Scribd
Upload
52 views

Department Semester Subject Code Subject Name: ECE 6 6EC2 Microprocessor and Microcontroller

This document contains the semester subjects, subject codes, and topics for two subjects - Microprocessor and Microcontroller and Control Systems - for the 6th semester of an Electronics and Communication Engineering degree. The Microprocessor and Microcontroller section covers topics like the different bus types in the 8085 microprocessor, machine cycles, address and data bus demultiplexing, architecture, programming model, pin diagram, interrupts, and addressing modes. The Control Systems section discusses open and closed loop systems, transfer function determination using block diagrams and signal flow graphs, feedback control systems, multivariable systems, block diagram reduction techniques, digital control systems, and more.

Uploaded by

ektagoyal273
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
52 views

Department Semester Subject Code Subject Name: ECE 6 6EC2 Microprocessor and Microcontroller

This document contains the semester subjects, subject codes, and topics for two subjects - Microprocessor and Microcontroller and Control Systems - for the 6th semester of an Electronics and Communication Engineering degree. The Microprocessor and Microcontroller section covers topics like the different bus types in the 8085 microprocessor, machine cycles, address and data bus demultiplexing, architecture, programming model, pin diagram, interrupts, and addressing modes. The Control Systems section discusses open and closed loop systems, transfer function determination using block diagrams and signal flow graphs, feedback control systems, multivariable systems, block diagram reduction techniques, digital control systems, and more.

Uploaded by

ektagoyal273
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Department Semester Subject Code Subject Name

ECE 6th 6EC2 Microprocessor and microcontroller

1. Name various types of buses in8085 mp. Explain the functioning of each of them 2. Explain various machine cycles used in 8085. Give status of IO/M, SO ,S1 for each machine cycle 3. What is the need of de-multiplexing of address and data bus in 8085? Explain demultiplexing of the buses using a schematic diagram 4. Explain in detail architecture of 8085 mp with the help of a block diagram. 5. Draw the functional block or programming model of 8085 mp and explain working each unit in detail. 6. Draw the pin diagram of 8085 mp. Explain its various pins. 7. Distinguish between a) mask able and non-mask able interrupts b) Hardware and software interrupts. 8. Write short note on a) Edge triggered and level triggered interrupts b) Vectored interrupts. 9. Explain the interrupt structure of 8085 mp. Also explain the instructions related to it. 10. Explain various addressing modes in 8085 mp.

Department Semester Subject Code Subject Name

ECE 6th 6EC5 Control systems

1. Compare the open and closed loop control system by giving suitable example for each. 2. Determine the c(s)/r(s) ratio for the system shown in the following diagram. R(S) + + H2 G1 H2 G2 G3

C(S)

3. Obtain the transfer function by using block diagram reduction technique. Verify the result using signal flow graphs.
G4

R(S) + -

+ -

G1

G2

G3

C(S)

H2 G3 H1

4. Draw schematic diagram of a closed loop control system of your choice. Draw its block diagram also. 5. Define multivariable control system. 6. Draw signal flow graph of the given block diagram and then reduce transfer function by using Masons gain formula.
G4 H2

R(S) + -

G1 H1

G2

+ H3

G3

- C(S)

7. Simplify the block diagram shown in fig given below and obtain the transfer function relating C(S) and R(S).
H3

R(S) + -

G1 H1

G2

G3

C(S) -

8. Obtain simplified block diagram using: i. ii. Block diagram reduction technique. Signal flow graph for the block diagram shown below
G3

R(S) + H1 H2

G1

G2

G4

C(S)

H3

9. The block diagram representation of feedback control system is shown in fig. a) Use the block diagram reduction technique to find the transfer function of C/R. b) Draw the equivalent signal flow graph and confirm C/R using masons gain formula.
G3

R(S) + -

G1

+ -

G2 H2

C(S)

H1

10. Write short note on digital control system.

You might also like