Este documento proporciona información técnica sobre el actuador de retorno de resorte TFB120. El actuador funciona con 100-240 V de CA, produce un par de giro de 22 in-lb, tiene un ángulo de rotación ajustable de hasta 95 grados, y proporciona una operación segura de retorno de resorte para aplicaciones antiincendio. El actuador está diseñado para acoplarse directamente a un eje de compuerta entre 1/4 y 1/2 pulgadas de diámetro.
0 calificaciones0% encontró este documento útil (0 votos)
15 vistas4 páginas
Este documento proporciona información técnica sobre el actuador de retorno de resorte TFB120. El actuador funciona con 100-240 V de CA, produce un par de giro de 22 in-lb, tiene un ángulo de rotación ajustable de hasta 95 grados, y proporciona una operación segura de retorno de resorte para aplicaciones antiincendio. El actuador está diseñado para acoplarse directamente a un eje de compuerta entre 1/4 y 1/2 pulgadas de diámetro.
Este documento proporciona información técnica sobre el actuador de retorno de resorte TFB120. El actuador funciona con 100-240 V de CA, produce un par de giro de 22 in-lb, tiene un ángulo de rotación ajustable de hasta 95 grados, y proporciona una operación segura de retorno de resorte para aplicaciones antiincendio. El actuador está diseñado para acoplarse directamente a un eje de compuerta entre 1/4 y 1/2 pulgadas de diámetro.
Este documento proporciona información técnica sobre el actuador de retorno de resorte TFB120. El actuador funciona con 100-240 V de CA, produce un par de giro de 22 in-lb, tiene un ángulo de rotación ajustable de hasta 95 grados, y proporciona una operación segura de retorno de resorte para aplicaciones antiincendio. El actuador está diseñado para acoplarse directamente a un eje de compuerta entre 1/4 y 1/2 pulgadas de diámetro.
Descargue como PDF, TXT o lea en línea desde Scribd
Descargar como pdf o txt
Está en la página 1/ 4
Technical data sheet TFB120
On/Off, Spring Return, AC 100...240 V
Technical data
Electrical data Nominal voltage AC 100...240 V
Nominal voltage frequency 50/60 Hz Nominal voltage range AC 85...265 V Power consumption in operation 2.5 W Power consumption in rest position 1.3 W Transformer sizing 5 VA Electrical Connection 18 GA appliance cable, 1 m, with 1/2" conduit connector Overload Protection electronic throughout 0...95° rotation Electrical Protection actuators are double insulated
Functional data Torque motor 22 in-lb [2.5 Nm]
Direction of motion motor selectable by ccw/cw mounting Direction of motion fail-safe reversible with cw/ccw mounting Angle of rotation Max. 95° Angle of rotation note adjustable with mechanical stop Running Time (Motor) 75 s Running time fail-safe <25 s @ -4...122°F [-20...50°C], <60 s @ -22°F [-30°C] Noise level, motor 50 dB(A) Noise level, fail-safe 62 dB(A) Position indication Mechanical
Safety data Degree of protection IEC/EN IP42
Degree of protection NEMA/UL NEMA 2 Enclosure UL Enclosure Type 2 Agency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSA E60730-1:02 CE acc. to 2014/30/EU and 2014/35/EU Quality Standard ISO 9001 UL 2043 Compliant Suitable for use in air plenums per Section 300.22(C) of the NEC and Section 602 of the IMC Ambient humidity Max. 95% RH, non-condensing Ambient temperature -22...122°F [-30...50°C] Storage temperature -40...176°F [-40...80°C] Servicing maintenance-free
Weight Weight 1.6 lb [0.74 kg]
Materials Housing material UL94-5VA
Footnotes †Rated Impulse Voltage 4kV, Type of action 1.AA, Control Pollution Degree 3.
Application For On/Off, fail-safe control of dampers in HVAC systems. Actuator sizing should be done in accordance with the damper manufacturer’s specifications. Control is On/Off from an auxiliary contact, or a manual switch. The actuator is mounted directly to a damper shaft from 1/4” up to 1/2” in diameter by means of its universal clamp, 1/2” shaft centered at delivery. A crank arm and several mounting brackets are available for applications where the actuator cannot be direct coupled to the damper shaft.
Operation The TF series actuators provide true spring return operation for reliable fail-safe application and positive close off on air tight dampers. The spring return system provides consistent torque to the damper with, and without, power applied to the actuator. The TF series provides 95° of rotation and is provided with a graduated position indicator showing 0° to 90°. The actuator may be stalled anywhere in its normal rotation without the need of mechanical end switches. Power consumption is reduced in holding mode. The actuator is double insulated so an electrical ground connection is not necessary. Safety Note: Screw a conduit fitting into the actuator’s bushing. Jacket the actuator’s input and output wiring with suitable flexible conduit. Properly terminate the conduit in a suitable junction box.
Typical specification On/Off spring return damper actuators shall be direct coupled type which require no crank arm and linkage and be capable of direct mounting to a shaft up to a 1/2” diameter and center a 1/2” shaft. The actuators must be designed so that they may be used for either clockwise or counter clockwise fail-safe operation. Actuators shall be protected from overload at all angles of rotation. If required, one SPDT auxiliary switch shall be provided having the capability of being adjustable. Actuators with auxiliary switch must be constructed to meet the requirements for Double Insulation so an electrical ground is not required to meet agency listings. Actuators shall be cULus listed, have a 5 year warranty, and be manufactured under ISO 9001 International Quality Control Standards. Actuators shall be as manufactured by Belimo.
Accessories
Electrical accessories Description Type
Auxiliary switch, mercury-free P475 Auxiliary switch, mercury-free P475-1 Signal simulator, Power supply AC 120 V PS-100 Cable conduit connector 1/2" TF-CC US
Shaft extension 170 mm Ø10 mm for damper shaft Ø 6...16 mm AV6-20 Position indicator IND-TF for TFB(X) Shaft clamp K8 US for TFB(X) Ball joint suitable for damper crank arm KH8 / KH10, Multipack 10 pcs. KG10A Ball joint suitable for damper crank arm KH8, Multipack 10 pcs. KG6 Ball joint suitable for damper crank arm KH8, Multipack 10 pcs. KG8 Damper crank arm Slot width 8.2 mm, for Ø1.05" KH12 Damper crank arm Slot width 6.2 mm, clamping range Ø10...18 mm KH6 Damper crank arm Slot width 8.2 mm, clamping range Ø10...18 mm KH8 TFB(X) crankarm with 5/16" slot. KH-TF US TFB(X) crankarm with 1/4" slot. KH-TF-1 US Screw fastening kit SB-TF Push rod for KG10A ball joint 36” L, 3/8” diameter SH10 Push rod for KG6 & KG8 ball joints (36” L, 5/16” diameter). SH8 Anti-rotation bracket TF/NKQ/AM/NM/LM. TF-P Wrench 0.32 in and 0.39 in [8 mm and 10 mm] TOOL-06 Angle of rotation limiter, with end stop ZDB-TF Mounting bracket ZG-113 for TFB(X) Damper clip for damper blade, 3.5” width. ZG-DC1 Damper clip for damper blade, 6” width. ZG-DC2 Shaft extension for 3/8" diameter shafts (4" L). ZG-LMSA-1 Shaft extension for 1/2" diameter shafts (5" L). ZG-LMSA-1/2-5 TFB(X) crankarm adaptor kit (includes ZG-113). ZG-TF112 TFB(X) crankarm adaptor kit (T bracket included). ZG-TF2 Mounting kit ZG-TF3 for TFB(X) Weather shield 330x203x152 mm [13x8x6"] (LxBxH) ZS-100 Base plate, for ZS-100 ZS-101 Weather shield 406x213x102 mm [16x8-3/8x4"] (LxWxH) ZS-150
Electrical installation
Warning! Live electrical components!
During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Meets cULus requirements without the need of an electrical ground connection. Actuators with appliance cables are numbered. Provide overload protection and disconnect as required. Actuators may be connected in parallel if not mechanically linked. Power consumption and input impedance must be observed.
