Compresor Kaeser CSD100 PDF

SERVICE MANUAL
Screw Compressor Model: CSD 100/125

No.: 9_5704_05USE
Contents
Chapter --- page
Regarding this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 --- 1

1.1 1.2 1.3 1.4 1.4.1 1.4.2 Handling the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbols and Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous notices and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 1 1 1 ------------1 1 1 1 1 2
Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 --- 3

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.7.1 2.7.2 2.8 2.8.1 2.8.2 2.9 2.9.1 2.9.2 2.10 2.10.1 2.10.2 2.11 2.11.1 2.11.2 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ambient Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Free Air Delivery (FAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sound Pressure Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motor and Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressor motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling Oil Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Design data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling Water Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prepared for heat recovery (option W1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Heat Recovery (option W2 / W3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 ------------------------------------------3 4 4 4 4 5 5 5 5 6 6 7 7 7 8 9 9 9 10 10 10
Safety and Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 --- 13

3.1 3.2 3.3 3.3.1 3.3.2 3.4 3.5 3.5.1 3.5.2 3.5.3 3.5.4 3.5.5 3.6 3.7 3.7.1 3.7.2 3.8 Proper Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Improper Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Users Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Qualified personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adhere to inspection schedules and accident prevention regulations. . . . Safety Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Danger from electricity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dangers from compressed air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dangers from spring forces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further dangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Danger zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fire supression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 ----------------------------------13 13 13 13 14 14 14 15 15 16 16 16 17 19 19 19 19
Contents
Chapter --- page
Design and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 --- 20

4.1 4.1.1 4.1.2 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.4 4.4.1 4.4.2 4.4.3 4.4.4 4.5 4.6 Machine Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volt ---free Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine mountings (option H1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter mat panels (option K3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating States and Control Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controller Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modulation Control (option C1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIGMA CONTROL Keys and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 --------------------------------20 20 21 22 23 23 23 23 23 24 24 24 24 25 25 26
Installation and Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 5 --- 28

5.1 5.2 5.2.1 5.2.2 5.2.3 Ambient Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Place of installation and space required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating in a compressed air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 5 5 5 ----------28 28 28 29 30
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 --- 31
6.1 6.2 6.3 6.4 6.5 6.5.1 6.5.2 6.5.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Report Transport Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install the Compressed Air Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting (option H1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling connection (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat recovery system connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 6 6 6 6 6 6 ----------------31 31 31 32 32 32 32 33
Initial Start---up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 --- 35

7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before Every Initial Start ---up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check Installation and Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the overload protection cut ---out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motor Protection Switch Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pour Cooling Oil into the Inlet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking Direction of Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initial Start ---up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting System Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 7 7 7 7 7 7 7 ------------------35 35 36 36 36 37 37 38 38
ii
Contents
Chapter --- page
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 --- 39
8.1 8.1.1 8.1.2 8.1.3 8.2 8.3 8.4 8.5 8.5.1 8.5.2 Switching On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching Off in an Emergency and Switching On Again . . . . . . . . . . . . . . . . . Remote On and Off Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching on and off with the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acknowledging and Resetting Warning and Alarm Messages . . . . . . . . . . . . . Resetting alarm messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resetting warning messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 8 8 8 8 8 8 8 8 --------------------39 39 39 40 40 40 41 41 42 42
Event Recognition and Fault Rectification . . . . . . . . . . . . . . . . . . . . . . 9 --- 43

9.1 9.2 9.3 Alarms (machine shut ---down, red LED blinking) . . . . . . . . . . . . . . . . . . . . . . . . 9 --- 43 Warning Messages (yellow LED blinking) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 --- 47 Miscellaneous faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 --- 50
10 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 --- 51
10.1 10.2 10.2.1 10.2.2 10.2.3 10.2.4 10.3 10.3.1 10.3.2 10.3.3 10.4 10.5 10.6 10.7 10.8 10.9 10.10 10.11 10.12 10.12.1 10.12.2 10.13 10.13.1 10.13.2 10.13.3 10.13.4 10.13.5 10.13.6 10.14 10.15 10.16 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resetting maintenance interval counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil change intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular service work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooler Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air cooling (option K1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter mat maintenance (option K3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling maintenance (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Heat Recovery Maintenance (option W2 / W3) . . . . . . . . . . . . . . . . . . . Air Filter Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter mat maintenance (control cabinet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric motor maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Safety Relief Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Overheating Safety Shutdown Function . . . . . . . . . . . . . . . . . . . . Venting the Machine Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking and Topping up the Cooling Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check cooling oil level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Topping up the cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the Cooling Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining the oil from the separator tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining the oil from the cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining the oil from the airend: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining the oil from the heat recovery system (option W1/W2/W3) . . . . . Filling with cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start the machine and carry out a test run. . . . . . . . . . . . . . . . . . . . . . . . . . . Oil filter maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the Oil Separator Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logging Maintenance Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 --------------------------------------------------------------51 52 52 53 53 54 55 55 55 56 57 57 59 59 61 61 62 62 64 64 65 66 68 68 69 70 70 71 71 72 74
iii
Contents
Chapter --- page
11 Spares, Operating Materials, Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 --- 75

11.1 11.2 11.3 11.4 11.5 Note the nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Maintenance Parts and Operating Materials . . . . . . . . . . . . . . . . . . . . Maintenance Contract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spare Parts for Service and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 11 11 11 ----------75 75 75 75 75
12 De ---commissioning, Storage and Transport . . . . . . . . . . . . . . . . . . . . 12 --- 82

12.1 12.2 12.3 12.4 12.4.1 12.4.2 12.5 De---commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transverse beams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 12 12 12 12 12 --------------82 82 83 83 83 84 84
13 Annex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 --- 85
13.1 13.1.1 13.1.2 13.1.3 13.1.4 Diagrams and Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pipeline and instrument flow diagram (P&I diagrams) . . . . . . . . . . . . . . . . . Pipeline and instrument flow diagram (option C1) . . . . . . . . . . . . . . . . . . . . Dimensional drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 13 13 13 ----------85 85 91 97 103
iv
Directory of Illustrations
Chapter --- page
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. 23 Fig. 24 Fig. 25 Fig. 26 Fig. 27 Fig. 28 Fig. 29 Fig. 30 Fig. 31 Fig. 32 Fig. 33 Fig. 34 Fig. 35 Fig. 36 Fig. 37 Fig. 38 Fig. 39
Three---phase star (wye); four wire; earthed neutral . . . . . . . . . . . . . . . . . . . . . . . Three---phase star (wye); three wire; earthed neutral . . . . . . . . . . . . . . . . . . . . . . Location of safety signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air ---cooled machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine mountings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter mat panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal heat recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIGMA CONTROL keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIGMA CONTROL indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation recommendation, dimensions [in] . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressed Air Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inlet valve oil filling port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching off in an emergency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acknowledging and Resetting Warning and Alarm Messages . . . . . . . . . . . . . . . Cleaning the cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooler filter mats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air filter maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control cabinet ventilator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressor motor maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan motor maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vent the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check cooling oil level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Topping up the cooling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the cooling oil, oil separator tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the cooling oil, oil cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the cooling oil, airend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turning the coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling oil changing, internal heat recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the Oil Separator Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transport by fork truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transport with lifting cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 --- 7 2 --- 7 3 --- 19 4 --- 20 4 --- 21 4 --- 23 4 --- 23 4 --- 23 4 --- 24 4 --- 26 4 --- 27 5 --- 29 6 --- 31 6 --- 32 6 --- 33 7 --- 37 7 --- 37 8 --- 39 8 --- 40 8 --- 41 10 --- 55 10 --- 56 10 --- 58 10 --- 59 10 --- 60 10 --- 60 10 --- 61 10 --- 63 10 --- 64 10 --- 65 10 --- 67 10 --- 68 10 --- 69 10 --- 69 10 --- 70 10 --- 71 10 --- 72 12 --- 83 12 --- 84
Table Directory
Chapter --- page
Tab. 1 Tab. 2 Tab. 3 Tab. 4 Tab. 5 Tab. 6 Tab. 7 Tab. 8 Tab. 9 Tab. 10 Tab. 11 Tab. 12 Tab. 13 Tab. 14 Tab. 15 Tab. 16 Tab. 17 Tab. 18 Tab. 19 Tab. 20 Tab. 21 Tab. 22 Tab. 23 Tab. 24 Tab. 25 Tab. 26 Tab. 27 Tab. 28 Tab. 29 Tab. 30 Tab. 31 Tab. 32 Tab. 33 Tab. 34 Tab. 35 Tab. 36 Tab. 37 Tab. 38 Tab. 39 Tab. 40 Tab. 41 Tab. 42
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ambient Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety relief valve setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitiy at rated pressure [CFM FAD] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sound Pressure Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressor motor data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan motor data (option K1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fan motor data (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling oil volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply 208V/3/60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply 230V/3/60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply 380V/3/60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply 460V/3/60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply 575V/3/60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling design data (30 F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water cooling design data (70 F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooler specification; water cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling Water Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat capacity (option W1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Quality Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General specification of the heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flow rate and heat available (option W2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flow rate and heat available (option W3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Danger zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIGMA CONTROL keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SIGMA CONTROL indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilation (option K1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilation (option K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checklist, installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alarm messages and actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning messages and actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous events (faults) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil change intervals lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil change intervals speciality lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regular service intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine maintenance parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 --- 3 2 --- 3 2 --- 3 2 --- 4 2 --- 4 2 --- 4 2 --- 4 2 --- 5 2 --- 5 2 --- 5 2 --- 5 2 --- 7 2 --- 8 2 --- 8 2 --- 8 2 --- 8 2 --- 9 2 --- 9 2 --- 9 2 --- 9 2 --- 10 2 --- 10 2 --- 11 2 --- 11 2 --- 11 2 --- 12 3 --- 17 3 --- 18 4 --- 27 4 --- 27 5 --- 29 5 --- 30 7 --- 36 9 --- 46 9 --- 49 9 --- 50 10 --- 53 10 --- 54 10 --- 54 10 --- 54 10 --- 74 11 --- 75
vi
Regarding this Document

1
1.1

Handling the Document
The service manual is part of the machine.
Keep the service manual in a safe place throughout the life of the machine. Pass the manual onto the next owner/user of the machine. Ensure that all amendments are entered in the manual. Enter details from the machine nameplate in the table in chapter 2 Technical Specifications.
1.2
Further Documents
Included with this Service Manual are documents intended to assist in safe and sure operation of the machine:
Request the supply of any missing documents from KAESER. Make sure you give the data from the nameplate.
1.3
Copyright
This service manual is copyright protected. Inquiries regarding use or duplication of the documentation should be referred to KAESER.
1.4
1.4.1
Symbols and Identifications

Warning notices Here is a notice warning of danger. DANGER Here are consequences of ignoring the warning notice. The word Danger indicates that death or severe injury can result from ignoring the notice.
Danger levels Warning notices indicate three levels of danger identified by the signal word under the danger symbol. Signal word DANGER WARNING CAUTION Meaning Warns of imminent threatening danger Warns of possible threatening danger Warns of a possibly dangerous situation Consequences of ignoring the warning Death or severe injury or serious damage to the machine is possible Death or severe injury or serious damage to the machine is possible Light injury or slight damage possible
certificate of acceptance / operating instructions for the pressure vessel manufacturers declaration or declaration of conformity in accordance with applicable directives SIGMA CONTROL Service Manual Make sure all documents are at hand and their contents understood.
Always read and diligently comply with warning notices.
1 --- 1

1.4.2 Miscellaneous notices and symbols
Here is a task to be carried out. This symbol identifies environmental protection measures.
This indicates important information.
1 --- 2
Technical Specification
2 Technical Specification
Model and important technical information is to be found on the machine nameplate. The nameplate is found inside the machine. It is fixed to the outside of the control cabinet. Please transfer data from the nameplate. Model Part no. Year Serial no. psig cfm Voltage Hz/RPM Package FLA Phase HP Wiring Diagram FOR SERVICE, REFER TO EQIPMENT NUMBER Tab. 1 Nameplate A summary of the included options helps to relate the service manual information to your machine. Please enter details of options. Option Air cooled Water cooled Filter mat panels Machine mountings Prepared for heat recovery Internal heat recovery T= 25K Internal heat recovery T= 55K Modulation control Transformer power supply for refrigeration dryer Tab. 2 Options

Code K1 K2 K3 H1 W1 W2 W3 C1 T2
Exists
2.1
Weight
Maximum weights are shown. Actual weights of individual machines are dependent on equipment fitted. CSD 100 4235 Machine weights CSD 125 4455
Weight [lb] Tab. 3
2 --- 3
2.2 Temperature
Minimum cut ---in temperature [ F] Typical airend discharge temperature during operation [ F] Max. airend discharge temp. (automatic shut ---down) [ F] Tab. 4 Machine temperatures CSD 100 40 167 --- 200 230 CSD 125 40 167 --- 200 230
2.3
Ambient Conditions
Maximum elevation [ft] Ambient temperature [ F] Inlet air / cooling air temperature [ F] Humidity of the inlet air at 100 100 90 F [%] Humidity of the inlet air at 50 50 113 F [%] * Higher elevation permissible only after consultation with the manufacturer Tab. 5 Ambient Conditions CSD 100 3000 40 115 40 115 CSD 125 3000 40 115 40 115
2.4
Pressure
See nameplate for maximum working pressure. Maximum working pressure [psig] 125 160 217 Safety relief valve setting Blow--- off setting of the safety relief valve [psig] CSD 100 155 230 230 CSD 125 155 230 230
Tab. 6
2.5
Free Air Delivery (FAD)

Rated pressure [psig] CSD 100 110 506 125 503 145 420 160 417 175 348 190 345 217 337 Tab. 7 Capacitiy at rated pressure [CFM FAD] CSD 125 584 581 498 494 414 411 406
2 --- 4
2.6 Sound Pressure Level
Operational state
under load at rated speed, rated delivery and rated pressure.
Measuring conditions:
Free---field measurement to CAGI/PNEUROP PN8 NTC 2.3 at 1 m distance CSD 100 73 CSD 125 74
Sound pressure level (60Hz) [dB(A)] Tab. 8 Sound Pressure Level
2.7
2.7.1
Motor and Performance

Compressor motor: CSD 100 100 3580 TEFC 2000 CSD 125 125 3582 TEFC 2000
Rated power [Hp] Rated speed [rpm] Enclosure protection Motor bearing greasing [operating hours] Grease requirement, each bearing [oz]* * Transfer data from motor nameplate to the table Tab. 9 Compressor motor data
2.7.2
Fan Motor Air cooling (option K1) CSD 100 3 1170 TEFC 2000 CSD 125 3 1170 TEFC 2000
Rated power [Hp] Rated speed [rpm] Enclosure protection Motor bearing greasing [operating hours] Grease requirement, each bearing [oz]* * Transfer data from motor nameplate to the table Tab. 10 Fan motor data (option K1) Water cooling (option K2)
Rated power [Hp] Rated speed [rpm] Enclosure protection Tab. 11 Fan motor data (option K2)
CSD 100 0.13 2700 TEFC
CSD 125 0.13 2700 TEFC
2 --- 5
2.8 Cooling oil
Ordering: see Spare Parts, Operating Materials, Service chapter 11. Lubrication of an air compressor is essential to reliable operation. Carbon and varnish can form in compressor oils. These deposits block the flow of lubricant and cause excessive wear and failure of moving parts. Contamination of the lubricant can allow the formation of acids, causing extensive internal corrosion. Water may be condensed decreasing the lubricity. Lubricants in rotary compressors do much more than lubricate. During the compression process, it acts as a sealant in the airend which is important for maximum efficiency. The lubricant also absorbs much of the heat of compression to cool the airend and reduce the temperature of the compressed air. Its not enough that a compressor cooling oil lubricates well, it must stand up to the heat, pressure and contaminants that are present in every air compressor. 2.8.1 General Information KAESER synthetic lubricants should be stored in a protected location to prevent contamination. Do not re---use drums; flush and send to reconditioner. Although the KAESER synthetic is not highly flammable, it will burn. While KAESER synthetic compressor oil is less flammable than equal viscosity mineral oils, it cannot be classified as a fire---resistant fluid. It has a flash point above 460 F. Since the user has total control over the conditions of the compressor lubricant, he assumes total responsibility for its safe usage. Material Safety Data Sheets are available for each lubricant from your KAESER authorized distributors. Regardless of the lubricant selected, the KAESER Sigma lubricants will separate readily from water. If condensate occurs it can easily be removed. Let the compressor sit so that any water can drain back to the separator tank and separate to the bottom. See chapter 10.13 proper draining procedure. KAESER has several lubricants available that are specially formulated to match these demands. They feature excellent lubricity, outstanding demulsibility (ability to separate from water), and long life. M --- SERIES SEMI --- SYNTHETIC LUBRICANTS

M---Series SIGMA compressor cooling oils are the highest quality petroleum lubricants. M---460 is specially blended to provide reliable performance in KAESER screw compressors.
S--- SERIES SYNTHETIC LUBRICANTS S---Series SIGMA compressor oils are formulated from the most advanced synthetic lubricants. These synthetic lubricants begin as high quality petroleum feed stock. They are then refined, processed and purified into fluids with very consistent molecular structure. These oils are carefully blended to produce extremely consistant lubricants with superior properties. SIGMA synthetic lubricants feature all the advantages of both PAO and diester fluids. S---460 lubricant is recommended for compressors operating in ambient temperatures between 40 F and 105 F.
Specialty KAESER LUBRICANTS S---680 lubricant may be used when ambient temperatures are always between 70 F and 105 F. FG---460 synthetic hydrocarbon based food grade lubricant is designed for use in rotary screw compressors in the application where incidental food contact may occur
2 --- 6
with the discharge air. This lubricant meets the requirements of the FDA Regulation 21 CFR 178.3570 and is USDA H ---1 approved and NSF certified. FG---460 is approved for canning, food packing, meat and poultry processing and other applications where incidental food contact may occur. 2.8.2 Cooling Oil Quantity CSD 100 14.5 11.4 1.3 CSD 125 14.5 11.4 1.3 1.9 1.2
Total charge [gal] (option K1) Total charge [gal] (option K2) Top ---up volume [gal] (minimum --- maximum Additional volume [gal] (option W2) 1.9 Additional volume [gal] (option W3) 1.2 Additional volume [gal] (option W1) * * Input the additional volume corresponding to your heat recovery system. Tab. 12 Cooling oil volumes
2.9
Electrical Connections
See electrical diagrams in chapter 13.1.4.
2.9.1
Power supply The machine is designed for an electrical supply according to National Electric Code (NEC) NEC---670, particulary NFPA 79, section 5.7. In the absence of any user ---specified alternatives, the limits given in these standards must be adhered to. Consult manufacturer for any other specific power supply. Three --- phase Do NOT operate package on any unsymmetrical power supply. Also do NOT operate package on power supplies like, for example, a three---phase (open) delta or three---phase star with non ---earthed neutral.
Fig. 1
Three ---phase star (wye); four wire; earthed neutral
Fig. 2
Three ---phase star (wye); three wire; earthed neutral
The machine requires a symmetrical three---phase power supply transformer with a WYE configuration output as shown in Fig. 1 and Fig. 2. In a symmetrical three phase supply the phase angles and voltages are all the same. Other power supplies are not suitable. Please contact authorized KAESER distributor for options.
2 --- 7
2.9.2 Power supply specifications The following multi---strand copper core wires are given according to 2002 NEC 310 ---15, Table 310 ---16 for 40 C ambient temperature. If other local conditions prevail, like for example high temperature, the cross section should be checked and adjusted according to 2002 NEC 110 ---14 , 220 ---3,310 ---15, Table 310 ---16, 430 ---6, 430 ---22, 430 ---24 and other local codes. Dual element time delay fuses are selected according to 2002 NEC 240 ---6,430 ---52 and tables 430 ---52, 430 ---148 and 430 ---150. We strongly suggest using a separate copper conductor for the equipment GROUNDING. NEC Table 250.122 will point out the minimum size, however, we recommend a ground conductor the same size as the power leads, if local codes allow. Rated power supply 208V 10%, 3 --- ph, 60Hz

Pre---fuse [A] Supply Consumption [A] (Option K1) Consumption [A] (Option K2) Tab. 13 Supply 208V/3/60Hz
CSD 100 450 2x 4xAWG4/0 320 310
CSD 125 500 2x 4xMCM250 354 345
Rated power supply 230V 10%, 3 --- ph, 60Hz CSD 100 400 2x 4xAWG4/0 288 279 CSD 125 450 2x 4xAWG4/0 320 311
Pre---fuse [A] Supply Consumption [A] (Option K1) Consumption [A] (Option K2) Tab. 14 Supply 230V/3/60Hz

Rated power supply 380V 10%, 3 --- ph, 60Hz Pre---fuse [A] Supply Consumption [A] (Option K1) Consumption [A] (Option K2) Tab. 15 Supply 380V/3/60Hz Rated power supply 460V 10%, 3 --- ph, 60Hz Pre---fuse [A] Supply Consumption [A] (Option K1) Consumption [A] (Option K2) Tab. 16 Supply 460V/3/60Hz Rated power supply 575V 10%, 3 --- ph, 60Hz Pre---fuse [A] Supply CSD 100 150 4xAWG2/0 CSD 125 175 4xAWG3/0 CSD 100 200 4xAWG4/0 146 142 CSD 125 225 4xAWG4/0 160 157 CSD 100 250 4xMCM250 175 169 CSD 125 250 4xMCM300 195 190
2 --- 8
CSD 100 115 112 CSD 125 128 125
Consumption [A] (Option K1) Consumption [A] (Option K2) Tab. 17 Supply 575V/3/60Hz
2.10
2.10.1
Water cooling (option K2)

Design data Cooling water temperature rise 30 F CSD 100 90 26.4 15 CSD 125 90 31.9 20
Max. permissible inlet temperature [ F] Min. cooling water flow [gpm] Water pressure drop [psig] Tab. 18 Water cooling design data (30 F) Cooling water temperature rise 70 F
Max. permissible inlet temperature [ F] Min. cooling water flow [gpm] Water pressure drop [psig] Tab. 19 Water cooling design data (70 F) Cooler specification Material of manufacture Solder Maximum working pressure (cooling water end) [psig] Unsuitable cooling medium
CSD 100 50 8.8 7
CSD 125 50 10.6 7
1.4401 Copper 145 Seawater Consult KAESER before using cooling water solutions 158
Max. permissible discharge temperature [ F] Tab. 20 Cooler specification; water cooling 2.10.2 Cooling Water Quality
Do not use the cooling water as drinking water. If a leak occurs, oil can contaminate the cooling water. Measures for cooling water treatment and filtration are essential and must be carried out. The addresses of companies specializing in the analysis of cooling water and supplying suitable equipment for the its treatment can be obtained from KAESER on request. To avoid operating breakdowns from a corroded or clogged cooler, the cooling water must meet certain minimum requirements:
2 --- 9
pH value Hardness [ dH] Chloride (Cl) [mg/l] Free chlorine gas (Cl2) [mg/l] Sulphate (SO3) [mg/l] Dissolved iron (Fe) [mg/l] Hydrogen carbonate (HCO3) [mg/l] Sulphate (SO4) [mg/l] HCO3 / SO4 Electrical conductivity [ S/cm] Ammonia (NH3) [mg/l] Dissolved magnesium (Mn) [mg/l] Dissolved aluminium (Al) [mg/l] Nitrate (NO3), dissolved [mg/l] Hydrogen sulphate (SO2) [mg/l] Free aggressive carbon dioxide (CO2) [mg/l] Glycol [%] Solids (particle size) [mm] Algae Tab. 21 Cooling Water Quality 7.5 to 9.0 4.0 ---8.5 < 150 < 1 < 1 < 0.2 70 ---300 < 70 > 1 10 ---500 < 2 < 0.1 < 0.2 < 100 < 0.05 < 5 < 50 < 0.1 not permissible
2.11
2.11.1
Heat Recovery
Prepared for heat recovery (option W1) Connections for an external heat recovery system are provided. Heat capacity CSD 100 40.3 145 34669 CSD 125 49.4 178 42511
Max. heat capacity available [kW] Max. heat capacity available [MJ/h] Max. heat capacity available [kcal/h] Tab. 22 Heat capacity (option W1) 2.11.2 Internal Heat Recovery (option W2 / W3)
A soldered, plate heat exchanger is installed for heat recovery. Generally water is used as the heat transfer medium. This must conform to the specification given below. The water may not be used as drinking water. If a leak occurs, oil can contaminate the water. The manufacturer should be consulted before another type of heat transfer medium is used. Water Quality Specification pH value Hardness [ dH] 7.5 to 9 4.0 ---8.5
2 --- 10
Chloride (Cl)* [mg/l] Free chlorine gass (Cl2) [mg/l] Sulphate (SO3) [mg/l] Dissolved iron (Fe) [mg/l] Hydrogen carbonate (HCO3) [mg/l] Sulphate (SO4) [mg/l] HCO3 / SO4 Electrical conductivity [ S/cm] Ammonia (NH3) [mg/l] Dissolved magnesium (Mn) [mg/l] Dissolved aluminium (Al) [mg/l] Nitrate (NO3), dissolved [mg/l] Hydrogen sulphate (SO2) [mg/l] Free aggressive carbon dioxide (CO2) [mg/l] Glycol [%] Solids (particle size) [mm] Algae Tab. 23 Water Quality Specification
< 150 < 1 < 1 < 0.2 70 ---300 < 70 > 1 10 ---500 < 2 < 0.1 < 0.2 < 100 < 0.05 < 5 < 50 < 0.1 not permissible
If the heat transfer medium outlet temperature is to be kept constant, the user must install an appropriate regulating device. Heat Exchanger Specification CSD 100 145 CSD 125 145 < 1.5 1.4401 Cu 210
Maximum working pressure of the heat transfer medium [psig] Pressure drop [psig] < 1.5 Plate material 1.4401 Solder Cu Maximum permissible temperature of 210 the heat transfer medium [ F] Tab. 24 General specification of the heat exchanger
Flow rate and heat capacity by heating from 110 F to 160 F (equivalent to T= 25 K), (option W2) CSD 100 Flow rate [gpm] 9.7 Max. heat capacity available [kW] 40.3 Max. heat capacity available [MJ/h] 145 Max. heat capacity available [kcal/h] 34669 Tab. 25 Flow rate and heat available (option W2) CSD 125 11.9 49.4 178 42511
Flow rate and heat capacity by heating from 60 F to 160 F (equivalent to T= 55 K), (option W3) CSD 100 4.4 40.3 CSD 125 5.3 49.4
Flow rate [gpm] Max. heat capacity available [kW]
2 --- 11
CSD 100 Max. heat capacity available [MJ/h] 145 Max. heat capacity available [kcal/h] 34669 Tab. 26 Flow rate and heat available (option W3) CSD 125 178 42511
2 --- 12
Safety and Responsibility

3 Safety and Responsibility
Disregard of these instructions can result in serious injury.
DANGER
Read the service manual carefully and pay attention to its contents.
This machine is manufactured to the latest engineering standards and acknowledged safety regulations. Nevertheless, risk of injury and death for the user and other parties and damage to the machine and other property can arise from its use. Use this machine only if it is in a technically perfect condition and only for the purpose for which it is intended; observe all safety measures and the instructions in the service manual. In particular, immediately rectify (have rectified) any faults that could be detrimental to safety.
3.1
Proper Use
The machine is intended solely for industrial use in generating compressed air. Any other use is considered incorrect. The manufacturer is not liable for any damages resulting from such unspecified use or application. The risk involved in such unspecified use is taken solely by the user. Specified use also includes compliance with the instructions in this manual.
3.2
Improper Use
3.3
Users Responsibilities
The basic principle: observe approved safety regulations Observe the relevant regulations during installation, operation, maintenance and repair of the machine. These are, for example, valid national laws and safety and accident prevention regulations.
3.3.1
Qualified personnel Ensure that operating, installation and maintenance personnel are qualified and authorized for their tasks. These are people who, by virtue of their training, knowledge and experience as well as their knowledge of the prevailing conditions, can assess the work to be done and recognize the possible dangers involved.
Never direct compressed air at persons or animals. Do not use untreated compressed air for breathing purposes. Do not use untreated compressed for any application that will bring it into direct contact with foodstuffs. Cooling air, warmed after passing through the machine, may be used for heating purposes but only when it poses no health risk to humans or animals. If necessary, the warmed cooling air should be treated to render it harmless. Do not allow the machine to take in toxic, acidic, flammable of explosive gases or vapors. Do not operate the machine in areas in which specific requirements with regard to explosion protection are applied.
3 --- 13

Operating personnel Authorized operating personnel:
must be adult, must be conversant with and adhere to the safety instructions and sections of the service manual relevant to operation of the machine, must have received adequate training and authorisation to operate electrical and compressed air devices must have adequate training and authorisation to operate refrigeration equipment (for machines with refrigeration dryers).
Installation and maintenance personnel Authorised installation and maintenance personnel:
3.3.2
Adhere to inspection schedules and accident prevention regulations. The machine is subject to local inspection schedules.
3.4
Safety Devices
Do not change, bypass or disable safety devices. Do not remove or obliterate labels and notices. Ensure that labels and notices are clearly legible. More information on safety devices is contained in chapter 4 Design and Function, section 4.5 Safety Devices.
3.5
Hazards
Fundamentals: observe the accepted safety regulations Observe safety regulations at all times when working on the machine. Examples of these are requirements and national regulations concerning safety and accident prevention.
must be adult, must have read, be conversant with and adhere to the safety instructions and sections of the service manual applicable to installation and maintenance. must be fully conversant with the safety concepts and regulations of electrical and compressed air engineering, must be conversant with safety concepts and regulations relating to refrigeration equipment (for machines with refrigeration dryers), must be able to recognize the possible dangers of electrical and compressed air devices and take appropriate measures to safeguard persons and property, must be able to recognize the possible dangers of refrigeration devices and take appropriate measures to safeguard persons and property (for machines with refrigeration dryers), must have received adequate training and authorization for the safe installation and maintenance on this machine.
3 --- 14

3.5.1 Danger from electricity Voltage! DANGER Touching electrically energized components can cause serious injury or death.
Isolate completely from the power supply (all conductors) (switch off at the main isolator) Ensure the supply cannot be switched on again (lock off). Check that no voltage is present.
Volt ---free contacts may be under power from an external source even when the machine is isolated from the main power supply. Before the machine is switched on for the first time the user must provide and check measures to guard against electric shock by direct or indirect contact. 3.5.2 Dangers from compressed air Danger from compressed air quality The compressed air from this machine may not be used without taking appropriate precautions:
as breathing air for processing foodstuffs. Unsuitable compressed air!
DANGER
Injury and/or contamination can result from breathing compressed air.
Danger from compressive forces Compressed air is a contained force. Uncontrolled release of this force can cause serious injury or death. Uncontrolled pressure release! WARNING Serious injury or death can result from loosening or opening components under pressure.
Never breath untreated compressed air! Air from this compressor must meet OSHA 29CFR1910.134 and FDA 21CFR178.3570 standards, if used for breathing or food processing. Use proper compressed air treatment. Food grade coolant must be used for food processing.
Close shut ---off valves or otherwise isolate the machine from the compressed air system to ensure that no compressed air can flow back into the machine. De---pressurize all pressurized components and enclosures. Check all machine hose connectors with a hand ---held pressure gauge to ensure that all read zero.
3 --- 15

Welding, heat treatment and mechanical modifications to pressure components (e.g. pipes and vessels) is not permitted as this influences the components pressure resistance. The safety of the machine is then no longer ensured. Use only genuine KAESER spares for parts subject to pressure. The use of unsuitable parts may adversely influence the safe working of the machine. Extension or modification of the compressed air system If a compressed air installation is extended or modified check the blow ---off capacity of the safety relief valves on air receivers and pipelines before installing the new machines. Any safety relief valves of insufficient capacity must be replaced with larger models. 3.5.3 Danger from released spring force Springs under tension or compression contain force. Uncontrolled release of this force can cause serious injury or death. Minimum pressure/check valve, safety relief valve and inlet valve are heavilly spring--- loaded. WARNING Fatal injury may occur from incorrect opening of spring ---loaded components.
Do not open (dismantle) valves. Contact authorized KAESER distributor.
3.5.4
Further dangers Handling cooling and lubricating fluids
Avoid contact with skin and eyes. Do not inhale oil mist or vapor. Do not eat or drink while handling cooling and lubricating fluids. Fire, open flame and smoking are strictly forbidden.
Conversion or modification of the machine Conversion or modification of the machine is not permitted as this can influence function and safe working. Fire hazard When welding is taking place on or near the machine take adequate measures to ensure that no parts of the machine or any oil vapours can ignite because of sparks or heat. 3.5.5 Danger zones The table gives information on the zones dangerous to personnel. Only authorized personnel may enter these zones. Activity Transport Danger zone 10 ft radius from the machine Authorized personnel Installation or transport personnel. All personnel excluded during transport. Beneath the lifted machine. All personnel excluded!
3 --- 16

Activity Installation Danger zone Within the machine. 3 ft radius of the machine and power lines. Operation Maintenance 3 ft radius from the machine 6 ft radius from the cooling air discharge. Within the machine. 3 ft radius from the machine Tab. 27 Danger zones Maintenance personnel Operating personnel Authorized personnel Installation personnel
3.6
Safety Signs
The table lists the various safety signs used and their meanings. The diagram shows the positions of the signs on the machine. Location 8 Sign Meaning Voltage! Touching electrically live components can cause serious injury or death. Isolate completely from power supply (all conductors) and ensure the supply cannot be switched on again (lock off). Check that no voltage is present. Automatic starting Servere injury could result from rotation components, electrical voltage and air pressure. Isolate completely from power supply (all conductors) and ensure the supply cannot be switched on again (lock off). Check that no voltage is present. Compressed air qualitiy Injury and/or contamination can result from breathing compressed air. Contamination of food can result from using untreated compressed air for food processing. Never breath untreated compressed air! Air from this compressor must meet OSHA 29CFR1910.134 and FDA 21CFR178.3570 stamdards, if used for breathing or food processing. Use proper compressed air treatment. Food grade coolant must be used for food processing. Rejected parts Severe injury, especially of the eyes, could result while the fan is rotating. Prevent all materials from falling into the fan guard. Never work over the running machine. Hot surface can cause burns Let the machine cool down. Wear long ---sleeved garments (not synthetics such as polyester) and protective gloves.

11
12
13
3 --- 17

Location 16 Sign Meaning Wrong cooling oil level Risk of machine defects or rising oil consumption (oil content for pure air). Check cooling ---oil level regularly. Run the machine only with proper cooling ---oil level. Voltage! Touching electrically live components can cause serious injury or death. Isolate completely from power supply (all conductors) and ensure the supply cannot be switched on again (lock off). Check that no voltage is present. Pressure and spring force Serious injury or death can result from loosening of opening component that is under pressure and heavily spring loaded. Never open (dismantle) valve. Contact authorized KAESER distributor. Compressed air Serious injury or death can result from loosening or opening component under pressure De---pressurize all pressurized components and enclosures. Secure that machine keeps de---pressurized. Check that machine is de---pressurized. Loud noise and oil mist when safety relief valve opens Ear damage and burns can result. Wear ear protection and protective cloths. Close all maintenance doors and cover panels. Rotating coupling Severe injury could result from touching the coupling while it is rotating. Nerver switch the machine on without the guard in place over the coupling. Isolate completely from power supply (all conductors) and ensure the supply cannot be switched on again (lock off). Risk of fire or electric shock If the interrupter has tripped current ---carrying components of the controller should be examined and replaced if damaged to reduce the risk of fire or electric shock. Risk of fire or electric shock To maintain overcurrent short ---circuit, and ground ---fault protection, the manufacturesre instructions for setting the interrupter must be followed to reduce the risk of fire or electric shock. Safety signs

19
23
24
25
26
27
28
Tab. 28
3 --- 18
Fig. 3
Location of safety signs
3.7
3.7.1
Emergencies
Fire supression Suitable extinguishing media:
foam powder carbon dioxide sand or earth powerful water jet
Unsuitable or unsafe extinguishing media:
3.7.2
Cooling oil Skin contact: wash off immediately rinse thoroughly with lukewarm water and seek medical assistance. Eye contact: If necessary, request a copy of the safety data sheet for KAESER lubricants.

3.8
Environmental Protection
Do not allow cooling oil to escape to the environment or into the sewage system. Store and dispose of used materials and replaced parts in accordance with local environment protection regulations. Observe national regulations. This applies particularly to parts contaminated with cooling oil.
3 --- 19
Design and Function

4
4.1
4.1.1
Design and Function

Machine Overview
Cabinet
Fig. 4
Cabinet
1 Control cabinet door 2 Latch 3 Removable panel The cabinet, when closed, serves various purposes:

Sound damping Protection Cooling air flow control
Safe and reliable operation can only be ensured with the cabinet closed. Latches are released by a key supplied with the machine. Access doors are hinged to swing open, removable panels must be lifted off.
4 --- 20
Design and Function

4.1.2 Function Items in brackets [ ] correspond to the Pipe and Instrument Flow Diagram (P & I Diagram) in chapter 13.1.1. An air ---cooled machine serves to illustrate function.
Fig. 5 1 2 3 4 5
Air ---cooled machine 6 7 8 9 Control cabinet Oil separator tank [6] Air filter [1] Oil/air cooler [11/13]
Inlet valve [2] Coupling [5] Compressor motor [3] Oil filter [10] Airend [4]
Compressor Atmospheric air is cleaned as it is drawn in through the filter (8). The air is then compressed in the airend (5). The airend is driven by an electric motor (3). Cooling oil is injected into the airend. It lubricates moving parts and forms a seal between the rotors themselves and between them and the airend casing. The cooling effect directly within the compression chamber ensures a low airend discharge temperature. Cooling oil is recovered from the compressed air in the oil separator tank (7) and is then cooled in the oil cooler (9). The oil then flows through the filter (4) and back to the point of injection. Air pressure within the machine keeps the oil circulating and therefore a separate pump is not necessary. A thermostatic valve maintains optimum oil temperature. Compressed air, freed of its oil content in the separator tank (7), flows through the minimum pressure/check valve into the aftercooler (9). The minimum pressure/check valve ensures there is always sufficient air pressure to maintain cooling oil circulation. The aftercooler brings down the compressed air temperature to 5 to 10 K above ambient. Most of the moisture carried in the air is removed in the aftercooler.
4 --- 21
Design and Function

4.2 Volt---free Contacts
Volt ---free contacts are provided for passing messages. Information on location, load and type of message is to be found in the electrical diagram. If the volt ---free contacts are connected to an external power source they may be under power even when the machine is isolated from the supply.
4 --- 22
Design and Function

4.3
4.3.1
Options
Machine mountings (option H1) The machine mountings enable the machine to be anchored to the floor.
Fig. 6 4.3.2
Machine mountings
Filter mat panels (option K3) Mats filter the cooling air and keep the cooler surface clean.
Fig. 7 1 4.3.3
Filter mat panel
Cooling air filter mat
Water cooling (option K2) Plate heat exchangers in stainless steel are used for water ---cooled machines.
Fig. 8 1 2 4.3.4
Water cooling 3 4 Cooling water connection Cooling water connection
Oil cooler [11] Compressed air aftercooler [13]
Heat recovery External heat recovery (option W1) Connections are provided and bridged.
4 --- 23
Design and Function

An external heat recovery system can be retro ---fitted at any time. Internal heat recovery (option W2 / W3) A plate heat exchanger (1) is installed for heat recovery.
Fig. 9 1
Internal heat recovery
Plate heat exchanger [26]
4.4
4.4.1
Operating States and Control Modes

Operating states There are three operating states:
LOAD: the inlet valve is open. The airend delivers compressed air to the system. The compressor motor runs under full load. IDLING: The inlet valve is closed. The minimum pressure/check valve shuts off the oil separator from the air system. The oil separator tank is vented. A small volume of air circulates through the bleed hole in the inlet valve, through the airend and back to the inlet valve via the venting valve. The compressor motor runs without load and draws little current. STANDSTILL: The inlet valve is closed. The minimum pressure/check valve shuts off the oil separator from the air system. The oil separator tank is vented. The compresor motor is stopped. MODULATION CONTROL (option C1): The proportional controller continuously varies the degree of opening of the inlet valve, and thereby the delivery rate of the compressor, in response and in proportion to the air demand. The airend delivers compressed air to the system. The load and power consumption of the compressor motor rises and falls with the air demand. The regulating valve is factory set. Consult with KAESER Service before changing.
4.4.2
Controller Operation Using the selected control mode, the controller switches the compressor between its various operational states in order to maintain system pressure between the set minimum and maximum values. According to the individual compressed air demand one of the various control modes available will provide the optimum duty cycle for the machine.
4.4.3
Control Modes The controller can operate in the following modes:
DUAL VARIO QUADRO
4 --- 24
Design and Function

DUAL In the DUAL control mode, the compressor is switched back and forth between LOAD and IDLE to maintain system pressure between the set minimum and maximum values. When the maximum pressure is reached the machine switches to idle running. When the preset idling time has elapsed the machine is STOPPED. The shorter the idling time setting, the sooner and more frequently the motor is stopped. VARIO The VARIO control mode is an extension of DUAL control. The difference from DUAL being that under VARIO control the idling time is automatically increased or decreased corresponding to the increased or decreased switching frequency of the drive motor. QUADRO In QUADRO control mode the machine switches from LOAD to IDLE during periods of high air demand and directly from LOAD to STANDSTILL during periods of low air demand. This mode of control requires two pre---set time periods: the running time and the idle/ standstill time. The shorter these time settings, the sooner and more frequently the motor is stopped. 4.4.4 Modulation Control (option C1) The modulating control mode is an extension of DUAL control. The difference being that, in this mode, the delivery of the compressor is steplessly varied within the control range of the machine.
Increasing air demand
The machine operates between PARTIAL LOAD and LOAD.
Falling air demand
The machine operates between PARTIAL LOAD, IDLE RUNNING and STANDSTILL.
4.5
Safety Devices
The following safety devices are provided and may not be changed:

EMERGENCY STOP button The EMERGENCY STOP button shuts down the compressor immediately. The motor remains still. The pressure system is vented. Safety relief valve The safety relief valve protects the system from excessive pressure. This is factory set. Housing and covers for moving parts and electrical connections. Protection from accidental contact.
4 --- 25
Design and Function

4.6 SIGMA CONTROL Keys and Indicators
Fig. 10
SIGMA CONTROL keys
Symbol
Item Description 1 2 3 ON (I) OFF (0) Operating mode: Clock Operating mode: Remote control Operating mode: LOAD / IDLE Arrow key Arrow key Escape
Function Switch the machine on. Programmed operating mode is active. Switch the machine off. Switching clock ---control on and off. The LED lights when the machine is under clock control. Switching remote control on and off. The LED illuminates when the machine is under remote control. Toggles the machine between LOAD and IDLE. Scrolls down menu. Reduces a parameter value. Scrolls menu up. Increases a parameter value. Returns to the next higher menu level. Exits the edit mode without saving. Returns to the main menu when held down at least 10 seconds. Only affects the message in the third line of the display (12). Returns to the selected submenu. Saves and leaves the edit mode.
5 6 7 8
Return/enter/save key
4 --- 26
Design and Function

Symbol Item Description 10 Events and information key Function Displays the event memory. Selection from every menu. Returns together with esc key (8). Acknowledges (re---sets) messages and resets the event memory (if permitted).
11 Tab. 29
Acknowledge (reset) key
SIGMA CONTROL keys
Fig. 11 Symbol
SIGMA CONTROL indicators Item Description 12 13 14 15 Display Alarm Communication Service/warning LED Controller power ON LOAD Function Alphanumeric display with 4 lines. Blinks red when an alarm occurs. Lights continuously when acknowledged. Lights red if communication via the Profibus is interrupted. Blinks yellow for: --- maintenance work required --- warning message Lights green when the power supply to the controller is switched on. Lights green when the machine is in the operating state LOAD Lights green when the machine is in the IDLE mode. Blinks green if the manualLOAD/IDLING changeover key (5) is used. The machine is switched on.
16 17
18
Operating mode IDLE Machine ON
19 Tab. 30
SIGMA CONTROL indicators
4 --- 27
Installation and Operating Conditions

5
5.1

Ambient Conditions
There must be no open flames or sparks at the place of installation. Any welding work carried out on the equipment must not cause a fire hazard through flying sparks or excessive temperature. The machine is not explosion ---proof. Do not operate in areas in which specific requirements with regard to explosion protection are applied. Clean inlet air with no damaging contaminants. Inlet air free of explosive or chemically unstable gas or vapor. Inlet air free of acid ---forming substances, particulatly ammmonia, chlorine or hydrosulphide. Ambient temperature must be acceptable and stable. The airend discharge temperature must remain constant to prevent the build ---up of condensate. Suitable fire extinguishing material must be readily available.
5.2
5.2.1
Installation Conditions
Place of installation and space required The spacings given are recommended and ensure unhindered access to all machine parts. Please consult KAESER if they cannot be achieved.
The floor must be level, firm and able to bear the weight of the equipment. If installed outdoors, the equipment must be protected from cold temperature, direct sunlight, dust and rain. Allow sufficient distance from any wall to enable unhindered maintenance work.
5 --- 28
Fig. 12 A B Z 5.2.2
Installation recommendation, dimensions [in]
Exhaust fan Exhaust air duct Inlet air opening
Ventilation Values given are minimum guidelines. If the inlet aperture is insufficient a dangerous vacuum can be created in the compressor room.
Ensure that the volume of air flowing into the compressor room is at least equivalent to that being removed from it by the machine and exhaust fan. Make sure that the machine and exhaust fan can only operate when the inlet aperture is actually open.
Option K1: CSD 100 20 14714 39 3/8 x 39 3/8 CSD 125 24 17657 39 3/8 x 39 3/8
Inlet opening [sq.ft.] Forced ventilation with exhaust ventilator: Flow rate [cfm] at 0.4 in wc Exhaust air duct: Dimensions [in] Tab. 31 Ventilation (option K1)
5 --- 29

Option K2: CSD 100 3.2 1766 27 1/2 x 27 1/2 CSD 125 3.2 1766 27 1/2 x 27 1/2
Inlet opening [sq.ft.] Forced ventilation with exhaust ventilator: Flow rate [cfm] at 0.4 in wc Exhaust air duct: Dimensions [in] Tab. 32 Ventilation (option K2) Exhaust ducting
Consult the manufacturer on the design of the ducting, length, number of bends, etc. Further information on exhaust air ducts can be found in chapter 13.1.3. 5.2.3 Operating in a compressed air system When the machine is connected to an air system, the operating pressure must not exceed 230 psig. Initial filling of a fully vented air system generally creates a very high rate of flow through air treatment devices. These conditions are detrimental to correct air treatment. Air quality can be degraded. To ensure maintenance of desired air quality when filling a vented air system we recommend the installation of an air main charging system. Please contact KAESER for assistance in selecting and installing an air main charging system.
5 --- 30
Installation
6
6.1
Installation
Safety
Voltage! DANGER Contact with live electric components can cause serious injury or death.
Isolate completely from the mains supply (switch off the main isolator) Ensure that the power supply cannot be switched on again (lock off). Check that no voltage is present.
Uncontrolled pressure release! WARNING Serious injury or death can result from loosening or opening components under pressure.
Minimum pressure/check valve, safety relief valve and inlet valve are heavily spring--- loaded. WARNING Fatal injury may occur from incorrect opening of spring ---loaded components.
Installation work may only be carried out by authorized personnel! All functioning parts are factory set. Changes may not be made without the permission of the manufacturer.
6.2
Report Transport Damage
Check the machine for visible and hidden transport damage. Inform the carrier and the manufacturer in writing of any damage.
6.3
Install the Compressed Air Connection

Pre --- condition: air system completely vented.
Fig. 13 1 2
Compressed Air Connection
Axial compensator or flexible hose Shut ---off valve
De---pressurize all pressurized components and enclosures.
Do not open or dismantle valves. Contact authorized KAESER distributor, if a fault occurs.
6 --- 31
Installation
Shut ---off valve (2) to be installed by the user in the connection line. Make the compressed air connection with a flexible hose (1) or an axial compensator (1).
6.4
Electrical Connection
Main power supply and overcurrent protection must be installed by a qualified electrician in accordance with NEC, OSHA, and any applicable local codes. Use wire conductor dimensions and fuse ratings in accordance with local regulations. Guide values are given in chapter 2.9.
Before initial start--- up
6.5
6.5.1
Options
Mounting (option H1) If the machine is supplied with mountings, these can be used to anchor it to the floor. Details of the mounting holes are contained in the dimensional drawing in chapter 13.1.3.
6.5.2
Water cooling connection (option K2) The dimensional drawing in chapter 13.1.3 gives the flow direction, size and position of the cooling water connection ports. Use connecting lines made of the appropriate material for the water system. Take into account the effect of electro ---chemical reaction. Keep the effect of pressure surge on the cooler as low as possible. Where pressure surges are unavoidable provide an expansion tank to damp pulsations.
Fig. 14 A B
The user must provide the machine with a lockable supply ---disconnecting device. This could be, for example, a disconnect switch with fuses. If a circuit breaker is used it must be suitable for the motor starting characteristics.
Connect the machine to the main power supply in accordance with the electrical diagram in chapter 13.1.4.
Use appropriate bolts to anchor the machine.
Water cooling connection 10 12 17 Shut ---off valve Connection port with stopper Safety relief valve
Cooling water outlet Cooling water inlet
6 --- 32
Installation
The user is to provide the following fittings:
Dirt trap with max. 0.1 mm strainer mesh. Shut ---off valves (10) and connection ports (12) for maintenance and venting. Safety relief valve (17) prevents build ---up of excessive pressure. Blowoff pressure and capacity are related to the users installation design. Keep to the cooler technical specification. Connect the cooling water line to the fitting. Open the shut ---off valve on the cooling water outlet (A). Slowly open the cooling water inlet shut ---off valve (B) to gradually fill the cooler with water. Vent the water lines.
6.5.3 6.5.3.1
Heat recovery system connection Internal heat recovery (option W2, W3) The dimensional drawing in chapter 13.1.3 gives the flow direction, size and position of the connection ports. Use connecting lines of suitable material. Take into account the effect of electro ---chemical reaction. Keep the effect of pressure surge on the heat exchanger as low as possible. Where pressure surges are unavoidable provide an expansion tank as a damper.
Fig. 15 A B Outlet Inlet
The user is to provide the following fittings:
Heat recovery 10 12 17 Shut ---off valve Connection port with stopper Safety relief valve
Dirt trap with max. 0.1 mm strainer mesh. Shut ---off valves (10) and connection ports (12) for maintenance and venting. Safety relief valve (17) on the inlet (B) prevents build ---up of excessive pressure. Blowoff pressure and capacity are related to the users installation design. Keep to the heat exchanger technical specification.
6 --- 33
Installation
Connect the water lines to the fittings. Open the shut ---off valve on the outlet (A). Slowly open the inlet (B) shut ---off tap to gradually fill the heat exchanger with water. Vent the lines.
6.5.3.2
External heat recovery system (option W1) The dimensional drawing in chapter 13.1.3 gives the flow direction, size and position of the connection ports.
Follow the manufacturers instructions on connecting the external heat exchanger.
6 --- 34
Initial Start--- up
7
7.1
Initial Start---up
Safety
Danger of fatal injury from electric shock! DANGER Contact with live electric components can cause serious injury or death.
Isolate all phases of the main power supply. (switch off the main isolator) Ensure that the power supply cannot be switched on again (lock off). Check that no voltage is present.
Compressed air can cause injury or death. WARNING Serious injury or death can result from loosening or opening components under pressure.
Initial start ---up may only be carried out by authorized personnel! Before switching on ensure that:
7.2
Before Every Initial Start---up

Initial start ---up of the machine may only be carried out by trained and authorized installation or maintenance personnel. Incorrect or improper start ---up can cause damage to the machine. Special measures on re --- starting after storage: Storage period longer than... 12 months Action to take
36 months
Close shut ---off valves or otherwise isolate the machine from the comopressed air system to ensure that no compressed air can flow back into the machine. De---pressurize all pressurized components and enclosures. Check all machine hose connectors with a hand ---held pressure gauge to ensure that all read zero.
no one is working on the machine, all panels are in place and secured, all access doors are closed.
Change the oil filter. Change the oil separator cartridge. Change the cooling oil. Have the motor bearings checked by an authorized KAESER distributor. Have the overall technical condition checked by an authorized KAESER distirbutor.
7 --- 35
Initial Start--- up
7.3 Check Installation and Operating Conditions
Cover all points in the check list before starting the machine. Check 1 All installation conditions meet? 2 Users lockable supply disconnecting device installed? 3 Is the power supply as specified on the nameplate? 4 Supply cable section and fuse rating adequate? 5 All electrical connections checked for tightness? 6 Shut ---off valve fitted to compressed air outlet? 7 Connection made to air main with hose or axial compensator? 8 Sufficient cooling oil in the oil separator tank? (cooling oil indicator outside the red zone?) 9 Required quantity of cooling oil poured into the inlet port? 10 Motor protection relay set correctly with regard to the power supply? 11 Operators fully aquainted with safety regulations? 12 Supply of cooling water ensured? (option K2) 13 Machine anchored to the floor? (option H1) 14 All access doors closed and latched and all removable panels in place and secured? Tab. 33 Checklist, installation conditions

Chapter 5 6.4 2 2.9.2 6.3 6.3
Done?
7.6 7.5
6.5.2 6.5.1 4.1.1
7.4
Setting the overload protection cut---out

Compressor motor: In the star ---delta configuration the phase current is fed via the overload protection cut --out. This phase current is 0.58 times the rated machine current (see nameplate in the control cabinet). Setting The standard setting is made at the factory. To prevent the overload protection cutout from being triggered by voltage fluctuations, temperature influences or component tolerances, the setting can be higher than the arithmetical phase current.
7.5
Motor Protection Switch Setting

Fan motor In direct on ---line start the starting current is fed via the motor overload protection switch. Setting The standard setting is made at the factory. To prevent the overload protection switch from being triggered by voltage fluctuations, temperature influences or component tolerances, the setting can be higher than the motor rated current (see motor nameplate). It should be 1.2 x FLA.
7 --- 36
Initial Start--- up
7.6 Pour Cooling Oil into the Inlet Port
Equipment: 2 quart cooling oil
The airend must be manually filled with cooling oil before initial start ---up and after being out of use for more than 3 months. Use the same type of oil.
A sticker giving the type of oil used is found near the oil separator tank filling port.
Fig. 16 1 2

Inlet valve oil filling port
Screw plug Inlet valve Remove the plug (1) from the inlet valve (2). Pour cooling oil into the airend.
Fig. 17 1 2

Coupling 3 4 Cover Rotational direction arrow
Compressor block Coupling Remove the cover (3). Note the rotational direction arrow (4).
7.7
Checking Direction of Rotation

The machine is designed for a clockwise field.
Grasp the coupling (2) and turn it and the airend shaft (1). Replace the coupling cover (3).
Check the supply with a phase sequence indicator. If the compressor motor turns in the wrong direction, change the motor supply phases L1 and L2.
7 --- 37
Initial Start--- up
Alternatively, the direction of rotation can be checked by briefly switching the machine on and off again.
Switch the machine off as soon as the direction of rotation is seen and compare it with the direction arrows on the motor and airend.
7.8
Initial Start---up
Open the shut ---off valve to the compressed air system. Switch on at the main supply isolator.
The controller makes a self---test and the green LED Power ON lights.
The green LED Machine ON lights.
This ensures good distribution of cooling oil.
The machine switches to the LOAD state and delivers compressed air. Watch for any faults occurring in the first hour of operation. After the first 50 operating hours carry out the following:
7.9
Setting System Pressure

The system pressure p1 is factory set to the highest possible value. Adhustment is necessary for individual operating conditions.
Press the Operating state LOAD/IDLE key. Press the ON key.
Allow the machine to idle for at least one minute.
Press the Operating state LOAD/IDLE key.
Check that all electrical connections are tight.
System pressure setting is described in the SIGMA CONTROL service manual. The machine may toggle a maximum of twice per minute between LOAD and IDLE. Reducing starting frequency: Increase the difference between cut ---in and cut ---out pressure. Add an air receiver downstream to increase buffer capacity.
7 --- 38
Operation
8 Operation
Fig. 18 1 2 3 4
Switching On and Off 5 6 7 8 13 Remote key LOAD LED IDLELED Power ON LED (green) LOAD / IDLE toggle key
Machine ON LED (green) ON key (I) OFF key (0) Clock key
8.1
Switching On and Off

Always switch the machine on and off with the ON and OFF keys. The supply disconnecting device is installed by the user.
8.1.1
Switching on Compressed air can cause serious injury! WARNING Serious injury possible.
Never direct compressed air at a person or animal!
Switch on at the main supply isolator. Press the ON key (2).
The controller makes a self---test and the green LED Power ON (8) lights. The green LED Machine ON lights (1). The compressor motor runs, assuming the system pressure is lower than the cut ---out pressure. 8.1.2 Automatic restart Pre --- condition: System pressure is lower than cut ---out pressure. Automatic restart is factory ---set. The machine restarts automatically when power is resumed after a power cut.
Ensure that: no one is working on the machine, all panels are in place, all access doors are closed, no parts of the machine are colder than + 37 F.
8 --- 39
Operation
8.1.3 Switching Off The machine switches to IDLE and the LED (7) blinks. The Machine ON LED goes out (1).

Press the LOAD/IDLE toggle key (13).
After running in idle for 20 seconds, press the OFF key (3). Switch off and lock out the main supply isolator.
8.2
Switching Off in an Emergency and Switching On Again
Fig. 19 9
Switching off in an emergency
EMERGENCY STOP button
Switching off The EMERGENCY STOP remains latched in. The machine pressure system is vented and the machine is prevented from re---starting. Starting again Pre --- condition: Fault rectified.

Press the EMERGENCY STOP button (9)
Turn the EMERGENCY STOP button in the direction of the arrow to unlatch it. Press the Reset key (11). Switch the machine on.
8.3
Remote On and Off Switching

Pre --- condition: Connection to a remote control device.
The LED in the corner of the key lights. The remote control device has control of the machine. The machine can still be switched on and off by the ON and OFF keys (2 and 3) if required.
Press the Remote key (5).
8 --- 40
Operation
Apply the remote warning label to the machine where it is plainly visible. BEWARE! This machine is remotely controlled and can start at any time. Label the remote control device accordingly: Before starting, make sure that no one is working on the machine and it can be safely started.
8.4
Switching on and off with the Clock

Pre --- condition: Clock programmed Press the Clock key (4). The LED in the corner of the key lights. The integrated clock has control of the machine. Apply the time---controlled warning label to the machine where it is plainly visible. BEWARE! This machine is clock --- controlled and can start at any time.
8.5
Acknowledging and Resetting Warning and Alarm Messages
Fig. 20 10 11 12
Acknowledging and Resetting Warning and Alarm Messages Warning LED (yellow) Alarm LED (red) Acknowledge (reset) key
Alarm An alarm shuts the machine down automatically. The red Alarm LED blinks (11). Faults are displayed on the New value principle: Alarm is triggered Alarm is acknowledged Alarm delets or Alarm is triggered Alarm delets Alarm is acknowledged LED blinks LED blinks LED out LED blinks LED illuminates LED out
8 --- 41
Operation
Warning The display shows a maintenance or warning message. The yellow warning LED (10) blinks, for example, if a maintenance task is due. 8.5.1 Resetting alarm messages Pre --- condition: Fault rectified.
Press the Acknowledgement (reset) key (12).
The alarm LED (red) goes out (11). The machine is now ready to start again. 8.5.2 Resetting warning messages Pre --- condition: The cause of the warning eliminated. Maintenance task completed.
Press the Acknowledgement (reset) key (12).
The warning LED (yellow) goes out (10).
8 --- 42
Event Recognition and Fault Rectification

9 Event Recognition and Fault Rectification
Inform KAESER service if the event cannot be rectified by the action suggested. Do not attempt rectifications other than those given in this manual. The measures valid for your machine are dependant on the individual equipment. There are three types of event: Description An event that triggers an alarm (with automatic shut ---down) An event that triggers a warning (no shut --down) Miscellaneous events (faults) Indicated by Blinking red LED Blinking yellow LED No indication see chapter 9.1 9.2 9.3
9.1
Alarms (machine shut---down, red LED blinking)

Message access doors
ADT
Possible cause Door opened during machine operation. Maximum airend discharge temperature exceeded.
Action Close the door(s). Clean cooler. Machine positioned with cooling air outlet too near a wall. Check cooling oil level. Maintain permitted room temperature. Check the cooling oil level. Replace oil filter. Clean cooler. Machine positioned with cooling air outlet too near a wall. Check cooling oil level. Maintain permitted room temperature. Check the cooling oil level. Replace oil filter. Changeover phase lines L1 and L2. Check line and connection.
ADT dT/dt
Maximum airend discharge temperature rise rate exceeded.
airend rotation AI 1 open cct.
The motor is turning in the wrong direction. Connection is broken between the system pressure transducer and analog input 1. Short circuit to earth. Connection is broken between the internal pressure transducer and analog input 2. Short circuit to earth.
AI 2 open cct.
Check line and connection.
9 --- 43

Message AI 3 open cct. Possible cause No connection between the sensor measuring airend discharge temperature and the analog input 3. No connection between the sensor measuring motor temperature and the analog input 4. There is no connection between the sensor allocated to analog input 5 and the input itself. Short circuit to earth. There is no connection between the sensor allocated to an analog input and the input itself. Short circuit to earth. ... AI 8 open cct. AI 1 short cct. The connection between the sensor and the analog input is shorted. Check line and connection. Action Check line and connection.
AI 4 open cct.
AI 5 open cct.
AI 6 open cct.
... AI 8 short cct. back pressure
blowoff prot.
Back pressure in the oil separator tank caused by poor venting. The blowoff pressure of the pressure relief valve on the oil separator tank has been exceeded. Fault in condensate drainage. Cooling water pressure too low. EMERGENCY STOP button pressed.
Check venting line.
condensate drain coolingwater low
EMERGENCYSTOP ext. message 0 ... ext. message 5 Fan M2 I Fan M3 I Fan M4 I
Change the oil separator cartridge. Open the shut ---off valve in the venting line. Check condensate drainage. Check cooling water supply. Check that cooling water shut ---off valve is fully open. Unlatch the pushbutton. Rectify fault.
First fan motor shut down because of overload. Second fan motor shut down because of overload. Third fan motor shut down because of overload.
Investigate cause. Reset overload trip. Investigate cause. Reset overload trip. Investigate cause. Reset overload trip.
9 --- 44

Message HT cell mains cont. off? Possible cause Fault in the high tension cell. The mains contactor does not drop out despite an OFF command. The mains contactor does not pull in despite an ON command. Fault in mains power supply. Machine model indistinct Drive motor shutdown because of overload. Action
mains cont. on?
mains monitor model motor I
Have the mains power supply checked. Change the oil separator cartridge. Check minimum pressure/ check valve.
motor bearings neutral p ---switch neutral T---switch no press. buildup
O 0.6/A 0.7
O 1.6/A 1.7
Power supply
PD temperature
PD temperature
oil p
motor T
Drive motor overheated.
Drive motor bearings overheated.
Machine produces no compressed air. The setpoint pressure does not rise above 50 psig for a preset period. Short circuit in the line between output O 0.6 or O 0.7 and a consumer. Short circuit in the line between output O 1.6 or O 1.7 and a consumer. No changeover to load as long as the minimum oil pressure is not reached. Compressor outlet temperature too low. Compressor outlet temperature too high. 2. Power failure
Investigate cause. Ensure adequate ventilation. Install an extractor. Clean the motor. Grease the motor bearings with the greasing device. Rectify fault Rectify fault Check for air leaks. Check the coupling / V---belts.
Check oil circulation. Check pressure switch, line and connection.
Check the fan motor. Clean the cooler. Check the cooling oil level. Check power supply voltage. Check door interlock.
9 --- 45

Message pRV Possible cause The blowoff pressure of the pressure relief valve on the oil separator tank has been exceeded. Pressure switch on the refrigerant compressor activated. Action Replace the pressure relief valve.
softstart
start T
Ambient temperature below + 40 F. V---belts broken The V---belts parted during machine operation. VFD Frequency converter faulty. Tab. 34 Alarm messages and actions
SIGMA CONTROL T
separator T
separator dp
RD compr. T
RD compr. T
RD compr. p
Ensure adequate ventilation. Clean the refrigerant condenser. Clean the cooler. Clean the refrigerant condenser. Ensure adequate ventilation. Install an extractor. Cleaning the cooler
Refrigerant compressor overheating.
Refrigerant compressor too cold. Oil separator cartridge clogged. Maximum temperature on oil separator tank outlet exceeded. SIGMA controller housing temperature to high.
Replace the oil separator cartridge. Check the cutout line.
Ensure adequate ventilation. Ensure permitted room temperature not exceeded. Check control cabinet ventilator (filter mats).
Fault in the soft start system. Air temperature at the airend discharge port too low.
Heat the compressor room.
Replace the V---belts.
9 --- 46

9.2 Warning Messages (yellow LED blinking)
Message access doors
ADT
Possible cause Doors opened during machine operation. The maximum permissible airend discharge temperature will soon be reached.
Action Close access doors. Ensure adequate ventilation. Clean the cooler. Cooling air outlet too near a wall. Check the cooling oil level. Replace the oil filter. Clean/replace the air filter element. Clean/replace the air filter element. Grease the motor bearings.
blowoff prot.
Buffer battery bus alarm
condensatedrain
elect. equip. h
ext.load signal?
error: RS 485
ext. message 0
Bearing maintenance h
air filter h
air filter dp
The pressure drop across the air filter is rising. Air filter element clogged. The service interval to the next air filter element check has expired. The service interval to the next bearing greasing has expired. Warning The blowoff pressure of the pressure relief valve will soon be reached. Data---retention battery run down. The bus link from the Profibus DP interface is interrupted. Fault in condensate drainage. The service interval for checking electrical equipment and wiring has expired. External load signal indistinct: Increased cut ---out pressure exceeded. The external load control has not switched to idle. Wrong configuration or transmission error. Bit rate and character frame for both subscribers identical.
Change the oil separator cartridge. Open the shut ---off valve in the venting line.
Check link and plug.
Check condensate drain and lines. Reset the service interval counter.
Check settings of the external controller. Take the pressure drops across filters and dryer into account. Check the link/interface connections between the two controllers. Check maximum cable length and screening. Check interface parameters. 1 master and 1 slave configured. Rectify fault.
9 --- 47

Message ... ext. message 5 flash memory
Possible cause
Action
mains voltage
Internal controller memory error. 1. power failure: Machine was re---started automatically. SIGMA CONTROL does not recognize the modem. Drive motor overheating.
modem problem
neutral p ---switch neutral T---switch no press. buildup
oillevel oil T
oil filter dp oil filter h
oil change h
motor starts /d
motorstarts /h
motor bearings h
motor T
Check power supply voltage. Check door interlock. Check the link between the SIGMA controller and the modem. Ensure adequate ventilation. Install an echaust ventilator. Clean the motor.
The service interval to the next motor bearing change has expired. The permissible number of motor starts was exceeded in the last 60 minutes.
The permissible number of motor starts was exceeded in the last 24 hours.
The compressor cannot build ---up pressure.
Extend the idle period. Increase capacity of air receiver. Increase cross---section of piping between compressor and air receiver. Extend the idle period. Increase capacity of air receiver. Increase cross---section of piping between compressor and air receiver. Rectify fault Rectify fault Check for air leaks. Check the value given in the analog data menu with the reading on the oil separator tank pressure gauge. Change the cooling oil. Change the oil filter. Change the oil filter.
The service interval to the next oil change has expired. Oil filter clogged. The service interval to the next oil filter check has expired. Oil level too low. Cooling oil temperature too low.
Top up the cooling oil. Increase room temperature. Check the oil circuit. Check temperature gauge switch, line and connection.
9 --- 48

Message PD temperature Possible cause Warning Compressor outlet temperature is low. Warning Compressor discharge temperature too high. Internal RAM defective. Warning The purest class oil content limit will soon be reached. The purest class oil content limit is exceeded. Action
separator h
set output
System pressure
System pressure (vacuum machines only)
Failure of power supply to the frequency converter. V---belt tension V---belt tension too low. V---belt tens. h The service interval to the next V---belt re---tensioning has expired. Tab. 35 Warning messages and actions
VFD mains
separator dp
Remaining oil content
RAM Remaining oil content
PD temperature
Clean the cooler. Check the cooling oil level.
Oil separator cartridge clogged. The service interval to the next oil separator cartridge check has expired. The set output test function is activated. System pressure has fallen below the set low value. Air consumption too high. System pressure has fallen below the set high value.
Check the scavenge tube in the oil separator tank. Check the dirt trap strainer in the scavenge line. Check the scavenge tube in the oil separator tank. Check the dirt trap strainer in the scavenge line. Change the oil separator cartridge. Change the oil separator cartridge. End the set output mode. Check air demand. Check line and connection. Check systpress. low setting. Check for air leaks. Check syspress. high setting. Check if the machine switches to LOAD. Check power supply. Re---tension the V---belts. Re---tension the V---belts.
9 --- 49

9.3 Miscellaneous faults
Alarm Machine runs but produces no compressed air. Possible cause Inlet valve not opening or only opening partially. Venting valve not closing. Pressure system leaking. Action to take
The air demand is greater than the capacity of the compressor. Hose coupling or maintenance hose still plugged into the quick ---release coupling on the oil separator tank. Oil level in the separator tank too high. Inlet valve defective Air receiver too small. Flow into the compressed air system restricted. Switching differential between cut ---in and cut ---out pressure too is small. Hose coupling or maintenance hose still plugged into the quick ---release coupling on the oil separator tank. Oil cooler leaking Connection leaking. Unsuitable oil used. Oil separator cartridge split. Oil level in the separator tank too high. Oil return line clogged. Tab. 36 Miscellaneous events (faults)
Check pipework and connections for leaks and tighten. Check compressed air system for leaks. Shut down the consumer(s). Remove coupling or maintenance hose.
Cooling oil runs out of the air filter. Compressor switches between load and idle more than twice per minute.
Drain off oil until the correct level is reached.
Increase air line diameters. Check filter elements. Check switching differential.
Oil leaking into the floor pan.
Remove coupling or maintenance hose.
Tighten connections. Replace seals. Use SIGMA FLUID cooling oil. Change oil separator cartridge. Drain off oil until the correct level is reached. Check dirt trap in the oil return line.
Cooling oil consumption too high.
9 --- 50
Maintenance
10
10.1
Maintenance
Safety
Any disregard of these instructions and/or incorrect handling may result in serious injuries. Voltage! DANGER Touching electrically energized components can cause serious injury or death.
Isolate completely from the power supply (all conductors) (switch off at the main isolator) Ensure the supply cannot be switched on again (lock off). Check that no voltage is present.
Volt ---free contacts may be under power from an external source even when the machine is isolated from the main power supply.
Minimum pressure/check valve, safety relief valve and inlet valve are heavilly spring--- loaded. WARNING Fatal injury may occur from incorrect opening of spring ---loaded components.
Uncontrolled pressure release! WARNING Serious injury or death can result from loosening or opening components under pressure.
Leakage CAUTION Leaks result in loss of oil and reduced performance. Damage or complete breakdown can result.
Do not open (dismantle) valves. Contact authorized KAESER distributor, if a fault occurs.
Close shut ---off valves or otherwise isolate the machine from the compressed air system to ensure that no compressed air can flow back into the machine. De---pressurize all pressurized components and enclosures. Check all machine hose connectors with a hand ---held pressure gauge to ensure that all read zero.
Test run on completion of maintenance work. Carry out a visual check of the machine.
10 --- 51
Maintenance
Maintenance work may only be carried out by authorized personnel! Before switching on again ensure that:
no one is working on the machine, all panels are in place and secured, all access doors are closed.
10.2
Maintenance Schedule
Maintenance intervals are recommendations only and should be adjusted to suit the installation and operating conditions. According to the way a machine is equipped, sensors and/or maintenance interval counters monitor the operational state of important functional devices. Necessary maintenance tasks are signalled by the SIGMA controller. Keep a log of all service work.
This enables the frequency of individual maintenance tasks to be compared with KAESERs recommendations. A list is given in chapter 10.16. 10.2.1 Resetting maintenance interval counters Maintenance interval counters indicate the operating hours between maintenance tasks. When a maintenance task is completed, reset the corresponding counter to its original value. See the SIGMA CONTROL service manual. Pre --- condition: Maintenance task completed. Service message reset. Activate password level 4. Select the appropriate entry from the maintenance menu. Select reset and y and confirm with the enter key.
10 --- 52
Maintenance
10.2.2 Regular maintenance work When operating conditions are unfavorable (e.g. dusty atmosphere) or when the equipment is heavily utilized, maintenance tasks must be carried out more frequently (shorter intervals).
Heed controller maintenance messages. Have KAESER service adjust the maintenance interval counters to suit operating conditions.
Maintenance tasks Check cooling oil level. Clean or renew the filter mats. Oil and air cooler maintenance. Heat recovery system maintenance. Air filter maintenance.
Change the oil filter.
Interval Weekly
Every 1000 h
Indicated by SIGMA CONTROL Indicated by SIGMA CONTROL but at least annually. Indicated by SIGMA CONTROL but at least every 3 years. Every 2000 h, but at least annually. Every 3000 h Variable (see chapter 10.2.3) Annually
h = operating hours Tab. 37 Regular maintenance work
10.2.3
Oil change intervals The duty cycle and ambient conditions are important criteria for the number and length of the change intervals.
see chapter 10.12.1 10.3.2 / 10.6 10.3 10.4 10.5

10.14
Change the oil separator cartridge.
10.15
Grease the motor bearings.

Check the coupling. Change the cooling oil.
Check that all electrical connections are tight. Check the safety relief valve. Check the overheating safety shutdown function Check the oil and air coolers for leaks.
10.7
10.8 10.13
10.9 10.10 10.3
10 --- 53
Maintenance
KAESER LUBRICANTS SIGMA LUBRICANT DESCRIPTION MAXIMUM RECOMMENDED CHANGE INTERVAL* First Oil Change M---460 S---460 ISO 46 Semi---Synthetic Lubricant ISO 46 Synthetic Lubricant 2000 Hours 6000 Hours Subsequent Oil Change 3000 Hours 8000 Hours
* Cool to moderate ambient temperatures, low humidity, high duty cycle Tab. 38 Oil change intervals lubricants SPECIALTY KAESER LUBRICANTS (Refer to product information to determine suitability.) SIGMA LUBRICANT DESCRIPTION MAXIMUM RECOMMENDED CHANGE INTERVAL* First Oil Change S---680 FG---460 ISO 68 Synthetic Lubricant ISO 46 Food Grade Synthetic Fluid 6000 Hours 2000 Hours Subsequent Oil Change 8000 Hours 3000 Hours
* Cool to moderate ambient temperatures, low humidity, high duty cycle Tab. 39 10.2.4 Oil change intervals speciality lubricants
Regular service work Only authorized KAESER service agents should carry out service work. When operating conditions are unfavorable (e. g. dusty atmosphere) or when the equipment is heavily utilized, service work must be carried out more frequently. Interval up to 12000 hours Up to 12000 hours, at the latest every 3 years Up to 36000 hours, at the latest every 8 years Service tasks Check valves. Change the fan motor bearings or the motor complete. (non re---greasable bearings) Change the fan motor bearings (re---greasable bearings) Change the compressor drive motor bearings. Change the coupling. Change the hose lines.
h = operating hours Tab. 40 Regular service intervals
10 --- 54
Maintenance
10.3
10.3.1
Cooler Maintenance
Air cooling (option K1) Equipment: brush vacuum cleaner
Pre --- condition: Machine switched off. Main disconnect locked out. Machine cooled down. Check the cooler regularly for contamination. Frequency is mainly dependant on local operating conditions. Contamination causes overheating and machine damage.
Avoid dust disturbance. Wear breathing apparatus if necessary. Do not use sharp objects to clean the cooler. The cooler could be damaged. A severely contaminated cooler should be cleaned by a KAESER service agent.
Fig. 21 1 2
Cleaning the cooler
Cooler Brush Dry brush the cooler (1) and use a vacuum cleaner to suck up the dirt.
10.3.2
Filter mat maintenance (option K3) Equipment: Warm water and household detergent Spare parts (as required)
Pre --- condition: Machine switched off. Main disconnect locked out. Machine cooled down.
10 --- 55
Maintenance
Fig. 22 1 2 3
Cooler filter mats
Filter mat Retaining frame Fixing
Removal
Unlock the fixings (3). Use a screwdriver to turn the fixing 90 anti---clockwise. Remove the frame (2).
Cleaning
Replacing
10.3.3
Water cooling maintenance (option K2) Pre --- condition: Machine switched off. Main isolator locked off Machine cooled down. Check the cooler regularly for leaks and contamination. Frequency of checking is dependant on the characteristics of the cooling water. Contamination causes overheating and machine damage.
Cleaning:
Beat the mat (1) or use a vacuum cleaner to remove loose dirt. If necessary, wash the mat in lukewarm water and household detergent then rinse thoroughly. Replace the mat if cleaning is not possible of has already been carried out five times.
Replace the frame and close the fixings. Press and turn the fixings 90 clockwise until they latch.
Observe the airend discharge temperature to detect any tendency to rise.
An authorized KAESER service agent should clean the cooler when the airend discharge temperature is 50 F above the annual average.
10 --- 56
Maintenance
Leakage Pressure in the cooling oil circuit is generally higher than that in the cooling water system. If a leak occurs, oil will run into the cooling water.
Check the cooler visually for leaks. Have an authorized KAESER service agent check the cooler for internal leaks at least once a year.
10.4
Internal Heat Recovery Maintenance (option W2 / W3)

Pre --- condition: Machine switched off. Main isolator locked off Machine cooled down. Deposits in the heat exchanger in machines with heat recovery systems can adversely affect heat transfer. Check the heat exchanger regularly for leaks and contamination. Frequency of checking is dependant on the characteristics of the heat transfer medium. Contamination
Leakage If a leak occurs, cooling oil can flow into the heat transfer medium as pressure the cooling oil circuit is generally higher.
10.5
Air Filter Maintenance.

Equipment: Compressed air Spare parts (as required)
Pre --- condition: Machine switched off Main isolator locked off Machine cooled down.
Have an authorized KAESER service agent clean the heat exchanger as soon as a pressure drop in the heat transfer medium is detected.
Check the heat exchanger visually for leaks. Have an authorized KAESER service agent check the heat exchanger for internal leaks at least once a year.
10 --- 57
Maintenance
Fig. 23 1 2
Air filter maintenance. 3 4 Cover Nut
Nut Air filter cartridge
Open the air filter housing:

Unscrew the nuts (4) and lift out the cover (3) together with the air filter cartridge (2). Unscrew the nut (1) and remove the air filter cartridge. Do not clean the air filter cartridge with liquids. All sealing surfaces are matched to each other. The use of unsuitable air filter cartridges can permit dirt to ingress into the pressure system and cause damage to the machine.
Clean the air filter cartridge by tapping Renew the air filter cartridge after two years at the latest or after it has been cleaned five times. Tap the cartridge at the end a number of times with the palm of the hand.
Cleaning the air filter cartridge with compressed air: Use dry compressed air (< 70 psig!) to blow dirt from the air filter cartridge at a slant from the inside to the outside.
Close the air filter housing Clean all parts and sealing surfaces. Insert the air filter cartridge in the cover and affix with the nut (1). Affix the cover in the machine with the nuts (4). Close all access doors and replace all cover panels. Switch on the power supply and reset the maintenance interval counter.
10 --- 58
Maintenance
10.6 Filter mat maintenance (control cabinet)
Equipment: Warm water and household detergent Spare parts (as required)
Pre --- condition: Machine switched off. Main isolator locked off Machine cooled down.
Fig. 24 1 2
Control cabinet ventilator
Ventilator grill Filter mat Remove the ventilator grill (1) and the filter mat (2). Beat the mat or use a vacuum cleaner to remove loose dirt. If necessary, wash the mat in lukewarm water and household detergent then rinse thoroughly. Replace the mat if cleaning is not possible or has already been carried out five times. Lay the filter mat in the frame and push on the grill to latch.
Removal Cleaning
Replacing
10.7
Electric motor maintenance

Equipment: Bearing grease Cleaning rags
Pre --- condition: Machine running. Hot components --- danger of burning

CAUTION
Wear long ---sleeve clothing and gloves. Work carefully.
10 --- 59
Maintenance
High ---temperature grease ESSO UNIREX N3 should be used for re---greasing the motor bearings. Bearing damages caused by the use of other brands of grease are excluded from the warranty. Compressor motor The motor bearings are fitted with grease nipples.
Fig. 25 1
Compressor motor maintenance
Grease nipple Clean the grease nipple (1) with a rag. Grease both bearings. Close all access doors; replace and secure all removable panels. Switch on the machine and reset the maintenance interval counter.
Apply the quantity of grease as given on the motor nameplate.

Fan motor Option K1 The motor bearings are fitted with grease nipples.
Fig. 26 1
Fan motor maintenance
Grease nipple Clean the grease nipple (1) with a rag. Grease both bearings. Close all access doors; replace and secure all removable panels.
Apply the quantity of grease as given on the motor nameplate.

Option K2 Fan motor bearings are permanently greased and need no further greasing.
10 --- 60
Maintenance
10.8 Checking the Coupling
Danger of injury from rotating coupling! WARNING Severe injury could result from touching the coupling while it is rotating.
Never switch the machine on without the guard in place over the coupling.
The coupling must be carefully inspected at regular intervals. A defective coupling is recognizable by:
noisy operation, surface cracks, color change.
Fig. 27 1 2
Check for uneven or noisy operation Switch the machine on. Check the coupling (2) for noisy or uneven operation.
Check for damage Pre --- condition: Machine switched off. Main isolator locked off Machine cooled down.
10.9
Checking the Safety Relief Valve.

Pre --- condition: Machine switched off. Activate password level 4. In order to check the safety relief valve, the machines working pressure is raised above the blowoff pressure of the valve.
Checking the Coupling
Safety screen Coupling
Remove the fixing screws from the safety screen (1). Turn the coupling by hand and look for damage or color change. Have a damaged coupling changed by an authorized KAESER service agent. Refit the safety screen. Close all access doors and replace all cover panels.
10 --- 61
Maintenance
Safety relief valve blows off. WARNING Excessive noise is caused when the safety relief valve blows off. There is danger of scalding from hot oil. There is danger of injury from bursting components and compressed air.
Close all access doors; replace and secure all removable panels. Wear ear and eye protection. Abort the test if the working pressure reaches 10% above the blowoff pressure of the valve.
Carry out the test exactly as described in the SIGMA CONTROL manual. Blowoff protection and system pressure monitoring are switched off during the test. The machine may only be operated with a correctly functioning safety relief valve.
Close the users shut ---off valve between the machine and the compressed air system. Read the blowoff pressure on the valve. (the blow ---off pressure is usually to be found at the end of the part identification) Observe the pressure indicator on the SIGMA controller and call up the test function. Stop the test as soon as the safety relief valve blows off or working pressure reaches 10% above the blowoff set point. If necessary, vent the machine and replace the safety relief valve. Deactivate the test function. Open the users shut ---off valve between the machine and the compressed air system.
10.10
Checking the Overheating Safety Shutdown Function

The machine should shut down if the airend discharge temperature reaches 230 F. A detailed description of the checking procedure is to be found in the SIGMA CONTROL service manual.
10.11
Venting the Machine Manually

Pre --- condition: Machine switched off. Main disconnect locked out. Machine cooled down. Compressed air can cause injury or death. WARNING Compressed air and devices under pressure can injure or cause death if the contained energy of the air is released suddenly or uncontrolled. After shutting down the compressor and venting the oil separator tank there is still pressure on the check valve from the air system.
Close the shut ---off valve provided by the user to isolate the machine from the air system. Vent the oil separator tank. Vent the air aftercooler to completely depressurize the system between the users shut ---off valve and the minimum pressure/check valve.
10 --- 62
Maintenance
Escaping oil mist is damaging to health.

CAUTION
Do not direct the maintenance hose at a person while venting. Do not inhale oil mist or vapor. Avoid contact with skin and eyes.
Before undertaking any maintenance or service work on the pressure system the machine must be isolated from the air system and completely vented. The machine is vented in three stages:

the oil circuit vents automatically when the machine is switched off, air is vented manually from the oil separator tank, air is vented manually from the air cooler.
Venting Close the users shut ---off valve between the machine and the air system. If no shut ---off valve is provided, the complete air system must be vented. The hose coupling, shut ---off valve and maintenance hose lie beneath the oil separator tank.
Fig. 28 1 2
Vent the machine. 6 7 Male hose coupling/fitting Shut ---off valve A: closed B: open Maintenance hose
Hose coupling (air cooler venting) Pressure gauge
Hose coupling (oil separator tank venting)
Check that the oil separator tank pressure gauge reads zero. After automatic venting the pressure gauge does not read zero? Make sure that the shut ---off valve is closed. If manual venting does not bring the oil separator tank pressure gauge to zero, call KAESER service.
10 --- 63
Maintenance
Manually venting the oil separator tank
With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (3). Open the shut ---off valve (7) slowly to release pressure. Withdraw the male hose fitting and close the shut ---off valve.
Manually venting the compressed air cooler
10.12
Checking and Topping up the Cooling Oil
10.12.1 Check cooling oil level. Pre --- condition: Machine has been running at least five minutes under load. (minimum 50 Hz for machines under frequency control).
Fig. 29 2 3 4 5
Check cooling oil level. min OK max Minimum oil level Oil level optimum Oil level maximum
Oil separator tank Oil level indicator Indicator markings Green zone Readout oil level.
When the indicator shows minimum level, top up the oil.
With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (1). Open the shut ---off valve (7) slowly to release pressure. Withdraw the male hose fitting and close the shut ---off valve.
Danger of burning from hot surfaces! CAUTION Skin burns are possible. Wear long ---sleeve garments and protective gloves. Work carefully.
10 --- 64
Maintenance
10.12.2 Topping up the cooling oil Equipment: Cooling oil
Pre --- condition: Machine switched off Main disconnect locked out. Machine cooled down.
Danger of explosion from oils and lubricants! WARNING Danger of explosion from oil mist and vapors.
Fire, open flame and smoking are forbidden!
Damage to the machine from unsuitable oil

CAUTION
Never mix different types of oil. Top up only with the same type of oil as already in the machine.
Venting
Close the users shut ---off valve between the machine and the air main. If no shut ---off valve is provided, the complete air system must be vented. The hose coupling, shut ---off valve and maintenance hose lie beneath the oil separator tank.
Fig. 30 1 2 3
Topping up the cooling oil 5 6 7 Oil level indicator Male hose coupling/fitting Shut ---off valve A: closed B: open Maintenance hose
Hose coupling (air cooler venting) Pressure gauge Hose coupling (oil separator tank venting) Oil filling port with plug
10 --- 65
Maintenance
Check that the oil separator tank pressure gauge (2) reads zero. After automatic venting the pressure gauge does not read zero?
Make sure that the shut ---off valve is closed. If manual venting does not bring the oil separator tank pressure gauge to zero, call KAESER service.
Manually venting the oil separator tank
With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (3). Open the shut ---off valve (7) slowly to release pressure. Withdraw the male hose fitting and close the shut ---off valve. With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (1). Open the shut ---off valve (7) slowly to release pressure. Withdraw the male hose fitting and close the shut ---off valve.
Manually venting the compressed air cooler
Topping up the cooling oil
Open the filler plug (4) slowly. Top up the cooling oil. Replace the plug gasket if necessary and re---insert the plug.
Start the machine and carry out a test run
Close all access doors; replace and secure all removable panels. Open the users shut ---off valve between the machine and the compressed air system. Start the machine and allow it to idle for at least one minute. Then switch to LOAD. After about five minutes, check the oil level and top up if necessary. Carry out a visual check for leaks.
10.13
Changing the Cooling Oil

Equipment: Cooling oil Oil catchment container Danger of burns from hot components and oil.
CAUTION
Dispose of the old oil in accordance with local environment protection regulations. Drain the oil thoroughly from:
Oil separator tank Oil cooler Airend The heat recovery system (if installed).
Wear long ---sleeved clothing and gloves. Work carefully.
10 --- 66
Maintenance
Compressed air helps to expel the oil. This pressure can be generated by the machine itself. Alternatively, an external source of compressed air can be used. External air is necessary if:

the machine is not operational, the machine is to be restarted after a long standstill period.
Fig. 31 1 2
Changing the cooling oil, oil separator tank 6 7 Male hose coupling/fitting Shut ---off valve A: closed B: open Maintenance hose Hose coupling (oil drain) Shut ---off valve (venting line) Shut ---off valve (oil drain)
Hose coupling (air cooler venting) Pressure gauge
3 4 5
Hose coupling (oil separator tank venting) Oil filling port with plug Oil level indicator
8 9 10 11
Changing the oil with help from internal pressure Pre --- condition: The machine has been running at least five minutes under LOAD. Machine is switched off. Machine fully vented (no pressure). Pressure gauge on the oil separator tank indicates zero. Close the shut ---off valve (10) in the venting line. Start the machine in idle mode and watch the oil separator tank pressure gauge (2) until it reads 40 ---70 psig. Switch the machine off. Switch off and lock out the supply disconnecting device. Wait at least two minutes for oil to flow back to the separator tank.
Changing the oil with help from an external pressure source Pre --- condition: Machine switched off. Supply disconnecting device switched off and locked out. Machine fully vented (no pressure). Pressure gauge on the oil separator tank indicates zero. External source of compressed air available.
10 --- 67
Maintenance

Close the shut ---off valve (10) in the venting line. With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (3). Connect the maintenance hose to an external air supply. Open the shut ---off valve (7) until the pressure gauge on the oil separator tank reads 40 ---70 psig. Close the shut ---off valve (7) and withdraw the hose fitting from the coupling.
10.13.1 Draining the oil from the separator tank Contact KAESER Service if condensate is detected in the oil. It is necessary to adjust the airend discharge temperature to suit operating conditions. Have an oil container ready. With the shut ---off valve closed, insert the male hose fitting (6 in Fig. 31) into the hose coupling (9, Fig. 31). Place the end of the maintenance hose in the oil container and secure it in place. Open the shut ---off valve (11, Fig. 31). Open the shut off valve (7, Fig. 31) in the maintenance hose slowly and close when air escapes. Close the shut ---off valve (11, Fig. 31) and disconnect the hose.
10.13.2 Draining the oil from the cooler
Fig. 32 1 2 3
Changing the cooling oil, oil cooler 6 7 Male hose coupling/fitting Shut ---off valve
Oil cooler Hose coupling (oil drain) Shut ---off valve
10 --- 68
Maintenance

Have an oil container ready. With the shut ---off valve closed, insert the male hose fitting (6) into the hose coupling (2). Place the end of the maintenance hose in the oil container and secure it in place. Open the shut ---off valve (3). Open the shut ---off valve (7) slowly and allow oil and air to drain completely. Check that the oil separator tank pressure gauge reads zero. Close the shut ---off valve (3) and unplug the hose.
10.13.3 Draining the oil from the airend: Pre --- condition: Machine fully vented (no pressure) Pressure gauge on the oil separator tank indicates zero.
Fig. 33 1 2 3
Changing the cooling oil, airend
Airend discharge Hose coupling (oil drain) Shut ---off valve Have an oil container ready. With the shut ---off valve closed, insert the male hose fitting (6 in Fig. 32) into the hose coupling (2). Place the end of the maintenance hose in the oil container and secure it in place. Open the shut ---off valve (3) and (7. Fig. 32).
Fig. 34 1 2
Turning the coupling
Safety screen Coupling
10 --- 69
Maintenance

Remove the protective screen (1, Fig. 34) and turn the coupling (2, Fig. 34) by hand at least five revolutions until all the oil has run out. Replace and secure the safety screen (1, Fig. 34). Close the shut ---off valve (3) and unplug the hose.
Turning the coupling can cause a small amount of oil to flow back to the cooler and separator tank. Drain oil from the separator tank via the hose coupling (9, Fig. 31). Drain oil from the oil cooler via the hose coupling (2, Fig. 32).
10.13.4 Draining the oil from the heat recovery system (option W1/W2/W3) Pre --- condition: Machine fully vented (no pressure) Pressure gauge on the oil separator tank indicates zero. The procedure is dependent on the heat recovery system installed. Internal heat recovery (option W2 / W3)
Fig. 35 1 2 3
Cooling oil changing, internal heat recovery
Hose coupling Thermostatic valve Shut ---off valve Have an oil container ready. With the shut ---off valve closed, insert the male hose fitting (6 in Fig. 32) into the hose coupling (1) on the thermostatic valve (2). Place the end of the maintenance hose in the oil container and secure it in place. Open the shut ---off valve (3) and (7, Fig. 32) and wait for the cooling oil to drain out. Close the shut ---off valve (3) and unplug the hose. Have an oil container ready. Use the maintenance hose to drain the oil from the drain point of the heat recovery system.
Prepared for heat recovery (option W1)

10.13.5 Filling with cooling oil
Open the oil filler plug (4, Fig. 31) slowly. Fill with oil. Machines with heat recovery systems need correspondingly more oil. Check the plug and gasket for damage and re---insert the plug.
10 --- 70
Maintenance
10.13.6 Start the machine and carry out a test run.
Open the shut ---off valve (10, Fig. 31) in the venting line. Close all access doors; replace and secure all removable panels. Open the users shut ---off valve between the machine and the air main. Switch on the power supply and reset the maintenance interval counter. Allow the machine to idle for at least one minute. Then switch to LOAD. After about ten minutes, check the oil level and top up again, if necessary. Carry out a visual check for leaks.
10.14
Oil filter maintenance

Equipment: Spare parts Have the oil container ready.
Pre --- condition: Machine switched off Main disconnect locked out. Machine fully vented (no pressure). Pressure gauge on the oil separator tank indicates zero. Danger of burning from hot components and oil.
Fig. 36 1 2
Changing the Oil Filter
Oil filter Direction to unscrew Dispose of parts and materials contaminated with oil in accordance with local environment protection regulations.
Unscrew the oil filter counter ---clockwise, catch oil spillage and dispose of correctly. Lightly oil the new oil filter gasket. Screw on the new filter using hand pressure only. Do not use any tool.
The oil filter is turned clockwise to tighten.
CAUTION
Wear long ---sleeve clothing and gloves. Work carefully.
10 --- 71
Maintenance
Start the machine and carry out a test run
Close all access doors; replace and secure all removable panels. Open the users shut ---off valve between the machine and the air main. Switch on the power supply and reset the maintenance interval counter. Allow the machine to idle for at least one minute. Then switch to LOAD. After about five minutes, check the oil level and top up if necessary. Carry out a visual check for leaks.
10.15
Changing the Oil Separator Cartridge

Equipment: Spare parts Cleaning rags
Pre --- condition: Machine switched off. Main disconnect locked out. Machine fully vented (no pressure). Pressure gauge on the oil separator tank indicates zero. Machine cooled down. The life of the oil separator cartridge is influenced by:
Fig. 37 14 15 16 17
contamination in the air drawn into the compressor, adherence to the schedule of oil and air filter changes,
Changing the Oil Separator Cartridge 19 20 21 23 25 Pipe fitting Fitting Gasket Oil separator cartridge Minimum pressure/check valve
Cover Dirt trap Air pipe Retaining bolt
10 --- 72
Maintenance

Unscrew the fitting (20) and carefully put the parts to one side; pull out the copper pipe at item (15). Unscrew the fittings (19) from the ends of the air pipe (16). Withdraw the air pipe from the minimum pressure/check valve (25) and push carefully to one side. Remove the cover retaining bolts (17) and carefully lift the cover (14). The oil separator element cannot be cleaned.
Dispose of parts and materials contaminated with oil in accordance with local environment protection regulations. Take out the used oil separator element (23) together with the gaskets (21) and dispose of according to environmental regulations. Wipe all sealing faces with a cleaning rag. Insert the new oil separator cartridge with gaskets and re---fix the cover. Renew the dirt trap (15) strainer and O ---ring. Connect the air pipe to the minimum pressure/check valve. Replace and tighten all fittings.
Start the machine and carry out a test run Close all access doors; replace and secure all removable panels. Open the users shut ---off valve between the machine and the air main. Switch on the power supply and reset the maintenance interval counter. Allow the machine to idle for at least one minute. Then switch to LOAD. Carry out a visual check for leaks.
10 --- 73
Maintenance
10.16 Logging Maintenance Work
Machine number:
Date Maintenance task carried out Operating hours Signature
Tab. 41
Maintenance log
10 --- 74
Spares, Operating Materiels, Service

11
11.1
Spares, Operating Materials, Service

Note the nameplate
Please quote the data on the nameplate for all inquiries and spare parts orders.
11.2
Ordering Maintenance Parts and Operating Materials

Personal injury or machine damage may result from the use of unsuitable spare parts or operating materials. CAUTION Unsuitable or poor quality maintenance parts and operating materials may damage the machine or impair its proper function. Damage to the machine can also result in personal injury.
Use only genuine spare parts and authorized operating materials. Have an authorized KAESER service agent carry out regular maintenance.
KAESER maintenance parts and operating materials correspond to the original. These are correct for use in our machines. Machine Name Air filter cartridge Filter mat (control cabinet fan) Filter mat (cooler) Oil filter Oil separator cartridge Cooling oil Bearing grease [g] Tab. 42 Machine maintenance parts Quantity 1 2 1 1 1 1 100 400 Number 1250 1100 1050 1200 1450 1600 9.0915.0 6.3234.0
11.3
Maintenance Contract
This ensures the utmost reliability and availability of your compressed air supply system.
Sign a maintenance contract with an authorized KAESER distirbutor.
11.4
Service Addresses
Addresses of KAESER distributors are given at the end of this manual.
11.5
Spare Parts for Service and Repair

Any inspection, maintenance or repair tasks not described in this manual should be carried out by an authorized KAESER distributor. With the help of this parts list you can obtain in advance the spares you need in accordance with your operating conditions.
11 --- 75
De --- commissioning, Storage and Transport

12
12.1
De---commissioning, Storage and Transport

De ---commissioning
De---commissioning is necessary when:
the machine will not be needed for some time, the machine is to be moved to another location, the machine is no longer needed, the machine is to be scrapped.
Temporarily out of service Pre --- condition: The machine can be started at regular intervals. Run the machine once a week under load for at least 30 minutes to ensure corrosion protection.
Out of service for a considerable period Pre --- condition: Before taking out of service the machine should have run under load for at least 30 minutes. Machine switched off and fully vented. Main supply isolator switched off and locked. Allow the machine to cool down completely. In water ---cooled machines, disconnect the water supply and drain all water from the machine. Disconnect all air and electrical connections.
12.2
Packing
Equipment: Desiccant Plastic sheeting Wooden transport crate
Pre --- condition: Machine is de---commissioned. Machine dry and cool. Place desiccant inside the machine cabinet. Wrap the machine in plastic sheeting.
Transport packing A wooden crate is required for ground transportation to protect the machine from mechanical damage. Consult an authorized KAESER service agent for advice on packing for sea or air transport.
12 --- 82

12.3 Storage
Pre --- condition: The machine is adequately packed.
Moisture and frost CAUTION Machine damage possible.
Store the machine in a dry, frost ---free room. Prevent ingress of moisture and condensation.
Advice can be obtained from KAESER on suitable storage and initial start ---up. Moisture can lead to corrosion, particularly on the surfaces of the airend and oil separator tank. Frozen moisture can damage components, diaphragms, valves and gaskets.
12.4
12.4.1
Transporting
Safety Transport only by fork truck or lifting cradle and with personnel trained in the safe use of the transport equipment. The water cooling system of water ---cooled machines must be drained completely if there is danger of frost.
Take weight and centre of gravity into consideration. The centre of gravity is shown in the drawing in chapter 13.1.3. Make sure the danger zone is clear of personnel during transporting.
Fork truck Pre --- condition: The whole machine is over the forks.
Fig. 38
Transport by fork truck
12 --- 83

12.4.2 Transverse beams Pre --- condition: The lifting cradle complies with local safety regulations. No pressure bears on the sides of the machine cabinet.
Incorrect application of the lifting cradle can damage the machine.

CAUTION
Do not attach the lifting cradle to any of the machine components. The machine manufacturer can advise on application of a suitable lifting cradle.
Examples of unsuitable fixing points:
pipe supports flanges attached components such as centrifugal separators, condensate drains or filters rain protection covers
The diagram shows how the machine should be lifted by a cradle.
Fig. 39 1 2
12.5
Disposal
Pre --- condition: Machine is de---commissioned. When disposing of a machine, drain out all liquids and remove dirty filters. Parts contaminated with cooling oil must be disposed of in accordance with local environment protection regulations.
Transport with lifting cradle
Transverse beams Straps
Completely drain the cooling oil from the machine. Remove used ail filter and separator cartridge. Hand the machine over to an authorized disposal expert.
12 --- 84
Annex
13
13.1
13.1.1
Annex
Diagrams and Drawings
Pipeline and instrument flow diagram (P&I diagrams)
13 --- 85
Appendix
13.1.2 Pipeline and instrument flow diagram (option C1)
13 --- 91
Appendix
13.1.3 Dimensional drawing
13.1.3.1 Air cooling (option K1)
13 --- 97
Appendix
13.1.3.2 Water cooling (option K2)
13 --- 100
Appendix
13.1.4 Electrical diagram
13 --- 103

Compresor Kaeser CSD100 PDF

Uploaded by

Copyright:

Available Formats

Compresor Kaeser CSD100 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Compresor Kaeser CSD100 PDF

Uploaded by

Copyright:

Available Formats

What technical specifications are provided for the compressor?

What technical specifications are provided for the compressor?

What safety considerations are outlined in the document?

What safety considerations are outlined in the document?

SERVICE MANUAL

Screw Compressor Model: CSD 100/125

Regarding this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 --- 1

Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 --- 3

Safety and Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 --- 13

Design and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 --- 20

Installation and Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 5 --- 28

Initial Start---up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 --- 35

Event Recognition and Fault Rectification . . . . . . . . . . . . . . . . . . . . . . 9 --- 43

11 Spares, Operating Materials, Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 --- 75

12 De ---commissioning, Storage and Transport . . . . . . . . . . . . . . . . . . . . 12 --- 82

Regarding this Document

Regarding this Document

Symbols and Identifications

Always read and diligently comply with warning notices.

Regarding this Document

This indicates important information.

Weight [lb] Tab. 3

Free Air Delivery (FAD)

under load at rated speed, rated delivery and rated pressure.

Sound pressure level (60Hz) [dB(A)] Tab. 8 Sound Pressure Level

Motor and Performance

CSD 100 0.13 2700 TEFC

CSD 125 0.13 2700 TEFC

Three ---phase star (wye); four wire; earthed neutral

Three ---phase star (wye); three wire; earthed neutral

CSD 100 450 2x 4xAWG4/0 320 310

CSD 125 500 2x 4xMCM250 354 345

Water cooling (option K2)

CSD 100 50 8.8 7

CSD 125 50 10.6 7

Flow rate [gpm] Max. heat capacity available [kW]

Safety and Responsibility

Safety and Responsibility

Installation and maintenance personnel Authorised installation and maintenance personnel:

Safety and Responsibility

as breathing air for processing foodstuffs. Unsuitable compressed air!

Injury and/or contamination can result from breathing compressed air.

Safety and Responsibility

Do not open (dismantle) valves. Contact authorized KAESER distributor.

Further dangers Handling cooling and lubricating fluids

Safety and Responsibility

Safety and Responsibility

Safety and Responsibility

Location of safety signs

foam powder carbon dioxide sand or earth powerful water jet

Unsuitable or unsafe extinguishing media:

Design and Function

Design and Function

Sound damping Protection Cooling air flow control

Design and Function

Design and Function

Design and Function

Filter mat panel

Cooling air filter mat