GM 6L80 Transmissions: How to Rebuild & Modify

CHAPTER 1

GM 6L80 TRANSMISSIONS

The 6L family of transmissions was introduced by General Motors in multiple applications starting with the 6L80 for the 2006 model year. As with many other GM transmission applications, the 6L units are also sold to other manufacturers for use in their vehicles.

The 6L transmissions are fully automatic 6-speed applications. The 6L applications utilize five multiple-disc clutch packs, one sprag-type one-way clutch, three planetary gearsets, one vane-style oil pump, one EC3-design torque converter, and multiple shafts.

A transmission electrical hydraulic control module (TEHCM) along with a Lepelletier and dual-pinion planetary gearsets make the 6L series unique.

TEHCM

The internal transmission control module (TCM) is more commonly known as a transmission electrical hydraulic control module (TEHCM). The TEHCM incorporates the hydraulic solenoids, temperature sensor, pressure switches, and the transmission computer (TCM) into one assembly. The TEHCM is mounted inside the transmission pan area and is attached directly to the transmission valve body. This means that all of the decisions and the control of the transmission are accomplished internally within the transmission.

The TEHCM communicates with the vehicle sensors and other control modules over a series of controller area network (CAN) data network circuits. Information is transmitted to and from the TEHCM and the other modules via CAN data, which means you need a scan tool that is capable of interpreting CAN data to communicate with the transmission. The TEHCM is programmable. Many 6L issues are not related to internal issues with the transmission; in many cases, they can be repaired by installing updated GM software.

Gearsets

The 6L units use two types of gearsets: Lepelletier and dual pinion designs. This allows the transmission to provide the available ratios without needing additional planetary gearsets.

The transmissions were developed as replacements for their 4- and 5-speed cousins to help meet everchanging fuel-economy and emissions standards. Four different 6L configurations were released: the 6L45, 6L50, 6L80, and 6L90. The primary difference among the configurations is the physical size of the components. This makes most of the parts noninterchangeable among the different model configurations.

In addition, there are multiple part differences even within a specific transmission configuration, so it is imperative that you are sure the parts you are installing are the correct part numbers, as many updates have been implemented on all applications.

Transmission Identification

When compared with today’s units, GM’s numbering system for transmissions was significantly different in the past.

On the THM 400, THM 200, THM 200C, THM 350, THM 350C, THM 325, THM 125, THM 125C, and THM 425 applications, the THM stood for Turbo Hydra-matic, whereas the 400, 200, 350, etc. indicated the torque rating. Those with a C designation utilized a torque converter clutch system to provide a direct connection between the transmission and the engine during operation. Hydra-matic and Allison were the GM divisions that provided the transmission engineering and manufacturing for GM.

1980s

In the early 1980s, the numbering system changed to make it more of a worldwide approach because GM was one of the world’s most dominant manufacturers and was selling engines and transmissions to various other automotive manufacturers.

Transmissions such as the THM 700-R4, 200-4R, 440-T4, and 325-4L were introduced. The 700 and 200 referenced the torque rating in Newton meters (Nm), while the R indicated that it was a rear-wheel-drive application. The 4 designation indicated the number of forward speeds that are available.

Changes

In the late 1980s and early 1990s, the designations began to change again. The THM 700-R4 became the 4L60, the THM 400 became the 3L80, and the 440-T4 became the 4T60. In this case, the 4 indicated that it was a 4-speed unit. The L indicated that it was a longitudinally mounted application (rear-wheel drive); a T would indicate it was a transverse-mounted application (front-wheel drive). The 60 or 80 designations indicated the unit’s relative torque capacity. This may seem confusing, but it simply means that a transmission with an 80 has a higher torque capacity when compared to a 60 application within the same vehicle type. Since the number is relative, you cannot compare capacities from one unit to another, such as a 4T60 to a 4L60, because they are not the same torque rating; one is a front-wheel-drive, while the other is a rear-wheel-drive application. The updated designations were an attempt to provide a consistent numbering system across the world for all manufacturers using Hydra-matic units.

1991

In 1991, the numbering system evolved again with the addition of fully electronic control systems for many transmission applications. Prior to this point, the only electronics used on the transmission were used to control the torque converter clutch (TCC).

In 1991, the THM 400/3L80 received a complete redesign as a 4-speed unit known as the 4L80E, and in 1993, the 4L60 became the 4L60E. In addition, new front-wheel-drive applications were also introduced and updated, including the 4T60 transitioned to the 4T60E in 1991 and the 425/325-4L was replaced with the 4T80E in 1993.

GM 6L45/6L50/6L80/6L90 North American Usage

Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL, Escalade, (C/K trucks (C = 2WD, K = 4WD)

Camaro (F-car)

Corvette, XLR (Y-car)

Express, Savana (G/H vans, G = 2WD, H = AWD)

SRX (E-car)

STS (D-car)

CTS (D-car)

3500/4500 Medium-Duty Truck

Colorado, Canyon (S/T Trucks S = 2WD, T = 4WD)

Car/truck model/body designations refer to the fourth or fifth digit of the VIN code. The fourth digit is used on cars and the fifth digit is used on trucks for the body type designation.

Not all years for the vehicles listed utilize only the 6L series transmissions, as other transmission models may also be used.

The E designation was introduced because GM still had mechanically controlled units in production, and it wanted to eliminate the confusion between a mechanically controlled unit and an electronically controlled unit. All E applications utilized fully computer-controlled shifts, and most were equipped with electronically controlled line pressure. In addition, adaptive-shift software was also introduced on some models. Adaptive strategies allow the TCM to control shift feel and to adjust for clutch and seal wear within the transmission.

2006 and Later

Models from 2006 and later years have seen major introductions of GM 6-, 8-, 9-, and 10-speed applications for both rear-wheel-drive and front-wheel-drive vehicles. Again, the designations changed. The E designation is no longer used by GM, as all of the 6-, 8-, 9-, or 10-speed applications utilize fully integrated electronic control systems. The updated transmission designs are now utilized by GM and are sold to other manufacturers as well.

Current GM, non-hybrid transmission applications include the 6L45, 6L50, 6L80, 6L90, 6T30, 6T35, 6T40, 6T45, 6T50, 6T70, 6T75, 6T80, 8L45, 8L90, 9T45, 9T50, 9T60, 9T65, 10L60, 10L80, 10L90, and 10L1000.

As with all GM transmissions, the identification numbers/letters associated with the 6L80 have specific meanings regarding the transmission construction.

For example, for the 6L80:

RPO Identification

GM has always used a process known as regular production option (RPO) codes to identify the component content for its vehicles. When a dealer orders a vehicle, every option on that vehicle, including the engine, transmission, axle ratio, radio, braking system, suspension system, A/C system, etc., is given a three-digit alpha-numeric designation. Those three-digit designations (RPOs) are used by the assembly plant to ensure the vehicle is built with the options that the dealer ordered.

For example, take a Chevrolet or GMC truck with a Z71 decal on the truck bed. The RPO code for an off-road suspension package is Z71.

All RPO codes are three digits. Engine RPOs typically begin with the letter L (LT1, LT4, L88). Rear-wheel-drive axle options typically begin with the letter G (GT4, G80). Transmission RPO codes begin with the letter M (MT1, M30). The RPO codes are contained on a label known as a service parts identification (SPID) label. The codes are positioned in alpha-numeric order on the label. The SPID label is typically located in one of four locations depending on the year and vehicle model: the glove box, center console, rear decklid (trunk), or on the spare tire cover.

The RPO codes are listed on the RPO tag that is typically located in the glove box, center console, spare tire cover, or trunk lid for 2018-and-earlier applications. The RPO code is a three-digit designation that represents the equipment content on vehicle. Transmission RPOs start with the letter M, engine RPOs start with the letter L and rear-wheel-drive final-drive information starts with the letter G The RPO is often required for parts ordering and to access the correct service information.

2018 and later

Until the 2018 model year, the RPO/SPID label was located in a position that was mentioned. However, beginning with the 2018 model year, GM began to transition the label information to a different location and format. As new bodystyles and vehicle redesigns were introduced, the location of the RPO information changed. The new label requires a smartphone with a quick response (QR) reader application to access the three-digit codes. The label is now located on the driver-side B-pillar. Open your driver-side door and look at the area below the body striker. Most smartphone applications are available for free and work very well. Available applications include Data Matrix, I-Nigma, QR Scanner, QR Droid, Bar Code, and NeoReader.

The RPO tag location and design began to change beginning in the 2018 model year. The new design tag requires a smartphone and a QR reader application to access the vehicle’s RPO information. With the smartphone application open, scan the QR label. The application will then display the RPO content on your phone.

To read the new design label, open the smartphone application and position the sight box for the application over the QR label area. The application will read the label and display the RPO codes as well as the vehicle identification number (VIN) and other pertinent information.

Know the RPO

As you may be wondering, why is it important to know the RPO code for the component/system you are attempting to repair? Many components share similarities, but there can be some differences. This means that the part you are replacing could be different even though it may look identical. In many instances, the parts counterperson will ask for the option content or the vehicle’s VIN so that he or she can determine the option content and make sure that you receive the correct parts for your application. In addition, component repair processes and system wiring vary, so you may need RPO information to select the correct wiring schematics or repair information.

GM Transmission RPO Codes

The following chart lists all of the RPO codes for the various GM Hydra-matic/Allison 4-, 5-, 6-, 8-, 9-, and 10-speed applications for light-duty GM vehicles.

Transmissions, as with other components, use their own unique RPOs. The 6L45 utilizes the RPO MYA, 6L50 MYB, 6L80 MYC, and 6L90 MYD for the 6-speed rear-wheel-drive applications.

Transmission Tag Information

All Hydra-matic transmissions include a tag that helps to identify the transmission. The 6L family of transmissions use a laminated tag that is mounted to a flat on the transmission case. The tag is typically located on the passenger’s side of the case in the rear corner.

As with the RPO tag, the transmission tag contains a tremendous amount of information about the transmission, including the model code and the build/Julian date. Many transmission updates are attached to a specific Julian date, so when ordering parts, you may be required to provide the tag information to the parts person to get the correct parts for your application.

Potential Tag Issue

Take care when cleaning the tag because it is easily damaged. One suggestion is to take a picture of the tag so that you will have the information available for the parts counterperson if needed. ■

The 6L80 tag includes the following information: the model year, model code, transmission family, transmission assembly part number, Julian date, sequential serial number, plant code, broadcast code, bar code, and transmission identification.

Some of the information on the tag is very important when it comes to ordering parts and determining if your transmission was equipped with certain updates. The following information may be required by your parts counterperson.

6L80 Unit Specifications

The unit specifications for the 6L80 transmission are below:

RPO: MYC

Input torque capacity: 430 ft-lbs (583 Nm)

Output torque capacity: 664 ft-lbs (900 Nm)

Gear ratios: first, 4.02:1; second, 2.36:1; third, 1.53:1; fourth, 1.15:1; fifth, 0.85:1; sixth, 0.67:1; reverse, 3.06:1

Maximum shift speed: 6,500 rpm

Maximum GVW: 8,600 pounds

Maximum GCVW: 14,000 pounds

PRNDL positions: P, R, N, D, and S or M

Two shift solenoids used (on/off design), SS1, SS2

Six pulse width modulated (PWM) controlled pressure control solenoids (PCS): PCS, PCS2, PCS3, PCS4, PCS5, and TCC

Bosch 32-bit TEHCM mounted internally to the transmission on the valve body (referred to as the control solenoid valve assembly in the parts information). The TEHCM incorporates the solenoids, oil pressure switches, fluid temperature sensor (TFT), and is bolted to the valve body using six bolts.

EC3 Torque Converter 300-, 245-, 265-, or 258-mm twin plate designs. EC3 stands for controlled capacity converter clutch, which means that the torque converter clutch will not always be fully locked. This means that the converter is designed to slip under certain driving conditions to improve drivability.

Fluid required: Dexron VI

Fluid capacity: 9.5L (10 qts), 9.7L (10.2 qts),11.9 L (12.6 qts) depending on model

Clutch-to-clutch shifts: five clutches (two holding, three driving), one sprag, one-way clutch

Planetary front (Lepelletier) output (dual pinion design)

Vane-style oil pump

Internally mounted TISS (transmission input speed sensor) and TOSS (transmission output speed sensor) are Hall-effect design speed sensors

Internal mode switch (IMS) range sensor equipped

Performance algorithm shifting (PAS) programming (downshift program)

Performance algorithm lift foot (PAL) programming (upshift program)

Sport mode and tap-shift equipped (tap shift allows you to manually shift the unit paddles or buttons)

Adaptive strategies with fast-learn capabilities

Multiple transmission only diagnostic trouble codes (DTCs)

Model Year

The model year may not be the same as the year of the vehicle on which you are working depending on the vehicle’s production date.

Model Code

The model code varies depending on the vehicle platform and the type of vehicle into which the transmission is going.

Julian Date

The Julian date represents the numbered day of the year. January 1 is Julian date 001, while December 31 is Julian date 365. Update changes are tied to the Julian date rather than solely the model year, so when it comes to ordering parts, it may be very important.

Broadcast Code

The broadcast code is used to identify the type of transmission.

Inspection and Service

Basic inspection and service of the 6L80 begins and ends with the fluid and fluid service. For the transmission to operate correctly, maintaining the correct fluid level and fluid condition are critical. Burnt fluid or a unit that was operating low on fluid may indicate a reason for a transmission failure.

Dexron VI is the only approved fluid for 6L applications. Do not use Dexron III or other fluids in this application. Dexron VI made major improvements in oxidation resistance, lubrication capabilities, and temperature ranges when compared to Dexron III. Dexron VI is licensed by several manufacturers.

Fluid

The 6L80 uses Dexron VI fluid. Dexron VI is far superior to Dexron III, which it replaced. Major improvements in wear control, film strength, friction durability, and oxidation stability were achieved. Clutch-to-clutch shift transmissions, such as the 6L/6T series, require a much more robust fluid as compared to previous automatic transmission designs. Companies currently licensed to produce Dexron VI include Mobil, Chevron, Shell, SK Lubricants, and Valvoline.

Fluid Capacity

The 6L80 has five different oil pans available depending on the application. It is imperative that you have the correct oil pan. Either overfilling or underfilling the transmission can result in transmission clutch failure. Two different pan designs are used: those that are equipped with a standpipe (various standpipe heights are used) and those that are equipped with a dipstick (no standpipe is used).

Fluid capacity is strictly dependent on the vehicle application in which the transmission is used, as the pan part number is dependent on the body type. So, when it comes to fluid capacity, it is best if you reference the owner’s manual for the capacity for your application.

Fluid Level

How the fluid level is checked varies depending on whether the pan is equipped with a standpipe or it uses a dipstick.

Dipstick Applications

On units equipped with a dipstick, before checking the fluid level, perform the following:

Start the engine and park the vehicle on a level surface. Chock the wheels.

Apply the parking brake and vehicle brake, and place the shift lever in Park. Move the shifter to each forward gear range as well as Reverse, pausing for 3 seconds in each range. Place the vehicle in Park.

Allow the engine to