Scribd
Upload
296 views3 pages

1 FSK Modulation

The document describes an experiment to construct a frequency shift keying (FSK) modulation and demodulation circuit. FSK uses two different carrier frequencies, one for a digital 1 and one for a digital 0. A phase locked loop circuit is used for demodulation to detect the frequency changes in the FSK signal. The procedure connects the FSK modulator and demodulator circuits and observes the output waveforms on an oscilloscope to demonstrate FSK modulation and demodulation.

Uploaded by

Sivaranjani Ravichandran
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
296 views3 pages

1 FSK Modulation

The document describes an experiment to construct a frequency shift keying (FSK) modulation and demodulation circuit. FSK uses two different carrier frequencies, one for a digital 1 and one for a digital 0. A phase locked loop circuit is used for demodulation to detect the frequency changes in the FSK signal. The procedure connects the FSK modulator and demodulator circuits and observes the output waveforms on an oscilloscope to demonstrate FSK modulation and demodulation.

Uploaded by

Sivaranjani Ravichandran
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Exp.No.

2 AIM:

FREQUENCY SHIFT KEYING

To construct the FSK modulation and demodulation circuit and to obtain its waveforms. EQUIPMENTS REQUIRED: 1. IC XR2206. 2. Resistors -5.1k (3) 3. Variable resistors-50k , 200k . 4. Capacitors-0.01F, 10F, 1F, 1nF. 5. Function generator (0-1) MHz. 6. RPS (0-15) V. 7. CRO (0-20) MHZ. THEORY: FSK is one of the three main digital modulation techniques. In frequency shift keying, the carrier frequency is shifted in steps i.e. from one frequency to another corresponding to the digital modulation signal. The higher frequency is used to represent a data '1' & lower frequency a data '0', Since the amplitude change in FSK waveform does not matter, this modulation technique is very reliable even in noisy & fading channels. But there is always a price to be paid to gain that advantage. The price in this case is widening of the required bandwidth. The bandwidth increase depends upon the two carrier frequencies used & the digital data rate. Also, for a given data, the higher the frequencies & the more they differ from each other, the wider the required bandwidth. The bandwidth required is at least doubled than that in the ASK modulation. FSK Demodulator: The demodulation of FSK waveform can be carried out by a phase locked loop. As known, the phase locked loop tries to 'lock' to the input frequency. It achieves this by generating corresponding output voltage to be fed to the voltage controlled oscillator, if any frequency deviation at its input is encountered. Thus the PLL detector follows the frequency changes & generates proportional output voltage. The output voltage from PLL contains the carrier components. Therefore the signal is passed through the low pass filter to remove them. The resulting wave is too rounded to be used for digital data processing. Also, the amplitude level may be very low due to channel attenuation. The signal is 'Squared Up' by feeding it to the voltage comparator.

PROCEDURE: 1. Make the connection according to the circuit diagram. 2. A digital data input and carrier signal are given as input to the FSK modulator and observe the output on the CRO. 3. The output of the FSK modulator is given as input to the FSK demodulator circuit. 4. The demodulator output is observed and the graph is plotted for different waveforms. TABULATION:

SIGNAL

AMPLITUDE(v)

TIME PERIOD(ms)

RESULT: The frequency shift keying modulator and demodulator circuit are constructed and its waveforms are obtained.

FSK Modulator Circuit

Model Graph

You might also like