Scribd Logo
Upload

Welcome to Scribd!

  • 765 views

    ME 472 - Engineering Metrology and Quality Control: Linear and Angular Measurements

    Uploaded by

    Atul Gaur
    The document discusses various tools used for measuring linear and angular dimensions in mechanical engineering metrology. It describes graduated tools like rules, vernier calipers, micrometers, and protractors used to directly measure lengths and angles. Non-graduated tools like calipers, gauges, and gauge blocks are also covered, which provide indirect measurements. Finally, the document explains how to properly use these tools to obtain accurate measurements.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    ME 472 - Engineering Metrology and Quality Control: Linear and Angular Measurements

    Uploaded by

    Atul Gaur
    765 views19 pages
    The document discusses various tools used for measuring linear and angular dimensions in mechanical engineering metrology. It describes graduated tools like rules, vernier calipers, micrometers, and protractors used to directly measure lengths and angles. Non-graduated tools like calipers, gauges, and gauge blocks are also covered, which provide indirect measurements. Finally, the document explains how to properly use these tools to obtain accurate measurements.

    Original Title

    2. ME472_5

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses various tools used for measuring linear and angular dimensions in mechanical engineering metrology. It describes graduated tools like rules, vernier calipers, micrometers, and protractors used to directly measure lengths and angles. Non-graduated tools like calipers, gauges, and gauge blocks are also covered, which provide indirect measurements. Finally, the document explains how to properly use these tools to obtain accurate measurements.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    765 views19 pages

    ME 472 - Engineering Metrology and Quality Control: Linear and Angular Measurements

    Uploaded by

    Atul Gaur
    The document discusses various tools used for measuring linear and angular dimensions in mechanical engineering metrology. It describes graduated tools like rules, vernier calipers, micrometers, and protractors used to directly measure lengths and angles. Non-graduated tools like calipers, gauges, and gauge blocks are also covered, which provide indirect measurements. Finally, the document explains how to properly use these tools to obtain accurate measurements.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 19

    ME 472 Engineering Metrology and Quality Control

    Linear and Angular Measurements

    Mechanical Engineering University of Gaziantep

    Dr. A. Tolga Bozdana Assistant Professor

    Measuring tools and instruments


    Measuring tools and instruments

    Direct (contact) measurement (e.g. micrometer or caliper)

    Indirect (non-contact) measurement (advanced methods such as optical, ultrasonic, laser, etc.)

    Graduated (either linear or angular graduations incorporated into measuring system of the tool)

    Non-graduated (gauges or adjustable tools which compare the measurements)

    NEXT WEEK!

    Rules Vernier Calipers Vernier Gauges Micrometers Protractors Dial Indicators

    Calipers Gauges and Gauge Blocks Sine Bar Special-purpose tools

    Graduated Linear Measurement - Rules


    Imperial steel rule with various lengths having graduations on each side Same rule with relatively larger graduations

    Metric steel rule with various lengths having graduations on each side

    resolution?
    How to read a rule: A = 12 mm (12th graduation) B = 22 mm (22nd graduation) C = 31.5 mm (between 31st and 32nd) D = 40.5 mm (between 40th and 41st)
    2

    Graduated Linear Measurement - Vernier Calipers


    More precise tools capable of measuring external and internal dimensions as well as depths.

    How to read a vernier caliper: First, read the graduation on the main scale just before the vernier scale starts (i.e. 19th graduation, which gives 19 mm) Next, read the graduation on the vernier scale where two graduation lines on main and vernier scales perfectly match (i.e. 32nd graduation, which gives 32 * 1/50 = 0.64 mm) Then, add the fine reading into the main reading (i.e. 19 + 0.64 = 19.64 mm)
    3

    Graduated Linear Measurement - Vernier Calipers

    Direct reading of an internal length using digital vernier caliper Direct reading of an external length using digital vernier caliper

    Vernier caliper with a dial indicator

    Graduated Linear Measurement - Vernier Height Gauges


    Designed for use in toolrooms, workshops, inspection departments to measure or mark off vertical heights and locating center distances.

    Standard Height gauge

    Dial Height Gauge

    Digital Height Gauge


    5

    Graduated Linear Measurement - Vernier Depth Gauges


    Designed for use in toolrooms, workshops, inspection departments to measure depths of holes, slots, recesses, and so on.

    Standard Depth Gauge

    Dial Depth Gauge

    Digital Depth Gauge


    6

    Graduated Linear Measurement - Outside Micrometers


    VERNIER READING THIMBLE READING

    Metric Micrometer
    SLEEVE (BARREL) READING

    Metric Vernier Micrometer


    B

    How to read a vernier metric micrometer: Sleeve div. = 1 mm Thimble div. = 1/50th of sleeve sub-div. = 1/100 mm
    Thimble Division

    Vernier Division D

    Vernier div. = 1/10th of thimble div. = 1/1000 mm A. The highest figure: 5 * (sleeve div.) = 5 mm
    C

    B. The half-figures: 1 * (sleeve sub-div.) = 0.5 mm C. The highest figure: 28 * (thimble div.) = 0.28 mm D. The matching figure: 3 * (vernier div.) = 0.003 mm

    Sleeve Division

    FINAL READING = A + B + C + D = 5.783 mm

    Graduated Linear Measurement - Outside Micrometers

    Dial-indicating Micrometer

    V-anvil Micrometer (measuring odd-fluted taps, milling cutters, reamers, and checking out of roundness)

    Direct-reading Micrometer

    Screw Thread Micrometer (measuring pitch diameter of screw threads)


    8

    Graduated Linear Measurement - Inside Micrometers

    Standard Inside Micrometers

    Digital Inside Micrometers

    Graduated Linear Measurement - Micrometer Bore and Depth Gauges

    Micrometer Hole and Bore Gauges

    Inside Micrometer Set

    Micrometer Depth Gauges


    10

    Graduated Angular Measurement - Protractors

    (a)

    Simple Protractor (measuring angles from 0 to 180)

    (b)

    Universal Bevel Protractor (main scale consists of 4 portions of 90)

    Measuring acute (a) and obtuse (b) angles

    How to read an angle on a bevel protractor: Main div. = 1 = 60 Vernier div. = 1/12th of main div. 0.0833 = 5 The highest figure: 50 * (main div.) = 50 The matching figure: 4 * (vernier div.) 0.333 = 20 The final reading is: 50.333 or 50 20
    11

    Special Purpose Measurement Tools

    Level (used for setting up and testing machinery)

    Combination Set (consisting of a 90 square, a level, a depth/height gauge and a bevel protractor with a centring head)

    Dial test indicator on a magnetic stand (used as an accessory with machine tools for accurate and delicate measurements)
    12

    Non-Graduated Linear Measurement - Calipers


    Standard calipers have a fine adjustment screw and a quick-adjusting spring nut. Accuracy obtained with these tools depends mostly on the inherent skill of users. The measurements are carefully transferred to a graduated measuring tool.

    Caliper for inside measurement

    Caliper for outside measurement

    Caliper used as a divider


    13

    Non-Graduated Linear Measurement - Gauges


    Telescopic Gauges (consisting of a handle with two plunger-contacts at right angles which both lock simultaneously)

    Small Hole Gauges (consisting of an expanding ball head adjusted to size by a knurled knob to provide an accurate feel for obtaining measurements in a hole or slot)

    Surface Gauge (consisting of a ground rectangular base with a round upright rod and a fine adjustment feature in the base. It can be used in a layout work for marking lines on vertical or horizontal surfaces, and also used in inspection work as height or depth gauge)
    14

    Non-Graduated Linear Measurement - Special Purpose Gauges

    Screw Pitch Gauges (consisting of a metal case containing many separate leaves. Each leaf has teeth corresponding to a definite pitch. By matching the teeth with the thread on work, the correct pitch can be read directly from the leaf)

    Tap and Drill Gauges (consisting of a flat rectangular steel plate with holes accurately drilled and identified according to their size)

    Radius Gauges (available as individual leaves and each leaf is marked with its radius. They are designed to check both convex and concave radii)

    15

    Non-Graduated Linear Measurement - Rectangular Gauge Blocks

    (a)

    (b)

    (c)

    Linear Gauge Blocks: (a) rectangular, (b) square, (c) square with center hole

    16

    Non-Graduated Angular Measurement - Angle Gauge Blocks


    parallel +3 +5 Target: 38 +30

    Complete set of angle gauge blocks

    Setting a revolving magnetic chuck using angle gauge blocks True Square
    17

    Non-Graduated Angular Measurement - Sine Bar

    How to use Sine Bar: We want to set an angle of 14 12 using a 10 mm sine bar. This means: l = 10 mm and = 14.2 So: h = l * sin = 2.453 mm Thus, a combination of gauge blocks providing this height must be used. Limitations of Sine Bar: When using a sine bar, the height setting is limited by available gauge block divisions. This causes an error that may be negligible or quite significant depending on the accuracy of measurement. Due to the nature trigonometry; at larger angles, the sine bar is susceptible to errors in the length of sine bar as well as in the height of gauge blocks. 18

    You might also like