Everand Logo

Welcome to Everand!

  • Discover millions of ebooks, audiobooks, and so much more with a free trial

    From $11.99/month after trial. Cancel anytime.

    Carving Figure Caricatures in the Ozark Style
    Carving Figure Caricatures in the Ozark Style
    Carving Figure Caricatures in the Ozark Style
    Ebook147 pages45 minutes

    Carving Figure Caricatures in the Ozark Style

    By Harold R. Enlow

    4/5

    ()

    Read preview

    About this ebook

    Wood carving in the Ozark style is easy and fun when you follow professional carver Harold Enlow's directions. Using figures he has carved for his own collection in Dogpatch, Arkansas, he gives instructions and illustrations that cover every angle of carving figure caricatures.
    He tells you how to go about selecting and preparing the wood, selecting the proper tools, sharpening the tools, using a mallet and band saw, roughing out a figure from a block, carving a head and face, and finishing your carvings. Then he presents explicit instructions for ten projects: a Missouri mule, a mountaineer, a hobo, a cowboy, a hill woman, Rufus and Sadie, Bootsie the cow, a banjo player, "Ozark Trail's End," and "Revenooers." Each project is illustrated in diagram form (front and usually profile) to make it easy to draw on the wood, and there are photographs of each completed project and some in intermediate stages. The general instructions are also illustrated copiously, and there are photographs of other completed carvings from the author's collection — a total of 22 drawings and 47 photographs in all.
    Whether you are an accomplished carver or just beginning, you will find these caricatures a delightful group and very easy to do. The projects are arranged in order of difficulty, and by the time you get to the last one, you will be ready to do your own designs and carve your own caricatures.
    "One of the better (books) around on wood-carving." — Indianapolis News.

    LanguageEnglish
    PublisherDover Publications
    Release dateNov 1, 2012
    ISBN9780486152592
    Carving Figure Caricatures in the Ozark Style

    Related to Carving Figure Caricatures in the Ozark Style

    Related ebooks

    Crafts & Hobbies For You

    View More
    View More

    Related podcast episodes

    Related categories

    Reviews for Carving Figure Caricatures in the Ozark Style

    4/5

    3 ratings1 review

    What did you think?

    Tap to rate

    Review must be at least 10 words

    • 3/5

      Apr 20, 2022

      Good book for carving caricatures! Detailed info on painting, also.

    Book preview

    Carving Figure Caricatures in the Ozark Style - Harold R. Enlow

    22.

    Selecting and Preparing the Wood

    WHICH WOOD TO USE

    Most carvers use woods which are nearby and readily available; a carver is lucky if he has good carving wood in his back yard. Not all carvers are this lucky, however, and many must learn what kind of wood to be on the lookout for.

    In the Ozark country, where I live, basswood or lindenwood (linn to old-timers) is the standby for carving. It is ideal for small carvings of people and animals, especially caricatures. Other woods used, especially for larger projects, are sassafras, black walnut, butternut and red cedar. But I would advise the beginning carver to get linden if he or she possibly can.

    In my area linden is usually purchased from small mountain sawmills, the tree usually having been cut only a few days before being sawed into planks.

    PREPARING WOOD FOR CARVING

    The primary step in preparing wood for carving—whether linden or any other wood—is getting it sufficiently dry. Since most carvers have no kiln in which to dry it, it must be stacked and stripped. Stripping means putting small, inch-thick pieces of wood between the planks so that air will circulate between them.

    If the planks are allowed to dry through the ends instead of the sides and edges, long cracks will appear and ruin a good part of each piece. Ends should therefore be coated with melted paraffin to keep moisture from escaping. Use extreme caution when melting the paraffin; put the wax in a clean coffee can, then allow it to melt in a pan of hot water. Do not melt over a direct flame. Use an old paint brush to apply the melted paraffin to the ends of each plank.

    After coating the ends, store stacked wood in a dry place for several weeks before carving. Drying time depends largely upon the thickness of the wood, but for the small projects in this book, which use 2- to 3-inch planks, drying time is about six weeks. Logs cut in winter months dry faster and work better; sap is down and there is less moisture in them at that time of year.

    Selecting the Proper Tools

    THE BASIS FOR SELECTION

    Many carving tools of good quality are available on today’s market, and the purchaser could well be confused by the sheer variety of them. My own tool box contains several different brands, since I have experimented over the years with various tools, looking for different characteristics. Actually, there are two basic criteria for choosing tools: good design and ability to hold an edge.

    Many beginners fail to realize that most carving tools are sold unsharpened—one hates to think how many carvers have given up after trying unsharpened tools. Sharpening will be discussed in the next chapter—it is probably the most important fact for the beginning carver. Most of the time when a tool doesn’t cut properly, it isn’t because of the tool itself but because of improper sharpening.

    TOOL HANDLES

    A good tool always has a shoulder where it enters the handle to keep it from splitting the handle wood. Tool handles should be of very hard wood, and the larger tools should have a ferrule or metal banding where the handle attaches to the tool. Handles for extra-heavy work should be banded at both ends.

    Most small and medium tools are sold with handles attached; large tools and their handles, however, usually are sold separately. You will have to know how to attach the handle if you purchase them separately. Many tools have been broken because the handle was forced on. Tool handles have a pre-drilled hole, ready to accept the tool. Twist the tang of the tool into the handle, using a back-and-forth motion, so that the tool drills its way in. Continue until the tool is about ¼ inch from being seated. Then place it on a block of wood and drive the final quarter-inch with a wooden mallet.

    Since a bent tool is easily broken, do not drive the handle in on a block of wood. When it is twisted in, place the shank of the tool in a vise between two blocks of wood, then pound on the handle.

    SUBSTITUTION AND NUMBER OF TOOLS

    While, as we said, many tools are available

    Enjoying the preview?
    Page 1 of 1