Per01020-Elm-26-Mc-Q-008 Rev 0

MEMORIA DE CÁLCULO
“INGENIERÍA, PROCURA Y CONSTRUCCIÓN DE UNIDAD DE

INFRAESTRUCTURA MARINA (UIM), A INSTALARSE EN LA SONDA DE PER1020-ELM-26-MC-Q-008
CAMPECHE, GOLFO DE MÉXICO, UIM-26”
PROY. No.1020
ELABORÓ: J.L.C.C. FECHA: SEP/2020 REV. No. 0 HOJA 1 DE 45
SUBDIRECCIÓN DE PROYECTOS DE EXPLOTACIÓN ESTRATÉGICOS

GERENCIA DE SUPERVISIÓN DE PROYECTOS DE INFRAESTRUCTURA ESTRATÉGICA
GRUPO MULTIDISCIPLINARIO DE SUPERVISIÓN DE DUCTOS MARINOS
No. Contrato: 640859821
MEMORIA DE CÁLCULO DE ATIESADOR DE EMBARQUE DE LA

CURVA DE LLEGADA A INTERCONEXIÓN SUBMARINA.
“OLEOGASODUCTO DE 16”Ø x 3.5 KM APROX. DE ELM-26

HACIA INTERCONEXIÓN SUBMARINA MEDIANTE HOT
TAPPING EN OLEOGASODUCTO DE 20”Ø x 22 KM APROX. DE
TETL-A HACIA TLACAME-A (INCLUYE UN DISPARO
SUBMARINO DE 16”Ø)"
0 SEP/2020 APROBADO PARA CONSTRUCCIÓN J.L.C.C. J.A.U.P. M.N.L.M. R.C.G. S.D.S.M.
REVISÓ VALIDÓ COORDINÓ APROBÓ

REV FECHA DESCRIPCIÓN ELABORÓ
PERMADUCTO PERMADUCTO PERMADUCTO PERMADUCTO
CARSO INFRAESTRUCTURA Y CONSTRUCCIÓN S.A. DE C.V., PERMADUCTO, S.A. DE C.V., PER1020-ELM-26-MC-Q-008
EPESA ESPECIALISTAS EN PETRÓLEO Y ENERGÍA S.A. DE C.V. GRUPO SACMAG.
MEMORIA DE CÁLCULO HOJA 2 DE 45 Rev. 0
ÍNDICE
1.0 ALCANCE DEL ANÁLISIS. ......................................................................................... 3
2.0 DATOS DEL ANÁLISIS. .............................................................................................. 3
2.1 DATOS DE LA CURVA DE EXPANSIÓN DE PROYECTO. ........................................ 3
2.2 DATOS DEL ATIESADOR DE EMBARQUE. .............................................................. 4
3.0 BASES DEL ANÁLISIS................................................................................................ 4
3.1 CARGAS CONSIDERADAS. ....................................................................................... 4
3.2 FACTOR DE CARGA DINÁMICA. ............................................................................... 5
4.0 MODELO. ..................................................................................................................... 6
4.1 MODELO DE CURVA DE EXPANSIÓN. .................................................................... 7
4.2 CABLES PARA IZAJE. ................................................................................................ 9
5.0 CARGAS CONSIDERADAS EN EL ANÁLISIS. .......................................................... 9
6.0 LISTADO DE RESULTADOS DEL ANÁLISIS. .......................................................... 13
7.0 DETALLES DEL ATIESADOR DE EMBARQUE ....................................................... 29
7.1 DETALLES DE ABRAZADERA DE ATIESADOR DE EMBARQUE. ........................ 29
8.0 REVISIÓN DE ABRAZADERA .................................................................................. 30
9.0 REVISIÓN POR PUNZONAMIENTO. ........................................................................ 40
9.1 DETALLES DE LA CORRIDA. .................................................................................. 41
10.0 CONCLUSIONES. ...................................................................................................... 45

1.0 ALCANCE DEL ANÁLISIS.
Esta memoria comprende el análisis de los atiesadores de embarque de la curva de expansión a

instalarse en la interconexión submarina en “Oleogasoducto de 16” Ø x 3.5 km de la plataforma ELM-
26 hacia la interconexión submarina mediante Hot Tapping en oleogasoducto de 20”Ø x 22 Km aprox
de Tetl-A hacia Tlacame-A”.
El objetivo del análisis es conocer el comportamiento estructural de los elementos que conforman los
atiesadores de embarque de la curva de expansión de proyecto y con base en esto definir la sección
del perfil del atiesador (tubo circular “OC”) más adecuada, para cumplir con los esfuerzos y
deflexiones máximas permisibles.
Los atiesadores de embarque de la curva de expansión tienen la función estructural de brindar la

protección adecuada a la curva de expansión y sus accesorios, en la fase de instalación durante las
maniobras de izaje.
Cabe mencionar que los atiesadores de embarque como elementos de apoyo temporal, deberán ser
retirados después de ser instalada la curva de expansión, por lo cual, el diseño deberá incluir las
conexiones necesarias para el retiro funcional de éstos.
2.0 DATOS DEL ANÁLISIS.

2.1 DATOS DE LA CURVA DE EXPANSIÓN DE PROYECTO.
Curva de Expansión interconexión submarina.
Oleogasoducto
Servicio:
(Amargo)
16.00 pulg
Diámetro Exterior:
406.4 mm
0.562 pulg
Espesor de pared de curva de expansión:
14.27 mm
490.06 lb/pie3
Densidad del acero:
7,850 kg/m3
65,000 psi
Esfuerzo de Cedencia Mínimo (SMYS):
4,569.952 kg/cm2
29,500,636.35 psi
(1)Módulo de Elasticidad (E):
2’074,099.999 kg/cm2
2.5 pulg
Espesor de lastre de concreto:
63.5 mm
187.28 lb/ft3
Densidad del lastre de concreto:
3000 kg/m3
-84.842 ft
Tirante de Agua
-25.86 m
Nota:
(1) Estos valores fueron tomados de la Sección 8.1.3.1.1.4 “Espesor por temperatura para ductos
restringidos”, página 30 de 67 de la especificación P.2.0722.03:2015. Este análisis considera la
temperatura cuando el Oleogasoducto se encuentra fuera de operación.
2.2 DATOS DEL ATIESADOR DE EMBARQUE.
Datos del atiesador (Tubo circular “OC”)
12.75 pulg
Diámetro exterior:
323.85 mm
0.50 pulg
Espesor:
12.70 mm
Especificación del acero: A-53 Grado B
29,500,000 psi
Módulo de elasticidad (E):
2’074,048 kg/cm2
75.2 °F
Temperatura ambiente:
24.0°C
3.0 BASES DEL ANÁLISIS.

El análisis de esfuerzos se realizará utilizando el programa “Bentley SACS”; del análisis se obtendrán
las deflexiones, fuerzas y momentos máximos, considerando únicamente las cargas por gravedad
(peso propio de la tubería y lastre de concreto) y que la estructura será izada en los puntos mínimos
necesarios, para tener un comportamiento adecuado durante el izaje.
Normativamente el análisis cumple con lo establecido en el API RP 2A-WSD “Recommended

Practice for Planning, Designing and Constructing Fixed Offshore Platforms-Working Stress Design” y
con el código ASME B31.4 “Pipeline Transportation Systems for Liquid Hydrocarbons and Other
Liquids”.
3.1 CARGAS CONSIDERADAS.
Peso propio y cargas adicionales.
Incluye el peso de los elementos estructurales considerados en el modelo geométrico, así como el de
los elementos no estructurales (abrazaderas, ánodos, lastre de concreto, etc). El peso de todos los
elementos de acero definidos en el modelo estructural, es calculado por el programa de cómputo
SACS, utilizando un peso específico del acero de 7850 kg/m³. Se considera 5% de incremento por
contingencia de acuerdo a la Tabla 15 de la ETP-041, “Carga, Amarre, Transporte e Instalación de
Plataformas Costa Afuera”:
Figura 1. Factores de contingencia indicados en la tabla 15 de la ETP-041, “Carga, Amarre,

Transporte e Instalación de Plataformas Costa Afuera”
3.2 FACTOR DE CARGA DINÁMICA.
Los elementos estructurales y juntas tubulares, se revisan considerando un factor de amplificación

dinámica de 1.3 de acuerdo a lo indicado en la tabla 9 de la ETP-041.
De acuerdo al anexo A.3.2.1 apartado D de la [Ref. 2], todos los izajes están expuestos a efectos
dinámicos debido a variaciones en la velocidad de izaje, movimientos de la grúa de las
embarcaciones, y movimientos de los chalanes, por lo que para tomarse esto en cuenta se afectará
el peso por un Factor de Ampliación Dinámica (FAD):
Figura 2. Factores de ampliación dinámica.
CDG = (PE) FAD.
Dónde:
CDG: Carga dinámica en el Gancho.

PE: Peso de la estructura incluyendo el 5% del factor de contingencia.
Sustituyendo valores en la ecuación:

CDG = 1.05 [PE] FAD
CDG = (1.05) (1.5) = 1.575 PE.
4.0 MODELO.
El análisis de izaje se basa en lo establecido en la norma de referencia ETP-041, “Carga, amarre,
transporte e instalación de plataformas costa afuera”, en el API RP-2A WSD “Recommended practice
for planning, designing and constructing fixed offshore platforms-working stress design” y la
información contenida en los siguientes planos de ingeniería de detalle.
Ingeniería de Detalle
Plano Descripción
Detalles constructivos de curva de expansión,
D-PER1020-ELM-26 -Q-203
Interconexión submarina.
En el modelo de izaje de la curva de expansión se tomaron las siguientes condiciones a las que va a
estar sometida la estructura durante la maniobra de izaje:
• Solo cuenta con un punto de apoyo, el gancho de la grúa.
• Para darle estabilidad al modelo de izaje se consideran dos apoyos elásticos (resortes),
liberando las rotaciones en los tres ejes coordenados y restringiendo parcialmente las
traslaciones en el sentido horizontal, permitiendo así a la estructura tener libertad de
traslación en la dirección vertical. Debido a que su función es únicamente la de hacer estable
el modelo, se les asigna una rigidez lineal de magnitud de (50 kg/m).
• Los cables de izaje a utilizar trabajan únicamente a tensión y no son capaces de absorber
esfuerzos de flexión o compresión. Para representar estas condiciones en el modelo de
análisis de izaje de la curva de expansión, se liberaron las rotaciones de los dos ejes locales
del elemento que trabajan a flexión en un extremo de los cables, quedando restringidas las
traslaciones.
4.1 MODELO DE CURVA DE EXPANSIÓN.
GANCHO DE GRÚA
CODO
PUNTOS DE
DE 90° TUBO DE 16”Ø
IZAJE
PUNTOS DE IZAJE BRIDA SWIVEL
3.11
3.11
7.89
5.89
4.00
ATIESADOR DE
BRIDA W.N. EMBARQUE
5.00
5.00
(VISTA EN ISOMÉTRICO)
CURVA DE EXPANSIÓN, INTERCONEXIÓN SUBMARINA.
4.00 7.89 3.11
PUNTOS DE
IZAJE CODO DE 90° 3.11
BRIDA SWIVEL
ATIESADOR
DE
EMBARQUE
12”Ø
5.89
PUNTOS DE
IZAJE
5.00
TUBERÍA DE 16”Ø
5.00
BRIDA W.N.
VISTA EN PLANTA)
CURVA DE EXPANSIÓN, INTERCONEXIÓN SUBMARINA.
4.2 CABLES PARA IZAJE.
En el modelo de análisis de izaje de la curva de expansión, se modelaron los cables de izaje como un
elemento tubular y Fy=2460 kg/cm².
Para condiciones normales costa afuera, los cables deben ser seleccionados teniendo un factor de
seguridad de 4.0, para la fuerza mínima de ruptura nominal asignada por el fabricante del cable de
acuerdo al API RP 2A-WSD en su sección 2.4.2.f “Slings, Shackles and Fittings”. Por lo tanto, se
deberán seleccionar cables que soporten apropiadamente las tensiones requeridas considerando un
factor de seguridad de 4.0.
5.0 CARGAS CONSIDERADAS EN EL ANÁLISIS.

En el análisis se consideró únicamente la carga debida al peso propio de la tubería, lastre de
concreto, bridas, recubrimiento anticorrosivo y ánodo de sacrificio como se muestra a continuación.
Datos de las cargas por gravedad

187.28 lb/f3
Densidad de Lastre de Concreto.
3,000 kg/m3
490.06 lb/ft3
Densidad de Acero.
7,850 kg/m3
161.00 lb
Peso del Ánodo.
73.03 kg
630 lb
Brida de anillo giratorio (S.R.F.).
285.76 kg
390.21 lb
Brida de cuello soldable (W.N.).
177.00 kg
90.0 lb/ft³
Densidad del recubrimiento anticorrosivo.
1441.66 kg/m³
El análisis contempla las condiciones de carga anteriores con un factor de carga del 5%.
En el análisis, los puntos de izaje y los elementos internos de la estructura, conectados en el nodo
donde el cable transmite las fuerzas de izaje a la estructura, deben ser diseñados con un factor de
carga mínimo de 2.0 aplicado a las cargas estáticas calculadas de acuerdo al API RP 2A-WSD en su
sección 2.4.2.c “Dynamic Load Factors”.
Por lo cual en el presente análisis se considera un factor de amplificación dinámica de 1.5 para todos
los elementos de la curva de expansión y de 2.0 para los atiesadores de embarque.
CARGAS APLICADAS POR PESO PROPIO EN CURVA DE EXPANSIÓN.

CARGAS APLICADAS POR CARGAS DE LASTRE DE CONCRETO EN CURVA DE EXPANSIÓN.

COMBINACIÓN DE CARGAS CDG 1.575 (PP+CM) EN CURVA DE EXPANSIÓN.

6.0 LISTADO DE RESULTADOS DEL ANÁLISIS.

CONTENTS FOR PRE
OPTIONS 1
TUBULAR MEMBER PROPERTIES 2
OPTIMIZATION DATA 3
JOINT DATA LIST 4
SPRING DATA LIST 5
MEMBER DATA REPORT 6
MEMBER SLENDERNESS RATIO REPORT 7
LOAD CASE STATUS REPORT 8
CONTENTS FOR SLV
SACS PROBLEM DESCRIPTION 1

APPLIED LOAD SUMMARY 2
MATRIX DECOMPOSITION DATA 3
REACTION SUMMARY 4
SPRING FORCE SUMMARY 5
CONTENTS FOR PST
SACS MODEL PARAMETERS 1

SACS LOAD CASE REPORT 2
REACTION FORCES AND MOMENTS 4
JOINT DEFLECTIONS AND ROTATIONS 6
MAXIMUM JOINT DEFLECTIONS 9
MEMBER FORCES AND MOMENTS 12
ELEMENT STRESS AT MAX. UNITY CHECK 19
MEMBER INTERNAL LOADS SUMMARY REPORT 21
SACS CONNECT Edition (v11.0) Protexa ID=

DATE 28-JUL-2020 TIME 17:22:06 PRE PAGE 1
PRE VERSION 11.3.0.15
** PROGRAM OPTIONS **
UNITS
....METRIC (KG)
EXECUTION
....UNITY CHECK
WSD AISC 13TH EDITION WITH API-RP2A EDITION FOR TUBULARS
....DKT PLATES SELECTED
....NO SEGMENTS FOR PRISMATIC MEMBERS 1
....NO SEGMENTS/SECTION FOR NON-PRISMATIC MEMBERS 1
REPORTS SELECTED
....INTERPRETIVE INPUT......................PRINT
....JOINT DEFLECTIONS.......................PRINT
....ELEMENT STRESS AT MAXIMUM UNITY CHECK...PRINT
....BEAM COMBINED AND SHEAR UNITY CHECK.....PRINT
....ELEMENT INTERNAL LOADS..................PRINT
....JOINT REACTIONS.........................PRINT
LOAD
....NO. BASIC LOAD COND. 4
....NO. COMB. LOAD COND. 2

TUBULAR MEMBER PROPERTIES
JOINT WALL OUTSIDE E G AXIAL ***** MOMENTS OF INERTIA **** YIELD KY KZ SHEAR RING SECT TAPER
GRP M/S THICK THICK DIAM. 1000 1000 AREA X-X Y-Y Z-Z STRESS AREA SPACE LENG
M CM CM KGSMM KGSMM CM**2 CM**4 CM**4 CM**4 KGSMM CM**2 M M
CAB 1 0.00 1.260 2.54 20.4 7.9 5.0668 4.0864 2.0432 2.0432 24.6 1.0 1.0 2.53 0.00 0.00
T12 1 0.00 1.270 30.48 20.4 7.9 116.54 24906. 12453. 12453. 24.6 1.0 1.0 58.27 0.00 0.00
T16 1 0.00 1.427 40.64 20.4 7.9 175.79 67668. 33834. 33834. 42.2 1.0 1.0 87.90 0.00 0.00

OPTIMIZATION DATA
OPTIMIZED FINAL BANDWIDTH = 3.143 FINAL MAXIMUM BANDWIDTH = 5

* * * J O I N T D A T A L I S T * * *
ORIGINAL JOINT *** TOTAL COORDINATES *** *** TOTAL COORDINATES *** *** FIXITY *** * OPTIMIZED JOINT BEGIN.
JOINT NO. X Y Z X Y Z TRANS ROT * JOINT NO. ROW
ORDER (M) (M) (M) (CM) (CM) (CM) X Y Z X Y Z * ORDER LOC.

*
1 0000 0.00 0.00 0.00 0.00 0.00 0.00 S S S S * 9 0008 1
2 0001 -8.00 0.00 0.00 -800.00 0.00 0.00 * 8 0007 7
3 0002 -10.00 0.00 0.00 -1000.00 0.00 0.00 * 10 0009 13
4 0003 -13.78 0.00 0.00 -1378.10 0.00 0.00 * 7 0006 19
5 0004 -14.08 -0.03 0.00 -1408.04 -2.62 0.00 * 11 0010 25
6 0005 -14.37 -0.10 0.00 -1437.06 -10.40 0.00 * 6 0005 31
7 0006 -14.64 -0.23 0.00 -1464.30 -23.10 0.00 * 12 0011 37
8 0007 -14.89 -0.40 0.00 -1488.91 -40.33 0.00 * 5 0004 43
9 0008 -15.10 -0.62 0.00 -1510.16 -61.58 0.00 * 13 0012 49
10 0009 -15.27 -0.86 0.00 -1527.40 -86.20 0.00 * 4 0003 55
11 0010 -15.40 -1.13 0.00 -1540.10 -113.43 0.00 * 21 0022 61
12 0011 -15.48 -1.42 0.00 -1547.87 -142.46 0.00 * 18 0019 67
13 0012 -15.50 -1.72 0.00 -1550.49 -172.39 0.00 * 3 0002 73
14 0013 -15.50 -5.50 0.00 -1550.49 -550.49 0.00 * 14 0013 79
15 0014 -15.50 -19.50 0.00 -1550.49 -1950.49 0.00 S S S S * 20 0021 85
16 0015 -15.50 -9.50 0.00 -1550.49 -950.49 0.00 * 2 0001 88
17 0016 -15.50 -14.50 0.00 -1550.49 -1450.49 0.00 * 16 0015 94
18 0019 -11.89 0.00 0.00 -1189.05 0.00 0.00 * 19 0020 100
19 0020 -4.00 0.00 0.00 -400.00 0.00 0.00 * 1 0000 106
20 0021 -11.90 -5.50 35.00 -1190.00 -550.00 3500.00 R R R * 17 0016 112
21 0022 -15.50 -3.61 0.00 -1550.49 -361.44 0.00 * 15 0014 118

* * * S P R I N G D A T A L I S T * * *
JOINT ** TRANSLATIONAL SPRINGS ** *** ROTATIONAL SPRINGS *** *** DIRECTION COSINES OF SPRING LOCAL COORDINATES ****
NO. X Y Z X Y Z **** LOCAL X **** **** LOCAL Y **** **** LOCAL Z ****
--------- (MT/CM) --------- ------- (CM-MT/RAD) ------ X Y Z X Y Z X Y Z
0000 0.5000E-030.5000E-03 0.000 0.5001E-010.5001E-01 0.000 1.00 0.00 0.00 0.00 1.00 0.00 0.00 0.00 1.00
0014 0.5000E-030.5000E-03 0.000 0.5001E-010.5001E-01 0.000 1.00 0.00 0.00 0.00 1.00 0.00 0.00 0.00 1.00

* * * M E M B E R D A T A R E P O R T * * *
************* OFFSETS ************* SLENDERNESS

MEMBER JNT JNT GRP MEMBER FIXITY RP CHORD REF OFF JOINT A JOINT B JOINT RATIO FLD DENS. TOTAL
NUMBER A B ID. TRN ROT TRN ROT SK ANGLE JNT OPT X Y Z X Y Z THICK KL/RY KL/RZ LENGTH
XYZ XYZ XYZ XYZ (DEG) (CM) (CM) (CM) (CM) (CM) (CM) (M) MT/M**3 (M)
1 0015-0021 CAB 000 000 000 000 0.00 0.0 5576.65576.6 7.85 35.41
2 0016-0021 CAB 000 000 000 000 0.00 0.0 5719.45719.4 7.85 36.32
3 0020-0021 CAB 000 000 000 000 0.00 0.0 5716.35716.3 7.85 36.30
4 0021-0019 CAB 000 000 000 000 0.00 0.0 5579.35579.3 7.85 35.43
5 0022-0021 CAB 000 000 000 000 0.00 0.0 5548.75548.7 7.85 35.24
6 0013-0002 T12 000 000 000 000 0.00 0.0 75.3 75.3 7.85 7.79
7 0000-0020 T16 000 000 000 000 0.00 0.0 28.8 28.8 7.85 4.00
8 0001-0002 T16 000 000 000 000 0.00 0.0 14.4 14.4 7.85 2.00
9 0002-0019 T16 000 000 000 000 0.00 0.0 13.6 13.6 7.85 1.89
10 0003-0004 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
11 0004-0005 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
12 0005-0006 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
13 0006-0007 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
14 0007-0008 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
15 0008-0009 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
16 0009-0010 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
17 0010-0011 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
18 0011-0012 T16 000 000 000 000 0.00 0.0 2.2 2.2 7.85 0.30
19 0012-0022 T16 000 000 000 000 0.00 0.0 13.6 13.6 7.85 1.89
20 0013-0015 T16 000 000 000 000 0.00 0.0 28.8 28.8 7.85 4.00
21 0015-0016 T16 000 000 000 000 0.00 0.0 36.0 36.0 7.85 5.00
22 0016-0014 T16 000 000 000 000 0.00 0.0 36.0 36.0 7.85 5.00
23 0019-0003 T16 000 000 000 000 0.00 0.0 13.6 13.6 7.85 1.89
24 0020-0001 T16 000 000 000 000 0.00 0.0 28.8 28.8 7.85 4.00
25 0022-0013 T16 000 000 000 000 0.00 0.0 13.6 13.6 7.85 1.89

M E M B E R S L E N D E R N E S S R A T I O R E P O R T
COLUMN AVG.
MEMBER GRP ** FACTORS ** UNBRACED LENGTH EULER BUCKLING SLENDERNESS JOINT ACTUAL
KY KZ LY LZ KLY KLZ RATIO THICK LENGTH
M M M M Y-Y Z-Z M M
0015-0021 CAB 1.000 1.000 35.41 35.41 35.41 35.41 5576.56 5576.56 0.00 35.41
0016-0021 CAB 1.000 1.000 36.32 36.32 36.32 36.32 5719.37 5719.37 0.00 36.32
0020-0021 CAB 1.000 1.000 36.30 36.30 36.30 36.30 5716.28 5716.28 0.00 36.30
0021-0019 CAB 1.000 1.000 35.43 35.43 35.43 35.43 5579.26 5579.26 0.00 35.43
0022-0021 CAB 1.000 1.000 35.24 35.24 35.24 35.24 5548.73 5548.73 0.00 35.24
0013-0002 T12 1.000 1.000 7.79 7.79 7.79 7.79 75.31 75.31 0.00 7.79
0000-0020 T16 1.000 1.000 4.00 4.00 4.00 4.00 28.83 28.83 0.00 4.00
0001-0002 T16 1.000 1.000 2.00 2.00 2.00 2.00 14.42 14.42 0.00 2.00
0002-0019 T16 1.000 1.000 1.89 1.89 1.89 1.89 13.63 13.63 0.00 1.89
0003-0004 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0004-0005 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0005-0006 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0006-0007 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0007-0008 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0008-0009 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0009-0010 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0010-0011 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0011-0012 T16 1.000 1.000 0.30 0.30 0.30 0.30 2.17 2.17 0.00 0.30
0012-0022 T16 1.000 1.000 1.89 1.89 1.89 1.89 13.63 13.63 0.00 1.89
0013-0015 T16 1.000 1.000 4.00 4.00 4.00 4.00 28.83 28.83 0.00 4.00
0015-0016 T16 1.000 1.000 5.00 5.00 5.00 5.00 36.04 36.04 0.00 5.00
0016-0014 T16 1.000 1.000 5.00 5.00 5.00 5.00 36.04 36.04 0.00 5.00
0019-0003 T16 1.000 1.000 1.89 1.89 1.89 1.89 13.63 13.63 0.00 1.89
0020-0001 T16 1.000 1.000 4.00 4.00 4.00 4.00 28.83 28.83 0.00 4.00
0022-0013 T16 1.000 1.000 1.89 1.89 1.89 1.89 13.63 13.63 0.00 1.89

**** LOAD CASE STATUS REPORT ****
LOAD LOAD PRINT DEAD P-DELTA LOAD AMOD

CASE ID OPTION LOAD LOAD FACTOR FACTOR
1 PP YES NO NO 1.00 1.00

2 SW YES NO NO 1.00 1.00
3 WN YES NO NO 1.00 1.00
4 LAST YES NO NO 1.00 1.00
5 CDG YES NO NO 1.00 1.00
6 CEG YES NO NO 1.00 1.00

DATE 28-JUL-2020 TIME 17:22:06 SLV PAGE 1
SLV VERSION 11.3.0.16
** SACS PROBLEM DESCRIPTION **
NUMBER OF JOINTS .......... 21
NUMBER OF BEAMS ........... 25
NUMBER OF PLATES .......... 0
NUMBER OF SHELLS .......... 0
NUMBER OF SOLIDS .......... 0
NUMBER OF LOADS ........... 4
NUMBER OF MASTER JOINTS ... 0
PRINT OPTION .............. 0


APPLIED LOAD SUMMARY
LOAD CASE TOTAL FORCE(X) TOTAL FORCE(Y) TOTAL FORCE(Z)

NO. ID KG KG KG
1 PP 1.148644E-06 4.144107E-07 -6.152589E+03

2 SW 0.000000E+00 0.000000E+00 -2.857601E+02
3 WN 0.000000E+00 0.000000E+00 -1.780000E+02
4 LAST 0.000000E+00 0.000000E+00 -1.016034E+04

MATRIX TRIANGULARIZATION COMPLETE
MAX. SIGNIFICANT DIGITS LOST = 4 SOLUTION ACCURATE TO 11 DIGITS OUT OF POSSIBLE 15
FORWARD SUBSTITUTION COMPLETE
BACK SUBSTITUTION COMPLETE

FIXED DEGREE OF FREEDOM REACTION SUMMARY

NO. ID KG KG KG
1 PP 3.521051E+01 -4.767920E+01 6.152589E+03

2 SW -9.715748E+01 -4.490466E+01 2.857601E+02
3 WN 1.833342E+01 7.122441E+01 1.780000E+02
4 LAST 2.635652E+01 1.669859E+01 1.016034E+04

SPRING FORCE SUMMARY

NO. ID KG KG KG
1 PP 3.521051E+01 -4.767920E+01 0.000000E+00

2 SW -9.715748E+01 -4.490466E+01 0.000000E+00
3 WN 1.833341E+01 7.122441E+01 0.000000E+00
4 LAST 2.635651E+01 1.669859E+01 0.000000E+00

DATE 28-JUL-2020 TIME 17:22:07 PST PAGE 1
PST VERSION 11.3.0.21
******* SACS MODEL PARAMETERS ********
NUMBER OF JOINTS .............. 21
NUMBER OF MEMBERS ............. 25
NUMBER OF PLATES .............. 0
NUMBER OF SHELL ELEMENTS ...... 0
NUMBER OF SOLID ELEMENTS ...... 0
NUMBER OF BASIC LOADS ......... 4
NUMBER OF COMBINED LOADS ...... 2
UNITY CHECK .... WSD AISC 13th / API RP2A-WSD
JOINT DEFLECTION REPORT ...................YES
GROUP SUMMARY REPORT ......................NO
ELEMENT STRESS AT MAXIMUM UC REPORT .......YES

MEMBER INTERNAL LOADS SUMMARY REPORT ......YES
ELEMENT UNITY CHECK REPORT ................NO
ELEMENT DETAIL REPORT .....................NO
MEMBER END FORCES AND MOMENTS REPORT ......YES
JOINT REACTIONS REPORT ....................YES

***** SACS LOAD CASE REPORT *****
LOAD LOAD TYPE PRINT AMOD WATER LC FACTOR LC FACTOR LC FACTOR LC FACTOR LC FACTOR LC FACTOR
NO. CASE OPTION FACTOR DEPTH
M
1 PP BASIC YES 1.000 0.0
2 SW BASIC YES 1.000 0.0
3 WN BASIC YES 1.000 0.0
4 LAST BASIC YES 1.000 0.0
5 CDG COMB YES 1.000 0.0 PP 1.57 SW 1.57 WN 1.57 LAST 1.57
6 CEG COMB YES 1.000 0.0 PP 1.05 SW 1.05 WN 1.05 LAST 1.05

*** SACS POST PROCESSOR COMMENTS ***
** THE USER SHOULD TAKE NOTE OF THE FOLLOWING COMMENTS REGARDING THE SACS POST PROCESSOR OUTPUT **
BEAMS
(1) INTERNAL LOADS FOR MEMBERS ARE PRESENTED IN THE CLASSICAL ENGINEERING SIGN
CONVENTION AS DESCRIBED BY TIMOSHENKO
(2) IF THE AXIAL COMPRESSIVE LOAD ON A MEMBER EXCEEDS THE EULER BUCKLING LOAD, THEN THE
AXIAL UNITY CHECK VALUE FOR THE MEMBER IS AUGMENTED BY 100 TO INDICATE THAT THE
MEMBER HAS BUCKLED
(3) THE MAXIMUM COMBINED UNITY CHECK CAN BE THE MAXIMUM SHEAR UNITY CHECK IF IT IS
GREATER THAN THE MAXIMUM UNITY CHECK DUE TO BENDING AND AXIAL LOAD
(4) THE FOLLOWING ABBREVIATIONS ARE USED TO DESCRIBE THE CRITICAL UNITY CHECK CONDITIONS:
LOCAP - LOCAL CAPACITY AT CONE-CYLINDER JUNCTION

SHEAR - SHEAR
CM+BN - COMPRESSION WITH BENDING
TN+BN - TENSION WITH BENDING
WEB-SH - WEB SHEAR
FLG-SH - FLANGE SHEAR
EULER - EULER BUCKLING
HOOP - CONES: HOOP COMPRESSION OR TENSION
HYDRO - HYDROSTATIC COLLAPSE
TR+SFA - TORSION,SHEAR,FLEXURE AND AXIAL (FOR HSS ONLY)
(5) THE FOLLOWING ABBREVIATIONS ARE USED TO DESCRIBE THE CRITICAL UNITY CHECK CONDITIONS FOR CONCRETE:
COLBUC - COLUMN BUCKLING

CM+BN - COMPRESSION WITH BENDING IN COLUMN ELEMENT
TN+BN - TENSION WITH BENDING IN COLUMN ELEMENT
SHEAR - SHEAR
TORS - TORSION
BEND-Y - PURE BENDING IN BEAM ELEMENT ABOUT LOCAL Y AXIS
REINF - REINFORCEMENT RATIO
(NOTE) WHEN USING THE AISC 13th/14th EDITION (2005/2010 SPECIFICATIONS) CODE CHECK, THE USER SHOULD HAVE THE P-DELTA EFFECT
INCLUDED IN THE ANALYSIS
(6) FOR EARTHQUAKE ANALYSIS WITH 'PRST' OR 'PRSC' OPTION, ONLY THE FORCES AND MOMENTS AT MEMBER ENDS ARE MEANINGFUL.
'JO' STRESS OPTION IS RECOMMENDED.
PLATES
(1) MEMBRANE STRESSES ARE GIVEN AT THE NEUTRAL AXIS OF THE PLATE IN THE LOCAL
COORDINATE SYSTEM OF THE PLATE . ALSO THE PRINCIPAL MEMBRANE STRESS AND
MAXIMUM SHEAR STRESS ARE GIVEN
(2) THE DIRECT STRESSES RESULTING FROM OUT OF PLANE BENDING ARE GIVEN AT THE UPPER
SURFACE OF THE PLATE (POSITIVE LOCAL Z DIRECTION) IN THE LOCAL COORDINATE SYSTEM
OF THE PLATE . ALSO THE PRINCIPAL BENDING STRESS AND MAXIMUM SHEAR STRESS ARE GIVEN
(3) THE MAXIMUM PRINCIPAL STRESS AND MAXIMUM SHEAR STRESS FOR THE COMBINED MEMBRANE
AND BENDING STRESS ARE GIVEN . THE UNITY CHECK VALUE IS BASED ON THESE STRESSES

SACS-IV SYSTEM FIXED JOINTS REACTION FORCES AND MOMENTS
********************* MT ******************** ******************** KG-M *******************

JOINT LOAD FORCE(X) FORCE(Y) FORCE(Z) MOMENT(X) MOMENT(Y) MOMENT(Z)
NUMBER CASE
0021 PP 0.035 -0.048 6.153 0.000 0.000 0.000

SW -0.097 -0.045 0.286 0.000 0.000 0.000
WN 0.018 0.071 0.178 0.000 0.000 0.000
LAST 0.026 0.017 10.160 0.000 0.000 0.000
CDG -0.027 -0.007 26.423 0.000 0.000 0.000
CEG -0.018 -0.005 17.616 0.000 0.000 0.000

SACS-IV SYSTEM FIXED JOINTS REACTION FORCES AND MOMENTS SUMMARY

*** MOMENTS SUMMED ABOUT ORIGIN ***
********************* MT ******************** ******************** KG-M *******************

LOAD FORCE(X) FORCE(Y) FORCE(Z) MOMENT(X) MOMENT(Y) MOMENT(Z)
CASE
PP 0.035 -0.048 6.153 -32170.361 74447.930 761.038
SW -0.097 -0.045 0.286 -0.017 0.033 -0.001
WN 0.018 0.071 0.178 -3471.843 2759.861 -746.734
LAST 0.026 0.017 10.160 -56466.141 121830.133 -53.752
CDG -0.027 -0.007 26.423 -145070.656 313484.750 -62.133
CEG -0.018 -0.005 17.616 -96713.766 208989.828 -41.422

SACS-IV SYSTEM JOINT DEFLECTIONS AND ROTATIONS
**************** CENTIMETERS **************** ****************** RADIANS ******************

JOINT LOAD DEFL(X) DEFL(Y) DEFL(Z) ROT(X) ROT(Y) ROT(Z)
NUMBER CASE
0000 PP 31.8936195 -45.6578674 3.1199341 -0.0134591 -0.0092934 0.0023968

SW -134.9538422 -15.1338034 -48.7859497 -0.0172763 0.0335581 0.0383312
WN 41.6972275 52.4544868 22.4272633 0.0231935 -0.0081093 -0.0243350
LAST 36.9942207 6.6895142 12.3707457 0.0060195 -0.0074962 -0.0135270
CDG -38.3808174 -2.5950816 -17.1171112 -0.0023978 0.0136383 0.0045140
CEG -25.5872059 -1.7300577 -11.4114056 -0.0015985 0.0090922 0.0030093
0001 PP 31.8939819 -47.5786552 -4.4551449 -0.0135085 -0.0095193 0.0025281

SW -134.9538879 -45.7995949 -22.2280617 -0.0172763 0.0327189 0.0383725
WN 41.6972733 71.8900223 15.9397879 0.0231935 -0.0081094 -0.0242133
LAST 36.9948769 17.4474869 6.0187602 0.0060195 -0.0083253 -0.0130654
CDG -38.3792114 -6.3641686 -7.4413381 -0.0024756 0.0106548 0.0057044
CEG -25.5861416 -4.2427740 -4.9608917 -0.0016504 0.0071032 0.0038029
0002 PP 31.8941574 -48.1062317 -6.3404512 -0.0135332 -0.0093348 0.0027653

SW -134.9538727 -53.4811134 -15.6993475 -0.0172763 0.0325811 0.0384483
WN 41.6972847 76.7261047 14.3178930 0.0231935 -0.0081095 -0.0241449
LAST 36.9951973 20.0076942 4.3610792 0.0060195 -0.0082729 -0.0124991
CDG -38.3783913 -7.6443400 -5.2932997 -0.0025145 0.0108106 0.0071969
CEG -25.5855865 -5.0962229 -3.5288668 -0.0016763 0.0072071 0.0047980
0003 PP 31.8938980 -49.2019615 -9.8524380 -0.0137401 -0.0092939 0.0029297

SW -134.9539795 -68.0377274 -3.3973439 -0.0172810 0.0325168 0.0385186
WN 41.6972084 85.8401794 11.2514219 0.0231935 -0.0081105 -0.0240900
LAST 36.9945450 24.6104336 1.1585180 0.0059646 -0.0086791 -0.0120809
CDG -38.3801308 -10.6927891 -1.3227513 -0.0029344 0.0101326 0.0083118
CEG -25.5867462 -7.1285324 -0.8818334 -0.0019562 0.0067551 0.0055412
0004 PP 31.9015388 -49.2895546 -10.0945053 -0.0137582 -0.0092838 0.0029218

SW -134.8531189 -69.1907730 -2.3786824 -0.0172815 0.0325156 0.0385156
WN 41.6341057 86.5613556 10.9478855 0.0231935 -0.0081104 -0.0240921
LAST 36.9628296 24.9723454 0.8830012 0.0059598 -0.0086839 -0.0120995
CDG -38.3585663 -10.9409380 -1.0116252 -0.0029711 0.0101390 0.0082622
CEG -25.5723801 -7.2939491 -0.6744159 -0.0019807 0.0067594 0.0055081
0005 PP 31.9242039 -49.3742294 -10.2567301 -0.0137759 -0.0092720 0.0029120

SW -134.5535736 -70.3086777 -1.3004816 -0.0172820 0.0325146 0.0385116
WN 41.4466972 87.2606964 10.5320740 0.0231935 -0.0081104 -0.0240948
LAST 36.8685684 25.3238640 0.5845911 0.0059542 -0.0086844 -0.0121233
CDG -38.2947044 -11.1798916 -0.6938612 -0.0030085 0.0101554 0.0081986
CEG -25.5298023 -7.4532709 -0.4625742 -0.0020057 0.0067702 0.0054657
0006 PP 31.9610920 -49.4533997 -10.3340273 -0.0137930 -0.0092588 0.0029010

SW -134.0645447 -71.3574829 -0.1954920 -0.0172826 0.0325137 0.0385069
WN 41.1406898 87.9169540 10.0166550 0.0231935 -0.0081103 -0.0240982
LAST 36.7143860 25.6543827 0.2725321 0.0059476 -0.0086816 -0.0121506
CDG -38.1912079 -11.4022770 -0.3785232 -0.0030469 0.0101793 0.0081255
CEG -25.4608002 -7.6015182 -0.2523476 -0.0020313 0.0067862 0.0054170


NUMBER CASE
0007 PP 32.0109711 -49.5246811 -10.3238773 -0.0138097 -0.0092444 0.0028894

SW -133.4008942 -72.3052750 0.9027134 -0.0172833 0.0325131 0.0385017
WN 40.7252960 88.5101776 9.4172592 0.0231935 -0.0081102 -0.0241019
LAST 36.5046539 25.9537888 -0.0435604 0.0059403 -0.0086768 -0.0121797
CDG -38.0519714 -11.6014271 -0.0747592 -0.0030858 0.0102087 0.0080475
CEG -25.3679752 -7.7342863 -0.0498382 -0.0020572 0.0068058 0.0053650
0008 PP 32.0722275 -49.5859756 -10.2265358 -0.0138257 -0.0092290 0.0028780

SW -132.5828400 -73.1233521 1.9608394 -0.0172842 0.0325126 0.0384964
WN 40.2131081 89.0223465 8.7520885 0.0231934 -0.0081101 -0.0241056
LAST 36.2454910 26.2128582 -0.3540137 0.0059326 -0.0086707 -0.0122088
CDG -37.8819351 -11.7717419 0.2084964 -0.0031246 0.0102419 0.0079696
CEG -25.2546177 -7.8478308 0.1389974 -0.0020830 0.0068279 0.0053131
0009 PP 32.1429253 -49.6355057 -10.0449562 -0.0138411 -0.0092126 0.0028675

SW -131.6353302 -73.7868423 2.9466858 -0.0172852 0.0325122 0.0384914
WN 39.6196976 89.4378586 8.0413980 0.0231934 -0.0081100 -0.0241092
LAST 35.9445915 26.4234753 -0.6493460 0.0059253 -0.0086642 -0.0122360
CDG -37.6867561 -11.9085989 0.4627071 -0.0031620 0.0102776 0.0078966
CEG -25.1245155 -7.9390683 0.3084716 -0.0021080 0.0068517 0.0052644
0010 PP 32.2208862 -49.6718903 -9.7846832 -0.0138557 -0.0091953 0.0028585

SW -130.5870819 -74.2756653 3.8303678 -0.0172864 0.0325120 0.0384870
WN 38.9630356 89.7440567 7.3067303 0.0231934 -0.0081098 -0.0241124
LAST 35.6109886 26.5789719 -0.9206271 0.0059191 -0.0086578 -0.0122596
CDG -37.4726753 -12.0086222 0.6800670 -0.0031966 0.0103147 0.0078333
CEG -24.9817772 -8.0057526 0.4533770 -0.0021311 0.0068765 0.0052222
0011 PP 32.3037491 -49.6941147 -9.4537477 -0.0138694 -0.0091774 0.0028517

SW -129.4700165 -74.5749664 4.5849829 -0.0172877 0.0325119 0.0384834
WN 38.2631111 89.9315872 6.5704517 0.0231933 -0.0081097 -0.0241150
LAST 35.2548447 26.6743355 -1.1596748 0.0059150 -0.0086517 -0.0122779
CDG -37.2460861 -12.0694666 0.8536688 -0.0032268 0.0103527 0.0077840
CEG -24.8307285 -8.0463123 0.5691128 -0.0021512 0.0069018 0.0051893
0012 PP 32.3890457 -49.7015953 -9.0623732 -0.0138819 -0.0091587 0.0028476

SW -128.3180084 -74.6757660 5.1876817 -0.0172893 0.0325119 0.0384810
WN 37.5411720 89.9947433 5.8548994 0.0231932 -0.0081095 -0.0241168
LAST 34.8870964 26.7064629 -1.3593748 0.0059141 -0.0086460 -0.0122895
CDG -37.0135918 -12.0899496 0.9778115 -0.0032506 0.0103914 0.0077528
CEG -24.6757202 -8.0599594 0.6518748 -0.0021670 0.0069276 0.0051685
0013 PP 33.4933968 -49.7017632 -3.8072960 -0.0139415 -0.0089374 0.0030976

SW -113.7582016 -74.6758728 11.7305717 -0.0173197 0.0325129 0.0385717
WN 28.4293709 89.9946518 -2.9149411 0.0232049 -0.0081074 -0.0240557
LAST 30.3048306 26.7059708 -3.6539254 0.0062536 -0.0085765 -0.0117071
CDG -33.9107018 -12.0912867 2.1331947 -0.0028393 0.0108543 0.0093029
CEG -22.6071262 -8.0608635 1.4221293 -0.0018929 0.0072362 0.0062019


NUMBER CASE
0014 PP 38.5275650 -49.7007561 14.9477797 -0.0127020 -0.0088248 0.0036736

SW -59.3615685 -74.6757202 36.0045815 -0.0173414 0.0325128 0.0389956
WN -5.0303154 89.9946671 -35.9665070 0.0240912 -0.0081074 -0.0238508
LAST 15.7189322 26.7077446 -14.5210447 0.0093187 -0.0085765 -0.0101099
CDG -15.9789782 -12.0866604 0.7320691 0.0053022 0.0110317 0.0137159
CEG -10.6526556 -8.0577793 0.4880489 0.0035348 0.0073544 0.0091439
0015 PP 34.8454018 -49.7012634 1.7802306 -0.0138675 -0.0088683 0.0035848

SW -98.2853928 -74.6758270 18.6634998 -0.0173394 0.0325129 0.0387802
WN 18.8356133 89.9946823 -12.2174139 0.0233288 -0.0081074 -0.0239234
LAST 25.8889523 26.7068672 -6.2250919 0.0067636 -0.0085765 -0.0105276
CDG -29.4767952 -12.0889807 3.1519291 -0.0017554 0.0109631 0.0124647
CEG -19.6511936 -8.0593204 2.1012869 -0.0011703 0.0073087 0.0083098
0016 PP 36.6849289 -49.7007904 8.5446806 -0.0131188 -0.0088248 0.0037085

SW -78.8503876 -74.6757736 27.3338776 -0.0173414 0.0325129 0.0389418
WN 6.8958402 89.9947205 -23.9746780 0.0237687 -0.0081074 -0.0238554
LAST 20.7715130 26.7077599 -9.9736042 0.0084234 -0.0085765 -0.0100957
CDG -22.8345222 -12.0866747 3.0401838 0.0027276 0.0110317 0.0137014
CEG -15.2230158 -8.0577822 2.0267892 0.0018184 0.0073544 0.0091343
0019 PP 31.8940258 -48.6471634 -8.0944061 -0.0136253 -0.0092755 0.0029233

SW -134.9539185 -60.7560272 -9.5457516 -0.0172787 0.0325301 0.0385073
WN 41.6972466 81.2857285 12.7847033 0.0231935 -0.0081103 -0.0240987
LAST 36.9948692 22.3274937 2.7852259 0.0059920 -0.0084672 -0.0121150
CDG -38.3792496 -9.1191902 -3.2606099 -0.0027065 0.0105164 0.0082167
CEG -25.5861683 -6.0794663 -2.1737404 -0.0018043 0.0070109 0.0054778
0020 PP 31.8936386 -46.6130562 -0.6187522 -0.0134591 -0.0095068 0.0023703

SW -134.9539185 -30.4651165 -35.4068718 -0.0172763 0.0332268 0.0383224

WN 41.6972504 62.1844215 19.1835327 0.0231935 -0.0081093 -0.0243046
LAST 36.9942398 12.0997877 9.3264303 0.0060195 -0.0079546 -0.0135231
CDG -38.3808327 -4.4004898 -11.8371696 -0.0023978 0.0120583 0.0045125
CEG -25.5872211 -2.9336603 -7.8914461 -0.0015985 0.0080389 0.0030083
0021 PP 0.0000000 0.0000000 0.0000000 -0.0042401 -0.1525378 0.0042823

SW 0.0000000 0.0000000 0.0000000 -0.0173906 0.0324339 0.0385283
WN 0.0000000 0.0000000 0.0000000 0.0231876 -0.0081351 -0.0240212
LAST 0.0000000 0.0000000 0.0000000 0.0062985 -0.0087909 -0.0116138
CDG 0.0000000 0.0000000 0.0000000 0.0123722 -0.2158221 0.0113016
CEG 0.0000000 0.0000000 0.0000000 0.0082482 -0.1438814 0.0075344
0022 PP 32.9298477 -49.7016907 -6.4346890 -0.0138914 -0.0090400 0.0028949

SW -121.0424042 -74.6758194 8.4575281 -0.0173047 0.0325124 0.0384986
WN 32.9823608 89.9947052 1.4703048 0.0231922 -0.0081084 -0.0241053
LAST 32.5691299 26.7061939 -2.4861591 0.0060610 -0.0086112 -0.0121797
CDG -35.5336647 -12.0906715 1.5860025 -0.0030600 0.0106355 0.0080459
CEG -23.6891117 -8.0604343 1.0573343 -0.0020400 0.0070904 0.0053639

***************** MAXIMUM JOINT DEFLECTION REPORT *****************
LOAD *** X-DIRECTION *** *** Y-DIRECTION *** *** Z-DIRECTION ***
CASE JOINT DEFLECTION JOINT DEFLECTION JOINT DEFLECTION
CM CM CM
PP 0014 38.5275 0013 -49.7016 0014 14.9477

SW 0003 -134.9537 0013 -74.6757 0000 -48.7858
WN 0002 41.6972 0012 89.9945 0014 -35.9664
LAST 0002 36.9951 0016 26.7077 0014 -14.5210
CDG 0020 -38.3807 0013 -12.0913 0000 -17.1171
CEG 0020 -25.5872 0013 -8.0608 0000 -11.4114

SACS-IV SYSTEM SPRING FORCES AND MOMENTS
LOAD COORD. ************* FORCES ************* ************ MOMENTS *************

JOINT CASE SYS. X Y Z X Y Z
(KG) (KG) (KG) (KG-M) (KG-M) (KG-M)
0000 PP GLOB 15.947 -22.829 0.000 -0.007 -0.005 0.000

SW GLOB -67.477 -7.567 0.000 -0.009 0.017 0.000
WN GLOB 20.849 26.227 0.000 0.012 -0.004 0.000
LAST GLOB 18.497 3.345 0.000 0.003 -0.004 0.000
CDG GLOB -19.190 -1.298 0.000 -0.001 0.007 0.000
CEG GLOB -12.794 -0.865 0.000 -0.001 0.005 0.000
0014 PP GLOB 19.264 -24.850 0.000 -0.006 -0.004 0.000

SW GLOB -29.681 -37.338 0.000 -0.009 0.016 0.000
WN GLOB -2.515 44.997 0.000 0.012 -0.004 0.000
LAST GLOB 7.859 13.354 0.000 0.005 -0.004 0.000
CDG GLOB -7.989 -6.043 0.000 0.003 0.006 0.000
CEG GLOB -5.326 -4.029 0.000 0.002 0.004 0.000

SACS-IV SYSTEM SPRING FORCES AND MOMENTS SUMMARY
LOAD COORD. ************* FORCES ************* ************ MOMENTS *************

CASE SYS. X Y Z X Y Z
(KG) (KG) (KG) (KG-M) (KG-M) (KG-M)
PP GLOB 35.211 -47.679 0.000
SW GLOB -97.157 -44.905 0.000
WN GLOB 18.333 71.224 0.000
LAST GLOB 26.357 16.699 0.000
CDG GLOB -27.180 -7.341 0.000
CEG GLOB -18.120 -4.894 0.000

SACS-IV SYSTEM MEMBER FORCES AND MOMENTS
******************** MT ********************* ******************* MT-CM *******************

MEMBER MEMBER GROUP LOAD FORCE(X) FORCE(Y) FORCE(Z) MOMENT(X) MOMENT(Y) MOMENT(Z)
NUMBER END ID CASE
0015-0021 0015 CAB PP 0.85 0.00 0.01 -0.01 -6.57 -0.23

SW 0.01 0.00 0.00 0.00 0.00 0.00
WN -0.06 0.00 0.00 0.00 0.00 0.00
LAST 1.45 0.00 0.00 0.00 0.00 0.00
CDG 3.54 0.00 0.02 -0.02 -10.34 -0.36
CEG 2.36 0.00 0.01 -0.02 -6.89 -0.24
0021 PP 0.99 0.00 -0.01 -0.01 -5.84 0.46
SW 0.01 0.00 0.00 0.00 0.00 0.00
WN -0.06 0.00 0.00 0.00 0.00 0.00
LAST 1.45 0.00 0.00 0.00 0.00 0.00

CDG 3.76 0.00 -0.02 -0.02 -9.20 0.73
CEG 2.51 0.00 -0.01 -0.02 -6.13 0.49
0016-0021 0016 CAB PP 1.20 0.00 0.02 -0.03 -11.82 -0.28

SW 0.00 0.00 0.00 0.00 0.00 0.00
WN 0.30 0.00 0.00 0.00 0.00 0.00
LAST 2.64 0.00 0.00 0.00 -0.01 0.00
CDG 6.53 0.00 0.03 -0.05 -18.63 -0.44
CEG 4.35 0.00 0.02 -0.03 -12.42 -0.29
0021 PP 1.34 0.00 -0.02 -0.03 -11.39 0.57
SW 0.00 0.00 0.00 0.00 0.00 0.00
WN 0.30 0.00 0.00 0.00 0.00 0.00
LAST 2.64 0.00 0.00 0.00 0.00 0.00
CDG 6.75 0.00 -0.03 -0.05 -17.93 0.89
CEG 4.50 0.00 -0.02 -0.03 -11.95 0.60
0020-0021 0020 CAB PP 1.28 0.00 0.02 0.02 -11.30 0.16

SW 0.43 0.00 0.00 0.00 0.00 0.00
WN 0.00 0.00 0.00 0.00 0.00 0.00
LAST 2.54 0.00 0.00 0.00 0.00 0.00
CDG 6.70 0.00 0.03 0.03 -17.81 0.25
CEG 4.47 0.00 0.02 0.02 -11.87 0.17
0021 PP 1.42 0.00 -0.02 0.02 -12.14 -0.32
SW 0.43 0.00 0.00 0.00 0.00 0.00
WN 0.00 0.00 0.00 0.00 0.00 0.00
LAST 2.54 0.00 0.00 0.00 0.00 0.00
CDG 6.92 0.00 -0.03 0.03 -19.12 -0.51
CEG 4.61 0.00 -0.02 0.02 -12.75 -0.34
0021-0019 0021 CAB PP 1.39 0.00 0.01 0.02 -6.51 0.66

SW -0.11 0.00 0.00 0.00 0.00 0.00
WN 0.00 0.00 0.00 0.00 0.00 0.00
LAST 2.11 0.00 0.00 0.00 0.00 0.00
CDG 5.34 0.00 0.02 0.03 -10.25 1.04
CEG 3.56 0.00 0.01 0.02 -6.83 0.70
0019 PP 1.25 0.00 -0.01 0.02 -6.43 -0.33
SW -0.11 0.00 0.00 0.00 0.00 0.00
WN 0.00 0.00 0.00 0.00 0.00 0.00
LAST 2.11 0.00 0.00 0.00 0.00 0.00
CDG 5.12 0.00 -0.02 0.03 -10.13 -0.52
CEG 3.42 0.00 -0.01 0.02 -6.75 -0.35

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0022-0021 0022 CAB PP 0.99 0.00 0.01 0.01 -5.04 0.17

SW -0.04 0.00 0.00 0.00 0.00 0.00
WN -0.06 0.00 0.00 0.00 0.00 0.00
LAST 1.66 0.00 0.00 0.00 0.00 0.00
CDG 4.03 0.00 0.01 0.02 -7.94 0.27
CEG 2.69 0.00 0.01 0.01 -5.29 0.18
0021 PP 1.13 0.00 -0.01 0.01 -4.17 -0.35
SW -0.04 0.00 0.00 0.00 0.00 0.00
WN -0.06 0.00 0.00 0.00 0.00 0.00
LAST 1.66 0.00 0.00 0.00 0.00 0.00
CDG 4.25 0.00 -0.01 0.02 -6.57 -0.55
CEG 2.84 0.00 -0.01 0.01 -4.38 -0.37
0013-0002 0013 T12 PP -0.80 0.01 0.36 0.19 -27.69 -16.65

SW -0.20 0.00 -0.01 1.99 1.79 -5.54
WN -0.14 0.00 0.00 -0.24 -0.66 -3.34
LAST -1.71 0.03 0.00 1.24 -12.61 -37.08
CDG -4.48 0.08 0.55 5.01 -61.70 -98.61
CEG -2.99 0.05 0.37 3.34 -41.13 -65.74
0002 PP -0.80 0.01 -0.36 0.19 -27.56 -5.03
SW -0.20 0.00 -0.01 1.99 -2.94 -2.51
WN -0.14 0.00 0.00 -0.24 0.24 -2.49
LAST -1.71 0.03 0.00 1.24 -12.18 -14.58
CDG -4.48 0.08 -0.57 5.01 -66.85 -38.75
CEG -2.99 0.05 -0.38 3.34 -44.56 -25.83
0000-0020 0000 T16 PP -0.02 -0.02 0.00 0.00 0.00 0.00

SW 0.07 -0.01 -0.29 0.00 0.00 0.00
WN -0.02 0.03 0.00 0.00 0.00 0.00
LAST -0.02 0.00 0.00 0.00 0.00 0.00
CDG 0.02 0.00 -0.45 0.00 0.00 0.00
CEG 0.01 0.00 -0.30 0.00 0.00 0.00
0020 PP -0.02 -0.02 -0.55 0.00 -110.40 -9.13
SW 0.07 -0.01 -0.29 0.00 -114.28 -3.03
WN -0.02 0.03 0.00 0.00 0.00 10.49
LAST -0.02 0.00 -1.19 0.00 -237.17 1.34
CDG 0.02 0.00 -3.19 0.00 -727.42 -0.52
CEG 0.01 0.00 -2.13 0.00 -484.95 -0.35
0001-0002 0001 T16 PP -0.31 0.18 0.13 6.58 60.09 63.60

SW -0.03 0.06 0.13 0.00 -60.87 20.30
WN -0.02 0.03 0.00 0.00 -0.03 20.97
LAST -0.57 0.39 0.08 0.00 30.26 156.51
CDG -1.46 1.03 0.53 10.36 46.39 411.67
CEG -0.98 0.69 0.35 6.91 30.93 274.45
0002 PP -0.31 0.18 -0.15 6.58 57.94 100.00

SW -0.03 0.06 0.13 0.00 -34.16 31.96
WN -0.02 0.03 0.00 0.00 -0.05 26.22
LAST -0.57 0.39 -0.52 0.00 -13.90 234.09
CDG -1.46 1.03 -0.84 10.36 15.49 617.82
CEG -0.98 0.69 -0.56 6.91 10.33 411.88

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0002-0019 0002 T16 PP 0.25 -0.39 -0.50 25.93 77.57 94.97

SW 0.11 -0.08 0.13 0.67 -30.68 29.45
WN 0.08 -0.07 0.00 0.00 -0.39 23.73
LAST 0.62 -0.84 -0.52 7.74 -4.41 219.51
CDG 1.65 -2.19 -1.41 54.09 66.30 579.07
CEG 1.10 -1.46 -0.94 36.06 44.20 386.05
0019 PP 0.25 -0.39 -0.77 25.93 -42.49 20.34
SW 0.11 -0.08 0.13 0.67 -6.59 13.63
WN 0.08 -0.07 0.00 0.00 -0.18 10.01
LAST 0.62 -0.84 -1.08 7.74 -155.07 60.80
CDG 1.65 -2.19 -2.70 54.09 -321.81 165.05
CEG 1.10 -1.46 -1.80 36.06 -214.54 110.03
0003-0004 0003 T16 PP 0.26 -0.17 0.21 30.40 23.87 -15.61

SW 0.12 -0.09 0.02 0.94 -3.00 -5.42
WN 0.08 -0.07 0.00 -0.01 0.07 -3.69
LAST 0.66 -0.46 0.45 9.21 -16.44 -35.91
CDG 1.76 -1.23 1.07 63.85 7.09 -95.50
CEG 1.17 -0.82 0.71 42.57 4.73 -63.66
0004 PP 0.26 -0.17 0.17 30.40 29.49 -20.65
SW 0.12 -0.09 0.02 0.94 -2.44 -8.15
WN 0.08 -0.07 0.00 -0.01 0.11 -5.67
LAST 0.66 -0.46 0.36 9.21 -4.28 -49.61
CDG 1.76 -1.23 0.86 63.85 36.03 -132.42
CEG 1.17 -0.82 0.57 42.57 24.02 -88.28
0004-0005 0004 T16 PP 0.29 -0.12 0.17 24.82 34.32 -20.65

SW 0.13 -0.07 0.02 1.35 -2.24 -8.15
WN 0.09 -0.05 0.00 -0.02 0.11 -5.67
LAST 0.73 -0.33 0.36 9.81 -2.62 -49.61
CDG 1.95 -0.90 0.86 56.62 46.57 -132.42
CEG 1.30 -0.60 0.57 37.75 31.05 -88.28
0005 PP 0.29 -0.12 0.12 24.82 38.70 -24.24
SW 0.13 -0.07 0.02 1.35 -1.68 -10.23
WN 0.09 -0.05 0.00 -0.02 0.15 -7.18
LAST 0.73 -0.33 0.27 9.81 6.86 -59.68
CDG 1.95 -0.90 0.65 56.62 69.33 -159.59
CEG 1.30 -0.60 0.44 37.75 46.22 -106.39
0005-0006 0005 T16 PP 0.30 -0.07 0.12 17.72 42.42 -24.24

SW 0.14 -0.05 0.02 1.62 -1.42 -10.23
WN 0.10 -0.03 0.00 -0.05 0.14 -7.18
LAST 0.77 -0.20 0.27 8.47 8.46 -59.68
CDG 2.08 -0.55 0.65 43.73 78.11 -159.59
CEG 1.38 -0.37 0.44 29.15 52.07 -106.39
0006 PP 0.30 -0.07 0.08 17.72 45.54 -26.29
SW 0.14 -0.05 0.02 1.62 -0.86 -11.58
WN 0.10 -0.03 0.00 -0.05 0.18 -8.18
LAST 0.77 -0.20 0.18 8.47 15.26 -65.80
CDG 2.08 -0.55 0.45 43.73 94.70 -176.17
CEG 1.38 -0.37 0.30 29.15 63.13 -117.45

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0006-0007 0006 T16 PP 0.31 -0.01 0.08 9.54 47.93 -26.29

SW 0.15 -0.02 0.02 1.74 -0.57 -11.58
WN 0.10 -0.02 0.00 -0.08 0.17 -8.18
LAST 0.80 -0.07 0.18 5.69 16.50 -65.80
CDG 2.14 -0.18 0.45 26.61 100.85 -176.17
CEG 1.43 -0.12 0.30 17.74 67.23 -117.45
0007 PP 0.31 -0.01 0.04 9.54 49.81 -26.73
SW 0.15 -0.02 0.02 1.74 -0.01 -12.18
WN 0.10 -0.02 0.00 -0.08 0.21 -8.65
LAST 0.80 -0.07 0.09 5.69 20.63 -67.79
CDG 2.14 -0.18 0.24 26.61 111.26 -181.67
CEG 1.43 -0.12 0.16 17.74 74.17 -121.11
0007-0008 0007 T16 PP 0.31 0.04 0.04 0.75 50.71 -26.73

SW 0.15 0.01 0.02 1.72 0.29 -12.18
WN 0.11 0.00 0.00 -0.12 0.19 -8.65
LAST 0.80 0.07 0.09 2.02 21.31 -67.79
CDG 2.14 0.19 0.24 6.89 114.19 -181.67
CEG 1.43 0.13 0.16 4.59 76.12 -121.11
0008 PP 0.31 0.04 0.00 0.75 51.34 -25.54

SW 0.15 0.01 0.02 1.72 0.85 -12.00
WN 0.11 0.00 0.00 -0.12 0.23 -8.57
LAST 0.80 0.07 0.00 2.02 22.76 -65.59
CDG 2.14 0.19 0.04 6.89 118.41 -175.92
CEG 1.43 0.13 0.03 4.59 78.94 -117.28
0008-0009 0008 T16 PP 0.30 0.09 0.00 -8.18 50.69 -25.54

SW 0.15 0.03 0.02 1.54 1.14 -12.00
WN 0.10 0.02 0.00 -0.15 0.21 -8.57
LAST 0.77 0.21 0.00 -1.96 22.76 -65.59
CDG 2.07 0.56 0.04 -13.77 117.81 -175.92
CEG 1.38 0.37 0.03 -9.18 78.54 -117.28
0009 PP 0.30 0.09 -0.04 -8.18 50.08 -22.77
SW 0.15 0.03 0.02 1.54 1.69 -11.04
WN 0.10 0.02 0.00 -0.15 0.25 -7.94
LAST 0.77 0.21 -0.09 -1.96 21.53 -59.26
CDG 2.07 0.56 -0.17 -13.77 115.86 -159.09
CEG 1.38 0.37 -0.11 -9.18 77.24 -106.06
0009-0010 0009 T16 PP 0.28 0.14 -0.04 -16.75 47.90 -22.77

SW 0.14 0.06 0.02 1.23 1.94 -11.04
WN 0.10 0.04 0.00 -0.19 0.22 -7.94
LAST 0.72 0.34 -0.09 -5.67 20.87 -59.26
CDG 1.95 0.91 -0.17 -33.68 111.70 -159.09
CEG 1.30 0.61 -0.11 -22.46 74.47 -106.06
0010 PP 0.28 0.14 -0.08 -16.75 46.04 -18.49
SW 0.14 0.06 0.02 1.23 2.50 -9.35
WN 0.10 0.04 0.00 -0.19 0.26 -6.78
LAST 0.72 0.34 -0.17 -5.67 16.96 -49.01
CDG 1.95 0.91 -0.37 -33.68 103.57 -131.70
CEG 1.30 0.61 -0.25 -22.46 69.05 -87.80

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0010-0011 0010 T16 PP 0.25 0.19 -0.08 -24.49 42.43 -18.49

SW 0.13 0.08 0.02 0.77 2.67 -9.35
WN 0.09 0.06 0.00 -0.24 0.22 -6.78
LAST 0.65 0.46 -0.17 -8.53 15.72 -49.01
CDG 1.76 1.24 -0.37 -51.16 96.15 -131.70
CEG 1.17 0.82 -0.25 -34.11 64.10 -87.80
0011 PP 0.25 0.19 -0.12 -24.49 39.33 -12.83
SW 0.13 0.08 0.02 0.77 3.23 -6.96
WN 0.09 0.06 0.00 -0.24 0.26 -5.12
LAST 0.65 0.46 -0.26 -8.53 9.14 -35.13
CDG 1.76 1.24 -0.58 -51.16 81.84 -94.57
CEG 1.17 0.82 -0.39 -34.11 54.56 -63.05
0011-0012 0011 T16 PP 0.21 0.23 -0.12 -30.95 34.48 -12.83

SW 0.11 0.10 0.02 0.20 3.32 -6.96
WN 0.08 0.07 0.00 -0.28 0.22 -5.12
LAST 0.56 0.57 -0.26 -9.98 7.52 -35.13
CDG 1.52 1.52 -0.58 -64.59 71.71 -94.57
CEG 1.01 1.01 -0.39 -43.06 47.81 -63.05
0012 PP 0.21 0.23 -0.17 -30.95 30.13 -5.98
SW 0.11 0.10 0.02 0.20 3.87 -3.95
WN 0.08 0.07 0.00 -0.28 0.26 -3.03
LAST 0.56 0.57 -0.35 -9.98 -1.74 -18.06
CDG 1.52 1.52 -0.78 -64.59 51.22 -48.84
CEG 1.01 1.01 -0.52 -43.06 34.15 -32.56
0012-0022 0012 T16 PP 0.19 0.25 -0.17 -33.46 27.32 -5.98

SW 0.10 0.11 0.02 -0.14 3.88 -3.95
WN 0.07 0.08 0.00 -0.30 0.23 -3.03
LAST 0.51 0.62 -0.35 -9.79 -2.60 -18.06
CDG 1.38 1.65 -0.78 -68.81 45.39 -48.84
CEG 0.92 1.10 -0.52 -45.87 30.26 -32.56
0022 PP 0.19 0.25 -0.43 -33.46 -28.64 40.47
SW 0.10 0.11 0.02 -0.14 7.39 16.73
WN 0.07 0.08 0.00 -0.30 0.48 11.42
LAST 0.51 0.62 -0.91 -9.79 -122.25 98.22
CDG 1.38 1.65 -2.08 -68.81 -225.23 262.76
CEG 0.92 1.10 -1.39 -45.87 -150.16 175.17
0013-0015 0013 T16 PP -0.44 -0.20 -0.06 -9.20 35.38 124.16

SW -0.04 -0.03 -0.01 0.00 6.23 42.19
WN -0.02 -0.03 -0.06 0.00 -10.35 28.12
LAST -0.80 -0.40 0.18 0.00 -44.01 283.70
CDG -2.07 -1.04 0.08 -14.49 -20.08 753.12
CEG -1.38 -0.69 0.05 -9.66 -13.38 502.08
0015 PP -0.44 -0.20 -0.61 -9.20 -97.72 43.84
SW -0.04 -0.03 -0.01 0.00 0.55 29.73
WN -0.02 -0.03 -0.06 0.00 -32.38 17.51
LAST -0.80 -0.40 -1.01 0.00 -210.93 123.09
CDG -2.07 -1.04 -2.66 -14.49 -536.25 337.31
CEG -1.38 -0.69 -1.77 -9.66 -357.50 224.87

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0015-0016 0015 T16 PP -0.34 -0.11 0.23 -4.64 -102.45 43.89

SW -0.04 -0.03 0.00 0.00 0.55 29.73
WN -0.03 -0.03 -0.11 0.00 -32.38 17.51
LAST -0.64 -0.25 0.42 0.00 -210.93 123.09
CDG -1.65 -0.67 0.84 -7.30 -543.70 337.39
CEG -1.10 -0.44 0.56 -4.87 -362.47 224.93
0016 PP -0.34 -0.11 -0.46 -4.64 -161.63 -9.73
SW -0.04 -0.03 0.00 0.00 0.00 14.84
WN -0.03 -0.03 -0.11 0.00 -88.98 1.26
LAST -0.64 -0.25 -1.06 0.00 -370.56 -3.93
CDG -1.65 -0.67 -2.58 -7.30 -978.35 3.83
CEG -1.10 -0.44 -1.72 -4.87 -652.23 2.55
0016-0014 0016 T16 PP -0.02 0.02 0.69 0.00 -172.51 -9.63

SW -0.04 -0.03 0.00 0.00 0.00 14.84
WN 0.04 0.00 0.18 0.00 -88.98 1.26
LAST 0.01 0.01 1.48 0.00 -370.57 -3.93
CDG -0.01 -0.01 3.70 0.00 -995.50 3.99
CEG 0.00 -0.01 2.47 0.00 -663.67 2.66
0014 PP -0.02 0.02 0.00 0.00 0.00 0.00
SW -0.04 -0.03 0.00 0.00 0.00 0.00
WN 0.04 0.00 0.18 0.00 0.00 0.00
LAST 0.01 0.01 0.00 0.00 0.00 0.00
CDG -0.01 -0.01 0.28 0.00 0.00 0.00
CEG 0.00 -0.01 0.19 0.00 0.00 0.00
0019-0003 0019 T16 PP 0.25 -0.19 0.47 32.36 -42.80 20.27

SW 0.11 -0.10 0.02 0.67 -6.59 13.63
WN 0.08 -0.07 0.00 0.00 -0.18 10.01
LAST 0.62 -0.51 1.01 7.74 -155.07 60.80
CDG 1.65 -1.38 2.36 64.22 -322.30 164.93
CEG 1.10 -0.92 1.57 42.82 -214.87 109.96
0003 PP 0.25 -0.19 0.21 32.36 21.13 -15.61

SW 0.11 -0.10 0.02 0.67 -3.07 -5.42
WN 0.08 -0.07 0.00 0.00 0.07 -3.69
LAST 0.62 -0.51 0.45 7.74 -17.18 -35.91
CDG 1.65 -1.38 1.07 64.22 1.50 -95.50
CEG 1.10 -0.92 0.71 42.82 1.00 -63.66
0020-0001 0020 T16 PP -0.31 0.18 0.68 6.58 -101.22 -9.19

SW -0.03 0.06 0.13 0.00 -114.28 -3.03
WN -0.02 0.03 0.00 0.00 0.00 10.49
LAST -0.57 0.39 1.26 0.00 -237.16 1.34
CDG -1.46 1.03 3.27 10.36 -712.94 -0.62
CEG -0.98 0.69 2.18 6.91 -475.29 -0.41
0001 PP -0.31 0.18 0.13 6.58 60.09 63.60
SW -0.03 0.06 0.13 0.00 -60.87 20.30
WN -0.02 0.03 0.00 0.00 -0.03 20.97
LAST -0.57 0.39 0.08 0.00 30.26 156.51
CDG -1.46 1.03 0.53 10.36 46.39 411.67
CEG -0.98 0.69 0.35 6.91 30.93 274.45

******************** MT ********************* ******************* MT-CM *******************

NUMBER END ID CASE
0022-0013 0022 T16 PP 0.13 0.35 0.56 -28.91 -26.45 40.44

SW 0.10 0.11 -0.02 -0.14 7.39 16.73
WN 0.08 0.07 -0.05 -0.30 0.48 11.42
LAST 0.42 0.79 0.74 -9.79 -122.24 98.22
CDG 1.16 2.07 1.93 -61.65 -221.79 262.71
CEG 0.77 1.38 1.28 -41.10 -147.86 175.14
0013 PP 0.13 0.35 0.30 -28.91 54.82 107.51
SW 0.10 0.11 -0.02 -0.14 3.56 36.65
WN 0.08 0.07 -0.05 -0.30 -9.71 24.78
LAST 0.42 0.79 0.18 -9.79 -35.96 246.62
CDG 1.16 2.07 0.63 -61.65 20.01 654.51
CEG 0.77 1.38 0.42 -41.10 13.34 436.34

SACS-IV SYSTEM ELEMENT STRESS REPORT AT MAXIMUM UNITY CHECK
MAXIMUM CRITICAL LOAD DIST ********** APPLIED STRESSES ********** * CM VALUES * * NEXT TWO HIGHEST CASES *
MEMBER GRP UNITY COND. CASE FROM AXIAL ** BENDING ** *** SHEAR *** UNITY LOAD UNITY LOAD
CHECK NO. END Y-Y Z-Z Y Z Y Z CHECK COND CHECK COND
M KGSMM KGSMM KGSMM KGSMM KGSMM
0015-0021 CAB 134.384 EULER WN 0.00 -0.12 0.00 0.00 0.00 0.00 0.85 0.85 3.96 CDG 2.64 CEG
0016-0021 CAB 7.154 TN+BN CDG 0.00 12.88 -115.85 -2.73 0.12 -0.16 0.85 0.85 4.77 CEG 4.15 PP
0020-0021 CAB 7.371 TN+BN CDG 36.30 13.66 -118.87 -3.16 0.12 0.10 0.85 0.85 4.91 CEG 4.28 PP
0021-0019 CAB 164.481 EULER SW 35.43 -0.22 0.00 0.00 0.00 0.00 0.85 0.85 4.19 CDG 2.79 CEG
0022-0021 CAB 132.193 EULER WN 0.00 -0.11 0.00 0.00 0.00 0.00 0.85 0.85 122.66 SW 3.22 CDG
0013-0002 T12 0.112 C<.15 CDG 0.00 -0.38 -0.76 -1.21 0.10 0.03 0.85 0.85 0.07 CEG 0.04 LAST
0000-0020 T16 0.141 TN+BN CDG 4.00 0.00 -4.37 0.00 0.36 0.00 0.85 0.85 0.09 CEG 0.05 LAST
0001-0002 T16 0.123 C<.15 CDG 2.00 -0.08 0.09 3.71 0.15 0.03 0.85 0.85 0.08 CEG 0.05 LAST
0002-0019 T16 0.116 TN+BN CDG 0.00 0.09 0.40 3.48 0.30 0.16 0.85 0.85 0.08 CEG 0.04 LAST
0003-0004 T16 0.030 TN+BN CDG 0.30 0.10 0.22 -0.80 0.17 0.19 0.85 0.85 0.02 CEG 0.01 LAST
0008-0009 T16 0.046 TN+BN CDG 0.00 0.12 0.71 -1.06 0.06 -0.04 0.85 0.85 0.03 CEG 0.02 LAST
0012-0022 T16 0.070 TN+BN CDG 1.89 0.08 -1.35 1.58 0.30 -0.21 0.85 0.85 0.05 CEG 0.03 LAST
0013-0015 T16 0.151 C<.15 CDG 0.00 -0.12 -0.12 4.52 0.12 -0.04 0.85 0.85 0.10 CEG 0.06 LAST
0015-0016 T16 0.193 C<.15 CDG 5.00 -0.09 -5.88 0.02 0.30 -0.02 0.85 0.85 0.13 CEG 0.07 LAST
0016-0014 T16 0.192 C<.15 CDG 0.00 0.00 -5.98 0.02 0.42 0.00 0.85 0.85 0.13 CEG 0.07 LAST

SACS-IV SYSTEM ELEMENT STRESS REPORT AT MAXIMUM UNITY CHECK
MAXIMUM CRITICAL LOAD DIST ********** APPLIED STRESSES ********** * CM VALUES * * NEXT TWO HIGHEST CASES *
MEMBER GRP UNITY COND. CASE FROM AXIAL ** BENDING ** *** SHEAR *** UNITY LOAD UNITY LOAD
CHECK NO. END Y-Y Z-Z Y Z Y Z CHECK COND CHECK COND
M KGSMM KGSMM KGSMM KGSMM KGSMM
0019-0003 T16 0.074 TN+BN CDG 0.00 0.09 -1.94 0.99 0.31 0.19 0.85 0.85 0.05 CEG 0.03 LAST
0020-0001 T16 0.141 C<.15 CDG 0.00 -0.08 -4.28 0.00 0.39 0.03 0.85 0.85 0.09 CEG 0.05 LAST
0022-0013 T16 0.129 TN+BN CDG 1.89 0.07 0.12 3.93 0.25 -0.19 0.85 0.85 0.09 CEG 0.05 LAST

SACS-IV SYSTEM MEMBER INTERNAL LOADS SUMMARY REPORT
MAX. CRIT LOAD DIST * * * * * * * * * * I N T E R N A L L O A D S * * * * * * * * * NEXT TWO HIGHEST CASES

MEMBER GRP UNITY COND COND FROM AXIAL SHEAR SHEAR TORSION BENDING BENDING UNITY LD UNITY LD
CHECK NO. END Y Z Y-Y Z-Z CHECK CN CHECK CN
M MT MT MT MT-CM MT-CM MT-CM
0015-0021 CAB 134.38 EULER WN 0.0 -0.58821E-01-0.48350E-07 0.37318E-07-0.10376E-03-0.16769E-03 0.20185E-03 4.0 CDG 2.6 CEG
0016-0021 CAB 7.15 TN+BN CDG 0.0 6.5281 0.36703E-03 0.30572E-01-0.51022E-01 -18.635 -0.43833 4.8 CEG 4.1 PP
0020-0021 CAB 7.37 TN+BN CDG 36.3 6.9222 -0.20917E-03-0.30509E-01 0.33553E-01 -19.121 -0.50816 4.9 CEG 4.3 PP
0021-0019 CAB 164.48 EULER SW 35.4 -0.11020 -0.92146E-07 0.13173E-06 0.32340E-04 0.36468E-03-0.55134E-04 4.2 CDG 2.8 CEG
0022-0021 CAB 132.19 EULER WN 0.0 -0.55626E-01 0.16736E-06 0.66097E-07 0.77102E-04-0.85964E-04-0.29300E-03122.7 SW 3.2 CDG
0013-0002 T12 0.11 C<.15 CDG 0.0 -4.4787 0.76902E-01 0.55419 5.0067 -61.695 -98.606 0.1 CEG 0.0 LAST
0000-0020 T16 0.14 TN+BN CDG 4.0 0.19190E-01-0.12975E-02 -3.1877 0.11989E-03 -727.42 -0.51892 0.1 CEG 0.0 LAST
0001-0002 T16 0.12 C<.15 CDG 2.0 -1.4631 1.0309 -0.83893 10.365 15.490 617.82 0.1 CEG 0.0 LAST
0002-0019 T16 0.12 TN+BN CDG 0.0 1.6495 -2.1904 -1.4064 54.091 66.297 579.07 0.1 CEG 0.0 LAST
0003-0004 T16 0.03 TN+BN CDG 0.3 1.7623 -1.2289 0.86046 63.849 36.031 -132.42 0.0 CEG 0.0 LAST
0007-0008 T16 0.05 TN+BN CDG 0.0 2.1399 0.19142 0.24347 6.8909 114.19 -181.67 0.0 CEG 0.0 LAST
0008-0009 T16 0.05 TN+BN CDG 0.0 2.0742 0.56008 0.37808E-01 -13.774 117.81 -175.92 0.0 CEG 0.0 LAST
0009-0010 T16 0.04 TN+BN CDG 0.0 1.9454 0.91177 -0.16785 -33.684 111.70 -159.09 0.0 CEG 0.0 LAST
0012-0022 T16 0.07 TN+BN CDG 1.9 1.3778 1.6485 -2.0787 -68.810 -225.23 262.76 0.0 CEG 0.0 LAST
0013-0015 T16 0.15 C<.15 CDG 0.0 -2.0652 -1.0397 0.78139E-01 -14.486 -20.077 753.12 0.1 CEG 0.1 LAST
0015-0016 T16 0.19 C<.15 CDG 5.0 -1.6518 -0.66724 -2.5805 -7.3046 -978.35 3.8278 0.1 CEG 0.1 LAST
0016-0014 T16 0.19 C<.15 CDG 0.0 -0.60433E-02-0.79895E-02 3.7023 0.55158E-03 -995.50 3.9940 0.1 CEG 0.1 LAST

SACS-IV SYSTEM MEMBER INTERNAL LOADS SUMMARY REPORT
MAX. CRIT LOAD DIST * * * * * * * * * * I N T E R N A L L O A D S * * * * * * * * * NEXT TWO HIGHEST CASES

MEMBER GRP UNITY COND COND FROM AXIAL SHEAR SHEAR TORSION BENDING BENDING UNITY LD UNITY LD
CHECK NO. END Y Z Y-Y Z-Z CHECK CN CHECK CN
M MT MT MT MT-CM MT-CM MT-CM
0019-0003 T16 0.07 TN+BN CDG 0.0 1.6485 -1.3778 2.3600 64.224 -322.30 164.93 0.0 CEG 0.0 LAST
0020-0001 T16 0.14 C<.15 CDG 0.0 -1.4631 1.0309 3.2675 10.365 -712.94 -0.61784 0.1 CEG 0.0 LAST
0022-0013 T16 0.13 TN+BN CDG 1.9 1.1561 2.0728 0.63233 -61.652 20.008 654.51 0.1 CEG 0.0 LAST
ESFUERZOS MAXIMO MÁXIMOS EN EL SISTEMA.
De acuerdo a los resultados obtenidos del modelo de análisis se puede observar en el archivo de
salida del modelo de análisis que tanto los miembros de la curva de expansión y el muñón que forma
el atiesador de embarque se encuentran con una relación de esfuerzos por debajo de 1.0,
considerando además que se debe tener un FS=2.0 para la revisión del muñón se tiene entonces una
relación de esfuerzos de 2(0.112) = 0.224 siendo aún menor a 1.0, indicando con lo anterior que los
miembros que se encuentran diseñados dentro de los esfuerzos permisibles que establece el código
API RP 2A WSD; por lo tanto los miembros que forman la curva de expansión y el atiesador de
embarque se consideran adecuados para resistir las acciones a las que se verá sujeta durante las
condiciones de izaje.
DESPLAZAMIENTOS MÁXIMOS EN EL SISTEMA.

7.0 DETALLES DEL ATIESADOR DE EMBARQUE
(VISTA EN PLANTA)
ATIESADOR DE EMBARQUE DE ELM-26 DEL PLANO D-PER1020-ELM-26-Q-203.
7.1 DETALLES DE ABRAZADERA DE ATIESADOR DE EMBARQUE.
DETALLES DE ABRAZADERA DE
8.0 REVISIÓN DE ABRAZADERA

9.0 REVISIÓN POR PUNZONAMIENTO.
(VISTA EN ISOMÉTRICO)
COMBINACIÓN DE CARGAS COM1 1.05 (PP+CM) EN ATIESADOR DE EMBARQUE.

9.1 DETALLES DE LA CORRIDA.

CONTENTS FOR PRE
OPTIONS 1
TUBULAR MEMBER PROPERTIES 2
OPTIMIZATION DATA 4
LOAD CASE STATUS REPORT 5
CONTENTS FOR SLV
SACS PROBLEM DESCRIPTION 1
APPLIED LOAD SUMMARY 2
MATRIX DECOMPOSITION DATA 3
REACTION SUMMARY 4
CONTENTS FOR PST
SACS MODEL PARAMETERS 1
SACS LOAD CASE REPORT 2
PLATE STRESS DETAIL REPORT 4

DATE 18-AUG-2020 TIME 23:06:14 PRE PAGE 1
PRE VERSION 12.0.0.33
** PROGRAM OPTIONS **
UNITS
....METRIC (KG)
EXECUTION
....UNITY CHECK
WSD AISC 13TH EDITION WITH API-RP2A 22ND EDITION FOR TUBULARS
....DKT PLATES SELECTED
....NO SEGMENTS FOR PRISMATIC MEMBERS 1
....NO SEGMENTS/SECTION FOR NON-PRISMATIC MEMBERS 1
REPORTS SELECTED
LOAD
....NO. BASIC LOAD COND. 3
....NO. COMB. LOAD COND. 1

TUBULAR MEMBER PROPERTIES
JOINT WALL OUTSIDE E G AXIAL ***** MOMENTS OF INERTIA **** YIELD KY KZ SHEAR RING SECT TAPER
GRP M/S THICK THICK DIAM. 1000 1000 AREA X-X Y-Y Z-Z STRESS AREA SPACE LENG
M CM CM KGSMM KGSMM CM**2 CM**4 CM**4 CM**4 KGSMM CM**2 M M
ABR 1 0.00 1.905 57.15 20.4 7.9 330.65 0.25261E+06 0.12631E+06 0.12631E+06 24.6 1.0 1.0 165.32 0.00 0.00
OC 1 0.00 1.270 30.48 20.4 7.9 116.54 24906. 12453. 12453. 24.6 1.0 1.0 58.27 0.00 0.00

PLATE GROUP REPORT
PLATE THICK TYPE ELAST POIS. YIELD ********** X-STIFFENERS ********** ********** Y-STIFFENERS ********** *** PLATE OFFSETS ***
GROUP MOD RATIO STRESS TX IY DXU DXL SPAC TY IX DYU DYL SPAC DPY DPX Z-OFF
1000
CM KGSMM KGSMM CM/CM CM**4/CM CM CM CM CM/CM CM**4/CM CM CM CM CM CM CM
ABM 1.905 ISO 20.40.300 24.60 0.000 0.00 0.00 0.00 0.00 0.000 0.00 0.00 0.00 0.00 0.00 0.00 0.00
OCM 1.270 ISO 20.40.300 24.60 0.000 0.00 0.00 0.00 0.00 0.000 0.00 0.00 0.00 0.00 0.00 0.00 0.00

OPTIMIZATION DATA
OPTIMIZED FINAL BANDWIDTH = 20.250 FINAL MAXIMUM BANDWIDTH = 91

**** LOAD CASE STATUS REPORT ****
LOAD LOAD PRINT DEAD P-DELTA LOAD AMOD

CASE ID OPTION LOAD LOAD FACTOR FACTOR
1 C1 YES NO NO 1.00 1.00

2 C2 YES NO NO 1.00 1.00
3 PP YES NO NO 1.00 1.00
4 COM1 YES NO NO 1.00 1.00

DATE 18-AUG-2020 TIME 23:06:14 SLV PAGE 1
SLV VERSION 12.0.0.32
** SACS PROBLEM DESCRIPTION **
NUMBER OF JOINTS .......... 2760
NUMBER OF BEAMS ........... 0
NUMBER OF PLATES .......... 2844
NUMBER OF SHELLS .......... 0
NUMBER OF SOLIDS .......... 0
NUMBER OF LOADS ........... 3
NUMBER OF MASTER JOINTS ... 0
PRINT OPTION .............. 0

APPLIED LOAD SUMMARY

NO. ID KG KG KG
1 C1 -4.064201E+03 7.257482E+01 4.989521E+02

2 C2 -4.064201E+03 7.257482E+01 -5.171001E+02
3 PP 0.000000E+00 0.000000E+00 -1.160021E+03

MATRIX TRIANGULARIZATION COMPLETE
MAX. SIGNIFICANT DIGITS LOST = 0 SOLUTION ACCURATE TO 15 DIGITS OUT OF POSSIBLE 15
FORWARD SUBSTITUTION COMPLETE
BACK SUBSTITUTION COMPLETE

FIXED DEGREE OF FREEDOM REACTION SUMMARY

NO. ID KG KG KG
1 C1 4.064201E+03 -7.257482E+01 -4.989521E+02

2 C2 4.064201E+03 -7.257482E+01 5.171001E+02
3 PP -9.114383E-10 -2.937560E-10 1.160021E+03

DATE 18-AUG-2020 TIME 23:06:19 PST PAGE 1
PST VERSION 12.0.0.48
******* SACS MODEL PARAMETERS ********
NUMBER OF JOINTS .............. 2760
NUMBER OF MEMBERS ............. 0
NUMBER OF PLATES .............. 2844
NUMBER OF SHELL ELEMENTS ...... 0
NUMBER OF SOLID ELEMENTS ...... 0
NUMBER OF BASIC LOADS ......... 3
NUMBER OF COMBINED LOADS ...... 1
UNITY CHECK .... WSD AISC 13th / API RP2A-WSD 22ND

JOINT DEFLECTION REPORT ...................NO
GROUP SUMMARY REPORT ......................NO
ELEMENT STRESS AT MAXIMUM UC REPORT .......NO
MEMBER INTERNAL LOADS SUMMARY REPORT ......NO
ELEMENT UNITY CHECK REPORT ................NO
ELEMENT DETAIL REPORT .....................NO
MEMBER END FORCES AND MOMENTS REPORT ......NO
JOINT REACTIONS REPORT ....................NO

***** SACS LOAD CASE REPORT *****
LOAD LOAD TYPE PRINT AMOD WATER LC FACTOR LC FACTOR LC FACTOR LC FACTOR LC FACTOR LC FACTOR
NO. CASE OPTION FACTOR DEPTH
M
1 C1 BASIC YES 1.000 0.0
2 C2 BASIC YES 1.000 0.0
3 PP BASIC YES 1.000 0.0
4 COM1 COMB YES 1.000 0.0 C1 1.05 C2 1.05 PP 1.05

*** SACS POST PROCESSOR COMMENTS ***
** THE USER SHOULD TAKE NOTE OF THE FOLLOWING COMMENTS REGARDING THE SACS POST PROCESSOR OUTPUT **
BEAMS
(1) INTERNAL LOADS FOR MEMBERS ARE PRESENTED IN THE CLASSICAL ENGINEERING SIGN
CONVENTION AS DESCRIBED BY TIMOSHENKO
(2) IF THE AXIAL COMPRESSIVE LOAD ON A MEMBER EXCEEDS THE EULER BUCKLING LOAD, THEN THE
AXIAL UNITY CHECK VALUE FOR THE MEMBER IS AUGMENTED BY 100 TO INDICATE THAT THE
MEMBER HAS BUCKLED
(3) THE MAXIMUM COMBINED UNITY CHECK CAN BE THE MAXIMUM SHEAR UNITY CHECK IF IT IS
GREATER THAN THE MAXIMUM UNITY CHECK DUE TO BENDING AND AXIAL LOAD
(4) THE FOLLOWING ABBREVIATIONS ARE USED TO DESCRIBE THE CRITICAL UNITY CHECK CONDITIONS:
LOCAP - LOCAL CAPACITY AT CONE-CYLINDER JUNCTION

SHEAR - SHEAR
CM+BN - COMPRESSION WITH BENDING
TN+BN - TENSION WITH BENDING
WEB-SH - WEB SHEAR
FLG-SH - FLANGE SHEAR
EULER - EULER BUCKLING
HOOP - CONES: HOOP COMPRESSION OR TENSION
HYDRO - HYDROSTATIC COLLAPSE
TR+SFA - TORSION,SHEAR,FLEXURE AND AXIAL (FOR HSS ONLY)
(5) THE FOLLOWING ABBREVIATIONS ARE USED TO DESCRIBE THE CRITICAL UNITY CHECK CONDITIONS FOR CONCRETE:
COLBUC - COLUMN BUCKLING

CM+BN - COMPRESSION WITH BENDING IN COLUMN ELEMENT
TN+BN - TENSION WITH BENDING IN COLUMN ELEMENT
SHEAR - SHEAR
TORS - TORSION
BEND-Y - PURE BENDING IN BEAM ELEMENT ABOUT LOCAL Y AXIS
REINF - REINFORCEMENT RATIO
(NOTE) WHEN USING THE AISC 13th/14th EDITION (2005/2010 SPECIFICATIONS) CODE CHECK, THE USER SHOULD HAVE THE P-DELTA EFFECT
INCLUDED IN THE ANALYSIS
(6) FOR EARTHQUAKE ANALYSIS WITH 'PRST' OR 'PRSC' OPTION, ONLY THE FORCES AND MOMENTS AT MEMBER ENDS ARE MEANINGFUL.
'JO' STRESS OPTION IS RECOMMENDED.
PLATES
(1) MEMBRANE STRESSES ARE GIVEN AT THE NEUTRAL AXIS OF THE PLATE IN THE LOCAL
COORDINATE SYSTEM OF THE PLATE . ALSO THE PRINCIPAL MEMBRANE STRESS AND
MAXIMUM SHEAR STRESS ARE GIVEN
(2) THE DIRECT STRESSES RESULTING FROM OUT OF PLANE BENDING ARE GIVEN AT THE UPPER
SURFACE OF THE PLATE (POSITIVE LOCAL Z DIRECTION) IN THE LOCAL COORDINATE SYSTEM
OF THE PLATE . ALSO THE PRINCIPAL BENDING STRESS AND MAXIMUM SHEAR STRESS ARE GIVEN
(3) THE MAXIMUM PRINCIPAL STRESS AND MAXIMUM SHEAR STRESS FOR THE COMBINED MEMBRANE
AND BENDING STRESS ARE GIVEN . THE UNITY CHECK VALUE IS BASED ON THESE STRESSES
ESFUERZOS MÁXIMOS EN EL SISTEMA
DESPLAZAMIENTOS MÁXIMOS EN EL ATIESADOR DE EMBARQUE.

10.0 CONCLUSIONES.
Una vez realizado el análisis y revisión estructural del atiesador de embarque del oleogasoducto de 16” Ø
X 3.5 km aprox de la plataforma ELM-26 hacia interconexión submarina mediante hot tapping en
oleogasoducto de 20” Ø x 22 km de TETL -A hacia Tlacame, se concluye lo siguiente.
Las abrazaderas cumplen con los criterios de revisiones de capacidad de carga y corte del perno,
revisión del patín por corte, revisión por tensión, aplastamiento de la placa revisión por tensión, flexión y
aplastamiento de la placa; así mismo se realizó la revisión de la placa que conforman las abrazaderas y
por último la revisión por punzonamiento dando resultados dentro de los criterios utilizados.
El perfil del atiesador de embarque presenta una condición segura siempre y cuando los puntos de izaje
o apoyo no sean inferiores a los considerados en esta memoria de cálculo. Así mismo, las deformaciones
provocadas por la carga de gravedad registran parámetros de flexibilidad adecuada en la estructura.
Esta memoria de cálculo se realizó de acuerdo con el plano D-PER1020-ELM-26-Q-203_0, plano de

detalle constructivo de curva de expansión, ELM-26.

Per01020-Elm-26-Mc-Q-008 Rev 0

Cargado por

Copyright:

Formatos disponibles

Per01020-Elm-26-Mc-Q-008 Rev 0

Cargado por

Información del documento

Título original

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

Per01020-Elm-26-Mc-Q-008 Rev 0

Cargado por

Copyright:

Formatos disponibles

MEMORIA DE CÁLCULO

“INGENIERÍA, PROCURA Y CONSTRUCCIÓN DE UNIDAD DE

SUBDIRECCIÓN DE PROYECTOS DE EXPLOTACIÓN ESTRATÉGICOS

No. Contrato: 640859821

MEMORIA DE CÁLCULO DE ATIESADOR DE EMBARQUE DE LA

“OLEOGASODUCTO DE 16”Ø x 3.5 KM APROX. DE ELM-26

0 SEP/2020 APROBADO PARA CONSTRUCCIÓN J.L.C.C. J.A.U.P. M.N.L.M. R.C.G. S.D.S.M.

REVISÓ VALIDÓ COORDINÓ APROBÓ

1.0 ALCANCE DEL ANÁLISIS. ......................................................................................... 3

2.0 DATOS DEL ANÁLISIS. .............................................................................................. 3

2.1 DATOS DE LA CURVA DE EXPANSIÓN DE PROYECTO. ........................................ 3

2.2 DATOS DEL ATIESADOR DE EMBARQUE. .............................................................. 4

3.0 BASES DEL ANÁLISIS................................................................................................ 4

3.1 CARGAS CONSIDERADAS. ....................................................................................... 4

3.2 FACTOR DE CARGA DINÁMICA. ............................................................................... 5

4.0 MODELO. ..................................................................................................................... 6

4.1 MODELO DE CURVA DE EXPANSIÓN. .................................................................... 7

4.2 CABLES PARA IZAJE. ................................................................................................ 9

5.0 CARGAS CONSIDERADAS EN EL ANÁLISIS. .......................................................... 9

6.0 LISTADO DE RESULTADOS DEL ANÁLISIS. .......................................................... 13

7.0 DETALLES DEL ATIESADOR DE EMBARQUE ....................................................... 29

7.1 DETALLES DE ABRAZADERA DE ATIESADOR DE EMBARQUE. ........................ 29

8.0 REVISIÓN DE ABRAZADERA .................................................................................. 30

9.0 REVISIÓN POR PUNZONAMIENTO. ........................................................................ 40

9.1 DETALLES DE LA CORRIDA. .................................................................................. 41

10.0 CONCLUSIONES. ...................................................................................................... 45

1.0 ALCANCE DEL ANÁLISIS.

Esta memoria comprende el análisis de los atiesadores de embarque de la curva de expansión a

Los atiesadores de embarque de la curva de expansión tienen la función estructural de brindar la

2.0 DATOS DEL ANÁLISIS.

Curva de Expansión interconexión submarina.

2.2 DATOS DEL ATIESADOR DE EMBARQUE.

Datos del atiesador (Tubo circular “OC”)

Especificación del acero: A-53 Grado B

3.0 BASES DEL ANÁLISIS.

Normativamente el análisis cumple con lo establecido en el API RP 2A-WSD “Recommended

3.1 CARGAS CONSIDERADAS.

Peso propio y cargas adicionales.

Figura 1. Factores de contingencia indicados en la tabla 15 de la ETP-041, “Carga, Amarre,

3.2 FACTOR DE CARGA DINÁMICA.

Los elementos estructurales y juntas tubulares, se revisan considerando un factor de amplificación

Figura 2. Factores de ampliación dinámica.

CDG = (PE) FAD.

CDG: Carga dinámica en el Gancho.

Sustituyendo valores en la ecuación:

• Solo cuenta con un punto de apoyo, el gancho de la grúa.

4.1 MODELO DE CURVA DE EXPANSIÓN.

PUNTOS DE IZAJE BRIDA SWIVEL

4.00 7.89 3.11

4.2 CABLES PARA IZAJE.

5.0 CARGAS CONSIDERADAS EN EL ANÁLISIS.

Datos de las cargas por gravedad

CARGAS APLICADAS POR PESO PROPIO EN CURVA DE EXPANSIÓN.

CARGAS APLICADAS POR CARGAS DE LASTRE DE CONCRETO EN CURVA DE EXPANSIÓN.

COMBINACIÓN DE CARGAS CDG 1.575 (PP+CM) EN CURVA DE EXPANSIÓN.

6.0 LISTADO DE RESULTADOS DEL ANÁLISIS.

CONTENTS FOR SLV

SACS PROBLEM DESCRIPTION 1

CONTENTS FOR PST

* OFFSETS * SLENDERNESS

LOAD CASE STATUS REPORT

SACS PROBLEM DESCRIPTION

* SACS MODEL PARAMETERS **

* SACS LOAD CASE REPORT *