0% found this document useful (0 votes)
75 views28 pages

Unit 2 Jwfiles

The document discusses an op-amp circuit configuration that can be used as a summing amplifier, scaling amplifier, or averaging amplifier depending on the relationship between the feedback resistor and input resistors. The circuit's function is determined by examining the expression for output voltage, which is obtained from Kirchhoff's current law. Specifically, it notes that if the input resistors are equal, the circuit acts as an averaging amplifier if the feedback resistor is equal to the input resistors, or a summing amplifier if the feedback resistor is three times the input resistors.

Uploaded by

Mani Kantta D
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
75 views28 pages

Unit 2 Jwfiles

The document discusses an op-amp circuit configuration that can be used as a summing amplifier, scaling amplifier, or averaging amplifier depending on the relationship between the feedback resistor and input resistors. The circuit's function is determined by examining the expression for output voltage, which is obtained from Kirchhoff's current law. Specifically, it notes that if the input resistors are equal, the circuit acts as an averaging amplifier if the feedback resistor is equal to the input resistors, or a summing amplifier if the feedback resistor is three times the input resistors.

Uploaded by

Mani Kantta D
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 28

www.jntuworld.

com

Op-amp Applications:

Figure shows the inverting configuration with three inputs Va, Vb, and Vc. Depending on the relationship between the feedback resistor Rf and the input resistors Ra, Rb, and Rc, the circuit can be used as either a summing amplifier, scaling amplifier, or averaging amplifier. The circuits function can be verified by examining the expression for the output voltage V0, which is obtained from Kirchhoffs current equation written at node V2. Referring to Figure

www.jntuworld.com

www.jntuworld.com

If Ra=Rb=Rc=R then

www.jntuworld.com

www.jntuworld.com

If (1+RF/R1)=1; It will be averaging amplifier. If (1+RF/R1)=3; It will be summing amplifier. It is basically scaling amplifier.

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

www.jntuworld.com

You might also like