Insteon (commonly written INSTEON) is a system for connecting lighting switches and loads without extra wiring.[1] INSTEON is a dual-band mesh home area networking topology employing AC-power lines and a radio-frequency (RF) protocol to communicate with devices.[2] It is a home automation networking technology designed by SmartLabs, Inc.[1] INSTEON is designed to enable devices, such as light switches, thermostats, motion sensors, etc. to be networked together using the power line, radio frequency (RF), or both. All INSTEON devices are peers, meaning each device can transmit, receive, and repeat any message of the INSTEON protocol, without requiring a master controller or routing software.[3]
All INSTEON compatible devices act as repeaters, meaning that they repeat each message they hear. This is in contrast to other mesh networking topologies where only "advanced nodes" repeat. Automatic error detection and correction are included in all INSTEON compatible products. The power line protocol uses phase-shift keying and is designed so that the repetition is synchronized: All repeaters repeat the same message during precisely-defined time slots, so while the repetitions collide, they do so in harmony in a manner that preserves the message. The power line AC frequency is used as the synchronization source.
Contents |
Network topology [link]
INSTEON is an integrated dual-mesh network that combines wireless radio frequency (RF) with the home's existing electrical wiring. This is intended to improve reliability by providing a backup system in case of wireless interference. As a peer-to-peer network, devices do not require network supervision, thus dispensing with the need for controllers and routing tables.
Each transmission contains a two-bit "hops" field that starts at 3 and is decremented each time a node in the network repeats a message. The repetition scheme is designed so that all of the nodes repeat the messages in precise synchrony with one another, so the repetitions collide by design and strengthen one another in harmony.
Installation [link]
INSTEON devices are set up using a Plug and Tap method. Each device has its own unique ID. The procedure to link two INSTEON devices can be done manually at the devices. Although a basic system can be deployed without a controller or PC, such a device may be added for advanced home management. Some devices are able to save and restore the configuration of individual devices on the network.
Transmission [link]
INSTEON uses digital signal processing to encode and transmit messages, enabling rapid transmission of control data between INSTEON devices. Individual INSTEON messages can also carry up to 14 bytes of arbitrary user data to support home-control applications from developers.
X10 compatibility [link]
INSTEON products on the power line can be manufactured to be X10-compatible. Homeowners with existing X10 networks can migrate to an INSTEON network without having to discard all their existing X10 devices. INSTEON devices repeat INSTEON signals, but not X10 signals.
Although both can be sent over the same power line, INSTEON commands are not similar to or compatible with X10, and X10 commands are not INSTEON. Rather, INSTEON driver chip sets simply include the capability of transmitting, receiving, and responding to X10 power line messages in addition to INSTEON messages. X10 compatibility is implemented in the INSTEON-compatible chip sets made by SmartLabs, which are offered for sale to other product vendors wishing to implement INSTEON in their products.
Specifications [link]
- Data rate
- Instantaneous (within a single packet): 13,165 bit/s
- Sustained best case (over multiple packets): 2,880 bit/s
- Sustained average case: 180 bit/s .[4]
- Message types
- Standard: 10 bytes
- Extended: 24 bytes
- Message format/structure
- Source Address: 3 bytes
- Destination Address: 3 bytes
- Flags: 1 byte
- Command: 2 bytes
- User Data: 14 bytes
- Message Integrity: 1 byte
- Devices supported
- Unique IDs: 16,777,216
- Device Types: 65,536
- Commands: 65,536
- Group Members: 256
- INSTEON engine memory requirements
- RAM: 80 bytes
- ROM: 3 kilobytes
- Typical application (light switch, lamp dimmer) memory requirements
- RAM: 256 bytes
- EEPROM: 256 bytes
- Flash: 7 kB
- Power line physical layer
- Frequency: 131.65 kHz
- Modulation: Binary phase-shift keying (BPSK)
- Min Transmit Level: 3.16 Vpp into 5 ohms
- Min Receive Level: 10 mV
- Phase Bridging: INSTEON RF or hardware
- RF physical layer
- Frequency: 902 to 924 MHz
- Modulation: FSK
- Sensitivity: -103 dBm
- Range: 150 ft unobstructed line-of-sight[5]
References [link]
- ^ a b "How to Control Your Home with your Cell Phone". Popular Mechanics. October 1, 2009. https://www.popularmechanics.com/home_journal/home_improvement/4301977.html. Retrieved August 19, 2010.
- ^ "Refresh!: INSTEON Technology". Electronic Design. Penton Media, Inc.. April 5, 2006. https://electronicdesign.com/article/boards-modules-systems/refresh-insteon-technology33281.aspx. Retrieved August 19, 2010.
- ^ "What is Insteon?". https://www.Insteon.net/aboutInsteon.html. Retrieved 2007-06-25.
- ^ Irwin et al. (2011). Exploiting Home Automation Protocols For Load Monitoring In Smart Buildings. https://www.cs.williams.edu/~jeannie/papers/insteon-buildsys11.pdf.
- ^ Darbee, Paul (August 11, 2005). "INSTEON The Details" (PDF). Smarthome Technology. https://www.Insteon.net/pdf/Insteondetails.pdf. Retrieved August 19, 2010.
See also [link]
- DASH7, for wireless sensor networking
- Enocean
- HomePlug
- KNX (standard), for intelligent buildings
- ONE-NET, an open source alternative
- Powerline communication
- Universal powerline bus (UPB)
- X10 (industry standard), a home automation protocol
- Z-Wave, an RF mesh technology
- ZigBee
External links [link]
|
|||||||||||||||||||||||||||||||||||||||||
https://wn.com/Insteon
Insteon (company)
Insteon is an Irvine, CA-based developer of home automation (aka domotics) hardware and software. The technology, also called Insteon, allows light switches, lights, thermostats, motion sensors, and other electrical devices to interoperate through power lines, radio frequency (RF) communications, or both. The company produces over 200 products featuring the technology. The company partners with Microsoft,Google,Apple,Amazon,Logitech and others to deliver home automation functionality to customers.
Insteon is a subsidiary of Smartlabs, Inc., also based in Irvine, CA.
History
Insteon was founded in 2012 in Irvine, CA by CEO Joe Dada. Dada had previously founded Smarthome in 1992, a home automation product catalog company, and operator of the Smarthome.com e-commerce site. In the late 1990s, Dada acquired two product engineering firms which undertook extensive product development efforts to create networking technology based on both power-line and RF communications. In 2004, the company filed for patent protection for the resultant technology, called Insteon, and it was released in 2005. In 2012, the company released the first network-controlled light bulb using Insteon-enabled technology, and at that point Dada spun Insteon off from Smarthome.
