E2 PTAct 9 7 1 Directions

9.7.
1: Packet Tracer Skills Integration Challenge Activity

Topology Diagram
Introduction:
This Packet Tracer Skills Integration Challenge Activity is similar to the activities you created for Chapter 7, "RIPv2". The scenario is slightly different, to allow you to better practice your skills. In this activity, you build a network from the ground up. Starting with a given address space and network requirements, you must implement a network design that satisfies the specifications. Then implement an effective EIGRP routing configuration, manually summarize routes, fine-tune EIGRP metrics and timers, and configure static and default routing for Internet access.
Objectives:
Design and document an addressing scheme based on requirements. Apply a basic configuration to the devices. Test connectivity between directly connected devices. Configure and verify EIGRP routing. Configure EIGRP summary routes. Fine-tune EIGRP. Configure static and default routing for Internet access. Verify full connectivity between all devices in the topology.
Page 1 of 4
All contents are Copyright 2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
CCNA Exploration Routing Protocols and Concepts: EIGRP
9.7.1: Packet tracer Skills Integration Challenge Activity
Addressing Table
Device Interface Fa0/0 Fa0/1 HQ S0/0/0 S0/0/1 S0/1/0 S0/1/1 Fa0/0 B1 Fa0/1 S0/0/0 S0/0/1 Fa0/0 Fa0/1 B2 S0/0/0 S0/0/1 S0/1/0 Fa0/0 B3 Fa0/1 S0/0/0 S0/0/1 ISP Web Server PC1 PC2 PC3 PC4 PC5 PC6 PC7 PC8 Fa0/0 S0/0/0 NIC NIC NIC NIC NIC NIC NIC NIC NIC 209.165.202.129 209.165.201.1 209.165.202.130 255.255.255.252 255.255.255.252 255.255.255.252 209.165.201.2 255.255.255.252 IP Address Subnet Mask Default Gateway N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 209.165.202.129
Page 2 of 4
Task 1: Design and Document an Addressing Scheme.

Step 1: Design an addressing scheme. Based on the network requirements shown in the topology, design an appropriate addressing scheme. For the LANs, use the address space 10.1.32.0/22. Starting with the largest subnets requirements on B1, assign subnets in order throughout the topology. LAN 1 first, then LAN 2. For the WANs, use the address space 172.20.0.0/27. Assign WAN subnets according to the following specifications: Subnet 0 to the WAN link between HQ and B1 Subnet 1 to the WAN link between HQ and B2 Subnet 2 to the WAN link between HQ and B3 Subnet 3 to the WAN link between B1 and B2 Subnet 4 to the WAN link between B2 and B3
Step 2: Document the addressing scheme. Record the network addresses in dotted-decimal/slash format. Document the IP addresses, subnet masks and default gateway addresses. For LANs, assign the first address to the router interface. Assign the last address to the PC. For WAN links to HQ, assign the first address to the HQ router. For WAN links between branch routers: Assign the first address to B1 for the link between B1 and B2. Assign the first address to B2 for the link between B2 and B3.
Task 2: Apply a Basic Configuration.

Step 1: Configure the routers. Using your documentation, configure the routers with basic configurations, including addressing and hostnames. Use class for the enable secret password and cisco for the line passwords. HQ is the DCE connection to the Branch routers and the ISP is the DCE connection to HQ. Step 2: Configure the PCs. Using your documentation, configure the PCs with an IP address, subnet mask, and default gateway.
Task 3: Test Connectivity.

Before continuing, make sure that each device can ping its directly connected neighbor.
Task 4: Configure and Verify EIGRP Routing.

Step 1: Configure EIGRP. Configure all devices with EIGRP routing in Autonomous System 1. In your configuration, make sure you include the following: Disable automatic summarization. Stop routing updates on interfaces that are not connected to EIGRP neighbors.
Page 3 of 4
Step 2: Verify EIGRP. Use verification commands to check your configuration. All routers should be converged on all the 10.1.32.0/22 and 172.20.0.0/27 subnets.
Task 6: Fine-tune EIGRP.

Step 1: Adjust bandwidth values used to calculate metrics. The links between the branch routers (B1 to B2 and B2 to B3) are for back up purposes only. Configure the bandwidth values to 64 kbps so that EIGRP does not equal-cost load across the T1 links to HQ and the backup links to the neighboring branch router. Step 2: Adjust hello intervals for the slower links. Change the hello intervals for the 64 kbps links to 60 seconds.
Task 7: Configure Static and Default Routing.

Since Packet Tracer does not support redistribution of default routes, all routers except ISP will need a default route configured.
Task 8: Test Connectivity and Examine the Configuration.

Test connectivity and examine the configuration.
Page 4 of 4

E2 PTAct 9 7 1 Directions

Uploaded by

Copyright:

Available Formats

E2 PTAct 9 7 1 Directions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

E2 PTAct 9 7 1 Directions

Uploaded by

Copyright:

Available Formats

9.7.

1: Packet Tracer Skills Integration Challenge Activity

CCNA Exploration Routing Protocols and Concepts: EIGRP

9.7.1: Packet tracer Skills Integration Challenge Activity

CCNA Exploration Routing Protocols and Concepts: EIGRP

9.7.1: Packet tracer Skills Integration Challenge Activity

Task 1: Design and Document an Addressing Scheme.

Task 2: Apply a Basic Configuration.

Task 3: Test Connectivity.

Task 4: Configure and Verify EIGRP Routing.

CCNA Exploration Routing Protocols and Concepts: EIGRP

9.7.1: Packet tracer Skills Integration Challenge Activity

Task 6: Fine-tune EIGRP.

Task 7: Configure Static and Default Routing.

Task 8: Test Connectivity and Examine the Configuration.

You might also like