Scribd
Cargar
95 vistas1 página

Criterio VT AWS D1.1

Criterio Inspección Visual

Cargado por

Oscar
Derechos de autor
© © All Rights Reserved
Nos tomamos en serio los derechos de los contenidos. Si sospechas que se trata de tu contenido, reclámalo aquí.
Formatos disponibles
Descarga como PDF o lee en línea desde Scribd
95 vistas1 página

Criterio VT AWS D1.1

Criterio Inspección Visual

Cargado por

Oscar
Derechos de autor
© © All Rights Reserved
Nos tomamos en serio los derechos de los contenidos. Si sospechas que se trata de tu contenido, reclámalo aquí.
Formatos disponibles
Descarga como PDF o lee en línea desde Scribd
Está en la página 1/ 1
‘AWS D1.1/01.1M:2020, CLAUSE 8. INSPECTION Table 8.1 Visual Inspection Acceptance Criteria (see 8.9) Staicaly Loaded | Cyclically Loaded Nontubular ‘Nontubular Discontinuity Category and Inspection Criteria Connections | __Connections (0) Crack Probibition x x Any crack shall be unacceptable, regardless of size or (2) Weld/Base Metal Fusion ‘Complete fusion shall exist between adjacent layers of weld metal and between weld x x metal and base metal (@) Crater Cross Section ‘All craters shall be filled to provide the specified weld size, except forthe ends of x x interment fillet welds outside of ther effective Teng @ Weld Profites x x Weld profiles shall e in conformance with 2.23, (6) Time of Inspection Visual inspection of welds in all steels may begin immediately after the completed welds have cooled to ambient temperature. Acceptance criteria for ASTM ASL4, ASI7, and x x ‘A709 Grade HPS 100W [HPS 690W] stels shall be based on visual inspection performed not less than 48 hours after completion of the weld (© Undersized Welds The size ofa fillet weld in any continuous weld may be less than the specified nominal ‘Sie (L) without correction by the following amounts (U}: L. v specified nominal weld size, in [mm] allowable decrease from L. in (mum 3/16 (5) < W162 x x a6] £382 [25] > 5/16 (8) V8 (3) {Ina cases, the undersize portion ofthe weld shall not exceed 10% of the weld length ‘On web-to lange welds on girders, underrun shal be prohibited atthe ends for a length esqal to twice the width ofthe flange (0) Undercut (A) For material less than 1 in (25 mm) thick, undercut shall not exceed 1/32 in (1 am), ‘vith the following exception undercut shall not exceed 1/16 in [2 mm] for any accumlated x length up o 2 in [50 am] in any 12 in (300 man). For material equal to or greater than 1 in [25 mm} thick, undercut shall not exceed 1/16 in (2 mm for any length of weld, (B) In primary members, undercut shall be no more than 0.01 in [0.25 mm deep when the welds transverse to tensile stress under any design loading condition. Undercut shall x ‘be no more than 1/32in {1 mm] deep fr all other cases. (8) Porosity (A)CIP groove welds in but joins transverse to the direction of computed tensile stress shall have no visible piping porosity. For all other groove welds and fr fillet welds, the ‘sum of the visible piping porosity 1/32 in [1 mm or greater in diameter shall not exceed 5 in (10 mm] in any linear inch of weld and shall not exceed 3/4 in (20 mm] in any 12 in [300 mm length of weld {(B) The frequency of piping porosity in fillet welds shall not exceed one in each 4 in [100 ‘mm] of weld length and the maximum diameter shall not exceed 3/32 in [2.5 mi, Exception: for filet welds connecting stiffeners to web, the sum of the diameters of| x Piping porosity shall not exceed 3/8 in [10 mm] in any linear inch of weld and shall not exceed 34 in [20 mm] in any 12 in [300.mmn] length of weld (©) COP groove welds in but joints transverse othe direction of computed tensile stress shall have no piping porosity. For all other groove weld, the frequency of piping porosity shall not exceed one in 4 in [100 mm] of length and the maximum diameter shall not exceed 332 in [2.5 ma [Note:An“X" indieatesappiabity fo the connection typ a shaded area ndiates aon-appibly 230

También podría gustarte