Your Handy Checklist For Practical Work: The Experiment He Experiment

Uploaded by

azz_93

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

202 views

Your Handy Checklist For Practical Work: The Experiment He Experiment

Uploaded by

azz_93

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 2

Your handy checklist for practical work

The experiment he
1 Taking readings
Repeat all readings and average. Show all readings. If timing, measure the period of at least ve oscillations each time. Try for ten if time allows. Remember, timing uncertainty is 0.1 s with a hand-held stopclock. When taking a set of readings make sure that they cover the whole range of the readings fairly evenly. y On tables and graphs the label is ln ( y/m) or log10 ( y/m) to show the unit of y as metres, Check that you know how to use logs.

6 Checking relationships
When checking, state what should be constant, perform the calculation and then state whether the constant was found and whether the relationship is veried. You may want to refer to the uncertainty. y y proportional to x x should be constant. y proportional to 1 x y proportional to ex y x should be constant. y decreases by same factor if x increases by equal amounts.

2 The table of results

Try to arrange for a single table that shows all readings, even the rst, and their averages; Use the correct units and quantities for each column. Use the same precision (i.e. number of signicant gures) for every reading in a particular column. Choose a sensible number of signicant gures for your readings (usually 2 or 3).

Uncertainties
Graphs can be plotted with each point having error bars on the x-axis and the y-axis to show the expected absolute uncertainties. The worst acceptable line should be drawn as a dotted line or labelled as worst acceptable line; it should be the steepest or shallowest line that goes through the error bars of all the points. If this is not possible because of one point that point may be anomalous. Check it it may be wrong.

3 The graph
Label each axis of the graph with both quantity and unit. Make sure your graph occupies at least 5 7 squares (i.e. half the paper) with your plotted points. Ask yourself whether the origin should be plotted. Do not use an awkward scale, i.e. 1 square = 3, 7, 9 units. Plot points neatly, with no large blobs, or crosses. Circle your points if you plot them as dots. The line you draw should be clear, thin and even.

Causes of uncertainty in simple measurements

Lengths rulers may have battered ends, or the zero may not actually be at the end. To avoid parallax uncertainty, you must view any reading from directly above. The likely uncertainty is 1 mm or perhaps 0.3 mm. Times stopwatches measure to 0.01 s but you cant press them that accurately. The likely uncertainty is 0.1 s. Meters (e.g. ammeter) uncertainty is the smallest scale reading, or any uctuation. Graphs uncertainty in gradient is dierence between gradient of best t line and worst acceptable line. Use similar idea to nd uncertainty in y-intercept.

4 Measuring the slope

Use at least half of the drawn straight line. Show the coordinates that you use for the slope or the values of the sides of the triangle that you use. Give your answer to 1 or 2 signicant gures as appropriate. Dont forget units.

5 The straight-line formula for a graph, y = mx + c

If y 2 = ax 3 then plot y 2 against x 3 and the slope is a. If y = ax n then ln ( y) = n ln (x) + ln (a). Plot log10 ( y) or ln ( y) against log10 (x) or ln (x) and the slope is n. If y = a ekx then ln ( y) = kx + ln (a). Plot ln ( y) against x and the slope is k.
AS and A Level Physics Cambridge University Press

Combining uncertainties
There are absolute uncertainties and percentage uncertainties know the dierence.

Your handy checklist for practical skills Study work

When adding or subtracting quantities, add absolute uncertainties. When multiplying or dividing quantities, add percentage uncertainties to get the percentage uncertainty in the answer.

actual uncertainty in B = 2.56 2.5 = 0.06 100 A so B = 2.56 0.06 A Multiplying:

Worked examples
Suppose two measurements have values A = 2.34 0.02 and B = 6.0 0.1 (Notice that the values are quoted to the number of decimal places justied by the uncertainty. Uncertainties are only themselves usually accurate to no better than 1 signicant g so giving more than 2 signicant gures is meaningless.) What are the uncertainties in A + B, B A, B A and B A? Adding and subtracting: A + B = 8.34 0.12 = 8.3 0.1 B A = 3.64 0.12 = 3.6 0.1 Dividing: B = 2.56 A % uncertainty in B = % uncertainty in A A + % uncertainty in B = 1 + 1.5 = 2.5%

B A = 14.04 As when dividing, the percentage uncertainty in B A is again 2.5%. This gives: actual uncertainty in B A = 14.04 2.5 = 0.4 100 B A = 14.0 0.4

Describing and improving an experiment

State every reading you will take. Do not say, Take the readings as before. Make clear what is kept constant and what is changed. Give sensible values for quantities, particularly those that are changed. Use your common sense. Have at least ve sets of readings as a variable changes. Say that you will repeat and average each reading. Say what the axes will be for a straight-line graph. Never just say, plot a graph. Set out your account clearly and logically; use any suggested format if you think it helps. Plan your account briey before you start writing.

AS and A Level Physics Cambridge University Press