R410A 60Hz

6CVP0-01A
 1. Model Names

Power Supply 8HP 10HP 12HP 14HP 16HP 18HP 20HP 22HP 24HP

3Ø, 460V, 60Hz 80DT2 100DT2 120DT2 140DT2 160DT2 180DT2 200DT2 220DT2 240DT2

3Ø, 220V , 60Hz 80BT2 100BT2 120BT2 - 160BT2 180BT2 200BT2 220BT2 240BT2

Power Supply 26HP 28HP 30HP 32HP 34HP 36HP

3Ø, 460V, 60Hz 260DT2 280DT2 300DT2 320DT2 - -

3Ø, 220V , 60Hz 260BT2 280BT2 300BT2 320BT2 340BT2 360BT2

Cooling Only ARUV

Heat Pump ARUN

General information 1
2.2 Outdoor Units(220V)

ARUV80BT2
ARUV100BT2
ARUV120BT2

ARUN80BT2
ARUN100BT2
ARUN120BT2

ARUV160BT2
ARUV180BT2
ARUV200BT2
ARUV220BT2
ARUV240BT2

ARUN160BT2
ARUN180BT2
ARUN200BT2
ARUN220BT2
ARUN240BT2

ARUV260BT2
ARUV280BT2
ARUV300BT2
ARUV320BT2
ARUV340BT2
ARUV360BT2

ARUN260BT2
ARUN280BT2
ARUN300BT2
ARUN320BT2
ARUN340BT2
ARUN360BT2

General information 3
 4. Nomenclature

4.1 Outdoor Unit

ARU N 100 D T 2

Serial Number
Air Discharge Type
S:Side Discharge
T:Top Discharge
Electrical Ratings
8: 3Ø, 380 ~ 415V, 50Hz 9: 3Ø, 380V, 60Hz
A: 3Ø, 220V, 50Hz B: 3Ø, 220V, 60Hz
L: 3Ø, 380 ~ 415V, 50Hz / 3Ø, 380V, 60Hz
D: 3Ø, 460V, 60Hz
Total Cooling Capacity in Horse Power(HP) unit
EX) 10HP➞'100'
Combination of Inverter Type and
Cooling Only or Heat Pump
N: Inverter and H/P V: Inverter and C/O
B: Inverter and Heat Recovery

System with
Outdoor Unit using R410A

General information 5
 Power Supply: Outdoor Unit (3Ø, 220V, 60Hz)
■ Cooling Only

Unit 1 Outdoor Unit 2 Outdoor Units

System(HP) 8 10 12 16
Model ARUV80BT2 ARUV100BT2 ARUV120BT2 ARUV160BT2
ARUV80BT2 ARUV100BT2 ARUV120BT2 ARUV80BT2
ARUV80BT2
Product Charge kg(lbs) 8(17.6) 8(17.6) 8(17.6) 8+8(17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) -2(-4.4)
Max. Connectable No. of Indoor Units 13 16 19 26
Net Weight kg 285 285 285 285+285
lbs 628 628 628 628+628
Dimensions mm 1,280x1,607x730 1,280x1,607x730 1,280x1,607x730 (1,280x1,607x730)x2
(WxHxD) inch 50.4x63.3x28.7 50.4x63.3x28.7 50.4x63.3x28.7 (50.4x63.3x28.7)x2
Connecting Pipes Liquid Pipes[mm(inch)] 9.52(3/8) 9.52(3/8) 12.7(1/2) 12.7(1/2)
Gas Pipes[mm(inch)] 19.05(3/4) 22.2(7/8) 28.58(1 1/8) 28.58(1 1/8)

Unit 2 Outdoor Unit 3 Outdoor Unit

System(HP) 18 20 22 24 26
Model ARUV180BT2 ARUV200BT2 ARUV220BT2 ARUV240BT2 ARUV260BT2
ARUV100BT2 ARUV100BT2 ARUV120BT2 ARUV120BT2 ARUV100BT2
ARUV80BT2 ARUV100BT2 ARUV100BT2 ARUV120BT2 ARUV80BT2
ARUV80BT2
Product Charge kg(lbs) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8+8(17.6+17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) 2(4.4) -2(-4.4)
Max. Connectable No. of Indoor Units 29 32 35 39 42
Net Weight kg 285+285 285+285 285+285 285+285 285+285+285
lbs 628+628 628+628 628+628 628+628 628+628+628
Dimensions mm (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x3
(WxHxD) inch (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x3
Connecting Pipes Liquid Pipes[mm(inch)] 15.88(5/8) 15.88(5/8) 15.88(5/8) 15.88(5/8) 19.05(3/4)
Gas Pipes[mm(inch)] 28.58(1 1/8) 28.58(1 1/8) 28.58(1 1/8) 34.9(1 3/8) 34.9(1 3/8)

Unit 3 Outdoor Unit

System(HP) 28 30 32 34 36
Model ARUV280BT2 ARUV300BT2 ARUV320BT2 ARUV340BT2 ARUV360BT2
ARUV100BT2 ARUV100BT2 ARUV120BT2 ARUV120BT2 ARUV120BT2
ARUV100BT2 ARUV100BT2 ARUV100BT2 ARUV120BT2 ARUV120BT2
ARUV80BT2 ARUV100BT2 ARUV100BT2 ARUV100BT2 ARUV120BT2
Product Charge kg(lbs) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) 2(4.4) 3(6.6)
Max. Connectable No. of Indoor Units 45 49 52 55 58
Net Weight kg 285+285+285 285+285+285 285+285+285 285+285+285 285+285+285
lbs 628+628+628 628+628+628 628+628+628 628+628+628 628+628+628
Dimensions mm (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3
(WxHxD) inch (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3
Connecting Pipes Liquid Pipes[mm(inch)] 19.05(3/4) 19.05(3/4) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Gas Pipes[mm(inch)] 34.9(1 3/8) 34.9(1 3/8) 34.9(1 3/8) 34.9(1 3/8) 41.3(1 5/8)

8 Outdoor Unit
 Power Supply: Outdoor Unit (3Ø, 220V, 60Hz)
■ Heat pump

Unit 1 Outdoor Unit 2 Outdoor Units

System(HP) 8 10 12 16
Model ARUN80BT2 ARUN100BT2 ARUN120BT2 ARUN160BT2
ARUN80BT2 ARUN100BT2 ARUN120BT2 ARUN80BT2
ARUN80BT2
Product Charge kg(lbs) 8(17.6) 8(17.6) 8(17.6) 8+8(17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) -2(-4.4)
Max. Connectable No. of Indoor Units 13 16 19 26
Net Weight kg 285 285 285 285+285
lbs 628 628 628 628+628
Dimensions mm 1,280x1,607x730 1,280x1,607x730 1,280x1,607x730 (1,280x1,607x730)x2
(WxHxD) inch 50.4x63.3x28.7 50.4x63.3x28.7 50.4x63.3x28.7 (50.4x63.3x28.7)x2
Connecting Pipes Liquid Pipes[mm(inch)] 9.52(3/8) 9.52(3/8) 12.7(1/2) 12.7(1/2)
Gas Pipes[mm(inch)] 19.05(3/4) 22.2(7/8) 28.58(1 1/8) 28.58(1 1/8)

Unit 2 Outdoor Unit 3 Outdoor Unit

System(HP) 18 20 22 24 26
Model ARUN180BT2 ARUN200BT2 ARUN220BT2 ARUN240BT2 ARUN260BT2
ARUN100BT2 ARUN100BT2 ARUN120BT2 ARUN120BT2 ARUN100BT2
ARUN80BT2 ARUN100BT2 ARUN100BT2 ARUN120BT2 ARUN80BT2
ARUN80BT2
Product Charge kg(lbs) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8+8(17.6+17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) 2(4.4) -2(-4.4)
Max. Connectable No. of Indoor Units 29 32 35 39 42
Net Weight kg 285+285 285+285 285+285 285+285 285+285+285
lbs 628+628 628+628 628+628 628+628 628+628+628
Dimensions mm (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x2 (1,280x1,607x730)x3
(WxHxD) inch (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x2 (50.4x63.3x28.7)x3
Connecting Pipes Liquid Pipes[mm(inch)] 15.88(5/8) 15.88(5/8) 15.88(5/8) 15.88(5/8) 19.05(3/4)
Gas Pipes[mm(inch)] 28.58(1 1/8) 28.58(1 1/8) 28.58(1 1/8) 34.9(1 3/8) 34.9(1 3/8)

Unit 3 Outdoor Unit

System(HP) 28 30 32 34 36
Model ARUN280BT2 ARUN300BT2 ARUN320BT2 ARUN340BT2 ARUN360BT2
ARUN100BT2 ARUN100BT2 ARUN120BT2 ARUN120BT2 ARUN120BT2
ARUN100BT2 ARUN100BT2 ARUN100BT2 ARUN120BT2 ARUN120BT2
ARUN80BT2 ARUN100BT2 ARUN100BT2 ARUN100BT2 ARUN120BT2
Product Charge kg(lbs) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6)
CF(Correction Factor) kg(lbs) -1(-2.2) 0(0) 1(2.2) 2(4.4) 3(6.6)
Max. Connectable No. of Indoor Units 45 49 52 55 58
Net Weight kg 285+285+285 285+285+285 285+285+285 285+285+285 285+285+285
lbs 628+628+628 628+628+628 628+628+628 628+628+628 628+628+628
Dimensions mm (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3 (1,280x1,607x730)x3
(WxHxD) inch (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3 (50.4x63.3x28.7)x3
Connecting Pipes Liquid Pipes[mm(inch)] 19.05(3/4) 19.05(3/4) 19.05(3/4) 19.05(3/4) 19.05(3/4)
Gas Pipes[mm(inch)] 34.9(1 3/8) 34.9(1 3/8) 34.9(1 3/8) 34.9(1 3/8) 41.3(1 5/8)

General information 9
3.1.2 ARUV100DT2, ARUV120DT2, ARUV140DT2, ARUV160DT2,ARUV80BT2, ARUV100BT2,
ARUV120BT2

Cooling Operation

Ind oor HEX EEV Ind oor HEX EEV

Fan Fan
Fil ter Fil ter

Ind oor Unit Ind oor Unit

High Temp. High Pressure Gas

High Temp. High Pressure Liquid
DC Fan DC Fan Low Temp. Low Pressure Gas
Outdoor
Temperature
Sensor

High Temp.
Sensor
Gas Pipe

Hot Gas
Valve
Low Temp.
s

Sensor Liquid Pipe

Suction
Temp.
Oil Sensor Oil
Separator Separator

Discharge Discharge
Temp. Temp.
Sensor(I) Sensor(C)
Con stant
Inverter
Acc umulator Speed
Comp
Comp
Sub-Cooling
Outlet Temp.
Sensor
Liquid Injection
s

Liquid Pipe Temp. Sensor

Sub-Cooler

Sub-Cooling
Inlet Temp.
Sensor
Sub-Coo ling EEV
Outdoo r Uni t

Press ure Sensor Temperature Sensor Check Valve Soleno id Valve

s

Remarks
Press ure Switch SVC Valve Strainer
EEV

23 Outdoor Unit
 Heating Operation

Ind oor HEX EEV Ind oor HEX EEV

Fan Fan
Fil ter Fil ter

Ind oor Unit Ind oor Unit

High Temp. High Press ure Gas

High Temp. High Press ure Liqu id
DC Fan DC Fan Low Temp. Low Press ure Gas

Outdoor
Temperature
Sensor

Outdoor Unit
HEX Temperature
Sensor

High Press ure

Sensor
Gas Pipe
4-Way Valve

Hot Gas
Valve
Low
s

Press ure Liquid Pipe

Suction Sensor
Outdoor Temperature
EEV Oil Sensor Oil
Separator Separator

Comp Comp
Disc harge Disc harge
Temperature Temperature
Sensor Con stant Sensor
Inverter
Acc umulator Speed
Comp
Comp
Sub-cooli ng Circuit
Outlet Temperature
Sensor
Liquid Injection
s

Liquid Pipe Temp. Sensor

Sub-Cooler

Sub-cooli ng Circuit
Inlet Temperature
Sensor

Sub-Coo ling EEV

Outdoo r Uni t

Press ure Sensor Temperature Sensor Check Valve Soleno id Valve

s

Remarks
Press ure Switch SVC Valve Strainer
EEV

Outdoor Unit 28
4.3 Cooling Only(3Ø, 220V)
4.3.1 ARUV80BT2, ARUV100BT2, ARUV120BT2

Outdoor Unit 34
4.4 Heat Pump(3Ø, 220V)
4.4.1 ARUN80BT2, ARUN100BT2, ARUN120BT2

35 Outdoor Unit
 ■ 1 Outdoor Unit - 3Ø, 220V

3 Phase 3 Wires Power line(R, S, T)

Transmission line (3 line): Wired remote control

Power supply switch Single Phase of power supply line(L, N)

(Switch fuse : ELCB) Transmission line (2 shield line): Between Indoor Unit and Outdoor Unit
3 Phase 3 Wires
Power supply
60Hz 220V
(Main Switch)
Power supply switch
(Switch fuse)

Power supply
1 Phase 60Hz
220V

WARNING
• Indoor Unit ground Lines are required for preventing electrical shock accident during current leakage,
Transmission disorder by noise effect and motor current leakage (without connection to pipe).
• Don't install an individual switch or electrical outlet to disconnect each of indoor unit separately from the power supply.
• Install the main switch that can interrupt all the power sources in an integrated manner because this system consists of the
equipment utilizing the multiple power sources.
• If there exists the possibility of reversed phase, lose phase, momentary blackout or the power goes on and off while the prod-
uct is operating, attach a reversed phase protection circuit locally.
Running the product in reversed phase may break the compressor and other parts.

Between Indoor and Master Outdoor unit

SODU IDU INTERNET DRY1 DRY2 GND 12V Master
B A B A Outdoor unit

3(A) 4(B) 3(A) 4(B) 3(A) 4(B)

The GND terminal is a '–' terminal for the central controller, not Ground Line

Outdoor Unit 38
 ■ 2 Outdoor Units - 3Ø, 220V

3 Phase 3 Wires Power line(R, S, T)

■ When the power source is connected Master
In series between the units. Transmission line (3 line): Wired remote control
Slave
Single Phase of power supply line(L, N)
Transmission line (2 shield line):
Power supply switch
(Switch fuse : ELCB) Between Outdoor Unit and Outdoor Unit
3 Phase 3 Wires Transmission line (2 shield line):
Power supply Between Indoor Unit and Outdoor Unit
60Hz 220V
(Main Switch) Power supply switch
(Switch fuse)
Power supply
1 Phase 60Hz
220V

■ When the power source is supplied to

Each outdoor unit individually.

Power supply switch

(Switch fuse : ELCB)
3 Phase 3 Wires
Power supply
60Hz 220V
(Main Switch)
Power supply switch
(Switch fuse)
Power supply
1 Phase 60Hz
220V

WARNING
• Indoor Unit ground Lines are required for preventing electrical shock accident during current leakage,
Transmission disorder by noise effect and motor current leakage (without connection to pipe).
• Don't install an individual switch or electrical outlet to disconnect each of indoor unit separately from the power supply.
• Install the main switch that can interrupt all the power sources in an integrated manner because this system consists of
the equipment utilizing the multiple power sources.
• If there exists the possibility of reversed phase, lose phase, momentary blackout or the power goes on and off while the
product is operating, attach a reversed phase protection circuit locally.
Running the product in reversed phase may break the compressor and other parts.

Between Indoor and Master Outdoor unit

SODU IDU INTERNET DRY1 DRY2 GND 12V Master SODU IDU INTERNET DRY1 DRY2 GND 12V Master
B A B A Outdoor unit B A B A Outdoor unit

SODU IDU INTERNET DRY1 DRY2 GND 12V Slave

3(A) 4(B) 3(A) 4(B) 3(A) 4(B)
B A B A Outdoor unit

The GND terminal is a '–' terminal for the central controller, not Ground Line

39 Outdoor Unit
6.1.1 Heat Pump
■ 60Hz 460V
Unit Power Supply COMP OFM
Model
Hz Volts Voltage-range MCA MOP MSC RLA kW FLA
8HP 60 460 414~506 14.4 22.6 21.36 20.2 0.7 4.0

10HP 60 460 414~506 18 29.2 21.36/61 20.2/10.4 0.7 4.0

12HP 60 460 414~506 21.8 36 21.36/61 20.2/10.4 0.7 4.0

14HP 60 460 414~506 27.2 45.8 21.36/61 20.2/11.5 0.7 4.0

16HP 60 460 414~506 31.5 53.4 21.36/61 20.2/11.5 0.7 4.0

18HP 60 460 414~506 28.6 45.1 21.36/61 /21.36 20.2/10.4 /20.2 1.4 8.0

20HP 60 460 414~506 32.4 51.9 21.36/61 /21.36 20.2/10.4 /20.2 1.4 8.0

22HP 60 460 414~506 37.8 61.7 21.36/61 /21.36 20.2/11.5/20.2 1.4 8.0

24HP 60 460 414~506 42.1 69.3 21.36/61 /21.36 20.2/11.5/20.2 1.4 8.0

26HP 60 460 414~506 49.5 82.7 21.36/61 /21.36/61 20.2/11.5/20.2/10.4 1.4 8.0

28HP 60 460 414~506 53.3 89.5 21.36/61 /21.36/61 20.2/11.5/20.2/11.5 1.4 8.0

30HP 60 460 414~506 58.7 99.3 21.36/61 /21.36/61 20.2/11.5/20.2/11.5 1.4 8.0

32HP 60 460 414~506 62.9 106.8 21.36/61 /21.36/61 20.2/11.5/20.2/11.5 1.4 8.0

■ 60Hz 220V
Unit Power Supply COMP OFM
Model
Hz Volts Voltage-range MCA MOP MSC RLA kW FLA
8HP 60 220 198 ~242 31.1 52.8 19/125 19.2/18.7 0.7 4
10HP 60 220 198 ~242 36.2 61.9 19/125 19.2/18.7 0.7 4
12HP 60 220 198 ~242 44 76 19/125 19.2/18.7 0.7 4
16HP 60 220 198 ~242 62.2 105.6 19/125/19/125 19.2/18.7/19.2/18.7 1.4 8
18HP 60 220 198 ~242 67.3 114.7 19/125/19/125 19.2/18.7/19.2/18.7 1.4 8
20HP 60 220 198 ~242 72.4 123.8 19/125/19/125 19.2/18.7/19.2/18.7 1.4 8
22HP 60 220 198 ~242 80.2 137.9 19/125/19/125 19.2/18.7/19.2/18.7 1.4 8
24HP 60 220 198 ~242 88 152 19/125/19/125 19.2/18.7/19.2/18.7 1.4 8
26HP 60 220 198~242 112.1 192.2 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0
28HP 60 220 198 ~ 242 113.8 195.2 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0
30HP 60 220 198 ~ 242 118.1 203.0 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0
32HP 60 220 198 ~ 242 123.5 212.7 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0
34HP 60 220 198 ~ 242 128.9 222.4 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0
36HP 60 220 198 ~ 242 134.3 232.1 19/125/19/125/19/125 19.2/18.7/19.2/18.7/19.2/18.7 2.10 12.0

Outdoor Unit 42
Notes:
1. Voltage range (Example)
Voltage supplied to the unit terminals should be within the Selection of proper circuit breaker
minimum and maximum range
➀ 10HP- Rated running current : 11.23A(460V)
2. Maximum allowable voltage unbalance between phase
is 2 % ➁ MCA = (1.25 x Load1) + Load2
3. MCA / MOP = (1.25 x 11.23) + 4.0 = 18.0A
MCA = (1.25 x Load1) + Load2 ➂ MOP = (2.25 x Load1) + Load2
MOP = (2.25 x Load1) + Load2 = (2.25 x 11.23) + 4.0 =29.2A
- Load1 : Rated running current of largest motor
(Compressor or other motor) MCA : Minimum Circuit Amperes (A)
- Load2 : any other load rated 1.0A or more MOP : Maximum rating Over current Protective device
4. Select wire spec. based on the MCA MSC : Maximum Starting Current
RLA : Rated Load Amperes (A)
5. Select proper circuit breaker as given below OFM : Outdoor Fan Motor
MCA < Selected circuit breaker ≤ MOP kW : Fan Motor rated output (kW)
6. Recommended circuit breaker is ELCB (Earth Leakage FLA : Full Load Amperes (A)
Circuit Breaker)
7. MSC & RLA are measured as the compressor only test
condition.
8. MSC values
21.36/61 : MSC of (INV. Comp) / (Const. Comp.1)
9. RLA is measured during each individual compressor test
condition.
20.2/10.4 : RLA of (INV. Comp) / (Const. Comp.1)
10. OFM is measured as the outdoor unit test condition

43 Outdoor Unit
 3. Installation Space
3.1 Individual Installation
■ Basic space required
A space of at least 250mm is necessary at the back for inlet air. Taking servicing, etc. from the rear into
account, a space of about 700mm should be provided, the same as at the front.
C

A 700mm or more (Control box is open/close type)

B 250mm or more
C Top discharge (open in principle)
D E
D Front inlet (open in principle)
E Rear inlet (open in principle)

< Top view > < Side view >

Rear Side B Rear Side B Rear Side B

Control Box

Control Box

Control Box
Front Side Front Side Front Side
A A A

■ When inlet air enters from right and left sides of unit

A 700mm or more
(Control box is open/close type)
A B
B 250mm or more h
C 150mm from the wall Rear Side
B

C C

CAUTION H

Front Side
A

Wall height(H) must not exceed height of the

product. If the wall height is higher than the whole < Side view > < Top view >

height of product by (h), Add (h) to , .

Rear Side Rear Side
B B

C C C C

Front Side Front Side

A A

A 250mm or more
(350mm or more at the coastal area.)
B 150mm from the wall A
h

CAUTION Rear Side

A
H B B

Wall height(H) must not exceed height of

the product. If the wall height is higher Front Side

than the whole height of product by (h), < Side view > < Top view >

Add (h) to , .
Rear Side Rear Side
A A

B B B B

Front Side Front Side

Installation 2
■ When unit is surrounded by walls

A 700mm or more (Control box is of a open/close type)

B 250mm or more

Rear Side B Rear Side B Rear Side B

B B B B B B

Front Side A Front Side A Front Side A

■ When there is an obstruction above the unit

A
A

A 45° or more B B

B 200mm or more
C C
C 250mm or more

< Front view >

A

C
C

< Front view >

D Air guide
E Air outlet guide (Procured at the site) D 58
7.6
F 250mm or more )

F
E
372.5
390

.5
723
125

< Side view > < Air guide >

3 Installation
3.2 Collective/ Continuous Installation
Space required for collective installation and continuous installation:When installing several units, leave
space between each block as shown below considering passage for air and people.
A (Be opened)
B 900mm or more (control box is of a open/close type)
C 250mm or more
D 150mm or more
Front Side

Front Side
Rear Side

Rear Side
Rear Side Rear Side Rear Side Rear Side
Front Side

Front Side

Front Side
Rear Side

Rear Side

Rear Side
Front Side Front Side Front Side Front Side

❈ B = 1250mm or more
at the coastal area

Front Side

Front Side
Front Side
Rear Side

Rear Side
Rear Side
or strong wind area

Front Side

Front Side
Rear Side

Rear Side
Rear Side D Rear Side D Rear Side D Rear Side

Front Side Front Side Front Side Front Side

Front Side

Front Side

Front Side
Rear Side

Rear Side

Rear Side
Front Side

Front Side
Rear Side

Rear Side

Rear Side D Rear Side D Rear Side D Rear Side

Front Side Front Side Front Side Front Side

Installation 4
5.2 Foundation for Installation
• Fix the unit tightly with bolts as shown below so that unit will not fall down due to earthquake or gust.
• Use the H-beam support as a base support
• Noise and vibration may occur from the floor or wall since vibration is transferred through the installation
part depending on installation status. Thus, use anti-vibration materials (cushion pad) fully (The base pad
shall be more than 200mm.

Anti-vibration
Spring washer materials
Frame Nut Concrete Four bolt are
base required
H-Beam 3 thread ridges

75
75

200

200
100

Foundation bolt executing method

WARNING
• Be sure to install unit in a place strong enough to withstand its weight.
Any lack of strength may cause unit to fall down, resulting in a personal injury.
• Have installation work in order to protect against a strong wind and earthquake. Any installation
deficiency may cause unit to fall down, resulting in a personal injury.
• Especially take care for support strength of the floor surface, water drain processing (processing of
water flown out from the outdoor unit during operation) and paths of the pipe and wiring when mak-
ing a base support.
• Don't use a tube or pipe for water drain in the base pan and perform water drain processing by
using the drain path. Water drain may not be done due to freezing of a tube or pipe.

Rear view Side view

Water
Drain
Path

Installation 8
6.2 Connection of High/Low Pressure Common Pipe

Slave
Outdoor Unit Slave2
Outdoor
Unit
Slave1
Outdoor
Master Unit Master
Outdoor Unit Outdoor Unit

2 Outdoor Units 3 Outdoor Units

1. For the High/Low Pressure Common pipe, connect both Master outdoor unit and slave outdoor units to the pipe (field
supply) by using elbows (field supply)
2. For cutting the pipe, connect the High/Low Pressure Common pipe after removing burrs, dusts and foreign materials
within the pipe. Otherwise, the product may not operate due to sludge within the pipe.

When connecting the pipes from the front of

Knock out
the outdoor unit, remove part .
When connecting the pipes from the side of the Transmission Line Hole
outdoor unit, remove part (the whole "Knock Power Cable Hole
out" part). Pipe Hole

(Front) (Side)

WARNING
After installing the pipe, clog the pipe excavation inlet of the front panel and the side panel
(Wire may be damaged due to entry of rats, animals, etc).

Installation 10
 7. Refrigerant Piping System
7.1 Refrigerant Pipe Connection
7.1.1 Y Branch Method

1 Outdoor Units
Example : 5 Indoor Units connected
: Outdoor Unit
: 1st branch (Y branch)
: Indoor Units

L150m (200m : Conditional application)

100m
l 40m (90m : Conditional application)

15m

2 Outdoor Units Slave

Master
Example : 5 Indoor Units connected
: Outdoor Unit
: 1st branch (Y branch) 10m
or less
: Indoor Units
: Downward Indoor Unit
: Connection branch pipe L150m(200m: Conditional application)
between Outdoor units:
100m

l 40m(90m: Conditional application)

ARCNN20

15m

13 Installation
3 Outdoor Units Slave2
Slave1
Example : 5 Indoor Units Master
connected 10m
or less
: Outdoor Unit
: 1st branch (Y branch)
: Indoor Units
: Downward Indoor Unit
: Connection branch pipe L150m(200m: Conditional application)

H 100m
between Outdoor units: l 40m(90m: Conditional application)
ARCNN30
: Connection branch pipe
between Outdoor units:
ARCNN20
h 15m

Piping length from outdoor branch to outdoor unit ≤10m, equivalent length:max 13m (for 18HP or more)
Conditional Application
To satisfy below condition to make 40 m ~ 90 m(131 ft ~295 ft) of pipe length after first branch.
1) Diameter of pipes between first branch and the last branch should be increased by one step, except pipe diameter
B,C,D is same as Diameter A
Ø6.35(1/4 inch) → Ø 9.52(3/8 inch) → Ø 12.7(1/2 inch) → Ø 15.88(5/8 inch) → Ø 19.05(3/4 inch) → Ø 22.2(7/8 inch) →
Ø 25.4*(1* inch), Ø 28.58(1-1/8 inch) → Ø 31.8*(1-1/4* inch), Ø 34.9(1-3/8 inch) → Ø 38.1*(1-1/2* inch)
* : It is not necessary to size up.
If the increased pipe size is larger than main pipe size, then increase the main(liquid,gas) pipe size as much as the
increased pipe size.
2) While calculating whole refrigerant pipe length, pipe B,C,D length should be calculated twice.
A+Bx2+Cx2+Dx2+a+b+c+d+e ≤ 1,000 m
3) Length of pipe from each indoor unit to the closest branch (a,b,c,d,e) ≤ 40m
4) [Length of pipe from outdoor unit to the farthest indoor unit 5 (A+B+C+D+e)]
- [Length of pipe outdoor unit to the closest indoor unit 1 (A+a)] ≤ 40m

Installation 14
➲ Refrigerant pipe diameter from branch to branch (B,C,D)
Downward Indoor Unit total capacity Liquid pipe Gas pipe
[kW(Btu/h)] [mm(inch)] [mm(inch)]
<22.4(76,400) Ø9.52(3/8) Ø19.05(3/4)
< 33(112,600) Ø9.52(3/8) Ø22.2(7/8)
< 47(160,400) Ø12.7(1/2) Ø28.58(1-1/8)
< 71(242,300) Ø15.88(5/8) Ø28.58(1-1/8)
< 104(354,900) Ø19.05(3/4) Ø34.9(1-3/8)

➲ Total pipe length = A+B+C+D+a+b+c+d+e ≤ 1,000m

Longest pipe length Equivalent pipe length
L
A+B+C+D+e ≤ 150m(200m**) *A+B+C+D+e ≤ 175m (225m**)
Longest pipe length after 1st branch
l
B+C+D+e ≤ 40m(90m**)
Difference in height(Outdoor Unit ↔ Indoor Unit)
H
H ≤ 100m
Difference in height (Indoor Unit ↔ Indoor Unit)
h h ≤15m
Difference in height (Outdoor Unit ↔ Outdoor Unit)
h1 h1 ≤ 5m

• * : Assume equivalent piping length of Y branch to be 0.5m, that of header to be 1m, calculation
purpose.
• ** : To apply Conditional Application

Upward Outdoor Unit Liquid pipe Gas pipe Upward Outdoor Unit Liquid pipe Gas pipe
total capacity [HP] [mm(inch)] [mm(inch)] total capacity [HP] [mm(inch)] [mm(inch)]
8 Ø9.52(3/8) Ø19.05(3/4) 16(220V) Ø12.7(1/2) Ø28.58(1-1/8)
10 Ø9.52(3/8) Ø22.2(7/8) 18, 20, 22, 24 Ø15.88(5/8) Ø28.58(1-1/8)
12~16 Ø12.7(1/2) Ø28.58(1-1/8)
18~22 Ø15.88(5/8) Ø28.58(1-1/8)
24 Ø15.88(5/8) Ø34.9(1-3/8) Upward Outdoor Unit Liquid pipe Gas pipe
total capacity [HP] [mm(inch)] [mm(inch)]
26~34 Ø19.05(3/4) Ø34.9(1-3/8)
8 Ø9.52(3/8) Ø19.05(3/4)
36 Ø19.05(3/4) Ø41.3(1-5/8)
10 Ø9.52(3/8) Ø22.2(7/8)
12, 14, 16(460V) Ø12.7(1/2) Ø28.58(1-1/8)

15 Installation
7.1.2 Header Method

1 Outdoor Unit
Example : 6 Indoor Units connected
: Outdoor Unit
: 1st branch
: Indoor Units
: Sealed piping
L 150m

H 100m
40m

15m

2 Outdoor Units
Slave
Example : 6 Indoor Units connected Master

: Outdoor Unit
10m
: Header branch or less
: Indoor Units
: Sealing
: Connection branch pipe L 150m
between Outdoor units:
H 100m

40m
ARCNN20

15m

Installation 16
3 Outdoor Units Slave2
Slave1
Example : 6 Indoor Units connected Master
: Outdoor Unit
10m
: Header branch or less
: Indoor Units
: Sealing
: Connection branch pipe
L150m
between Outdoor units:

H 100m
ARCNN30 l 40m

: Connection branch pipe

between Outdoor units:
ARCNN20
h 15m

Branch pipe can not be used after header

➲ Total pipe length = A+a+b+c+d+e+f ≤ 1,000m

Longest pipe length * Equivalent pipe length
L WARNING
A+f ≤ 150m A+f ≤ 175m
Longest pipe length after 1st branch
l Pipe length after header branching
f ≤ 40m (a~f)
Difference in height(Outdoor Unit ↔ Indoor Unit) It is recommended that difference
H H ≤ 100m in length of the pipes connected to
Difference in height (Indoor Unit ↔ Indoor Unit) the Indoor Units is minimized.
h h ≤15m Performance difference between
Difference in height (Outdoor Unit ↔ Outdoor Unit) Indoor Units may occur.
h1 h1 ≤ 5m

• * : Assume equivalent piping length of Y branch to be 0.5m, that of header to be 1m, calculation purpose
• Indoor Unit should be installed at lower position than the header.
• Piping length from outdoor branch to outdoor unit ≤ 10m, equivalent length : max 13m
(for 18HP or more)

17 Installation
7.1.3 Combination of Y branch/header method

Example : 5 Indoor Units connected

: Outdoor Unit
: 1st branch (Y branch)
: Y branch
: Indoor Unit
: Header

H 100m
: Sealed piping
L 150m
40m

h 15m
Branch pipe can not be used after header

Example : 5 Indoor Units connected

Slave
: Outdoor Unit
: 1st branch Master

: Y branch
10m
: Indoor Unit or less
: Connection branch pipe
between Outdoor units:
ARCNN20
: Header
H 100m

: Sealed piping
L 150m
40m
h 15m

Branch pipe can not be used after header

Installation 18
3 Outdoor Units Slave2
Slave1
Example : 5 Indoor Units connected Master
: Outdoor Unit
: 1st branch(Y branch) 10m
: Y branch or less

: Indoor Unit
: Connection branch pipe
between Outdoor units:
ARCNN30

H 100m
: Connection branch pipe L 150m
between Outdoor units: L40m

h 15m
ARCNN20
: Header
: Sealing

Branch pipe can not be used after header

➲ Refrigerant pipe diameter from branch to branch (B,C)

Downward Indoor Unit total capacity Liquid pipe Gas pipe
[kW(Btu/h)] [mm(inch)] [mm(inch)]
<22.4(76,400) Ø9.52(3/8) Ø19.05(3/4)
< 33(112,600) Ø9.52(3/8) Ø22.2(7/8)
< 47(160,400) Ø12.7(1/2) Ø28.58(1-1/8)
< 71(242,300) Ø15.88(5/8) Ø28.58(1-1/8 )
< 104(354,900) Ø19.05(3/4) Ø34.9(1-3/8)
104(354,900) ≤ Ø19.05(3/4) Ø41.3(1-5/8)

➲ Total pipe length = A+B+C+a+b+c+d+e ≤ 1,000m

Longest pipe length * Equivalent pipe length
L
A+B+b ≤ 150m A+B+b ≤ 175m
Longest pipe length after 1st branch
l
B+b ≤ 40m
Difference in height(Outdoor Unit ↔ Indoor Unit)
H
H ≤ 100m
Difference in height (Indoor Unit ↔ Indoor Unit)
h h ≤ 15m
Difference in height (Outdoor Unit ↔ Outdoor Unit)
h1 h1 ≤ 5m

• * : Assume equivalent pipe length of Y branch to be 0.5m, that of header to be 1m, calculation purpose
• Indoor Unit should be installed at lower position than the header.

19 Installation
7.2 Connection between outdoor and outdoor unit
■ Example of Pipe Connection between Outdoor
7.2.1 Pipe Connection between Outdoors

h1 Differnce in height between outdoor units

Less than 5m( h1 ≤ 5m).
Longest Pipe Length between Outdoors
Less than 10m, after 1st branch.

Less than 10m

CAUTION
Apply oil trap between outdoor unit installed Higher level and outdoor unit installed lower level.
Oil may be accumulated in stopped outdoor unit.

2. In case pipe length between outdoors is less than 2m

Less than 2m

23 Installation
7.2.3 In case pipe length between outdoors is 2m or more.
When the piping length between Branch of Outdoor units or between Branch and outdoor units.
Is 2 m or more, prepare a oil trap 200 mm or more as shown below) on the gas pipe line location.
Less than 2 m from branch.

Oil Trap
200mm
or more
Less than 2m
2m or more

Oil Trap Oil Trap

Less than 2m Less than 2m

2m or more 2m or more

7.2.4 Example of wrong connection

Oil is accumulating in
outdoor units when
system stops

Oil is accumulating in lower level

outdoor units when system stops

Installation 24
7.3 The amount of Refrigerant
The calculation of the additional charge should take into account the length of pipe.
A Additional charge (kg(lb)) Ex 10HP
Outdoor Unit a : ø6.35(1/4), 10m
B Product Charge(kg(lb))
Indoor Unit b : ø6.35(1/4), 10m
= Total liquid pipe (m): Ø22.2mm(7/8inch) x 0.354(kg/m) A : ø9.52(3/8), 40m c : ø6.35(1/4), 10m
B : ø9.52(3/8), 20m d : ø6.35(1/4), 10m
+ Total liquid pipe (m): Ø19.05mm(3/4inch) x 0.266(kg/m)
C : ø9.52(3/8), 20m e : ø6.35(1/4), 10m
+ Total liquid pipe (m): Ø15.88mm(5/8inch) x 0.173(kg/m)
A
+ Total liquid pipe (m): Ø12.7mm(1/2inch) x 0.118(kg/m) C X

+ Total liquid pipe (m): Ø9.52mm(3/8inch) x 0.061(kg/m) c d e

B 3 B 4 B 5 B
+ Total liquid pipe (m): Ø6.35mm(1/4inch) x 0.022(kg/m)
b
CF(kg) a
+ (Correction Factor) 1 B 2 B

Total amount(kg) = A + B
CAUTION If a negative result is obtained from Additional Charge = A x 0.061 + B x 0.061 + C x 0.061
the calculation, no refrigerant needs + (a+b+c+d+e) x 0.022 + CF
to be added. = 40 x 0.061 + 20 x 0.061 + 20 x 0.061
+ (10 x 5) x 0.022 + (0) (CF)
= 5.98(kg)
• 460V
HP 8 10 12 14 16 18 20 22 24 26 28 30 32
8 8 8 8 8 8+8 8+8 8+8 8+8 8+8 8+8 8+8 8+8
Product Charge kg(lbs) (17.6) (17.6) (17.6) (17.6) (17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6) (17.6+17.6)
-1 0 1 2 3 -1 0 1 2 3 4 5 6
CF kg(lbs) (-2.2) (0) (2.2) (4.4) (6.6) (-2.2) (0) (2.2) (4.4) (6.6) (8.8) (11.0) (13.2)

• 220V
HP 8 10 12 16 18 20 22 24
Product Charge kg(lbs) 8(17.6) 8(17.6) 8(17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6) 8+8(17.6+17.6)
CF kg(lbs) -1(-2.2) 0(0) 1(2.2) -2(-4.4) -1(-2.2) 0(0) 1(2.2) 2(4.4)

HP 26 28 30 32 34 36
Product Charge kg(lbs) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6) 8+8+8(17.6+17.6+17.6)
CF kg(lbs) -2(-4.4) -1(-2.2) 0(0) 1(2.2) 2(4.4) 3(6.6)

25 Installation
7.4 Distribution Method
7.4.1 Line Distribution

7.4.2 Vertical Distribution

Ensure that the branch pipes are attached vertically.

7.4.3 The others

Header

27 Installation
7.5 Refrigerant pipe fitting
7.5.1 Caution
1. Use the following materials for refrigerant piping.
• Material: Seamless phosphorous deoxidized copper pipe
• Wall thickness : Comply with the relevant local and national regulations for the designed pressure 3.8MPa. We
recommend the following table as the minimum wall thickness.
Outer diameter 6.35 9.52 12.7 15.88 19.05 22.2 25.4 28.58 31.8 34.9 38.1 41.3
[mm(inch)] (1/4) (3/8) (1/2) (5/8) (3/4) (7/8) (1) (1-1/8) (1-1/4) (1-3/8) (1-1/2) (1-15/16)
Minimum thickness 0.8 0.8 0.8 0.99 0.99 0.99 0.99 0.99 1.1 1.21 1.35 1.43
[mm(inch)] (0.03) (0.03) (0.03) (3.25) (0.04) (0.04) (0.04) (0.04) (0.04) (0.05) (0.05) (0.06)

2. Commercially available piping often contains dust and other materials. Always blow it clean with a dry inert gas.
3. Use care to prevent dust, water or other contaminants from entering the piping during installation.
4. Reduce the number of bending portions as much as possible, and make bending radius as big as possible.
5. Always use the branch piping set shown below, which are sold separately.

Header
Y branch
4 branch 7 branch 10 branch
ARBLN01620 ARBLN03320 ARBL054 ARBL057 ARBL1010
ARBLN07120 ARBLN14520 ARBL104 ARBL107 ARBL2010
6. If the diameters of the branch piping of the designated refrigerant piping differs, use a pipe cutter to cut the
connecting section and then use an adapter for connecting different diameters to connect the piping.
7. Always observe the restrictions on the refrigerant piping (such as rated length, difference in height, and pip-
ing diameter).
Failure to do so can result in equipment failure or a decline in heating/cooling performance.
8. A second branch cannot be made after a header. (These are shown by .)

A A

A To Outdoor Unit
B Sealed Piping

9. The Multi V will stop due to an abnormality like excessive or insufficient refrigerant. At such a time, always
properly charge the unit. When servicing, always check the notes concerning both the piping length and the
amount of additional refrigerant.
10. Never use refrigerant to perform an air purge. Always evacuate using a vacuum pump.
11. Always insulate the piping properly. Insufficient insulation will result in a decline in heating/cooling perfor-
mance, drip of condensate and other such problems.
12. When connecting the refrigerant piping, make sure the service valves of the Outdoor Unit is completely
closed (the factory setting) and do not operate it until the refrigerant piping for the Outdoor and Indoor Units
has been connected, a refrigerant leakage test has been performed and the evacuation process has been
completed.
13. Always use a non-oxidizing brazing material for brazing the parts and do not use flux. If not, oxidized film
can cause clogging or damage to the compressor unit and flux can harm the copper piping or refrigerant oil.

Installation 28
8.2 DIP Switch Setting
8.2.1 Location of setting Switch
Main PCB
SW01B SW02B
(DIP S/W) (DIP S/W)

7 - Segment

SW02V
Auto addressing

Installation 38
■ Checking according to dip switch setting
1. You can check the setting values of the Master outdoor unit from the 7 segment LED.
The dip switch setting should be changed when the power is OFF.
2. It checks whether the input is properly performed without the bad contact of the dip switch or not

■ Checking the setting of the Master unit

The number is sequentially appeared at the 7 segment in 5 seconds after applying the power. This
number represents the setting condition.(For example, represents 3Ø 220V 20HP heat pump)
Master model code ➔ Slave1 model code ➔ total capacity ➔ 2 ➔ 25 ➔ 140

1 ~255 : Master model code

1 ~255 : Slave1 model code
1 ~255 : Slave2 model code
}
Refer to table code

8~36HP : HP number(sum of master capacity and slave capacity)

No display : cooling only 2 : heat pump
25 : Nomal
140 : 3Ø 220V 160 : 3Ø 460V

Example) 3Ø 220V 20HP heat pump

151 ➔ 151 ➔ 20 ➔ 2 ➔ 25 ➔ 140

CAUTION
Product may not properly operate if the relevant DIP switch is not properly setup.

Model Code
3Ø 220V 3Ø 460V
Model Code Unit (HP) Model Code Unit (HP)
150 8 171 8
151 10 172 10
152 12 173 12
174 14
175 16

39 Installation
 ENGINEERING PRODUCT DATA BOOK
R410A 50/60Hz

6CVP0-01A

P/No.: MFL55028401

Air Conditioner
20 Yeouido-dong, Yeongdeungpo-gu,
Yeouido P.O.Box 335 Seoul,
150-721, Korea.
http://www.lgeaircon.com

The air conditioners manufactured by LG

All rights reserved have received ISO9001 certificate for
Printed in Korea June/2008 quality assurance and ISO14001
The specifications, designs, and File No. : A8974 Certificate No. : certificate for environmental
information in this brochure are subject to Volume:1 E00626/1 management system.
change without notice.