Scribd
Upload
29 views2 pages

Thermocouple For Use in The Plastics Industry: Models

This document describes a thermocouple for use in the plastics industry. It has a maximum temperature limit of -40 to 250 degrees Celsius and reference tolerances of +/- 2.5 degrees Celsius. It features an AISI 303 stainless steel tip, adjustable spring mounting, and cable to DIN standards. The thermocouple comes in models with bayonet or screw mounts and various element, cable, sheathing, and connector options.

Uploaded by

Patricio Cruz Cornejo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
29 views2 pages

Thermocouple For Use in The Plastics Industry: Models

This document describes a thermocouple for use in the plastics industry. It has a maximum temperature limit of -40 to 250 degrees Celsius and reference tolerances of +/- 2.5 degrees Celsius. It features an AISI 303 stainless steel tip, adjustable spring mounting, and cable to DIN standards. The thermocouple comes in models with bayonet or screw mounts and various element, cable, sheathing, and connector options.

Uploaded by

Patricio Cruz Cornejo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TC5

Thermocouple for use in the plastics industry

Main characteristics
Max. temperature limit: - 40 ... + 250 C (see table for thermocouple cable used) Reference tolerances: Standards IEC 584.2 class 2: for type J, K: 2.5 C (- 40 ... + 333 C) AISI 303 stainless steel tip Mount threading adjustment spring: 8mm, length 300mm. Cable to DIN standard

MODELS

TC5 B: with bayonet mount

Li

Lc

TC5 V: with screw mount

Li

Lc

ORDER CODE

T C

0 0 0

CODE Model With bayonet mount With screw mount Elemento + giunto caldo Isolated single Grounded single Isolated double Grounded double Element type Fe - Cu/Ni Ni/Cr - Ni/Al Cable (to DIN standard) GSC GSC / SCH TTS TES Sheathing material AISI 303 Sheathing diameter (mm) 5 6 8 H * I ** J *** 1 2 3 4 B V A R T Certificates Certificate of conformity Calibration Report SIT Certified

LENGTHS AND ACCESSORIES Li = Immersion length (mm) * Standard: 10 - 15 - 25 - 35mm (*) Lengths differ from standard only for 6 and 8mm. Connector type A B C D E Standard male Standard male + female Standard male + panel Mignon male Mignon male + female Lc = Cable length (dm) Standard length from 5 to 100dm with 5dm pitch

J K

2 3 5 6

(*) Standard sheathing length 15mm (**) Standard sheathing length 15-25-35mm (***) Standard sheathing length 10mm Mount threading (F) G1/4 M 12x1 M 12x1.5 M 12x1.75 Mount material Galvanized carbon steel 3

CONNECTOR TYPE

B O P Q

GEFRAN spa reserves the right to make aesthetic or functional changes at any time and without notice

GEFRAN spa via Sebina, 74 25050 PROVAGLIO DISEO (BS) - ITALIA ph. 0309888.1 - fax. 0309839063 Internet: http://www.gefran.com www.gefranonline.com

DTS_TC5_0607_ENG

You might also like