EtherChannel in Computer Network
Last Updated :
17 Mar, 2023
EtherChannel is a port link aggregation technology in which multiple physical port links are grouped into one logical link. It is used to provide high-speed links and redundancy. A maximum of 8 links can be aggregated to form a single logical link.
EtherChannel, also known as Link Aggregation Control Protocol (LACP), is a technique used in computer networks to combine multiple physical links between two network switches into a single logical link. This logical link provides increased bandwidth and redundancy, as well as improved load balancing.
EtherChannel works by grouping two or more physical links between switches into a single logical link. This logical link is treated as a single entity, with the switches treating it as a single link. Traffic is distributed across the physical links in the logical link, providing increased bandwidth and improved load balancing.
Need of EtherChannel -
Here is a topology in which two switches are connected with one PC each. The link between the switches and PC is 1000mb/s and the link between the switches is 100mb/s.
Now, suppose if you want to send traffic of more than 100mb/s then we have congestion as the link between the switches is of 100mb/s only and packets will start dropping. Now, to solve this problem, we should have a high-speed link between the switches. To achieve this, We can simply replace the current link with a high-speed link or we can bundle up more than one link of the same speed of 100mb/s. By forming an EtherChannel, you can bundle up more than one link into a single logical link.
But, as you connect the switches with more than one link, STP (Spanning Tree Protocol) will block the least redundant link. As we have made an EtherChannel, all the links (that are grouped as one logical link k) will be treated as single logical links therefore no link will be blocked and also, it will provide us high-speed link and redundancy in our network.
Criteria - To form an EtherChannel, all ports should have:
- Same duplex
- Same speed
- Same VLAN configuration (i.e., native VLAN and allowed VLAN should be same)
- Switch port modes should be the same (access or trunk mode)
EtherChannel protocols - To form an EtherChannel, there are 2 protocols, port aggregation Protocol (PAgP) and link aggregation control protocol (LACP).
1. Port Aggregation Protocol (PAgP) -
The Cisco proprietary protocol Port Aggregation Protocol (PAgP) is an EtherChannel technology. It's a type of data/traffic load balancing that involves the logical aggregation of Cisco Ethernet switch ports. A PAgP EtherChannel can merge up to eight physical links into one virtual link. LACP, or Link Aggregation Control Protocol, is an IEEE open standard. These are namely:
- ON: In this mode, the interface will be a part of EtherChannel but no negotiation takes place.
- Desirable: In this mode, the interface will continuously attempt to convert the other side interface into an EtherChannel.
- Auto: In this mode, the interface will become a part of EtherChannel if and only if it is requested by the opposite interface.
- Off: No EtherChannel configured on the interface.
Configuration -
There is a small topology in which 2 switches S1 and S2 are connected with each other and we have to bundle these two links into a single logical link.
S1(config)# interface fa0/1
S1(config-if)# channel-group 1 mode desirable
S1(config)# interface fa0/2
S1(config-if)# channel-group 1 mode desirable
S1(config)# interface port-channel 1
S1(config-if)# switchport trunk encapsulation dot1q
S1(config-if)# switchport mode trunk
Here, the user has used the mode desirable and switch-port mode trunk. The modes should be the same on both switches therefore the user will configure this on the other switch also.
Now, configuring on switch S2:
S2(config)# interface fa0/1
S2(config-if)# channel-group 1 mode desirable
S2(config)# interface fa0/2
S2(config-if)# channel-group 1 mode desirable
S2(config)# interface port-channel 1
S2(config-if)# switchport trunk encapsulation dot1q
S2(config-if)# switchport mode trunk
2. Link Aggregation Control Protocol (LACP) -
Link Aggregation Control Protocol is an IEEE protocol, originally defined in 802.3ad, used to form an EtherChannel. This protocol is almost similar to Cisco PAgP. There are different modes in which you can configure your interface. These are namely:
- ON: In this mode, the interface will be a part of EtherChannel but no negotiation takes place
- Active: In this mode, the interface will continuously attempt to convert the other side interface into an EtherChannel.
- Passive: In this mode, the interface will become a part of EtherChannel if and only if it is requested by the opposite interface.
- Off: No EtherChannel configured on the interface.
Configuration -
Taking the same topology, you will now configure LACP on both switches. First, configuring for S1:
S1(config)# interface fa0/1
S1(config-if)# channel-group mode active
S1(config)# interface fa0/2
S1(config-if)# channel-group mode active
S1(config)# interface port-channel 1
S1(config-if)# switchport trunk encapsulation dot1q
S1(config-if)# switchport mode trunk
Now, configuring for S2:
S2(config)# interface fa0/1
S2(config-if)# channel-group mode active
S2(config)# interface fa0/2
S2(config-if)# channel-group mode active
S2(config)# interface port-channel 1
S2(config-if)# switchport trunk encapsulation dot1q
S2(config-if)# switchport mode trunk
EtherChannel has several advantages, including:
Increased bandwidth: By combining multiple physical links into a single logical link, EtherChannel provides increased bandwidth between switches. This can help improve network performance and reduce bottlenecks.
Improved redundancy: EtherChannel provides improved redundancy by allowing traffic to be routed over multiple physical links. If one link fails, traffic is automatically routed over the remaining links.
Load balancing: EtherChannel distributes traffic across multiple physical links, providing improved load balancing and preventing congestion on any one link.
Simplified network configuration: EtherChannel simplifies network configuration by treating multiple physical links as a single logical link. This can reduce the complexity of network configurations and make troubleshooting easier.
Cost-effective: EtherChannel can be a cost-effective way to increase bandwidth and redundancy in a network, as it allows existing physical links to be used rather than requiring new hardware.
Similar Reads
Computer Network Tutorial A Computer Network is a system where two or more devices are linked together to share data, resources and information. These networks can range from simple setups, like connecting two devices in your home, to massive global systems, like the Internet. Below are some uses of computer networksSharing
6 min read
Computer Network Basics
Basics of Computer NetworkingA computer network is a collection of interconnected devices that share resources and information. These devices can include computers, servers, printers, and other hardware. Networks allow for the efficient exchange of data, enabling various applications such as email, file sharing, and internet br
10 min read
Types of Computer NetworksA computer network is a system that connects many independent computers to share information (data) and resources. The integration of computers and other different devices allows users to communicate more easily. It is a collection of two or more computer systems that are linked together. A network
7 min read
Introduction to InternetComputers and their structures are tough to approach, and it is made even extra tough when you want to recognize phrases associated with the difficulty this is already utilized in regular English, Network, and the net will appear to be absolutely wonderful from one some other, however, they may seem
10 min read
Types of Network TopologyNetwork topology refers to the arrangement of different elements like nodes, links, or devices in a computer network. Common types of network topology include bus, star, ring, mesh, and tree topologies, each with its advantages and disadvantages. In this article, we will discuss different types of n
11 min read
Network DevicesNetwork devices are physical devices that allow hardware on a computer network to communicate and interact with each other. Network devices like hubs, repeaters, bridges, switches, routers, gateways, and brouter help manage and direct data flow in a network. They ensure efficient communication betwe
9 min read
What is OSI Model? - Layers of OSI ModelThe OSI (Open Systems Interconnection) Model is a set of rules that explains how different computer systems communicate over a network. OSI Model was developed by the International Organization for Standardization (ISO). The OSI Model consists of 7 layers and each layer has specific functions and re
13 min read
TCP/IP ModelThe TCP/IP model is a framework that is used to model the communication in a network. It is mainly a collection of network protocols and organization of these protocols in different layers for modeling the network.It has four layers, Application, Transport, Network/Internet and Network Access.While
7 min read
Difference Between OSI Model and TCP/IP ModelData communication is a process or act in which we can send or receive data. Understanding the fundamental structures of networking is crucial for anyone working with computer systems and communication. For data communication two models are available, the OSI (Open Systems Interconnection) Model, an
4 min read
Physical Layer
Physical Layer in OSI ModelThe physical Layer is the bottom-most layer in the Open System Interconnection (OSI) Model which is a physical and electrical representation of the system. It consists of various network components such as power plugs, connectors, receivers, cable types, etc. The physical layer sends data bits from
4 min read
Types of Network TopologyNetwork topology refers to the arrangement of different elements like nodes, links, or devices in a computer network. Common types of network topology include bus, star, ring, mesh, and tree topologies, each with its advantages and disadvantages. In this article, we will discuss different types of n
11 min read
Transmission Modes in Computer Networks (Simplex, Half-Duplex and Full-Duplex)Transmission modes also known as communication modes, are methods of transferring data between devices on buses and networks designed to facilitate communication. They are classified into three types: Simplex Mode, Half-Duplex Mode, and Full-Duplex Mode. In this article, we will discuss Transmission
6 min read
Types of Transmission MediaTransmission media is the physical medium through which data is transmitted from one device to another within a network. These media can be wired or wireless. The choice of medium depends on factors like distance, speed, and interference. In this article, we will discuss the transmission media. In t
9 min read
Data Link Layer
Data Link Layer in OSI ModelThe data link layer is the second layer from the bottom in the OSI (Open System Interconnection) network architecture model. Responsible for the node-to-node delivery of data within the same local network. Major role is to ensure error-free transmission of information. Also responsible for encoding,
4 min read
What is Switching?Switching is the process of transferring data packets from one device to another in a network, or from one network to another, using specific devices called switches. A computer user experiences switching all the time for example, accessing the Internet from your computer device, whenever a user req
5 min read
Virtual LAN (VLAN)Virtual LAN (VLAN) is a concept in which we can divide the devices logically on layer 2 (data link layer). Generally, layer 3 devices divide the broadcast domain but the broadcast domain can be divided by switches using the concept of VLAN. A broadcast domain is a network segment in which if a devic
7 min read
Framing in Data Link LayerFrames are the units of digital transmission, particularly in computer networks and telecommunications. Frames are comparable to the packets of energy called photons in the case of light energy. Frame is continuously used in Time Division Multiplexing process. Framing is a point-to-point connection
6 min read
Error Control in Data Link LayerData-link layer uses the techniques of error control simply to ensure and confirm that all the data frames or packets, i.e. bit streams of data, are transmitted or transferred from sender to receiver with certain accuracy. Using or providing error control at this data link layer is an optimization,
4 min read
Flow Control in Data Link LayerFlow control is design issue at Data Link Layer. It is a technique that generally observes the proper flow of data from sender to receiver. It is very essential because it is possible for sender to transmit data or information at very fast rate and hence receiver can receive this information and pro
4 min read
Piggybacking in Computer NetworksPiggybacking is the technique of delaying outgoing acknowledgment temporarily and attaching it to the next data packet. When a data frame arrives, the receiver waits and does not send the control frame (acknowledgment) back immediately. The receiver waits until its network layer moves to the next da
5 min read
Network Layer
Network Layer in OSI ModelThe Network Layer is the 5th Layer from the top and the 3rd layer from the Bottom of the OSI Model. It is one of the most important layers which plays a key role in data transmission. The main job of this layer is to maintain the quality of the data and pass and transmit it from its source to its de
5 min read
Introduction of Classful IP AddressingClassful IP addressing is an obsolete method for allocating IP addresses and dividing the available IP address space across networks. It was used from 1981 to 1993 until the introduction of CIDR (Based on Prefixes rather than classes). Classful method categorizes IP addresses into five classes (A, B
10 min read
Classless Addressing in IP AddressingThe Network address identifies a network on the internet. Using this, we can find a range of addresses in the network and total possible number of hosts in the network. Mask is a 32-bit binary number that gives the network address in the address block when AND operation is bitwise applied on the mas
7 min read
What is an IP Address?Imagine every device on the internet as a house. For you to send a letter to a friend living in one of these houses, you need their home address. In the digital world, this home address is what we call an IP (Internet Protocol) Address. It's a unique string of numbers separated by periods (IPv4) or
14 min read
IPv4 Datagram HeaderIP stands for Internet Protocol and v4 stands for Version Four (IPv4). IPv4 was the primary version brought into action for production within the ARPANET in 1983. IP version four addresses are 32-bit integers which will be expressed in decimal notation. In this article, we will discuss about IPv4 da
4 min read
Difference Between IPv4 and IPv6IPv4 and IPv6 are two versions of the system that gives devices a unique address on the internet, known as the Internet Protocol (IP). IP is like a set of rules that helps devices send and receive data online. Since the internet is made up of billions of connected devices, each one needs its own spe
7 min read
Difference between Private and Public IP addressesIP Address or Internet Protocol Address is a type of address that is required to communicate one computer with another computer for exchanging information, file, webpage, etc. Public and Private IP address are two important parts of device identity. In this article, we will see the differences betwe
6 min read
Introduction To SubnettingSubnetting is the process of dividing a large network into smaller networks called "subnets." Subnets provide each group of devices with their own space to communicate, which ultimately helps the network to work easily. This also boosts security and makes it easier to manage the network, as each sub
8 min read
What is Routing?The process of choosing a path across one or more networks is known as Network Routing. Nowadays, individuals are more connected on the internet and hence, the need to use Routing Communication is essential.Routing chooses the routes along which Internet Protocol (IP) packets get from their source t
10 min read
Network Layer ProtocolsNetwork Layer is responsible for the transmission of data or communication from one host to another host connected in a network. Rather than describing how data is transferred, it implements the technique for efficient transmission. In order to provide efficient communication protocols are used at t
9 min read
Transport Layer
Session Layer & Presentation Layer
Session Layer in OSI modelThe Session Layer is the 5th layer in the Open System Interconnection (OSI) model which plays an important role in controlling the dialogues (connections) between computers. This layer is responsible for setting up, coordinating, and terminating conversations, exchanges, and dialogues between the ap
6 min read
Presentation Layer in OSI modelPresentation Layer is the 6th layer in the Open System Interconnection (OSI) model. This layer is also known as Translation layer, as this layer serves as a data translator for the network. The data which this layer receives from the Application Layer is extracted and manipulated here as per the req
4 min read
Secure Socket Layer (SSL)SSL or Secure Sockets Layer, is an Internet security protocol that encrypts data to keep it safe. It was created by Netscape in 1995 to ensure privacy, authentication, and data integrity in online communications. SSL is the older version of what we now call TLS (Transport Layer Security).Websites us
10 min read
PPTP Full Form - Point-to-Point Tunneling ProtocolPPTP Stands for Point-to-Point Tunneling Protocol is a widely used networking protocol designed to create a secure private connection over a public network like the internet. It is Developed by Microsoft and other tech companies in the 1990s It is one of the first protocols used for Virtual Private
5 min read
Multipurpose Internet Mail Extension (MIME) ProtocolMIME (Multipurpose Internet Mail Extensions) is a standard used to extend the format of email messages, allowing them to include more than just text. It enables the transmission of multimedia content such as images, audio, video, and attachments, within email messages, as well as other types of cont
4 min read
Application Layer
Application Layer in OSI ModelThe Application Layer of OSI (Open System Interconnection) model, is the top layer in this model and takes care of network communication. The application layer provides the functionality to send and receive data from users. It acts as the interface between the user and the application. The applicati
5 min read
Client-Server ModelThe Client-Server Model is a distributed architecture where clients request services and servers provide them. Clients send requests to servers, which process them and return the results. Clients don’t share resources among themselves but depend on the server. Common examples include email systems a
5 min read
World Wide Web (WWW)The World Wide Web (WWW), often called the Web, is a system of interconnected webpages and information that you can access using the Internet. It was created to help people share and find information easily, using links that connect different pages together. The Web allows us to browse websites, wat
6 min read
Introduction to Electronic MailIntroduction:Electronic mail, commonly known as email, is a method of exchanging messages over the internet. Here are the basics of email:An email address: This is a unique identifier for each user, typically in the format of [email protected] email client: This is a software program used to send,
4 min read
What is a Content Distribution Network and how does it work?Over the last few years, there has been a huge increase in the number of Internet users. YouTube alone has 2 Billion users worldwide, while Netflix has over 160 million users. Streaming content to such a wide demographic of users is no easy task. One can think that a straightforward approach to this
4 min read
Protocols in Application LayerThe Application Layer is the topmost layer in the Open System Interconnection (OSI) model. This layer provides several ways for manipulating the data which enables any type of user to access the network with ease. The Application Layer interface directly interacts with the application and provides c
7 min read
Advanced Topics
What is Network Security?Network security is defined as the activity created to protect the integrity of your network and data. Network security is the practice of protecting a computer network from unauthorized access, misuse, or attacks. It involves using tools, technologies, policies and procedures to ensure the confiden
9 min read
Computer Network | Quality of Service and MultimediaQuality of Service (QoS) is an important concept, particularly when working with multimedia applications. Multimedia applications, such as video conferencing, streaming services, and VoIP (Voice over IP), require certain bandwidth, latency, jitter, and packet loss parameters. QoS methods help ensure
7 min read
Authentication in Computer NetworkPrerequisite - Authentication and Authorization Authentication is the process of verifying the identity of a user or information. User authentication is the process of verifying the identity of a user when that user logs in to a computer system. There are different types of authentication systems wh
4 min read
Encryption, Its Algorithms And Its FutureEncryption plays a vital role in today’s digital world, serving a major role in modern cyber security. It involves converting plain text into cipher text, ensuring that sensitive information remains secure from unauthorized access. By making data unreadable to unauthorized parties, encryption helps
10 min read
Introduction of Firewall in Computer NetworkA firewall is a network security device either hardware or software-based which monitors all incoming and outgoing traffic and based on a defined set of security rules it accepts, rejects, or drops that specific traffic. It acts like a security guard that helps keep your digital world safe from unwa
6 min read
MAC Filtering in Computer NetworkThere are two kinds of network Adapters. A wired adapter allows us to set up a connection to a modem or router via Ethernet in a computer whereas a wireless adapter identifies and connects to remote hot spots. Each adapter has a distinct label known as a MAC address which recognizes and authenticate
10 min read
Wi-Fi Standards ExplainedWi-Fi stands for Wireless Fidelity, and it is developed by an organization called IEEE (Institute of Electrical and Electronics Engineers) they set standards for the Wi-Fi system. Each Wi-Fi network standard has two parameters : Speed - This is the data transfer rate of the network measured in Mbps
4 min read
What is Bluetooth?Bluetooth is used for short-range wireless voice and data communication. It is a Wireless Personal Area Network (WPAN) technology and is used for data communications over smaller distances. This generation changed into being invented via Ericson in 1994. It operates within the unlicensed, business,
6 min read
Generations of wireless communicationWe have made very huge improvements in wireless communication and have expanded the capabilities of our wireless communication system. We all have seen various generations in our life. Let's discuss them one by one. 0th Generation: Pre-cell phone mobile telephony technology, such as radio telephones
2 min read
Cloud NetworkingCloud Networking is a service or science in which a company’s networking procedure is hosted on a public or private cloud. Cloud Computing is source management in which more than one computing resources share an identical platform and customers are additionally enabled to get entry to these resource
11 min read
Practice
Top 50 Plus Networking Interview Questions and Answers for 2024Networking is defined as connected devices that may exchange data or information and share resources. A computer network connects computers to exchange data via a communication media. Computer networking is the most often asked question at leading organizations such Cisco, Accenture, Uber, Airbnb, G
15+ min read
Top 50 TCP/IP Interview Questions and Answers 2025Understanding TCP/IP is essential for anyone working in IT or networking. It's a fundamental part of how the internet and most networks operate. Whether you're just starting or you're looking to move up in your career, knowing TCP/IP inside and out can really give you an edge.In this interview prepa
15+ min read
Top 50 IP Addressing Interview Questions and AnswersIn today’s digital age, every device connected to the internet relies on a unique identifier called an IP Address. If you’re aiming for a career in IT or networking, mastering the concept of IP addresses is crucial. In this engaging blog post, we’ll explore the most commonly asked IP address intervi
15+ min read
Last Minute Notes for Computer NetworksComputer Networks is an important subject in the GATE Computer Science syllabus. It encompasses fundamental concepts like Network Models, Routing Algorithms, Congestion Control, TCP/IP Protocol Suite, and Network Security. These topics are essential for understanding how data is transmitted, managed
14 min read
Computer Network - Cheat SheetA computer network is an interconnected computing device that can exchange data and share resources. These connected devices use a set of rules called communication protocols to transfer information over physical or wireless technology. Modern networks offer more than just connectivity. Enterprises
15+ min read