ACOUSTIC EFFECTS PROCESSOR

BASS EFFECTS PROCESSOR

GUITAR EFFECTS PROCESSOR

UB99A/UB99B/UB99MK2
SERVICE MANUAL

UB99A

UB99B

UB99MK2

ACOUSTIC EFFECTS PROCESSOR

BASS EFFECTS PROCESSOR

GUITAR EFFECTS PROCESSOR

CONTENTS
SPECIFICATIONS..........................................................3
PANEL LAYOUT..............................................4
BLOCK DIAGRAM....................................5
CIRCUIT BOARD LAYOUT..........................6
DISASSEMBLY PROCEDURES....................................6
LSI PIN DESCRIPTIONLSI ........................................8
IC BLOCK DIAGRAMIC ...........................................11
CIRCUIT BOARD..................................................12
INSPECTIONS / FACTORY SET / .....14
BACKUP THE USER PATCH DATA
....................................................25
ERROR MESSAGES.....................................26
PARTS LIST
CIRCUIT DIAGRAM

GA 011755

HAMAMATSU, JAPAN
Copyright (c) Yamaha Corporation. All rights reserved. PDF-K366

05.03

UB99A/UB99B/UB99MK2

IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic
service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and
have therefore not been restated.

WARNING :

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise
all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the
appointed service representative.

IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certification,
recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service
departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in
specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the
distributors Service Division.

WARNING :

Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.)

IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable)
components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to
cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT
SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to
solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.

WARNING
Components having special characteristics are marked
those originally installed.

and must be replaced with parts having specification equal to

UB99A/UB99B/UB99MK2

SPECIFICATIONS
Digital Section
Digital signal processing effector
Includes special editor application Sound Editor for
MAGICSTOMP
Patch Select: 2 Modes
Built-in Chromatic Auto Tuner

Sound Editor for MAGICSTOMP

Communications
Receive: Parameter Change, Bulk In (1 patch), Bulk
In (99 patch)
Transmit: Bulk Out (99 patch)

Controller/Switch
Knob x4
CONTROL1, 2, 3, VOLUME

/
4
CONTROL1, 2, 3, VOLUME

Parameter Change, Bulk In (1 patch), Bulk In (99

patch)
Bulk Out (99 patch)

Push Switch x4
UB99A: , +, AUTO F.R./ON/OFF, STORE/EXIT
UB99B/UB99MK2: , +, ON/OFF, STORE/EXIT

4
UB99A: -, +, AUTO F.R./ON/OFF, STORE/EXIT
UB99B/UB99MK2: -, +, ON/OFF, STORE/EXIT

Slide Switch x1
INPUT LEVEL (HIGH/LOW)

1
INPUT LEVEL (HIGH/LOW)

Display
16 x 2 character LCD (w/Back light)
LED x 3 (UB99A: , +, AUTO F.R./ON/OFF)
(UB99B/UB99MK2: , +, ON/OFF)

16 2 character LCD ( )
LED x 3 (UB99A: -, +, AUTO F.R./ON/OFF)
(UB99B/UB99MK2: -, +, ON/OFF)

Connections
INPUT: Standard Monaural Phone Jack
OUTPUT L/MONO, R: Standard Monaural Phone Jack
PHONES: Mini Stereo Phone Jack
USB
AC IN

INPUT )
OUTPUT L/MONO, R
PHONES
USB
AC IN

A/D Converter
24 bit + 3 bit Floating

A/D
24 3

D/A Converter

24 bit

D/A

24

Sampling Frequency

44.1 kHz

44.1 kHz

Memory Allocations

Preset:99
User: 99

99
99

Input Level/Impedance
INPUT HIGH: 25dBm/1 M
INPUT LOW : 15dBm/1 M

/
INPUT HIGH -25dBm/1 M
INPUT LOW -15dBm/1 M

Output Level/Impedance
OUTPUT L/MONO, R: 0dBm/1 k
PHONES L, R: 10 dBm/150

/
OUTPUT L/MONO, R 0dBm/1 k
PHONES L, R: -10 dBm/150

Power
Exclusive Power Adaptor (AC-10)
AC Output: AC 12 V, 1 A

(AC-10)
AC12V, 1000mA

Power Consumption

12 W

12 W

Dimensions (W x H x D)

164 x 62 x 176 mm
(6-7/16 x 2-7/16 x 6-15/16)

(W x H x D)

164 62 176 mm

Weight

910 g (2lbs.)

910 g

Accessories

Power Adaptor (AC-10)

CD-ROM
USB Cable
Owners Manual
Patch List
Effect List

(AC-10)
CD-ROM
USB

UB99A/UB99B/UB99MK2

PANEL LAYOUT
Top Panel
UB99A

UB99B/UB99MK2

1
3

3
2

AUTO F.R.
ON/OFF

1
2
3
4
5

Display
CONTROL Knobs
VOLUME Knob
STORE/EXIT Button /
[UB99A] Switch, + Switch, AUTO F.R./ON/OFF SwitchAUTO F.R./ON/OFF
[UB99B/UB99MK2] Switch, + Switch, ON/OFF SwitchON/OFF

Rear Panel

PHONES

6
6
7
8
9
0
q

INPUT Jack
INPUT LEVEL HIGH/LOW Switch
OUTPUT L/MONO, R Jacks
PHONES Jack
USB JackUSB
AC IN Jack (Power Adaptor)

[Gain= +8dB]

DIC-00014
DIC-00022
DIC-00017

IC101 (8P)

JK101

28

- 7

2
27

IC105 (8P)
LPF

+5A +3.3D

IC102 (8P)

7
4

+3.3D [Gain= -10dB]

IC103 (8P)

IC104
(28P) 26
25

VR101

TR101

2
5

TR102

IC106 (8P) TR103

,107
3
1
5

JK102

IC106
(8P) TR104
,108

19
13,14

SYSTEM
RESET

IC3 (5P)

BLOCK DIAGRAM

UB99A:
UB99B:
UB99MK2:

SW101

JK103

IC1 (48P)

X1

+3.3D

+3.3D

+3.3D

IC2 (28P)

12

X2

55,65

IC5
(176P)

IC10 (44P)

15

JK105

+3.3D

X3

+3.3D

+3.3D
12,13

63

AN0 AN1 AN2

80
78 79

PHONES

+3.3D

IC6 (44P)
66,67

IC114 (8P)

P6-0
58

P6-2
60

P6-1
59

17

(AUTO F.R.)
+
ON/OFF
15
16

STORE/EXIT
13

IC7 (64P)

IC4 (100P)

JK1

+5D
CN1 (16P)
VR1 VR2 VR3
AN0

AN1

AN2

*1 LD1

*2

LD1

from P6_0

SW2
SW1
SW3

from P6_2

from P6_1

TR1

*1

TR2

LD3

D106,107
*2

SW2
SW3
SW1

SW4

AC IN
D109,111
JK104

TR3
IC108
+5V

*1 indicates the name for the UB99A model.

*1 UB99A
*2 indicates the name for the UB99B/UB99MK2 models.
*2 UB99B/UB99MK2

IC109
+5V

DM

IC111
+3.3V

D108

UB99A/UB99B/UB99MK2

TR2

A
IC112
+15V

AC-10

D110,112

IC113
-15V

from P6_2

STORE/
EXIT

TR1

ZD104

ZD103

TR3

LD2
from P6_1

TR105,106
SW4
STORE/
EXIT

from P6_0

LD3

LD2

UB99A/UB99B/UB99MK2

CIRCUIT BOARD LAYOUT

Bottom view

DM

DISASSEMBLY PROCEDURES
1.

Bottom Case

1.

(Time required: about 1 minute)

1-1. [40] 4 [30] 2

( 1)

1-1. Remove the four (4) screws marked [40] and the two
(2) screws marked [30]. The bottom case can then be
removed. (Fig.1)

( : 1 )

Bottom view
[30]

[40]

[40]

Bottom case
[30]: Bind Head Tapping Screw-B+ B 3.0X8 MFZN2BL (EP600190)
[40]: Bind Head Tapping Screw-P+ P 4.0X8 MFZN2BL (VB931600)

Fig.1 1

UB99A/UB99B/UB99MK2
2.

Rear Panel (Time required: about 3 minutes)

2.

( : 3 )

2-1. Remove the bottom case. (See Procedure 1.) (Fig. 2)

2-2. Remove the screw marked [110], the three (3)
hexagonal nuts marked [120] and the three (3) flat
washers marked [130] from the rear panel. AC cord
column and the rear panel can then be removed. (Fig. 2)

2-1. (1 )
2-2. [110] 1 [120]
3 [130] 3 AC
( 2)

3.

3.

DM Circuit Board
(Time required: about 3 minutes)

DM
( : 3 )

3-1.
3-2.
3-3.
3-4.

Remove the bottom case. (See Procedure 1.)

Remove the rear panel. (See Procedure 2.)
Remove the four (4) knobs from the front panel.
Remove the eight (8) screws marked [90]. The DM
circuit board can then be removed. (Fig. 2)

3-1. (1 )
3-2. (2 )
3-3. 4 ( 2)
3-4. [90] 8 DM ( 2)

4.

Foot Switch (Time required: about 3 minutes)

4.

4-1.
4-2.
4-3.
4-4.

Remove the bottom case. (See Procedure 1.)

Remove the rear panel. (See Procedure 2.)
Remove the DM circuit board. (See Procedure 3.)
Remove the hexagonal nut of the foot switch. The foot
switch can then be removed. (Fig.2, Photo. 1)
* Be sure to fit the projection of the foot switch panel to
the groove of the foot swtich when attaching the foot
switches.

4-1. (1 )
4-2. (2 )
4-3. DM (3 )
4-4.
( 2 1)

( : 3 )

Rear view
Spring washer

Foot switch

[120]
[130]

Hexagonal nut

Flat washer

[110] AC cord column

AC

Rear panel

Photo. 1 1

Top view

Bottom view
Knob

[90]

[90]

DM

Foot switch
Hexagonal nut
[90]: Bind Head Tapping Screw-P+ P 3.0X8 MFZN2BL (EP630220)
[110]: Bind Head Screw+ 3.0X8 MFZN2BL (VA295800)
[120]: Hexagonal Nut 9.0 12X2 MFNI33 (LX200060)
[130]: Flat Washer 9.0X14X0.5 MFNI33 (VL802300)

Fig.2 2

UB99A/UB99B/UB99MK2

LSI PIN DESCRIPTIONLSI

HD6413008VF25 (X4196A00) CPU (MAIN)
PIN
NO.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

NAME

I/O

Vcc

_____

FUNCTION

PIN
NO.

NAME

I/O

Analog power supply +3.3V

51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

P26/A14

I/O

P27/A15

I/O

P50/A16

I/O

P51/A17

I/O

P52/A18

I/O

P53/A19

I/O

Vss

CS7/TMO0/TP8/PB0 I/O
_____

CS6/TMIO1/TP9/PB1 I/O

_____

Chip select / / / Port B

CS5/TMO2/TP10/PB2 I/O

_____

CS4/TMIO3/TP11/PB3 I/O
TP12/PB4 I/O
TP13/PB5

I/O

Pulse output / Port B

TP14/PB6 I/O
TP15/PB7 I/O
__________

RESO

Reset

Vss

Ground

TXD0/P90 I/O
TXD1/P91 I/O

Data transmission / Port 9

RXD0/P92 I/O
RXD1/P93 I/O

Data reception / Port 9

______

IRQ4/SCK0/P94 I/O
______

IRQ5/SCK1/P95 I/O
D0/P40

I/O

D1/P41

I/O

D2/P42

I/O

D3/P43

I/O

Vss

D4/P44

I/O

D5/P45

I/O

D6/P46

I/O

P47/D7

I/O

P30/D8

I/O

P31/D9

I/O

P32/D10

I/O

P33/D11

I/O

P34/D12

I/O

P35/D13

I/O

P36/D14

I/O

P37/D15

I/O

Vcc

P10/A0

I/O

P11/A1

I/O

P12/A2

I/O

P13/A3

I/O

P14/A4

I/O

P15/A5

I/O

P16/A6

I/O

P17/A7

I/O

Vss

P20/A8

I/O

P21/A9

I/O

P22/A10

I/O

P23/A11

I/O

P24/A12

I/O

P25/A13

I/O

DM: IC4

Interrupt request / Serial clock / Port 9

Data bus / Port 4

Ground
Data bus / Port 4

Port 4 / Data bus

Port 3 / Data bus

Analog power supply +3.3V

Port 1 / Address bus

Ground

Port 2 / Address bus

_________

FUNCTION
Port 2 / Address bus

Port 5 / Address bus

Ground

P60/WAIT I/O
__________

P61/BREQ I/O

Port 6

__________

P62/BACK I/O
P67/

I/O

STBY

Stand-by mode signal

RES

Reset

NMI

Non-maskable interrupt

Vss

Ground

EXTAL

Clock

XTAL

Clock

Vcc

Power supply +3.3V

P63/AS

P64/RD

P65/HWR

P66/LWR

MD0

MD1

_________
_______

_____
_____

_________
________

Port 6 / System clock output

Port 6

Model control

MD2

AVcc

Power supply +3.3V for A/D

VREF

Reference voltage for A/D

AN0/P70

AN1/P71

AN2/P72

AN3/P73

AN4/P74

AN5/P75

Analog input / Port 7

DA0/AN6/P76 I/O
DA1/AN7/P77 I/O

D/A output / Analog input / Port 7

AVss

Ground for A/D

IRQ0/P80
_____ ______

Interrupt request / Port 8

______

CS
3/IRQ1/P81 I/O
_____ ______
CS
2/IRQ2/P82 I/O
____________ _____ ______
ADTRG
/CS1/IRQ3/P83 I/O
_____
CS0/P84

I/O

Vss

Chip select / Interrupt request / Port 8

A/D trigger / Chip select / Interrupt request / Port 8
Chip select / Port 8
Ground

TCLKA/TP0/PA0 I/O
TCLKB/TP1/PA1 I/O

Timer clock / Pulse output / Port A

TCLKC/TIOCA0/TP2/PA2 I/O

Timer clock / Output comparison / Pulse output / Port A

TCLKD/TIOCB0/TP3/PA3 I/O

Timer clock / Input capture / Pulse output / Port A

A23/TIOCA1/TP4/PA4 I/O

Address bus / Output comparison / Pulse output / Port A

A22/TIOCB1/TP5/PA5 I/O

Address bus / Input capture / Pulse output / Port A

A21/TIOCA2/TP6/PA6 I/O

Address bus / Output comparison / Pulse output / Port A

A20/TIOCB2/TP7/PA7 I/O

Address bus / Input capture / Pulse output / Port A

UB99A/UB99B/UB99MK2

M38K07M4L-303HP (X3921200) CPU (USB)

PIN
NO.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

NAME

I/O

FUNCTION

P12/DQ2/AN2 I/O
P13/DQ3/AN3 I/O
P14/DQ4/AN4 I/O
P15/DQ5/AN5 I/O

Port P1 (In/output)

P16/DQ6/AN6 I/O
P17/DQ7/AN7 I/O
CNVSS
____________

Ground

RESET

System reset input

EccE

Analog power supply +3.3V

VREF

Reference voltage input

Vss

Ground

XIN

Clock input

XOUT

Clock output

Vcc

Power supply +3.3V

CNVSS2

Ground

P60(LED0) I/O
P61(LED1) I/O

Port P6 (In/output)

P62(LED2) I/O
P63(LED3) I/O
PVss

PVcc

Analog power supply +3.3V

DVcc

USBVREF

USB reference power supply

TrON

USB reference volyage output

D0+

I/O

D0-

I/O

P20

I/O

P21

I/O

P22

I/O

P23

I/O

P24

I/O

P25

I/O

USB upstream in/output

Port P2 (In/output)

DM: IC7

PIN
NO.

NAME

I/O

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

P26

I/O

P27

I/O

P50/INT0

I/O

FUNCTION
Port P2 (In/output)
Port P5 (In/output)/Interruption input

P51/CNTR0 I/O

Port P5 (In/output)/Timer X function

P52/INT1

I/O

Port P5 (In/output)/Interruption input

P53

I/O

P54

I/O

P55

I/O

P56

I/O

P57

I/O

P00

I/O

P01

I/O

P02

I/O

P03

I/O

P04

I/O

P05

I/O

P06

I/O

P07

I/O

Port P5 (In/output)

Port P0 (In/output)

P40/EXDREQ/RXD I/O
P41/EXDACK/T
XD I/O
_______

Port P4 (In/output)/External bus interface/Serial I/O

P42/EXTC/SCLK I/O
P43/EXA1/SRDY I/O
P30

I/O

P31

I/O

P32

I/O

Port P3 (In/output)

P33/EXINT I/O
P34/EXCS

I/O

P35/EXWR I/O
P36/EXRD

Port P3 (In/output)/External bus interface

I/O

P37/EXA0 I/O
P10/DQ0/AN0 I/O
P11/DQ1/AN1 I/O

Port P1 (In/output)

AK4528VF (XY624A00) ADC/DAC (CMOS A/D & D/A Converter)

PIN
NO.

NAME

I/O

1
2
3
4
5
6
7
8
9
10
11
12
13
14

VCOM

Common voltage output , VA/2

AINR+

Rch analog positive input

FUNCTION

AINR-

Rch analog negative input

AINL+

Lch analog positive input

AINL-

Lch analog negative input

VREF

Reference voltage

AGND

Analog ground +3.3V

VA

Analog power supply

P/S

Paralle/serial mode select

MCLK

Master clock input

LRCK

Input/output channel clock

BICK

Audio serial data clock

SDTO

Audio serial data output

SDTI

Audio serial data input

PIN
NO.

NAME

CKS0
15
CKS1
16
DIF
17
DFS
18
PDN
19
DEM0
20
DEM1
21
VT
22
VD
23
24 DGND
25 AOUTL26 AOUTL+
27 AOUTR28 AOUTR+

I/O

DM: IC104
FUNCTION

I
I
I

Master clock select

Digital audio interface select

Double speed sampling mode

Power-down mode

I
I
-

De-emphasis frequency select

Output buffer power supply

Digital power supply

Digital ground

Lch analog negative output

Lch analog positive output

Rch analog negative output

Rch analog positive output

UB99A/UB99B/UB99MK2

YSS910-V (XV988B00) DSP6 (Digital Signal Processor)

10

PIN
NO.

NAME

I/O

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88

Vdd
Vss
XI
XO
Vdd5
/SYNCI
/SYNCO
Vdd5
CKI
CKO
CKSEL
Vss
MCKS
/SSYNC
/IC
/TEST
BTYP
/IRQ
TRIG
Vdd5
Vss
/CS
/WR
/RD
CA7
CA6
CA5
CA4
CA3
CA2
CA1
Vss
Vdd
CD15
CD14
CD13
CD12
CD11
CD10
CD09
CD08
CD07
CD06
Vss
Vdd
Vdd5
CD05
CD04
CD03
CD02
CD01
CD00
/WAIT
Vss
SI0
SI1
SI2
SI3
SI4
SI5
SI6
SI7
Vss
Vdd5
SO0
SO1
SO2
SO3
SO4
SO5
SO6
SO7
Vss
DB00
DB01
DB02
DB03
DB04
DB05
DB06
DB07
DB08
DB09
DB10
DB11
DB12
Vdd5
Vdd

I
O
I
O
I
O
I
I
I
I
I
I
O
I/O
I
I
I
I
I
I
I
I
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I
I
I
I
I
I
I
I
O
O
O
O
O
O
O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-

FUNCTION
Power supply (3.3 V)
Ground
System master clock input (60 MHz or 30 MHz)
System master clock output (High or 30 MHz)
Power supply (5 V)
System sync. signal input
System sync. signal output
Power supply (5 V)
System clock input (30 MHz)
System clock output (30 MHz)
System master clock select (0: 60 MHz, 1: 30 MHz)
Ground
Serial I/O master clock input (128 x Fs)
Serial I/O Sync. signal output
Initial clear (RESET)
Test mode setting (0: Test, 1: Normal)
Data bus type select (0: 8 bit, 1: 16 bit)
IRQ output
Trigger signal input/output
Power supply (5 V)
Ground
Chip select signal input
Write signal input
Read signal input

Address bus of internal register

Ground
Power supply (3.3 V)

Data bus of internal register

Ground
Power supply (3.3 V)
Power supply (5 V)
Data bus of internal register

WAIT output
Ground

Serial data input

Ground
Power supply (5 V)

Serial data output

Ground

Parallel data bus

Power supply (5 V)
Power supply (3.3 V)

PIN
NO.

NAME

89
Vss
90
DB13
91
DB14
92
DB15
93
DB16
94
DB17
95
DB18
96
DB19
97
DB20
98
DB21
99
DB22
100
Vss
101
Vdd
102
DB23
103
DB24
104
DB25
105
DB26
106
DB27
107
DB28
108
DB29
109
DB30
110
DB31
111 TIMO/DBOB
112
Vss
113
Vdd5
114
DA00
115
DA01
116
DA02
117
DA03
118
DA04
119
DA05
120
DA06
121
DA07
122
Vss
123
DA08
124
DA09
125
DA10
126
DA11
127
DA12
128
DA13
129
DA14
130
DA15
131
Vss
132
Vdd
133
(n.c)
134
Vdd5
135
DA16
136
DA17
137
DA18
138
DA19
139
DA20
140
DA21
141
DA22
142
DA23
143
Vss
144
DA24
145
DA25
146
DA26
147
DA27
148
DA28
149
DA29
150
DA30
151
DA31
152
Vdd5
153
Vss
154
A00
155
A01
156
A02
157
A03
158
A04
159
A05
160
A06
161
A07
162
A08
163
A09
164
Vss
165
Vdd
166
A10
167
A11
168
A12
169
A13
170
A14
171 A15/RAS
172 A16/CAS
173 A17/CE
174
/WE
175
/OE
176
Vdd5

DM: IC5
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
-

FUNCTION
Ground

Parallel data bus

Ground
Power supply (3.3 V)

Parallel data bus

Timing signal output/ Parallel data bus output control input

Ground
Power supply (5 V)

Memory data bus

Ground

Memory data bus

Ground
Power supply (3.3 V)
Not used
Power supply (5 V)

Memory data bus

Ground

Memory data bus

Power supply (5 V)
Ground

Memory address (SRAM, PSRAM, DRAM)

Ground
Power supply (3.3 V)
Memory address (SRAM, PSRAM, DRAM)
Memory address (SRAM, PSRAM)
Memory address (SRAM, PSRAM), /RAS (DRAM)
Memory address (SRAM, PSRAM), /CAS (DRAM)
Memory address (SRAM), /CE (PSRAM)
Memory write enable signal
Memory output enable signal
Power supply (5 V)

UB99A/UB99B/UB99MK2

IC BLOCK DIAGRAMIC
SN74LVU04APWR(X3936A00)

SN74LV245APWR(X3693A00)

Hex Inverter
DM: IC107

1A

1Y

2A

2Y
3A
3Y
Vss

Octal 3-State Bus Transceiver

DM: IC8,9

14
13
12

11

10

DIR

Vcc

A1

20

19

6A
18

Vcc
OE

A2

A3

17

A4

16

A5

15

B4

A6

14

B5

A7

13

B6

A8

12

B7

10

11

B8

B1

6Y
5A

B2
B3

5Y
4A
4Y

GND

SN74LV4040APWR(X3935A00)
12-Bit Asynchronous Binary Counter
DM: IC110

QL

16 VCC

QF

15 QK

QE

14 QJ

QG

13 QH

QD

12 QI

QC

11 CLR

QB

10 CLK

GND

CLR

11

R
CLK

10

R
T

NJM072M(XC458A00)
TL072CPSR(XV423A00)
Dual Operational Amplifier
DM: IC101

Output A

1
2

Non-Inverting
Input A

-DC Voltage
Supply

+DC Voltage
Supply

Output B

Inverting
Input B

Non-Inverting
Input B

- +
+ -

-V

R
T

R
T

R
T

QA

QB

QC

QD

QE

QA
R

Inverting
Input A

R
T

R
T

R
T

QF

QG

R
T

13
QH

12
QI

NJM5532M(X4980A00)
Dual Operational Amplifier
DM: IC102,103,105,106

V+

B OUT

A+IN

A OUT
A IN

R
T

R
T

14
QJ

15

QK

QL

NJM4556AM(X5049A00)
Dual Operational Amplifier
DM: IC114

A OUT
A IN

V+

B OUT

B IN

A+IN

B+IN

B IN
B+IN

11

UB99A/UB99B/UB99MK2

CIRCUIT BOARD
DM Circuit Board
INPUT INPUT LEVEL
HIGH/LOW

OUTPUT
L/MONO
PHONES

USB

AC IN

Component side

Note: See parts list for details of circuit board component parts.

12

DM:4LP-X5898A0

UB99A/UB99B/UB99MK2

DM Circuit Board

LCD

VOLUME

CONTROL
STORE/
EXIT

ON/OFF (UB99B/UB99MK2)
AUTO F.R. ON/OFF (UB99A)
Pattern side

DM:4LP-X5898A0

13

UB99A/UB99B/UB99MK2

INSPECTIONS / FACTORY SET

1.

Preparation

1-1. Measuring instrument:

Oscillator, Distortion meter, Level meter
1-2. Jig:
USB cable, P.C (Personal computer)
1-3. Connections of terminals:

3-2-2. Check that the input and output values shown below
are satisfied.
INPUT LEVEL
SW setting
Item
Input
1:
sensitivity
2:

INPUT
OUT L/
MONO
OUT R

Monaural Input 1/4 inch Plug (Signal Input)

Monaural Output 1/4 inch Plug (RL 47 K)

3:

Monaural Output 1/4 inch Plug (RL 47 k)

4:

PHONES Stereo Output 1/7 inch Plug (RL 33 )

2.

AC IN

AC ADAPTOR (AC-10)

USB
INPUT
LEVEL

USB Cable

P.C.

HIGH (+10 dB) / LOW (0 dB)

5:
6:
LOW
7:

Measurement Conditions

8:

Unless otherwise specified, input signals are of

sinusoidal waves and the frequency is 1 kHz.
Before turning on power, set knobs of Control VR1,
Control VR2 and Control VR3 at positions near their
respective center.
Set VOLUME VR to maximum and INPUT LEVEL
SW to LOW.
Make sure that the input impedance of the
measuring instrument is 1 M or greater.
Install USB-MIDI driver on the P.C. Get the driver
from the Yamaha web site.

3.

9:
10:
11:
12:
13:
14:

Method of Inspection

3-1. How to get TEST MODE

3-1-1. When turning on power while pushing [] SW and
[+] SW, you will get TEST MODE. (This unit has no
power switch. Power is turned on by connecting the
AC adaptor.)

HIGH

Input terminal,
Conditions
INPUT
-4.5 dBm (1 KHz)
INPUT
ditto
-4.5 dBm (10 KHz)
INPUT
ditto
-4.5 dBm (100 KHz)
INPUT
ditto
-22.5 dBm (100 Hz)
INPUT
ditto
-22.5 dBm (10 KHz)
INPUT
ditto
-22.5 dBm (1 KHz)
INPUT
ditto
-13.5 dBm (1 KHz)
INPUT
ditto
-13.5 dBm (10 KHz)
INPUT
ditto
-12.5 dBm (100 Hz)
INPUT
ditto
+5.5 dBm (100 Hz)
INPUT
ditto
+4.5 dBm (10 kHz)
INPUT
ditto
+4.5 dBm (1 kHz)
INPUT
ditto
-15 dBm (1 KHz)
INPUT
Noise level Pull Out Plug

15: ditto

INPUT

16: ditto

INPUT

17: ditto

INPUT

18:

Distortion
factor

19: ditto
20: ditto

[email protected]@V1.0@
PUSH@[ON/OFF]@SW
3-1-2. Proceed with inspection according to the instruction
in the display.
Make sure that the back light LED of LCD is lit.
3-2. DSP & DRAM & AD/DA Check
3-2-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@DSP&DRAM@
PUSH@[ON/OFF]@SW
Make sure that a signal wave is outputted.

14

21: ditto

INPUT
-12 dBm (1 KHz)
Push Insert Plug
INPUT
+6 dBm (1 KHz)
INPUT
+8 dBm (1 KHz)
INPUT
-10 dBm (1 KHz)

Output terminal,
Specifications
OUT L/MONO
0 dBm 3 dB
OUT L/MONO
0 dBm 3 dB
OUT L/MONO
0 dBm 3 dB
OUT R
0 dBm 3 dB
OUT R
0 dBm 3 dB
OUT R
0 dBm 3 dB
PHONES R
0 dBm 3 dB
PHONES R
0 dBm 3 dB
PHONES R
0 dBm 3 dB
PHONES L
0 dBm 3 dB
PHONES L
0 dBm 3 dB
PHONES L
0 dBm 3 dB
OUT L/MONO
0 dBm 3 dB
OUT L/MONO
-44 dBm or less
OUT R
-44 dBm or less
PHONES L
-52 dBm or less
PHONES R
-52 dBm or less
OUT R
0.5% or less
OUT L/MONO
0.5% or less
PHONES L
0.5% or less
PHONES R
0.5% or less

0 dBm=0.775 V

After checking, set the INPUT LEVEL SW to LOW.

UB99A/UB99B/UB99MK2
3-3. SRAM Check
3-3-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@SRAM@CHECK@
NOW@WRITE@&@READ
In a short time, the display is changed as follows.

UB99@SRAM@CHECK@
OK@PUSH[ONOFF]SW
Check for the OK sign in the display.
3-4. FLASH ROM Check
3-4-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@FLASH@ROM
NOW@WRITE@&@READ
In a short time, the display is changed as follows.

UB99@FLASH@ROM
OK@PUSH[ONOFF]SW
Check for the OK sign in the display.
3-5. SW&LED Check
3-5-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

3-5-4. Push [+] SW. The following display appears.

UB99@SW&LED@CHEK
PUSH@[STORE]@SW
Then, LED (+) will be turned on.
3-5-5. Push [STORE/EXIT] SW. The following display
appears.

UB99@SW&LED@CHEK
PUSH@[ON/OFF]@SW
Then, three LEDs, LED (-), LED [ON/OFF] or
[AUTO F.R./ON/OFF], and LED (+) will be turned
on.
Check for the OK sign in the display.
3-6. VR Check
3-6-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@VOL1@CHECK
MAX@[**]@**@@**@@
The LEDs will be turned off.
** represents each of VR values, and [] shows
the position of the VR to be inspected.

VR1

VR2

VR3

UB99@SW&LED@CHEK
PUSH@[-]@SWITCH
Check for the OK sign in the display.
Before checking, set each VR to center.
3-5-2. Push [-] SW. The following display appears.

UB99@SW&LED@CHEK
PUSH@[ON/OFF]@SW
and LED (-) will be turned on.
3-5-3. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@SW&LED@CHEK
PUSH@[+]@SWITCH

3-6-2. Turn VR1 (Control 1) fully clockwise. The following

display appears.

UB99@VOL1@CHECK
MIN@[ff]@@**@@**@
3-6-3. Turn VR1 (Control 1) fully counterclockwise. The
following display appears.

UB99@VOL1@CHECK
UP@@[00]@**@@**@@

Then, LED [ON/OFF] or [AUTO F.R./ON/OFF] will

be turned on.

15

UB99A/UB99B/UB99MK2
3-6-4. Turn VR1 (Control 1) to center. The following
display appears.

UB99@VOL2@CHECK
MAX@@**@[**]@**@@
3-6-5. Turn VR2 (Control 2) fully clockwise. The following
display appears.

UB99@VOL2@CHECK
MIN@@**@[ff]@**@@
3-6-6. Turn VR2 (Control 2) fully counterclockwise. The
following display appears.

UB99@VOL2@CHECK
UP@@@**@[00]@**@@
3-6-7. Turn VR2 (Control 2) to center. The following
display appears.

UB99@VOL3@CHECK
MAX@@**@@**@[**]
3-6-8. Turn VR3 (Control 3) fully clockwise. The following
display appears.

UB99@VOL3@CHECK
MIN@@**@@**@[ff]
3-6-9. Turn VR3 (Control 3) fully counterclockwise. The
following display appears.

UB99@VOL3@CHECK
UP@@@**@@**@[00]
3-6-10. Turn VR3 (Control 3) to center. The following
display appears.

UB99@VOL3@CHECK
OK@PUSH[ONOFF]SW
Check for the OK sign in the display.

16

3-7. USB Check

3-7-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@USB@CHECK
V10103@CNECT@USB
3-7-2. Connect with PC by USB cable. The following
display appears.

UB99@USB@CHECK
DISCONNECT@CABLE
3-7-3. Remove the USB cable. The following display
appears.

UB99@USB@CHECK
OK@PUSH[ONOFF]SW
Check for the OK sign in the display.
3-8. LCD Check
3-8-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@LCD@CHECK@@
PUSH@[ON/OFF]@SW
3-8-2. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~
All the LEDs will be turned on.
3-9. END
3-9-1. Push [ON/OFF] or [AUTO F.R./ON/OFF] SW. The
following display appears.

UB99@DIAG@ALL@OK
PLEASE@POWER@OFF
Turn off power, and the inspection is now
completed.
Finally, perform 4. Factory Set as follows.

UB99A/UB99B/UB99MK2
4.

Factory Set

Turn off power, and the inspection is now completed. If you

reset UB99A/ UB99B/ UB99MK2 to the factory default setting,
all of the batch contents you saved are erased. Take notes of
the settings, or save the settings on your computer, if
necessary (See page 22).
4-1. Turn on power while pushing [ON/OFF] or [AUTO
F.R./ON/OFF] SW and [STORE/EXIT] SW. The
following display appears.

@@FACTORY@@SET
@NO:[-]@YES:[+]

5.

Opening
In this mode, the following display appears.

@@@MAGICSTOMP@@@
@@@@@V2.00
(This picture shows an example of UB99MK2.)

* V2.00 indicates the version of the firmware. This

number is subject to change due to the specification
change.
Then, the display is changed as follows.

@\
WAIT@A@MOMENT...

4-2. Push [+] SW. The following display appears.

@@FACTORY@@SET
SURE?PUSH[STORE]
4-3. Push [STORE/EXIT] SW. The following display
appears.

@@FACTORY@@SET
NOW@FACTORY@SET!

Finally, the display is changed as follows.

U01)HeavyHiGain
@@GAIN@MSTR@TONE
(This picture shows an example of UB99MK2.)

Turn off power and finish the procedure.

Then, the display is changed as follows.

@@FACTORY@@SET
@@@COMPLETE!!@@@
The Factory Set is completed.
Then, 5.Opening display will appear and operation
returns to a normal condition.
4-4. At the time of cancellation, the following display
appears.

@@FACTORY@@SET
@@@CANCELLED!@@@

17

UB99A/UB99B/UB99MK2

/
1.

3-2-2.

1-1.

1-2.
USB P.C.
1-3.

INPUT LEVEL

SW

1:

INPUT
-4.5 dBm (1 KHz)

INPUT Signal Input

OUT L/
RL 47 K
MONO
OUT R RL 47 K

2:

INPUT
-4.5 dBm (10 KHz)

OUT L/MONO
0 dBm 3 dB

3:

INPUT
-4.5 dBm (100 Hz)

OUT L/MONO
0 dBm 3 dB

PHONES RL 33

4:

INPUT
OUT R
-22.5 dBm (100 Hz) 0 dBm 3 dB

5:

INPUT
-22.5 dBm (10
KHz)

OUT R
0 dBm 3 dB

6:

INPUT
-22.5 dBm (1 KHz)

OUT R
0 dBm 3 dB

7:

INPUT
-13.5 dBm (1 KHz)

PHONES R
0 dBm 3 dB

8:

INPUT
-13.5 dBm (10
KHz)

PHONES R
0 dBm 3 dB

9:

INPUT
PHONES R
-12.5 dBm (100 Hz) 0 dBm 3 dB

AC IN

AC (AC-10)

USB
INPUT
LEVEL

USB P.C.
HIGH +10dB / LOW 0dB
LOW

2.

1KHz
Control VR1 Control VR2
Control VR3
VOLUME VR INPUT LEVEL SW LOW

1M

P.C. USB-MIDI

3.

3-1. TEST MODE

3-1-1. [ ] SW [ ] SW
TEST MODE
AC

[email protected]@V1.0@
PUSH@[ON/OFF]@SW

LCD LED

3-2. DSP & DRAM & AD/DA Check
3-2-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@DSP&DRAM@
PUSH@[ON/OFF]@SW

18

HIGH

OUT L/MONO
0 dBm 3 dB

10:

INPUT
+5.5 dBm (100 Hz)

PHONES L
0 dBm 3 dB

11:

INPUT
+4.5 dBm (10 kHz

PHONES L
0 dBm 3 dB

12:

INPUT
+4.5 dBm (1 kHz)

PHONES L
0 dBm 3 dB

13:

INPUT
-15 dBm (1 KHz)

OUT L/MONO
0 dBm 3 dB

14:

INPUT

OUT L/MONO
-44 dBm

15:

INPUT

OUT R
-44 dBm

16:

INPUT

PHONES L
-52 dBm

17:

INPUT

PHONES R
-52 dBm

18:

INPUT
-12 dBm (1 KHz)

OUT R
0.5%

19:

INPUT
+6 dBm (1 KHz)

OUT L/MONO
0.5%

20:

INPUT
+8 dBm (1 KHz)

PHONES L
0.5%

21:

INPUT
-10 dBm (1 KHz)

PHONES R
0.5%

0 dBm=0.775 V

INPUT LEVEL SW LOW

UB99A/UB99B/UB99MK2
3-3. SRAM Check
3-3-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

3-5-4.

UB99@SW&LED@CHEK
PUSH@[STORE]@SW

UB99@SRAM@CHECK@
NOW@WRITE@&@READ

LED +
3-5-5.

UB99@SRAM@CHECK@
OK@PUSH[ONOFF]SW

UB99@FLASH@ROM
NOW@WRITE@&@READ

[STORE/EXIT] SW

UB99@SW&LED@CHEK
PUSH@[ON/OFF]@SW

OK
3-4. FLASH ROM Check
3-4-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

[+] SW

LED ( ) LED (ON/OFF AUTO

F.R./ON/OFF) LED (+) 3
OK
3-6. VR Check
3-6-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@VOL1@CHECK
MAX@[**]@**@@**@@

UB99@FLASH@ROM
OK@PUSH[ONOFF]SW

LED
**VR [ ]
VR

OK
VR1

VR2

VR3

3-5. SW&LED Check

3-5-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@SW&LED@CHEK
PUSH@[-]@SWITCH
VR

3-5-2.

[ ] SW

3-6-2.

UB99@SW&LED@CHEK
PUSH@[ON/OFF]@SW

UB99@VOL1@CHECK
MIN@[ff]@@**@@**@

LED ( )
3-5-3.

[ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@SW&LED@CHEK
PUSH@[+]@SWITCH

VR1 (Control 1)

3-6-3.

VR1 (Control 1)

UB99@VOL1@CHECK
UP@@[00]@**@@**@@

LED ON/OFF AUTO F.R./ON/

OFF

19

UB99A/UB99B/UB99MK2
3-6-4.

VR1 (Control 1)

UB99@VOL2@CHECK
MAX@@**@[**]@**@@

3-7. USB Check

3-7-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@USB@CHECK
V10103@CNECT@USB

3-6-5.

VR2 (Control 2)

UB99@VOL2@CHECK
MIN@@**@[ff]@**@@

3-7-2.

UB99@USB@CHECK
DISCONNECT@CABLE

3-6-6.

VR2 (Control 2)

UB99@VOL2@CHECK
UP@@@**@[00]@**@@

3-7-3.

VR2 (Control 2)

UB99@VOL3@CHECK
MAX@@**@@**@[**]

OK
3-8. LCD Check
3-8-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

3-6-8.

UB99@LCD@CHECK@@
PUSH@[ON/OFF]@SW

VR3 (Control 3)

UB99@VOL3@CHECK
MIN@@**@@**@[ff]

3-8-2.

3-6-9.

VR3 (Control 3)

UB99@VOL3@CHECK
UP@@@**@@**@[00]

3-6-10. VR3 (Control 3)

UB99@VOL3@CHECK
OK@PUSH[ONOFF]SW
OK

USB Cable

UB99@USB@CHECK
OK@PUSH[ONOFF]SW

3-6-7.

USB Cable P.C.

[ON/OFF] [AUTO F.R./ON/OFF] SW

~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~

3-9. END
3-9-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

UB99@DIAG@ALL@OK
PLEASE@POWER@OFF

OFF

4.

20

UB99A/UB99B/UB99MK2
4.

P.22

5.

@@@MAGICSTOMP@@@
@@@@@V2.00
UB99MK2

4-1. [ON/OFF] [AUTO F.R./ON/OFF] SW

[STORE/EXIT] SW ON

@@FACTORY@@SET
@NO:[-]@YES:[+]

4-2. [+] SW

@@FACTORY@@SET
SURE?PUSH[STORE]

V2.00

@\
WAIT@A@MOMENT...

U01)HeavyHiGain
@@GAIN@MSTR@TONE
UB99MK2

4-3. [STORE/EXIT] SW

@@FACTORY@@SET
NOW@FACTORY@SET!

@@FACTORY@@SET
@@@COMPLETE!!@@@

.
4-4.

@@FACTORY@@SET
@@@CANCELLED!@@@

21

UB99A/UB99B/UB99MK2

BACKUP THE USER PATCH DATA

1. Using the USB cable, connect the computer to the
MAGICSTOMP, then turn on the computer and the
MAGICSTOMP.
2. Insert the CD-ROM (*1) into your computer.
3. Start the Sound Editor for MAGICSTOMP.
4. Click on the Bulk Receive button on the tool bar, and
then click the Start button.

1. MAGICSTOMP USB
MAGICSTOMP
2. CD-ROM 1
3. Sound Editor for MAGICSTOMP
4.

Bulk Receive Button

5. The contents of the MAGICSTOMPs User Patch

memory are transferred to the computer. The
MAGICSTOMPs display will indicate how much data has
been transferred.

5. MAGICSTOMP
MAGICSTOMP

@@BULK@OUT@ALL!
@@NOW@PATCH:59@@@

22

6. The Bulk Receive operation is complete when the

contents of the MAGICSTOMPs User Patch memory
appears in the library window.
7. Click on the Close button to close the Bulk Receive
dialog box.
8. Click on the Save button to give the file a name and
store the data in the computer. This is your backup file.

6. MAGICSTOMP

7.

8.

*1: Please use the CD-ROM numbered as follows:

UB99A:
X4770A00
UB99B:
X5906A00
UB99MK2
X4770A00

1 CD-ROM
UB99A
X4770A00
UB99B
X5906A00
UB99MK2 X4770A00

UB99A/UB99B/UB99MK2

ERROR MESSAGES
One of the following messages may appear in the MAGICSTOMPs display if an error occurs during operation. If so, please
stop operation and check the following points to find a solution to the problem.
.

@@BAD@DATA:U**
@@PUSH@ANY@KEY

The data being bulk transmitted is damaged. After restoring (overwrite, store, etc.) the user
patch data that corresponds to the patch number, try transmitting the data again.

@@@MIDI@ERROR!
@@PUSH@ANY@KEY

An error occurred while transmitting data. Check the USB cable connection, computer
settings, etc.

@@BULK@@ERROR!
@@PUSH@ANY@KEY

An error occurred while transmitting or receiving bulk data. Check the USB cable connection.
Also, if the error occurs about halfway through the operation, setting the interval speed to a
slower setting sometimes solves the problem.

@@@USB@ERROR!
@@PUSH@ANY@KEY

The hardware is damaged.

MAGICSTOMP

@@BAD@DATA:U**
@@PUSH@ANY@KEY

( )

@@@MIDI@ERROR!
@@PUSH@ANY@KEY

USB

@@BULK@@ERROR!
@@PUSH@ANY@KEY

USB
( )

@@@USB@ERROR!
@@PUSH@ANY@KEY

23

ACOUSTIC EFFECTS PROCESSOR

BASS EFFECTS PROCESSOR
GUITAR EFFECTS PROCESSOR

UB99A/UB99B/UB99MK2
PARTS LIST

CONTENTS

OVERALL ASSEMBLY................................................................................. 2
TOP CASE ASSEMBLY Assy........................................................... 3
ELECTRICAL PARTS............................................................................ 4-8

Notes : DESTINATION ABBREVIATIONS

A:
B:
C:
D:
E
F:
H:
I:
J:
K:

Australian model
British model
Canadian model
German model
European model
French model
North European model
Indonesian model
Japanese model
Korean model

M:
O:
Q:
T:
U:
V:
W:
N,X:
Y:

South African model

Chinese model
South-east Asia model
Taiwan model
U.S.A. model
General export model (110V)
General export model (220V)
General export model
Export model

WARNING

Components having special characteristics are marked

specification equal to those originally installed.

and must be replaced with parts having

The numbers QTY show quantities for each unit.

The parts with -- in PART NO. are not available as spare parts.
This mark } in the REMARKS column means these parts are interchangeable.
The second letter of the shaded (
) part number is O, not zero.
The second letter of the shaded (
) part number is I, not one.

QTY
PART NO. --
REMARKS
PART NO. 2
PART NO. 2

UB99A/UB99B/UB99MK2

OVERALL ASSEMBLY
Top case Assembly: (See page 3.)
Ass'y3

60

10
60

20

30

50
50
40

AC-10

REF NO. PART NO.

---10
-10
-10
-20
*
WD906500
20
*
WE124400
20
*
WD906600
30
EP600190
40
VB931600
50
WB845100
60
WB845200

V5883000
V5883100
X4770A00
X5906A00
X4770A00
WB930000

*: New Parts
2

AC Output Power Adaptor

AC

DESCRIPTION
OVERALL ASSEMBLY
OVERALL ASSEMBLY
OVERALL ASSEMBLY
Top Case Assembly
Top Case Assembly
Top Case Assembly
Bottom Case
Bottom Case
Bottom Case
Bind Head Tapping Screw-B
3.0X8 MFZN2BL
Bind Head Tapping Screw-P
4.0X8 MFZN2BL
Foot
Knob Black

ACCESSORIES
AC Adaptor
AC Adaptor
CD-ROM
CD-ROM
CD-ROM
USB Cable

AC-10 U,C
AC-10 H
CD-ROM 12cm #4A78
CD-ROM 12cm #4A91
CD-ROM 12cm #4A78
4P 1.5m USB(A-B)

UB99A
UB99B
UB99MK2
UB99A
UB99B
UB99MK2
UB99A
UB99B
UB99MK2

REMARKS
QTY RANK
(WD90520)
(WD98920)
(WD90530)
(WD90630)
(WD99000)
(WD90640)

CONTROL 1-3, VOLUME

U,C
H
UB99A
UB99B
UB99MK2

2
4
4
4

01
01
01
01

08
08
04
04
04

RANK: Japan only

UB99A/UB99B/UB99MK2

TOP CASE ASSEMBLY Assy

20
150
40

110

80
120

60

130

70
10

30
100
140

90
50
40

*
*
*
*
*
*
*
*

*
*
*

*
*

REF NO. PART NO.

---10
WD906700
10
WE124500
10
WD906800
20
WD906900
20
WE124600
20
WD952700
30
WD907000
30
WE124700
30
WB845800
40
WB842500
50
WB842900
60
ET500230
70
WD894900
70
WE164000
70
WD958700
80
WB845700
90
EP630220
100 WD907200
100 WE124800
100 WB845900
110 VA295800
120 LX200060
130 VL802300
140 ET800150
150 WC497400

*: New Parts

DESCRIPTION
TOP CASE ASSEMBLY
UB99A
TOP CASE ASSEMBLY
UB99B
TOP CASE ASSEMBLY
UB99MK2
Top Case
Top Case
Top Case
Panel Sheet
t=1.0
Panel Sheet
t=1.0
Panel Sheet
t=1.0
Foot Switch Panel
t=1.2
Foot Switch Panel
t=1.2
Foot Switch Panel
t=1.2
Foot Switch
ALPHA SF12030
Spring Washer
12X15 MFZN2Y
Flat Washer
12.0X16X0.5 MFNI33
Circuit Board
DM
Circuit Board
DM
Circuit Board
DM
Key Top Black
Bind Head Tapping Screw-P
3.0X8 MFZN2BL
Rear Panel
t=1.6
Rear Panel
t=1.6
Rear Panel
t=1.6
Bind Head Screw
3.0X8 MFZN2BL
Hexagonal Nut
9.0 12X2 MFNI33
Flat Washer
9.0X14X0.5 MFNI33
Toothed Lock Washer-A
9.0 MFZN2Y
AC Cord Column

REMARKS
QTY RANK
UB99A
(WD90630)
UB99B
(WD99000)
UB99MK2
(WD90640)
UB99A
UB99B
UB99MK2
UB99A
UB99B
UB99MK2
UB99A
UB99B
UB99MK2
04
-,ON/OFF,+
3
05
3
3
01
UB99A
UB99B
UB99MK2
STORE
01
8
01
UB99A
UB99B
UB99MK2
03
01
3
01
3
01
3
01

RANK: Japan only

UB99A/UB99B/UB99MK2

ELECTRICAL PARTS
REF NO. PART NO.
*
*
*
*
*
*

C0001
-0004
C0005
C0006
C0007
C0008
C0009
C0010
C0011
C0012
C0013
C0014
-0018
C0019
C0020
-0028
C0029
C0030
-0037
C0038
C0039
-0041
C0101
C0102
C0103
C0104
C0105
C0106
C0107
C0108
C0109
C0110
C0111
C0112
C0113
C0114
-0118
C0119
C0120
C0121
C0122
C0123
-0125
C0126
C0127
C0128
C0129
C0130
C0131
C0132
C0133
C0134
C0135
C0136
C0137
C0138
C0139

DM
DM
DM

WD894900
WE164000
WD958700
WB843600
WB843700
VB763800
WB843500
WB929700
US145100
US145100
UI528100
US145100
UI528100
US145100
US145100
US061100
US061100
US061270
US061270
US145100
US145100
UI528100
US145100
US145100
UI528100
US145100
US145100
UI528100
US145100
US145100
UY065220
US062100
UR847100
V4587500
V4587500
US061100
US145100
US145100
US062100
US063150
US062100
US062100
US063150
UR847100
UR847100
US145100
UR866220
US145100
UR847100
US145100
US145100
US062470
US062470
US063330
V4587500
UR847100
US061220
V4587500
V4587500
US062100
US063330
US062470
US062470
V4587500
V4587500

DM
DM
DM
PINGOOD MCD2-5
PINGOOD LED3-18
SP 3.0X12 MFZN2Y
M3X15
EC016002S
0.1000 25V Z
0.1000 25V Z
100.00 10.0V
0.1000 25V Z
100.00 10.0V
0.1000 25V Z
0.1000 25V Z
10P 50V D
10P 50V D
27P 50V J
27P 50V J
0.1000 25V Z
0.1000 25V Z
100.00 10.0V
0.1000 25V Z
0.1000 25V Z
100.00 10.0V
0.1000 25V Z
0.1000 25V Z
100.00 10.0V
0.1000 25V Z
0.1000 25V Z
0.2200 50V Z
100P 50V J
10.00 25.0V
10.00 25.0V
10.00 25.0V
10P 50V D
0.1000 25V Z
0.1000 25V Z
100P 50V J
1500P 50V K
100P 50V J
100P 50V J
1500P 50V K
10.00 25.0V
10.00 25.0V
0.1000 25V Z
2.20 50.0V
0.1000 25V Z
10.00 25.0V
0.1000 25V Z
0.1000 25V Z
470P 50V J
470P 50V J
3300P 50V K
10.00 25.0V
10.00 25.0V
22P 50V J
10.00 25.0V
10.00 25.0V
100P 50V J
3300P 50V K
470P 50V J
470P 50V J
10.00 25.0V
10.00 25.0V

UB99A

UB99B

UB99MK2

Circuit Board
Circuit Board
Circuit Board
Spacer Support
LED Holder
Bind Head Screw
Hexagonal Nut
LCD
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor-CH(chip)
Ceramic Capacitor-CH(chip)
Ceramic Capacitor-CH(chip)
Ceramic Capacitor-CH(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor(chip)
Ceramic Capacitor-SL(chip)
Electrolytic Cap.
Electrolytic Cap.-NK
Electrolytic Cap.-NK
Ceramic Capacitor-CH(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-B(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-B(chip)
Electrolytic Cap.
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Electrolytic Cap.
Ceramic Capacitor-F(chip)
Ceramic Capacitor-F(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-B(chip)
Electrolytic Cap.-NK
Electrolytic Cap.
Ceramic Capacitor-CH(chip)
Electrolytic Cap.-NK
Electrolytic Cap.-NK
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-B(chip)
Ceramic Capacitor-SL(chip)
Ceramic Capacitor-SL(chip)
Electrolytic Cap.-NK
Electrolytic Cap.-NK

REMARKS
QTY RANK

(X5898A0)
UB99A
(X5898A0)
UB99B
(X5898A0)
UB99MK2

*: New Parts

DESCRIPTION

ELECTRICAL PARTS
WD894900 Circuit Board
WE164000 Circuit Board
WD958700 Circuit Board

(X5898A0)
(X5898A0)
(X5898A0)
4
3
2
2

01
09
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01

RANK: Japan only

UB99A/UB99B/UB99MK2
REF NO.
C0140
C0141
C0142
C0143
C0144
C0145
C0146
-0148
C0149
C0150
C0151
C0152
C0153
C0154
C0155
C0156
C0157
C0159
C0160
C0161
C0162
C0163
C0164
C0165
C0166
C0167
C0168
C0169
C0170
C0171
C0172
C0173
C0174
C0175
C0176
C0177
C0178
-0187
C0188
C0189
C0190
C0191
C0192
C0193
C0194
C0195
C0196
C0197
CN001
D0101
-0105
D0106
-0112
* IC001
* IC001
* IC001
IC002
IC002
IC002
IC003
IC004
IC005
IC006
IC007
IC008
IC009
IC010
IC101
IC102
IC103
IC104
IC105
IC106
IC107
IC108

PART NO.
UR847100
US061220
V4587500
US062100
UR847100
UR847100
US145100
US145100
UI528100
UY065100
UY065100
UR649220
US145100
US145100
UR829100
UR866100
UR866100
UR866470
UR848470
UR848470
UR868470
UR868470
UY065100
UY065100
US145100
US145100
UR848470
UR848220
US145100
US145100
UI528100
US060500
US060500
US145100
UR847100
UR847100
US145100
US145100
US061220
UR847100
VN509700
US063100
US061220
UR847100
VN509700
US063100
UR847100
UR847100
WB288800
VT332900
VT332900
VT532500
VT532500
X5929A00
X6082A00
X5963A00
X4386A00
X4388A00
X4390A00
X0009A00
X4196A00
XV988B00
X2726A00
X3921200
X3693A00
X3693A00
X2726A00
XC458A00
X4980A00
X4980A00
XY624A00
X4980A00
X4980A00
X3936A00
XS534A00

*: New Parts

DESCRIPTION
Electrolytic Cap.
10.00 25.0V
Ceramic Capacitor-CH(chip)
22P 50V J
Electrolytic Cap.-NK
10.00 25.0V
Ceramic Capacitor-SL(chip)
100P 50V J
Electrolytic Cap.
10.00 25.0V
Electrolytic Cap.
10.00 25.0V
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Electrolytic Cap.
100.00 10.0V
Ceramic Capacitor(chip)
0.1000 50V Z
Ceramic Capacitor(chip)
0.1000 50V Z
Electrolytic Cap.
2200 25.0V
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Electrolytic Cap.
1000 10.0V
Electrolytic Cap.
1.00 50.0V
Electrolytic Cap.
1.00 50.0V
Electrolytic Cap.
4.70 50.0V
Electrolytic Cap.
470.00 25.0V
Electrolytic Cap.
470.00 25.0V
Electrolytic Cap.
470.00 50.0V
Electrolytic Cap.
470.00 50.0V
Ceramic Capacitor(chip)
0.1000 50V Z
Ceramic Capacitor(chip)
0.1000 50V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Electrolytic Cap.
470.00 25.0V
Electrolytic Cap.
220.00 25.0V
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Electrolytic Cap.
100.00 10.0V
Ceramic Capacitor-CH(chip)
5P 50V C
Ceramic Capacitor-CH(chip)
5P 50V C
Ceramic Capacitor-F(chip)
0.1000 25V Z
Electrolytic Cap.
10.00 25.0V
Electrolytic Cap.
10.00 25.0V
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-F(chip)
0.1000 25V Z
Ceramic Capacitor-CH(chip)
22P 50V J
Electrolytic Cap.
10.00 25.0V
Bipolar Electrolytic Cap.
22.00 25.0V
Ceramic Capacitor-B(chip)
1000P 50V K
Ceramic Capacitor-CH(chip)
22P 50V J
Electrolytic Cap.
10.00 25.0V
Bipolar Electrolytic Cap.
22.00 25.0V
Ceramic Capacitor-B(chip)
1000P 50V K
Electrolytic Cap.
10.00 25.0V
Electrolytic Cap.
10.00 25.0V
Pin Header
2.54mm 16P
Diode
1SS355 TE-17
Diode
1SS355 TE-17
Diode
1SR154-400
Diode
1SR154-400
IC
M29LV160BBTC-70G
IC
M29LV160BBTC-70G
IC
M29LV160BBTC-70G
IC
BS62LV256TC-70
IC
IS62LV256-70T
IC
CY62256VLL-70ZCT
IC
S-80128BNMC-JGN
IC
HD6413008VF25
IC
YSS910-V
IC
GLT440L16-40TC
IC
M38K07M4L-303HP
IC
SN74LV245APWR
IC
SN74LV245APWR
IC
GLT440L16-40TC
IC
NJM072M
IC
NJM5532M-TE1
IC
NJM5532M-TE1
IC
AK4528VF
IC
NJM5532M-TE1
IC
NJM5532M-TE1
IC
SN74LVU04APWR
IC
NJM78M05DL1A(TE1)

REMARKS

QTY RANK
01
01
01
01
01
01
01
01
01
01
01
02
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01

UB99A, FLASH ROM 16M PROGRAM

UB99B, FLASH ROM 16M PROGRAM
UB99MK2, FLASH ROM 16M PROGRAM
08
SRAM 256K
SYSTEM RESET
CPU(MAIN)
DSP6
DRAM 4M
CPU(USB)
TRANSCEIVER
TRANSCEIVER
DRAM 4M
OP AMP
OP AMP
OP AMP
ADC/DAC
OP AMP
OP AMP
INVERTER
REGULATOR +5V

01
08
09
05
10

05
03
03
03
08
03
03
02

RANK: Japan only

UB99A/UB99B/UB99MK2
REF NO.
IC109
IC110
IC111
IC112
IC113
IC114
JK001
JK101
JK102
JK103
JK104
JK105
K0101
L0001
-0003
L0101
LD001
LD002
LD003
R0001
R0002
R0003
R0004
R0005
R0006
R0007
R0008
R0009
R0010
R0011
R0012
R0013
R0014
R0015
R0016
R0017
R0018
R0019
R0020
R0021
R0022
R0023
R0024
R0025
R0026
R0027
R0028
R0029
R0030
-0032
R0033
-0060
R0061
-0068
R0069
-0080
R0081
R0082
R0101
R0102
R0103
R0104
R0105
R0106
R0107
R0108
R0109
R0110
R0111
R0112
R0113
R0114
R0115
R0116
R0117

PART NO.
XS534A00
X3935A00
XU965A00
XD853A00
XD854A00
X5049A00
WC314200
V3633400
V6177700
V6177700
V6177200
V7447000
VV075700
VS740100
VS740100
VH746100
WB990700
WB990700
WB990700
RD355100
RD357100
RD355100
RD153470
RD355270
RD357100
RD357100
RD355220
RD357100
RD358100
RD355220
RD357100
RD358100
RD355220
RD357100
RD358100
RD357330
RD355560
RD354270
RD354270
RD356220
RD356270
RD357470
RD356100
RD354680
RD354680
RD356100
RD357100
RD356150
RD357470
RD357470
RD355100
RD355100
RD359100
RD359100
RD250000
RD250000
RD355100
RD355100
RD357100
RD359100
RD356470
RD356470
RD357220
RD357120
RD357100
RD357100
RF457100
RF457220
RF456330
RD356470
RD356470
RD355330
RD355330
RF457100
RF455470

*: New Parts
6

IC
IC
IC
IC
IC
IC
USB Connector
Phone Jack
Phone Jack
Phone Jack
Connector
Phone Connector
Terminal Plate
Chip Inductance
Chip Inductance
Choke Coil
LED Red
LED Red
LED Red
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)
Carbon Resistor (chip)

DESCRIPTION
NJM78M05DL1A(TE1)
SN74LV4040APWR
UPC29M33T-E1 3.3V
NJM7815FA
NJM7915FA
NJM4556AM-TE1
WTEA04006 SE 4P
HTJ-064-12I
STEREO HTJ-064-12D
STEREO HTJ-064-12D
SOCKET HTJ-020-05A
ST MINI HTJ-035-09

BLM21B751S 2125

BLM21B751S 2125

PLT09HN2003R0P1B 20uH
LT0311-41-XA300089

LT0311-41-XA300089

LT0311-41-XA300089

100.0 63M J

10.0K 63M J

100.0 63M J

4.7 1/4 J

270.0 63M J

10.0K 63M J

10.0K 63M J

220.0 63M J

10.0K 63M J

100.0K 63M J

220.0 63M J

10.0K 63M J

100.0K 63M J

220.0 63M J

10.0K 63M J

100.0K 63M J

33.0K 63M J

560.0 63M J

27.0 63M J

27.0 63M J

2.2K 63M J

2.7K 63M J

47.0K 63M J

1.0K 63M J

68.0 63M J

68.0 63M J

1.0K 63M J

10.0K 63M J

1.5K 63M J

47.0K 63M J

47.0K 63M J

100.0 63M J

100.0 63M J

1.0M 63M J

1.0M 63M J

0.0 0.0 J

0.0 0.0 J

100.0 63M J

100.0 63M J

10.0K 63M J

1.0M 63M J

4.7K 63M J

4.7K 63M J

22.0K 63M J

12.0K 63M J

10.0K 63M J

10.0K 63M J

10.0K D

22.0K D

3.3K D

4.7K 63M J

4.7K 63M J

330.0 63M J

330.0 63M J

10.0K D

470.0 D

REMARKS
REGULATOR +5V
BINARY COUNTER
REGULATOR +3.3V
REGULATOR +15V
REGULATOR -15V
OP AMP
USB
INPUT
OUTPUT R
OUTPUT L/MONO
AC IN
PHONES

QTY RANK
02
03
03
03
02
01
03
03
03
02
01
03
03
04

ON/OFF
+
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01

RANK: Japan only

UB99A/UB99B/UB99MK2
REF NO.
R0118
R0119
R0120
R0121
R0122
R0123
R0124
R0125
R0126
-0129
R0130
R0131
R0132
R0133
R0134
R0135
R0136
R0137
R0138
R0139
R0140
R0141
-0144
R0145
R0146
R0147
R0148
R0149
R0150
R0151
R0152
R0153
R0154
R0155
R0156
R0157
R0158
R0159
R0160
R0161
R0162
R0163
R0164
R0165
R0166
R0167
-0170
R0171
R0172
R0173
R0174
R0175
R0176
R0177
R0178
R0179
R0180
R0181
R0182
R0183
R0184
R0185
R0186
RA001
-010
SW001
SW002
SW003
SW004
SW101
TR001
-004
TR005
TR101
-104

PART NO.
RF456270
RD356470
RD356470
RD355330
RD355330
RD356330
RD356470
RD153470
RD356470
RD356470
RD355200
RD355200
RD356100
RD357100
RD356100
RD358100
RD356220
RD357100
RD355470
RD357100
RD358100
RD356470
RD356470
RD355200
RD355200
RD356100
RD357100
RD356100
RD358100
RD356220
RD357100
RD355470
RD357100
RD358100
RD356220
RD356220
RD357100
RD358100
RD357220
RD358100
RD356220
RD358100
RD358100
RD355680
RD355220
RD355100
RD355100
RD359100
RD355470
RD357100
RD355470
RD357100
VC744600
VC744600
VC757300
RD357100
RD356100
RD155150
RD358100
RD357100
RD356100
RD155150
RD358100
RE047100
RE047100
KA901660
KA901660
KA901660
WC330800
WC402300
VV556400
VV556400
VJ927200
VD303700
VD303700

*: New Parts

DESCRIPTION
Carbon Resistor (chip)
2.7K D
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
330.0 63M J
Carbon Resistor (chip)
330.0 63M J
Carbon Resistor (chip)
3.3K 63M J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
4.7 1/4 J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
200.0 63M J
Carbon Resistor (chip)
200.0 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
2.2K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
470.0 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
4.7K 63M J
Carbon Resistor (chip)
200.0 63M J
Carbon Resistor (chip)
200.0 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
2.2K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
470.0 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
2.2K 63M J
Carbon Resistor (chip)
2.2K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
22.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
2.2K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
680.0 63M J
Carbon Resistor (chip)
220.0 63M J
Carbon Resistor (chip)
100.0 63M J
Carbon Resistor (chip)
100.0 63M J
Carbon Resistor (chip)
1.0M 63M J
Carbon Resistor (chip)
470.0 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
470.0 63M J
Carbon Resistor (chip)
10.0K 63M J
Metal Oxide Film Resistor
68.0 1W J
Metal Oxide Film Resistor
68.0 1W J
Metal Oxide Film Resistor
27.0 2W J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
150.0 1/4 J
Carbon Resistor (chip)
100.0K 63M J
Carbon Resistor (chip)
10.0K 63M J
Carbon Resistor (chip)
1.0K 63M J
Carbon Resistor (chip)
150.0 1/4 J
Carbon Resistor (chip)
100.0K 63M J
Resistor Array
10KX4
Resistor Array
10KX4
Push Switch
SKHCABA010
Push Switch
SKHCABA010
Push Switch
SKHCABA010
Tact Switch
TAA-4PV073-130
Slide Switch
SSSF122NA2-AA
Transistor
2SC2412K Q,R,S
Transistor
2SC2412K Q,R,S
Transistor
2SA1162 O,Y
Transistor
2SC3326 A,B TE85R
Transistor
2SC3326 A,B TE85R

REMARKS

ON/OFF,AUTO F.R.
+
STORE/EXIT
INPUT LEVEL HIGH/LOW

QTY RANK
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
02
02
02
01
02
01
01
01
01
01

RANK: Japan only

UB99A/UB99B/UB99MK2
REF NO.
TR105
TR106
TR107
TR108
VR001
VR002
VR003
VR101
X0001
X0002
X0003
X0101
ZD101
ZD102
ZD103
ZD104

PART NO.
VV556400
VJ927200
VD303700
VD303700
WB445700
WB445700
WB445700
WB446200
WA692500
WC402600
WC402500
WC402400
V9242500
V9242500
VU173000
VU173000

DESCRIPTION
Transistor
2SC2412K Q,R,S
Transistor
2SA1162 O,Y
Transistor
2SC3326 A,B TE85R
Transistor
2SC3326 A,B TE85R
Rotary Variable Resistor
RD09L1140 10KB
Rotary Variable Resistor
RD09L1140 10KB
Rotary Variable Resistor
RD09L1140 10KB
Rotary Variable Resistor
RD09L12D0 10KA X2
Quartz Crystal Unit
30.0MHz SMD5X7SPXO
Quartz Crystal Unit
16.0MHz HC-49SMD
Quartz Crystal Unit
6.0MHz HC-49SMD
Quartz Crystal Unit
22.5792MHz HC-49SMD
Zener Diode
HZU2.0B 2.0V
Zener Diode
HZU2.0B 2.0V
Zener Diode
UDZS 15B TE-17 15V
Zener Diode
UDZS 15B TE-17 15V

V5883000 AC Adaptor
V5883100 AC Adaptor

*: New Parts
8

AC-10 U,C
AC-10 H

REMARKS

CONTROL 1
CONTROL 2
CONTROL 3
VOLUME

U,C
H

QTY RANK
01
01
01
01
03
03
03
03

01
01
08
08

RANK: Japan only

UB99A/UB99B/UB99MK2 DM CIRCUIT DIAGRAM 1/2

( ): Ceramic Capacitor ( )
: Metal Oxide Film Resistor ( )

UB99A/UB99B/UB99MK2

1
FLASH ROM 16M
PROGRAM

TRANSCEIVER

SRAM 256K

STORE/EXIT

SYSTEM
RESET

+
AUTO F.R./ON/OFF (*1)
ON/OFF ( 2)

to Page 1: G4
to Page 2: G3

CPU (MAIN)
TRANSCEIVER

from Page 1: D3

AUTO F.R./ON/OFF (*1)

from Page 2: C5
from Page 2: E5

CPU (USB)

ON/OFF (*2)

DRAM 4M
from Page 2: F4

(USB)

*1 indicates the name for the UB99A model.

*1 UB99A
*2 indicates the name for the UB99B/
UB99MK2 models.
*2 UB99B/UB99MK2

DSP 6
to Page 2: F4

CONTROL 1

CONTROL 3
CONTROL 2

DRAM 4M

Notation for Circuit Diagrams

How to identify inter-sheet connectors.
RESET

to page 1: G4

Signal name

UB99A:
UB99B:
UB99MK2:

DIC-00013-2
DIC-00021-2
DIC-00016-2

This indicates the location of the counter inter-sheet connector.

(The alphabet indicates horizontal direction and the number indicates vertical direction)

The page number indicates the destination page.

No.

UB99A/UB99B/UB99MK2 DM CIRCUIT DIAGRAM 2/2

1

( )Ceramic Capacitor ( )
Metal Oxide Film Resistor ( )
1/16 WCarbon Resistor (chip) ( )

UB99A/UB99B/UB99MK2

INPUT LEVEL SELECT SW.

LOW

HIGH

OP AMP
OUTPUT R

OP AMP

INPUT

OP AMP

OP AMP

OP AMP
OP AMP

OP
AMP

VOLUME

from Page 1: D3

PHONES

ADC/DAC
OP AMP

OP AMP

OP AMP
OP AMP

OP AMP

from Page 1: A5
to Page 1: A5

OP AMP

OP AMP

REGULATOR +5V

INVERTER
BINARY
COUNTER

OUTPUT L/MONO

OP AMP
to Page 1: A4

REGULATOR +5V
MUTE

to Page 1: A4

NJM7815FA(XD853A00)
REGULATOR +15V
DM: IC112

NJM78M05DLA(XS534A00)
REGULATOR +5V
DM: IC108, 109

PC29M33T-E1(XU965A00)
REGULATOR +3.3V
DM: IC111
2

REGULATOR +3.3V

6
AC IN

REGULATOR +15V

Critical Components Information

1: INPUT
2: GND
3: OUTPUT
1SR154-400 (VT532500)
DIODE
DM: D106-112

1: INPUT
2: COMMON
3: OUTPUT
NJM7915FA(XD854A00)
REGULATOR -15V
DM: IC113

32

1: ANODE
2: CATHODE

REGULATOR -15V

DIC-00013-3
DIC-00021-3
DIC-00016-3

1
3

Components having special characteristics are marked

and must be replaced with parts having
specifications equal to those originally installed.

UB99A:
UB99B:
UB99MK2:

1: OUTPUT
2: COMMON
3: INPUT

TO SERVICE PERSONNEL

32

1: OUTPUT
2: INPUT
3: COMMON