Connect Ideastatica Salida

Proyecto:
Proyecto nº:
Autor:
Datos del proyecto

Nombre del proyecto
Número del Proyecto
Autor
Descripción
Fecha 21-08-2019
Normativa de cálculo AISC 360-16
Material
Acero A36
Proyecto:
Proyecto nº:
Autor:
Ítem del proyecto CONEXION-9B-3
Diseño
Nombre CONEXION-9B-3
Descripción VIGAS
Análisis Resistencia de diseño de la unión
Normativa de cálculo AISC - ASD
Elementos estructurales
β– γ- α- Desplazamiento Desplazamiento Desplazamiento
Fuerzas
Nombre Sección transversal Dirección Inclinación Rotación ex ey ez
en
[°] [°] [°] [cm] [cm] [cm]
2-
B1 0.0 0.0 0.0 0.500 0.000 0.000 Nudo
HN400x172(Iw400x400)
2-
B2 180.0 0.0 0.0 0.500 0.000 0.000 Nudo
HN400x172(Iw400x400)
Secciones
Nombre Material
2 - HN400x172(Iw400x400) A36
Tornillos
Diámetro fu Área bruta
Nombre Conjunto de tornillo
[cm] [MPa] [cm2]
7/8 A325 7/8 A325 2.223 825.0 3.880
Proyecto:
Proyecto nº:
Autor:
Cargas
N Vy Vz Mx My Mz
Nombre Elemento
[kN] [kN] [kN] [kNm] [kNm] [kNm]
B033_ASD05D_E+_Z+ B1 -19.241 -55.073 -113.518 -6.22 -89.90 -59.10
B027_ASD05D_[Pope... B1 19.676 67.030 108.449 6.45 57.87 -11.88
B031_ASD05D_E+_Z- B1 -12.440 -73.248 -107.714 -2.95 -149.20 -37.79
B021_ASD05D_[Pope... B1 12.875 85.204 102.645 3.18 117.16 -33.18
B021_ASD05D_[Pope... B1 -18.788 -53.088 -115.353 -6.18 -87.90 -61.78
B035_ASD05D_E+_Z- B1 19.223 65.045 110.075 6.41 53.30 -10.02
B039_ASD06A_[Pope... B1 -7.146 -8.535 -63.627 -6.84 -17.77 -35.18
B008_ASD05A_T-_[P... B1 6.430 23.121 56.544 7.13 -11.10 -37.47
B065_ASD05D_[Pope... B1 -7.651 -0.924 -45.918 -0.18 -9.55 -129.58
B015_ASD05D_[Pope... B1 10.856 0.924 41.162 0.17 9.55 44.26
B065_ASD05D_[Pope... B1 -12.021 -68.202 -110.271 -2.86 -161.08 -59.78
B015_ASD05D_[Pope]_E+_Z- B1 12.666 81.675 104.015 3.12 128.92 -11.13
Verificación
Resumen
Nombre Valor Estado de la verificación
Placas 0.1 < 5% Aceptar
Tornillos 19.8 < 100% Aceptar
Placas
Fy Espesor σEd εPl
Nombre Cargas Estado de la verificación
[MPa] [mm] [MPa] [%]
B1-tfl 1 248.2 22.00 B065_ASD05D_[Pope... 122.2 0.1 Aceptar
B1-bfl 1 248.2 22.00 B065_ASD05D_[Pope... 125.9 0.1 Aceptar
B1-w 1 248.2 12.00 B065_ASD05D_[Pope... 105.7 0.0 Aceptar
B2-tfl 1 248.2 22.00 B065_ASD05D_[Pope... 122.4 0.1 Aceptar
B2-bfl 1 248.2 22.00 B065_ASD05D_[Pope... 126.8 0.1 Aceptar
B2-w 1 248.2 12.00 B065_ASD05D_[Pope... 73.6 0.0 Aceptar
SPL1a 248.2 16.00 B065_ASD05D_[Pope... 124.0 0.1 Aceptar
SPL1b 248.2 16.00 B065_ASD05D_[Pope... 120.1 0.0 Aceptar
SPL1c 248.2 16.00 B065_ASD05D_[Pope... 104.0 0.0 Aceptar
SPL2c 248.2 16.00 B065_ASD05D_[Pope... 96.8 0.0 Aceptar
Datos de diseño
fy εlim
Material
[MPa] [%]
A36 248.2 5.0
Explicación del símbolo

εPl Deformación plástica
σEd Ec. tensión
fy Límite elástico
εlim Límite de la deformación plástica
Proyecto:
Proyecto nº:
Autor:
Verificación general, B065_ASD05D_[Pope...
Verificación de deformación, B065_ASD05D_[Pope...

Proyecto:
Proyecto nº:
Autor:
Tensión equivalente, B065_ASD05D_[Pope...

Proyecto:
Proyecto nº:
Autor:
Tornillos
Ft V Rn/ΩPortante Utt Uts Utts
Forma Ítem Calidad Cargas Detallado Estado
[kN] [kN] [kN] [%] [%] [%]
B1 7/8 A325 - 1 B021_ASD05D_[Pope... 3.449 5.814 234.749 2.9 8.1 - Aceptar Aceptar
B13 7/8 A325 - 1 B031_ASD05D_E+_Z- 3.689 4.849 110.118 3.1 6.7 - Aceptar Aceptar
Proyecto:
Proyecto nº:
Autor:
Ft V Rn/ΩPortante Utt Uts Utts

Forma Ítem Calidad Cargas Detallado Estado
[kN] [kN] [kN] [%] [%] [%]
B64 7/8 A325 - 1 B008_ASD05A_T-_[P... 0.363 1.369 104.875 0.3 1.9 - Aceptar Aceptar
Datos de diseño
Rn/ΩTracción Rn/ΩCortante
Calidad
[kN] [kN]
7/8 A325 - 1 120.265 72.159
Explicación del símbolo

Ft Fuerza de tracción
V Resultante de las fuerzas cortantes Vy, Vz en el tornillo.
Rn/ΩPortante Resistencia a aplastamiento de la chapa provocado por el tornillo
Utt Utilización a tracción
Uts Utilización a cortante
Utts Utilización a tensión y cortante
Rn/ΩTracción Resistencia de los tornillos a tracción, según AISC 360-10 tabla J3.2
Rn/ΩCortante Resistencia de los tornillos a cortante, según AISC 360-16 tabla J3.2
Resultado detallado para B1

Comprobación de la resistencia a tracción (AISC 360-16: J3-1)
Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 3.449 kN
Donde:
Fnt = 620.0 MPa – resistencia a tracción nominal de AISC 360-16 Tabla J3.2
Ab = 3.880 cm2 – Área bruta del tornillo
Ω = 2.00 – factor de seguridad para tracción y cortante
Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.814 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Fnv = 372.0 MPa – resistencia a tensiones tangenciales de AISC 360-16 Tabla J3.2
Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.310 kN
Donde:
lc = 13.744 cm – distancia libre, en la dirección de la fuerza, entre el borde del agujero y el borde del agujero adyacente o borde del
material
t = 2.200 cm – espesor de la placa
d = 2.223 cm – dimámetro del tornillo
Fu = 400.0 MPa – resistencia a tracción del material conectado
Ω = 2.00 – factor de resistencia para aplastamiento en los agujeros para tornillos
Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

La tensión requerida, a cortante o en tracción, es menor o igual al 30% de la resistencia y los efectos de las tensiones combinadas no necesitan
ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.473 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.761 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 9.686 kN
Donde:
material
– factor de resistencia para aplastamiento en los agujeros para tornillos
Proyecto:
Proyecto nº:
Autor:
Ω = 2.00

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.315 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 6.138 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.253 kN
Donde:
material

ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.347 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.972 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 17.810 kN
Donde:
material

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.416 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.089 kN
Donde:
– Área bruta del tornillo
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 16.115 kN
Donde:
material

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.790 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.120 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 18.191 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.945 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.339 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 148.673 kN ≥ V = 14.334 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.255 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 7.247 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.016 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 2.290 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.864 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.810 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.768 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.359 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 164.261 kN ≥ V = 18.594 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.269 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 8.935 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 17.171 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.967 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.616 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 18.839 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 3.689 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 4.849 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 110.118 kN ≥ V = 9.118 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.342 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 5.139 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.060 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.314 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.330 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.423 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.320 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.980 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 17.954 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.405 kN
Donde:

Proyecto:
Proyecto nº:
Autor:
Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.142 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 16.252 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.809 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.254 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 18.354 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 3.429 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.607 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 110.708 kN ≥ V = 15.401 kN
Donde:
material


ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.626 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.988 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.206 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 2.211 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.186 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.806 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.730 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.651 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 102.097 kN ≥ V = 20.224 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.319 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.256 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 19.224 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 2.468 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 10.636 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 20.080 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 3.989 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.373 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.584 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.579 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.578 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.609 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.496 kN
Donde:

Proyecto:
Proyecto nº:
Autor:
Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.316 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 15.665 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.438 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.592 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 19.171 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.410 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 9.520 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 18.257 kN
Donde:
material


ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.722 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.327 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 19.360 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.939 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.783 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 160.569 kN ≥ V = 10.502 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.153 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.623 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 9.715 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.616 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.940 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.234 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.744 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 8.759 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 167.549 kN ≥ V = 17.353 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.315 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.765 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 15.501 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.733 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.810 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 17.596 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 4.755 kN
Donde:

Proyecto:
Proyecto nº:
Autor:
Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.364 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 15.209 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.844 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.012 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 14.624 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.494 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.420 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 15.578 kN
Donde:
material


ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.736 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.625 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 20.339 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.396 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.305 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 19.564 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.774 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 10.868 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 20.663 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 3.265 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.294 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 95.625 kN ≥ V = 10.374 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.680 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 5.141 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.234 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.596 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 5.263 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 10.497 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.736 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.746 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 110.041 kN ≥ V = 17.472 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.328 kN
Donde:

Proyecto:
Proyecto nº:
Autor:
Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 7.826 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 15.610 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 1.768 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 8.955 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 234.749 kN ≥ V = 17.696 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.210 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 2.918 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 5.827 kN
Donde:
material


ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.040 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 0.775 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 1.483 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.176 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.149 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.249 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.522 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 4.266 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 8.416 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.192 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 3.050 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 5.784 kN
Donde:
material

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.280 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 3.157 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 5.955 kN
Donde:
material

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.713 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 4.204 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 8.176 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.296 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 3.094 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 5.743 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.587 kN
Donde:

Proyecto:
Proyecto nº:
Autor:
Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 3.283 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 6.149 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.073 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.307 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.590 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.053 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 0.806 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 1.550 kN
Donde:
material

ser evaluadas.
Proyecto:
Proyecto nº:
Autor:

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.144 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.391 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.714 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.143 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.432 kN
Donde:
Proyecto:
Proyecto nº:
Autor:
Ab = 3.880 cm2
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.826 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.079 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.056 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.035 kN
Donde:
material
Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.427 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.510 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.841 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.363 kN
Donde:

R A
Rn Fnv ⋅Ab
Ω =
Proyecto:
Ω = 72.159 kN ≥ V = 1.369 kN
Proyecto nº:
Donde:
Autor:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 104.875 kN ≥ V = 2.507 kN
Donde:
material


ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.218 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.187 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.178 kN
Donde:
material

Proyecto:
Proyecto nº:
Autor:

ser evaluadas.

Rn Fnt ⋅Ab
Ω = Ω = 120.265 kN ≥ Ft = 0.207 kN
Donde:

Rn Fnv ⋅Ab
Ω = Ω = 72.159 kN ≥ V = 1.482 kN
Donde:
Rn = 1.20 ⋅ lc ⋅ t ⋅ Fu ≤ 2.40 ⋅ d ⋅ t ⋅ Fu
Rn
Ω = 128.045 kN ≥ V = 2.801 kN
Donde:
material

ser evaluadas.
Configuración de la norma
Ítem Valor Unidad Referencia
Coeficiente de fricción - hormigón 0.40 - ACI 349 – B.6.1.4
Coeficiente de fricción en la resistencia a deslizamiento 0.30 - AISC 360-16 – J3.8
Deformación plástica límite 0.05 -
Redistribución
Evaluación de la tensión de la soldadura
plástica
Detallado Sí
Proyecto:
Proyecto nº:
Autor:
Ítem Valor Unidad Referencia

Distancia entre tornillos [d] 2.66 - AISC 360-16 – J3.3
Distancia entre tornillos y el borde [d] 1.25 - AISC 360-16 – J.3.4
Resistencia al arrancamiento del cono de hormigón Sí
Resistencia del metal base en la cara de fusión de la
Sí AISC 360-16 – J2-2
soldadura
Hormigón fisurado Sí ACI 318-14 – Chapter 17
Comprobación de la deformación local Sí
Deformación límite local 0.03 - CIDECT DG 1, 3 - 1.1
Grandes deformaciones para secciones
No linealidad geométrica (GMNA) Sí
huecas
Braced system No
Proyecto:
Proyecto nº:
Autor:
Theoretical Background
CBFEM versus Component method
The weak point of standard Component method is in analyzing of internal forces and stress in a joint. CBFEM replaces specific analysis of internal
forces in joint with general FEA.
Check methods of specific components like bolts or welds are done according to standard Component method (Eurocode).
For the fasteners – bolts and welds – special FEM components had to be developed to model the welds and bolts behaviour in joint. All parts of 1D
members and all additional plates are modelled as plate/walls. These elements are made of steel (metal in general) and the behaviour of this
material is significantly nonlinear.
The real stress-strain diagram of steel is replaced by the ideal plastic material for design purposes in building practice. The advantage of ideal
plastic material is, that only yield strength and modulus of elasticity must be known to describe the material curve. The granted ductility of
construction steel is 15 %. The real usable value of limit plastic strain is 5% for ordinary design (1993-1-5 appendix C paragraph C.8 note 1).
The stress in steel cannot exceed the yield strength when using the ideal elastic-plastic stress-strain diagram.
Real tension curve and the ideal elastic-plastic diagram of material
CBFEM method aims to model the real state precisely. Meshes of plates / walls are not merged, no intersections are generated between them,
unlike it is used to when modelling structures and buildings. Mesh of finite elements is generated on each individual plate independently on mesh of
other plates.
Between the meshes, special massless force interpolation constraints are added. They ensure the connection between the edge of one plate and
the surface or edge of the other plate.
This unique calculation model provides very good results – both for the point of view of precision and of the analysis speed. The method is protected
by patent.
The steel base plate is placed loosely on the concrete foundation. It is a contact element in the analysis model – the connection resists compression
fully, but does not resist tension.
Stress-strain diagram of contact between the concrete block and the base plate
Welds are modelled using a special elastoplastic element, which is added to the interpolation links between the plates. The element respects the
Proyecto:
weld throat thickness, position and orientation. The plasticity state is controlled by stresses in the weld throat section. The plastic redistribution of
Proyecto
stress nº: allows for stress peaks to be redistributed along the longer part of the weld.
in welds
Autor:
Bolted connection consists of two or more clasped plates and one or more bolts. Plates are placed loosely on each other.
A contact element is inserted between plates in the analysis model, which acts only in compression. No forces are carried in tension.
Shear force is taken by bearing. Special model for its transferring in the force direction only is implemented. IDEA StatiCa Connection can check
bolts for interaction of shear and tension. The bolt behavior is implemented according to the following picture.
Bolt – tension
Symbols explanation:
K – linear stiffness of bolt,

Kp – stiffness of bolt at plastic branch,
Flt – limit force for linear behaviour of bolt,
Ft,Rd – limit bolt resistance,
ul – limit deformation of bolt.
Bolt – interaction of shear and tension
The concrete block in CBFEM is modelled using Winkler-Pasternak subsoil model. The stiffness of subsoil is determined using modulus of elasticity
of concrete and effective height of subsoil. The concrete block is not designed by CBFEM method.
Proyecto:
Proyecto nº:
Autor:
Loads
End forces of member of the frame analysis model are transferred to the ends of member segments. Eccentricities of members caused by the joint
design are respected during load transfer.
The analysis model created by CBFEM method corresponds to the real joint very precisely, whereas the analysis of internal forces is performed on
very idealised 3D FEM 1D model, where individual beams are modelled using centrelines and the joints are modelled using immaterial nodes.
Joint of a vertical column and a horizontal beam
Internal forces are analysed using 1D members in 3D model. There is an example of courses of internal forces in the following picture.
Internal forces in horizontal beam. M and V are the end forces at joint.
The effects caused by member on the joint are important to design the joint (connection). The effects are illustrated in the following picture.
Effects of the member on the joint. CBFEM model is drawn in dark blue color.
Moment M and shear force V act in a theoretical joint. The point of theoretical joint does not exist in CBFEM model, thus the load cannot be applied
here. The model must be loaded by actions M and V, which have to be transferred to the end of segment in the distance r.
Proyecto:
Proyecto nº:
Autor:
Mc = M − V · r
Vc = V
In CBFEM model, the end section of segment is loaded by moment Mc and force Vc.
Welds
Fillet welds
The design strength, ϕRn and the allowable strength, Rn/Ω of welded joints are evaluated in connection weld check.
ϕ = 0.75 (LRFD)
Ω = 2.00 (ASD)
Available strength of welded joints is evaluated according to AISC 360-16 – J2.4:
Rn = FnwAwe
Fnw = 0.60 FEXX (1.0 + 0.50 sin1.5Θ)
where
F nw – nominal stress of weld material,

A we – effective area of the weld,
F EXX – electrode classification number, i.e., minimum specified tensile strength,
Θ – angle of loading measured from the weld longitudinal axis.
For end-loaded fillet welds with a length up to 100 times the weld size, it is permitted to take the effective length equal to the actual length. When the
length of the end-loaded fillet weld exceeds 100 times the weld size, the effective length shall be determined by multiplying the actual length by the
reduction factor, β.
β = 1.2 − 0.002 (L / Ls)
where:
L – weld length,
L s – weld leg size.
When the length of the weld exceeds 300 times the leg size, Ls, the effective length is taken as 180 Ls.
Base metal strength is evaluated if the option is selected in Code setup (Base metal capacity at the fusion face).
CJP groove welds

AISC Specification Table J2.5 identifies four loading conditions that might be associated with JP groove welds, and shows that the strength of the
joint is either controlled by the base metal or that the loads need not be considered in the design of the welds connecting the parts. Accordingly,
when CJP groove welds are made with matching-strength filler metal, the strength of a connection is governed or controlled by the base metal, and
no checks on the weld strength are required.
Bolts
Tensile and shear strength of bolts
The design tensile or shear strength, ϕRn, and the allowable tensile or shear strength, Rn / Ω of a snug-tightened bolt is determined according to the
limit states of tension rupture and shear rupture as follows:
Rn = FnAb
ϕ = 0.75 (LRFD)
Ω = 2.00 (ASD)
where
A b – nominal unthreaded body area of bolt or threaded part,

F n – nominal tensile stress, Fnt, or shear stress, Fnv, from Table J3.2.
The tensile force, against which the required tensile strength is checked, includes any tension resulting from prying action produced by deformation
of the connected parts.
Proyecto:
Proyecto nº:
Autor:
Combined Tension and shear in bearing type connection

The available tensile strength of a bolt subjected to combined tension and shear is determined according to the limit states of tension and shear
rupture as follows:
Rn = F'ntAb (AISC 360-16 J3-2)
ϕ = 0.75 (LRFD)
Ω = 2.00 (ASD)
F'nt = 1.3 Fnt − frvFnt / ϕFnv (AISC 360-16 J3-3a LRFD)
F'nt = 1.3 Fnt − frvΩ Fnt / Fnv (AISC 360-16 J3-3b ASD)
where
F' nt – nominal tensile stress modified to include the effects of shear stress,
F nt – nominal tensile stress from AISC 360-16 – Tab. J3.2,
F nv – nominal shear stress from AISC 360-16 – Tab. J3.2,
f rv – required shear stress using LRFD or ASD load combinations. The available shear stress of the fastener shall be equal or exceed the
required shear stress, frv.
Bearing strength in bolt holes

The available bearing strength, ϕRn and Rn/Ω at bolt holes is determined for the limit state of bearing as follows:
For a bolt in a connection with standard holes:
Rn = 1.2 lctFu ≤ 2.4 d t Fu (AISC 360-16 J3-6a, c)
For a bolt in a connection with slotted holes:
Rn = 1.0 lct Fu ≤ 2.0 d t Fu (AISC 360-16 J3-6e, f)
ϕ = 0.75 (LRFD)
Ω = 2.00 (ASD)
where
F u – specified minimum tensile strength of the connected material,

d – nominal bolt diameter,
l c – clear distance, in the direction of the force, between the edge of the hole and the edge of the adjacent hole or edge of the material,
t – thickness of connected material.
Preloaded bolts
The design slip resistance of a preloaded class A325 or A490 bolt with of effect of tensile force, Ft,Ed according to AISC 360-16 – J3.9.
Preloading force to be used AISC 360-16 – Tab. J3.1.
Tb = 0.7 fubAs
Design slip resistance per bolt AISC 360-16 – J3.8
Rn = 1.13 μ TbNs
Utilisation in shear [%]:
Uts = V / Rn
where
A s – tensile stress area of the bolt,

f ub – ultimate tensile strength,
μ – mean slip factor coefficient,
N s – number of the friction surfaces. Check is calculated for each friction surface separately,
V – shear force.
Anchors
The anchor bolt element is elastic-plastic with significant strain hardening. The maximum steel tensile resistance is expected at the strain which
equals to 0.25 × guaranteed elongation. The failure mode due to concrete cracking may occur before the anchor steel tensile resistance is reached
and is considered as a completely brittle failure.
Similarly, the steel components in shear (anchor bolt, base plate in bearing) are able to yield but failure modes connected with concrete cracking
may occur suddenly as a brittle failure.
All standards use Concrete Capacity Design method developed by prof. R. Eligehausen at University of Stuttgart. The theory is based on vast
experimental and numerical testing mostly on unreinforced concrete blocks and relatively short, often post-installed, anchors.
Anchorage is designed according to ACI 318-14 – Chapter 17. The design is available only for LRFD. Some failure modes (e.g. steel resistance) are
evaluated for single anchors, others (e.g. concrete breakout) are checked for group of anchors.
Información del programa

Aplicación IDEA StatiCa Connection
Versión 10.1.117.55848
Desarrollado por Idea StatiCa

Connect Ideastatica Salida

Cargado por

Copyright:

Formatos disponibles

Connect Ideastatica Salida

Cargado por

Información del documento

Título original

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

Connect Ideastatica Salida

Cargado por

Copyright:

Formatos disponibles

Proyecto:

Datos del proyecto

Ítem del proyecto CONEXION-9B-3

Explicación del símbolo

Verificación general, B065_ASD05D_[Pope...

Verificación de deformación, B065_ASD05D_[Pope...

Tensión equivalente, B065_ASD05D_[Pope...

Ft V Rn/ΩPortante Utt Uts Utts

Explicación del símbolo

Resultado detallado para B1

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B2

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B3

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B4

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B5

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B6

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

d = 2.223 cm – dimámetro del tornillo

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B7

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Fu = 400.0 MPa – resistencia a tracción del material conectado

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B8

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

Fu = 400.0 MPa – resistencia a tracción del material conectado

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B9

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)

d = 2.223 cm – dimámetro del tornillo

Fu = 400.0 MPa – resistencia a tracción del material conectado

Comprobación de la interacción tracción-cortante (AISC 360-16: J3-2)

Resultado detallado para B10

Ω = 2.00 – factor de seguridad para tracción y cortante

Comprobación de la resistencia a cortante (AISC 360-16: J3-1)

Comprobación de resitencia a aplastamiento (AISC 360-16: J3-6)