100% found this document useful (1 vote)
8K views4 pages

Difference Between MSP and SNCP

The document is a request from Ankur for an explanation of the differences between MSP (Multiplex Section Protection) and SNCP (Sub-Network Connection Protection), and guidance on when each would be used. Multiple respondents provide details on the key differences: - MSP protects fibers between two nodes using hardware, while SNCP protects paths through a network using software. - MSP has a 16 node limit and protects STM-1, while SNCP has no node limit and protects lower rates like T1/E1. - MSP can be implemented with line cards and switching matrices, while SNCP uses tributary and connection function cards. - In terms of use cases,

Uploaded by

sajjadrizvi110
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
8K views4 pages

Difference Between MSP and SNCP

The document is a request from Ankur for an explanation of the differences between MSP (Multiplex Section Protection) and SNCP (Sub-Network Connection Protection), and guidance on when each would be used. Multiple respondents provide details on the key differences: - MSP protects fibers between two nodes using hardware, while SNCP protects paths through a network using software. - MSP has a 16 node limit and protects STM-1, while SNCP has no node limit and protects lower rates like T1/E1. - MSP can be implemented with line cards and switching matrices, while SNCP uses tributary and connection function cards. - In terms of use cases,

Uploaded by

sajjadrizvi110
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Dear All, Could anyone please tell me the basic and pratical difference between MSP and SNCP?

Also can someone tell me when can we use MSP and when can we go for SNCP?

I know the practical set-up for both but couldn't figure out when to use which one of these two. With advantages and disadvantages of each.

Hope the reader would be clear with my query and will be able to provide me the details.

Thanks for your inputs in advance.

Regards, Ankur

Huub van Helvoort

Hello Ankur, You asked: > Could anyone please tell me the basic and pratical difference between > MSP and SNCP? MSP = Multiplex section protection, because Multiplex section, Regenerator section and Optical section are in general 1:1:1 MSP is in general protecting the fibers between two nodes. SNCP = sub-network connection protection, this is in general protection of (a section of) a path in a network and applied to VC-n. > Also can someone tell me when can we use MSP and when can we go for > SNCP? Physcal section and path, as described above.

> I know the practical set-up for both but couldn't figure out when to > use which one of these two. With advantages and disadvantages of > each. MSP can only be applied between two adjacent nodes. SNCP can be aplied on a path through a network, passing many nodes. Cheers, Huub. -reply to hhelvooort with 2 'o's ================================================================ http://www.van-helvoort.eu/ ================================================================ Always remember that you are unique...just like everyone else...

Azhar

- show quoted text -

SNCP is faster than MSP (less switching time). MSP has 16 nodes limit where as no limit for SNCP. Minimum protection unit of SNCP is T1 (or E1) where as for MSP is STM-1 (not sure about SONET). SNCP is always 1+1 (to my knowledge but Huub can verify it) where as MSP can be 1+1 or 1:N. MSP is implemented by switching matrix card where as SNCP is implemented by tributary card.

Huub van Helvoort

Hello Azhar, You added: >> Could anyone please tell me the basic and pratical difference between >> MSP and SNCP?

>> Also can someone tell me when can we use MSP and when can we go for >> SNCP? >> >> I know the practical set-up for both but couldn't figure out when to >> use which one of these two. With advantages and disadvantages of >> each. >> >> Hope the reader would be clear with my query and will be able to >> provide me the details. >> >> Thanks for your inputs in advance. >> >> Regards, >> Ankur > > SNCP is faster than MSP (less switching time). The requirement is faster than 50 ms for each, it is up to the implementation how fast it actually is. MSP is normally faster because it covers only one section, SNCP covers more sections and experiences more propagation delay. > MSP has 16 nodes limit where as no limit for SNCP. MSP has 2 nodes (yes the APS protocol has space for 16 but that is irrelevant for MSP), MS-SPRing (the ring protection variant of section protection) supports up to 16 nodes. > Minimum protection unit of SNCP is T1 (or E1) This should be VC-11 or VC-12 for SNCP > where as for MSP is STM-1 (not sure about SONET). STM-0 is covered as well, as are the SONET OC-x rates. > SNCP is always 1+1 (to my knowledge but Huub can verify it) SNCP can be 1+1, 1:1, n:m, (1:1)^n, see ITU-T rec. G.808.1 > where as MSP can be 1+1 or 1:N. OK. > MSP is implemented by switching matrix card MSP can be implemented on the line card and in the HO connection function (VC4 switching matrix). > where as SNCP is implemented by tributary card. SNCP is a function supported by the HO connection function (VC-4) and LO connection function (VC-3, VC12, VC11) see the functional models in ITU-T rec. G,783

Cheers, Huub. -reply to hhelvooort with 2 'o's ================================================================ http://www.van-helvoort.eu/ ================================================================ Always remember that you are unique...just like everyone else...

[email protected]

MSP is harware protection with a standby card while SNCP is a path protection. On Wednesday, 4 July 2007 02:54:20 UTC+5:30, Ank wrote: > Dear All, > > Could anyone please tell me the basic and pratical difference between > MSP and SNCP? > Also can someone tell me when can we use MSP and when can we go for > SNCP? > > > I know the practical set-up for both but couldn't figure out when to
- show quoted text -

You might also like