Memoria de Calculo - Estructuras

Memoria de Cálculo
Estructural
Edificio Multifamiliar
Trinidad y Morán
Consorcio Casuarinas sac
Alberto Ordóñez Curotto, Ph.D.
12 de Agosto del 2022
_________________________________________________________________________________________
[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

MEMORIA DE CALCULO ESTRUCTURAL
1.0. GENERALIDADES
El presente proyecto estructural “Edificio Multifamiliar” se encuentra ubicado en el

distrito de Lince.
1.1. UBICACIÓN
La presente memoria de cálculo corresponde al Proyecto Estructural “Edificio

Multifamiliar”, que ésta ubicado en la Calle Trinidad y Morán Nº 1294 – 1298, esquina
con Calle Sinchi Roca, Distrito de Lince, provincia de Lima, departamento de Lima.
2.0. OBJETIVOS
La presente memoria de cálculo tiene por objetivo general sustentar el análisis y diseño
estructural de los diferentes elementos estructurales tales como, cimentación, vigas de
cimentación, muros de sostenimiento, losas aligeradas, losas macizas, vigas, columnas
y placas.
2.1. OBJETIVOS ESPECÍFICOS
La presente memoria de cálculo tiene por objetivos específicos:
- Determinar el Sistema Estructural Sismorresistente utilizado en el proyecto

considerando las dimensiones, geometría y funcionalidad de la Edificación.
- Determinar el Espectro Sísmico usado en el proyecto con las consideraciones
tomadas de los parámetros sismorresistentes.
- Determinar los desplazamientos máximos permitidos por el Reglamento
Nacional de Edificaciones.
_________________________________________________________________________________________

3.0. CÓDIGOS Y REGLAMENTOS
3.1 NORMAS NACIONALES
Se sigue las disposiciones del Reglamento Nacional de Edificaciones (RNE):

Norma Técnica de Edificaciones E.020 – Cargas.
Norma Técnica de Edificaciones E.030 – Diseño Sismorresistente.
Norma Técnica de Edificaciones E.050 – Suelos y Cimentaciones.
Norma Técnica de Edificaciones E.060 – Concreto Armado.
Norma Técnica de Edificaciones E.070 – Albañilería.
3.2. NORMAS INTERNACIONALES Y DOCUMENTOS DE REFERENCIA
Norma Internacional ACI 318R-14.

4.0. DESARROLLO DE CRITERIOS DE DISEÑO
4.1. CONDICIONES DE MECÁNICA DE SUELOS
Del Estudio de Mecánica de Suelos obtenemos lo siguiente:
Angulo de fricción = 34 º
Factores para el empuje de suelos: Ka = 0.29 Kp = 3.96
Resistencia admisible = 4.00 kg/cm2
4.2. ESPECIFICACIONES TECNICAS DE MATERIALES
Los materiales empleados para el diseño de los elementos estructurales poseen las
siguientes características:
4.2.1 CONCRETO:
- Resistencia a la compresión f’c: 280 Kg/cm2 en la cisterna
- Resistencia a la compresión f’c: 210 Kg/cm2 en el resto de elementos
- Resistencia a la compresión f’c: 100 Kg/cm2 en rellenos
4.2.2 ACERO DE REFUERZO GRADO 60:

- Resistencia a la fluencia fy: 4200 Kg/cm2
4.3.1 ALBAÑILERIA CONFINADA:

Ladrillos que presentan como mínimo las siguientes características:
- Resistencia a la compresión f’m: 65.0 kg/cm2
- Resistencia al corte v’m: 8.1 kg/cm2
- Módulo de elasticidad Em : 32,500 kg/cm2
- Módulo de corte, Gm : 13,000 kg/cm2
- Módulo de Poisson: 0.25
_________________________________________________________________________________________

4.4. CARGAS DE DISEÑO
Se han considerado los siguientes tipos de carga:
CARGAS MUERTAS (D):
- Peso de elementos de concreto armado : 2400 kg/m3

- Peso de unidades de albañilería sólida : 1800 kg/m3
- Peso acabados con mortero : 100 kg/m2
CARGAS VIVAS (L):

- Sobrecarga en techos de concreto (Azotea) : 150 kg/m2
- Sobrecarga en losas aligeradas de vivienda : 200 kg/m2
- Sobrecarga en losas de estacionamientos : 250 kg/m2
CARGAS DE SISMO (S):

- Según norma de diseño sismorresistente: Sa = (ZUCS.g) /R
CARGAS POR EMPUJES LATERALES DEL TERRENO (H):

- Presión lateral estática :
- Presión lateral dinámica :
CARGAS POR PRESION DE LIQUIDOS (F):
- Según expresión :
4.4. COMBINACIONES DE CARGAS
La resistencia requerida de los elementos y sus conexiones fueron determinadas

mediante un análisis elástico – lineal teniendo en cuenta las cargas que actúan sobre la
estructura definida anteriormente y con las combinaciones de carga correspondientes.
Se tuvieron en cuenta las combinaciones de cargas factorizadas recomendadas por el

reglamento nacional de edificaciones, aplicando el método de Resistencia para
determinar el Diseño de los elementos que conforman la estructura.
- COMB 1 = 1.4D+1.7L
- COMB 2 = 1.25(D+L)+-S
- COMB 3 = 0.9D+-S
- ENVOLCX=COMB1+COMB2+COMB3
Donde:
D = Carga Muerta
L = Carga Viva
S = Cargas de Sismo
_________________________________________________________________________________________

5.0. ESTRUCTURACIÓN
5.1.1. Sistema de Muros Estructurales en la dirección X y Z.
5.1.2. Número de pisos proyectados
El proyecto contempla la construcción de un semisótano y 5 pisos, la altura de piso a

piso es de 2.70m.
5.2. PREDIMENSIONAMIENTO DE ELEMENTOS ESTRUCTURALES
5.2.1. ELEMENTOS DE CONCRETO ARMADO f’c = 210 Kg/cm2
- Vigas principales y secundarias:
Según RNE:
H = L/12; H = 7.0/12 = 0.58 m. Consideramos H=0.55 m.
B = H/2; H = 0.55/2 = 0.275 m.
- Columnas estructurales:
Según ACI:
Columna centrada: Acol = Pserv / 0.45f’c
Acol=(5.30m.x4.91m.)(1500Kg/m2)x(6Piso)/0.45x(210Kg/cm2)=2478.38 cm2
_________________________________________________________________________________________

Ancho de la columnas = 25 cm Largo de la columna = 2478.38/25 = 100 cm
Dimensiones de la columna 25 cm x 100 cm
Se considera 25 cm x 160 cm
Verificación de Rigidez:
Vigas = Rv = 25x55^3/(12x700) = 495 cm3
Columnas Rc = 25x160^3/(12/270) = 31,605 cm3
Caso más desfavorable Rc /2 Rv = 31,605/990 = 31.92 > 1.2 OK
Kcol/Kvig >31.92
- Losa Aligerada:
Según ACI 318:14 - 8.3.1.2: Losa Aligerada unidireccional
H = Ll/25 ;
Donde:
Ll=Luz libre mayor =5.00 m. H = 500/25 = 20 cm
6.0. ANÁLISIS ESTRUCTURAL
6.6.1. PARÁMETROS SISMICOS
El análisis sísmico se desarrolló de acuerdo con las indicaciones de la Norma Peruana

de Diseño Sismorresistente E.030.
Z = Factor de zona.
U = Factor de Uso o de importancia.
S = Factor del suelo.
C = Coeficiente sísmico, según el periodo.
R = Factor de Reducción.
g = valor de la aceleración de la gravedad.
T = Aceleración del suelo
_________________________________________________________________________________________

Para nuestro caso:
Z= 0.45 Por ser zona 4 de acuerdo al reglamento.
U= 1.00 Por ser un edifico de vivienda (Categoría C)
S= 1.00 Por ser considerado suelo tipo S1; Tp(s) = 0.40 TL(s) = 2.5
Tp = 0.40 Suelo tipo S1
Rx = 6 Ry= 6 Sistema predominantemente Muros Estructurales de concreto

armado Regular en la dirección X y Z.
Altura = 6 x 2.70 m = 16.20 m Tx = 16.20/60 = 0.27 < Tp Tz = 16.20/60 = 0.27 < Tp
C = 2.5; Si T<Tp en ambos casos Coeficiente de amplificación Sísmico.
6.6.2. DESCRIPCIÓN DE ELEMENTOS ESTRUCTURALES
- Vigas principales y secundarias: 0.25 m x 0.55 m
- Columnas estructurales: 0.25 m x 1.60 m. y 0.25 m x 1.80 m
- Losa Aligerada en un sentido de peralte de 0.20 m., ancho de vigueta = 0.10 m.
6.6.3. ANÁLISIS BAJO CARGAS DE GRAVEDAD
CARGA MUERTA (CM):
Peso de losa aligerada en un sentido de H = 0.20 m. 0.30 Tn/m2
Acabados de piso 0.10 Tn/m2
Tabiquería 0.10 Tn/m2
CARGA VIVA (CV):
Losa aligerada en azotea: 0.15 Tn/m2
Losa aligerada en el resto de pisos 0.20 Tn/m2
Losa aligerada en estacionamientos 0.25 Tn/m2
Luego las cargas se llevan a cargas ultimas utilizando los factores de amplificación
dados por la norma E.0.60 de concreto armado.
Wu = 1.4 CM + 1.7 CV
_________________________________________________________________________________________

6.6.4. ESPECTRO SISMICO PARA LA DIRECCION X y Z
El programa STAAD PRO, con licencia, toma como ejes cartesianos a X y Z.
ANÁLISIS SISM ICO DE EDIFICIO TRINIDAD Y M ORAN

ESPECTRO DE DISEÑO E-030
Z= 4 0,45 SX 1,0820
U= C 1,00 SY 1,0820
S= S1 1,00
Tp= (S1) 0,40 TL= 2,5
Rx = 4,08 MUROS ESTRUCTURALES IRREGULAR
Ry = 4,08 MUROS ESTRUCTURALES IRREGULAR
Factor de
Amplificaci Aceleracion Espectral
T(Seg) Direccion X Direccion Y
on Sismica
C Sax (m/s2) Say (m/s2)
0 2,500 2,7050 2,7050
0,1 2,500 2,7050 2,7050
0,2 2,500 2,7050 2,7050
0,3 2,500 2,7050 2,7050
0,4 2,500 2,7050 2,7050
0,5 2,000 2,1640 2,1640
0,6 1,667 1,8033 1,8033
0,7 1,429 1,5457 1,5457
0,8 1,250 1,3525 1,3525
0,9 1,111 1,2022 1,2022
1 1,000 1,0820 1,0820
1,1 0,909 0,9836 0,9836
1,2 0,833 0,9017 0,9017
1,3 0,769 0,8323 0,8323
1,4 0,714 0,7728 0,7728
1,5 0,667 0,7213 0,7213
1,6 0,625 0,6762 0,6762
1,7 0,588 0,6365 0,6365
1,8 0,556 0,6011 0,6011
1,9 0,526 0,5695 0,5695
2 0,500 0,5410 0,5410
2,1 0,476 0,5152 0,5152
2,2 0,455 0,4918 0,4918
2,3 0,435 0,4704 0,4704
2,4 0,417 0,4508 0,4508
2,5 0,400 0,4328 0,4328
2,6 0,385 0,4161 0,4161
2,7 0,370 0,4007 0,4007
2,8 0,357 0,3864 0,3864
2,9 0,345 0,3731 0,3731
3 0,333 0,3607 0,3607
3,1 0,323 0,3490 0,3490
3,2 0,313 0,3381 0,3381
3,3 0,303 0,3279 0,3279
3,4 0,294 0,3182 0,3182
3,5 0,286 0,3091 0,3091
3,6 0,278 0,3006 0,3006
3,7 0,270 0,2924 0,2924
3,8 0,263 0,2847 0,2847
3,9 0,256 0,2774 0,2774
4 0,250 0,2705 0,2705
_________________________________________________________________________________________

Coeficientes de Reducción:
R=Ro x Ia x Ip
Ro Coef. Básico de Reducción (Ver Tabla Nº7)

Ia Irregularidad de altura (Ver Tabla Nº8)
Ip Irregularidad de planta Ver Tabla Nº9)
Irregularidades Estructurales en Altura Eje X-X Eje Y-Y

Irregularidad de Rigidez – Piso Blando 1,00 1,00
Irregularidad de Resistencia – Piso Debil 1,00 1,00
Irregularidad Extrema de Rigidez 1,00 1,00
Irregularidad Extrema de Resistencia 1,00 1,00
Irregularidad de Masa o Peso 1,00 1,00
Irregularidad de Geometría Vertical 1,00 1,00
Discontinuidad en Sistemas Resistentes 0,80 0,80
Discontinuidad Extrema de los Sistemas Resistentes 1,00 1,00
Se toma el valor más critico 0,80 0,80
Irregularidades Estructurales en Planta Eje X-X Eje Y-Y

Irregularidad Torsional 1,00 1,00
Irregularidad Torsional Extrema 1,00 1,00
Esquinas Entrantes 1,00 1,00
Discontinuidad de Diafragma 0,85 0,85
Sistemas no Paralelos 1,00 1,00
Se toma el valor más critico 0,85 0,85
R=Ro x Ia x Ip Ro Ia Ip R
Rx 6 0,80 0,85 4,080
Ry 6 0,80 0,85 4,080
ESPECTRO DE DISEÑO E-030

Aceleracion Espectral
3,0
2,5
2,0
Series1
1,5
Sa (m/s2)
1,0
0,5
0,0
0 1 2 3 4 5
T (seg)
_________________________________________________________________________________________

6.6.5. PERIODOS FUNDAMENTALES Y PORCENTAJE DE PARTICIPACION DE
MASAS
6.6.5.1. Periodos Fundamentales: Usando el programa con licencia Staad Pró
Tx= 0.70642 seg. Tz= 0.21437 seg.
_________________________________________________________________________________________

6.6.5.2. Porcentajes de Participación de Masas:
Porcentajes de Participación de Masas en X:
Porcentajes de Participación de Masas en Z:
_________________________________________________________________________________________

6.6.6. VERIFICACION DE LA CORTANTE MINIMA BASAL
Edificio Multifamiliar Trinidad y Morán

Consorcio Inmobiliario Casuarinas
Según RNE Cap. 2.5
Si T<Tp; C=2,5
Tp 0,40 Grava
Z 0,45 Lima
U 1,00 Vivienda
S 1,00
H 16,20 m
Ctx 60,00 Muros Estructurales
Cty 60,00 Muros Estructurales
Tx 0,270 < 0,40

Ty 0,270 > 0,40
Cx 2,50
Cy 2,50
Rx 4,08 Muros Estructurales Irreg
Ry 4,08 Muros Estructurales Irreg
Cx/Rx 0,61
Cy/Ry 0,61
Coef sismico X 0,28
Coef sismico Y 0,28
Peso 939,13 Tn Modelo
Sismo Est. Sx 258,95 Tn
Sismo Est. Sy 258,95 Tn
Sismo Sx (90%) 233,06 Tn
Sismo Sy (90%) 233,06 Tn
Cortante Din X 105,28 Tn Modelo
Cortante Din Y 135,53 Tn Modelo
Factor Mayor en X 2,21 SI

Factor Mayor en Y 1,72 SI
_________________________________________________________________________________________

6.6.7. Diseño de la estructura
Se presenta las dimensiones del edificio así como las cargas sobre el mismo
DIMENSIONES:
CARGA MUERTA:
_________________________________________________________________________________________

CARGA VIVA:
CARGAS DE SISMO:
_________________________________________________________________________________________

DIAFRAGMA RIGIDO:
3 DIMENSIONES:
_________________________________________________________________________________________

6.6.7.1 CONTROL DE DESPLAZAMIENTOS
Deformación máxima en Eje X:
Para estructuras irregulares los desplazamientos laterales se calculan multiplicando por

0.85R los resultados obtenidos del análisis lineal y elástico con las solicitaciones
sísmicas reducidas.
EJE 2
Desplaz. Absoluto máx. 1 = 1.306 cms.
Altura de piso: 270 cms.
Factor de Reducción en X: R=4.08
Deriva en X=(1.306-0.818)x0.85x4.08/270=0.006<0.007
Para ambas direcciones se cumple con los límites establecidos por la Norma Peruana
Sismo resistente E-0.30, de acuerdo al sistema estructural de cada dirección.
_________________________________________________________________________________________

Deformación máxima en Eje Z:
Para estructuras irregulares los desplazamientos laterales se calculan multiplicando por

0.85R los resultados obtenidos del análisis lineal y elástico con las solicitaciones
sísmicas reducidas.
EJE B
Altura de piso: 270 cms.
Factor de Reducción en X: R=4.08
Deriva en X=(0.367-0.227)x0.85x4.08/270=0.002<0.007
Para ambas direcciones se cumple con los límites establecidos por la Norma Peruana
Sismo resistente E-0.30, de acuerdo al sistema estructural de cada dirección.
_________________________________________________________________________________________

7.0. DISEÑO ESTRUCTURAL
7.1. DISEÑO DE ELEMENTOS ESTRUCTURALES
7.1.1 CIMENTACIONES
Diseño de la cimentación usando Asdip Foundation con Licencia
Utilizando los valores de las reacciones de columnas, muros de contención y placas

para las diferentes combinaciones de carga se diseñan las zapatas centradas con el
programa Midas Design+ y las zapatas excéntricas y vigas de cimentación con el
programa Asdip Foundation.
Se presentan los resultados de las reacciones:
Reacciones para Carga de Servicio
_________________________________________________________________________________________

Reacciones para Carga Última
Reacciones para 1.25(PP+CM+CV)+SX
_________________________________________________________________________________________

Reacciones para 1.25(PP+CM+CV)+SZ
Reacciones para 0.90(PP+CM)+SX
_________________________________________________________________________________________

Reacciones para 0.90(PP+CM)+SZ
_________________________________________________________________________________________

ALBORIC Project: Edificio Multifamiliar Trinidad y Moran Page #
Engineer: Victor Quispe 14/08/2022
Descrip: Z-3
ASDIP Foundation 4.7.1.1 SPREAD FOOTING DESIGN www.asdipsoft.com
Footing Length (X-dir) ............ m Gross Allow. Soil Pressure ....... 40.0 Tn/m²
Footing Width (Z-dir) .............. m Soil Pressure at Corner 1 ......... 33.3 Tn/m²
Footing Thickness .................. cm OK Soil Pressure at Corner 2 ......... 33.0 Tn/m²
Soil Cover .............................. m Soil Pressure at Corner 3 ......... 31.3 Tn/m²
Column Length (X-dir) ........... cm Soil Pressure at Corner 4 ......... 31.5 Tn/m²
Column Width (Z-dir) .............. cm Bearing Pressure Ratio ................. 0.83 OK
Offset (X-dir) ........................... cm OK Ftg. Area in Contact with Soil ........ 100.0 %
Offset (Z-dir) ........................... cm OK X-eccentricity / Ftg. Length ............ 0.00 OK
Pedestal Height .................. N. A. Z-eccentricity / Ftg. Width .............. 0.00 OK
Service Factored
Axial Force P ........... Tn
Moment about X Mx Tn-m
Moment about Z Mz Tn-m
Shear Force Vx ........ Tn
Shear Force Vz ........ Tn
- Moment Mx = 0.1 Tn-m

- Shear Force Vz = 0.1 Tn
Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 0.1 * 0.60 = 0.1 Tn-m
- Passive Force = 0.0 Tn Arm = 0.24 m Moment = 0.0 Tn-m
- Overturning moment X-X = 0.1 + 0.1 = 0.2 Tn-m
- Footing weight = 1.60 * 2.85 * 60.0 / 100 * 2.41 = 6.6 Tn

Arm = 1.60 / 2 = 0.80 m Moment = 6.6 * 0.80 = 5.3 Tn-m
- Pedestal weight = 30.0 / 100 * 210.0 / 100 * 0.0 * 2.41 = 0.0 Tn
Arm = 1.60 / 2 - 0.0 / 100 = 0.80 m Moment = 0.0 * 0.80 = 0.0 Tn-m
- Soil cover = (1.60 * 2.85 - 30.0 / 100 * 210.0 / 100) * 0.5 * 1800 = 3.5 Tn
Arm = 1.60 / 2 = 0.80 m Moment = 3.5 * 0.80 = 2.8 Tn-m
- Buoyancy = 1.60 * 2.85 * 1.0 * (-0.10) = 0.0 Tn
Arm = 1.60 / 2 = 0.80 m Moment = 0.0 * 0.80 = 0.0 Tn-m
- Axial force P = 137.0 Tn
Arm = 1.60 / 2 - 0.0 / 100 = 0.80 m Moment = 137.0 * 0.80 = 109.6 Tn-m
- Resisting moment X-X = 5.3 + 0.0 + 2.8 + 109.6 + 0.0 = 117.7 Tn-m
117.7
- Overturning safety factor X-X = = = 99.99 > 1.50 OK
0.2
1 of 9
Project: Edificio Multifamiliar Trinidad y Moran Page #
Descrip: Z-3
- Moment Mz = 1.2 Tn-m

- Shear Force Vx = 1.1 Tn
Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 1.1 * 0.60 = 0.7 Tn-m
- Overturning moment Z-Z = 1.2 + 0.7 = 1.9 Tn-m

Arm = 2.85 / 2 = 1.43 m Moment = 6.6 * 1.43 = 9.4 Tn-m
Arm = 2.85 / 2 - 0.0 / 100 = 1.43 m Moment = 0.0 * 1.43 = 0.0 Tn-m
- Soil cover = (1.60 * 2.85 - 30.0 / 100 * 210.0 / 100) * 0.5 * 1800 = 3.5 Tn
Arm = 2.85 / 2 = 1.43 m Moment = 3.5 * 1.43 = 5.0 Tn-m
- Buoyancy = 1.60 * 2.85 * 1.0 * (-0.10) = 0.0 Tn
Arm = 2.85 / 2 = 1.43 m Moment = 0.0 * 1.43 = 0.0 Tn-m
Arm = 2.85 / 2 - 0.0 / 100 = 1.43 m Moment = 137.0 * 1.43 = 195.2 Tn-m
- Resisting moment Z-Z = 9.4 + 0.0 + 5.0 + 195.2 + 0.0 = 209.6 Tn-m
209.6
- Overturning safety factor Z-Z = = = 99.99 > 1.50 OK
1.9
Overturning moment X-X = 0.1 + 0.1 = 0.2 Tn-m

Resisting moment X-X = 5.3 + 0.0 + 2.8 + 0.0 + 109.6 = 117.7 Tn-m
Overturning moment Z-Z = 1.2 + 0.7 = 1.9 Tn-m
Resisting moment Z-Z = 9.4 + 0.0 + 5.0 + 0.0 + 195.2 = 209.6 Tn-m
Resisting force = 6.6 + 0.0 + 3.5 - 0.0 + 137.0 = 147.1 Tn
X-coordinate of resultant from maximum bearing corner:
209.6 - 1.9
Xp = = = 1.41 m
147.1
Z-coordinate of resultant from maximum bearing corner:
117.7 - 0.2
Zp = = = 0.80 m
147.1
X-ecc = 2.85 / 2 - 1.41 = 0.01 m
Z-ecc = 1.60 / 2 - 0.80 = 0.00 m
Area = 1.60 * 2.85 = 4.6 m²
Sx = 2.85 * 1.60² / 6 = 1.2 m³
Sz = 1.60 * 2.85² / 6 = 2.2 m³
- Footing is in full bearing. Soil pressures are as follows:
P1 = 147.1 * (1 / 4.6 + 0.00 / 1.2 + 0.01 / 2.2) = 33.25 Tn/m²
P2 = 147.1 * (1 / 4.6 - 0.00 / 1.2 + 0.01 / 2.2) = 32.99 Tn/m²
P3 = 147.1 * (1 / 4.6 - 0.00 / 1.2 - 0.01 / 2.2) = 31.27 Tn/m²
P4 = 147.1 * (1 / 4.6 + 0.00 / 1.2 - 0.01 / 2.2) = 31.54 Tn/m² 2 of 9
Descrip: Z-3
Internal friction angle = 33.0 deg Active coefficient ka = 0.29

Passive coefficient 1 / 0.29 = 3.39
Pressure at mid-depth = 3.39 * 1800 * (0.50 + 60.0 / 100 / 2) = 4.88 Tn/m²
X-Passive force = 4.88 * 60.0 / 100 * 1.60 = 4.7 Tn
Z-Passive force = 4.88 * 60.0 / 100 * 2.85 = 8.4 Tn
Friction force = Max (0, 147.1 * 0.45) = 66.2 Tn
1.00 * 4.7 + 1.00 * 66.2

- Sliding safety factor X-X = = = 64.45 > 1.50 OK
1.1
1.00 * 8.4 + 1.00 * 66.2
- Sliding safety factor Z-Z = = = 745.55> 1.50 OK
0.1
0.0 + 6.6 + 3.5 - 0.0

- Uplift safety factor = = = 99.99 > 1.00 OK
0.0
Concrete f'c = 210.0 Kg/cm² Steel fy = 4200.0 Kg/cm² Soil density = 1800 Kg/m³
d Top X-dir = 60.0 - 5.1 - 1.9 / 2 = 53.9 cm
d Top Z-dir = 60.0 - 5.1 - 1.9 - 1.9 / 2 = 52.0 cm
d Bot X-dir = 60.0 - 7.5 - 1.6 / 2 = 51.7 cm
d Bot Z-dir = 60.0 - 7.5 - 1.6 - 1.6 / 2 = 50.1 cm
ϕVcx = 0.53 * 0.75 * √(210) * 1.6 * 100 * 51.7 / 1000 = 47.7 Tn ACI Eq. (22.5.5.1)
ϕVcz = 0.53 * 0.75 * √(210) * 2.9 * 100 * 50.1 / 1000 = 82.3 Tn
- Shear forces calculated as the volume of the bearing pressures under the effective areas:
One-way shear Vux (- Side) = 0.0 Tn < 47.7 Tn OK
One-way shear Vux (+ Side) = 0.0 Tn < 47.7 Tn OK
One-way shear Vuz (- Side) = 17.4 Tn < 82.3 Tn OK
One-way shear Vuz (+ Side) = 17.8 Tn < 82.3 Tn OK
3 of 9
Descrip: Z-3
Plain ϕMnx = 1.33 * 0.60 * √(210) * 2.85 * 60.0² / 6 / 1000 = 19.8 Tn-m ACI Eq. (14.5.2.1a)
Plain ϕMnz = 1.33 * 0.60 * √(210) * 1.60 * 60.0² / 6 / 1000 = 11.1 Tn-m
Use Plain Concrete Flexural Strength at Top

- Top moments calculated as the overburden minus the bearing pressures times the lever arm:
Top moment -Mux (- Side) = 0.0 Tn-m < 19.8 Tn-m OK
Top moment -Mux (+ Side) = 0.0 Tn-m < 19.8 Tn-m OK
Top moment -Muz (- Side) = 0.0 Tn-m < 11.1 Tn-m OK
Top moment -Muz (+ Side) = 0.0 Tn-m < 11.1 Tn-m OK
32.0 / (2.85 * 100 * 50.1) = 0.0022 q = 0.0022 * 4200 / 210.0 = 0.045

20.0 / (1.60 * 100 * 51.7) = 0.0024 q = 0.0024 * 4200 / 210.0 = 0.048
2.85 / 1.60 = 1.78 2 * 1.78 / (1.78 + 1) = 1.28 ACI 13.3.3.3
Bending strength ACI 22.2.2
ϕMnx = 0.90 * 2.85 * 100 * 50.1² * 210.0 * 0.045 * (1 - 0.59 * 0.045) = 46.4 Tn-m
ϕMnz = 0.90 * 1.60 * 100 * 51.7² * 210.0 * 0.048 * (1 - 0.59 * 0.048) = 38.0 Tn-m
- Bottom moments calculated as the bearing minus the overburden pressures times the lever arm:
Bottom moment Mux (- Side) = 26.5 Tn-m < 46.4 Tn-m OK ratio = 0.57
Bottom moment Mux (+ Side) = 26.6 Tn-m < 46.4 Tn-m OK ratio = 0.57
Bottom moment Muz (- Side) = 4.9 Tn-m < 38.0 Tn-m OK ratio = 0.13
Bottom moment Muz (+ Side) = 5.1 Tn-m < 38.0 Tn-m OK ratio = 0.13
X-As min = 0.0018 * 1.60 * 100 * 60.0 = 17.3 cm<
² 20.0 cm² OK ACI 8.6.1.1
Z-As min = 0.0018 * 2.85 * 100 * 60.0 = 30.8 cm²< 32.0 cm² OK ACI 8.6.1.1
X-Cover factor = Min (2.5, (7.5 + 1.59 / 2, 16.1 / 2) / 1.59) = 2.5
Straight ACI Eq. (25.4.2.3a)
X-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.13) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.13 = 15.0 cm ACI 25.4.3
-X Ld provided = 2.85 * 100 / 2 + 0.0 - 210.0 / 2 - 5.1 = 32.4 cm > 30.0 cm OK
+X Ld provided = 2.85 * 100 / 2 - 0.0 - 210.0 / 2 - 5.1 = 32.4 cm > 30.0 cm OK
X-bar spacing = 16.1 cm < Min ( 3 * t, 45.7) = 45.7 cm OK ACI 7.7.2.3
Z-bar spacing = 18.0 cm < Min ( 3 * t, 45.7) = 45.7 cm OK
4 of 9
Descrip: Z-3
Z-Cover factor = Min (2.5, (7.5 + 1.59 / 2, 18.0 / 2) / 1.59) = 2.5

Straight ACI Eq. (12-1)
Z-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.57) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.57 = 15.0 cm ACI 25.4.3
-Z Ld provided = 2.85 * 100 / 2 + 0.0 - 210.0 / 2 - 5.1 = 59.9 cm > 30.0 cm OK
+Z Ld provided = 2.85 * 100 / 2 - 0.0 - 210.0 / 2 - 5.1 = 59.9 cm > 30.0 cm OK
Area 210.0 * 30.0 = 6300.0 cm²

Sx = 30.0 * 210.0² / 6 = 220500.0 cm³
Sz = 210.0 * 30.0² / 6 = 31500.0 cm³
Bearing (200.0 / 6300 + 2.0 * 100 / 220500 + 0.2 * 100 / 31500) * 1000 = 33.3 Kg/cm²
Min edge =
Min edge = Min (2.85 * 100 / 2 - 0.0 - 210.0 / 2, 1.60 * 100 / 2 - 0.0 - 30.0 / 2 = 37.5 cm
Area ACI R22.8.3.2
A2 = Min [2.85 * 100 * 1.6 * 100, (210.0 + 2 * 37.5) * (30.0 + 2 * 37.5)] = 29925.0 cm²
Footing 0.65 * 0.85 * 210.0 * Min [2, √(29925.0 / 6300.0)] = 232.1 Kg/cm²
Footing 0.65 * 64.00 * 4200.0 / 6300.0 = 27.7 Kg/cm² ACI 22.8.3.2
Footing bearing 232.1 + 27.7 = 259.8 Kg/cm² > 33.3 Kg/cm² OK
Column 0.65 * 0.85 * 210.0 = 116.0 Kg/cm²
Column 0.65 * 64.00 * 4200.0 / 6300.0 = 27.7 Kg/cm² ACI 22.8.3.2
Column bearing 116.0 + 27.7 = 143.8 Kg/cm² > 33.3 Kg/cm² OK
Shear friction 0.75 * 64.00 * 4200.0 * 0.6 / 10000 = 121.0 Tn ACI Eq. (22.9.4.2)
Shear Max (1.6, 0.2) = 1.6 Tn < 121.0 Tn OK
Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 / 1.3 * 1.59 * 0.28) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.28 = 15.0 cm ACI 25.4.3
Ld provided = 0.80 * 100 = 80.0 cm > 30.0 cm OK
Ldh provided = 60.00 - 7.5 = 52.5 cm > 15.0 cm OK
5 of 9
Descrip: Z-3
X-Edge = 2.85 * 100 / 2 - 0.0 - 210.0 / 2 = 37.5 cm αsx = 10

Z-Edge = 50.9 / 2 = 25.5 cm αsz = 20
αs = 10 + 20 = 30 Col type = Edge β= 210.0 / 30.0 = 7.00 ACI 22.6.5.2
Perimeter ACI 22.6.4.2
bo = 20 / 10 * (210.0 + 50.9 / 2 + 37.5) + 10 / 10 * (30.0 + 50.9 / 2 + 25.5) = 626.8 cm
Area (210.0 + 50.9 / 2 + 37.5) * (30.0 + 50.9 / 2 + 25.5) = 22085.6 cm²
ϕVc = ACI 22.6.5.2
ϕVc = 0.75 * Min (0.53 * (1 + 2 / 7.00), 0.27 * (30 * 50.9 / 626.8 + 2), 1.0) * √(210) = 7.4 Kg/cm²
Punching force
F = 200.0 + 2.66 * 22085.6 / 10000 - 98.2 = 107.7 Tn
b1 = 210.0 + 50.9 / 2 + 37.5 = 273.0 cm b2 = 30.0 + 50.9 / 2 + 25.5 = 80.9 cm
1
γvx factor = =1- = 0.27
1 + (2/3) √(80.9 / 273.0) ACI Eq. (8.4.4.2.2)
1 ACI Eq. (8.4.2.3.2)
γvz factor = =1- = 0.55
1 + (2/3) √(273.0 / 80.9)
X2z = 273.0² / (2 * 273.0 + 80.9) = 118.9 cm X2x = 80.9 / 2 = 40.5 cm
Jcz = ACI R8.4.4.2.3
Jcz = 273.0 * 50.9³ / 6 + 273.0³ * 50.9 / 6 + 2 * 273.0 * 50.9 * (273.0 / 2 * 118.9)² + 80.9 * 50.9 * 118.9² = 245394081 cm⁴
Jcx = ACI R8.4.4.2.3
Jcx = 80.9 * 50.9³ / 12 + 2 * 273.0 * 50.9 * (80.9 / 2)² = 48627572 cm⁴
Stress due to P = 107.7 / (626.8 * 50.9) * 1000 = 3.4 Kg/cm²
Stress due to Mx = 0.27 * 0.3 * 100 * 40.5 / 48627572 * 1000 = 0.0 Kg/cm²
Stress due to Mz = 0.27 * 3.0 * 100 * 118.9 / 245394081 * 1000 = 0.1 Kg/cm²
Punching stress = 3.4 + 0.0 + 0.1 = 3.5 Kg/cm² < 7.4 Kg/cm² OK
6 of 9
Descrip: Z-3
Concrete f'c = 210.0 Kg/cm² Max. strain = 0.0030

Young's Modulus 15100 * √(210) = 218820 Kg/cm² ACI 19.2.2.1
Rupture 2 * √(210) = 29.0 Kg/cm² ACI Eq. (19.2.3.1)
Steel fy = 4200.0 Kg/cm² Es = 2038903 Kg/cm² ACI 20.2.2.2
, ρ = 0.010 d' = 5.7 cm
As min = 0.01 * 210.0 * 30.0 = 63.00 cm² < 64.00 cm² OK ACI 16.3.4.1
Axial Pu = 200.0 Tn
Shear Vux = 1.6 Tn-m
Shear Vuz = 0.2 Tn-m
Moment Mux = 0.2 Tn-m
Moment Muz = 2.0 Tn-m
Moment Mu = √(0.2² + 2.0²) = 2.0 Tn-m
Rotation angle Arc Tan (2.0 / 0.2) * 180 / π = 84° from X-axis
By trial and error, neutral axis depth 0.32
Strain1 = (0.32 * 24.3 - 185.9) / (0.32 * 24.3) * 0.0030 = -- 0.0054
As d Strain fs fc Fs = As(fs-fc) Ms = Fs(h/2-d) Is = As(h/2-d)²

(cm²) (cm) (Tn/cm²) (Tn/cm²) (Tn) (Tn-m) (cm⁴)
As1 = 2.00 203.8 -0.0063 4.2 0.0 -8.4 8.2 19145.4
As2 = 2.00 185.9 -0.0054 4.2 0.2 -8.4 6.7 12762.8
As3 = 2.00 167.9 -0.0046 4.2 0.2 -8.4 5.2 7669.9
As4 = 2.00 149.9 -0.0038 4.2 0.2 -8.4 3.7 3866.8
As5 = 2.00 132.0 -0.0030 4.2 0.2 -8.4 2.2 1353.5
As6 = 2.00 114.0 -0.0022 4.2 0.2 -8.4 0.7 129.8
As7 = 2.00 96.1 -0.0014 2.8 0.2 -5.6 -0.6 196.0
As8 = 2.00 78.1 -0.0005 1.1 0.2 -2.2 -0.6 1551.9
As9 = 2.00 60.2 0.0003 0.5 0.2 1.1 0.5 4197.5
As10 = 2.00 42.2 0.0011 2.2 0.2 4.1 2.6 8132.9
As11 = 2.00 24.2 0.0019 3.9 0.2 7.4 6.0 13358.0
As12 = 2.00 6.3 0.0027 4.2 0.2 8.0 8.0 19872.9
As13 = 2.00 205.7 -0.0063 4.2 0.2 -8.4 8.4 19872.9
As14 = 2.00 187.7 -0.0055 4.2 0.2 -8.4 6.9 13358.0
As15 = 2.00 169.7 -0.0047 4.2 0.2 -8.4 5.4 8132.9
As16 = 2.00 151.8 -0.0039 4.2 0.2 -8.4 3.8 4197.5
As17 = 2.00 133.8 -0.0031 4.2 0.2 -8.4 2.3 1551.9
As18 = 2.00 115.9 -0.0023 4.2 0.2 -8.4 0.8 196.0
As19 = 2.00 97.9 -0.0014 3.0 0.2 -5.9 -0.5 129.8
As20 = 2.00 80.0 -0.0006 1.3 0.2 -2.6 -0.7 1353.5
7 of 9
Descrip: Z-3
As21 = 2.00 62.0 0.0002 0.4 0.2 0.7 0.3 3866.8

As22 = 2.00 44.0 0.0010 2.0 0.2 3.7 2.3 7669.9
As23 = 2.00 26.1 0.0018 3.7 0.2 7.0 5.6 12762.8
As24 = 2.00 8.1 0.0026 4.2 0.2 8.0 7.9 19145.4
As25 = 2.00 205.3 -0.0063 4.2 0.2 -8.4 8.3 19726.4
As26 = 2.00 204.9 -0.0063 4.2 0.2 -8.4 8.3 19580.3
As27 = 2.00 204.5 -0.0063 4.2 0.2 -8.4 8.3 19434.8
As28 = 2.00 204.2 -0.0063 4.2 0.2 -8.4 8.2 19289.9
As29 = 2.00 7.8 0.0026 4.2 0.0 8.0 7.9 19289.9
As30 = 2.00 7.4 0.0027 4.2 0.0 8.0 7.9 19434.8
As31 = 2.00 7.0 0.0027 4.2 0.0 8.0 8.0 19580.3
As32 = 2.00 6.7 0.0027 4.2 0.0 8.0 8.0 19726.4
T = -78.4 Ms = 150.2 Is = 340537.9
Conc. force Fc = 300.6 Tn
Conc. moment Mc = 230.5 Tn-m
Nominal flexural strength 150.2 + 230.5 = 380.7 Tn-m
ϕ-factor slope =
ϕ-factor slope =(0.65 - 0.90) / (0.65 * 540.4 - 0.9 * 263.4) = -0.0022 ACI 21.2.2
ϕ-factor =
ϕ-factor = Min (0.9, Max (0.65, -0.0022 * (200.0 - 0.9 * 263.4) + 0.9)) = 0.90
Axial strength 0.8 * 0.85 * 210.0 * (6300 - 64.0) + 4200 * 64.0 = 1101.7 Tn
Design flexural strength ϕMn = 0.90 * 380.7 = 342.7 Tn-m ACI 21.2.2
Strength ratio = Max (200.0 / (0.7 * 1101.7), 2.0 / 342.7) = 0.28 < 1.0 OK
Concrete Design .................. ACI 318-14

Load Combinations .............. Pre-combined
9 of 9
Descrip: Z-3
9 of 9
Descrip: Zapata Z-5
Service Factored

Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 0.5 * 0.60 = 0.3 Tn-m

Arm = 1.80 / 2 = 0.90 m Moment = 7.3 * 0.90 = 6.5 Tn-m
Arm = 1.80 / 2 - 0.0 / 100 = 0.90 m Moment = 0.0 * 0.90 = 0.0 Tn-m
- Soil cover = (1.80 * 2.80 - 25.0 / 100 * 180.0 / 100) * 0.5 * 1800 = 4.1 Tn
Arm = 1.80 / 2 = 0.90 m Moment = 4.1 * 0.90 = 3.7 Tn-m
- Buoyancy = 1.80 * 2.80 * 1.0 * (-0.10) = 0.0 Tn
Arm = 1.80 / 2 = 0.90 m Moment = 0.0 * 0.90 = 0.0 Tn-m
Arm = 1.80 / 2 - 0.0 / 100 = 0.90 m Moment = 167.0 * 0.90 = 150.3 Tn-m
160.6
0.7
1 of 9
Descrip: Zapata Z-5

Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 2.6 * 0.60 = 1.6 Tn-m

Arm = 2.80 / 2 = 1.40 m Moment = 7.3 * 1.40 = 10.2 Tn-m
Arm = 2.80 / 2 - 0.0 / 100 = 1.40 m Moment = 0.0 * 1.40 = 0.0 Tn-m
- Soil cover = (1.80 * 2.80 - 25.0 / 100 * 180.0 / 100) * 0.5 * 1800 = 4.1 Tn
Arm = 2.80 / 2 = 1.40 m Moment = 4.1 * 1.40 = 5.8 Tn-m
- Buoyancy = 1.80 * 2.80 * 1.0 * (-0.10) = 0.0 Tn
Arm = 2.80 / 2 = 1.40 m Moment = 0.0 * 1.40 = 0.0 Tn-m
Arm = 2.80 / 2 - 0.0 / 100 = 1.40 m Moment = 167.0 * 1.40 = 233.8 Tn-m
249.8
1.7

249.8 - 1.7
Xp = = = 1.39 m
178.4
160.6 - 0.7
Zp = = = 0.90 m
178.4
X-ecc = 2.80 / 2 - 1.39 = 0.01 m
Z-ecc = 1.80 / 2 - 0.90 = 0.00 m
Area = 1.80 * 2.80 = 5.0 m²
Sx = 2.80 * 1.80² / 6 = 1.5 m³
Sz = 1.80 * 2.80² / 6 = 2.4 m³
P1 = 178.4 * (1 / 5.0 + 0.00 / 1.5 + 0.01 / 2.4) = 36.56 Tn/m²
P2 = 178.4 * (1 / 5.0 - 0.00 / 1.5 + 0.01 / 2.4) = 35.64 Tn/m²
P3 = 178.4 * (1 / 5.0 - 0.00 / 1.5 - 0.01 / 2.4) = 34.23 Tn/m²
P4 = 178.4 * (1 / 5.0 + 0.00 / 1.5 - 0.01 / 2.4) = 35.15 Tn/m² 2 of 9
Descrip: Zapata Z-5

1.00 * 5.3 + 1.00 * 80.3

2.6
1.00 * 8.2 + 1.00 * 80.3
0.5
0.0 + 7.3 + 4.1 - 0.0

0.0
d Top X-dir = 60.0 - 5.1 - 1.9 / 2 = 53.9 cm
d Top Z-dir = 60.0 - 5.1 - 1.9 - 1.9 / 2 = 52.0 cm
d Bot X-dir = 60.0 - 7.5 - 1.6 / 2 = 51.7 cm
d Bot Z-dir = 60.0 - 7.5 - 1.6 - 1.6 / 2 = 50.1 cm
ϕVcx = 0.53 * 0.75 * √(210) * 1.8 * 100 * 51.7 / 1000 = 53.6 Tn ACI Eq. (22.5.5.1)
ϕVcz = 0.53 * 0.75 * √(210) * 2.8 * 100 * 50.1 / 1000 = 80.8 Tn
3 of 9
Descrip: Zapata Z-5
Plain ϕMnz = 1.33 * 0.60 * √(210) * 1.80 * 60.0² / 6 / 1000 = 12.5 Tn-m

32.0 / (2.80 * 100 * 50.1) = 0.0023 q = 0.0023 * 4200 / 210.0 = 0.046

20.0 / (1.80 * 100 * 51.7) = 0.0021 q = 0.0021 * 4200 / 210.0 = 0.043
2.80 / 1.80 = 1.56 2 * 1.56 / (1.56 + 1) = 1.22 ACI 13.3.3.3
ϕMnx = 0.90 * 2.80 * 100 * 50.1² * 210.0 * 0.046 * (1 - 0.59 * 0.046) = 48.7 Tn-m
ϕMnz = 0.90 * 1.80 * 100 * 51.7² * 210.0 * 0.043 * (1 - 0.59 * 0.043) = 38.1 Tn-m
X-As min = 0.0018 * 1.80 * 100 * 60.0 = 19.4 cm<
² 20.0 cm² OK ACI 8.6.1.1
X-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.29) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.29 = 15.0 cm ACI 25.4.3
4 of 9
Descrip: Zapata Z-5

Z-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.85) = 35.7 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.85 = 20.5 cm ACI 25.4.3
Area 180.0 * 25.0 = 4500.0 cm²

Sx = 25.0 * 180.0² / 6 = 135000.0 cm³
Sz = 180.0 * 25.0² / 6 = 18750.0 cm³
Bearing (244.0 / 4500 + 0.1 * 100 / 135000 + 0.6 * 100 / 18750) * 1000 = 57.5 Kg/cm²
Min edge =
Min edge = Min (2.80 * 100 / 2 - 0.0 - 180.0 / 2, 1.80 * 100 / 2 - 0.0 - 25.0 / 2 = 50.0 cm
Area ACI R22.8.3.2
A2 = Min [2.80 * 100 * 1.8 * 100, (180.0 + 2 * 50.0) * (25.0 + 2 * 50.0)] = 35000.0 cm²
Footing 0.65 * 0.85 * 210.0 * Min [2, √(35000.0 / 4500.0)] = 232.1 Kg/cm²
Footing 0.65 * 56.00 * 4200.0 / 4500.0 = 34.0 Kg/cm² ACI 22.8.3.2
Column 0.65 * 0.85 * 210.0 = 116.0 Kg/cm²
Column 0.65 * 56.00 * 4200.0 / 4500.0 = 34.0 Kg/cm² ACI 22.8.3.2
Shear Max (4.0, 0.7) = 4.0 Tn < 105.8 Tn OK
Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 / 1.0 * 1.59 * 0.46) = 49.8 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.46 = 15.0 cm ACI 25.4.3
5 of 9
Descrip: Zapata Z-5
X-Edge = 2.80 * 100 / 2 - 0.0 - 180.0 / 2 = 50.0 cm αsx = 10

Z-Edge = 50.9 / 2 = 25.5 cm αsz = 20
bo = 20 / 10 * (180.0 + 50.9 / 2 + 50.0) + 10 / 10 * (25.0 + 50.9 / 2 + 25.5) = 586.8 cm
Area (180.0 + 50.9 / 2 + 50.0) * (25.0 + 50.9 / 2 + 25.5) = 19392.3 cm²
ϕVc = ACI 22.6.5.2
ϕVc = 0.75 * Min (0.53 * (1 + 2 / 7.20), 0.27 * (30 * 50.9 / 586.8 + 2), 1.0) * √(210) = 7.4 Kg/cm²
Punching force
F = 244.0 + 2.72 * 19392.3 / 10000 - 89.6 = 159.6 Tn
b1 = 180.0 + 50.9 / 2 + 50.0 = 255.5 cm b2 = 25.0 + 50.9 / 2 + 25.5 = 75.9 cm
1
γvx factor = =1- = 0.27
1 + (2/3) √(75.9 / 255.5) ACI Eq. (8.4.4.2.2)
1 ACI Eq. (8.4.2.3.2)
γvz factor = =1- = 0.55
1 + (2/3) √(255.5 / 75.9)
X2z = 255.5² / (2 * 255.5 + 75.9) = 111.2 cm X2x = 75.9 / 2 = 38.0 cm
Jcz = ACI R8.4.4.2.3
Jcz = 255.5 * 50.9³ / 6 + 255.5³ * 50.9 / 6 + 2 * 255.5 * 50.9 * (255.5 / 2 * 111.2)² + 75.9 * 50.9 * 111.2² = 201972203 cm⁴
Jcx = ACI R8.4.4.2.3
Jcx = 75.9 * 50.9³ / 12 + 2 * 255.5 * 50.9 * (75.9 / 2)² = 40165513 cm⁴
6 of 9
Descrip: Zapata Z-5

, ρ = 0.012 d' = 5.7 cm
As min = 0.01 * 180.0 * 25.0 = 45.00 cm² < 56.00 cm² OK ACI 16.3.4.1
Axial Pu = 244.0 Tn
Moment Mu = √(0.6² + 0.1²) = 0.6 Tn-m
Strain1 = (0.57 * 19.3 - 31.2) / (0.57 * 19.3) * 0.0030 = -- 0.0004

As1 = 2.00 34.3 -0.0007 1.5 0.0 -2.9 0.2 103.4
As2 = 2.00 31.2 -0.0004 0.8 0.2 -1.6 0.1 33.8
As3 = 2.00 28.2 -0.0001 0.1 0.2 -0.2 0.0 2.1
As4 = 2.00 25.1 0.0003 0.6 0.2 1.1 0.0 8.4
As5 = 2.00 22.0 0.0006 1.3 0.2 2.2 0.1 52.5
As6 = 2.00 18.9 0.0009 1.9 0.2 3.5 0.3 134.5
As7 = 2.00 15.8 0.0013 2.6 0.2 4.9 0.5 254.4
As8 = 2.00 12.8 0.0016 3.3 0.2 6.2 0.9 412.2
As9 = 2.00 9.7 0.0019 4.0 0.2 7.6 1.3 608.0
As10 = 2.00 6.6 0.0023 4.2 0.2 8.0 1.6 841.6
As11 = 2.00 47.6 -0.0022 4.2 0.2 -8.4 1.7 841.6
As12 = 2.00 44.6 -0.0018 3.7 0.2 -7.5 1.3 608.0
As13 = 2.00 41.5 -0.0015 3.1 0.2 -6.1 0.9 412.2
As14 = 2.00 38.4 -0.0012 2.4 0.2 -4.7 0.5 254.4
As15 = 2.00 35.3 -0.0008 1.7 0.2 -3.4 0.3 134.5
As16 = 2.00 32.2 -0.0005 1.0 0.2 -2.0 0.1 52.5
As17 = 2.00 29.2 -0.0002 0.3 0.2 -0.7 0.0 8.4
As18 = 2.00 26.1 0.0002 0.3 0.2 0.7 0.0 2.1
As19 = 2.00 23.0 0.0005 1.0 0.2 1.7 0.1 33.8
As20 = 2.00 19.9 0.0008 1.7 0.2 3.1 0.2 103.4
7 of 9
Descrip: Zapata Z-5
As21 = 2.00 45.0 -0.0019 3.8 0.2 -7.6 1.4 637.1

As22 = 2.00 42.3 -0.0016 3.2 0.2 -6.5 1.0 461.1
As23 = 2.00 39.6 -0.0013 2.6 0.2 -5.3 0.7 313.4
As24 = 2.00 37.0 -0.0010 2.1 0.2 -4.1 0.4 194.2
As25 = 2.00 17.3 0.0011 2.3 0.2 4.2 0.4 194.2
As26 = 2.00 14.6 0.0014 2.9 0.2 5.4 0.7 313.4
As27 = 2.00 11.9 0.0017 3.5 0.2 6.6 1.0 461.1
As28 = 2.00 9.3 0.0020 4.1 0.2 7.8 1.4 637.1
T = 2.0 Ms = 17.1 Is = 8113.5
ϕ-factor slope =
ϕ-factor =
ϕ-factor = Min (0.9, Max (0.65, -0.0023 * (244.0 - 0.9 * 143.4) + 0.9)) = 0.65

9 of 9
Descrip: Zapata Z-5
9 of 9
Descrip: Z-8
Service Factored

Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 0.1 * 0.60 = 0.1 Tn-m

Arm = 1.40 / 2 = 0.70 m Moment = 4.4 * 0.70 = 3.1 Tn-m
Arm = 1.40 / 2 - 0.0 / 100 = 0.70 m Moment = 0.0 * 0.70 = 0.0 Tn-m
- Soil cover = (1.40 * 2.20 - 40.0 / 100 * 100.0 / 100) * 0.5 * 1800 = 2.4 Tn
Arm = 1.40 / 2 = 0.70 m Moment = 2.4 * 0.70 = 1.7 Tn-m
- Buoyancy = 1.40 * 2.20 * 1.0 * (-0.10) = 0.0 Tn
Arm = 1.40 / 2 = 0.70 m Moment = 0.0 * 0.70 = 0.0 Tn-m
Arm = 1.40 / 2 - 0.0 / 100 = 0.70 m Moment = 59.0 * 0.70 = 41.3 Tn-m
46.1
0.2
1 of 9
Descrip: Z-8

Arm = 0.00 + 60.0 / 100 = 0.60 m Moment = 2.5 * 0.60 = 1.5 Tn-m

Arm = 2.20 / 2 = 1.10 m Moment = 4.4 * 1.10 = 4.9 Tn-m
Arm = 2.20 / 2 - 0.0 / 100 = 1.10 m Moment = 0.0 * 1.10 = 0.0 Tn-m
- Soil cover = (1.40 * 2.20 - 40.0 / 100 * 100.0 / 100) * 0.5 * 1800 = 2.4 Tn
Arm = 2.20 / 2 = 1.10 m Moment = 2.4 * 1.10 = 2.7 Tn-m
- Buoyancy = 1.40 * 2.20 * 1.0 * (-0.10) = 0.0 Tn
Arm = 2.20 / 2 = 1.10 m Moment = 0.0 * 1.10 = 0.0 Tn-m
Arm = 2.20 / 2 - 0.0 / 100 = 1.10 m Moment = 59.0 * 1.10 = 64.9 Tn-m
72.4
6.5

72.4 - 6.5
Xp = = = 1.00 m
65.9
46.1 - 0.2
Zp = = = 0.70 m
65.9
X-ecc = 2.20 / 2 - 1.00 = 0.10 m
Z-ecc = 1.40 / 2 - 0.70 = 0.00 m
Area = 1.40 * 2.20 = 3.1 m²
Sx = 2.20 * 1.40² / 6 = 0.7 m³
Sz = 1.40 * 2.20² / 6 = 1.1 m³
P1 = 65.9 * (1 / 3.1 + 0.00 / 0.7 + 0.10 / 1.1) = 27.36 Tn/m²
P2 = 65.9 * (1 / 3.1 - 0.00 / 0.7 + 0.10 / 1.1) = 26.92 Tn/m²
P3 = 65.9 * (1 / 3.1 - 0.00 / 0.7 - 0.10 / 1.1) = 15.41 Tn/m²
P4 = 65.9 * (1 / 3.1 + 0.00 / 0.7 - 0.10 / 1.1) = 15.85 Tn/m² 2 of 9
Descrip: Z-8

1.00 * 4.1 + 1.00 * 29.6

2.5
1.00 * 6.4 + 1.00 * 29.6
0.1
0.0 + 4.4 + 2.4 - 0.0

0.0
d Top X-dir = 60.0 - 5.1 - 1.9 / 2 = 53.9 cm
d Top Z-dir = 60.0 - 5.1 - 1.9 - 1.9 / 2 = 52.0 cm
d Bot X-dir = 60.0 - 7.6 - 1.6 / 2 = 51.6 cm
d Bot Z-dir = 60.0 - 7.6 - 1.6 - 1.6 / 2 = 50.0 cm
ϕVcx = 0.53 * 0.75 * √(210) * 1.4 * 100 * 51.6 / 1000 = 41.6 Tn ACI Eq. (22.5.5.1)
ϕVcz = 0.53 * 0.75 * √(210) * 2.2 * 100 * 50.0 / 1000 = 63.4 Tn
3 of 9
Descrip: Z-8
Plain ϕMnz = 1.33 * 0.60 * √(210) * 1.40 * 60.0² / 6 / 1000 = 9.7 Tn-m

32.0 / (2.20 * 100 * 50.0) = 0.0029 q = 0.0029 * 4200 / 210.0 = 0.058

20.0 / (1.40 * 100 * 51.6) = 0.0028 q = 0.0028 * 4200 / 210.0 = 0.055
2.20 / 1.40 = 1.57 2 * 1.57 / (1.57 + 1) = 1.22 ACI 13.3.3.3
ϕMnx = 0.90 * 2.20 * 100 * 50.0² * 210.0 * 0.058 * (1 - 0.59 * 0.058) = 48.1 Tn-m
ϕMnz = 0.90 * 1.40 * 100 * 51.6² * 210.0 * 0.055 * (1 - 0.59 * 0.055) = 37.7 Tn-m
X-As min = 0.0018 * 1.40 * 100 * 60.0 = 15.1 cm<
² 20.0 cm² OK ACI 8.6.1.1
X-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.23) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.23 = 15.0 cm ACI 25.4.3
4 of 9
Descrip: Z-8

Z-Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 * 1.0 / 2.5 * 1.59 * 0.16) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.16 = 15.0 cm ACI 25.4.3
Area 100.0 * 40.0 = 4000.0 cm²

Sx = 40.0 * 100.0² / 6 = 66666.7 cm³
Sz = 100.0 * 40.0² / 6 = 26666.7 cm³
Bearing (85.0 / 4000 + 7.0 * 100 / 66667 + 0.1 * 100 / 26667) * 1000 = 32.1 Kg/cm²
Min edge =
Min edge = Min (2.20 * 100 / 2 - 0.0 - 100.0 / 2, 1.40 * 100 / 2 - 0.0 - 40.0 / 2 = 50.0 cm
Area ACI R22.8.3.2
A2 = Min [2.20 * 100 * 1.4 * 100, (100.0 + 2 * 50.0) * (40.0 + 2 * 50.0)] = 28000.0 cm²
Footing 0.65 * 0.85 * 210.0 * Min [2, √(28000.0 / 4000.0)] = 232.1 Kg/cm²
Footing 0.65 * 56.00 * 4200.0 / 4000.0 = 38.2 Kg/cm² ACI 22.8.3.2
Column 0.65 * 0.85 * 210.0 = 116.0 Kg/cm²
Column 0.65 * 56.00 * 4200.0 / 4000.0 = 38.2 Kg/cm² ACI 22.8.3.2
Shear Max (4.0, 0.1) = 4.0 Tn < 105.8 Tn OK
Ld = Max (30.0, 4200.0 / 3.5 / (210)½ * 0.8 / 1.9 * 1.59 * 0.18) = 30.0 cm
Hooked 0.075 * 4200.0 / (210.0)½ * 1.59 * 0.7 * 0.18 = 15.0 cm ACI 25.4.3
5 of 9
Descrip: Z-8
X-Edge = 50.8 / 2 = 25.4 cm αsx = 20

Z-Edge = 1.40 * 100 / 2 - 0.0 - 40.0 / 2 = 50.0 cm αsz = 10
bo = 10 / 10 * (100.0 + 50.8 / 2 + 25.4) + 20 / 10 * (40.0 + 50.8 / 2 + 50.0) = 381.6 cm
Area (100.0 + 50.8 / 2 + 25.4) * (40.0 + 50.8 / 2 + 50.0) = 17404.7 cm²
ϕVc = ACI 22.6.5.2
ϕVc = 0.75 * Min (0.53 * (1 + 2 / 2.50), 0.27 * (30 * 50.8 / 381.6 + 2), 1.0) * √(210) = 10.4 Kg/cm²
Punching force
F = 85.0 + 2.67 * 17404.7 / 10000 - 41.5 = 48.2 Tn
b1 = 100.0 + 50.8 / 2 + 25.4 = 150.8 cm b2 = 40.0 + 50.8 / 2 + 50.0 = 115.4 cm
1
γvx factor = =1- = 0.37
1 + (2/3) √(115.4 / 150.8) ACI Eq. (8.4.4.2.2)
1 ACI Eq. (8.4.2.3.2)
γvz factor = =1- = 0.43
1 + (2/3) √(150.8 / 115.4)
X2z = 150.8 / 2 = 75.4 cm X2x = 115.4² / (2 * 115.4 + 150.8) = 34.9 cm
Jcz = ACI R8.4.4.2.3
Jcx = 150.8 * 50.8³ / 12 + 2 * 115.4 * 50.8 * (150.8 / 2)² = 82860825 cm⁴
Jcx = ACI R8.4.4.2.3
Jcz = 115.4 * 50.8³ / 6 + 115.4³ * 50.8 / 6 + 2 * 115.4 * 50.8 * (115.4 / 2 * 34.9)² + 150.8 * 50.8 * 34.9² = 30972557 cm⁴
6 of 9
Descrip: Z-8

, ρ = 0.014 d' = 5.7 cm
As min = 0.01 * 100.0 * 40.0 = 40.00 cm² < 56.00 cm² OK ACI 16.3.4.1
Axial Pu = 85.0 Tn
Moment Mu = √(0.1² + 7.0²) = 7.0 Tn-m
Strain1 = (0.29 * 34.3 - 84.5) / (0.29 * 34.3) * 0.0030 = -- 0.0063

As1 = 2.00 94.3 -0.0074 4.2 0.0 -8.4 3.7 3880.0
As2 = 2.00 84.5 -0.0063 4.2 0.2 -8.4 2.9 2341.0
As3 = 2.00 74.7 -0.0052 4.2 0.2 -8.4 2.0 1188.7
As4 = 2.00 64.8 -0.0041 4.2 0.2 -8.4 1.2 423.2
As5 = 2.00 55.0 -0.0030 4.2 0.2 -8.4 0.4 44.4
As6 = 2.00 45.2 -0.0020 4.0 0.2 -8.0 -0.4 52.4
As7 = 2.00 35.3 -0.0009 1.8 0.2 -3.6 -0.5 447.2
As8 = 2.00 25.5 0.0002 0.4 0.2 0.8 0.2 1228.7
As9 = 2.00 15.7 0.0013 2.6 0.2 4.9 1.7 2397.0
As10 = 2.00 5.8 0.0024 4.2 0.2 8.0 3.6 3952.1
As11 = 2.00 94.7 -0.0074 4.2 0.2 -8.4 3.7 3952.1
As12 = 2.00 84.9 -0.0063 4.2 0.2 -8.4 2.9 2397.0
As13 = 2.00 75.1 -0.0052 4.2 0.2 -8.4 2.1 1228.7
As14 = 2.00 65.2 -0.0042 4.2 0.2 -8.4 1.3 447.2
As15 = 2.00 55.4 -0.0031 4.2 0.2 -8.4 0.4 52.4
As16 = 2.00 45.6 -0.0020 4.1 0.2 -8.2 -0.4 44.4
As17 = 2.00 35.7 -0.0009 1.9 0.2 -3.8 -0.5 423.2
As18 = 2.00 25.9 0.0002 0.3 0.2 0.6 0.2 1188.7
As19 = 2.00 16.1 0.0012 2.5 0.2 4.7 1.6 2341.0
As20 = 2.00 6.2 0.0023 4.2 0.2 8.0 3.5 3880.0
7 of 9
Descrip: Z-8
As21 = 2.00 94.7 -0.0074 4.2 0.2 -8.4 3.7 3937.6

As22 = 2.00 94.6 -0.0074 4.2 0.2 -8.4 3.7 3923.2
As23 = 2.00 94.5 -0.0074 4.2 0.2 -8.4 3.7 3908.8
As24 = 2.00 94.4 -0.0074 4.2 0.2 -8.4 3.7 3894.4
As25 = 2.00 6.2 0.0023 4.2 0.2 8.0 3.5 3894.4
As26 = 2.00 6.1 0.0023 4.2 0.0 8.0 3.6 3908.8
As27 = 2.00 6.0 0.0023 4.2 0.0 8.0 3.6 3923.2
As28 = 2.00 5.9 0.0024 4.2 0.0 8.0 3.6 3937.6
T = -81.8 Ms = 58.6 Is = 63237.6
ϕ-factor slope =
ϕ-factor =
ϕ-factor = Min (0.9, Max (0.65, -0.0032 * (85.0 - 0.9 * 169.4) + 0.9)) = 0.90

9 of 9
Descrip: Z-8
9 of 9
7.1.2 Diseño de los Muros de contención. Usando el Programa de Midas Set
Diseño de Corte 1:
_________________________________________________________________________________________

_________________________________________________________________________________________

Diseño de Corte 6:
_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

7.1.3 Diseño de losas aligeradas. Usando el Programa IP3 Losas
Techo Semisótano:
Losa Aligerada de H = 20 cm Tabiquería 100 kg/m2 S/C = 200 kg/m2
_________________________________________________________________________________________

_________________________________________________________________________________________

Losa Aligerada de H = 20 cm Tabiquería 100 kg/m2 S/C = 200 kg/m2
_________________________________________________________________________________________

_________________________________________________________________________________________

7.1.5 Diseño de Vigas. Usando el Programa Staad Pró
Techo de Semisótano
_________________________________________________________________________________________

Sunday, August 14, 2022, 09:50 PM
STAAD SPACE -- PAGE NO. 33
ACI 318-11 BEAM NO. 81 DESIGN RESULTS

=============================================
LEN - 1830. MM FY - 414. FC - 21. MPA, SIZE - 250. X 550. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________
1 498. 4 - 12MM 0. 1830. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 61.29 KN-MET AT 1830.MM, LOAD 20|
| REQD STEEL= 415.MM2, RHO=0.0033, RHOMX=0.0160 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 266./ 37./ 49. MMS |
| REQD. DEVELOPMENT LENGTH = 488. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 74402.2 cm^4
REQUIRED REINF. STEEL SUMMARY :

-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 0./ 150. 0./ 27. 0/ 16

152. 0./ 143. 0./ 26. 0/ 16
305. 0./ 140. 0./ 25. 0/ 16
457. 0./ 140. 0./ 25. 0/ 16
610. 0./ 144. 0./ 26. 0/ 16
762. 0./ 151. 0./ 27. 0/ 16
915. 0./ 164. 0./ 29. 0/ 20
1067. 0./ 183. 0./ 33. 0/ 20
1220. 0./ 208. 0./ 37. 0/ 20
1372. 0./ 236. 0./ 42. 0/ 20
1525. 0./ 269. 0./ 48. 0/ 20
1677. 0./ 306. 0./ 54. 0/ 20
1830. 0./ 348. 0./ 61. 0/ 20
B E A M N O. 81 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 7.39 KNS Vc= 89.12 KNS Vs= 0.00 KNS
Tu= 11.36 KN-MET Tc= 3.3 KN-MET Ts= 15.1 KN-MET LOAD 20
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 8 MM 2-LEGGED STIRRUPS AT 158. MM C/C FOR 419. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 3.52 SQ.CM.
C:\Users\Secretearia\Desktop\Modelo Trinidad Moran\Edificio Trinidad 08 Ago 22.anl Page 33 of 53

AT END SUPPORT - Vu= 33.70 KNS Vc= 89.12 KNS Vs= 0.00 KNS
___ 10J____________________ 1829X 250X 550_____________________ 57J____

| |
||=========================================================================||
| 4No12 H 498. 0.TO 1830 |
| 4*8 c/c158 4*8 c/c158 |
| |
| |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oooo | | oooo | | oooo | | oooo | | oooo | | oooo | | oooo |
| 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 3 - 16MM 257. 4573. NO NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 87.11 KN-MET AT 2300.MM, LOAD 20|
|----------------------------------------------------------------|
2 498. 4 - 12MM 0. 974. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|

3 491. 2 - 25MM 3267. 5520. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 419. 0./ 73. 0/ 20

460. 0./ 106. 0./ 19. 0/ 18
920. 137./ 0. 25./ 0. 20/ 0
1380. 321./ 0. 57./ 0. 20/ 0
1840. 444./ 0. 78./ 0. 20/ 0
2300. 502./ 0. 87./ 0. 20/ 0
2760. 492./ 0. 85./ 0. 20/ 0
3220. 414./ 0. 72./ 0. 20/ 0
3680. 272./ 0. 48./ 0. 20/ 0
4140. 74./ 0. 13./ 0. 19/ 0
4600. 0./ 190. 0./ 34. 0/ 20
5060. 0./ 532. 0./ 92. 0/ 20
5520. 0./ 977. 0./ 161. 0/ 20
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.

___ 57J____________________ 5520X 250X 550_____________________ 162J____

| |
||============ ===============================||
| 4No12 H 498. 0.TO 974 2No25|H 491.3267.TO 5520 |
| 11*8 c/c248 | | | | 11*8 c/c238 |
| 3No16 H 54. 257.TO 4573 | | | | | |
| ============================================================ |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oooo | | oooo | | | | | | oo | | oo | | oo |
| 4#12 | | 4#12 | | | | | | 2#25 | | 2#25 | | 2#25 |
| | | | | | | | | | | | | |
| | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | | | |
| | | ooo | | ooo | | ooo | | ooo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 3 - 12MM 345. 5022. NO NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 496. 2 - 16MM 0. 1618. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
3 498. 4 - 12MM 3453. 5600. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 287. 0./ 51. 0/ 20

467. 0./ 140. 0./ 25. 0/ 16
933. 49./ 30. 9./ 6. 17/ 21
1400. 134./ 0. 24./ 0. 17/ 0
1867. 194./ 0. 35./ 0. 17/ 0
2333. 227./ 0. 40./ 0. 17/ 0
2800. 233./ 0. 42./ 0. 17/ 0
3267. 213./ 0. 38./ 0. 17/ 0
3733. 166./ 0. 30./ 0. 17/ 0
4200. 93./ 2. 17./ 0. 17/ 21
4667. 13./ 70. 2./ 13. 22/ 16
5133. 0./ 194. 0./ 35. 0/ 16
5600. 0./ 376. 0./ 66. 0/ 20

___ 163J____________________ 5600X 250X 550_____________________ 164J____

| |
||==================== =============================||
| 2No16 H 496.| 0.TO 1618 |4No12 H|498.3453.TO|5600 |
| 11*8 c/c249 | | | | | | 11*8 c/c249 |
| 3No12|H 52. 345.TO 5022 | | | | | | |
| ================================================================= |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | | | | | oooo | | oooo | | oooo |
| 2#16 | | 2#16 | | | | | | 4#12 | | 4#12 | | 4#12 |
| | | | | | | | | | | | | |
| | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 4 - 12MM 502. 4150. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 496. 4 - 16MM 0. 2633. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 0./ 796. 0./ 134. 0/ 16

346. 0./ 587. 0./ 101. 0/ 16
692. 0./ 405. 0./ 71. 0/ 16
1038. 11./ 249. 2./ 44. 22/ 16
1383. 66./ 115. 12./ 21. 22/ 16
1729. 147./ 36. 26./ 6. 17/ 21
2075. 226./ 0. 40./ 0. 17/ 0
2421. 289./ 0. 51./ 0. 17/ 0
2767. 337./ 0. 59./ 0. 20/ 0
3112. 379./ 0. 67./ 0. 20/ 0
3458. 400./ 0. 70./ 0. 20/ 0
3804. 398./ 0. 70./ 0. 20/ 0
4150. 374./ 0. 66./ 0. 20/ 0
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.

___ 12J____________________ 4150X 250X 550_____________________ 146J____

| |
||=============================================== |
| 4No16 H 496.| 0.TO 2633| | | | | | | |
| 12*8 c/c158 | | | | | | | | | | | 12*8 c/c158 |
| 4No12 H| 52. 502.TO|4150 | | | | |
| ==================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oooo | | oooo | | oooo | | oooo | | | | | | |
| 4#16 | | 4#16 | | 4#16 | | 4#16 | | | | | | |
| | | | | | | | | | | | | |
| | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 |
| | | oooo | | oooo | | oooo | | oooo | | oooo | | oooo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 4 - 12MM 0. 2763. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 494. 3 - 20MM 212. 3200. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 383./ 0. 67./ 0. 20/ 0

267. 358./ 0. 63./ 0. 20/ 0
533. 321./ 0. 57./ 0. 20/ 0
800. 276./ 0. 49./ 0. 17/ 0
1067. 237./ 0. 42./ 0. 17/ 0
1333. 187./ 12. 34./ 2. 17/ 21
1600. 128./ 62. 23./ 11. 17/ 21
1867. 77./ 138. 14./ 25. 22/ 16
2133. 42./ 246. 8./ 44. 22/ 16
2400. 1./ 367. 0./ 65. 22/ 16
2667. 0./ 504. 0./ 87. 0/ 16
2933. 0./ 656. 0./ 112. 0/ 16
3200. 0./ 826. 0./ 139. 0/ 17

___ 146J____________________ 3200X 250X 550_____________________ 164J____

| |
| ======================================================================||
| 3No20 H 494.|212.TO 3200| | | | | | |
| 8*8 c/c158 | | | | | | | | | 8*8 c/c158 |
| 4No12 H |52.| 0.TO 2763| | | | | | | |
||================================================================ |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | 3#20 | | 3#20 | | 3#20 | | 3#20 | | 3#20 | | 3#20 |
| | | | | | | | | | | | | |
| 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | 4#12 | | |
| oooo | | oooo | | oooo | | oooo | | oooo | | oooo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 800. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 2 - 12MM 0. 800. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 0./ 138. 0./ 25. 0/ 16

67. 0./ 126. 0./ 23. 0/ 16
133. 2./ 113. 0./ 20. 22/ 16
200. 7./ 100. 1./ 18. 22/ 16
267. 12./ 87. 2./ 16. 22/ 16
333. 17./ 75. 3./ 14. 22/ 16
400. 22./ 63. 4./ 11. 22/ 16
467. 26./ 50. 5./ 9. 22/ 16
533. 31./ 38. 6./ 7. 22/ 16
600. 38./ 28. 7./ 5. 17/ 21
667. 48./ 22. 9./ 4. 17/ 21
733. 57./ 15. 10./ 3. 17/ 21
800. 67./ 8. 12./ 2. 16/ 22
** LOCATION FOR DESIGN FOR SHEAR AT START OF MEMBER 303 IS BEYOND

THE MIDPOINT OF MEMBER. DESIGN FOR SHEAR AND TORSION NOT PERFORMED.
** LOCATION FOR DESIGN FOR SHEAR AT END OF MEMBER 303 IS BEYOND

___ 164J____________________ 800X 250X 550_____________________ 173J____

| |
||=========================================================================||
| 2No12 H 498. 0.TO 800 |
| |
| 2No12 H 52. 0.TO 800 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|


=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 800. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 2 - 12MM 0. 800. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 74. 0./ 13. 22/ 16

67. 3./ 68. 1./ 12. 22/ 16
133. 6./ 62. 1./ 11. 22/ 16
200. 8./ 56. 2./ 10. 22/ 16
267. 11./ 50. 2./ 9. 22/ 16
333. 14./ 44. 2./ 8. 22/ 16
400. 16./ 38. 3./ 7. 22/ 16
467. 18./ 33. 3./ 6. 22/ 16
533. 21./ 27. 4./ 5. 22/ 16
600. 24./ 23. 4./ 4. 17/ 21
667. 28./ 20. 5./ 4. 17/ 21
733. 33./ 17. 6./ 3. 17/ 21
800. 37./ 15. 7./ 3. 16/ 22



___ 173J____________________ 800X 250X 550_____________________ 237J____

| |
||=========================================================================||
| 2No12 H 498. 0.TO 800 |
| |
| 2No12 H 52. 0.TO 800 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 3 - 12MM 0. 3400. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 496. 2 - 16MM 0. 3400. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 239./ 267. 43./ 47. 22/ 16

283. 234./ 246. 42./ 44. 22/ 16
567. 228./ 228. 41./ 41. 22/ 16
850. 220./ 211. 39./ 38. 13/ 16
1133. 212./ 196. 38./ 35. 17/ 21
1417. 202./ 184. 36./ 33. 17/ 21
1700. 190./ 173. 34./ 31. 17/ 21
1983. 177./ 163. 32./ 29. 17/ 21
2267. 162./ 155. 29./ 28. 13/ 16
2550. 147./ 149. 26./ 27. 22/ 16
2833. 130./ 145. 23./ 26. 22/ 16
3117. 112./ 144. 20./ 26. 22/ 16
3400. 93./ 143. 17./ 26. 21/ 17
STIRRUPS ARE NOT REQUIRED.

___ 237J____________________ 3400X 250X 550_____________________ 220J____

| |
||=========================================================================||
| 2No16 H 496. 0.TO 3400 |
| |
| 3No12 H 52. 0.TO 3400 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 | | 3#12 |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 2570. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 2 - 12MM 0. 2570. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 40./ 46. 7./ 8. 17/ 21

214. 43./ 46. 8./ 8. 17/ 21
428. 46./ 47. 8./ 9. 17/ 21
642. 48./ 49. 9./ 9. 22/ 16
857. 50./ 52. 9./ 9. 22/ 16
1071. 51./ 56. 9./ 10. 22/ 16
1285. 52./ 60. 9./ 11. 22/ 16
1499. 52./ 66. 9./ 12. 22/ 16
1713. 52./ 72. 9./ 13. 22/ 16
1928. 51./ 80. 9./ 14. 22/ 16
2142. 49./ 88. 9./ 16. 22/ 16
2356. 47./ 97. 9./ 17. 22/ 16
2570. 44./ 106. 8./ 19. 21/ 17
___ 54J____________________ 2570X 200X 550_____________________ 55J____

| |
||=========================================================================||
| 2No12 H 498. 0.TO 2570 |
| |
| 2No12 H 52. 0.TO 2570 |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12|
| | | | | | | | | | | | | |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12|
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|


=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 1229. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 2 - 12MM 0. 1780. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 83./ 0. 15./ 0. 17/ 0

148. 71./ 0. 13./ 0. 17/ 0
297. 58./ 0. 10./ 0. 17/ 0
445. 44./ 3. 8./ 1. 17/ 21
593. 30./ 10. 6./ 2. 17/ 21
742. 17./ 19. 3./ 3. 22/ 16
890. 10./ 34. 2./ 6. 22/ 16
1038. 2./ 49. 0./ 9. 22/ 16
1187. 0./ 65. 0./ 12. 0/ 16
1335. 0./ 81. 0./ 15. 0/ 16
1483. 0./ 97. 0./ 18. 0/ 16
1632. 0./ 114. 0./ 21. 0/ 16
1780. 0./ 134. 0./ 24. 0/ 20

___ 55J____________________ 1779X 200X 550_____________________ 56J____

| |
||=========================================================================||
| 2No12 H 498. 0.TO 1780 |
| |
| 2No12 H 52. 0.TO 1229 |
||=================================================== |
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | |
| | | | | | | | | | | | | |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 563. 850. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 491. 2 - 25MM 0. 850. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 858. 0./ 140. 0/ 20

71. 0./ 770. 0./ 127. 0/ 20
142. 0./ 683. 0./ 114. 0/ 20
213. 0./ 599. 0./ 101. 0/ 20
283. 0./ 517. 0./ 88. 0/ 20
354. 0./ 437. 0./ 76. 0/ 20
425. 0./ 359. 0./ 63. 0/ 20
496. 0./ 283. 0./ 50. 0/ 20
567. 0./ 208. 0./ 37. 0/ 20
638. 0./ 134. 0./ 24. 0/ 20
708. 0./ 62. 0./ 11. 0/ 20
779. 14./ 3. 2./ 1. 19/ 23
850. 79./ 0. 14./ 0. 20/ 0



___ 56J____________________ 850X 200X 550_____________________ 57J____

| |
||=========================================================================||
| 2No25 H 491. 0.TO 850 |
| |
| 2No12 H 52. 563.TO 850 |
| =========================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#25| | 2#25| | 2#25| | 2#25| | 2#25| | 2#25| | 2#25|
| | | | | | | | | | | | | |
| | | | | | | | | 2#12| | 2#12| | 2#12|
| | | | | | | | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|
********************END OF BEAM DESIGN**************************
522. *DESIGN COLUMN

523. *DESIGN ELEMENT
524. END CONCRETE DESIGN
525. FINISH
*********** END OF THE STAAD.Pro RUN ***********
**** DATE= AUG 14,2022 TIME= 21:48:24 ****

7.1.5 Diseño de Vigas. Usando el Programa Staad Pró
Techo de 1º al 5º piso
_________________________________________________________________________________________

Monday, August 15, 2022, 07:14 AM

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 1423. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 496. 4 - 16MM 0. 1730. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 50./ 726. 9./ 123. 22/ 16

144. 54./ 657. 10./ 112. 22/ 16
288. 55./ 593. 10./ 102. 22/ 16
432. 54./ 534. 10./ 92. 22/ 16
577. 51./ 480. 9./ 83. 22/ 16
721. 46./ 431. 8./ 75. 22/ 16
865. 39./ 386. 7./ 68. 22/ 16
1009. 31./ 345. 6./ 61. 22/ 16
1153. 20./ 309. 4./ 55. 22/ 16
1298. 7./ 277. 1./ 49. 22/ 16
1442. 0./ 248. 0./ 44. 0/ 16
1586. 0./ 224. 0./ 40. 0/ 16
1730. 0./ 204. 0./ 36. 0/ 17

___ 17J____________________ 1729X 250X 550_____________________ 60J____

| |
||=========================================================================||
| 4No16 H|496. |0.TO 1730 | | |
| 4*10c/c158 | | | | 4*10c/c158 |
| 2No12 H| 52. |0.TO 1423 | | |
||============================================================= |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 |
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 4 - 16MM 0. 2450. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

*** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED.

REQD. STEEL = 1900. MM2, MAX. STEEL PERMISSIBLE = 1954. MM2
MAX NEG MOMENT = 282.81 KN-MET, LOADING 16

-------------------------------
0. 0./ 1900. 0./ 283. 0/ 16

204. 0./ 1564. 0./ 242. 0/ 16
408. 46./ 1272. 8./ 203. 22/ 16
612. 111./ 1014. 20./ 167. 22/ 16
817. 169./ 785. 30./ 132. 22/ 16
1021. 223./ 581. 40./ 100. 22/ 16
1225. 270./ 397. 48./ 70. 22/ 16
1429. 334./ 255. 59./ 45. 17/ 21
1633. 423./ 158. 74./ 28. 17/ 21
1838. 501./ 68. 87./ 12. 17/ 21
2042. 568./ 0. 98./ 0. 17/ 0
2246. 622./ 0. 107./ 0. 17/ 0
2450. 664./ 0. 113./ 0. 16/ 0
___ 18J____________________ 2450X 250X 550_____________________ 77J____

| |
| |
| |
| |
| 4No16 H 54. 0.TO 2450 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|


=============================================

_____________________________________________________________________
1 52. 6 - 12MM 0. 2770. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 494. 4 - 20MM 0. 2770. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 558./ 1107. 97./ 184. 22/ 16

231. 589./ 1007. 102./ 169. 22/ 16
462. 615./ 920. 107./ 155. 22/ 16
692. 636./ 844. 110./ 143. 22/ 16
923. 651./ 779. 112./ 133. 22/ 16
1154. 661./ 725. 114./ 125. 22/ 16
1385. 665./ 682. 115./ 117. 22/ 16
1616. 669./ 653. 115./ 113. 17/ 21
1847. 668./ 635. 115./ 110. 17/ 21
2078. 658./ 623. 114./ 108. 17/ 21
2308. 637./ 616. 110./ 107. 17/ 21
2539. 607./ 614. 105./ 106. 22/ 12
2770. 580./ 630. 101./ 109. 21/ 17

___ 19J____________________ 2770X 300X 550_____________________ 93J____

| |
||=========================================================================||
| 4No20|H 494. 0.TO 2770 | | | | | | | | | |
| 7*8 c/c170 | | | | | | | | 7*8 c/c170 | |
| 6No12|H 52. 0.TO 2770 | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| 4#20 | | 4#20 | | 4#20 | | 4#20 | | 4#20 | | 4#20 | | 4#20 |
| | | | | | | | | | | | | |
| 6#12 | | 6#12 | | 6#12 | | 6#12 | | 6#12 | | 6#12 | | 6#12 |
|oooooo | |oooooo | |oooooo | |oooooo | |oooooo | |oooooo | |oooooo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 720. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

2 496. 2 - 16MM 0. 720. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 279. 0./ 50. 0/ 16

60. 0./ 244. 0./ 43. 0/ 16
120. 0./ 209. 0./ 37. 0/ 16
180. 0./ 176. 0./ 32. 0/ 16
240. 5./ 143. 1./ 26. 22/ 16
300. 19./ 111. 3./ 20. 22/ 16
360. 32./ 80. 6./ 15. 22/ 16
420. 45./ 50. 8./ 9. 22/ 16
480. 66./ 29. 12./ 5. 17/ 21
540. 90./ 12. 16./ 2. 17/ 21
600. 113./ 0. 20./ 0. 17/ 0
660. 136./ 0. 25./ 0. 17/ 0
720. 159./ 0. 29./ 0. 16/ 0



___ 60J____________________ 720X 250X 550_____________________ 75J____

| |
||=========================================================================||
| 2No16 H 496. 0.TO 720 |
| |
| 2No12 H 52. 0.TO 720 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 4 - 16MM 0. 220. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 659./ 0. 112./ 0. 17/ 0

18. 661./ 0. 113./ 0. 17/ 0
37. 663./ 0. 113./ 0. 17/ 0
55. 664./ 0. 113./ 0. 17/ 0
73. 666./ 0. 114./ 0. 17/ 0
92. 668./ 0. 114./ 0. 17/ 0
110. 670./ 0. 114./ 0. 17/ 0
128. 671./ 0. 114./ 0. 17/ 0

147. 673./ 0. 115./ 0. 17/ 0

165. 674./ 0. 115./ 0. 17/ 0
183. 675./ 0. 115./ 0. 17/ 0
202. 677./ 0. 115./ 0. 17/ 0
220. 678./ 0. 115./ 0. 16/ 0


___ 77J____________________ 220X 250X 550_____________________ 92J____

| |
| |
| |
| |
| 4No16 H 54. 0.TO 220 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | 4#16 | | |
| oooo | | oooo | | oooo | | oooo | | oooo | | oooo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 2 - 16MM 0. 430. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 150./ 0. 27./ 0. 17/ 0

36. 160./ 0. 29./ 0. 17/ 0
72. 170./ 0. 30./ 0. 17/ 0
108. 180./ 0. 32./ 0. 17/ 0
143. 191./ 0. 34./ 0. 20/ 0
179. 204./ 0. 37./ 0. 20/ 0
215. 218./ 0. 39./ 0. 20/ 0
251. 231./ 0. 41./ 0. 20/ 0
287. 244./ 0. 43./ 0. 20/ 0
323. 257./ 0. 46./ 0. 20/ 0
358. 270./ 0. 48./ 0. 20/ 0
394. 283./ 0. 50./ 0. 20/ 0
430. 296./ 0. 52./ 0. 20/ 0



___ 75J____________________ 430X 250X 550_____________________ 106J____

| |
| |
| |
| |
| 2No16 H 54. 0.TO 430 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 3 - 12MM 0. 2570. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 148. 3 - 12MM 0. 2570. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 46./ 217. 2./ 11. 22/ 16

214. 71./ 165. 4./ 8. 22/ 16
428. 91./ 123. 5./ 6. 22/ 16
642. 112./ 95. 6./ 5. 17/ 21
857. 130./ 81. 7./ 4. 17/ 21
1071. 140./ 71. 7./ 4. 17/ 21
1285. 140./ 67. 7./ 3. 17/ 21
1499. 131./ 68. 7./ 3. 17/ 21
1713. 113./ 74. 6./ 4. 17/ 21
1928. 88./ 86. 4./ 4. 22/ 16
2142. 67./ 118. 3./ 6. 22/ 16
2356. 40./ 158. 2./ 8. 22/ 16
2570. 10./ 209. 0./ 10. 21/ 17

___ 104J____________________ 2570X 400X 200_____________________ 105J____

| |
| |
||=========================================================================||
| 3No12cHc152.| 0.TO 2570| | | | | | | | | | | | 17*8 c/c 74 | |
||=========================================================================||
| |
| |
|___________________________________________________________________________|
_______________________ _______________________ _______________________
| | | | | |
| | | | | |
| ooo | | ooo | | ooo |
| 3#12 | | 3#12 | | 3#12 |
| ooo | | ooo | | ooo |
| | | | | |
| | | | | |
|_______________________| |_______________________| |_______________________|

=============================================

_____________________________________________________________________
1 52. 3 - 12MM 23. 2785. NO NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 148. 3 - 12MM 0. 2930. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 0./ 204. 0./ 10. 0/ 16

244. 11./ 159. 1./ 8. 22/ 16
488. 29./ 122. 1./ 6. 22/ 16
732. 43./ 92. 2./ 5. 22/ 16
977. 54./ 70. 3./ 4. 22/ 16
1221. 62./ 56. 3./ 3. 17/ 21
1465. 68./ 52. 3./ 3. 17/ 21
1709. 67./ 51. 3./ 3. 17/ 21
1953. 60./ 54. 3./ 3. 17/ 21
2197. 47./ 64. 2./ 3. 22/ 16
2442. 34./ 83. 2./ 4. 22/ 16
2686. 17./ 110. 1./ 6. 22/ 16
2930. 0./ 145. 0./ 7. 0/ 17

___ 105J____________________ 2929X 400X 200_____________________ 106J____

| |
| |
||=========================================================================||
| 3No12cHc152.| 23.TO 2785| | | | | | | | | | | | | | | | | |19*8 c/c 74| |
|======================================================================== |
| |
| |
|___________________________________________________________________________|
_______________________ _______________________ _______________________
| | | | | |
| | | | | |
| ooo | | ooo | | ooo |
| 3#12 | | 3#12 | | 3#12 |
| | | ooo | | |
| | | | | |
| | | | | |
|_______________________| |_______________________| |_______________________|

=============================================

_____________________________________________________________________
1 54. 4 - 16MM 0. 1280. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 690./ 0. 117./ 0. 17/ 0

107. 706./ 0. 120./ 0. 17/ 0
213. 720./ 0. 122./ 0. 17/ 0
320. 731./ 0. 124./ 0. 17/ 0
427. 739./ 0. 125./ 0. 17/ 0
533. 744./ 0. 126./ 0. 17/ 0
640. 746./ 0. 126./ 0. 17/ 0
747. 749./ 0. 127./ 0. 20/ 0

853. 748./ 0. 127./ 0. 20/ 0

960. 744./ 0. 126./ 0. 20/ 0
1067. 736./ 0. 125./ 0. 20/ 0
1173. 725./ 0. 123./ 0. 20/ 0
1280. 710./ 0. 121./ 0. 20/ 0
___ 92J____________________ 1280X 250X 550_____________________ 121J____

| |
| |
| |
| 2*8 c/c248 |
| 4No16 H 54. 0.TO 1280 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| 4#16 | | 4#16 | | 4#16 |
| oooo | | oooo | | oooo |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 3 - 16MM 0. 1070. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 288./ 0. 51./ 0. 20/ 0

89. 315./ 0. 56./ 0. 20/ 0
178. 340./ 0. 60./ 0. 20/ 0
268. 365./ 0. 64./ 0. 20/ 0
357. 388./ 0. 68./ 0. 20/ 0
446. 410./ 0. 72./ 0. 20/ 0
535. 430./ 0. 75./ 0. 20/ 0
624. 449./ 0. 78./ 0. 20/ 0
713. 466./ 0. 81./ 0. 20/ 0
802. 482./ 0. 84./ 0. 20/ 0
892. 497./ 0. 86./ 0. 20/ 0
981. 510./ 0. 88./ 0. 20/ 0
1070. 521./ 0. 90./ 0. 20/ 0

___ 106J____________________ 1070X 250X 550_____________________ 119J____

| |
| |
| |
| 2*8 c/c248 2*8 c/c248 |
| 3No16 H 54. 0.TO 1070 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| 3#16 | | 3#16 | | 3#16 |
| ooo | | ooo | | ooo |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 59. 2 - 25MM 0. 6180. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 491. 3 - 25MM 0. 6180. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 247./ 1020. 44./ 171. 22/ 16

515. 399./ 762. 70./ 130. 22/ 16
1030. 528./ 564. 92./ 98. 22/ 16
1545. 696./ 480. 120./ 84. 17/ 21
2060. 831./ 435. 141./ 77. 17/ 21
2575. 919./ 417. 155./ 73. 17/ 21
3090. 956./ 424. 161./ 75. 17/ 21
3605. 941./ 457. 159./ 80. 17/ 21
4120. 875./ 516. 148./ 90. 17/ 21
4635. 759./ 603. 130./ 105. 17/ 21
5150. 629./ 750. 109./ 129. 22/ 16
5665. 522./ 1005. 91./ 168. 22/ 16
6180. 392./ 1327. 69./ 216. 21/ 17

___ 93J____________________ 6180X 300X 550_____________________ 188J____

| |
||=========================================================================||
| 3No25 H 491.| 0.TO 6180| | | | | | | | | | | | | | | | | |
| 17*8 c/c170 | | | | | | | | | | | | | | | | 17*8 c/c170 | |
| 2No25 H 59.| 0.TO 6180| | | | | | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| ooo | | ooo | | ooo |
| 3#25 | | 3#25 | | 3#25 |
| | | | | |
| 2#25 | | 2#25 | | 2#25 |
| oo | | oo | | oo |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 4 - 16MM 0. 2700. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
*** A SUITABLE BAR ARRANGEMENT COULD NOT BE DETERMINED.

REQD. STEEL = 1655. MM2, MAX. STEEL PERMISSIBLE = 1954. MM2
MAX NEG MOMENT = 253.52 KN-MET, LOADING 17

-------------------------------
0. 722./ 0. 122./ 0. 20/ 0

225. 689./ 0. 117./ 0. 17/ 0
450. 660./ 0. 113./ 0. 17/ 0

675. 615./ 0. 105./ 0. 17/ 0

900. 554./ 56. 96./ 10. 17/ 21
1125. 479./ 148. 83./ 27. 17/ 21
1350. 391./ 250. 69./ 45. 17/ 21
1575. 304./ 378. 54./ 66. 22/ 16
1800. 256./ 573. 46./ 99. 22/ 16
2025. 202./ 794. 36./ 134. 22/ 16
2250. 140./ 1043. 25./ 171. 22/ 16
2475. 72./ 1328. 13./ 211. 22/ 16
2700. 0./ 1655. 0./ 254. 0/ 17
___ 121J____________________ 2700X 250X 550_____________________ 243J____

| |
| |
| |
| |
| 4No16 H 54. 0.TO 2700 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| 4#16 | | 4#16 | | 4#16 |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 54. 3 - 16MM 0. 2804. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 494. 3 - 20MM 304. 2820. NO YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 527./ 0. 91./ 0. 20/ 0

235. 521./ 0. 90./ 0. 20/ 0
470. 496./ 0. 86./ 0. 17/ 0
705. 471./ 0. 82./ 0. 17/ 0
940. 429./ 0. 75./ 0. 17/ 0
1175. 371./ 0. 65./ 0. 17/ 0
1410. 298./ 37. 53./ 7. 17/ 21
1645. 210./ 104. 37./ 19. 17/ 21
1880. 125./ 198. 23./ 35. 22/ 16
2115. 68./ 347. 12./ 61. 22/ 16
2350. 3./ 517. 1./ 90. 22/ 16
2585. 0./ 711. 0./ 121. 0/ 16
2820. 0./ 933. 0./ 155. 0/ 17

___ 119J____________________ 2820X 250X 550_____________________ 248J____

| |
| ===================================================================||
| 3No20 H 494. 304.TO 2820 | | | | | | | |
| 7*8 c/c158 | | | | | | | | 7*10c/c158 | |
| 3No16 H 54. 0.TO 2804 | | | | | | | | | |
||==========================================================================|
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| | | ooo | | ooo |
| | | 3#20 | | 3#20 |
| | | | | |
| 3#16 | | 3#16 | | |
| ooo | | ooo | | |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 4 - 12MM 0. 5500. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 4 - 12MM 0. 5500. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 276./ 327. 49./ 58. 22/ 16

458. 294./ 304. 52./ 54. 17/ 21
917. 311./ 288. 55./ 51. 17/ 21
1375. 324./ 275. 57./ 49. 17/ 21
1833. 331./ 266. 58./ 47. 17/ 21
2292. 333./ 260. 59./ 46. 17/ 21
2750. 330./ 258. 58./ 46. 17/ 21
3208. 322./ 260. 57./ 46. 17/ 21
3667. 310./ 265. 55./ 47. 17/ 21
4125. 292./ 273. 52./ 48. 17/ 21
4583. 274./ 289. 49./ 51. 22/ 16
5042. 254./ 313. 45./ 55. 22/ 16
5500. 231./ 341. 41./ 60. 21/ 17
___ 194J____________________ 5500X 250X 550_____________________ 195J____

| |
||=========================================================================||
| 4No12 H 498. 0.TO 5500 |
| |
| 4No12 H 52. 0.TO 5500 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| 4#12 | | 4#12 | | 4#12 |
| | | | | |
| 4#12 | | 4#12 | | 4#12 |
| | | | | |
|_______| |_______| |_______|


=============================================

_____________________________________________________________________
1 52. 4 - 12MM 0. 5600. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 498. 4 - 12MM 0. 5600. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 247./ 281. 44./ 50. 17/ 21

467. 270./ 269. 48./ 48. 17/ 21
933. 288./ 260. 51./ 46. 17/ 21
1400. 301./ 254. 53./ 45. 17/ 21
1867. 309./ 253. 55./ 45. 17/ 21
2333. 312./ 255. 55./ 45. 17/ 21
2800. 309./ 260. 55./ 46. 17/ 21
3267. 301./ 270. 53./ 48. 17/ 21
3733. 292./ 286. 52./ 51. 22/ 16
4200. 282./ 310. 50./ 55. 22/ 16
4667. 268./ 340. 48./ 60. 22/ 16
5133. 250./ 375. 44./ 66. 22/ 16
5600. 229./ 415. 41./ 73. 21/ 17

___ 195J____________________ 5600X 250X 550_____________________ 196J____

| |
||=========================================================================||
| 4No12 H 498. 0.TO 5600 |
| |
| 4No12 H 52. 0.TO 5600 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| 4#12 | | 4#12 | | 4#12 |
| | | | | |
| 4#12 | | 4#12 | | 4#12 |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 3 - 12MM 0. 5400. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 496. 2 - 16MM 0. 5400. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 199./ 227. 36./ 40. 17/ 21

450. 217./ 209. 39./ 37. 17/ 21
900. 231./ 195. 41./ 35. 17/ 21
1350. 240./ 184. 43./ 33. 17/ 21
1800. 244./ 176. 43./ 32. 17/ 21
2250. 244./ 172. 43./ 31. 17/ 21
2700. 239./ 172. 43./ 31. 17/ 21
3150. 229./ 174. 41./ 31. 17/ 21
3600. 214./ 180. 38./ 32. 17/ 21
4050. 199./ 193. 36./ 34. 22/ 16
4500. 183./ 213. 33./ 38. 22/ 16
4950. 164./ 239. 29./ 42. 22/ 16
5400. 141./ 269. 25./ 48. 21/ 17

___ 196J____________________ 5400X 250X 550_____________________ 197J____

| |
||=========================================================================||
| 2No16 H 496. 0.TO 5400 |
| |
| 3No12 H 52. 0.TO 5400 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 |
| | | | | |
| 3#12 | | 3#12 | | 3#12 |
| ooo | | ooo | | ooo |
| | | | | |
|_______| |_______| |_______|

=============================================

_____________________________________________________________________
1 52. 2 - 12MM 0. 358. YES NO

|----------------------------------------------------------------|
|----------------------------------------------------------------|
2 494. 3 - 20MM 0. 400. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|


-------------------------------
0. 98./ 860. 18./ 144. 22/ 16

33. 76./ 827. 14./ 139. 22/ 16
67. 53./ 794. 10./ 134. 22/ 16
100. 30./ 762. 5./ 129. 22/ 16
133. 7./ 731. 1./ 124. 22/ 16
167. 0./ 700. 0./ 119. 0/ 16
200. 0./ 669. 0./ 114. 0/ 16
233. 0./ 639. 0./ 109. 0/ 16
267. 0./ 610. 0./ 105. 0/ 16
300. 0./ 581. 0./ 100. 0/ 16
333. 0./ 553. 0./ 95. 0/ 16
367. 0./ 525. 0./ 91. 0/ 16
400. 0./ 520. 0./ 90. 0/ 20


___ 243J____________________ 399X 250X 550_____________________ 231J____

| |
||=========================================================================||
| 3No20 H 494. 0.TO 400 |
| |
| 2No12 H 52. 0.TO 358 |
||=================================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| ooo | | ooo | | ooo |
| 3#20 | | 3#20 | | 3#20 |
| | | | | |
| 2#12 | | 2#12 | | |
| oo | | oo | | |
| | | | | |
|_______| |_______| |_______|


=============================================

_____________________________________________________________________
1 496. 3 - 16MM 0. 280. YES YES

|----------------------------------------------------------------|
|----------------------------------------------------------------|

-------------------------------
0. 0./ 532. 0./ 92. 0/ 16

23. 0./ 527. 0./ 91. 0/ 16
47. 0./ 522. 0./ 90. 0/ 16
70. 0./ 517. 0./ 90. 0/ 16
93. 0./ 512. 0./ 89. 0/ 16
117. 0./ 507. 0./ 88. 0/ 16
140. 0./ 503. 0./ 87. 0/ 16
163. 0./ 498. 0./ 86. 0/ 16
187. 0./ 495. 0./ 86. 0/ 20
210. 0./ 501. 0./ 87. 0/ 20
233. 0./ 508. 0./ 88. 0/ 20
257. 0./ 515. 0./ 89. 0/ 20
280. 0./ 523. 0./ 90. 0/ 20



___ 248J____________________ 280X 250X 550_____________________ 223J____

| |
||=========================================================================||
| 3No16 H 496. 0.TO 280 |
| |
| |
| |
| |
|___________________________________________________________________________|
_______ _______ _______
| | | | | |
| ooo | | ooo | | ooo |
| 3#16 | | 3#16 | | 3#16 |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
|_______| |_______| |_______|
********************END OF BEAM DESIGN**************************
526. *81 118 TO 120 147 251 263 294 303 366 469
527. *DESIGN COLUMN
528. *DESIGN ELEMENT
529. END CONCRETE DESIGN
530. FINISH
*********** END OF THE STAAD.Pro RUN ***********
**** DATE= AUG 15,2022 TIME= 7:12:39 ****

7.1.6 Diseño de Columnas y Placas. Usando el Programa Staad Pró
Elevación
_________________________________________________________________________________________

ACI 318-11 COLUMN NO. 4 DESIGN RESULTS

===============================================
FY - 413.7 FC - 20.6 MPA, RECT SIZE -1000.0 X 250.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 2500.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------
8 - 20 MM 1.005 1 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 8 SPACING 250.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
5371.93 4297.55 1691.94 186.64 110.3
M0 P-tens. Des.Pn Des.Mn e/h
99.45 -1039.71 151.47 0.67 0.00168
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
5371.93 4297.55 2110.51 890.98 422.2
471.91 -1039.71 151.47 4.28 0.01074
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3966.97 120.75 1983.48 184.95
P0 |* 3636.39 140.47 1652.90 185.65
| * 3305.80 155.60 1322.32 175.51
Pn,max|__* 2975.22 167.59 991.74 162.75
| * 2644.64 176.57 661.16 148.23
Pn | * 2314.06 181.86 330.58 125.57
NOMINAL| * Pn Mn Pn Mn (@ Y )
AXIAL| * 3966.97 541.82 1983.48 887.33
COMPRESSION| * 3636.39 631.93 1652.90 865.17
Pb|-------*Mb 3305.80 707.47 1322.32 829.12
| * 2975.22 770.34 991.74 782.75
___________|____*_______ 2644.64 822.67 661.16 713.28
| * M0 Mn, 2314.06 866.80 330.58 606.33
| * BENDING
P-tens|* MOMENT
|
C:\Users\Secretearia\Desktop\Modelo Trinidad Moran\Edificio Trinidad 1.anl Page 22 of 65


===============================================


----------------------------------------------------------
8 - 20 MM 1.005 1 END 0.650

--------------------------------------------------------
5371.93 4297.55 1691.94 186.64 110.3
99.45 -1039.71 170.60 2.71 0.00603
--------------------------------------------------------
--------------------------------------------------------
5371.93 4297.55 2110.51 890.98 422.2
471.91 -1039.71 170.60 3.41 0.00760
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3966.97 120.75 1983.48 184.95
P0 |* 3636.39 140.47 1652.90 185.65
| * 3305.80 155.60 1322.32 175.51
Pn,max|__* 2975.22 167.59 991.74 162.75
| * 2644.64 176.57 661.16 148.23
Pn | * 2314.06 181.86 330.58 125.57
AXIAL| * 3966.97 541.82 1983.48 887.33
COMPRESSION| * 3636.39 631.93 1652.90 865.17
Pb|-------*Mb 3305.80 707.47 1322.32 829.12
| * 2975.22 770.34 991.74 782.75
___________|____*_______ 2644.64 822.67 661.16 713.28
| * M0 Mn, 2314.06 866.80 330.58 606.33
| * BENDING
P-tens|* MOMENT
|


===============================================
FY - 413.7 FC - 20.6 MPA, RECT SIZE - 500.0 X 250.0 MMS, TIED


----------------------------------------------------------
4 - 20 MM 1.005 1 END 0.650

--------------------------------------------------------
2685.97 2148.77 843.22 102.43 121.5
49.44 -519.85 65.87 1.14 0.00656
--------------------------------------------------------
--------------------------------------------------------
2685.97 2148.77 983.86 238.37 242.3
110.02 -519.85 65.87 0.92 0.00533
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1983.48 63.90 991.74 100.82
P0 |* 1818.19 74.52 826.45 101.90
| * 1652.90 82.86 661.16 95.21
Pn,max|__* 1487.61 89.70 495.87 86.18
| * 1322.32 95.12 330.58 75.20
Pn | * 1157.03 98.50 165.29 62.78
AXIAL| * 1983.48 140.11 991.74 237.86
COMPRESSION| * 1818.19 163.16 826.45 231.97
Pb|-------*Mb 1652.90 183.12 661.16 219.16
| * 1487.61 199.98 495.87 199.22
___________|____*_______ 1322.32 214.29 330.58 172.87
| * M0 Mn, 1157.03 226.70 165.29 142.65
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 122.76 1.63 0.00493
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 122.76 4.96 0.01497
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 135.38 4.80 0.01312
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 135.38 4.07 0.01114
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 78.76 0.61 0.00288
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 78.76 2.18 0.01023
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 98.29 2.63 0.00992
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 98.29 5.51 0.02077
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 106.41 5.25 0.01826
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 106.41 4.08 0.01418
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 58.27 0.46 0.00295
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 58.27 2.77 0.01761
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 71.23 3.26 0.01695
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 71.23 5.55 0.02888
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 82.09 5.39 0.02432
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 82.09 4.39 0.01979
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 42.01 0.30 0.00266
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 42.01 2.91 0.02569
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 42.60 2.62 0.02274
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 42.60 5.91 0.05142
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 62.23 2.96 0.01762
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 62.23 5.60 0.03334
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 24.26 0.18 0.00277
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 24.26 3.22 0.04920
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 1 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 8.82 8.33 0.35009
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 8.82 11.78 0.49488
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 32 MM 1.608 19 END 0.650

--------------------------------------------------------
4775.48 3820.38 951.58 127.12 133.6
85.53 -1330.82 171.53 79.08 0.17075
--------------------------------------------------------
--------------------------------------------------------
4775.48 3820.38 1637.77 1017.46 621.2
597.33 -1330.82 171.53 41.27 0.08910
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3526.51 82.14 1763.25 122.98
P0 |* 3232.63 95.40 1469.38 124.87
| * 2938.76 104.82 1175.50 126.25
Pn,max|__* 2644.88 111.33 881.63 124.75
| * 2351.00 116.55 587.75 113.35
Pn | * 2057.13 120.31 293.88 100.11
AXIAL| * 3526.51 536.87 1763.25 991.28
COMPRESSION| * 3232.63 631.30 1469.38 1009.34
Pb|-------*Mb 2938.76 717.29 1175.50 975.77
| * 2644.88 794.18 881.63 917.54
___________|____*_______ 2351.00 864.07 587.75 834.63
| * M0 Mn, 2057.13 929.08 293.88 722.90
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 6.65 0.27 0.01509
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 6.65 5.24 0.29159
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 20 MM 1.257 1 END 0.650

--------------------------------------------------------
2248.34 1798.68 573.13 63.34 110.5
36.44 -519.85 23.03 2.29 0.03679
--------------------------------------------------------
--------------------------------------------------------
2248.34 1798.68 784.89 211.24 269.1
108.97 -519.85 23.03 2.39 0.03838
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 1660.32 40.59 830.16 61.84
P0 |* 1521.96 47.45 691.80 62.75
| * 1383.60 52.90 553.44 62.73
Pn,max|__* 1245.24 56.13 415.08 57.65
| * 1106.88 58.70 276.72 51.37
Pn | * 968.52 60.55 138.36 44.21
AXIAL| * 1660.32 118.34 830.16 207.74
COMPRESSION| * 1521.96 138.46 691.80 207.90
Pb|-------*Mb 1383.60 156.16 553.44 198.35
| * 1245.24 171.44 415.08 182.77
___________|____*_______ 1106.88 184.78 276.72 161.02
| * M0 Mn, 968.52 196.70 138.36 136.01
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
16 - 12 MM 1.005 1 END 0.650

--------------------------------------------------------
3867.78 3094.23 1338.16 169.10 126.4
89.49 -748.58 87.41 0.47 0.00205
--------------------------------------------------------
--------------------------------------------------------
3867.78 3094.23 1486.64 365.42 245.8
194.92 -748.58 87.41 1.60 0.00698
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 2856.21 107.15 1428.10 167.61
P0 |* 2618.19 124.02 1190.09 166.28
| * 2380.17 137.79 952.07 159.17
Pn,max|__* 2142.16 148.58 714.05 146.87
| * 1904.14 156.74 476.03 131.69
Pn | * 1666.12 162.93 238.02 111.81
AXIAL| * 2856.21 227.70 1428.10 364.71
COMPRESSION| * 2618.19 264.43 1190.09 358.15
Pb|-------*Mb 2380.17 294.72 952.07 344.27
| * 2142.16 319.22 714.05 320.59
___________|____*_______ 1904.14 339.03 476.03 288.62
| * M0 Mn, 1666.12 355.12 238.02 245.78
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
12 - 16 MM 1.340 22 STA 0.650

--------------------------------------------------------
4106.77 3285.42 1321.25 186.83 141.4
114.63 -998.13 381.60 128.26 0.12449
--------------------------------------------------------
--------------------------------------------------------
4106.77 3285.42 1483.12 410.44 276.7
255.69 -998.13 381.60 25.44 0.02469
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3032.69 111.64 1516.35 182.32
P0 |* 2779.97 130.55 1263.62 185.69
| * 2527.24 145.36 1010.90 178.58
Pn,max|__* 2274.52 157.74 758.17 169.58
| * 2021.79 167.69 505.45 154.07
Pn | * 1769.07 175.69 252.72 135.82
AXIAL| * 3032.69 241.95 1516.35 408.15
COMPRESSION| * 2779.97 281.64 1263.62 405.71
Pb|-------*Mb 2527.24 315.98 1010.90 395.43
| * 2274.52 344.79 758.17 377.32
___________|____*_______ 2021.79 369.07 505.45 345.67
| * M0 Mn, 1769.07 389.82 252.72 307.94
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 2.793 17 STA 0.650

--------------------------------------------------------
5142.29 4113.83 1090.17 287.77 264.0
208.46 -2079.40 722.54 214.66 0.11003
--------------------------------------------------------
--------------------------------------------------------
5142.29 4113.83 1387.60 726.71 523.7
509.92 -2079.40 722.54 42.67 0.02187
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3797.38 141.19 1898.69 261.35
P0 |* 3480.93 169.27 1582.24 271.93
| * 3164.48 193.67 1265.79 282.16
Pn,max|__* 2848.04 213.87 949.35 280.33
| * 2531.59 232.83 632.90 259.94
Pn | * 2215.14 250.12 316.45 235.56
AXIAL| * 3797.38 304.57 1898.69 653.02
COMPRESSION| * 3480.93 398.53 1582.24 698.59
Pb|-------*Mb 3164.48 455.58 1265.79 721.96
| * 2848.04 509.43 949.35 696.42
___________|____*_______ 2531.59 559.47 632.90 647.09
| * M0 Mn, 2215.14 606.96 316.45 581.54
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 2.793 17 STA 0.650

--------------------------------------------------------
5142.29 4113.83 1090.17 287.77 264.0
208.46 -2079.40 568.48 222.47 0.14494
--------------------------------------------------------
--------------------------------------------------------
5142.29 4113.83 1387.60 726.71 523.7
509.92 -2079.40 568.48 35.48 0.02311
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3797.38 141.19 1898.69 261.35
P0 |* 3480.93 169.27 1582.24 271.93
| * 3164.48 193.67 1265.79 282.16
Pn,max|__* 2848.04 213.87 949.35 280.33
| * 2531.59 232.83 632.90 259.94
Pn | * 2215.14 250.12 316.45 235.56
AXIAL| * 3797.38 304.57 1898.69 653.02
COMPRESSION| * 3480.93 398.53 1582.24 698.59
Pb|-------*Mb 3164.48 455.58 1265.79 721.96
| * 2848.04 509.43 949.35 696.42
___________|____*_______ 2531.59 559.47 632.90 647.09
| * M0 Mn, 2215.14 606.96 316.45 581.54
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 2.793 17 STA 0.650

--------------------------------------------------------
5142.29 4113.83 1090.17 287.77 264.0
208.46 -2079.40 420.45 214.53 0.18898
--------------------------------------------------------
--------------------------------------------------------
5142.29 4113.83 1387.60 726.71 523.7
509.92 -2079.40 420.45 33.04 0.02910
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 3797.38 141.19 1898.69 261.35
P0 |* 3480.93 169.27 1582.24 271.93
| * 3164.48 193.67 1265.79 282.16
Pn,max|__* 2848.04 213.87 949.35 280.33
| * 2531.59 232.83 632.90 259.94
Pn | * 2215.14 250.12 316.45 235.56
AXIAL| * 3797.38 304.57 1898.69 653.02
COMPRESSION| * 3480.93 398.53 1582.24 698.59
Pb|-------*Mb 3164.48 455.58 1265.79 721.96
| * 2848.04 509.43 949.35 696.42
___________|____*_______ 2531.59 559.47 632.90 647.09
| * M0 Mn, 2215.14 606.96 316.45 581.54
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 50 MM 4.363 17 END 0.650

--------------------------------------------------------
6262.46 5009.97 853.86 360.94 422.7
301.26 -3249.06 288.01 242.30 0.31159
--------------------------------------------------------
--------------------------------------------------------
6262.46 5009.97 1349.65 987.39 731.6
775.68 -3249.06 288.01 113.90 0.14648
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 4624.58 161.88 2312.29 310.19
P0 |* 4239.20 196.62 1926.91 323.99
| * 3853.82 227.23 1541.53 337.40
Pn,max|__* 3468.44 253.34 1156.15 350.61
| * 3083.06 278.17 770.76 356.11
Pn | * 2697.67 295.72 385.38 330.61
AXIAL| * 4624.58 372.25 2312.29 828.49
COMPRESSION| * 4239.20 484.42 1926.91 891.88
Pb|-------*Mb 3853.82 559.84 1541.53 955.48
| * 3468.44 631.55 1156.15 978.03
___________|____*_______ 3083.06 699.35 770.76 935.07
| * M0 Mn, 2697.67 764.61 385.38 859.36
| * BENDING
P-tens|* MOMENT
|


===============================================
FY - 413.7 FC - 20.6 MPA, RECT SIZE - 300.0 X1800.0 MMS, TIED


----------------------------------------------------------
12 - 25 MM 1.091 1 END 0.650

--------------------------------------------------------
11786.31 9429.05 4724.00 3562.80 754.2
2044.40 -2436.79 765.09 10.60 0.00527
--------------------------------------------------------
--------------------------------------------------------
11786.31 9429.05 3844.29 507.44 132.0
282.48 -2436.79 765.09 3.07 0.00152
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 8703.74 2173.04 4351.87 3554.53
P0 |* 7978.42 2531.48 3626.56 3495.69
| * 7253.11 2833.72 2901.25 3391.62
Pn,max|__* 6527.80 3087.35 2175.93 3171.57
| * 5802.49 3300.84 1450.62 2872.56
Pn | * 5077.18 3482.51 725.31 2530.16
AXIAL| * 8703.74 319.76 4351.87 502.17
COMPRESSION| * 7978.42 372.18 3626.56 502.04
Pb|-------*Mb 7253.11 412.69 2901.25 479.40
| * 6527.80 445.38 2175.93 450.01
___________|____*_______ 5802.49 470.45 1450.62 402.28
| * M0 Mn, 5077.18 489.22 725.31 348.77
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
12 - 25 MM 1.091 1 END 0.650

--------------------------------------------------------
11786.31 9429.05 4724.00 3562.80 754.2
2044.40 -2436.79 662.49 20.67 0.01156
--------------------------------------------------------
--------------------------------------------------------
11786.31 9429.05 3844.29 507.44 132.0
282.48 -2436.79 662.49 1.58 0.00088
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 8703.74 2173.04 4351.87 3554.53
P0 |* 7978.42 2531.48 3626.56 3495.69
| * 7253.11 2833.72 2901.25 3391.62
Pn,max|__* 6527.80 3087.35 2175.93 3171.57
| * 5802.49 3300.84 1450.62 2872.56
Pn | * 5077.18 3482.51 725.31 2530.16
AXIAL| * 8703.74 319.76 4351.87 502.17
COMPRESSION| * 7978.42 372.18 3626.56 502.04
Pb|-------*Mb 7253.11 412.69 2901.25 479.40
| * 6527.80 445.38 2175.93 450.01
___________|____*_______ 5802.49 470.45 1450.62 402.28
| * M0 Mn, 5077.18 489.22 725.31 348.77
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 50 MM 1.190 1 END 0.650

--------------------------------------------------------
14664.80 11731.84 5576.54 6473.17 1160.8
3374.93 -3249.06 528.41 5.69 0.00399
--------------------------------------------------------
--------------------------------------------------------
14664.80 11731.84 4191.69 662.72 158.1
354.94 -3249.06 528.41 0.63 0.00044
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 10829.39 3645.55 5414.69 6466.63
P0 |* 9926.94 4279.42 4512.25 6338.70
| * 9024.49 4834.77 3609.80 6055.70
Pn,max|__* 8122.04 5324.20 2707.35 5617.61
| * 7219.59 5761.62 1804.90 5024.44
Pn | * 6317.14 6161.84 902.45 4276.18
AXIAL| * 10829.39 409.81 5414.69 646.60
COMPRESSION| * 9926.94 479.34 4512.25 658.89
Pb|-------*Mb 9024.49 534.14 3609.80 635.33
| * 8122.04 579.30 2707.35 580.67
___________|____*_______ 7219.59 609.94 1804.90 513.57
| * M0 Mn, 6317.14 630.85 902.45 437.30
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 50 MM 1.190 1 END 0.650

--------------------------------------------------------
14664.80 11731.84 5576.54 6473.17 1160.8
3374.93 -3249.06 394.45 14.66 0.01376
--------------------------------------------------------
--------------------------------------------------------
14664.80 11731.84 4191.69 662.72 158.1
354.94 -3249.06 394.45 1.45 0.00136
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 10829.39 3645.55 5414.69 6466.63
P0 |* 9926.94 4279.42 4512.25 6338.70
| * 9024.49 4834.77 3609.80 6055.70
Pn,max|__* 8122.04 5324.20 2707.35 5617.61
| * 7219.59 5761.62 1804.90 5024.44
Pn | * 6317.14 6161.84 902.45 4276.18
AXIAL| * 10829.39 409.81 5414.69 646.60
COMPRESSION| * 9926.94 479.34 4512.25 658.89
Pb|-------*Mb 9024.49 534.14 3609.80 635.33
| * 8122.04 579.30 2707.35 580.67
___________|____*_______ 7219.59 609.94 1804.90 513.57
| * M0 Mn, 6317.14 630.85 902.45 437.30
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 50 MM 1.190 1 END 0.650

--------------------------------------------------------
14664.80 11731.84 5576.54 6473.17 1160.8
3374.93 -3249.06 260.16 25.20 0.03588
--------------------------------------------------------
--------------------------------------------------------
14664.80 11731.84 4191.69 662.72 158.1
354.94 -3249.06 260.16 2.59 0.00368
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 10829.39 3645.55 5414.69 6466.63
P0 |* 9926.94 4279.42 4512.25 6338.70
| * 9024.49 4834.77 3609.80 6055.70
Pn,max|__* 8122.04 5324.20 2707.35 5617.61
| * 7219.59 5761.62 1804.90 5024.44
Pn | * 6317.14 6161.84 902.45 4276.18
AXIAL| * 10829.39 409.81 5414.69 646.60
COMPRESSION| * 9926.94 479.34 4512.25 658.89
Pb|-------*Mb 9024.49 534.14 3609.80 635.33
| * 8122.04 579.30 2707.35 580.67
___________|____*_______ 7219.59 609.94 1804.90 513.57
| * M0 Mn, 6317.14 630.85 902.45 437.30
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 50 MM 1.190 1 END 0.650

--------------------------------------------------------
14664.80 11731.84 5576.54 6473.17 1160.8
3374.93 -3249.06 126.93 106.65 0.31120
--------------------------------------------------------
--------------------------------------------------------
14664.80 11731.84 4191.69 662.72 158.1
354.94 -3249.06 126.93 14.56 0.04249
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 10829.39 3645.55 5414.69 6466.63
P0 |* 9926.94 4279.42 4512.25 6338.70
| * 9024.49 4834.77 3609.80 6055.70
Pn,max|__* 8122.04 5324.20 2707.35 5617.61
| * 7219.59 5761.62 1804.90 5024.44
Pn | * 6317.14 6161.84 902.45 4276.18
AXIAL| * 10829.39 409.81 5414.69 646.60
COMPRESSION| * 9926.94 479.34 4512.25 658.89
Pb|-------*Mb 9024.49 534.14 3609.80 635.33
| * 8122.04 579.30 2707.35 580.67
___________|____*_______ 7219.59 609.94 1804.90 513.57
| * M0 Mn, 6317.14 630.85 902.45 437.30
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.047 1 END 0.650

--------------------------------------------------------
10393.75 8315.00 4029.41 3188.98 791.4
1549.62 -2079.40 689.49 16.20 0.00893
--------------------------------------------------------
--------------------------------------------------------
10393.75 8315.00 3220.35 477.69 148.3
235.54 -2079.40 689.49 0.16 0.00009
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7675.38 1844.21 3837.69 3180.82
P0 |* 7035.77 2159.16 3198.08 3102.95
| * 6396.15 2432.10 2558.46 2947.18
Pn,max|__* 5756.54 2669.33 1918.85 2713.51
| * 5116.92 2877.93 1279.23 2401.94
Pn | * 4477.31 3065.64 639.62 2007.89
AXIAL| * 7675.38 296.13 3837.69 469.26
COMPRESSION| * 7035.77 345.66 3198.08 476.84
Pb|-------*Mb 6396.15 384.61 2558.46 446.23
| * 5756.54 416.69 1918.85 404.77
___________|____*_______ 5116.92 442.24 1279.23 354.25
| * M0 Mn, 4477.31 458.08 639.62 297.06
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.047 1 END 0.650

--------------------------------------------------------
10393.75 8315.00 4029.41 3188.98 791.4
1549.62 -2079.40 648.12 4.81 0.00275
--------------------------------------------------------
--------------------------------------------------------
10393.75 8315.00 3220.35 477.69 148.3
235.54 -2079.40 648.12 1.51 0.00086
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7675.38 1844.21 3837.69 3180.82
P0 |* 7035.77 2159.16 3198.08 3102.95
| * 6396.15 2432.10 2558.46 2947.18
Pn,max|__* 5756.54 2669.33 1918.85 2713.51
| * 5116.92 2877.93 1279.23 2401.94
Pn | * 4477.31 3065.64 639.62 2007.89
AXIAL| * 7675.38 296.13 3837.69 469.26
COMPRESSION| * 7035.77 345.66 3198.08 476.84
Pb|-------*Mb 6396.15 384.61 2558.46 446.23
| * 5756.54 416.69 1918.85 404.77
___________|____*_______ 5116.92 442.24 1279.23 354.25
| * M0 Mn, 4477.31 458.08 639.62 297.06
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
8 - 32 MM 1.072 1 END 0.650

--------------------------------------------------------
13051.93 10441.54 5197.36 4472.84 860.6
2506.02 -2661.63 526.62 6.39 0.00450
--------------------------------------------------------
--------------------------------------------------------
13051.93 10441.54 4170.10 560.62 134.4
305.71 -2661.63 526.62 2.49 0.00175
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 9638.35 2689.30 4819.17 4456.16
P0 |* 8835.15 3140.98 4015.98 4355.32
| * 8031.96 3523.84 3212.78 4187.02
Pn,max|__* 7228.76 3847.24 2409.59 3968.79
| * 6425.57 4121.69 1606.39 3652.48
Pn | * 5622.37 4358.61 803.20 3141.78
AXIAL| * 9638.35 353.92 4819.17 554.06
COMPRESSION| * 8835.15 412.44 4015.98 556.08
Pb|-------*Mb 8031.96 457.64 3212.78 526.86
| * 7228.76 494.10 2409.59 490.06
___________|____*_______ 6425.57 522.06 1606.39 448.19
| * M0 Mn, 5622.37 543.01 803.20 382.60
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
8 - 32 MM 1.072 1 END 0.650

--------------------------------------------------------
13051.93 10441.54 5197.36 4472.84 860.6
2506.02 -2661.63 404.92 15.41 0.01409
--------------------------------------------------------
--------------------------------------------------------
13051.93 10441.54 4170.10 560.62 134.4
305.71 -2661.63 404.92 2.64 0.00242
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 9638.35 2689.30 4819.17 4456.16
P0 |* 8835.15 3140.98 4015.98 4355.32
| * 8031.96 3523.84 3212.78 4187.02
Pn,max|__* 7228.76 3847.24 2409.59 3968.79
| * 6425.57 4121.69 1606.39 3652.48
Pn | * 5622.37 4358.61 803.20 3141.78
AXIAL| * 9638.35 353.92 4819.17 554.06
COMPRESSION| * 8835.15 412.44 4015.98 556.08
Pb|-------*Mb 8031.96 457.64 3212.78 526.86
| * 7228.76 494.10 2409.59 490.06
___________|____*_______ 6425.57 522.06 1606.39 448.19
| * M0 Mn, 5622.37 543.01 803.20 382.60
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
8 - 32 MM 1.072 1 END 0.650

--------------------------------------------------------
13051.93 10441.54 5197.36 4472.84 860.6
2506.02 -2661.63 282.58 15.49 0.02031
--------------------------------------------------------
--------------------------------------------------------
13051.93 10441.54 4170.10 560.62 134.4
305.71 -2661.63 282.58 2.93 0.00384
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 9638.35 2689.30 4819.17 4456.16
P0 |* 8835.15 3140.98 4015.98 4355.32
| * 8031.96 3523.84 3212.78 4187.02
Pn,max|__* 7228.76 3847.24 2409.59 3968.79
| * 6425.57 4121.69 1606.39 3652.48
Pn | * 5622.37 4358.61 803.20 3141.78
AXIAL| * 9638.35 353.92 4819.17 554.06
COMPRESSION| * 8835.15 412.44 4015.98 556.08
Pb|-------*Mb 8031.96 457.64 3212.78 526.86
| * 7228.76 494.10 2409.59 490.06
___________|____*_______ 6425.57 522.06 1606.39 448.19
| * M0 Mn, 5622.37 543.01 803.20 382.60
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
8 - 32 MM 1.072 1 END 0.650

--------------------------------------------------------
13051.93 10441.54 5197.36 4472.84 860.6
2506.02 -2661.63 160.75 155.19 0.35756
--------------------------------------------------------
--------------------------------------------------------
13051.93 10441.54 4170.10 560.62 134.4
305.71 -2661.63 160.75 2.10 0.00484
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 9638.35 2689.30 4819.17 4456.16
P0 |* 8835.15 3140.98 4015.98 4355.32
| * 8031.96 3523.84 3212.78 4187.02
Pn,max|__* 7228.76 3847.24 2409.59 3968.79
| * 6425.57 4121.69 1606.39 3652.48
Pn | * 5622.37 4358.61 803.20 3141.78
AXIAL| * 9638.35 353.92 4819.17 554.06
COMPRESSION| * 8835.15 412.44 4015.98 556.08
Pb|-------*Mb 8031.96 457.64 3212.78 526.86
| * 7228.76 494.10 2409.59 490.06
___________|____*_______ 6425.57 522.06 1606.39 448.19
| * M0 Mn, 5622.37 543.01 803.20 382.60
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.005 1 END 0.650

--------------------------------------------------------
10743.85 8595.08 4103.20 1990.50 485.1
932.91 -2079.40 230.09 6.37 0.01053
--------------------------------------------------------
--------------------------------------------------------
10743.85 8595.08 3847.39 930.91 242.0
428.45 -2079.40 230.09 0.96 0.00158
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7933.92 1160.92 3966.96 1985.88
P0 |* 7272.76 1357.77 3305.80 1933.31
| * 6611.60 1526.72 2644.64 1830.81
Pn,max|__* 5950.44 1671.77 1983.48 1678.35
| * 5289.28 1797.46 1322.32 1475.29
Pn | * 4628.12 1908.80 661.16 1215.46
AXIAL| * 7933.92 549.28 3966.96 923.80
COMPRESSION| * 7272.76 639.58 3305.80 907.53
Pb|-------*Mb 6611.60 717.01 2644.64 854.90
| * 5950.44 781.77 1983.48 771.74
___________|____*_______ 5289.28 836.12 1322.32 669.93
| * M0 Mn, 4628.12 882.57 661.16 553.68
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
12 - 32 MM 1.930 13 STA 0.650

--------------------------------------------------------
12575.94 10060.76 4286.53 2325.18 542.4
1745.36 -3992.45 655.82 1400.54 0.79094
--------------------------------------------------------
--------------------------------------------------------
12575.94 10060.76 3943.78 1080.98 274.1
786.87 -3992.45 655.82 173.14 0.09778
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 9286.85 1272.81 4643.43 2268.99
P0 |* 8512.95 1490.18 3869.52 2319.12
| * 7739.04 1685.19 3095.62 2288.40
Pn,max|__* 6965.14 1855.43 2321.71 2240.08
| * 6191.23 2006.09 1547.81 2109.74
Pn | * 5417.33 2142.80 773.90 1940.96
AXIAL| * 9286.85 591.29 4643.43 1036.04
COMPRESSION| * 8512.95 693.37 3869.52 1080.01
Pb|-------*Mb 7739.04 782.67 3095.62 1063.28
| * 6965.14 859.01 2321.71 1037.48
___________|____*_______ 6191.23 924.99 1547.81 977.21
| * M0 Mn, 5417.33 983.34 773.90 885.45
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.005 1 END 0.650

--------------------------------------------------------
10743.85 8595.08 4103.20 1990.50 485.1
932.91 -2079.40 299.36 6.97 0.00862
--------------------------------------------------------
--------------------------------------------------------
10743.85 8595.08 3847.39 930.91 242.0
428.45 -2079.40 299.36 5.09 0.00629
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7933.92 1160.92 3966.96 1985.88
P0 |* 7272.76 1357.77 3305.80 1933.31
| * 6611.60 1526.72 2644.64 1830.81
Pn,max|__* 5950.44 1671.77 1983.48 1678.35
| * 5289.28 1797.46 1322.32 1475.29
Pn | * 4628.12 1908.80 661.16 1215.46
AXIAL| * 7933.92 549.28 3966.96 923.80
COMPRESSION| * 7272.76 639.58 3305.80 907.53
Pb|-------*Mb 6611.60 717.01 2644.64 854.90
| * 5950.44 781.77 1983.48 771.74
___________|____*_______ 5289.28 836.12 1322.32 669.93
| * M0 Mn, 4628.12 882.57 661.16 553.68
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.005 1 END 0.650

--------------------------------------------------------
10743.85 8595.08 4103.20 1990.50 485.1
932.91 -2079.40 213.55 12.82 0.02223
--------------------------------------------------------
--------------------------------------------------------
10743.85 8595.08 3847.39 930.91 242.0
428.45 -2079.40 213.55 4.90 0.00849
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7933.92 1160.92 3966.96 1985.88
P0 |* 7272.76 1357.77 3305.80 1933.31
| * 6611.60 1526.72 2644.64 1830.81
Pn,max|__* 5950.44 1671.77 1983.48 1678.35
| * 5289.28 1797.46 1322.32 1475.29
Pn | * 4628.12 1908.80 661.16 1215.46
AXIAL| * 7933.92 549.28 3966.96 923.80
COMPRESSION| * 7272.76 639.58 3305.80 907.53
Pb|-------*Mb 6611.60 717.01 2644.64 854.90
| * 5950.44 781.77 1983.48 771.74
___________|____*_______ 5289.28 836.12 1322.32 669.93
| * M0 Mn, 4628.12 882.57 661.16 553.68
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.005 1 END 0.650

--------------------------------------------------------
10743.85 8595.08 4103.20 1990.50 485.1
932.91 -2079.40 127.28 12.96 0.03772
--------------------------------------------------------
--------------------------------------------------------
10743.85 8595.08 3847.39 930.91 242.0
428.45 -2079.40 127.28 2.06 0.00598
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7933.92 1160.92 3966.96 1985.88
P0 |* 7272.76 1357.77 3305.80 1933.31
| * 6611.60 1526.72 2644.64 1830.81
Pn,max|__* 5950.44 1671.77 1983.48 1678.35
| * 5289.28 1797.46 1322.32 1475.29
Pn | * 4628.12 1908.80 661.16 1215.46
AXIAL| * 7933.92 549.28 3966.96 923.80
COMPRESSION| * 7272.76 639.58 3305.80 907.53
Pb|-------*Mb 6611.60 717.01 2644.64 854.90
| * 5950.44 781.77 1983.48 771.74
___________|____*_______ 5289.28 836.12 1322.32 669.93
| * M0 Mn, 4628.12 882.57 661.16 553.68
| * BENDING
P-tens|* MOMENT
|


===============================================


----------------------------------------------------------
4 - 40 MM 1.005 1 END 0.650

--------------------------------------------------------
10743.85 8595.08 4103.20 1990.50 485.1
932.91 -2079.40 40.70 29.74 0.27066
--------------------------------------------------------
--------------------------------------------------------
10743.85 8595.08 3847.39 930.91 242.0
428.45 -2079.40 40.70 13.42 0.12215
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 7933.92 1160.92 3966.96 1985.88
P0 |* 7272.76 1357.77 3305.80 1933.31
| * 6611.60 1526.72 2644.64 1830.81
Pn,max|__* 5950.44 1671.77 1983.48 1678.35
| * 5289.28 1797.46 1322.32 1475.29
Pn | * 4628.12 1908.80 661.16 1215.46
AXIAL| * 7933.92 549.28 3966.96 923.80
COMPRESSION| * 7272.76 639.58 3305.80 907.53
Pb|-------*Mb 6611.60 717.01 2644.64 854.90
| * 5950.44 781.77 1983.48 771.74
___________|____*_______ 5289.28 836.12 1322.32 669.93
| * M0 Mn, 4628.12 882.57 661.16 553.68
| * BENDING
P-tens|* MOMENT
|
********************END OF COLUMN DESIGN RESULTS********************

CONCLUSIONES Y RECOMENDACIONES
El análisis se efectuó con el programa de análisis estructural

STAAD PRO, y la información de la geometría y ubicación de los
Elementos estructurales se obtuvieron de los planos de Arquitectura que fueron
entregados por el cliente.
Del análisis sísmico dinámico efectuado se obtuvieron distorsiones

en ambas direcciones menores al valor máximo permisible para
edificaciones de Concreto Armado (D/he ≤ 0.007), con lo cual el
edificio cumple con lo establecido en el Reglamento de Diseño
Sismorresistente E.030 (2018) del Reglamento Nacional de
Edificaciones.
Se diseñaron los elementos estructurales del Edificio con las normas

peruanas vigentes E.060 de concreto armado y norma Internacional ACI-
318
Se recomienda cumplir con las especificaciones técnicas y los

detalles que contempla los planos del proyecto.
_________________________________________________________________________________________

Memoria de Calculo - Estructuras

Cargado por

Copyright:

Formatos disponibles

Memoria de Calculo - Estructuras

Cargado por

Información del documento

Título original

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

Memoria de Calculo - Estructuras

Cargado por

Copyright:

Formatos disponibles

Memoria de Cálculo

Consorcio Casuarinas sac

Alberto Ordóñez Curotto, Ph.D.

12 de Agosto del 2022

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

El presente proyecto estructural “Edificio Multifamiliar” se encuentra ubicado en el

La presente memoria de cálculo corresponde al Proyecto Estructural “Edificio

2.1. OBJETIVOS ESPECÍFICOS

La presente memoria de cálculo tiene por objetivos específicos:

- Determinar el Sistema Estructural Sismorresistente utilizado en el proyecto

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

3.1 NORMAS NACIONALES

Se sigue las disposiciones del Reglamento Nacional de Edificaciones (RNE):

Norma Internacional ACI 318R-14.

4.1. CONDICIONES DE MECÁNICA DE SUELOS

Del Estudio de Mecánica de Suelos obtenemos lo siguiente:

Factores para el empuje de suelos: Ka = 0.29 Kp = 3.96

Resistencia admisible = 4.00 kg/cm2

4.2. ESPECIFICACIONES TECNICAS DE MATERIALES

4.2.2 ACERO DE REFUERZO GRADO 60:

4.3.1 ALBAÑILERIA CONFINADA:

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

Se han considerado los siguientes tipos de carga:

CARGAS MUERTAS (D):

- Peso de elementos de concreto armado : 2400 kg/m3

CARGAS VIVAS (L):

CARGAS DE SISMO (S):

CARGAS POR EMPUJES LATERALES DEL TERRENO (H):

- Presión lateral dinámica :

CARGAS POR PRESION DE LIQUIDOS (F):

4.4. COMBINACIONES DE CARGAS

La resistencia requerida de los elementos y sus conexiones fueron determinadas

Se tuvieron en cuenta las combinaciones de cargas factorizadas recomendadas por el

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

5.1.1. Sistema de Muros Estructurales en la dirección X y Z.

5.1.2. Número de pisos proyectados

El proyecto contempla la construcción de un semisótano y 5 pisos, la altura de piso a

5.2. PREDIMENSIONAMIENTO DE ELEMENTOS ESTRUCTURALES

5.2.1. ELEMENTOS DE CONCRETO ARMADO f’c = 210 Kg/cm2

- Vigas principales y secundarias:

H = L/12; H = 7.0/12 = 0.58 m. Consideramos H=0.55 m.

B = H/2; H = 0.55/2 = 0.275 m.

Columna centrada: Acol = Pserv / 0.45f’c

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com

Dimensiones de la columna 25 cm x 100 cm

Vigas = Rv = 25x55^3/(12x700) = 495 cm3

Columnas Rc = 25x160^3/(12/270) = 31,605 cm3

Caso más desfavorable Rc /2 Rv = 31,605/990 = 31.92 > 1.2 OK

Según ACI 318:14 - 8.3.1.2: Losa Aligerada unidireccional

Ll=Luz libre mayor =5.00 m. H = 500/25 = 20 cm

6.0. ANÁLISIS ESTRUCTURAL

6.6.1. PARÁMETROS SISMICOS

El análisis sísmico se desarrolló de acuerdo con las indicaciones de la Norma Peruana

U = Factor de Uso o de importancia.

S = Factor del suelo.

C = Coeficiente sísmico, según el periodo.

g = valor de la aceleración de la gravedad.

T = Aceleración del suelo

[email protected] [email protected] 51-1-457-7311 / 51-1-997-203-105 www.alboric.com