Abstract
The axion emerges in extensions of the Standard Model that explain the absence of CP violation in the strong interactions. Simultaneously, it can provide naturally the cold dark matter in our universe. Several searches for axions and axion-like particles (ALPs) have constrained the corresponding parameter space over the last decades but no unambiguous hints of their existence have been found. The axion mass range below 1 meV remains highly attractive and a well motivated region for dark matter axions. In this White Paper we present a description of a new experiment based on the concept of a dielectric haloscope for the direct search of dark matter axions in the mass range of 40 to 400 \(\upmu \hbox {eV}\). This MAgnetized Disk and Mirror Axion eXperiment (MADMAX) will consist of several parallel dielectric disks, which are placed in a strong magnetic field and with adjustable separations. This setting is expected to allow for an observable emission of axion induced electromagnetic waves at a frequency between 10 to 100 GHz corresponding to the axion mass.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Axions are hypothetical low-mass bosons predicted by the Peccei–Quinn (PQ) mechanism, which explains the absence of CP-violating effects in quantum chromodynamics (QCD) [1,2,3,4]. Axions could also provide the cold dark matter (DM) of the universe [5,6,7] and as such are among the few particle candidates that simultaneously resolve two major problems in physics.
Assuming axions make up most of the DM in the universe, their mass \(m_a\) is expected to be less than \(\sim \) meV (cf. [8, 9] and references therein). Mass values higher than \(\sim 20\) meV are excluded due to astrophysical constraints, see [10] for a review and [11,12,13] for updates and descriptions of recent anomalies. The existing experimental efforts for DM axion searches focus on an \(m_a\) range below \(\sim \,40\,\upmu \hbox {eV}\). This is motivated by the realignment mechanism of the axion field providing the right amount of DM in scenarios in which the PQ symmetry is broken before inflation and never restored thereafter. Among these experimental efforts are microwave cavity searches [14] such as ADMX [15, 16], ORGAN [17], HAYSTAC [18,19,20] or CULTASK [21], which have begun to probe part of the axion parameter space.
In scenarios in which the PQ symmetry is broken after inflation, the realignment mechanism now along with decaying topological defects provides a cold DM axion density that matches the observed value if the axion mass \(m_a\) is of the order of \(100\,\upmu \hbox {eV}\) [22,23,24,25,26,27]. One recent attempt to improve the numerical simulations points to a more concrete mass value of \(m_a\sim \,26\,\upmu \hbox {eV}\) [28] but still faces large theoretical uncertainties [29].
We propose to search for QCD axion DM in the mass range around \(100~\upmu \hbox {eV}\), using a dielectric haloscope [30]. This concept makes use of the “dish antenna” idea [31] and of additional signal enhancements possible by having multiple dielectric layers [32]. The proposed MAgnetized Disk and Mirror Axion eXperiment (MADMAX) will consist of a mirror and about 100 dielectric disks each about \(1~\hbox {m}^2\) large with adjustable separations placed inside a homogeneous 10 T strong magnetic dipole field.
This White Paper gives a summary of the principles upon which dielectric haloscopes are based, followed by a description of the first baseline design that could be used for the search of axions with mass in the range of 40 to 400 \(\upmu \hbox {eV}\). The results of measurements at a test setup are presented, which lead us to the conclusion that it should be realistic to build an experiment that can cover a large fraction of the parameter space including the unexplored one predicted for DM axions in the post inflationary PQ symmetry breaking scenario.
2 Theoretical motivation
2.1 Strong CP problem
In the standard model (SM) of particle physics, violation of CP in the strong interactions is controlled by just one parameter, the \(\theta \) angle. This angle appears as the sum of two contributions with a-priori unrelated origins: the angle defining the vacuum of QCD, \(\theta _{\mathrm{QCD}}\), and the common phase of the quark mass matrix, Arg Det \(M_q\), related to the Yukawa couplings of the Higgs sector. Observable effects derive only from this combination. When we redefine quark fields to make their masses real, the phase appears as the coupling constant of the topological charge density operator of QCD, i.e., the SM Lagrangian contains a term
which violates parity, time-reversal and thus CP. In (2.1) \(G_{\mu \nu a}\) denotes the QCD field-strength tensor with \(\widetilde{G}^{\mu \nu }_a \equiv \frac{1}{2} \epsilon ^{\mu \nu \alpha \beta } G_{\alpha \beta a}\) being its dual, color index \(a = 1,\ldots ,8\), and \(\mathbf{E}_a\) and \(\mathbf{B}_a\) the illustrative chromo electric and chromo magnetic fields, respectively. Non-zero values of \(\theta \) imply CP violating observables such as nuclear electric dipole moments but none of these effects have been observed to date. As a key example, the electric dipole of the neutron is predicted to be \(d_n = 2.4 \times 10^{-16} \theta e\) cm [33] but the most recent experiment [34] concluded that \(|d_n|<2.9\times 10^{-26} e\) cm, so \(\theta \) must be extremely tiny, \(\theta < 1.3\times 10^{-10}\). This is an amazingly small upper limit, especially if we consider that the only other CP violating phase in the SM, the CKM angle \(\delta _{13}=1.2\pm 0.08\), is not particularly small and also comes from the quark mass matrix. Indeed, the smallness of CP violation gives us a hint that some dynamical mechanism could be at work to suppress the effects of the \(\theta \) term in Eq. (2.1).
2.2 Axions
In the year 1977 Peccei and Quinn proposed a mechanism to solve the strong CP problem, often considered to be the most elegant to date [1, 2]. The vacuum energy density of QCD depends on \(\theta \), i.e., \(V_{\mathrm{QCD}}=V_{\mathrm{QCD}}(\theta )\), and its absolute minimum liesFootnote 1 at \(\theta =0\) [36], which is CP conserving. If \(\theta \) is interpreted to be a dynamical field, \(V_\mathrm{QCD}(\theta )\) becomes the potential energy of that field so that the expectation value \(\langle \theta \rangle \) will be dynamically driven to zero, explaining the absence of CP violation.
Overview of axion masses \(m_a\) (equivalently \(f_a\)) excluded by a variety of astrophysical and cosmological arguments (blue) or laboratory searches (gray) together with experimental prospects (green) and axion cold DM predictions. Pre- and postinflation PQ breaking scenarios are explained in Sect. 2.4
This mechanism relies on a global U(1)\(_{\mathrm {PQ}}\) symmetry that breaks spontaneously at the PQ scale \(f_a\). A model-independent consequence is that excitations of \(\theta (x)\) around the minimum of the potential represent a new particle, the axion [3, 4]. The dynamical \(\theta (x)\) field needs a kinetic term \(f_a^2 (\partial _\mu \theta )(\partial ^\mu \theta )/2\). The axion field is the canonically normalized version of \(\theta \), \(a(x)=\theta (x) f_a\). Values of \(f_a\lesssim 10^8\) GeV are excluded experimentally and astrophysically, so the axion offers a window to discover physics at ultra-high energies not testable by current accelerator techniques.
The cancellation of \(\langle \theta \rangle \) is dynamical, leading to residual oscillations of \(\theta \) around the minimum, which are expected for generic initial conditions. As the age of the universe is finite, these oscillations are quasi-classical field oscillations that could constitute today’s cold DM referred to at the realignment mechanism [5,6,7].
The axion mass is given by
where the numbers in brackets denote the uncertainty in the last digit, dominated by the uncertainty in the up-down quark mass ratio (first bracket) and higher order effects (second bracket) [37]. The interaction of the axion with electric fields \(\mathbf{E}\) and magnetic fields \(\mathbf{B}\) is given by the Lagrangian density
the fine structure constant \(\alpha \), and the model-dependent ratio of the electromagnetic and colour anomalies \({\mathcal {E}}/{\mathcal {N}}\) of the PQ symmetry. Again the number in brackets refers to the uncertainty in the last digit [37]. These numbers are quoted as recently obtained at NLO in chiral perturbation theory [37]. The topological susceptibility entering in equation (2.2) has also been calculated from first principles exploiting lattice QCD, with a similar uncertainty (see reference [26]). One should however note that \(C_{a\gamma }\) might vary by up to two orders of magnitude in somewhat more exotic axion models [38, 39].
2.3 Landscape and constraints
The constraints on axion models are usually quoted on a specific coupling, e.g., \(C_{a\gamma }\) as a function of \(m_a\). A broad picture is shown in Fig. 1. A combination of stellar evolution and cosmological arguments together with experimental searches rule out axions with \(f_a< 3\times 10^8\) GeV corresponding to \(m_a>20\) meV. A significant part of the axion parameter range is excluded by the impact that axion emission would have in different stellar objects: SN1987A, horizontal branch and red giant stars in globular clusters, white dwarfs and the Sun (see [10] for a summary and [11, 12] for updates). Interestingly, some of the observed systems such as white dwarfs, horizontal branch stars in globular clusters and the tip of the red giant branch of the globular cluster M5 show a slight preference for non-standard energy loss and could be hinting at an axion or ALP with \(f_a\sim 10^9\) GeV [12, 40].
The broad picture of experimental limits on any ALP (and including QCD axions such as the KSVZ axion) coupled to photons is shown in the \(m_a\)–\(g_{a\gamma }\) plane in Fig. 2, where
For a recent review on the constraints and prospects for experimental detection of the axion, including this and other couplings, we refer to [41].
2.4 Axion dark matter
DM axions can be produced in the early universe by at least two processes: in reactions from SM particles in the thermal bath (thermal axions) and by the vacuum realignment mechanism (non-thermal axions) [5,6,7]. The cold, non-thermal, population is the one that can provide the right amount of cold DM. Axion cosmology is reviewed in [8, 9].
In the vacuum realignment mechanism, the axion field starts with certain initial conditions, which then evolves, driven by its potential energy, \(V_{\mathrm{QCD}}\). The axion DM yield is thus determined by initial conditions and not by thermodynamic processes. Two types of axion cosmologies are considered which generally differ in the order of two critical events: cosmic inflation and the PQ symmetry breaking [22, 23].
In scenario A inflation happens after the PQ symmetry breaking. One patch is thereby inflated to encompass our observable universe while smoothing \(\theta \) to a single initial value of the misalignment angle \(\theta _i\). Accordingly, the initial value of the axion field in our local universe is unique – up to quantum fluctuations – and it is fundamentally unpredictable from first principles. In this scenario, one can have the complete amount of cold DM in the form of cold axions for any value of \(f_a\gtrsim 10^9 \,\mathrm{GeV}\) assuming a suitable value of the initial universal misalignment angle \(\theta _i\), see [26]. Several examples for the resulting relic axion density today \(\rho _a\) are plotted as blue lines together with the observationally inferred cold DM matter density indicated by the horizontal dashed line in Fig. 3.
Relic axion DM density in the universe today \(\rho _a\) as a function of the axion mass \(m_a\) (equivalently \(f_a\)) for several values of the initial misalignment angle \(\theta _i\) in scenario A and scenario B (\({\mathcal {N}}=1\)) according to [22, 23]. Also shown is the thermal component whose contribution to \(\rho _a\) increases towards high mass values
In scenario B inflation happens before the PQ symmetry breaking. The axion field keeps a patchy structure from the PQ symmetry breaking until today as the initial conditions of the axion field were essentially random in each causally disconnected patch of the universe. Because of this, one can perform a statistical average to obtain a prediction for the relic axion density today from the realignment mechanism as a function of \(f_a\). However, scenario B is complicated by the presence of cosmic strings and domain walls, because the axion field forms a network of global cosmic strings after the PQ symmetry breaking. The ensuing axion domain wall problem is automatically solved when the domain wall number is \({\mathcal {N}}=1\) or by a suitable PQ symmetry breaking if \(\mathcal{N}>1\) [42]. In processes like string decays some energy converts into long-wavelength axions which will also contribute as DM. Assuming \({\mathcal {N}}=1\), the scenario B prediction from [23] is shown as a thick red line in Fig. 3 (the errors have been slightly enlarged as discussed in [27]). A recent direct calculation with an effective large string-tension technique favours instead a value smaller by a factor of 4, giving the correct abundance for \(m_a\simeq 26\, \upmu \hbox {eV}\) [28]. The recent study about the string network attractor and axion production [29] confirms a smaller value than [23] but highlights that the extrapolations needed are not under control by current simulations so that much larger values are possible. We therefore consider the mass range
to be best motivated one in scenario B with \(m_a\sim 100~\upmu \hbox {eV}\) as a typical corresponding value for the DM axion mass. Further discussions are given in [22, 23, 28, 29, 43,44,45,46,47].
We will aim to detect the DM axions bound to our galaxy which we assume to provide the full local galactic DM density of \((f_a m_a)^2\theta _0^2/2\sim 300~\mathrm {MeV}/\mathrm {cm}^3\). Their velocity dispersion on Earth is described by the galactic virial velocity \(v_a\sim 10^{-3}\). The corresponding de Broglie wavelength is \(\lambda _{\mathrm {dB}}=2\pi /(m_a v_a)=12.4~\mathrm {m}\,(100~\upmu \mathrm {eV}/m_a)(10^{-3}/v_a)\) and thereby of macroscopic size. Indeed, in our axion DM search experiment described below, we expect to probe an axion field that behaves as an (approximately) homogeneous and monochromatic classical oscillating field \(\theta \propto \theta _0 \cos (m_a t)\) with \(\theta _0\sim 4\times 10^{-19}\) and a frequency of \(\nu _a=m_a/(2\pi )\) in the microwave range.
3 Foundations of the experimental approach
The most sensitive experiments to date are based on cavity resonators in strong magnetic fields (Sikivie’s haloscopes [14]) such as ADMX [15], ADMX HF [18] or HAYSTAC [20]. However, these approaches are optimal for \(m_a\lesssim 40\,\upmu \mathrm eV\), which has been considered to be a substantial part of the natural range for axion DM in scenario A. If the resonance of the cavity is tuned to the axion mass, the cavity can be understood as a forced oscillator with a large axion-induced excitation. The length scale of the cavity needs to be approximately \(\lambda _a/2\) where \(\lambda _a=2\pi /m_a\) is the Compton wavelength given by the axion mass. As the emitted power of the cavity scales with the size of the cavity, this approach is impeded for small wavelengths and therefore small cavity sizes. For even lower values of \(m_a\) nuclear magnetic resonance techniques like CASPEr [48] or with LC circuits [49, 50], e.g. ABRACADABRA [51] and DM-Radio [54], could be effective.
The mass range favored in scenario B (2.5) and \(m_a\lesssim 40\,\upmu \mathrm eV\) in particular is not covered by current experiments with a sensitivity sufficiently high to probe QCD axion DM scenarios. In various proposals the cavity concept is extended to this mass range by employing higher mode resonators, such as in ORPHEUS [52], ORGAN [17] or RADES [53]. In addition, fifth-force experiments [55] could search in this region, but would not directly reveal the nature of DM.
In [30] a new concept to cover this important gap was introduced that is capable of discovering \(\sim 100\,\upmu \hbox {eV}\) mass axions. The main idea of this concept is to exploit constructive interference of electromagnetic radiation emitted at several surfaces as well as resonant enhancement. This is achieved through a series of parallel dielectric disks with a mirror on one side, all within a magnetic field \(\mathbf{B}_{\mathrm{e}}\) parallel to the surfaces as shown in Fig. 4 – a dielectric haloscope.
A dielectric haloscope consisting of a mirror and several dielectric disks placed in an external magnetic field \(\mathbf{B}_{\mathrm{e}}\) and a receiver in the field-free region. A focusing mirror (not shown) could be used to concentrate the emitted power into the receiver. Internal reflections are not shown. Figure taken with permission from [30]
As discussed in [30] the output power P of the dielectric haloscope per unit area A is
which implicitly depends linearly on the galactic axion DM density which is here assumed to make up all of the galactic cold DM density; cf. Sect. 2.4. Moreover, \(\beta ^2\) is the power boost factor that represents the enhancement of the output power of the dielectric haloscope with respect to the output power \(P_0\) of one single magnetized mirror only [31]. The value of \(\beta =\beta (\nu _a)\) as a function of frequency is calculated by matching the axion-induced electric field in each region (dielectric disk or vacuum) with left and right-moving electromagnetic waves of frequency \(\nu _a\) as imposed by the continuity of the total electric and magnetic fields parallel to the disk/mirror surface (\(\mathbf{E}_{||}\) and \(\mathbf{H}_{||}\), respectively) at the interfaces [56]. The quantum field calculation [57] of the power agrees with the classical calculation.
The desired enhancement, \(\beta ^2\gg 1\), comes from two effects, which generally act together but can be differentiated in limiting cases. These effects depend on the optical thickness of each disk \(\delta =2\pi \nu d \sqrt{\epsilon } \), where d is the physical thickness, \(\epsilon \) the dielectric constant, and \(\nu \) the frequency under consideration. This sets the transmission coefficient of a single disk, found to be \({\mathcal {T}}=i 2 \sqrt{\epsilon }/[i2\sqrt{\epsilon }\cos \delta +(\epsilon +1)\sin \delta ]\). When \(\delta =\pi ,3\pi ,5\pi ,\ldots \), the disk is transparent (\(|{\mathcal {T}}|=1\)) and the emission from different disks can be added constructively by placing them at the right distance. When \(|{\mathcal {T}}|< 1\), the spacings can be adjusted to form a series of leaky resonant cavities where E-fields are boosted by reflections between the disks. In general, both the simple sum of emitted waves and resonant enhancements are important.
After choosing \(\epsilon \) and the thickness of the disks d, the distances between disks remain as the only free parameters of the dielectric haloscope, still leaving considerable control over the frequency response. Different types of configurations are relevant: a configuration with a flat response over a large frequency range \(\Delta \nu \) reduces the need for frequent disk repositioning, but suffers from smaller power boost factors \(\beta ^2\). Configurations with a larger \(\beta ^2\) over a narrow range \(\Delta \nu \) allow to discard statistical fluctuations and do precision axion physics in case of a discovery.
Power boost factor \(\beta ^2(\nu _a)\) for configurations optimized for \(\Delta \nu _\beta =200,\, 50\,\,\mathrm{and}\,\,1~\mathrm {MHz}\) (red, blue and grey) centered on \(25\,\mathrm{GHz}\) using a mirror and 20 dielectric disks (\(d=1\,\mathrm{mm}\), \(\epsilon =25\)). Figure adapted from [30] with permission
The behavior of \(\beta ^2\) can be predicted using the area law: the integral \(\int \beta ^2 d\nu _a\) is constant for a fixed set of disks, which holds exactly when integrating over \(0\le \nu _a \le \infty \), and is a good approximation for frequency ranges containing the main peak [56]. This behaviour allows one to trade width for power and vice versa. In addition, an increase in the number of disks gives approximately a linear increase in \(\int \beta ^2 d\nu _a\). The area law is illustrated in Fig. 5 which shows \(\beta ^2(\nu _a)\) for a dielectric haloscope consisting of a mirror and 20 disks (\(d=1~\mathrm{mm}\), \(\epsilon =25\)). Spacings have been selected to maximize the power boost factor \(\beta ^2\) for three ranges of \(\Delta \nu \) with \(\Delta \nu _\beta =1,\,50\,\,\mathrm {and}\,\,200~\mathrm{MHz}\) each equally centered on \(25~\mathrm{GHz}\).
4 Proposed experimental setup for the search of dark matter axions
4.1 Design sensitivity and constraints from technology
The goal is to build a dielectric haloscope, based on the experimental concept described in Sect. 3, that is sensitive to axion DM in the mass range 40 to 400 \(\upmu \hbox {eV}\). The corresponding frequency range to be covered is roughly 10 to 100 GHz. The feasibility of achieving this goal is discussed in the following sections based on Eq. (3.1) and considering the constraints imposed by available technologies and materials.
Current state of the art electromagnetic receiver systems are able to detect signal powers of roughly \(1\times 10^{-22}\hbox { W}\) for a few days measurement time and for frequencies below 40 GHz. Such receiver systems are also used in radio astronomy applications. They have noise temperatures \(T_{\mathrm{rec}}\) of a few K. More details about the receiver are discussed in Sect. 4.2.
The magnetic field \(\mathbf{B}_{\mathrm{e}}\) needs to be parallel to the disk surface as introduced in Sect. 3. This requires ideally a dipole magnet that encloses the entire booster setup. To obtain a detectable power emission, a minimum value for the figure of merit \(B^2A\) is \(100\hbox { T}^2\hbox { m}^2\) , where \(B=B_{\mathrm{e}}\) here and below. The magnet will be discussed in more detail in Sect. 4.3.
The disks need to have high dielectric constants \(\epsilon \), and small dielectric losses \(\tan \delta \). They need to be mechanically stable such that disks with large surfaces and a few millimeter thickness can be manufactured. Several materials are considered for this purpose, for example LaAlO\(_3\), with \(\epsilon \approx 24 \) and \(\tan \delta \approx 10^{-6}\) at low temperatures [58, 59]. It seems realistic to manufacture tiled LaAlO\(_3\) disks of significant size, which is discussed in more detail in Sect. 4.4.
With these technological constraints, it follows from Eq. (3.1) that the power boost factor \(\beta ^2\) needs to exceed a value of \(\sim 10^4\) to make an axion signal detectable. The expected sensitivity and the measurement strategy are discussed in more detail in the sections below.
4.2 The receiver
The proposed principle of microwave detection for the frequency regime below \(\sim \,40\hbox { GHz}\) is based on heterodyne mixing of a preamplified signal [60]. This is sketched in Fig. 6. After the first low noise preamplifier stage (HEMT) and pre-filtering, the signal (RF) is shifted to intermediate frequencies (IF) by mixing a carrier frequency into the signal. At the intermediate frequencies the signal is further amplified and filtered. Finally, the signal is at a frequency that is accessible to digital 16 bit samplers, which have internal FPGAs that provide real time fast Fourier transform calculation with subsequent integration and storage of the signal.
Basic block diagram for heterodyne detection. By mixing the signal at frequency \(\nu \) with a local oscillator signal at frequency \(\nu _{\mathrm{LO}}\), the signal is shifted to \(\nu + \nu _{\mathrm{LO}}\) and \(\nu - \nu _{\mathrm{LO}}\). One of them is selected with a band-pass and successively detected
As mentioned above, state of the art detector technology requires different systems for the frequency ranges 10–40 GHz and above 40 GHz. For the lower frequencies, HEMT detectors [61], as widely used in the radio astronomy community, can be utilized. For the baseline design we propose HEMT receivers from Low Noise FactoryFootnote 2 for the lower frequency range. This frequency range is the initial focus of the experiment motivated by the mass region that is predicted for the DM axion, as discussed in Sect. 2.4. For the high frequency range new detectors working at the quantum noise limit or below still have to be identified and developed.
The sensitivity of the receiver can then be calculated using Dicke’s radiometer equation [62, 63],
where \(k_B\) is the Boltzmann constant. \(T_{\mathrm{sys}}\) is the total system noise temperature which consists of the receiver noise temperature \(T_{\mathrm{rec}}\) and the additional noise from the booster and its surroundings \(T_{\mathrm{booster}}\), such that \(T_{\mathrm{sys}} = T_{\mathrm{rec}} + T_{\mathrm{booster}}\). \(P_{\mathrm{sig}}\) is the expected photon signal power (3.1) corrected by the experimental efficiency, \(t_{\mathrm{scan}}\) is the scanning time for an individual measurement of a given bandwidth, and \(\Delta \nu =10^{-6}\nu \) is the predicted axion line width at given frequency \(\nu \).
Given the state of the art receiver noise temperature of \(T_{\mathrm{rec}}\approx 6\hbox { K} \) the noise of the remaining system, in particular the booster, should not exceed a few K. For the discussion in the following sections a value for the booster noise of \(T_{\mathrm{booster}} \approx 2\hbox { K}\) will be used. The noise of the booster is calculated from the actual physical temperature multiplied by its emissivity, i.e., its effectiveness in emitting thermal radiation. The emissivity equals the absorption coefficient. A perfect mirror would have no absorption and therefore a noise temperature of zero. Realistic systems with lossy disks will have finite emissivity and will therefore need cooling. Furthermore, the antenna and supporting structures thermally radiate. This can be suppressed by cooling the whole setup. These requirements can only be achieved with the booster being enclosed in a cryostat. With these boundary conditions the benchmark power of \(1\times 10^{-22}\hbox { W}\) can be detected by the receiver within a few days measurement time.
4.3 The magnet
According to Eq. (3.1), the emitted power is proportional to the square of the magnetic field component B parallel to the surface and the area A of the surface. Together with the necessity to collect the generated power by antennas facing the surfaces of the disks, this implies that a dipole field is preferred. When designing a magnet for the haloscope, the quantity \(B^2A\) is to be maximized. At the same time, the maximum length and width of the setup imposed by the coherence requirement, signal attenuation in the disks, and mechanical constraints need to be considered.
Taking the discussion in Sect. 4.4 into account, a dipole magnet suitable for the experiment should reach a \(B^2A\) value of \(100\hbox { T}^2\hbox { m}^2\) . This could be realized with a magnetic field strength of 10 T, with a bore of \(1\hbox { m}^{2}\) allowing to host disks of similar size. As discussed in Sect. 4.4 this field should extend over a length of up to 200 cm .
Two independent conceptual design studies are presently being finished. They are performed in the framework of an innovation partnership [64].
Both innovation partners have investigated several different dipole-magnet concepts: cosine-theta [65], canted cosine-theta [66], racetrack [67] and block designs [68]. They independently came to the conclusion that it is technologically feasible to produce a dipole magnet compatible with the required \(B^2A\) value of \(100\hbox { T}^2\hbox { m}^2\) and a field homogeneity of 5% within the geometrical boundary conditions set by the experiment and the infrastructure at the planned experimental site at DESY, Hamburg. Such a magnet would be built according to the block design using NbTi superconductor at 1.9 K. In order to respect the maximum peak field inside the coils consistent with NbTi superconductor, the magnetic field would be 9 T, while the disk diameter would be 1.25 m.
As a first step a demonstrator coil for verification of the feasibility of the proposed conceptual design will be built. First estimates of the time schedule indicate the possibility for a delivery of the full scale magnet to the experimental site around 2025.
4.4 The booster
The requirements for the booster follow from the design sensitivity and the constraints from receiver and magnet technologies which were discussed in the sections above. The signal power of the booster needs to be of the order of \(\gtrsim \,\) \(1\times 10^{-22}\hbox { W}\) to be detectable by state of the art radiometers. According to Eq. (3.1), the factor \(\beta ^2\) needs to exceed four orders of magnitude with a \(B^2A\) value of \(100\hbox { T}^2\hbox { m}^2\) , for example with a disk size of \(1\hbox { m}^{2}\) and magnetic field of 10 T.
Following the calculations outlined in Sect. 3, the power boost factor \(\beta ^2\) is determined using an idealized scenario with planar disks and without diffraction. Figure 7 shows the power boost factor \(\beta ^2\) as a function of frequency resulting from these calculations using 20 disks made from LaAlO\(_3\) (\(\epsilon =24)\). Six different configurations of disk spacings have been used. For each configuration the disk spacings are chosen such that the boost factor exceeds \(\beta ^2 > 2.5\times 10^3\) within a frequency range of \(\Delta \nu _\beta \sim \,250\,\hbox {MHz}\). For each configuration the calculation was repeated 250 times with Gaussian variations of the disks spacings with a precision of \(\sigma =15\,\upmu \hbox {m}\). This indicates that position uncertainties of 15 \(\upmu \hbox {m}\) are well acceptable in this frequency range, changing \(\beta ^2\) typically less than \(\sim 5 \%\).
The frequency at which sizable \(\beta ^2\) values occur in the range \(\Delta \nu _\beta \) can be seamlessly shifted by changing the spacings between the disks. The area law then implies that for a narrower \(\Delta \nu _\beta \) setting a higher power boost \(\beta ^2\) can be achieved.
Calculations of the power boost factor \(\beta ^2\) with 20 \(\hbox {LaAlO}_3\) disks (\(\epsilon =24 \)) for six different disk spacing configurations. For each configuration \(\beta ^2>2.5\times 10^3\) is achieved over a range of \(\Delta \nu _\beta \sim 250\) MHz. The 250 simulations performed with random Gaussian variations of the disks spacings with a precision of \(\sigma =15\,\upmu \hbox {m}\) are plotted on top of each other
Further idealized simulations showed that the power boost \(\beta ^2\) can easily exceed \(\sim 5\times 10^{4}\) for a setup with 80 disks [69]. Given the axion mass range to be covered, the distances between the disks range from \(\sim 1.5\hbox { mm}\) at 100 GHz to \(\sim 20\hbox { mm}\) at 10 GHz. The number of 80 disks would necessitate a length of the system of up to 200 cm (low frequency setup).
The booster could consist of movable disks connected to precision rails on which they can be positioned by precision motors via pistons. While the precision of the pistons of motors themselves can be easily controlled to the sub \(\upmu \hbox {m}\) level, the mechanical transmission from motors to disks in a high magnetic field and cryogenic environment as well as gravity can lead to sizable uncertainties in the exact disk positioning. Technology to ensure in-situ adjustable disk spacing with high enough precision in the experimental surrounding with 10 T magnetic field and cryogenic ambient temperature is currently being investigated and developed.
The material used for the dielectric disks has to fulfill the following criteria:
-
High dielectric constant \(\epsilon \gtrsim 10\): As discussed in [56] the output power can be increased with a higher dielectric constant \(\epsilon \), as the discontinuity of the axion-induced field on a disk surface increases. In addition, a higher \(\epsilon \) can enhance the boost factor by making the system more resonant. Moreover, the disks are more difficult to manufacture for high \(\epsilon \) as they need to be thinner for a given optical thickness \(\delta \) and their placement more precise. The optimal \(\epsilon \) is therefore a trade off between various effects.
-
Low dielectric loss tan \(\delta \lesssim 10^{-5}\): Similar calculations as in Sect. 3 and [56] have shown that up to 50% of the total output power in a 80 disk booster is lost for \(\tan {\delta } = 10^{-6}\) in the most resonant configurations. For more broadband configurations, higher losses with up to \(\tan \,\delta \sim 10^{-5}\) are acceptable.
-
Mechanically stable.
-
Appropriate cryogenic properties down to 4 K.
-
Affordable.
Presently lanthanum aluminate (\(\hbox {LaAlO}_3\)) is envisioned as the baseline candidate for its high permittivity (\(\epsilon \approx \) 24 ) and small loss (\(\tan \delta \approx \) \(10^{-6}\)) also at low temperatures [58, 59]. An alternative material could be sapphire (\(\hbox {Al}_2\hbox {O}_3\)) [70, 71] which has a permittivity of \(\epsilon \approx \) 11.5 and a loss angle \(\tan \delta \approx \) \(10^{-4}\). Other materials are under investigation.
The technology to produce sufficiently large disks with high enough precision (surface roughness of \(\sim \upmu \hbox {m}\)) needs to be developed. The concept of disk tiling is currently under investigation. Tiled disks are made from several smaller pieces of dielectric material that are glued or connected otherwise to form a single, stable large disk. Preliminary results from 3D simulations show that the emitted power of a tiled disk with gaps of \(\lambda _a / 10\) is not significantly reduced compared to the one emitted by a monolithic disk. Indeed, the emitted power is only reduced according to the smaller area of the tiled disk within the uncertainties of the simulation. Also first transmission measurements with a tiled ceramic disk showed no measurable effect.
An important task is to suppress contributions to the noise temperature \(T_{\mathrm{sys}}\) from the booster and its surrounding. As discussed in Sect. 4.2, the added system noise needs to be less than \(\sim \) 2 K. The main noise component is expected from thermal radiation of the disks with the support system, the walls surrounding the booster and the antenna. Therefore the booster needs to be enclosed in a cryogenic environment that allows to operate the booster at a temperature of 4 K.
A baseline design with 80 disks is assumed for the sensitivity study in Sect. 4.5. A schematic of the proposed MADMAX approach is shown in Fig. 8.
Preliminary baseline design of the MADMAX approach. The experiment can be divided into three parts: (1) magnet (red racetracks), (2) booster – consisting of the mirror (copper disk at the far left), the 80 dielectric disks (green) and the system to adjust disk spacing (not shown) – (3) the receiver – consisting of the horn antenna (yellow) and the cold preamplifier inside a separated cryostat. The focusing mirror is shown as an orange disk at the right. The figure is not to scale
The experimental setup can be divided into the three main components:
-
The dipole magnet with a \(B^2A\) value of \(100\hbox { T}^2\hbox { m}^2\) over a length of 2 m,
-
the booster, consisting of a mirror (\(\epsilon = \infty \)) at the far end and the \(\sim \) 80 dielectric disks that can be positioned within a few \(\upmu \hbox {m}\) precision by motors,
-
the receiver, including the focusing mirror and the antenna, which is used for detection of the emitted power.
As discussed in Sect. 4.2 the initial focus of the experiment is in the frequency range 10–40 GHz. The extension to higher frequencies will be done at a later stage. For higher frequencies diffraction effects are expected to become less pronounced but the mechanical precision requirements on the booster setup will become more demanding.
4.5 Expected sensitivity and measurement strategy
The sensitivity of the proposed setup is calculated from the baseline design discussed in the previous sections. This estimate assumes that a power boost factor of \(\beta ^2\) \(\sim 5\times 10^{4}\) over a bandwidth of \(\Delta \nu _{\beta }\sim \) 50 MHz can be achieved with 80 LaAlO3 disks with a surface area of \(1\hbox { m}^{2}\) in a 10 T magnetic field. For the receiver a detection efficiency of 80% and a measurement time of \(\sim 4\) days , system noise temperature of 8 K and minimum signal-to-noise ratio of \(S/N = 4\) for each frequency band are assumed.
The resulting sensitivities obtainable with the MADMAX approach for DM axions and hidden photons with a mass in the range 40 to 400 \(\upmu \hbox {eV}\) using the above assumptions and the Dicke equation (4.1) are shown in Figs. 9 and 10, respectively. A significant part of the parameter space predicted for DM axions in the post inflationary PQ scenario could be probed. For hidden photons, the kinetic mixing angle \(\chi \) is analogous to \(g_{a\gamma }\) and the search does not require a magnetic field [31, 75]. Also a parameter space consistent with hidden photons as DM could be probed down to \(\chi \lesssim 10^{-15}\).
Projection of sensitivities for DM axions and ALPs on the axion–photon coupling \(g_{a\gamma }\) as a function of the axion mass. The lines denoted by DFSZ and KSVZ show representative \(g_{a\gamma }\) values associated with the corresponding two most popular classes of QCD axion models. For the MADMAX projection, a setup with 80 dielectric disks each with an area of \(1\hbox { m}^{2}\) and a magnetic field of 10 T parallel to the disk surfaces has been assumed. Also shown are sensitivity projections for prototype setups with 5 and 20 disks both with 30 cm disk diameter in a 3 T magnetic field. In addition, an approximate projection of the reach of future cavity experiments is shown. The projected sensitivities are compared to existing limits from ADMX [15, 16], other haloscope experiments [13], from HAYSTAC [18] and ORGAN [17]. Also the IAXO [72] sensitivity for solar axions and ALPs is indicated
Projection of sensitivities for hidden photons on the kinetic mixing parameter \(\chi \) as a function of the hidden photon mass. For the MADMAX projection, a setup using 80 lanthanum aluminate disks each with an \(1\hbox { m}^{2}\) area have been assumed. Also shown are sensitivity projections for prototype setups with 5 and 20 disks with 30 cm disk diameter. The projected sensitivities are compared to existing limits from ADMX and other haloscope experiments for hidden photon searches from [73], from ADMX-HF [18] and from the latest Tokyo results [74]. The area above the black line represents the parameter space where hidden photons are not a good DM candidate [73]
The measurement strategy depends on the required measurement time to detect a \(1\times 10^{-22}\hbox { W}\) signal with the desired significance and the time needed to readjust the disk spacings to change the frequency band of the power boost factor \(\beta ^2\). The Dicke equation (4.1) suggests that the measurement time for a scan over a fixed frequency range is inversely proportional to the square of the signal power \(P_{\mathrm{sig}}\), where \(P_{\mathrm{sig}}\) itself is proportional to \(\beta ^2\). The measurement time is further proportional to the number of individual scans per GHz, given by \(1 \mathrm \ GHz / \Delta \nu _\beta \), such that the total measurement time is inversely proportional to \(\beta ^4\Delta \nu _\beta \). Since the area law suggests \(\beta ^2 \Delta \nu _\beta \sim \mathrm{const}\), it is in principle favorable to make \(\beta ^2\) big and \(\Delta \nu _\beta \) small, until the measurement times become comparable to the readjustment times for the disks. Increasing the boost factor further decreases \(\Delta \nu _\beta \) and thus requires more readjustments, which in turn increase the total scan time again.
The readjustment time, during which no data is taken, is conservatively estimated to be around a day. The measurement time further depends on the system noise which is assumed to be \(T_{\mathrm{sys}} = \) 8 K and the detection efficiency, for which we assume \(\sim 80\% \). Note that the numbers stated in the above considerations are preliminary estimates with respective uncertainties. Under the stated assumptions one finds that the mass range between 40 and 120 \(\upmu \hbox {eV}\) could be scanned within \(\sim 5\) years [56], showing the experimental feasibility of this approach. The mass range above 120 \(\upmu \hbox {eV}\) requires additional R&D especially for the detection technique and could be covered with detectors working at or below the quantum limit for the required frequency range.
5 Proof of principle measurements with first test setup
First proof of principle systems for the booster and the receiver have been assembled and tested. A receiver system based on a HEMT preamplifier and heterodyne mixing as described in Sect. 4.2 has been set up. Additionally, a first proof of principle booster with up to 5 sapphire disks has been built and the electromagnetic response was tested for different cases of equidistant disk positions.
The setups were used for first proof of principle measurements, and are described in more detail in the following subsections. These measurements indicate that the assumptions on 10–30 GHz receiver sensitivity and disk placement precision, necessary to estimate the sensitivity of the MADMAX approach, are realistic.
5.1 The proof of principle detection system
The detection system of the “proof of principle setup” consists of a three-stage heterodyne receiver with subsequent Fast-Fourier signal analysis (Fig. 11). The high sensitivity of the receiver is achieved by an InP-HEMT operating at an ambient temperature of 4 K. The amplifier has a noise temperature of 5–6 K and a gain of 33 dB, which is sufficient to determine the noise performance of the receiver. Afterwards the frequency down-conversion is done at room temperature to a center frequency of 26 MHz with a total bandwidth of approximately 50 MHz. Data acquisition happens using four time-shifted digital 16 bit samplers with a sampling rate of \(200\times 10^6/\hbox {s}\) and internal FPGAs for real time FFT calculation and subsequent averaging. This method allows the reduction of the system dead-time from 75% to less than 1%. The bin-width of the Fourier transform is 2.048 kHz.
First measurements with the receiver have been performed. A “fake-axion” signal with a level of \(\sim \,1.2\times 10^{-22}\) W and a bandwidth of about 10 kHz was injected. The 4K background temperature of the signal injection was determined by the liquid helium environment. This fake axion signal could be detected in a cross-correlation within two days measurement time with \(\gtrsim \,4.8\,\sigma \) separation from background. The power spectrum is shown in Fig. 12. The receiver thus meets the first expectations. Further improvements to reduce the system noise temperature are ongoing.
Test signal at 18.4 GHz and a power of \(\sim \,1.2\times 10^{-22}\) W recorded with the presented receiver setup. The region of the signal is shown in the inset together with the background fit (top inset) and the residuals from the background fit (lower inset). The test signal is detected with a significance of \(\gtrsim \,4.8\,\sigma \). The arrow indicates the location of the inset. Adapted from [76]
5.2 The proof of principle booster
As outlined in previous sections, the power boost factor \(\beta ^2\) can be calculated, considering the axion-induced emitted E-field amplitude from each individual disk and the propagation of each of these signals throughout the booster [56]. This implies that transmissivity and reflectivity of the haloscope are correlated to the boost factor curve. As the boost factor cannot be measured directly, the correlation with the group delay, transmissivity and reflectivity is exploited. Hence, transmissivity and reflectivity can be used to verify the simulated boost factor behavior and support the disk placement procedure during the actual operation of the experiment. In an ideal loss-less booster the magnitude of the reflectivity will always be unity. Therefore, it is more feasible to consider its phase or the group delay \(\tau _g = - d \Phi / d \omega \), with \(\Phi \) the phase of the reflected signal and \(\omega \) the angular frequency. The group delay can be qualitatively understood as the mean retention time of reflected photons within the booster, mapping out resonances. The correlation between boost factor and group delay is shown in Fig. 13 (right) for a set of four equally spaced disks at 7 mm distances. In such a case it manifests predominantly in the correlation to the group delay peak at the highest frequency.
In order to show that a booster with the predicted electromagnetic properties can actually be built and to study effects that not accounted for in the idealized 1D calculations, the prototype setup shown in Fig. 13 (left) has been developed. It consists of up to five sapphire disks placed in front of a copper mirror. The disks have a dielectric constant of \(\epsilon \approx 9.4\) perpendicular to the beam axis, a thickness of 1 mm, and a diameter of 200 mm. Precision motors change their position with an accuracy of a few \({\upmu \mathrm m}\) after accounting for temperature effects and mechanical hysteresis. The phase and amplitude of a reflected signal at a given frequency can be measured using a Vector Network Analyzer (VNA) connected to the antenna shown in Fig. 13.
The temporal stability was investigated using long term (\(\sim 15\) h) reflectivity measurements with up to 4 installed disks without any disk movement. The frequency stability of a single observed group delay peak was on the order of \(\pm \,2\,\hbox { MHz}\). This corresponds to an uncertainty in disk position of less than a micrometer. The variations are attributed to mechanical vibration or thermal contraction in the setup. Compared to the envisioned boost factor bandwidth of 50 MHz, this indicates that long-term stability of the system is sufficient even under without active vibrational damping and with temperature fluctuations of the order \(\pm 1\,{^{\circ }}\hbox {C}\).
Reproducibility of fit results. Left: Motor position offsets \(d_i\) after fitting the physical disk positions such that the measured group delay matches the simulation. Right: Boost factor amplitude and position variation after fitting the model to each of the measured group delays corresponding to the data points in the left plot
The configuration of physical disk positions is found by matching the group delay of the system to the prediction of the 1D model. To this end optimization schemes need to be employed, minimizing the number of function evaluations – corresponding to a realignment of the setup and measurement of the electromagnetic response – while avoiding convergence in local minima. Simple implementations of a genetic [77] and Nelder–Mead [78] algorithm have been tested. The convergence criterion requires changes of the motor positions of less than a \(\upmu \hbox {m}\). Figure 13 (right) shows a typical group delay fit for a case of four equidistant disks at 7 mm distance. For disk spacings of 8 mm the situation corresponds to a maximal power boost of \(\sim 700\) at a frequency of \(\approx 22.4\hbox { GHz}\) with a FWHM of \(\sim 180\hbox { MHz}\). While the Nelder–Mead algorithm converges significantly faster, the genetic algorithm seems to be less prone to converge to local minima. Figure 14 shows the distribution of motor positions after repeating the optimization multiple times. While the repeatability in single spacings is better than \(\sim 40\hbox { mm}\), the electromagnetic response is degenerate in the disk spacings, such that higher disk separations at the one end can be partially compensated by smaller spacings on the other end of the booster. To infer the effect on the power boost factor, the disk positions in the model are optimized such that the model predicts the various measured group delays. The change in frequency and power boost are outlined in Fig. 14, being \(\Delta \beta ^2_{\mathrm{max}} \approx 10\, \%\,\beta ^2_{\mathrm{max}}\) and \(\Delta f \approx 10\, \%\,\mathrm{FWHM}\). We conclude that our system can be aligned to match the predicted response and achieve the desired boost factors within acceptable accuracy for up to five disks at equidistant spacings of 6–9 mm. A more detailed paper on this setup is in preparation.
6 Towards realization of MADMAX
6.1 Prototype
The receiver sensitivity has been verified experimentally as discussed in Sect. 5.1, while a basic test of the precision of disk placement has been performed for a setup with four disks of 20 cm diameter and a mirror as discussed in Sect. 5.2. Before a full scale experiment can be built, many components still need to be investigated and developed. The full R&D programme of the coming years is beyond the scope of this paper. Some of the ongoing investigations include the following:
-
All proposed components have to be tested for their performance in a strong magnetic field of up to 10 T and at cryogenic temperatures of 4 K.
-
For the final size of the experiment the required accuracy of relevant parameters (precision of disk positioning, disk thickness, surface roughness, loss mechanisms) need to be tested against available technology.
-
A technology to produce thin dielectric disks with plane surfaces with areas up to \(1\hbox { m}^{2}\) has to be developed and tested, e.g., disk tiling.
-
Procedures to measure the properties of dielectric disks such as permittivity and loss factor need to be adapted.
-
A concept to position the disks inside a strong magnetic field in vacuum and at cryogenic temperatures down to 4 K has to be developed.
-
The system noise behavior has to be studied down to temperatures around 4 K, including the noise behaviour of the booster itself and its surroundings (tube, holding structure).
-
The simulation of the experiment needs to be tested for realism up to the full scale of the experimental device. The preliminary 1D calculations need to be extended to realistic full 3D simulations.
-
The scaling behavior of the power boost factor \(\beta ^2\) with the number of disks and their area has to be studied further. The area law (Sect. 3) holds in 1D, while effects such as diffraction, dielectric loss and others may modify the behavior.
-
The beam shape of the system needs to be studied, and a suitably matched antenna system needs to be devised.
-
The receiver technology for low frequencies, based on heterodyne mixing needs to be optimized, while new technologies for high frequencies need to be explored.
-
The feasibility of manufacturing a dipole magnet fulfilling the requirements of the experiment needs to be studied in terms of cost and availability of technology.
The central component towards accomplishing these goals and to obtain a better understanding of the fundamental concept of the experiment will be a prototype system with smaller dimensions. The prototype setup will have a smaller number of disks (\(\approx 20\)) each with a smaller diameter (\(\approx 30\) cm) than in the full scale experiment.
This prototype booster will be used to study adjustment of disk positions for a defined frequency and bandwidth. The cryogenic performance of the mechanical parts will be studied in a dedicated cryostat that allows the components to be cooled down to 4 K. It is also foreseen to test the prototype booster inside magnetic fields of a few T. It is presently being investigated whether a suitable magnet could be available.
The prototype represents a stepping stone towards the development of technologies to be used in the full experiment. Beyond that, the prototype will also provide competitive physics results, covering regions in the axion DM phase space that have not been probed experimentally before, if a suitable magnet can be found.
As shown in Fig. 9, with a setup consisting of five disks with 30 cm diameter in front of a mirror inside a 3 T magnetic field, a sensitivity could be achieved that can probe uncovered regions of DM parameter space, and which exceeds the projected sensitivity of the proposed IAXO experiment for solar axions [72], which does not depend on cosmological assumptions. A setup with 20 disks improves the sensitivity on \(g_{a\gamma }\) a factor of two compared to a five disk setup.
As shown in Fig. 10, even without a magnet, a prototype setup could considerably improve the existing limits in the search for DM hidden photons and probe into unexplored territory in the allowed parameter space. Even a five disk setup would improve the limit obtained in reference [74] for \(\sim \,50\,\upmu \hbox {eV}\) hidden photons by more than two orders of magnitude.
6.2 Experimental site
DESY Hamburg has offered the MADMAX collaboration to host the experiment at the HERA north hall. It has been verified to be a suitable site for the experiment: It fulfills the space and infrastructural requirements and is \(\sim \,20\,\hbox {m}\) below the surface. It has enough overburden to sufficiently shield electromagnetic radiation present at the surface. First background measurements at the site in the frequency range between few kHz and \(\sim \,20\,\hbox {GHz}\) have been performed. Above 1 GHz the measured background consistently had a level \(< -100\,\mathrm{dBm}\); no signal could be detected. Between 100 MHz and 1 GHz some signals from radio stations, telecommunication and emergency communication transmitters are present, but also in this frequency range the general noise was consistently less than \(-100\) dBm. No correlations with RF activities of the PETRA and FLASH RF infrastructure – ongoing during the measurements – were found. The cryogenic infrastructure necessary for the magnet and booster operation already exists and needs to be adapted. Furthermore, the iron yoke of the H1 detector is still in the hall and could be used as yoke for the MADMAX magnet.
6.3 Timeline
As first steps it is planned to answer scientific and strategically important questions that have the potential to influence the design of the experiment. They will be addressed within the next 3–4 years using the prototype setup described above. Also a demonstrator magnet is planned that will prove the feasibility of the technology. Already during this time, physics results will be achieved using the prototype cryogenic booster.
Based on the results from the prototype studies a final design will be devised. It is envisioned to start building the final experiment once results from the magnet demonstrator setup and MADMAX prototype experiment are available, approximately in the year \(\sim \,2022\). The time scale to start data taking is mainly driven by the production of the magnet.
The plan outlined in this paper would allow to probe the axion DM mass range between \(\sim \,40\) and \(120\,\upmu \hbox {eV}\). Until then new detection techniques with quantum limited detectors would be developed to allow the sensitivity range of the experiment to be extended up to an axion mass of \(\,\sim \,400\,\upmu \hbox {eV}\).
7 Conclusions
Axions are very well motivated particle candidates that can explain both the strong CP problem and the DM problem simultaneously. Their coupling to photons through the Primakoff effect makes them detectable in principle in the laboratory. This has been and is being exploited in experiments relying on the concept of resonant axion to photon conversion in cavities. These experiments are sensitive enough to probe axions as DM candidates in the axion mass range below \(\sim \,40\,\upmu \hbox {eV}\). The axion mass range above \(40\,\upmu \hbox {eV}\), which is predicted by theoretical models where the PQ symmetry breaking occurs after inflation, is not yet experimentally explored.
We propose a new experiment, MADMAX, a dielectric haloscope. We have shown that simulations and first experimental tests of the concept are very promising. This lead us to the conclusion that this approach is experimentally scalable. We introduced the baseline design of the MADMAX experiment. This experiment consists of three main components:
-
1.
A booster with \(\sim 80\) disks with area \(\sim \,1\,\hbox {m}^2\) made from a material with high dielectric constant and low dielectric loss in front of a mirror. The distances between the disks need to be adjustable in a range from 2–20 mm with a precision of a few \(\upmu \hbox {m}\).
-
2.
A magnet with an aperture to host the booster. The magnetic field parallel to the disks along with the size of the disk area needs to achieve a \(B^2A\) value of \(100\hbox { T}^2\hbox { m}^2\) .
-
3.
Receivers that can detect microwaves with a power of \(\sim \,10^{-22}\) W in a few days of measurement time in the range 10–\(100\,\mathrm{GHz}\).
The whole setup needs to be installed in an environment with low electromagnetic noise. Presently the HERA hall north at DESY, Hamburg has been identified as a site.
In the next 2–3 years a smaller prototype with disk diameters of \(\sim \,30\,\hbox {cm}\) will be designed and produced. This will allow to verify the scalability of the technologies investigated so far. Such a setup would probe uncovered parameter space and provide competitive results in the search for hidden photons and also for ALPs if a suitable magnet can be identified.
Once the prototype is commissioned, the construction of the final experiment will be envisaged, taking the experience with the prototype into account. In case of a smooth implementation, first measurements with a sensitivity high enough to probe DM QCD axions could be taken starting from \(\sim \,2025\). It would need roughly ten years to probe the whole mass range between 40 and 400 \(\upmu \hbox {eV}\) predicted for axion DM in the case of PQ symmetry breaking after inflation. This proposal presents the so far only known approach to cover this very well motivated mass range for axions and is complementary to other axion DM searches discussed in the literature.
Data Availability Statement
This manuscript has no associated data or the data will not be deposited. [Authors’ comment: The white paper describes a plan for a future experiment, which is why no data is provided.]
Notes
Strictly speaking, this would only happen if \(\delta _{13}=0\) but CP violation is transmitted by quantum corrections to the QCD sector and the minimum gets shifted from \(\theta =0\) by a small amount. See [35] for a review.
References
R.D. Peccei, H.R. Quinn, Phys. Rev. Lett. 38, 1440 (1977)
R.D. Peccei, H.R. Quinn, Phys. Rev. D 16, 1791 (1977)
S. Weinberg, Phys. Rev. Lett. 40, 223 (1978)
F. Wilczek, Phys. Rev. Lett. 40, 279 (1978)
J. Preskill, M.B. Wise, F. Wilczek, Phys. Lett. B 120, 127 (1983)
L.F. Abbott, P. Sikivie, Phys. Lett. B 120, 133 (1983)
M. Dine, W. Fischler, Phys. Lett. B 120, 137 (1983)
P. Sikivie, Lect. Notes Phys. 741, 19 (2008). arXiv:astro-ph/0610440
D.J.E. Marsh, Phys. Rep. 643, 1 (2016). arXiv:1510.07633
G. Raffelt, Lect. Notes Phys. 741, 51 (2008)
J.H. Chang, R. Essig, S.D. McDermott, JHEP 1809, 051 (2018). arXiv:1803.00993
M. Giannotti, I.G. Irastorza, J. Redondo, A. Ringwald, K. Saikawa, JCAP 1710(10), 010 (2017). arXiv:1708.02111
A. Ringwald, L. Rosenberg, G. Rybka, M. Tanabashi et al., [Particle Data Group], Phys. Rev. D 98(3), 030001 (2018)
P. Sikivie, Phys. Rev. Lett. 51, 1415 (1983) (erratum ibid. 51, 695, 1983)
S. Asztalos et al., Phys. Rev. D 69, 011101 (2004)
N. Du et al., [ADMX Collaboration], Phys. Rev. Lett. 120(15), 151301 (2018). arXiv:1804.05750
B.T. McAllister, G. Flower, E.N. Ivanov, M. Goryachev, J. Bourhill, M.E. Tobar, Phys. Dark Univ. 18, 67 (2017). arXiv:1706.00209
B.M. Brubaker, Phys. Rev. Lett. 118(6), 061302 (2017). arXiv:1610.02580
S. Al Kenany, Nucl. Instrum. Methods A 854, 11 (2017). arXiv:1611.07123
L. Zhong et al., [HAYSTAC Collaboration], Phys. Rev. D 97(9), 092001 (2018). arXiv:1803.03690
W. Chung, Launching axion experiment at CAPP/IBS in Korea. In: Proceedings of the 12th Patras Workshop on Axions, WIMPs and WISPs, Jeju (2016)
M. Kawasaki, K. Saikawa, T. Sekiguchi, Phys. Rev. D 91(6), 065014 (2015). arXiv:1412.0789
T. Hiramatsu, M. Kawasaki, K. Saikawa, T. Sekiguchi, Phys. Rev. D 85, 105020 (2012) (erratum ibid. 86, 089902, 2012)
E.W. Kolb, I.I. Tkachev, Phys. Rev. D 49, 5040 (1994)
K.M. Zurek, C.J. Hogan, T.R. Quinn, Phys. Rev. D 75, 043511 (2007)
S. Borsanyi et al., Nature 539, 69 (2016)
G. Ballesteros, J. Redondo, A. Ringwald, C. Tamarit, JCAP 1708(08), 001 (2017). arXiv:1610.01639
V.B. Klaer, G.D. Moore, JCAP 1711(11), 049 (2017). arXiv:1708.07521
M. Gorghetto, E. Hardy, G. Villadoro, JHEP 1807, 151 (2018). arXiv:1806.04677
A. Caldwell et al., [MADMAX Working Group], Phys. Rev. Lett. 118(9), 091801 (2017). arXiv:1611.05865
D. Horns, J. Jaeckel, A. Lindner, A. Lobanov, J. Redondo, A. Ringwald, JCAP 1304, 016 (2013). arXiv:1212.2970
J. Jaeckel, J. Redondo, Phys. Rev. D 88, 115002 (2013). arXiv:1308.1103
M. Pospelov, A. Ritz, Nucl. Phys. B 573, 177 (2000). arXiv:hep-ph/9908508
C.A. Baker, Phys. Rev. Lett. 97, 131801 (2006). arXiv:hep-ex/0602020
M. Pospelov, A. Ritz, Ann. Phys. 318, 119 (2005). arXiv:hep-ph/0504231
C. Vafa, E. Witten, Phys. Rev. Lett. 53, 535 (1984)
G. Grilli di Cortona, E. Hardy, J. Pardo, G. Villadoro Vega, JHEP 1601, 034 (2016). arXiv:1511.02867
L. Di Luzio, F. Mescia, E. Nardi, Phys. Rev. Lett. 118(3), 031801 (2017). https://doi.org/10.1103/PhysRevLett.118.031801. arXiv:1610.07593 [hep-ph]
P. Agrawal, J. Fan, M. Reece, L.T. Wang, JHEP 1802, 006 (2018). https://doi.org/10.1007/JHEP02(2018)006. arXiv:1709.06085 [hep-ph]
M. Giannotti, I. Irastorza, J. Redondo, A. Ringwald, JCAP 1605(05), 057 (2016). arXiv:1512.08108
I.G. Irastorza, J. Redondo, Prog. Part. Nucl. Phys. 102, 89 (2018). arXiv:1801.08127
P. Sikivie, Phys. Rev. Lett. 48, 1156 (1982)
R. Daido, F. Takahashi, W. Yin, arXiv:1702.03284
A. Ringwald, K. Saikawa, Phys. Rev. D 93, 085031 (2016). arXiv:1512.06436 (addendum ibid.94, 049908, 2016)
L. Fleury, G.D. Moore, JCAP 1601, 004 (2016). arXiv:1509.00026
L.M. Fleury, G.D. Moore, JCAP 1605, 005 (2016). arXiv:1602.04818
G.D. Moore, arXiv:1604.02356
D. Budker, P.W. Graham, M. Ledbetter, S. Rajendran, A. Sushkov, Phys. Rev. X 4, 021030 (2014). arXiv:1306.6089
P. Sikivie, N. Sullivan, D.B. Tanner, Phys. Rev. Lett. 112, 131301 (2014). arXiv:1310.8545
Y. Kahn, B.R. Safdi, J. Thaler, Phys. Rev. Lett. 117, 141801 (2016). arXiv:1602.01086
J.L. Ouellet et al., arXiv:1810.1225
G. Rybka, A. Wagner, A. Brill, K. Ramos, R. Percival, K. Patel, Phys. Rev. D 91(1), 011701 (2015). arXiv:1403.3121
A.A. Melcon, JCAP 1805(05), 040 (2018). arXiv:1803.01243
M. Silva-Feaver, IEEE Trans. Appl. Superconduct. 27(4), 1400204 (2017). arXiv:1610.09344
A. Arvanitaki, A.A. Geraci, Phys. Rev. Lett. 113, 161801 (2014). arXiv:1403.1290
A.J. Millar, G.G. Raffelt, J. Redondo, F.D. Steffen, JCAP 1701(01), 061 (2017). arXiv:1612.07057
A.N. Ioannisian, N. Kazarian, A.J. Millar, G.G. Raffelt, JCAP 1709(09), 005 (2017). arXiv:1707.00701
J. Krupka, IEEE Trans. Microw. Theory Tech. 42, 10 (1994)
T. Shimada, IEEE Trans. Ultrason. Ferroelectr. Freq. Control 57, 10 (2010)
T. Oxley, IEEE Trans. Microw. Theory Tech. 50(3), 867 (2002)
T. Mimura, IEEE Trans. Microw. Theory Tech. 50(3), 780 (2002)
T. Hunter, R. Kimberk, arXiv:1507.04280
J. Kraus, Antennas and wave propagation (Mc Graw Hill, New York, 2010). ISBN0070671559
L. Rossi, IEEE Trans. Appl. Superconduct. 14(2), 153 (2004)
S. Caspi, IEEE Trans. Appl. Superconduct. 24(3), 4001804 (2014)
E. Rochepault, P. Vedrine, F. Bouillault, IEEE Trans. Appl. Superconduct. 22(3), 4900804 (2012)
E. Rochepault, P. Vedrine, F. Bouillault, IEEE Trans. Appl. Superconduct. 22, 3 (2012)
A.J. Millar, J. Redondo, F.D. Steffen, JCAP 1710(10), 006 (2017). arXiv:1707.04266 (erratum: JCAP 1805(05), E02, 2018)
J. Krupka et al., Meas. Sci. Technol. 10, 387 (1999)
X. Aupi, J. Appl. Phys. 95(5), 2639 (2004)
E. Armengaud et al., JINST 9, T05002 (2014)
P. Arias et al., JCAP 06, 013 (2012)
J. Suzuki, Y. Inoue, T. Horie, M. Minowa, Proceedings Contribution to the 11th Patras Workshop on Axions, WIMPs and WISPs, Zaragoza, 22–26 June 2015 (2015). arXiv:1509.00785
J. Jaeckel, Frascati Phys. Ser. 56, 172 (2012). arXiv:1303.1821
F. Beaujean, A. Caldwell, O. Reimann, Eur. Phys. J. C 78(9), 793 (2018). arXiv:1710.06642
D. Whitley, Stat. Comput. 4, 65 (1994)
J.C. Lagarias, J.A. Reeds, M.H. Wright, P.E. Wright, SIAM J. Optim. 9(1), 112–147 (1998)
Acknowledgements
The prototype setup used for first measurements was partly funded as a seed project by the DFG Excellence Cluster Universe (Grant no. EXC 153). Chang Lee is supported by DFG through SFB 1258.
Author information
Authors and Affiliations
Consortia
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
Funded by SCOAP3
About this article
Cite this article
MADMAX Collaboration., Brun, P., Caldwell, A. et al. A new experimental approach to probe QCD axion dark matter in the mass range above \({ 40}\,{\upmu }\mathrm{{eV}}\). Eur. Phys. J. C 79, 186 (2019). https://doi.org/10.1140/epjc/s10052-019-6683-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1140/epjc/s10052-019-6683-x