CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 1 Croix contrevrentement
PIECE: 191 Diagonale Contreventement_191 POINT: 7 COORDONNEE: x =
1.00 L = 4.34 m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /6/ 10*1.08 + 15*1.35 + 18*1.50 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: CAE 120x12

h=12.0 cm gM0=1.00 gM1=1.00
b=12.0 cm Ay=14.40 cm2 Az=14.40 cm2 Ax=27.54 cm2
tw=1.2 cm Iy=367.67 cm4 Iz=367.67 cm4 Ix=13.13 cm4
tf=1.2 cm Wely=42.75 cm3 Welz=42.75 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 0.28 kN My,Ed = -9.00 kN*m
Nc,Rd = 647.19 kN My,Ed,max = -9.00 kN*m
Nb,Rd = 530.86 kN My,c,Rd = 10.05 kN*m Vz,Ed = -3.61 kN
Vz,c,Rd = 195.38 kN
Classe de la section = 3
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 2.17 m Lam_y = 0.63 Lz = 2.17 m Lam_z = 0.63
Lcr,y = 2.17 m Xy = 0.82 Lcr,z = 2.17 m Xz = 0.82
Lamy = 59.43 kyy = 1.00 Lamz = 59.43 kzy = 1.00
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
My,Ed/My,c,Rd = 0.90 < 1.00 (6.2.5.(1))
N,Ed/Nc,Rd + My,Ed/My,c,Rd = 0.90 < 1.00 (6.2.1(7))
Vz,Ed/Vz,c,Rd = 0.02 < 1.00 (6.2.6.(1))
Contrôle de la stabilité globale de la barre:
Lambda,y = 59.43 < Lambda,max = 210.00 Lambda,z = 59.43 < Lambda,max = 210.00 STABLE
N,Ed/(Xmin*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) = 0.90 < 1.00 (6.3.3.(4))
N,Ed/(Xmin*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) = 0.90 < 1.00 (6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 2 Poteaux
PIECE: 51 Poteau_51 POINT: 1 COORDONNEE: x = 0.00 L = 0.00
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /24/ 9*1.80 + 15*1.35 + 18*1.05 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 330

h=33.0 cm gM0=1.00 gM1=1.00
b=16.0 cm Ay=42.28 cm2 Az=30.81 cm2 Ax=62.61 cm2
tw=0.8 cm Iy=11766.90 cm4 Iz=788.14 cm4 Ix=28.28 cm4
tf=1.1 cm Wply=804.33 cm3 Wplz=153.68 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 13.49 kN My,Ed = 129.14 kN*m
Nc,Rd = 1471.34 kN My,Ed,max = 129.14 kN*m
Nb,Rd = 340.37 kN My,c,Rd = 189.02 kN*m Vz,Ed = -36.46 kN
MN,y,Rd = 189.02 kN*m Vz,c,Rd = 418.06 kN
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 6.30 m Lam_y = 0.49 Lz = 6.30 m Lam_z = 1.89
Lcr,y = 6.30 m Xy = 0.93 Lcr,z = 6.30 m Xz = 0.23
Lamy = 45.95 kyy = 1.01 Lamz = 177.57 kzy = 0.52
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd = 0.01 < 1.00 (6.2.4.(1))
My,Ed/My,c,Rd = 0.68 < 1.00 (6.2.5.(1))
Vz,Ed/Vz,c,Rd = 0.09 < 1.00 (6.2.6.(1))
Contrôle de la stabilité globale de la barre:
Lambda,y = 45.95 < Lambda,max = 210.00 Lambda,z = 177.57 < Lambda,max = 210.00 STABLE
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) = 0.70 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) = 0.40 < 1.00 (6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 3 Potelets
PIECE: 16 Poteau_16 POINT: 7 COORDONNEE: x = 1.00 L = 5.66
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /25/ 10*1.80 + 15*1.35 + 18*1.05 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 270

h=27.0 cm gM0=1.00 gM1=1.00
b=13.5 cm Ay=31.46 cm2 Az=22.14 cm2 Ax=45.95 cm2
tw=0.7 cm Iy=5789.78 cm4 Iz=419.87 cm4 Ix=16.02 cm4
tf=1.0 cm Wply=484.00 cm3 Wplz=96.95 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 17.25 kN Mz,Ed = 1.23 kN*m Vy,Ed = -2.60 kN
Nc,Rd = 1079.83 kN My,Ed,max = 0.86 kN*m Mz,Ed,max = 1.23 kN*m Vy,c,Rd = 426.79 kN
Nb,Rd = 225.96 kN My,c,Rd = 113.74 kN*m Mz,c,Rd = 22.78 kN*m
MN,z,Rd = 22.78 kN*m
Classe de la section = 2
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 5.68 m Lam_y = 0.54 Lz = 5.68 m Lam_z = 2.00
Lcr,y = 5.68 m Xy = 0.91 Lcr,z = 5.68 m Xz = 0.21
Lamy = 50.61 kyz = 0.72 Lamz = 187.93 kzz = 0.98
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd = 0.02 < 1.00 (6.2.4.(1))
Mz,Ed/Mz,c,Rd = 0.05 < 1.00 (6.2.5.(1))
Vy,Ed/Vy,c,Rd = 0.01 < 1.00 (6.2.6.(1))
Contrôle de la stabilité globale de la barre:
Lambda,y = 50.61 < Lambda,max = 210.00 Lambda,z = 187.93 < Lambda,max = 210.00 STABLE
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.06 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.13 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 4 Traverses
PIECE: 52 Poutre_52 POINT: 7 COORDONNEE: x = 1.00 L = 5.96
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /5/ 9*1.08 + 15*1.35 + 18*1.50 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 270

h=27.0 cm gM0=1.00 gM1=1.00
b=13.5 cm Ay=31.46 cm2 Az=22.14 cm2 Ax=45.95 cm2
tw=0.7 cm Iy=5789.78 cm4 Iz=419.87 cm4 Ix=16.02 cm4
tf=1.0 cm Wply=484.00 cm3 Wplz=96.95 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
My,Ed = -17.50 kN*m
My,pl,Rd = 113.74 kN*m
My,c,Rd = 113.74 kN*m Vz,Ed = -5.87 kN
Vz,c,Rd = 300.43 kN
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:

----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
My,Ed/My,c,Rd = 0.15 < 1.00 (6.2.5.(1))
Vz,Ed/Vz,c,Rd = 0.02 < 1.00 (6.2.6.(1))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 5 Pannes
PIECE: 96 POINT: 7 COORDONNEE: x = 1.00 L = 3.86
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /22/ 7*1.80 + 15*1.35 + 18*1.05 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 270

h=27.0 cm gM0=1.00 gM1=1.00
b=13.5 cm Ay=31.46 cm2 Az=22.14 cm2 Ax=45.95 cm2
tw=0.7 cm Iy=5789.78 cm4 Iz=419.87 cm4 Ix=16.02 cm4
tf=1.0 cm Wply=484.00 cm3 Wplz=96.95 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
My,Ed = -16.99 kN*m
My,pl,Rd = 113.74 kN*m
My,c,Rd = 113.74 kN*m Vz,Ed = -8.80 kN
Vz,c,Rd = 300.43 kN
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:

----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
My,Ed/My,c,Rd = 0.15 < 1.00 (6.2.5.(1))
Vz,Ed/Vz,c,Rd = 0.03 < 1.00 (6.2.6.(1))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 6 Grandes lisses
PIECE: 109 POINT: 7 COORDONNEE: x = 1.00 L = 3.86
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /22/ 7*1.80 + 15*1.35 + 18*1.05 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 270

h=27.0 cm gM0=1.00 gM1=1.00
b=13.5 cm Ay=31.46 cm2 Az=22.14 cm2 Ax=45.95 cm2
tw=0.7 cm Iy=5789.78 cm4 Iz=419.87 cm4 Ix=16.02 cm4
tf=1.0 cm Wply=484.00 cm3 Wplz=96.95 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
My,Ed = -22.84 kN*m
My,pl,Rd = 113.74 kN*m
My,c,Rd = 113.74 kN*m Vz,Ed = -11.80 kN
Vz,c,Rd = 300.43 kN
 Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:

----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
My,Ed/My,c,Rd = 0.20 < 1.00 (6.2.5.(1))
Vz,Ed/Vz,c,Rd = 0.04 < 1.00 (6.2.6.(1))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: NF EN 1993-1:2005/NA:2007/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 7 Petites lisses
PIECE: 14 Poutre_14 POINT: 7 COORDONNEE: x = 1.00 L =
10.49 m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 1 ELU /32/ 9*1.80 + 15*1.35 + 16*1.35
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER E24 fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 120

h=12.0 cm gM0=1.00 gM1=1.00
b=6.4 cm Ay=9.10 cm2 Az=6.31 cm2 Ax=13.21 cm2
tw=0.4 cm Iy=317.75 cm4 Iz=27.67 cm4 Ix=1.74 cm4
tf=0.6 cm Wply=60.73 cm3 Wplz=13.58 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 5.76 kN Mz,Ed = 0.07 kN*m Vy,Ed = -0.20 kN
Nc,Rd = 310.44 kN My,Ed,max = 0.03 kN*m Mz,Ed,max = 0.07 kN*m Vy,c,Rd = 123.47 kN
Nb,Rd = 69.18 kN My,c,Rd = 14.27 kN*m Mz,c,Rd = 3.19 kN*m
MN,z,Rd = 3.19 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 0.13 m Lam_y = 0.03 Lz = 1.31 m Lam_z = 1.93
Lcr,y = 0.13 m Xy = 1.00 Lcr,z = 2.63 m Xz = 0.22
Lamy = 2.55 kyz = 0.64 Lamz = 181.37 kzz = 0.87
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd = 0.02 < 1.00 (6.2.4.(1))
Mz,Ed/Mz,c,Rd = 0.02 < 1.00 (6.2.5.(1))
Vy,Ed/Vy,c,Rd = 0.00 < 1.00 (6.2.6.(1))
Contrôle de la stabilité globale de la barre:
Lambda,y = 2.55 < Lambda,max = 210.00 Lambda,z = 181.37 < Lambda,max = 210.00 STABLE
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.03 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.10 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!