Scribd Logo
Upload

Welcome to Scribd!

  • 78 views

    OptimunG Springs&Dampers Tech Tip 2

    Uploaded by

    Thomas Moura
    This document discusses calculating spring rates and anti-roll bar stiffness for vehicle suspension setup. It emphasizes the importance of using consistent units when performing calculations to avoid errors. Equations are provided to calculate spring rates based on sprung mass and ride frequency, as well as equations for determining front and rear anti-roll bar stiffness based on the desired roll gradient and distribution of roll stiffness between the front and rear. The document stresses that mass and weight are different units and should not be interchanged when calculating suspension parameters.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    OptimunG Springs&Dampers Tech Tip 2

    Uploaded by

    Thomas Moura
    78 views3 pages
    This document discusses calculating spring rates and anti-roll bar stiffness for vehicle suspension setup. It emphasizes the importance of using consistent units when performing calculations to avoid errors. Equations are provided to calculate spring rates based on sprung mass and ride frequency, as well as equations for determining front and rear anti-roll bar stiffness based on the desired roll gradient and distribution of roll stiffness between the front and rear. The document stresses that mass and weight are different units and should not be interchanged when calculating suspension parameters.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document discusses calculating spring rates and anti-roll bar stiffness for vehicle suspension setup. It emphasizes the importance of using consistent units when performing calculations to avoid errors. Equations are provided to calculate spring rates based on sprung mass and ride frequency, as well as equations for determining front and rear anti-roll bar stiffness based on the desired roll gradient and distribution of roll stiffness between the front and rear. The document stresses that mass and weight are different units and should not be interchanged when calculating suspension parameters.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    78 views3 pages

    OptimunG Springs&Dampers Tech Tip 2

    Uploaded by

    Thomas Moura
    This document discusses calculating spring rates and anti-roll bar stiffness for vehicle suspension setup. It emphasizes the importance of using consistent units when performing calculations to avoid errors. Equations are provided to calculate spring rates based on sprung mass and ride frequency, as well as equations for determining front and rear anti-roll bar stiffness based on the desired roll gradient and distribution of roll stiffness between the front and rear. The document stresses that mass and weight are different units and should not be interchanged when calculating suspension parameters.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Tech Tip: Springs & Dampers, Part Two

    Attack of the Units


    By Matt Giaraffa [email protected] After understanding last months tech tip, you know how to pick ride frequencies for your racecar, and calculate the spring rate needed for the chose frequency. Now, what do you do about the anti-roll bars. But first, we have had a couple emails asking about units and frequency calculations, so that will be explained further, and then we will explore how to develop baseline spring rates for anti-roll bars (ARBs).

    If you dont watch your units, you cant have any pudding.
    When calculating any parameters on the car, you must be sure the units are correct. Just because your physics teacher is not overseeing your calculations does not mean you can slack on the units. One of the biggest mistakes people make is confusing weight and mass. Weight is a force, mass is an inertia- do not forget that. Once you have decided on a ride frequency and want to figure out what spring rate you need units errors will put you far off target. An example is shown below where weight is used in place of mass. Equation for calculating spring rate: Ks = 42fr2msmMR2

    Ks = Spring rate (N/m) msm = Sprung mass (kg) fr = Ride frequency (Hz) MR = Motion ratio (Wheel/Spring travel)

    SI Correct example:
    msm = 200 kg fr = 2 Hz MR = 1.25

    Ks = 42(2 Hz)2(200 kg)(1.25)2 = 49348 N/m = 49.3 N/mm

    SI Incorrect example:
    msm = 1960 N fr = 2 Hz MR = 1.25

    Ks = 42(2 Hz)2(1960 N)(1.25)2 = 483611 N/s2 = Wrong and not useful

    English Correct example:


    msm = 440 lbm fr = 2 Hz MR = 1.25

    Ks = 42(2 Hz)2/386.4*(440 lbm)(1.25)2 = 282 lbf/in

    English Incorrect example:


    msm = 440 lbf fr = 2 Hz MR = 1.25

    Ks = 42(2 Hz)2(440 lbf)(1.25)2 = 108566 lbf/s2 = Wrong and not useful

    As you can see, with incorrect units, the results you get are useless. Be careful to use weight/force when needed and use mass when needed- the two are not interchangeable.

    Roll
    Similar to choosing ride frequencies for bump travel, a roll stiffness must be chosen next. The normalized roll stiffness number is the roll gradient, expressed in degrees of body roll per g of lateral acceleration. A lower roll gradient produces less body roll per degree of body roll, resulting in a stiffer vehicle in roll. Typical values are listed below: 0.2 0.7 deg/g for stiff higher downforce cars 1.0 1.8 deg/g for low downforce sedans

    A stiffer roll gradient will produce a car that is faster responding in transient conditions, but at the expense of mechanical grip over bumps in a corner. Once a roll gradient has been chosen, the roll gradient of the springs should be calculated, the anti-roll bar stiffness is used to increase the roll gradient to the chosen value. The roll gradient is usually not shared equally by the front and rear. At OptimumG, we call the roll gradient distribution the Magic Number (Milliken calls it Total Lateral Load Transfer Distribution). The Magic Number is expressed as the percentage of the roll gradient taken by the front suspension of the car. As a baseline, use 5% higher Magic Number than the static front weight distribution. Roll gradients are degrees of body roll per g of lateral acceleration. Roll rates are Newton-meters of torque per degree of body roll or ARB twist. The following equations do no take into account roll due to the tires. Roll gradient of ride springs:

    r -W x H = Ay KF + KR KF = (tf2)KLFKRF 180(KLF+KRF)

    H = Cg to Roll axis dist (m) W = Vehicle weight (N) r/Ay = Roll gradient from ride springs (deg/g) KF = Front roll rate (Nm/deg roll) tf = Front track width (m) KLF = LF Wheel rate (N/m) KRF = RF Wheel rate (N/m)

    Remember that wheel rate is spring rate/ MR2 ; the effect of the spring at the wheel

    KR = (tr2)KLRKRR 180(KLR+KRR)

    KR = Rear roll rate (Nm/deg roll) tr = Rear track width (m) KLR = LR Wheel rate (N/m) KRR = RR Wheel rate (N/m)

    Total ARB roll rate needed to increase the roll stiffness of the vehicle to the desired roll gradient:

    KA =

    KDESKT(t2/2) 180 [KT(t2/2)/180 KDES]

    KW(t2/2) 180

    KA = Total ARB roll rate needed (Nm/deg roll) KDES = Desired total roll rate (Nm/deg roll) KW = Wheel rate (N/m) KT = Tire rate (N/m) t = Average track width between front and rear (m)

    KDES = WH/(/Ay)
    W = Weight of vehicle (N) H = Vertical distance from roll center axis to Cg (m) /Ay = Desired total roll gradient, chosen earlier (deg/g) Front and Rear Anti-Roll Bar stiffness:

    KFA = KANmagMRFA2/100

    KFA = FARB roll rate (Nm/deg twist) KA = Total roll rate (Nm/deg roll) Nmag = Magic Number (%) MRFA = FARB Motion ratio

    KRA = KA(100-Nmag)MRRA2/100
    KRA = RARB roll rate (Nm/deg twist) KA = Total roll rate (Nm/deg roll) Nmag = Magic Number (%) MRRA = RARB Motion ratio

    Remember, the chassis acts as a torsional spring in roll. It is worth comparing the roll rate of your suspension to the roll rate of your chassis- if the chassis twists as much as the suspension, it could be a larger area of concern than the suspension. With steady state roll angles different front to rear, or different roll frequencies front to rear, chassis torsion will be induced- this should be kept in mind. Try this on an excel spreadsheet and have fun. Email us for comment and questions. Next time we will speak about the 3rd spring and introduce damping.

    You might also like