Parts Balloons and leaders Group balloons in straight lines, clockwise and in sequence, if possible, around the view or views. Place balloons at a reasonable distance from the views. A minimum distance of 25 mm is recommended. Use straight leaders when possible. Bend a leader when it is necessary to maintain clarity.
7 3/13/2013

Assembly Drawing - Parts Identification


Draw leaders at varying angles. Avoid vertical and

horizontal leaders. Place parts balloons adjacent to parts being identified in order to avoid extra-long leaders and the need to pass over too many other parts. Leaders that pass over sectioned parts should be drawn so they do not become confused with the section lines. Avoid drawing leaders through the corners of parts.

3/13/2013

Assembly Drawing - Parts Identification

3/13/2013

Assembly Drawing - Parts Identification

10

3/13/2013

Assembly Drawing - Parts Identification

11

3/13/2013

Assembly Drawing - Parts Identification


An arrowhead is used A dot is used when a leader is

when a leader terminates at a line that represents the edge of a part.

drawn onto a surface of a part across a line that represents the edge of the part.

12

3/13/2013

Assembly Drawing - Parts Identification


Leaders can be bent to maintain clarity.

Keep bends to a minimum

13

3/13/2013

POINTS TO REMEMBER
As a general rule, assembly working-drawings are not

dimensioned. Hidden lines that do not add to the clarity of an assembly working-drawing should be omitted. Do not position parts identification balloons haphazardly. Try to group them in straight lines around the views, preferably clockwise and in sequence. Parts leaders should be drawn at an angle. Adjacent parts that are sectioned should have different types of section lines, should have section lines drawn at different angles, or should be spaced differently in order to make them readily apparent.
3/13/2013

14

POINTS TO REMEMBER
On assembly working-drawings shafts, rivets, keys,

screw-thread fasteners, and other solid parts are not usually sectioned. When necessary, reference information is shown on assembly working drawings in the form of notes and dimensions.

15

3/13/2013

Sub-assembly Drawings
Many assemblies such as an automobile, lathe, etc., are

assembled with many pre-assembled components as well as individual parts. These pre-assembled units are known as sub-assemblies. A sub-assembly drawing is an assembly drawing of a group of related parts, that form a part in a more complicated machine. Examples of such drawings are: lathe tail-stock, diesel engine fuel pump, carburetor, etc.

16

3/13/2013

Part Drawing/Detail Drawing


A detail drawing is a drawing of an individual part,

which includes an orthographic projection and dimensions. Component or part drawing is a detailed drawing of a component to facilitate its manufacture. A part drawing shows the number of views of each single part of a machine to facilitate its manufacturing. It should give all the dimensions, limits, tolerances and special finishing; if any.

17

3/13/2013

Catalogue Drawings
Special assembly drawings are prepared for company

catalogues. These drawings show only the pertinent details and dimensions that would interest the potential buyer.

Schematic Drawings
A schematic drawing is the simplified illustration of a

machine or system, replacing all the elements by their respective conventional representations, to understand the principle of operation.
18 3/13/2013

Shop Drawings
Shop Drawing A shop drawing includes the part

drawing, subassembly and the complete assembly of a product for manufacturing.

Patent Drawings
A patent drawing gives the correct and complete

features of a new technology or innovation adopted for a machine or system. The drawings are pictorial in nature and self explanatory but not useful for production purposes.

19

3/13/2013

You might also like