Vigueta y Bovedilla

SMG INGENIERIA DE DISEO ESTRUCTURAL
MEMORIA DE CALCULO ESTRUCTURAL

NORTE 74 # 3809
COL. LA JOYA
DEL, GUSTAVO A MADERO
MEXICO DF.
CALLE MELCHOR MUZQUIZ #59, COL. MARTIN CARRERA C.P 07070 DEL GUSTAVO A. MADERO, MEX. D.F.
TEL. 27-34-09-27, [email protected]
Proyecto: NORTE 74 # 3809
Calculo: ING. SALVADOR MELCHOR CRUZ
Fecha: jueves, 08 de septiembre de 2011
Reviso:
DESCRIPCION DE LA ESTRUCTURA
SE TRATA DE UNA UNIDAD HABITACIONAL DE 1 EDIFICIOS DE 5 NIVELES,
CON 2 VIVIENDAS, CON UN TOTAL DE 9 VIVIENDAS, LA PLANTA BAJA ES DE
ESTACIONAMIENTO CON 5 CAJONES DE ESTACIONAMIENTO, EL PREDIO TIENE
UNA SUPERFICIE DE 180 m2, Y SE UBICA EN CALLE NORTE-74 #3809, COL. LA
JOYA, DELEGACION GUSTAVO A. MADERO, MEXICO, D.F.
SUPERESTRUCTURA:
EL EDIFICIO SE ESTRUCTURARA A BASE DE MUROS DE CARGA Y
COLUMNAS EN PLANTA BAJA, EN ENTREPISOS SERA A BASE DE MUROS DE
CARGA CON BLOCK TABIMAX DE 12x12x23cm, CON LAS SIGUIENTES
CARACTERISTICAS MECANICAS, RESISTENCIA A COMPRESION f*m= 60 Kg./cm2,
RESISTENCIA AL CORTANTE V*m= 5.00 Kg./cm2 Y UN PESO ESPECIFICO DE
1,783 Kg./m3, UNIDOS CON MORTERO TIPO I SEGN N.T.C.M. 2.2.,
DEPENDIENDO DEL ANALISIS ALGUNOS MUROS SERAN SUSTITUIDOS CON
MUROS DE CONCRETO, EL CONCRETO A UTILIZAR EN LA SUPERESTRUCTURA
SERA CON UN fc= 200 Kg./cm2.
EL SISTEMA DE ENTREPISO SE RESOLVERA POR MEDIO DE LOSA VIGUETA
Y BOVEDILLA DE 20cm DE ESPESOR, CUMPLIENDO CON LAS ESPECIFICACIONES
DEL REGLAMENT0 DE CONSTRUCCIONES DEL DISTRITO FEDERAL Y SUS NORMAS
TECNICAS COMPLEMENTARIAS
SUBESTRUCTURA:
DE ACUERDO AL ESTUDIO DE MECANICA DE SUELOS, LA CIMENTACION SE
RESOLVERA POR MEDIO DE UN CAJON SEMICOMPENSADO, DESPLANTADO A
UNA PROFUNDIDAD DE -2.30m, SOBRE EL NIVEL DE BANQUETA, EL CUAL
CONSTA DE UNA LOSA FONDO DE CONCRETO REFORZADO DE 20cm, DE
ESPESOR, RIGIDIZADA MEDIANTE UN SISTEMA DE CONTRATRABES
PERIMETRALES DE 20cm DE ESPESOR, ASI COMO DE CONTRATRABES
CENTRALES DE 70cm DE PERALTE, CON UN ENRASE DE BLOCK TABIMAX Y UN
REMATE DE DALA DE CERRAMIENTO , Y UNA LOSA TAPA DE VIGUETA Y
BOVEDILLA DE 20cm DE ESPESOR, DE ACUERDO CON EL ESTUDIO DE
MECANICA DE SUELOS EL PREDIO SE LOCALIZA EN UNA ZONA DENOMINADA
ZONA DE LAGO IIIc, CON UNA CAPACIDAD DE CARGA DE 16.61 Ton/m2, PARA LO
CUAL SE UTILIZAN LOS SIGUIENTES FACTORES SISMICOS Qx=2.00, Qy=2.00,
EL CONCRETO A UTILIZAR PARA LA CIMENTACION SERA DE fc=250 Kg/cm2
Reviso:
Reviso:
REVICION DE LAS CONDICIONES DE REGULARIDAD SEGN LAS NTC DEL DF-2004
1.- Su planta es sensiblemente simtrica con respecto a dos ejes ortogonales por lo que
toca a masas as como, a muros y otros elementos resistentes. Estos son, adems SI CUMPLE
sensiblemente paralelos a los ejes ortogonales principales del edificio.
2.- La relacin de su altura a la dimensin menor de su base no pasa de 2.50 SI CUMPLE

H= 12.50 m H/b= 1.26
b= 9.92 m
3.- La relacin de largo a ancho de la base no excede de 2.50 SI CUMPLE

L= 14.00 m L/A= 1.41
A= 9.92 m
4.- En planta no tiene entrantes ni salientes cuya dimensin exceda de 20 por ciento de
la dimensin de la planta medida paralelamente a la direccin que se considera del NO CUMPLE
entrante o saliente.
5.- En cada nivel tiene un sistema de techo o piso rgido y resistente. SI CUMPLE
6.-
No tiene aberturas en sus sistemas de techo o piso cuya dimensin exceda de 20%
de la dimensin en planta medida paralelamente a la abertura; las areas huecas no
SI CUMPLE
ocasionan asimetras significativas ni difieren en posicin de un piso a otro y el rea
total de aberturas no excede en ningn nivel de 20% del rea de la planta.
7.- El peso de cada nivel, incluyendo la carga viva que debe considerarse para diseo
ssmico, no es mayor que 110% del correspondiente al piso inmediato inferior ni,
SI CUMPLE
excepcin hecha del ultimo nivel de la construccin, es menor que 70% de dicho
peso.
8.- Ningun piso tiene un area, delimitada po los paos exteriores de sus elementos
resistentes verticales, mayor que 110% de la del piso inmediato inferior, ni menor
que 70% de esta, se exime de este ultimo requisito unicamiente al ultimo piso de la NO CUMPLE
construccion. Ademas, el area de ningun entrepiso excede en mas de 50% a la
menor de las pisos inferiores.
9.- Todas las columnas estn restringidas en todos los pisos en dos direcciones,
SI CUMPLE
sensiblemente ortogonales por diafragmas horizontales y por trabes o losas planas.
10.- Ni la rigidez ni la resistencia al corte de ningn entrepiso difiere en mas del 50% de la
del entrepiso inmediatamente inferior. El ultimo entrepiso queda excluido de este SI CUMPLE
requisito.
11.- En ningn entrepiso la excentricidad torsional, calculada estticamente se excede

del 10% de la dimensin en planta de ese entrepiso medida paralelamente a la SI CUMPLE
excentricidad mencionada.
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
6
t
:t *==E Proyecto: NORTE 74 # 3809 I
E g Calculo: ING. SALVADOR MELCHOR CRUZ +
i e
x ;B Fecha: jueves, 08 de septiembre de 2011 +
9 9 ?
*
Reviso: t
aEE
a2
: > :
=3
= o <
i z H
- E2>
ETE
5 EB
F 4
; ffiF
4 = q
'Fe#p P
E
H = b
n
E
r Pl
vYii
:E
= E Z
9 EE
,az.
$E
fi
!"AX
. o =

z > >
=,iQ
E 6 S
* R
@ Ft
< P >
9
qRe xn
6 0 0
s =eH
388
o < i
xa8
n = .
oi
I .- x
Fe
X > o
Y9
o
8 F B
r q z
g F
* r >
s= -!.i
9!
E >
t" ! s
E=
+3
e>
4Z
c 4
H'
E=X
E u
i,i s
e
F.r.
9
i
FEF
*F.r
FE
@ 9
9 A
> #
3E
i :
8 F
i
E
o
=
3
d E '\'
= >
3 *
. =
- 1
C'
a
z o 3
9
9 :
a
-, o
83
3#
; o
e
4
0
t-l
F
x n 3
= h
F
r-
-
e
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Reviso:
Ing. Salvador Melchor Cruz Sp.07/11

GENERALES
IDENTIFICACIN: NORTE 74 (2)
Entrepisos: 5
Grupos de constantes: 4
Muros: 54
Destino del EDIFICIO: Habitacin
Carga viva sostenida en entrepisos: 170 kg/m2
para anlisis ssmico: 90 kg/m2
Carga viva sostenida en azotea: 100 kg/m2
para anlisis ssmico: 70 kg/m2
fy acero: 4,200 kg/cm2
Edicin de reglamento: 2004
Reduce momentos de volteo: No
Factor MV direccin perpendicular: 0.3
ENTREPISOS
A L T U R A (m) C.MUERTA C.GEOMETRICO DIMENSION MAXIMA
NE Muros Entrepiso (kg/m2) x (m) y (m) x (m) y (m)
1 2.250 2.500 340 15.500 10.000
2 2.250 2.500 340 15.500 10.000
3 2.250 2.500 340 15.500 10.000
4 2.250 2.500 340 15.500 10.000
5 2.250 2.500 320 15.500 10.000
GRUPOS DE CONSTANTES
P.VOL. ESPESOR TIPO DE f*m v* TIPO DE
NG (kg/m3) (cm) MURO (kg/cm2) (kg/cm2) MAMPOSTERIA
1 1,783 12.0 Confinado 60.00 4.00 Barro
2 2,400 13.0 Concreto E=113,137 G=45,255
3 2,400 20.0 Concreto E=113,137 G=45,255
4 2,400 30.0 Concreto E=113,137 G=45,255
DATOS ANLISIS SISMICO

Reglamento: RDF.2004
Tipo de anlisis: Dinmico
Clculo de respuestas: Cortantes equivalentes
Grupo: B
Zona: IIIc
QX: 2
QY: 2
kQ: 0.8 (irregular)
ex.accidental: 0.1 B
c: 0.4
a0: 0.1
Ta: 1.25 seg
Tb: 4.2 seg
r: 2
MUROS
L' Lap LONG A.TRI ACERO DIST EXTREMO I EXTREMO J
MURO NG Ei Ej Msp S (m) (m) (m) (m2) (cm2) (cm) X (m) Y (m) x (m) y (m)
1 1 1 1 L 2.861 3.35 2.84 6.0 0.284 9.521 3.145 9.547
29/ 100%
2 1 1 1 L 2.861 3.33 4.26 6.0 3.145 9.547 6.006 9.574
30/ 100%
3 1 1 5 L 0.120 2.580 4.57 4.26 6.0 9.206 9.646 11.786 9.669
4 1 1 5 C 0.120 2.880 5.39 4.26 6.0 11.786 9.669 14.666 9.694
5 2 1 5 L 0.120 0.420 0.00 14.666 7.140 15.086 7.140
6 1 1 5 L 1.620 4.39 2.84 6.0 9.206 6.220 10.826 6.220
7 1 1 5 C 3.120 11.07 4.26 6.0 11.846 6.220 14.966 6.220
8 2 1 5 O 0.820 1.64 9.086 3.300 9.906 3.300
9 1 1 5 C 2.150 3.240 6.19 4.26 6.0 11.726 3.300 14.966 3.300
10 2 1 5 L 0.120 0.420 0.00 14.666 2.560 15.086 2.560
11 1 1 5 L 1.620 2.55 2.84 6.0 9.086 1.380 10.706 1.380
12 1 1 1 L 3.090 2.14 4.26 6.0 0.306 0.100 3.396 0.100
38/ 100%
13 1 1 1 L 2.610 1.72 2.84 6.0 3.396 0.100 6.006 0.100
39/ 100%
47/ 50%
14 1 1 5 L 0.120 2.640 1.72 4.26 6.0 9.086 0.060 11.726 0.060
15 1 1 5 C 0.120 2.820 0.00 4.26 6.0 11.846 0.060 14.666 0.060
16 3 1 1 O 1.281 9.98 0.406 4.940 0.406 6.221
41/ 100%
32/ 50%
31/ 100%
42/ 100%
34/ 50%
17 3 1 1 O 1.281 14.67 3.396 4.940 3.396 6.221
46/ 100%
44/ 100%
ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 1

Reviso:

MUROS
L' Lap LONG A.TRI ACERO DIST EXTREMO I EXTREMO J
MURO NG Ei Ej Msp S (m) (m) (m) (m2) (cm2) (cm) X (m) Y (m) x (m) y (m)
32/ 50%
34/ 50%
47/ 50%
18 3 1 1 O 1.790 11.76 5.906 4.360 5.906 6.150
48/ 100%
35/ 100%
33/ 100%
49/ 50%
19 2 1 5 L 1.920 5.67 9.146 4.360 9.146 6.280
20 1 1 5 L 0.120 2.529 0.88 7.62 6.0 9.146 7.180 9.146 9.709
21 1 1 5 L 3.940 5.12 7.62 6.0 10.766 1.320 10.766 5.260
22 1 1 5 T 2.340 5.39 7.62 6.0 11.786 0.000 11.786 2.340
23 1 1 5 L 2.020 1.35 5.06 6.0 11.786 4.260 11.786 6.280
24 1 1 5 T 0.600 0.00 2.84 6.0 12.756 3.360 12.756 3.960
25 1 1 5 L 0.120 1.000 2.68 2.84 6.0 14.726 0.000 14.726 1.000
26 1 1 5 T 0.800 0.120 1.480 0.00 5.06 6.0 15.026 2.620 15.026 4.100
27 1 1 5 T 0.800 0.120 1.480 0.00 5.06 6.0 15.026 5.600 15.026 7.080
28 2 1 5 L 0.120 0.434 0.00 14.726 9.320 14.726 9.754
29 1 2 5 C 0.120 2.902 5.39 2.84 6.0 0.404 9.562 3.306 9.589
30 1 2 5 C 0.120 2.580 4.57 2.84 6.0 3.306 9.589 5.886 9.612
31 2 2 5 L 0.120 0.419 0.00 -0.010 7.140 0.409 7.140
32 1 2 5 C 3.134 11.04 2.84 6.0 0.112 6.220 3.246 6.220
33 1 2 5 L 1.620 4.39 2.84 6.0 4.266 6.220 5.886 6.220
34 1 2 5 C 2.160 3.248 0.00 4.26 6.0 0.118 3.300 3.366 3.300
35 2 2 5 O 0.820 1.64 5.186 3.300 6.006 3.300
36 2 2 5 L 0.120 0.420 0.00 0.000 2.560 0.420 2.561
37 1 2 5 L 1.620 2.55 2.84 6.0 4.386 1.380 6.006 1.380
38 1 2 5 C 0.120 2.821 0.00 4.26 6.0 0.425 0.060 3.246 0.060
39 1 2 5 L 0.120 2.640 1.72 2.84 6.0 3.366 0.060 6.006 0.060
40 1 2 5 L 0.120 1.000 2.68 2.84 6.0 0.366 0.000 0.363 1.000
41 1 2 5 T 0.800 0.120 1.479 0.00 2.84 6.0 0.060 2.620 0.056 4.099
42 1 2 5 T 0.800 0.120 1.481 0.00 2.84 6.0 0.053 5.599 0.050 7.080
43 2 2 5 L 0.120 0.300 0.00 0.345 9.321 0.344 9.621
44 1 2 5 T 0.600 0.00 2.84 6.0 2.336 3.360 2.336 3.960
45 1 2 5 T 2.340 5.39 2.84 6.0 3.306 0.000 3.306 2.340
46 1 2 5 L 2.020 1.50 2.84 6.0 3.306 4.260 3.306 6.280
47 1 2 5 L 3.940 5.20 4.26 6.0 4.326 1.320 4.326 5.260
48 2 2 5 L 1.920 5.70 5.946 4.360 5.946 6.280
49 1 2 5 L 0.120 2.493 0.88 4.26 6.0 5.946 7.180 5.946 9.673
50 4 1 1 L 0.450 1.79 0.434 9.171 0.434 9.621
43/ 100%
51 4 1 1 L 0.450 1.89 5.856 9.224 5.856 9.674
49/ 50%
52 4 1 1 L 0.450 2.87 0.456 0.000 0.456 0.450
40/ 100%
36/ 100%
53 4 1 1 T 0.450 4.82 3.306 0.000 3.306 0.450
45/ 100%
54 4 1 1 L 0.450 2.70 5.856 0.000 5.856 0.450
37/ 100%
AJUSTE DE DATOS
ACERO DIST CARGA MUERTA CARGA VIVA CARGA Grupo de
MURO ENT (cm2) (cm) (kg/m2) (kg/m2) ADICIONAL (kg) Constantes
15 1 2
19 1 3
5 1,000
48 5 1,000
ANLISIS SSMICO DINMICO [RDF2004]

PESO TOTAL EN SISMO 418.48 T
CORTANTES BASALES
esttico total X: 104.62 T
Y: 104.62 T
aWt/Q' X: 57.23 T
Y: 59.04 T
mnimo X: 45.78 T [factor: 0.8]
Y: 47.23 T
Centro de masa
Nivel W (T) x (m) y (m)
5 65.45 7.759 4.908
4 87.96 7.723 4.826
3 87.96 7.723 4.826
2 87.96 7.723 4.826
1 89.15 7.674 4.786
Suma 418.48

Reviso:

Periodo (seg) Aceleracin espectral Coef.Participacin
Modo x y x y x y Q'x Q'y
1 0.153 0.171 0.137 0.141 6.125 6.157 1.000 1.000
2 0.054 0.061 0.113 0.115 1.959 1.903 1.000 1.000
3 0.035 0.038 0.108 0.109 -0.973 -0.912 1.000 1.000
4 0.027 0.030 0.107 0.107 -0.502 -0.463 1.000 1.000
5 0.024 0.026 0.106 0.106 -0.329 -0.285 1.000 1.000
Peso modal efectivo % de peso total
Modo x (T) y (T) x y
1 368.00 371.90 87.94 88.87
2 37.66 35.51 9.00 8.49
3 9.29 8.17 2.22 1.95
4 2.47 2.11 0.59 0.50
5 1.06 0.80 0.25 0.19
Suma 418.48 418.48 100.00 100.00
Cortantes basales Alturas efectivas Momentos de volteo
Modo Vx (T) Vy (T) Hx (m) Hy (m) Mx (T*m) My (T*m)
1 50.32 52.46 8.466 8.410 426.03 441.24
2 4.26 4.07 -2.827 -3.267 -12.04 -13.29
3 1.01 0.89 1.813 1.722 1.82 1.54
4 0.26 0.23 -2.673 -2.931 -0.70 -0.66
5 0.11 0.08 0.748 0.617 0.08 0.05
Comb 50.51 52.63 426.21 441.44
Momento de volteo Rigidez total C o r t a n t e Distorsin*Q' en C.Masa Desplaz. en C.Masa
Ent. x (T*m) y (T*m) x (T/m) y (T/m) x (T) y (T) Q'x:1 Q'y:1 x (cm) y (cm)
5 29.718 30.450 151419 123200 11.887 12.180 0.00003 0.00004 0.10 0.13
4 94.666 97.219 153984 129074 26.055 26.775 0.00007 0.00008 0.09 0.12
3 187.735 193.347 169263 140740 37.451 38.653 0.00009 0.00011 0.08 0.10
2 301.089 310.968 181295 149254 45.726 47.403 0.00010 0.00013 0.06 0.07
1 426.208 441.444 166669 126482 50.512 52.630 0.00012 0.00017 0.03 0.04
Cortante Pos.Cortante Centro de torsin Excent.Calculada (m) Dimensiones planta
Nivel x (T) y (T) x (m) y (m) x (m) y (m) SismoX SismoY x (m) y (m)
5 11.89 12.18 7.759 4.908 7.559 4.685 0.223 0.200 15.500 10.000
4 26.05 26.77 7.739 4.864 7.558 4.689 0.175 0.181 15.500 10.000
3 37.45 38.65 7.734 4.852 7.560 4.707 0.146 0.174 15.500 10.000
2 45.73 47.40 7.732 4.848 7.561 4.719 0.129 0.171 15.500 10.000
1 50.51 52.63 7.726 4.842 8.648 3.951 0.891 -0.922 15.500 10.000
Excentricidades [ 1.5e+0.1b ; e-0.1b ] M o m e n t o s T o r s i o n a n t e s [ V*e ]
Excent. de diseo (m) sismo direccin X sismo direccin Y sismo direccin X sismo direccin Y
Nivel SismoX SismoY e1 (m) e2 (m) e1 (m) e2 (m) m1 (T*m) m2 (T*m) m1 (T*m) m2 (T*m)
5 0.445 0.461 1.668 -0.555 2.242 -1.089 19.83 -6.59 27.30 -13.26
4 0.445 0.461 1.668 -0.555 2.242 -1.089 43.46 -14.45 60.02 -29.16
3 0.445 0.461 1.668 -0.555 2.242 -1.089 62.47 -20.77 86.64 -42.09
2 0.445 0.461 1.668 -0.555 2.242 -1.089 76.28 -25.36 106.26 -51.62
1 0.891 -0.922 2.336 -0.109 -2.933 0.628 118.01 -12.68 -154.37 33.05
Fuerzas ssmicas equivalentes

Posicin de fuerzas ssmicas
Fuerzas ssmicas sismo direc.X sismo direc.Y
Nivel x (T) y (T) Y1 (m) Y2 (m) X1 (m) X2 (m)
5 11.887 12.180 6.353 4.131 9.800 6.470
4 14.168 14.595 6.357 4.134 9.800 6.469
3 11.396 11.878 6.375 4.152 9.802 6.471
2 8.274 8.750 6.387 4.164 9.803 6.472
1 4.786 5.228 12.670 6.600 -41.208 24.845
Suma 50.512 52.630
REVISION POR CARGA VERTICAL

MURO ENT Pu (T) Fe Fr Pr (T) CBu (T/m)
1 1 26.86 0.700 0.600 92.29 9.39
2 1 23.74 0.700 0.600 92.29 8.30
3 1 24.43 0.600 0.600 71.33 9.47
2 19.43 0.600 0.600 71.33 7.53
3 14.43 0.600 0.600 71.33 5.59
4 9.43 0.600 0.600 71.33 3.65
5 4.43 0.600 0.600 71.33 1.72
4 1 28.27 0.600 0.600 79.63 9.82
2 22.48 0.600 0.600 79.63 7.80
3 16.69 0.600 0.600 79.63 5.79
4 10.90 0.600 0.600 79.63 3.78
5 5.11 0.600 0.600 79.63 1.77
5 1 2.06 4.91
2 1.65 3.93
3 1.24 2.95
4 0.83 1.97
5 0.41 0.98
6 1 20.58 0.700 0.600 52.25 12.70
2 16.35 0.700 0.600 52.25 10.09
3 12.13 0.700 0.600 52.25 7.49
Reviso:

4 7.90 0.700 0.600 52.25 4.88
5 3.67 0.700 0.600 52.25 2.27
7 1 48.64 0.700 0.600 100.64 15.59
2 38.63 0.700 0.600 100.64 12.38
3 28.63 0.700 0.600 100.64 9.17
4 18.62 0.700 0.600 100.64 5.97
5 8.61 0.700 0.600 100.64 2.76
8 1 9.68 11.80
2 7.70 9.39
3 5.72 6.98
4 3.75 4.57
5 1.77 2.16
9 1 32.24 0.900 0.600 134.37 9.95
2 25.63 0.900 0.600 134.37 7.91
3 19.03 0.900 0.600 134.37 5.87
4 12.43 0.900 0.600 134.37 3.84
5 5.82 0.900 0.600 134.37 1.80
10 1 2.06 4.91
2 1.65 3.93
3 1.24 2.95
4 0.83 1.97
5 0.41 0.98
11 1 14.24 0.700 0.600 52.25 8.79
2 11.33 0.700 0.600 52.25 6.99
3 8.42 0.700 0.600 52.25 5.20
4 5.50 0.700 0.600 52.25 3.40
5 2.59 0.700 0.600 52.25 1.60
12 1 11.22 0.700 0.600 99.67 3.63
13 1 27.21 0.700 0.600 84.19 10.42
14 1 14.82 0.600 0.600 72.99 5.61
2 11.81 0.600 0.600 72.99 4.47
3 8.81 0.600 0.600 72.99 3.34
4 5.80 0.600 0.600 72.99 2.20
5 2.79 0.600 0.600 72.99 1.06
15 1 10.37 3.68
2 7.60 0.600 0.600 77.97 2.70
3 5.70 0.600 0.600 77.97 2.02
4 3.80 0.600 0.600 77.97 1.35
5 1.90 0.600 0.600 77.97 0.67
16 1 42.36 33.07
17 1 59.65 46.57
18 1 64.23 35.88
19 1 31.38 16.34
2 24.43 12.72
3 18.49 9.63
4 12.56 6.54
5 6.62 3.45
20 1 11.55 0.600 0.600 69.92 4.57
2 9.22 0.600 0.600 69.92 3.65
3 6.89 0.600 0.600 69.92 2.72
4 4.55 0.600 0.600 69.92 1.80
5 2.22 0.600 0.600 69.92 0.88
21 1 30.91 0.700 0.600 127.09 7.85
2 24.60 0.700 0.600 127.09 6.24
3 18.29 0.700 0.600 127.09 4.64
4 11.98 0.700 0.600 127.09 3.04
5 5.67 0.700 0.600 127.09 1.44
22 1 26.45 0.700 0.600 75.48 11.30
2 21.02 0.700 0.600 75.48 8.98
3 15.60 0.700 0.600 75.48 6.67
4 10.17 0.700 0.600 75.48 4.35
5 4.75 0.700 0.600 75.48 2.03
23 1 11.46 0.700 0.600 65.16 5.67
2 9.13 0.700 0.600 65.16 4.52
3 6.81 0.700 0.600 65.16 3.37
4 4.48 0.700 0.600 65.16 2.22
5 2.16 0.700 0.600 65.16 1.07
24 1 2.02 0.700 0.600 19.35 3.37
2 1.62 0.700 0.600 19.35 2.70
3 1.21 0.700 0.600 19.35 2.02
4 0.81 0.700 0.600 19.35 1.35
5 0.40 0.700 0.600 19.35 0.67
25 1 12.60 0.600 0.600 27.65 12.60
2 10.01 0.600 0.600 27.65 10.01
3 7.42 0.600 0.600 27.65 7.42
4 4.84 0.600 0.600 27.65 4.84
5 2.25 0.600 0.600 27.65 2.25
26 1 4.99 0.900 0.600 61.38 3.37
2 3.99 0.900 0.600 61.38 2.70

Reviso:

3 2.99 0.900 0.600 61.38 2.02
4 1.99 0.900 0.600 61.38 1.35
5 1.00 0.900 0.600 61.38 0.67
27 1 4.99 0.900 0.600 61.38 3.37
2 3.99 0.900 0.600 61.38 2.70
3 2.99 0.900 0.600 61.38 2.02
4 1.99 0.900 0.600 61.38 1.35
5 1.00 0.900 0.600 61.38 0.67
28 1 2.13 4.91
2 1.71 3.93
3 1.28 2.95
4 0.85 1.97
5 0.43 0.98
29 2 22.54 0.600 0.600 80.24 7.77
3 16.73 0.600 0.600 80.24 5.77
4 10.93 0.600 0.600 80.24 3.77
5 5.13 0.600 0.600 80.24 1.77
30 2 19.43 0.600 0.600 71.33 7.53
3 14.43 0.600 0.600 71.33 5.59
4 9.43 0.600 0.600 71.33 3.65
5 4.43 0.600 0.600 71.33 1.72
31 2 1.65 3.93
3 1.24 2.95
4 0.82 1.97
5 0.41 0.98
32 2 38.59 0.700 0.600 101.09 12.31
3 28.59 0.700 0.600 101.09 9.12
4 18.60 0.700 0.600 101.09 5.93
5 8.60 0.700 0.600 101.09 2.75
33 2 16.35 0.700 0.600 52.25 10.09
3 12.13 0.700 0.600 52.25 7.49
4 7.90 0.700 0.600 52.25 4.88
5 3.67 0.700 0.600 52.25 2.27
34 2 8.76 0.900 0.600 134.70 2.70
3 6.57 0.900 0.600 134.70 2.02
4 4.38 0.900 0.600 134.70 1.35
5 2.19 0.900 0.600 134.70 0.67
35 2 7.70 9.39
3 5.72 6.98
4 3.75 4.57
5 1.77 2.16
36 2 1.65 3.93
3 1.24 2.95
4 0.83 1.97
5 0.41 0.98
37 2 11.33 0.700 0.600 52.25 6.99
3 8.42 0.700 0.600 52.25 5.20
4 5.50 0.700 0.600 52.25 3.40
5 2.59 0.700 0.600 52.25 1.60
38 2 7.61 0.600 0.600 78.00 2.70
3 5.70 0.600 0.600 78.00 2.02
4 3.80 0.600 0.600 78.00 1.35
5 1.90 0.600 0.600 78.00 0.67
39 2 11.81 0.600 0.600 72.99 4.47
3 8.81 0.600 0.600 72.99 3.34
4 5.80 0.600 0.600 72.99 2.20
5 2.79 0.600 0.600 72.99 1.06
40 2 10.01 0.600 0.600 27.65 10.01
3 7.42 0.600 0.600 27.65 7.42
4 4.84 0.600 0.600 27.65 4.84
5 2.25 0.600 0.600 27.65 2.25
41 2 3.99 0.900 0.600 61.34 2.70
3 2.99 0.900 0.600 61.34 2.02
4 1.99 0.900 0.600 61.34 1.35
5 1.00 0.900 0.600 61.34 0.67
42 2 3.99 0.900 0.600 61.42 2.70
3 2.99 0.900 0.600 61.42 2.02
4 2.00 0.900 0.600 61.42 1.35
5 1.00 0.900 0.600 61.42 0.67
43 2 1.18 3.93
3 0.88 2.95
4 0.59 1.97
5 0.29 0.98
44 2 1.62 0.700 0.600 19.35 2.70
3 1.21 0.700 0.600 19.35 2.02
4 0.81 0.700 0.600 19.35 1.35
5 0.40 0.700 0.600 19.35 0.67
45 2 21.02 0.700 0.600 75.48 8.98
3 15.60 0.700 0.600 75.48 6.67
4 10.17 0.700 0.600 75.48 4.35
Reviso:

5 4.75 0.700 0.600 75.48 2.03
46 2 9.54 0.700 0.600 65.16 4.72
3 7.11 0.700 0.600 65.16 3.52
4 4.68 0.700 0.600 65.16 2.31
5 2.24 0.700 0.600 65.16 1.11
47 2 24.82 0.700 0.600 127.09 6.30
3 18.45 0.700 0.600 127.09 4.68
4 12.08 0.700 0.600 127.09 3.07
5 5.71 0.700 0.600 127.09 1.45
48 2 24.51 12.77
3 18.55 9.66
4 12.60 6.56
5 6.64 3.46
49 2 9.12 0.600 0.600 68.93 3.66
3 6.81 0.600 0.600 68.93 2.73
4 4.51 0.600 0.600 68.93 1.81
5 2.20 0.600 0.600 68.93 0.88
50 1 3.48 7.73
51 1 6.93 15.40
52 1 14.73 32.74
53 1 25.49 56.63
54 1 14.28 31.73
REVISION POR CARGA LATERAL

MURO ENT Fr Pi (T) K (T/m) Vd (T) Vt (T) Vt' (T) Vu (T) distor*Q' Vr (T) Vs (T)
1 1 0.700 17.46 11,045 3.35 1.60 2.09 6.13 0.02445 8.47
2 1 0.700 15.46 11,045 3.35 1.61 2.10 6.15 0.02359 8.05
3 1 0.700 15.85 10,600 3.21 1.57 2.05 5.94 0.02514 7.66
2 0.700 12.65 10,181 2.57 0.81 1.13 4.09 0.01805 6.99
3 0.700 9.44 9,673 2.14 0.68 0.95 3.42 0.01585 6.32
4 0.700 6.23 9,044 1.53 0.50 0.69 2.46 0.01219 5.64
5 0.700 3.02 8,939 0.70 0.24 0.33 1.14 0.00574 4.97
4 1 0.700 18.31 14,470 4.39 2.15 2.82 8.12 0.02587 8.68
2 0.700 14.60 13,664 3.45 1.10 1.53 5.50 0.01856 7.90
3 0.700 10.90 12,667 2.80 0.90 1.25 4.48 0.01631 7.13
4 0.700 7.19 11,405 1.93 0.63 0.87 3.10 0.01254 6.35
5 0.700 3.49 11,191 0.88 0.30 0.41 1.43 0.00590 5.57
5 1 1.47 416 0.13 0.03 0.05 0.19 0.00018
2 1.18 379 0.10 0.01 0.02 0.13 0.00014
3 0.88 326 0.07 0.01 0.02 0.10 0.00012
4 0.59 242 0.04 0.01 0.01 0.06 0.00009
5 0.29 233 0.02 0.00 0.00 0.02 0.00004
6 1 0.700 13.16 4,165 1.26 0.25 0.32 1.76 0.00017 5.49
2 0.700 10.49 3,892 0.98 0.09 0.13 1.23 0.00013 4.93
3 0.700 7.83 3,552 0.79 0.08 0.11 0.98 0.00011 4.37
4 0.700 5.16 3,119 0.53 0.05 0.07 0.66 0.00008 3.81
5 0.700 2.49 3,045 0.24 0.03 0.03 0.30 0.00004 3.24
7 1 0.700 30.87 16,349 4.95 0.96 1.26 6.93 0.00017 11.72
2 0.700 24.61 15,546 3.92 0.38 0.53 4.90 0.00013 10.41
3 0.700 18.34 14,552 3.22 0.31 0.44 4.03 0.00011 9.09
4 0.700 12.08 13,292 2.25 0.23 0.31 2.82 0.00008 7.78
5 0.700 5.82 13,079 1.03 0.11 0.15 1.30 0.00004 6.46
8 1 6.34 1,619 0.49 0.00 0.04 0.55 0.00014
2 5.06 1,619 0.41 0.01 0.05 0.48 0.00012
3 3.78 1,619 0.36 0.01 0.05 0.42 0.00010
4 2.50 1,619 0.27 0.01 0.03 0.32 0.00008
5 1.22 1,619 0.13 0.00 0.02 0.15 0.00004
9 1 0.700 20.86 17,300 5.24 0.03 0.38 5.93 0.00014 9.82
2 0.700 16.64 16,500 4.16 0.13 0.53 4.89 0.00012 8.94
3 0.700 12.42 15,511 3.43 0.10 0.43 4.03 0.00010 8.05
4 0.700 8.20 14,258 2.41 0.07 0.30 2.83 0.00008 7.16
5 0.700 3.97 14,046 1.10 0.03 0.14 1.30 0.00004 6.28
10 1 1.47 416 0.13 0.00 0.02 0.15 0.00014
2 1.18 379 0.10 0.00 0.02 0.12 0.00012
3 0.88 326 0.07 0.00 0.01 0.09 0.00011
4 0.59 242 0.04 0.00 0.01 0.05 0.00008
5 0.29 233 0.02 0.00 0.00 0.02 0.00004
11 1 0.700 9.28 4,165 1.26 0.03 0.36 1.54 0.00015 4.67
2 0.700 7.40 3,892 0.98 0.07 0.29 1.25 0.00013 4.28
3 0.700 5.53 3,552 0.79 0.06 0.23 1.00 0.00011 3.88
4 0.700 3.65 3,119 0.53 0.04 0.16 0.67 0.00009 3.49
5 0.700 1.77 3,045 0.24 0.02 0.07 0.31 0.00004 3.09
12 1 0.700 7.84 12,839 3.89 0.14 1.68 4.99 0.00016 6.84
13 1 0.700 18.13 9,157 2.78 0.10 1.20 3.56 0.00016 8.19
14 1 0.700 9.98 11,052 3.35 0.12 1.46 4.30 0.00016 6.53
2 0.700 7.97 10,630 2.68 0.27 1.12 3.61 0.00014 6.11
3 0.700 5.96 10,117 2.24 0.22 0.93 3.01 0.00012 5.69
4 0.700 3.95 9,483 1.60 0.16 0.67 2.16 0.00009 5.27

Reviso:

5 0.700 1.94 9,377 0.74 0.08 0.32 1.00 0.00004 4.84
15 1 7.41 42,034 12.74 0.46 5.56 16.35 0.00016
2 0.700 5.43 13,198 3.33 0.33 1.39 4.48 0.00014 5.88
3 0.700 4.07 12,203 2.70 0.27 1.12 3.64 0.00012 5.59
4 0.700 2.72 10,943 1.85 0.19 0.77 2.50 0.00009 5.31
5 0.700 1.36 10,729 0.84 0.09 0.37 1.15 0.00004 5.02
16 1 27.97 8,398 3.49 2.35 1.80 7.02 0.00033
17 1 38.84 8,398 3.49 1.50 1.15 5.87 0.00028
18 1 41.65 19,315 8.04 1.80 1.38 11.27 0.00023
19 1 20.43 27,711 11.53 0.10 0.36 12.91 0.00019
2 15.92 17,715 5.63 0.63 0.45 7.04 0.00016
3 12.13 16,486 4.53 0.52 0.37 5.67 0.00014
4 8.35 14,914 3.09 0.36 0.26 3.89 0.00010
5 4.56 14,777 1.46 0.17 0.13 1.84 0.00005
20 1 0.700 7.94 10,218 4.25 0.04 0.13 4.76 0.00019 5.92
2 0.700 6.35 9,803 3.11 0.35 0.25 3.89 0.00016 5.58
3 0.700 4.75 9,299 2.55 0.29 0.21 3.20 0.00014 5.25
4 0.700 3.16 8,674 1.80 0.21 0.15 2.26 0.00010 4.91
5 0.700 1.56 8,570 0.85 0.10 0.07 1.07 0.00005 4.58
21 1 0.700 20.29 21,520 8.95 0.33 1.18 10.61 0.00020 10.88
2 0.700 16.19 21,093 6.70 1.52 1.09 9.41 0.00018 10.02
3 0.700 12.09 20,589 5.65 1.30 0.94 7.97 0.00015 9.16
4 0.700 7.99 19,983 4.15 0.98 0.71 5.87 0.00012 8.30
5 0.700 3.89 19,884 1.97 0.47 0.34 2.79 0.00006 7.44
22 1 0.700 17.01 10,276 4.28 0.23 0.84 5.24 0.00020 7.50
2 0.700 13.56 9,895 3.14 0.94 0.68 4.72 0.00019 6.78
3 0.700 10.12 9,263 2.54 0.77 0.56 3.83 0.00017 6.06
4 0.700 6.67 8,286 1.72 0.53 0.39 2.61 0.00013 5.33
5 0.700 3.23 7,249 0.72 0.23 0.16 1.09 0.00006 4.61
23 1 0.700 7.71 6,620 2.75 0.15 0.54 3.37 0.00020 5.01
2 0.700 6.16 6,267 1.99 0.60 0.43 2.99 0.00019 4.69
3 0.700 4.60 5,834 1.60 0.49 0.35 2.41 0.00017 4.36
4 0.700 3.05 5,289 1.10 0.34 0.25 1.66 0.00013 4.03
5 0.700 1.50 5,197 0.51 0.16 0.12 0.78 0.00006 3.71
24 1 0.700 1.44 445 0.19 0.01 0.05 0.23 0.00021 1.31
2 0.700 1.16 422 0.13 0.05 0.04 0.21 0.00020 1.25
3 0.700 0.87 381 0.10 0.04 0.03 0.17 0.00018 1.19
4 0.700 0.58 304 0.06 0.02 0.02 0.10 0.00013 1.13
5 0.700 0.29 196 0.02 0.01 0.01 0.03 0.00006 1.07
25 1 0.700 8.06 1,345 0.56 0.06 0.21 0.75 0.00022 3.37
2 0.700 6.43 1,229 0.39 0.20 0.14 0.69 0.00023 3.03
3 0.700 4.79 1,080 0.30 0.15 0.11 0.53 0.00020 2.69
4 0.700 3.16 879 0.18 0.10 0.07 0.33 0.00015 2.34
5 0.700 1.53 844 0.08 0.04 0.03 0.15 0.00007 2.00
26 1 0.700 3.56 4,240 1.76 0.20 0.70 2.39 0.00023 3.23
2 0.700 2.85 4,027 1.28 0.68 0.49 2.31 0.00023 3.08
3 0.700 2.14 3,664 1.01 0.54 0.39 1.83 0.00020 2.94
4 0.700 1.42 3,078 0.64 0.35 0.25 1.17 0.00015 2.79
5 0.700 0.71 2,419 0.24 0.13 0.10 0.44 0.00007 2.64
27 1 0.700 3.56 4,240 1.76 0.20 0.70 2.39 0.00023 3.23
2 0.700 2.85 4,027 1.28 0.68 0.49 2.31 0.00023 3.08
3 0.700 2.14 3,664 1.01 0.54 0.39 1.83 0.00020 2.94
4 0.700 1.42 3,078 0.64 0.35 0.25 1.17 0.00015 2.79
5 0.700 0.71 2,419 0.24 0.13 0.10 0.44 0.00007 2.64
28 1 1.52 458 0.19 0.02 0.07 0.26 0.00022
2 1.22 417 0.13 0.07 0.05 0.24 0.00023
3 0.91 358 0.10 0.05 0.04 0.18 0.00020
4 0.61 266 0.06 0.03 0.02 0.10 0.00015
5 0.30 257 0.03 0.01 0.01 0.05 0.00007
29 2 0.700 14.64 13,835 3.49 1.09 1.52 5.53 0.01720 7.95
3 0.700 10.93 12,838 2.84 0.89 1.24 4.51 0.01511 7.17
4 0.700 7.21 11,576 1.96 0.63 0.86 3.13 0.01162 6.39
5 0.700 3.50 11,362 0.89 0.30 0.41 1.44 0.00547 5.61
30 2 0.700 12.65 11,372 2.87 0.90 1.25 4.56 0.01798 6.99
3 0.700 9.44 10,389 2.30 0.72 1.00 3.66 0.01580 6.32
4 0.700 6.23 9,149 1.55 0.50 0.69 2.48 0.01214 5.64
5 0.700 3.02 8,939 0.70 0.24 0.32 1.14 0.00572 4.97
31 2 1.18 376 0.09 0.01 0.02 0.13 0.00014
3 0.88 324 0.07 0.01 0.02 0.10 0.00012
4 0.59 240 0.04 0.01 0.01 0.05 0.00009
5 0.29 231 0.02 0.00 0.00 0.02 0.00004
32 2 0.700 24.58 15,657 3.95 0.38 0.53 4.94 0.00013 10.43
3 0.700 18.33 14,663 3.24 0.32 0.44 4.06 0.00011 9.11
4 0.700 12.07 13,404 2.27 0.23 0.31 2.85 0.00008 7.80
5 0.700 5.81 13,191 1.04 0.11 0.15 1.31 0.00004 6.49
33 2 0.700 10.49 3,892 0.98 0.09 0.13 1.23 0.00013 4.93
3 0.700 7.83 3,552 0.79 0.08 0.11 0.98 0.00011 4.37
4 0.700 5.16 3,119 0.53 0.05 0.07 0.66 0.00008 3.81
5 0.700 2.49 3,045 0.24 0.03 0.03 0.30 0.00004 3.24

Reviso:

34 2 0.700 6.25 16,564 4.18 0.13 0.53 4.91 0.00012 6.77
3 0.700 4.69 15,575 3.45 0.10 0.43 4.05 0.00010 6.44
4 0.700 3.13 14,323 2.42 0.07 0.30 2.85 0.00008 6.11
5 0.700 1.56 14,110 1.11 0.03 0.14 1.30 0.00004 5.79
35 2 5.06 1,619 0.41 0.01 0.05 0.48 0.00012
3 3.78 1,619 0.36 0.01 0.05 0.42 0.00010
4 2.50 1,619 0.27 0.01 0.03 0.32 0.00008
5 1.22 1,619 0.13 0.00 0.02 0.15 0.00004
36 2 1.18 379 0.10 0.00 0.02 0.12 0.05145
3 0.88 326 0.07 0.00 0.01 0.09 0.04512
4 0.59 242 0.04 0.00 0.01 0.05 0.03452
5 0.29 233 0.02 0.00 0.00 0.02 0.01608
37 2 0.700 7.40 3,892 0.98 0.07 0.29 1.25 0.00013 4.28
3 0.700 5.53 3,552 0.79 0.06 0.23 1.00 0.00011 3.88
4 0.700 3.65 3,119 0.53 0.04 0.16 0.67 0.00009 3.49
5 0.700 1.77 3,045 0.24 0.02 0.07 0.31 0.00004 3.09
38 2 0.700 5.43 13,206 3.33 0.33 1.39 4.49 0.00014 5.88
3 0.700 4.07 12,211 2.70 0.27 1.12 3.64 0.00012 5.59
4 0.700 2.72 10,951 1.85 0.19 0.77 2.50 0.00009 5.31
5 0.700 1.36 10,737 0.84 0.09 0.37 1.15 0.00004 5.02
39 2 0.700 7.97 10,630 2.68 0.27 1.12 3.61 0.00014 6.11
3 0.700 5.96 10,117 2.24 0.22 0.93 3.01 0.00012 5.69
4 0.700 3.95 9,483 1.60 0.16 0.67 2.16 0.00009 5.27
5 0.700 1.94 9,377 0.74 0.08 0.32 1.00 0.00004 4.84
40 2 0.700 6.43 1,229 0.39 0.10 0.14 0.58 0.06327 3.03
3 0.700 4.79 1,080 0.30 0.07 0.11 0.44 0.05493 2.69
4 0.700 3.16 879 0.18 0.05 0.07 0.28 0.04175 2.34
5 0.700 1.53 844 0.08 0.02 0.03 0.13 0.01999 2.00
41 2 0.700 2.85 4,021 1.28 0.33 0.49 1.93 0.07097 3.08
3 0.700 2.14 3,659 1.00 0.26 0.39 1.52 0.06162 2.93
4 0.700 1.42 3,073 0.64 0.17 0.25 0.97 0.04685 2.78
5 0.700 0.71 2,415 0.24 0.07 0.10 0.37 0.02243 2.63
42 2 0.700 2.85 4,033 1.28 0.33 0.49 1.94 0.09478 3.09
3 0.700 2.14 3,670 1.01 0.26 0.39 1.53 0.08229 2.94
4 0.700 1.43 3,083 0.64 0.17 0.26 0.98 0.06257 2.79
5 0.700 0.71 2,424 0.24 0.07 0.10 0.37 0.02996 2.64
43 2 0.84 141 0.04 0.01 0.02 0.07 0.05699
3 0.63 121 0.03 0.01 0.01 0.05 0.04947
4 0.42 89 0.02 0.00 0.01 0.03 0.00013
5 0.21 86 0.01 0.00 0.00 0.01 0.00006
44 2 0.700 1.16 422 0.13 0.02 0.04 0.19 0.00018 1.25
3 0.700 0.87 381 0.10 0.02 0.03 0.15 0.00015 1.19
4 0.700 0.58 304 0.06 0.01 0.02 0.09 0.00012 1.13
5 0.700 0.29 196 0.02 0.00 0.01 0.03 0.00006 1.07
45 2 0.700 13.56 9,895 3.14 0.46 0.68 4.19 0.00017 6.78
3 0.700 10.12 9,263 2.54 0.38 0.56 3.40 0.00015 6.06
4 0.700 6.67 8,286 1.72 0.26 0.39 2.31 0.00011 5.33
5 0.700 3.23 7,249 0.72 0.11 0.17 0.96 0.00005 4.61
46 2 0.700 6.41 6,267 1.99 0.29 0.43 2.65 0.00017 4.74
3 0.700 4.79 5,834 1.60 0.24 0.35 2.14 0.00015 4.40
4 0.700 3.17 5,289 1.10 0.17 0.25 1.47 0.00011 4.06
5 0.700 1.56 5,197 0.51 0.08 0.12 0.69 0.00005 3.72
47 2 0.700 16.32 21,093 6.70 0.75 1.10 8.56 0.00016 10.05
3 0.700 12.19 20,589 5.65 0.64 0.95 7.24 0.00014 9.18
4 0.700 8.06 19,983 4.15 0.48 0.71 5.32 0.00011 8.31
5 0.700 3.92 19,884 1.97 0.23 0.35 2.53 0.00005 7.44
48 2 15.97 17,715 5.63 0.31 0.46 6.69 0.00015
3 12.17 16,486 4.53 0.26 0.38 5.39 0.00013
4 8.37 14,914 3.09 0.18 0.27 3.69 0.00010
5 4.57 14,777 1.46 0.09 0.13 1.74 0.00005
49 2 0.700 6.28 9,538 3.03 0.17 0.25 3.60 0.00015 5.51
3 0.700 4.70 9,038 2.48 0.14 0.21 2.95 0.00013 5.18
4 0.700 3.12 8,417 1.75 0.10 0.15 2.08 0.00010 4.84
5 0.700 1.54 8,313 0.82 0.05 0.07 0.98 0.00005 4.51
50 1 2.34 659 0.27 0.18 0.14 0.55 0.00033
51 1 4.68 659 0.27 0.06 0.05 0.39 0.00023
52 1 9.57 659 0.27 0.18 0.14 0.55 0.00033
53 1 16.36 659 0.27 0.12 0.09 0.46 0.00028
54 1 9.29 659 0.27 0.06 0.05 0.39 0.00023
REVISION POR MOMENTO DE VOLTEO

MURO ENT Fr Pui (T) Mu (T*m) Mr (T*m) S1 (Kg/cm2)
1 1 0.800 19.21 40.72 42.30
2 1 0.800 17.00 40.72 53.52
3 1 0.800 17.44 39.08 48.40
2 0.800 13.91 24.36 45.73
3 0.800 10.38 15.45 43.06
4 0.800 6.85 8.00 40.40

Reviso:

5 0.800 3.33 2.52 37.73
4 1 0.800 20.14 53.35 56.54
2 0.800 16.06 32.69 53.10
3 0.800 11.99 20.23 49.65
4 0.800 7.91 10.09 46.20
5 0.800 3.84 3.16 42.75
5 1 1.62 1.54
2 1.30 0.91
3 0.97 0.52
4 0.65 0.21
5 0.32 0.07
6 1 0.800 14.48 15.36 21.09
2 0.800 11.54 9.31 19.72
3 0.800 8.61 5.67 18.34
4 0.800 5.68 2.76 16.97
5 0.800 2.74 0.86 15.60
7 1 0.600 33.95 60.28 62.62
2 0.800 27.07 37.20 67.79
3 0.800 20.18 23.24 61.46
4 0.800 13.29 11.76 55.14
5 0.800 6.40 3.69 48.82
8 1 6.97 5.97
2 5.56 3.87
3 4.15 2.58
4 2.75 1.43
5 1.34 0.46
9 1 0.800 22.95 63.78 66.55
2 0.800 18.30 39.48 62.12
3 0.800 13.66 24.77 57.69
4 0.800 9.01 12.61 53.26
5 0.800 4.37 3.96 48.83
10 1 1.62 1.54
2 1.30 0.91
3 0.97 0.52
4 0.65 0.21
5 0.32 0.07
11 1 0.800 10.21 15.36 19.09
2 0.800 8.14 9.31 18.12
3 0.800 6.08 5.67 17.16
4 0.800 4.02 2.76 16.19
5 0.800 1.95 0.86 15.23
12 1 0.800 8.62 47.34 50.35
13 1 0.800 19.94 33.76 39.02
14 1 0.800 10.98 40.75 44.57
2 0.800 8.77 25.44 42.86
3 0.800 6.56 16.16 41.15
4 0.800 4.35 8.39 39.44
5 0.800 2.14 2.65 37.72
15 1 8.15 154.98
2 0.800 5.97 31.58 43.59
3 0.800 4.48 19.49 42.36
4 0.800 2.99 9.68 41.12
5 0.800 1.49 3.03 39.88
16 1 30.77 42.09
17 1 42.72 41.58
18 1 45.81 95.63
19 1 22.47 137.20
2 17.51 52.39
3 13.34 32.17
4 9.18 15.97
5 5.02 5.19
20 1 0.800 8.74 50.59 68.15
2 0.800 6.98 28.99 66.85
3 0.800 5.23 18.15 65.55
4 0.800 3.47 9.29 64.25
5 0.800 1.72 3.01 62.95
21 1 0.800 22.32 106.55 123.78
2 0.800 17.81 62.38 118.53
3 0.800 13.30 40.18 113.28
4 0.800 8.79 21.39 108.04
5 0.800 4.28 6.99 102.79
22 1 0.800 18.71 50.88 69.63
2 0.800 14.92 29.26 67.04
3 0.800 11.13 18.08 64.45
4 0.800 7.34 8.87 61.86
5 0.800 3.55 2.55 59.27
23 1 0.800 8.48 32.78 37.29
2 0.800 6.77 18.54 36.29
3 0.800 5.07 11.38 35.28

Reviso:

4 0.800 3.36 5.66 34.28
5 0.800 1.65 1.83 33.27
24 1 0.800 1.59 2.21 4.84
2 0.800 1.27 1.25 4.79
3 0.800 0.95 0.74 4.73
4 0.800 0.64 0.33 4.68
5 0.800 0.32 0.07 4.63
25 1 0.800 8.87 6.66 10.90
2 0.800 7.07 3.63 10.39
3 0.800 5.27 2.11 9.88
4 0.800 3.48 0.94 9.38
5 0.800 1.68 0.30 8.87
26 1 0.800 3.92 20.99 24.79
2 0.800 3.13 11.91 24.46
3 0.800 2.35 7.15 24.12
4 0.800 1.57 3.30 23.79
5 0.800 0.78 0.85 23.46
27 1 0.800 3.92 20.99 24.79
2 0.800 3.13 11.91 24.46
3 0.800 2.35 7.15 24.12
4 0.800 1.57 3.30 23.79
5 0.800 0.78 0.85 23.46
28 1 1.68 2.27
2 1.34 1.23
3 1.01 0.70
4 0.67 0.28
5 0.34 0.09
29 2 0.800 16.11 33.10 40.28
3 0.800 12.02 20.50 36.80
4 0.800 7.94 10.24 33.31
5 0.800 3.85 3.21 29.83
30 2 0.800 13.91 27.21 33.99
3 0.800 10.38 16.59 31.32
4 0.800 6.85 8.09 28.66
5 0.800 3.33 2.52 25.99
31 2 1.29 0.90
3 0.97 0.52
4 0.65 0.21
5 0.32 0.07
32 2 0.800 27.04 37.46 53.70
3 0.800 20.16 23.42 47.35
4 0.800 13.28 11.86 41.01
5 0.800 6.40 3.72 34.66
33 2 0.800 11.54 9.31 19.72
3 0.800 8.61 5.67 18.34
4 0.800 5.68 2.76 16.97
5 0.800 2.74 0.86 15.60
34 2 0.800 6.88 39.63 51.35
3 0.800 5.16 24.87 49.71
4 0.800 3.44 12.67 48.06
5 0.800 1.72 3.98 46.42
35 2 5.56 3.87
3 4.15 2.58
4 2.75 1.43
5 1.34 0.46
36 2 1.30 0.91
3 0.97 0.52
4 0.65 0.21
5 0.32 0.07
37 2 0.800 8.14 9.31 18.12
3 0.800 6.08 5.67 17.16
4 0.800 4.02 2.76 16.19
5 0.800 1.95 0.86 15.23
38 2 0.800 5.98 31.60 43.61
3 0.800 4.48 19.50 42.37
4 0.800 2.99 9.69 41.14
5 0.800 1.49 3.03 39.90
39 2 0.800 8.77 25.44 30.84
3 0.800 6.56 16.16 29.12
4 0.800 4.35 8.39 27.41
5 0.800 2.14 2.65 25.70
40 2 0.800 7.07 3.63 10.39
3 0.800 5.27 2.11 9.88
4 0.800 3.48 0.94 9.38
5 0.800 1.68 0.30 8.87
41 2 0.800 3.13 11.89 14.30
3 0.800 2.35 7.14 13.97
4 0.800 1.57 3.29 13.63
5 0.800 0.78 0.85 13.30
42 2 0.800 3.14 11.93 14.32
Reviso:

3 0.800 2.35 7.16 13.99
4 0.800 1.57 3.30 13.66
5 0.800 0.78 0.85 13.32
43 2 0.93 0.42
3 0.69 0.24
4 0.46 0.10
5 0.23 0.03
44 2 0.800 1.27 1.25 4.79
3 0.800 0.95 0.74 4.73
4 0.800 0.64 0.33 4.68
5 0.800 0.32 0.07 4.63
45 2 0.800 14.92 29.26 31.39
3 0.800 11.13 18.08 28.80
4 0.800 7.34 8.87 26.20
5 0.800 3.55 2.55 23.61
46 2 0.800 7.05 18.54 22.28
3 0.800 5.27 11.38 21.23
4 0.800 3.49 5.66 20.18
5 0.800 1.71 1.83 19.14
47 2 0.800 17.96 62.38 75.58
3 0.800 13.41 40.18 70.29
4 0.800 8.86 21.39 64.99
5 0.800 4.32 6.99 59.70
48 2 17.56 52.39
3 13.39 32.17
4 9.21 15.97
5 5.03 5.19
49 2 0.800 6.91 28.21 39.01
3 0.800 5.17 17.64 37.74
4 0.800 3.43 9.01 36.47
5 0.800 1.70 2.92 35.21
50 1 2.58 3.30
51 1 5.15 3.26
52 1 10.53 3.29
53 1 18.00 3.26
54 1 10.22 3.26
OTROS
Pu Mu Vu
MURO ENT (T) (T) (T)
1 1 26.86 40.72 6.13
2 1 23.74 40.72 6.15
3 1 24.43 39.08 5.94
2 19.43 24.36 4.09
3 14.43 15.45 3.42
4 9.43 8.00 2.46
5 4.43 2.52 1.14
4 1 28.27 53.35 8.12
2 22.48 32.69 5.50
3 16.69 20.23 4.48
4 10.90 10.09 3.10
5 5.11 3.16 1.43
5 1 2.06 1.54 0.19
2 1.65 0.91 0.13
3 1.24 0.52 0.10
4 0.83 0.21 0.06
5 0.41 0.07 0.02
6 1 20.58 15.36 1.76
2 16.35 9.31 1.23
3 12.13 5.67 0.98
4 7.90 2.76 0.66
5 3.67 0.86 0.30
7 1 48.64 60.28 6.93
2 38.63 37.20 4.90
3 28.63 23.24 4.03
4 18.62 11.76 2.82
5 8.61 3.69 1.30
8 1 9.68 5.97 0.55
2 7.70 3.87 0.48
3 5.72 2.58 0.42
4 3.75 1.43 0.32
5 1.77 0.46 0.15
9 1 32.24 63.78 5.93
2 25.63 39.48 4.89
3 19.03 24.77 4.03
4 12.43 12.61 2.83
5 5.82 3.96 1.30
10 1 2.06 1.54 0.15

Reviso:

OTROS
Pu Mu Vu
2 1.65 0.91 0.12
3 1.24 0.52 0.09
4 0.83 0.21 0.05
5 0.41 0.07 0.02
11 1 14.24 15.36 1.54
2 11.33 9.31 1.25
3 8.42 5.67 1.00
4 5.50 2.76 0.67
5 2.59 0.86 0.31
12 1 11.22 47.34 4.99
13 1 27.21 33.76 3.56
14 1 14.82 40.75 4.30
2 11.81 25.44 3.61
3 8.81 16.16 3.01
4 5.80 8.39 2.16
5 2.79 2.65 1.00
15 1 10.37 154.98 16.35
2 7.60 31.58 4.48
3 5.70 19.49 3.64
4 3.80 9.68 2.50
5 1.90 3.03 1.15
16 1 42.36 42.09 7.02
17 1 59.65 41.58 5.87
18 1 64.23 95.63 11.27
19 1 31.38 137.20 12.91
2 24.43 52.39 7.04
3 18.49 32.17 5.67
4 12.56 15.97 3.89
5 6.62 5.19 1.84
20 1 11.55 50.59 4.76
2 9.22 28.99 3.89
3 6.89 18.15 3.20
4 4.55 9.29 2.26
5 2.22 3.01 1.07
21 1 30.91 106.55 10.61
2 24.60 62.38 9.41
3 18.29 40.18 7.97
4 11.98 21.39 5.87
5 5.67 6.99 2.79
22 1 26.45 50.88 5.24
2 21.02 29.26 4.72
3 15.60 18.08 3.83
4 10.17 8.87 2.61
5 4.75 2.55 1.09
23 1 11.46 32.78 3.37
2 9.13 18.54 2.99
3 6.81 11.38 2.41
4 4.48 5.66 1.66
5 2.16 1.83 0.78
24 1 2.02 2.21 0.23
2 1.62 1.25 0.21
3 1.21 0.74 0.17
4 0.81 0.33 0.10
5 0.40 0.07 0.03
25 1 12.60 6.66 0.75
2 10.01 3.63 0.69
3 7.42 2.11 0.53
4 4.84 0.94 0.33
5 2.25 0.30 0.15
26 1 4.99 20.99 2.39
2 3.99 11.91 2.31
3 2.99 7.15 1.83
4 1.99 3.30 1.17
5 1.00 0.85 0.44
27 1 4.99 20.99 2.39
2 3.99 11.91 2.31
3 2.99 7.15 1.83
4 1.99 3.30 1.17
5 1.00 0.85 0.44
28 1 2.13 2.27 0.26
2 1.71 1.23 0.24
3 1.28 0.70 0.18
4 0.85 0.28 0.10
5 0.43 0.09 0.05
29 2 22.54 33.10 5.53
3 16.73 20.50 4.51
4 10.93 10.24 3.13
5 5.13 3.21 1.44

Reviso:

OTROS
Pu Mu Vu
30 2 19.43 27.21 4.56
3 14.43 16.59 3.66
4 9.43 8.09 2.48
5 4.43 2.52 1.14
31 2 1.65 0.90 0.13
3 1.24 0.52 0.10
4 0.82 0.21 0.05
5 0.41 0.07 0.02
32 2 38.59 37.46 4.94
3 28.59 23.42 4.06
4 18.60 11.86 2.85
5 8.60 3.72 1.31
33 2 16.35 9.31 1.23
3 12.13 5.67 0.98
4 7.90 2.76 0.66
5 3.67 0.86 0.30
34 2 8.76 39.63 4.91
3 6.57 24.87 4.05
4 4.38 12.67 2.85
5 2.19 3.98 1.30
35 2 7.70 3.87 0.48
3 5.72 2.58 0.42
4 3.75 1.43 0.32
5 1.77 0.46 0.15
36 2 1.65 0.91 0.12
3 1.24 0.52 0.09
4 0.83 0.21 0.05
5 0.41 0.07 0.02
37 2 11.33 9.31 1.25
3 8.42 5.67 1.00
4 5.50 2.76 0.67
5 2.59 0.86 0.31
38 2 7.61 31.60 4.49
3 5.70 19.50 3.64
4 3.80 9.69 2.50
5 1.90 3.03 1.15
39 2 11.81 25.44 3.61
3 8.81 16.16 3.01
4 5.80 8.39 2.16
5 2.79 2.65 1.00
40 2 10.01 3.63 0.58
3 7.42 2.11 0.44
4 4.84 0.94 0.28
5 2.25 0.30 0.13
41 2 3.99 11.89 1.93
3 2.99 7.14 1.52
4 1.99 3.29 0.97
5 1.00 0.85 0.37
42 2 3.99 11.93 1.94
3 2.99 7.16 1.53
4 2.00 3.30 0.98
5 1.00 0.85 0.37
43 2 1.18 0.42 0.07
3 0.88 0.24 0.05
4 0.59 0.10 0.03
5 0.29 0.03 0.01
44 2 1.62 1.25 0.19
3 1.21 0.74 0.15
4 0.81 0.33 0.09
5 0.40 0.07 0.03
45 2 21.02 29.26 4.19
3 15.60 18.08 3.40
4 10.17 8.87 2.31
5 4.75 2.55 0.96
46 2 9.54 18.54 2.65
3 7.11 11.38 2.14
4 4.68 5.66 1.47
5 2.24 1.83 0.69
47 2 24.82 62.38 8.56
3 18.45 40.18 7.24
4 12.08 21.39 5.32
5 5.71 6.99 2.53
48 2 24.51 52.39 6.69
3 18.55 32.17 5.39
4 12.60 15.97 3.69
5 6.64 5.19 1.74
49 2 9.12 28.21 3.60
3 6.81 17.64 2.95
4 4.51 9.01 2.08
Reviso:

OTROS
Pu Mu Vu
5 2.20 2.92 0.98
50 1 3.48 3.30 0.55
51 1 6.93 3.26 0.39
52 1 14.73 3.29 0.55
53 1 25.49 3.26 0.46
54 1 14.28 3.26 0.39

Reviso:
1
Ag.30/11
NORTE 74 (2) -NORTE 74 (2 ANEM)-

Nivel 1
Ing. Salvador Melchor Cruz
V3.08
ANEMgcW
Reviso:
2
Ag.30/11

Nivel 2
V3.08
ANEMgcW
Reviso:
3
Ag.30/11

Nivel 3
V3.08
ANEMgcW
Reviso:
4
Ag.30/11

Nivel 4
V3.08
ANEMgcW
Reviso:
5
Ag.30/11

Nivel 5
V3.08
ANEMgcW
Reviso:
CALCULO DE CENTRO DE CARGAS EN PLANTA BAJA

COORDENA COORDENAD
MURO CARGA CARGA DAS AS MX MY
N MUROS REDUCIDA DX DY
(TON) (TON) m m Ton.m Ton.m
(CARGA/1.40)
1 26.86 19.19 1.71 9.53 32.89 182.92
2 23.74 16.96 4.58 9.56 77.59 162.12
3 24.43 17.45 10.50 9.66 183.16 168.52
4 28.27 20.19 13.22 9.68 267.01 195.50
5 1.42 1.01 14.87 7.14 15.09 7.24
6 20.58 14.70 10.02 6.22 147.24 91.43
7 48.64 34.74 13.41 6.22 465.76 216.10
8 9.68 6.91 9.50 3.30 65.66 22.82
9 32.24 23.03 13.35 3.30 307.34 75.99
10 1.42 1.01 14.88 2.56 15.09 2.60
11 14.24 10.17 9.90 1.38 100.66 14.04
12 11.22 8.01 1.85 0.10 14.83 0.80
13 27.21 19.44 4.70 0.10 91.37 1.94
14 14.82 10.59 10.41 0.06 110.15 0.64
15 10.37 7.41 13.26 0.06 98.19 0.44
16 41.84 29.89 0.41 5.58 12.13 166.78
17 59.65 42.61 3.40 5.58 144.69 237.77
18 64.23 45.88 5.91 5.26 270.96 241.09
19 31.38 22.41 9.15 5.32 205.00 119.24
20 11.55 8.25 9.15 8.44 75.45 69.67
21 30.91 22.08 10.77 3.29 237.70 72.64
22 26.45 18.89 11.79 1.17 222.67 22.10
23 11.46 8.19 11.79 5.27 96.48 43.14
24 2.02 1.44 12.76 3.66 18.41 5.28
25 12.60 9.00 14.73 0.50 132.53 4.50
26 4.99 3.56 15.03 3.36 53.56 11.98
27 4.99 3.56 15.03 6.34 53.56 22.60
28 1.46 1.04 14.73 9.54 15.36 9.95
50 3.11 2.22 0.43 9.40 0.96 20.87
51 6.93 4.95 5.86 9.45 28.99 46.77
52 14.21 10.15 0.46 0.23 4.63 2.28
53 25.49 18.21 3.31 0.23 60.19 4.10
54 14.28 10.20 5.86 0.23 59.73 2.30
SUMA 473.35 3685.02 2246.15
Reviso:
Reviso:
Reviso:
CALCULO DEL CENTRO DE CARGAS EN LA CIMENTACION
(CAJON DE CIMENTACION)
PESO PESO
A. TRIB A. TRIB A. TRIB LONG. PESO PESO PESO PESO
CONTRA CONTRA COORDE COORDEN
LOSA LOSA CISTER CONTRA LOSA LOSA DE MURO DE PESO Mx My
N TRABE TRABE NADAS ADAS
BASE TAPA NA TRABE BASE. TAPA. AGUA ENRASE TOTAL Ton/m Ton/m
(CT- (CT- Dx Dy
m2 m2 m2 m Ton Ton TON Ton
1)Ton 2)Ton
1 6.59 6.59 14.48 3.16 2.11 12.51 17.78 7.55 9.59 134.26 170.54
2 0.12 0.12 0.50 0.06 0.04 0.43 0.53 14.84 7.10 7.84 3.75
3 7.62 7.62 5.30 3.66 2.44 1.65 1.06 8.81 3.16 6.22 27.84 54.80
4 2.29 2.29 2.29 3.44 1.10 0.73 4.12 2.97 8.92 7.53 6.22 67.18 55.50
5 7.77 7.77 5.84 3.73 2.49 1.82 1.17 9.21 12.07 6.22 111.11 57.26
6 7.62 7.62 5.30 3.66 2.44 1.65 1.06 8.81 3.16 3.30 27.84 29.07
7 2.29 2.29 2.29 3.44 1.10 0.73 4.12 2.97 8.92 7.53 0.10 67.18 0.89
8 5.90 5.90 5.64 2.83 1.89 1.76 1.13 7.61 12.07 3.30 91.82 25.11
9 0.13 0.13 0.50 0.06 0.04 0.43 0.54 14.84 2.60 7.95 1.39
10 2.19 2.19 2.44 1.05 0.70 0.76 0.49 3.00 10.47 1.38 31.39 4.14
11 9.02 9.02 14.48 4.33 2.89 12.51 19.73 7.55 0.10 148.94 1.97
12 8.13 8.13 9.62 3.90 2.60 8.31 14.82 0.41 4.81 6.07 71.26
13 14.58 14.58 9.25 7.00 4.66 2.89 1.85 16.40 3.40 4.82 55.75 79.03
Fecha:
Reviso:
Calculo:
14 9.95 9.95 2.39 9.27 4.78 3.18 4.30 8.01 20.27 5.91 4.84 119.82 98.12
Proyecto:
15 8.54 8.54 2.39 9.30 4.10 2.73 4.30 8.04 19.17 9.15 4.85 175.38 92.96
16 4.56 4.56 4.64 2.19 1.46 1.45 0.93 6.02 10.77 3.80 64.84 22.88
17 12.72 12.72 9.33 6.11 4.07 2.91 1.87 14.95 11.79 4.86 176.30 72.67
18 1.05 1.05 0.56 0.50 0.34 0.17 0.11 1.13 12.76 3.68 14.38 4.15
19 2.17 2.17 2.35 1.04 0.69 2.03 3.77 14.69 8.28 55.33 31.19
20 2.30 2.30 2.30 1.10 0.74 1.99 3.83 14.69 1.45 56.22 5.55
21 2.39 2.39 3.42 1.15 0.76 2.95 4.87 14.99 4.85 72.95 23.60
199.06 1,520.38 905.81
NORTE 74 # 3809
ING. SALVADOR MELCHOR CRUZ
jueves, 08 de septiembre de 2011
Reviso:
Reviso:
C E N T R O G E O M E T R I C O
(PARA VER LAS DIMENSIONES Y COORDENADAS VER FIGURA DE GEOMETRIA DE CIMENTACION)
COORDENADAS DE CADA FIGURA

FIGURA B H FIGURA X Y
1 5.70 9.67 1 3.15 4.82
2 3.04 3.12 2 7.53 4.76
3 5.74 2.55 3 11.89 8.46
4 6.04 4.70 4 12.07 4.85
5 5.74 2.50 5 11.92 1.25
FIGURA CALCULO DE AREAS

1 -4.50 -0.02 A 1= 5.70 x 9.67 = 55.12 m2
2 -0.12 -0.08 A 2= 3.04 x 3.12 = 9.48 m2
3 4.24 3.62 A 3= 5.74 x 2.55 = 14.64 m2
4 4.42 0.01 A 4= 6.04 x 4.70 = 28.39 m2
5 4.27 -3.59 A 5= 5.74 x 2.50 = 14.35 m2
2
AREA TOTAL = 121.98 m
CENTRO GEOMTRICO =
X=
(xA) =
932.77
= 7.65
m
A 121.98
(yA) 590.27 m
A
Y= = = 4.84
121.98
MOMENTOS DE INERCIA
I1X= 429.53 m4 I1Y= 1263.92 m4
4
I2X= 7.75 m I2Y= 7.43 m4
4
I3X= 199.83 m I3Y= 303.70 m4
I4X= 52.26 m4 I4Y= 641.65 m4
4
I5X= 192.33 m I5Y= 301.41 m4
IX= 881.71 m4 IY = 2518.11 m4
Reviso:
PESO DEL EDIFICIO
AREA DE LA CIMENTACION 121.98 m2

PESO DE LA CIMENTACION 199.06 Ton
MOMENTO DE VOLTEO (X) 859.62 Ton
MOMENTO DE VOLTEO (Y) 876.82 Ton
AREA DE ENTREPISO 122.42 m2
MUROS DE CONCRETO 31.26 m X 0.13 m 2.40 T/m3 X 2.25 m= 21.95 Ton
MUROS DE MAMPOSTERIA 346.29 m X 0.12 m 1.783 T/m3 X 2.25 m= 166.71 Ton
PESO DEL EDIFICIO CON CARGAS MUERTAS
PESO DE PLANTA BAJA 122.42 m2 x 0.365 T/m2 x 1 = 44.68 Ton
PESO DE ENTREPISOS 122.42 m2 x 0.285 T/m2 x 3 = 104.67 Ton
PESO DE LOSA DE AZOTEA 122.42 m2 x 0.265 T/m2 x 1 = 32.44 Ton
PESO DE MUROS DE CONCRETO = 21.95 Ton
PESO DE MUROS DE MAMPOSTERIA = 166.71 Ton
CARGAS DE TINACOS, COLUMNAS, TRABES = 12.00 Ton
PESO DE LA CIMENTACION 199.06 Ton x 1 T/m x 1 = 199.06 Ton
581.51 Ton
PESO DEL EDIFICIO CON CARGA VIVA MEDIA (W)
PESO DE PLANTA BAJA 122.42 m2 x 0.435 T/m
2
x 1 = 53.25 Ton
2
PESO DE ENTREPISOS 122.42 m2 x 0.355 T/m x 3 = 130.38 Ton
PESO DE LA CIMENTACION = 199.06 Ton
617.62 Ton
PESO DEL EDIFICIO CON CARGA INSTANTANEA (Wa)
PESO DE PLANTA BAJA 122.42 m2 x 0.455 T/m2 x 1 = 55.70 Ton
2
PESO DE LOSA DE AZOTEA 122.42 m2 x 0.335 T/m
2
x 1 = 41.01 Ton
634.15 Ton
PESO DEL EDIFICIO CON CARGA VIVA MAXIMA (Wm)
PESO DE PLANTA BAJA 122.42 m2 x 0.535 T/m
2
x 1 = 65.49 Ton
2
676.99 Ton
Reviso:
CALCULO DE CENTRO DE CARGAS EN CIMENTACION
M xpb + M xcim + 7.74 m

X = =
3,685.02 1,520.38
=
W pb + Wcim 473.35 + 199.06
M ypb + M ycim + m
Y = =
2246.15 905.81
=
4.69
W pb + Wcim 473.35 + 199.06
X Y
COORDENADAS DEL CENTRO DE CARGAS 7.74 m 4.69 m
COORDENADAS DEL CENTRO GEOMETRICO 7.65 m 4.84 m
EXCENTRICIDADES -0.09 m -0.15 m
PESO TOTAL= 947.79 Ton (CON FACTOR DE 1.4) MODULO DE SECCION EN X=

2 3
AREA TOTAL= 121.98 m Sx=Ix/Y= 881.71 182.204 m
4 =
MOMENTO DE INERCIA EN Ix= 881.71 m 4.84
MOMENTO DE INERCIA EN Iy= 2518.11 m4
3
Sx=Iy/X= 2518 329.292 m
=
7.65
ESFUERZOS EN EL TERRENO POR CARGA GRAVITACIONAL
MOMENTO EN X= W x ex= 947.79 x 0.09 = 89.4613 ton.m

MOMENTO EN Y= W x ey= 947.79 x 0.15 = 143.635 ton.m
W M X MY 947.79 89.4613 143.635

qn = =
A SX SY 121.98 182.204 329.292
qn= 7.77 0.49 0.44
q1= 8.70 Ton/m2
q2= 7.82 Ton/m2

q= 16.61 Ton/m2
2
q3= 7.72 Ton/m
q4= 6.84 Ton/m2

Reviso:
REVISION DE LA CIMENTACION POR SISMO

ALTURA DEL EDIFICIO= 14.30 m Wedf= 477.93 Ton
ACELERACION ESPECTRAL As= 0.14 Wcim= 199.06 Ton
FACTOR DE REDUCCION Q'= 1.00 Wtotal= 676.99 Ton
LONGITUD DE CIMENTACION EN X= 14.80 m
LONGITUD DE CIMENTACION EN Y= 9.75 m
PROFUNDIDAD DE DESPLANTE= 1.80 m
PESO ESPECIFICO DEL TERRENO= 1.45 Ton/m3
COHESION DEL TERRENO= 2.50 Ton/m2
Fr= 3
MOMENTO DE VOLTEO=M-Mc
2 As 2x 14.30 x 676.99 x 0.141 910.01 Ton
M = HfWt =
3 1
=
3 Q'
1 Df
ENPUJE PASIVO Pp = (2C +
Fr 2
Pp= 1x ( 2 x 2.50 )+( 1.45 x 1.80 )= 2.10 Ton/m2
3 2
MOMENTO RESISTENTE EN X MOMENTO RESISTENTE EN Y
Df 2 Df 2
Mc = PpLx = Mc = PpLy =
2 2
2 2
Mc= 2.10 x 1.80 14.8 x = 50.39 Ton Mc= 2.10 x 9.75 x 1.80 = 33.20 Ton
2 2
MOMENTO DE VOLTEO EN X
Mx= 910.01 - 50.39 = 860 Ton 0.30%Mx= 257.89 Ton
MOMENTO DE VOLTEO EN Y
My= 910.01 - 33.20 = 877 Ton 0.30%My= 263.05 Ton
2
qadm= 1.33 x 16.61 = 22.09 Ton/m
CON SISMO EN DIRECCION X CON SISMO EN DIRECCION Y

W M X MY W M X MY
qn = qn =
A SX SY A SX SY
qnx= 676.99 860 263.05 qnx= 676.99 257.89 877

121.98 182.2 329.29 121.98 182.2 329.29
qnx= 5.55 4.72 0.80 qnx= 5.55 1.42 2.66
2
q1x= 11.07 Ton/m q1y= 9.63 Ton/m2
2 2
q2x= 9.47 Ton/m qadm= 22.09 Ton/m q2y= 4.30 Ton/m2 qadm= 22.09 Ton/m
2
2
q3x= 1.63 Ton/m q3y= 6.80 Ton/m2
2
q4x= 0.03 Ton/m q4y= 1.47 Ton/m2
Reviso:
CALCULO DE DESPLAZAMIENTO Y SEPARACION A

COLINDANCIA
DESPLAZAMIENTOS EN X
Kx Vx x= Vx/Kx
ENTREPISO H (m)
(T/m) (T) (m)
5 12.85 150763 11.84 0.00008

4 10.35 153314 25.92 0.00017
3 7.85 168357 37.24 0.00022
2 5.35 180241 45.46 0.00025
1 2.85 166089 50.22 0.00030
= 0.00102 m
DESPLAZAMIENTOS EN Y
Ky Vy y= Vy/Ky
ENTREPISO H (m)
(T/m) (T) (m)
5 12.85 122958 12.13 0.00010

4 10.35 125827 26.62 0.00021
3 7.85 140406 38.42 0.00027
2 5.35 148866 47.12 0.00032
1 2.85 126163 52.32 0.00041
= 0.00132 m
SEPARACION A COLINDANCIA
SEGN ART. 211 DEL RCDF
ZONA DE LAGO (ZONA II)
DIR X 0.006 18.00 0.108 0.109
DIR Y 0.006 18.00 0.108 0.109
SE DEJARA UNA SEPARACION DE COLINDANCIA DE 15 cm

SEGN PLANO ARQUITECTONICO
Reviso:
DISEO DE LOSA BASE

A B
DATOS
2 3.22 m
WESFUERZOS= 11070 Kg/m a1 =
1
peso de la cimentacion=
199.06/121.98 1632 Kg/m2
WDISEO= 9438 Kg/m2
f'c= 250 Kg/cm2
a2 = 3.59 m
f*c= 200 Kg/cm2

f''c= 170 Kg/cm2
fy= 4200 Kg/cm2
2520 Kg/cm2
a1= 3.22 m
a2= 3.59 m
DC = 20 x 20 cm 2
CALCULO DEL PERALTE MINIMO POR DEFLEXION

(EL TABLERO MAS DESFABORABLE)
LADOS DISCONTINUOS = ( 3.22 + 3.59 ) x 1.25 = 851 cm

LADOS CONTINUOS = 3.22 + 3.59 + = 681 cm
PERIMETRO = 1532 cm
FACTOR DE CORRECCION DEL PERIMETRO = 0.032 4 2520 X 9438
FACTOR DE CORRECCION DEL PERIMETRO = 2.23
1532
dmin = x 2.23 = 13.70 cm
250
USAREMOS LOS SIGUIENTES d= 16 cm

PERALTES h= 20 cm
CALCULO DE MOMENTOS EN FRANJAS CENTRALES
a1= 322 - 10 = 312.0 cm a1 312

a2= 359
= = 0.9
- 10 = 349.0 cm a2 349
10 4 x WU x a12 = 10.-4 x 9438 x 3.22

2
= 9.79
Reviso:
TABLERO MOMENTO CLARO ai Mi (Kg-m)

NEGATIVO EN BORDES CORTO 371 3630.49
INTERIORES LARGO 360 3522.85
DE ESQUINA
(Dos lados
DISCONTINUOS LARGO 206 2015.85
discontinuos)
CORTO 176 1722.28
POSITIVO
LARGO 138 1350.43
Mi Mi f' ' As S(cm)

Q= =
(kg-cm) FR b d f' ' c APEN. A fY (cm2/m) V's#4
363049 0.093 0.084 0.0034 5.44 23.35
352285 0.090 0.083 0.0034 5.38 23.63
214307 0.055 0.073 0.0030 4.73 26.86
201585 0.051 0.080 0.0032 5.18 24.51
172228 0.044 0.080 0.0032 5.18 24.51
135043 0.034 0.080 0.0032 5.18 24.51
REVISION POR CORTANTE
a a
V = 1 d 0.95 0.5 1 w = 6646.4 kg
2 a2
POR BORDES
VU = 1.15 x 6646.4 = 7643.31 kg DISCONTINUOS
VR = 0.50 x FR x b x d f C* = 0.50 x 0.80 x100 x 16 200
VR = 9050.97 kg
PASA, LA SECCION SE ACEPTA POR CORTANTE
CONCLUSIONES
LOSA MACIZA
H=20 cm
V's#4@20cm
AMBOS LECHOS
AMBOS SENTIDOS
Reviso:
DISEO DE LOSA TAPA DE ESTACIONAMIENTO

A B
DATOS
WMUERTA= 365 Kg/m 2
a1 = 3.22 m
2
1
WADICIONAL= 250 Kg/m
f'c= 250 Kg/cm2
f*c= 200 Kg/cm2
a2 =3.59 m
f''c= 170 Kg/cm2

fy= 4200 Kg/cm2
fs= 2520 Kg/cm2
a1= 3.22 m
a2= 3.59 m
DC = 20 20 cm
2


PERIMETRO = 1532 cm
4
FACTOR DE CORRECCION DEL PERIMETRO = 0.032 2520 X 615
1532
dmin = x 1.13 = 6.92 cm
250

PERALTES h= 12 cm
CARGA ULTIMA (Wu)= 615.0 x 1.40 = 861.0 Kg/m2
a1= 322 - 10 = 312.0 cm a1 312

= = 0.9
a2= 359 - 10 = 349.0 cm a2 349
10 4 x WU x a12 = 10.-4 x 861 x 3.22

2
= 0.89
Reviso:

DE BORDE
(Un lado corto
discontinuo)
CORTO 176 157.12
POSITIVO
LARGO 138 123.20
Mi f' ' As S(cm)

Mi Q= =
33120 0.022 0.080 0.0032 3.24 21.93
32138 0.021 0.080 0.0032 3.24 21.93
19551 0.013 0.080 0.0032 3.24 21.93
18390 0.012 0.080 0.0032 3.24 21.93
15712 0.010 0.080 0.0032 3.24 21.93
12320 0.008 0.080 0.0032 3.24 21.93

a a 268.1
V = 1 d 0.95 0.5 1 w = kg
2 a2
POR BORDES
VR = 0.50 x FR x b x d f C* = 0.50 x 0.80 x100 x 10 200
VR = 5656.85 kg
CONCLUSIONES
LOSA MACIZA
H=12 cm
V's#3@20cm
AMBOS SENTIDOS
CON BASTONES
@20cm
Reviso:
DISEO DE LOSA DE ESTACIONAMIENTO

A B
DATOS
WMUERTA= 365 Kg/m 2
a1 = 3.22 m
1
2
f'c= 250 Kg/cm2
f*c= 200 Kg/cm2
a2 =3.59 m
f''c= 170 Kg/cm2

fy= 4200 Kg/cm2
fs= 2520 Kg/cm2
a1= 3.22 m
a2= 3.59 m
DC = 12 x 12 cm
2


PERIMETRO = 1532 cm
4
FACTOR DE CORRECCION DEL PERIMETRO = 0.032 2520 X 535
1532
dmin = x 1.09 = 6.68 cm
250

PERALTES h= 10 cm
a1= 322 - 6 = 316.0 cm a1 316

= = 0.9
a2= 359 - 6 = 353.0 cm a2 353
10 4 x WU x a12 = 10.-4 x 749 x 3.22

2
= 0.78
Reviso:

DE ESQUINA INTERIORES LARGO 360 279.57
(Dos lados NEGATIVO EN BORDES CORTO 219 170.07
adyacentes DISCONTINUOS LARGO 206 159.98
discontinuos) CORTO 176 136.68
POSITIVO
LARGO 138 107.17
Mi f' ' As S(cm)

Mi Q= =
28812 0.029 0.100 0.0040 3.24 21.93
27957 0.029 0.100 0.0040 3.24 21.93
17007 0.017 0.100 0.0040 3.24 21.93
15998 0.016 0.100 0.0040 3.24 21.93
13668 0.014 0.100 0.0040 3.24 21.93
10717 0.011 0.100 0.0040 3.24 21.93

a a 275.1
V = 1 d 0.95 0.5 1 w = kg
2 a2
POR BORDES
VR = 0.50 x FR x b x d f C* = 0.50 x 0.80 x100 x 8 200
VR = 4525.48 kg
CONCLUSIONES
LOSA MACIZA
H=10 cm
V's#3@20cm
AMBOS SENTIDOS
CON BASTONES
@20cm
Reviso:
DISEO DE LOSA DE TINACOS
DATOS
WMUERTA= 260 Kg/m2 a1 = 1.41 m
2 C
f'c= 200 Kg/cm2
f*c= 160 Kg/cm2 a2 =2.17 m
f''c= 136 Kg/cm2
fy= 4200 Kg/cm2
fs= 2520 Kg/cm2
a1= 1.41 m
a2= 2.17 m
DC = 12 x 12 cm D


LADOS CONTINUOS = 2.17 + 1.41 + 0.00 = 358 cm
PERIMETRO = 806 cm
FACTOR DE CORRECCION DEL PERIMETRO = 0.032 4 2520 x 770.0
806
dmin = x 1.19 = 3.85 cm
250

PERALTES h= 10 cm
a1= 141 - 6 = 135.0 cm a1 135

= = 0.6398
a2= 217 - 6 = 211.0 cm a2 211
10 4 x WU x a12 = 10.-4 x 1078 x 1.41 2 = 0.21

Reviso:

AISLADOS
(todos los lados
discontinuos)
CORTO 800 171.45
POSITIVO
LARGO 800 171.45
Mi f' ' As S(cm)

Mi Q= =
11359 0.015 0.100 0.0032 2.59 27.41
11359 0.015 0.100 0.0032 2.59 27.41
11359 0.015 0.015 0.0005 0.38 187.64
11359 0.015 0.015 0.0005 0.38 187.64
17145 0.022 0.022 0.0007 0.57 123.84
17145 0.022 0.022 0.0007 0.57 123.84
a1 a
V = d 0.95 0.5 1 w = 97.5 kg
2 a2
POR BORDES
VR = 0.50 x FR x b x d f C* = 0.50 x 0.80 x100 x 8 160
VR = 4047.72 kg
CONCLUSIONES
LOSA MACIZA
H=10 cm
V's#3@20cm
AMBOS SENTIDOS
AMBOS LECHOS
Reviso:
Reviso:
DISEO DE CONTRATRABE CT-1

D A T O S
18
A F
L= 3.59 m
B= 0.20 m L = 2.88m
H= 1.80 m 19
AT = 3.00 m2
W= 9.44 t/m2
W= 8.75 t/m
f'c = 250 Kg/cm2 W = 10.04 t/m2
f*c = 200 Kg/cm2
f''c = 170 Kg/cm2
fY = 4200 Kg/cm2 L 3.59
= 1.99 < 2.5
H =
Fr = 0.9 (Flexin) 1.8
Fr = 0.8 (Cortante) SE DISEARA COMO VIGA APERALTADA
REFUERZO POR FLEXION EN EXTREMOS

W L2 2
MU = 1.4 = x
8.75 3.59
12 1.40 x = 13.16 t-m
12
W L 1.4 8.75 3.59 21.99
V = 1.4 = x
2 2
MR = F R AS F Y Z ..... NTC-2.1.2.e
L L
Z = 0.3 + 0.20 H =
H H
3.59
Z = 0.3 + 0.20 x 1.8 = 1.26 m
1.8
MR 1315796.7
AS = = = 2.77 cm2
FR fY Z 0.9 x 4200 x 125.8
0.7 f' C 0.70 250

PMIN = = = 0.0026
fY 4200
cm2
AS MIN = 0.0026 x 20 x 125.80 = 6.630
"Sin embargo, no es necesario que el refuerzo mnimo sea mayor que 1.33 veces el requerido por
anlisis" (NTC-C 2.1.2.a)
3.68 cm
2
POR LO TANTO AS MIN = 2.77 x 1.33 =
Reviso:
L
.5 3 AS
h
L
.5 1AS
h
ACERO DE REFUERZO EN FRANJAS

INTERMEDIAS
3.59
0.5 3 - x 3.68 = 1.85 cm2
1.8
CON No.3 aS = 0.71m2
1.85
N = = 2.61 BARRAS
0.71
SE COLOCARAN V's#3@20

INFERIORES
0.50 3.59 - 1 x 3.68 = 1.83 cm2

1.8
CON No. 4 aS = 1.27 cm2
1.83
N = = 1.44 BARRAS
1.27
SE COLOCARAN 2V's#4
REFUERZO POR FLEXION EN CLARO CENTRAL

W L2 8.75 x 3.59
2
MU = 1.4 = 1.40 x = 6.58 t-m
24 24
MR = F R AS F Y Z ..... NTC-2.1.2.e
L L
Z = 0.3 + 0.20 H SI 1.0 < 2.5
H H
Z = 0.3 + 0.20
3.59
x 1.8 = 1.26 m
1.8
Reviso:
MR 657898.4
= 1.38 cm
2
AS = =
FR fY Z 0.9 x 4200 x 125.8
0.7 f' C 0.70 250

PMIN = = = 0.0026
fY 4200
cm2
AS MIN = 0.0026 x 20 x 125.80 = 6.630
"Sin embargo, no es necesario que el refuerzo mnimo sea mayor que 1.33 veces el requerido por
anlisis" (NTC-C 2.1.2.a)
1.84 cm
2
POR LO TANTO AS MIN = 1.38 x 1.33 =
L
0.2 0.05 h
h
PERO NO MAYOR
QUE 0.2L

SUPERIORES
CON No. 4 aS = 1.27 cm2
0.2 - 0.05 359 1.84
x 180 = 18.05cm N = = 1.45 BARRAS
180 1.27
SE COLOCARAN 2 V's#4
CORTANTE QUE TOMA EL CONCRETO

W L 8.75 x 3.59
VU = 1.4 = 1.40 x = 21.99 t
2 2
Si L/h es menor que 4 y las cargas y reacciones comprimen directamente las caras superior e inferior de la viga, Vcr
se aplicar la ecuacin 2.20 multiplicado por "
M 2.65
3.5 2.5 1.0 =
Vd
VCR = FR bd (0.20 + 20 p )f *C .... NTC-C 2.5.1.1 (2.19)
VCR = 0 .80 x 20 x 180 x (.20 + 20* ( 0.00073
)) x 200
VCR = 8.7 ton
VCR = 0.5 FR b f *dC .... NTC-C 2.5.1.1 (2.20)

VCR = 0.5 x .80 x 20 x 180 x 200 = 20364.68 kg
VCR = 20.4 ton
Reviso:
L 3.59
SI
H
= = 1.99 VCR = 20.36 ton
1.8
VCR= 2.655 X 20.4 = 54.07 ton
Cuando la dimension transversal h es mayor que 700 mm, el valor de VCR debera multiplicarse
11 0.0 0 0 4 (h 7 0 0) 0.8 2.5.1 (2.18)
VCR = 0.8 x 54.07 = 43.25 ton
SEPARACION DE ESTRIBOS (usando V's#3)
SI VCR > VU
"Se suministrara un refuerzo minimo con una cuantia igual a 0.003
Asv= 0.003 20 180 10.8
CON V's# 9 1.42 6.34 7
S AV= 180 7 26
S AV= 20cm
REVISIN COMO MURO DE CONCRETO

La relacin entre el rea de refuerzo vertical y el rea total de la seccin no ser menor que 20
fY
20 20
= = 0.004762
fY 4200
AS = 20 x100 xx 0.0048 = 9.5 cm2
2.2
9.52 2.40
N = = 6.76
0.71
100
S= = 14.29 cm
7
NT-2.4
CONCLUSION
1)
Reviso:
DISEO DE TRABE CT-2

DATOS ENTRE C-E
L= 3.59 m
1 2
w= 9438 Kg/m2
2
A= 5.61 m
wl= 14749 Kg/m
G
H
W viga= 288 Kg/m
wt= 15037 Kg/m
B
b= 0.20 m
H= 0.60 m (+)
d= 0.55 m
2
(-)
f'c= 250 Kg/cm
2
f*c= 213 Kg/cm
2
f''c= 170 Kg/cm
fy= 4200 Kg/cm2
2 (+)
Es= 2000000 Kg/cm
1= 0.85
FR= 0.9 FLEXION
FR= 0.8 CORTANTE
ri= 0.05 m
EV's#= 3
Gpo= b
Fsismicas= SI
conceto clase= 1
wl 2
MOMENTO MAXIMO M MAX = = 15037 x 12.89 = 16149 Kg.m
12 12
MOMENTO ULTIMO = 1x 16149 = 16149 = 1614935 Kg.cm
CORTANE WL x 1= 15.04 3.59 = 26.99 ton

2 2
LAS SECCIONES RECTANGULARES SIN ACERO DE COMPRESION, TIENEN FALLA BALANCEADA CUANDO:
f ' ' c 6000 1

= 170 x 6000 x 0.85 = 0.0202
fy fy + 6000 4200 4200 + 6000
EL AREA MAXIMA DE ACERO DE TENSION EN SECCIONES DE CONCRETO REFORZADO, QUE NO DEBAN RESISTIR
FUERZAS SISMICAS SERA EL 90% DE LA QUE CORRESPONDA A LA FALLA BALANCEADA DE LA SECCION
CONSIDERADA, EN CASO CONTRARIO SERA DEL 75%2.2.2 N.T.C.C.
p= 0.75 x 0.0202 = 0.015179
fy 0.0151786 x 4200 = 0.375

q= =
f ''c 170
EL AREA DE ACERO SERA

Reviso:
Mu
As = = 1614935 = 8.60 cm2
fyd (1 0.5q ) 4200 X 55 x( 1- 0.5 x 0.4
CON V's# 6 = 8.60 = 3.02

2.85
As= 2.85 x 4= 11.4 cm2 At= 11.4
2.85 x 0= 0 cm2
0.7 f ' c
AREA DE ACERO MINIMO As MIN = bd = 0.7 16 X 55 x 20 = 2.90 cm2
fy 4200
MOMENTO RESISTENTE CON EL AREA DE ACERO ASIGNADA M R = FR Asfyd (1 0.5q ) =

Mr= 0.9 x 11.4 x 4200 x 55 ( 1- 0.5 x 0.375 )= 1925674
como 1925673.8 > 1614935 se acepta la seccion
EL MOMENTO RESISTENTE DE LA SECCION DEBERA DE SER POR LO MENOS 1.5 VECES EL MOMENTO DE AGRIETAMIENTO
DE LA SECCION TRANSFORMADA NO AGRIETADA
bh 3 cm4
Ig = =
3
20 x 60 = 360000
12 12
Kg/cm2
f f= 2
f' = 2
250 = 31.62
f f Ig
Mag = = 31.62 x 360000 = 379473.3 Kg.cm
h2 30
CALCULO DE LAS DEFLEXIONES
Ec= 14000 f ' c= 14000 x 16 =
2
n= Es = 2000000 = 9.04 Ec= 221359.4 Kg/cm
Ec 221359.44
nAs= 9.04 11.4 = 103.00 cm2 SECCION TRANSFORMADA
PROFUNDIDAD DEL EJE NEUTRO bc 2

= nAs ( d c )
2
20 c
2
= 103.00 ( 55 - c) b b 2 4ac
c= =
2 2a
c2 + 10.3 c - 566.4995 = 0 c= 19.20 cm
bc 3

EL MOEMNTO DE INERCIA AGRIETADO VALE I a g = n As(d c) 2 + =
3
2
Iag= 103.00 55 - 19.20 + 20 x 7080 = 179195 cm4
3
Reviso:
MOMENTO DE INERCIA EFECTIVO
Mag
3
Mag 3
Ie = Ig + 1 Iag Ig
M max M max
3
Ie= 379473.32 360000 + 1- 379473.3 179195 =
1614934.6 1614935
Ie= 4671 + 176870 = 181541
SE DEBE DE CUMPLIR Ie<Ig 181541 < 360000 CUMPLE
PARA LA CARGA UNIFORME
wL 4
= = 150.37 x 359 = 0.162 cm
384 EI 384 x 221359.4 x 181541
DONDE i= 0.7 x 0.162 = 0.11 cm INMEDIATA

DONDE i= 0.3 x 0.162 = 0.05 cm COMPLEMENTARIA
2
dif= i = 0.11 2 = 0.226
1 + 50 ' 1+ 0.003
p'= 3x 1.27 = 0.003
20 x 55
DEFLEXION TOTAL= 0.11 + 0.05 + 0.226 = 0.39 cm
DEFLEXION ADMISIBLE= (L/240)+0.5= 359 + 0.5 = 2.00 cm

240
COMO 2.00 > 0.39 SE ACEPTA
DISEO POR CORTANTE
VCR= FR b d ( 0.2 + 20 p ) fc* ... SI < 0.015 NTC-C 2.5.1.1 (2.19)

x
VCR= 0.8 x 20 x 55( 0.2+20 x 0.015179 ) x 213 = 6.46 TON
c
VCR= 0.5 FR b d fc* ... SI 0.015 NTC-C 2.5.1.I (2.20)
x =
VCR= 0.5 x 0.8 x 20 x 55 x 212.5 = 6.41 TON
COMO p= > 0.015 ENTONCES
VCR= 6.41 TON

Reviso:
EL CORTANTE ULTIMO SE TOMA A UN PERALTE Y POR LO TANTO VALE
Vu= 27.0 - 21.1 x 0.55 = 15.41 TON
SI VU > VCR
FR A V fY d = 0.8 x 1.4 x 4.2 x 55 = 29 cm

S = =
15.41 - 6.41
VU - VCR
SI VCR < VU 1.5 FR b d fc * . . . S = 0.5 d
6.41 < 15.41 19.24 s= 28 cm
SI VU > 1.5 FR b d fc* . . . S = 0.25 d
15 > 19 s= 14 cm
EN NINGUN CASO SE PERMITIRA QUE

VU > 2.5 FR b d fc*
15.41 > 32.07
20
3 V's# 6
60 EST# 3@ 20 cm
4 V's# 6
CT-2
Reviso:
DISEO DE TRABE T-2

DATOS ESCALERA
L= 3.08 m
w= 715 Kg/m2 D E
A= 4.52 m2
wl= 1049 Kg/m
W viga= 108 Kg/m H
wt= 1157 Kg/m

B
b= 0.15 m
H= 0.30 m
(+)
d= 0.28 m
2 (-)
f'c= 200 Kg/cm
2
f*c= 170 Kg/cm
2
f''c= 136 Kg/cm
fy= 4200 Kg/cm2
2
Es= 2000000 Kg/cm (+)
1= 0.85
FR= 0.9 FLEXION
FR= 0.8 CORTANTE
ri= 0.02 m
EV's#= 2
Gpo= b
Fsismicas= SI
conceto clase= 2
wl 2
MOMENTO MAXIMO M MAX = = 1157 x 9.49 = 915 Kg.m
12 12
MOMENTO ULTIMO = 1.4 x 915 = 1281 = 128082 Kg.cm
CORTANE WL x 1.4 = 1.16 3.08 = 1.78 ton

2 2
LAS SECCIONES RECTANGULARES SIN ACERO DE COMPRESION, TIENEN FALLA BALANCEADA CUANDO:
f ' ' c 6000 1

= 136 x 6000 x 0.85 = 0.0162
fy fy + 6000 4200 4200 + 6000
p= 0.75 x 0.0162 = 0.012143
fy 0.012143 x 4200 = 0.375

q= =
f ''c 136
EL AREA DE ACERO SERA

Reviso:
Mu
As = = 128082 = 1.34 cm2
fyd (1 0.5q ) 4200 X 28 x( 1- 0.5 x 0.4
CON V's# 4 = 1.34 = 1

1.27
As= 1.27 x 3= 3.81 cm2
0.7 f ' c
AREA DE ACERO MINIMO As MIN = bd = 0.7 14 X 28 x 15 = 0.99 cm2
fy 4200
MOMENTO RESISTENTE CON EL AREA DE ACERO ASIGNADA M R = FR Asfyd (1 0.5q ) =

Mr= 0.9 x 3.81 x 4200 x 28 ( 1- 0.5 x 0.375 )= 327641
como 327641 > 128082 se acepta la seccion
EL MOMENTO RESISTENTE DE LA SECCION DEBERA DE SER POR LO MENOS 1.5 VECES EL MOMENTO DE AGRIETAMIENTO
bh 3 cm4
Ig = =
3
15 x 30 = 33750
12 12
Kg/cm2
f f=
1.4 f' = 1.4
200 = 19.80
f f Ig
Mag = = 19.80 x 33750 = 44547.73 Kg.cm
h2 15
CALCULO DE LAS DEFLEXIONES
Ec= 11000 f ' c= 11000 x 14 =
2
n= Es = 2000000 = 12.86 Ec= 155563.5 Kg/cm
Ec 155563.5
nAs= 12.86 3.81 = 48.98 cm2 SECCION TRANSFORMADA
PROFUNDIDAD DEL EJE NEUTRO bc 2

= nAs ( d c )
2
15 c
2
= 48.98 ( 28 - c) b b 2 4ac
c= =
2 2a
c2 + 6.5 c - 182.8707 = 0 c= 10.65 cm
bc 3

EL MOEMNTO DE INERCIA AGRIETADO VALE I a g = n As(d c) 2 + =
3
2
Iag= 48.98 28 - 10.65 + 15 x 1207 = 20785 cm4
3
Reviso:
Mag
3
Mag 3
Ie = Ig + 1 Iag Ig
M max M max
3
Ie= 44547.73 33750 + 1- 44547.73 20785 =
91487.29 91487.29
Ie= 3896 + 18385 = 22282
SE DEBE DE CUMPLIR Ie<Ig 22282 < 33750 CUMPLE
wL 4
= = 11.57 x 308 = 0.078 cm
384 EI 384 x 155563.5 x 22282

2
dif= i = 0.05 2 = 0.109
1 + 50 ' 1+ 0.009
p'= 3x 1.27 = 0.009
15 x 28

240
DISEO POR CORTANTE
VCR= FR b d ( 0.2 + 20 p ) fc* ... SI < 0.015 NTC-C 2.5.1.1 (2.19)

x
VCR= 0.8 x 15 x 28( 0.2+20 x 0.012143 ) x 170 = 1.94 TON
c
VCR= 0.5 FR b d fc* ... SI 0.015 NTC-C 2.5.1.I (2.20)
VCR= 0.5 x 0.8 x 15 x 28 x 170 = 2.19 TON
COMO p= < 0.015 ENTONCES
VCR= 1.94 TON

Reviso:
EL CORTANTE ULTIMO SE TOMA A UN PERALTE Y POR LO TANTO VALE
Vu= 1.8 - 1.62 x 0.28 = 1.33 TON
SI VU > VCR
FR A V fY d = 0.8 x 0.6 x 4.2 x 28 = -98 cm

S = =
1.328564 - 1.94
VU - VCR
SI VCR < VU 1.5 FR b d fc * . . . S = 0.5 d
1.94 < 1.33 6.57 s= 14 cm
SI VU > 1.5 FR b d fc* . . . S = 0.25 d
1.3 > 6.6 s= 7 cm

VU > 2.5 FR b d fc*
1.33 > 10.95
15
3 V's# 4
30 EST# 2@ 15 cm
3 V's# 4
T-2
Reviso:
DISEO DE DALAS DE
CERRAMIENTO (D-C)
D A T O S
t= 12 cm
hC = 25 cm
f'c = 200 Kg/cm2
f*c = 160 Kg/cm2
f''c = 136 Kg/cm2
fY = 4200 Kg/cm2 ACERO LONGITUDINAL
fY = 2530 Kg/cm2 ACERO TRANSVERSAL
AUNQUE EL REGLAMENTO PERMITE CONFINAR HORIZONTALMENTE AL MURO DE MAMPOSTERIA CON

ELEMENTOS DE CONCRETO DE POR LO MENOS 10 cm DE PERALTE, EN ESTE CASO EMPLEAREMOS UN
PERALTE
hC = 25 cm
CON LO QUE SE CUMPLE QUE
hC = > t
EL CONCRETO DE TENDR UNA RESISTENCIA A
COMPRESION, f' C , NO MENOR DE 150 kg/cm2 . . . . . . . . . . . . . . . . . . NTC-M 3.3
f'c = 200 Kg/cm2 SI CUMPLE

EL REFUERZO LONGITUDINAL ESTARA FORMADO POR
ALMENOS 3 BARRAS CUYA AREA TOTAL SERA: . . . . . . . . . . . . . . . . . . NTC-M 3.3
'
fC
A S = 0.20 t2 200 2
fY = 0.2 x x 12 = 1.37 cm2
4200
con V's #3 aS = 0.71 cm2 se usaran 4V's#3
EL REFUERZO TRANSVERSAL ESTARA FORMADO POR

ESTRIBOS CERRADOS CON UN AREA (ASC) MINIMA DE: . . . . . . . . . . . . . . . . . . NTC-M 3.3
1000 S 1000 x 20
A SC = 0.32 cm2
fY hc 2530 x 25
LA SEPARACION DE LOS ESTRIBOS NO EXCEDERA DE:
. . . . . . . . . . . . . . . . . . NTC-M 3.3
1.5 t = 1.5 x 12 = 18 cm
S
200 mm
con V's #2 aS = 0.32 cm2 se usaran V's#2@20

12
25
4V's#3
CONCLUSION
Reviso:
DISEO DE MURO DE CONCRETO MC-1
DATOS
L= 3.06 m MURO 15
t= 0.13 m SEGN 6.5.2.1 NTCC e(min)=13cm
Hm= 2.50 m
Vu 16.3 Ton
Pu= 10.37 Ton
Mu= 154.65 Ton.m
2
f'c= 200 kg/cm
2
f*c= 170 kg/cm
2
f''c= 136 kg/cm
2
fy= 4200 kg/cm
Fr= 0.9 FLEXION
Fr= 0.8 CORTANTE
b) LA CARGA DEL MURO DEBE SER MENOR QUE, SI 0.30f'c Ag, Y ADEMAS L/t NO MAYOR QUE 70
0.3 x 200 x 306 x 13 = 238,680 > 10,370 SI CUMPLE
L/t <70 ; 306 13 = 24 < 70 SI CUMPLE
Hm
c) DISEO POR FLEXOCOMPRESION, EN MUROS EN QUE 2 SE CONSIDERARA AL
L
MOMENTO FLEXIONANTE DE DISEO, A LO LARGO DE Hcr, CON UN VALOR CONSTANTE E IGUAL A Mu
Hm
L
2 2.50
3.06
=
0.82 < 2 NO CUMPLE se diseara como muro
SE DISEARA CON LA FORMULA 2.15 DE LA NTCC M R = FR AS fyZ
SE DEBERA CUMPLIR QUE PU 0.30 FR tLf ' c

10,370 < 0.3 x 0.9 x 13 x 306 x 200 = 214,812 kg SI CUMPLE
d)PARA DETERMINAR EL VALOR DE Z SE UTILIZARA EL CRITERIO SIGUIENTE
Z = 1.20 Hm SI Hm 2.5 = 0.82 NO APLICA
Z= 1.2 x 2.5 = 3m
0.5 3.06
L
Hm Hm
SI 0.5 < 1 NO APLICA
Z = 0.41 + L L
L
Z= 2.22 m
Hm
Z = 0.8 L SI 1.00 < 0.8 NO APLICA
z= 2.45 m L
POR LO TANTO Z= 2.22 m
e) EL AREA DE ACERO VERTICAL SE CALCULARA CON LA FORMULA SIGUIENTE
MR = cm2
AS = 15465000 = 15.48 CON 16 V's# 4
2
FR f y Z 0.9 x 5000 x 222 As= 16 x 1.27 = 20.3 cm
f) CUANTIA DE REFUERZO VERTICAL
p= As/ t z = 20.3 = 0.007 < 0.008 SI CUMPLE 6.5.2.3 NTCC
13 x 222
g) COLOCACION DEL REFUERZO VERTICAL
SI LA RELACION Hm/L ES MENOR QUE 1.20, SE COLOCARA EN UN ANCHO IGUAL A
0.10 H m ( 0.25 - 0.1 x 2.50 )x 3.06 = 0.515 cm
0.25 L = 3.06
L
NI MAYOR QUE 0.40Hm= 0.4 x 2.50 = 1 m
SE TOMARA EL TRAMO DE= 45 cm
SI LA RELACION Hm/L ES MAYOR QUE 1.20, SE COLOCARA EN UN ANCHO IGUAL 0.15 L

POR LO TANTO 0.15 x 3.06 = 0.459 m SI APLICA
0.50 SE DEJARAN
8 V's# 4
0.13 EN CADA EXTREMO Y
cm V's# 3@
0.24 m
z= 2.22
Reviso:
DATOS
L= 1.28 m MURO 16
Hm= 2.50 m
Vu 6.98 Ton
Pu= 41.84 Ton
Mu= 41.83 Ton.m
2
f'c= 200 kg/cm
2
f*c= 170 kg/cm
2
f''c= 136 kg/cm
2
fy= 4200 kg/cm
Fr= 0.9 FLEXION
Fr= 0.8 CORTANTE
0.3 x 200 x 128 x 20 = 153,600 > 41,840 SI CUMPLE
L/t <70 ; 128 20 = 6.4 < 70 SI CUMPLE
Hm
L
Hm
L
2 2.50
1.28
=

41,840 < 0.3 x 0.9 x 20 x 128 x 200 = 138,240 kg SI CUMPLE
Z= 1.2 x 2.5 = 3m
0.5 1.28
L
Hm Hm
SI 0.5 < 1 SI APLICA
Z = 0.41 + L L
L
Z= 1.51 m
Hm
Z = 0.8 L SI 1.00 < 2 SI APLICA
z= 1.02 m L
MR = cm2
AS = 4183000 = 9.11 CON 8 V's# 5
2
FR f y Z 0.9 x 5000 x 102 As= 8 x 1.98 = 15.8 cm
20 x 102
0.10 H m ( 0.25 - 0.1 x 2.50 )x 1.28 = 0.07 cm
0.25 L = 1.28
L
NI MAYOR QUE 0.40Hm= 0.4 x 2.50 = 1 m

0.20 SE DEJARAN
4 V's# 5
cm V's# 3@
0.15 m
z= 1.02
Reviso:
DATOS
L= 1.92 m MURO 19
Hm= 2.50 m
Vu 12.88 Ton
Pu= 31.38 Ton
Mu= 136.76 Ton.m
2
f'c= 200 kg/cm
2
f*c= 170 kg/cm
2
f''c= 136 kg/cm
2
fy= 4200 kg/cm
Fr= 0.9 FLEXION
Fr= 0.8 CORTANTE
0.3 x 200 x 192 x 20 = 230,400 > 31,380 SI CUMPLE
L/t <70 ; 192 20 = 9.6 < 70 SI CUMPLE
Hm
L
Hm
L
2 2.50
1.92
=

31,380 < 0.3 x 0.9 x 20 x 192 x 200 = 207,360 kg SI CUMPLE
Z= 1.2 x 2.5 = 3m
0.5 1.92
L
Hm Hm
Z = 0.41 + L L
L
Z= 1.77 m
Hm
Z = 0.8 L SI 1.00 < 1.3 SI APLICA
z= 1.54 m L
MR = cm2
AS = 13676000 = 19.73 CON 12 V's# 5
2
FR f y Z 0.9 x 5000 x 154 As= 12 x 1.98 = 23.8 cm
20 x 154
0.10 H m ( 0.25 - 0.1 x 2.50 )x 1.92 = 0.23 cm
0.25 L = 1.92
L
NI MAYOR QUE 0.40Hm= 0.4 x 2.50 = 1 m

0.30 SE DEJARAN
6 V's# 5
cm V's# 3@
0.15 m
z= 1.54
Reviso:
DATOS
L= 1.92 m MURO 19
Hm= 2.50 m
Vu 7.01 Ton
Pu= 24.43 Ton
Mu= 52.23 Ton.m
2
f'c= 200 kg/cm
2
f*c= 170 kg/cm
2
f''c= 136 kg/cm
2
fy= 4200 kg/cm
Fr= 0.9 FLEXION
Fr= 0.8 CORTANTE
0.3 x 200 x 192 x 13 = 149,760 > 24,430 SI CUMPLE
L/t <70 ; 192 13 = 15 < 70 SI CUMPLE
Hm
L
Hm
L
2 2.50
1.92
=

24,430 < 0.3 x 0.9 x 13 x 192 x 200 = 134,784 kg SI CUMPLE
Z= 1.2 x 2.5 = 3m
0.5 1.92
L
Hm Hm
Z = 0.41 + L L
L
Z= 1.77 m
Hm
Z = 0.8 L SI 1.00 < 1.3 SI APLICA
z= 1.54 m L
MR = cm2
AS = 5223000 = 7.54 CON 12 V's# 4
2
FR f y Z 0.9 x 5000 x 154 As= 12 x 1.27 = 15.2 cm
13 x 154
0.10 H m ( 0.25 - 0.1 x 2.50 )x 1.92 = 0.23 cm
0.25 L = 1.92
L
NI MAYOR QUE 0.40Hm= 0.4 x 2.50 = 1 m

0.30 SE DEJARAN
6 V's# 4
cm V's# 3@
0.23 m
z= 1.54
Reviso:
DIAGRAMA DE MOMENTOS T-1
X
Y
F D C B
L J G A
ECOgcW V2.18 -NORTE-74 (2) ECO-

Reviso:
DIAGRAMA DE CORTANTES T-1
X
Y
F D C B
L J G A

Reviso:
DISEO DE TRABE T-1

EJE B, ENTRE 1-5
DATOS
f'c= 250 kg/cm2 CONCRETO CLASE = 1
f*c= 213 kg/cm2 Es= 2000000 kg/cm2
f''c= 170 kg/cm2 L= 4.74 m
fy= 4200 kg/cm2 w= 5898 Kg/m
2
fs= 2520 kg/cm B= 0.85
b= 25 cm
Fr= 0.9 FLEXION
Fr= 0.8 CORTANTE
EST#3= 3
Mmax= 4.78 Ton.m = 478000 kg.cm ESTREMO EJE 2
M1= 2.456 Ton.m = 245600 kg.cm CENTRAL
M2= 1.506 Ton.m = 150600 kg.cm EXTREMO EJE 5
Fsismicas= SI
EL AREA MAXIMA DE ACERO EN TENSION, SERA LA CORRESPONDIENTE, A LA FALLA BALANCEADA
f ' ' c 6000 170 x 6000 x 0.85 = 0.0202

= =
fy 6000 + fy 4200 6000 + 4200
pfy 0.0202 4200 = 0.500

q= =
f ''c 170
M R = FR bd 2 f ' ' cq (1 0.5q ) =
MR 478000 =
d = =
FR bf ' ' q (1 0.5q ) 0.9 25 170 0.5000 ( 1 - 0.5 0.5000 )
d= 333.2462 = 18.25503 PERO SE DEJARA d= 45 cm
CALCULO DEL AREA DE ACERO
p= 0.75 x 0.0202 = 0.0152
fy
q= = 0.0152 x 4200 = 0.375
f ''c 170
3
As = pbd = 0.0100 x 25 x 45 = 11.25 cm2 V'S#
EJE 2 6
CON V's# 6 TENEMOS 11.25 = 3.95 = 3 V'S# 6
2.85
LAS OTRAS AREAS DE ACERO PARA DIFERENTES MOMENTOS LAS OBTENEMOS POR IGUALACION, TENEMOS
11.25 = 478000 As= 11.25 x 245600 = 5.780335

X = 245600 478000
CON V's# 6 TENEMOS 5.78 = 2.03 = 3 V'S#6

2.85
11.25 = 478000 As= 11.25 x 150600 = 3.544456 CENTRAL

X = 150600 478000
Reviso:
CON V's# 6 TENEMOS 3.54 = 1.24 = 3 V'S#6

2.85
AREA DE ACERO MINIMO EJE 5
0.7 f ' c
As min = bd =
2
0.7 250 25 45 = 2.96 cm
fy 4200
EL MOMENTO RESISTENTE DE LA SECCION DEBERA DE SER POR LO MENOS 1.5 VECES EL MOMENTO DE AGRIETAMIENT
4
bh 3 25 x 49 = 245102.1 cm
Ig = =
12 12
f' = 250 =
ff= 2 2 31.62 Kg/cm
f f Ig 31.62 x 245102.1 = 316359.5 x 1.5 = 474539.3 kg.cm

Mag = = 24.5
h2
M R = FR Asfyd (1 0.5q ) =
= 0.9 x 8.55 x 4200 x 45 x 1 - 0.5 0.375 = 1181663 kg.cm
COMO Mr > 1.5Magr 1181663 > 474539.3 SE ACEPTA
SE DEJARAN 3 V's # 6 EN TODA LA LONGITUD QUE CUBREN LOS MOMENTOS DE LAS SECCIONES RESTANTES
CORTANTE RESISTENTE VCR = FR bd (0.2 + 20 p ) f * c =

Vcr= 0.8 x 25 x 45 ( 0.2 + 20 x 0.0202 ) 213 = 7934.26
Vu= 12.06 = 12060
SEPARACION DE ESTRIBOS POR CORTANTE PARA LA SECCION CRITICA
FR AV f y d
S= = 0.8 x 1.42 x 4200 x 45 = 52 cm
VU V R 12060 - 7934.26
SI Vu ES MAYOR QUE Vcr PERO MENOR O IGUAL QUE:
1.5 FR bd f *c = 1.5 x 0.8 x 25 x 45 x 213 = 19679.46
19679.46 > 12060 > 7934.26
LA SEPARACION DEBERA DE SER 0.5d = 0.5 x 45 = 22.5 cm NO APLICA
SI Vu> 1.5 FR bd f *c =
12060 > 19679.46
LA SEPARACION DEBERA DE SER 0.25d S= 0.25 x 45 = 11.25 cm NO APLICA
SEPARACION DE ESTRIBOS POR CORTANTE PARA LAS DEMAS SECCIONES

Reviso:
Vu= 10.92 = 10920

CUANDO LA FUERZA CORTANTE DE DISEO Vu SEA MENOR QUE Vcr, EL AREA DE REFUERZO MINIMO PARA VIGAS
SERA LA CALCULADA CON LA SIGUIENTE EXPRESION, CUYA SEPARACION NO EXCEDERA DE d/2
S= 45 = 22.5 cm SE DEJARA UNA SEPARACION DE 20cm

2
bs 0.3 x 14.58 X 25 x 22.5 = 0.59 cm2
Av min = 0.30 f * c =
fy 4200
2
CON 2 V'S# 3 = 2 x 0.71 = 1.42 cm
SE DEJARAN ESTRIBOS CON VARILLAS DEL # 3 @ 20 cm

VU > 2.5 FR b d fc* 12060 > 2.5 x 0.8 x 25 x 45 x 15
12060 < 32799 SE ACEPTA
CALCULO DE MOMENTOS DE INERCIA EXTREMO EJE 5
Ec= 11000 f ' c= 11000 x 15.8 = 173925.3

2
Ec= 173925.3 Kg/cm
n= Es = 2000000 = 11.50
2
Es= 2000000 Kg/cm Ec 173925.3
SECCION TRANSFORMADA nAs= 8.55 x 11.50 = 98 cm2
PROFUNDIDAD DEL EJE NEUTRO bc 2 b b 2 4ac

= nAs ( d c ) c= =
2 2a
2
25 c = 98.32 ( 45 - c)
2
2
12.5 c = 4424.314 - 98.32 c
C= 15.29 cm
2
0 = 1.25 c + 9.83 c - 442.4
bc3
EL MOMENTO DE INERCIA AGRIETADO VALE I a g = n As(d c) 2 + =
3
Iag= 98.32 x( 45 - 15.29 )2+ 25 15.29

3
= 116571.8 cm4
3
CALCULO DE MOMENTOS DE INERCIA EXTREMO EJE 2
SECCION TRANSFORMADA nAs= 8.55 x 11.50 = 98 cm2
bc 2
= nAs ( d c )
b b 2 4ac
PROFUNDIDAD DEL EJE NEUTRO
c= =
2 2a
2
25 c = 98 ( 45 - c)
2
2
12.5 c = 4424 - 98 c
0 = 1.25 + 9.8 c - 442 C= 15.29 cm
Iag= 98 X( 45 - 15.29 )2+ 25 15.29

3
= 116571.8 cm4
3
CALCULO DE MOMENTOS DE INERCIA EXTREMO CENTRAL
SECCION TRANSFORMADA nAs= 8.55 x 11.50 = 98.3 cm2

Reviso:
PROFUNDIDAD DEL EJE NEUTRO bc 2 b b 2 4ac

= nAs ( d c ) c= =
2 2a
2
25 c = 98.32 ( 45 - c)
2
2
12.5 c = 4424.314 - 98.32 c
C= 15.29 cm
2
0 = 1.25 c + 9.83 c - 442.4
bc3
EL MOMENTO DE INERCIA AGRIETADO VALE I a g = n As(d c) 2 + =
3
Iag= 98.32 x( 45 - 15.29 )2+ 25 15.29 3
= 116571.8 cm4
3
I1 + I 2 + 2I 3
MOMENTO DE INERCIA TOTAL I AG = =
4
Iag= 116571.8 + 116571.8 + 2x 116571.8 = 116571.8 cm4
4
Mag
3
Mag 3
Ie = Ig + 1 Iag Ig
M max M max
3 3
Ie= 474539.3 245102.1 + 1 - 474539.3 116571.8 = 242330.6 cm4
478000 478000
SE DEBE DE CUMPLIR Ie<Ig 242331 < 245102.1 CUMPLE
wL 4 x = cm
= = 58.98 474 0.1840
384 EI 384 x 173925.3 x 242331

2
dif= i = 0.13 2 = 0.256
1 + 50 ' 1+ 0.008

240

Reviso:
ELEMENTOS MECANICOS T-1
ENVOLVENTE DE ELEMENTOS MECANICOS

Miembro X (m) Comb F.Axial F.Cortante2 F.Cortante3 M.Torsin M.Flexion2 M.Flexion3
(T) (T) (T) (T*m) (T*m) (T*m)
3+A-B/1 0.000 DI1 0.000 2.525 0.000 -0.128 0.000 1.506
DI26 0.000 1.469 0.000 0.031 0.000 0.846
DI29 0.000 2.115 0.000 -0.214 0.000 1.310
1.320 DI1 0.000 1.271 0.000 -0.128 0.000 -0.999
DI26 0.000 0.615 0.000 0.031 0.000 -0.530
DI29 0.000 1.262 0.000 -0.214 0.000 -0.919
3+B-C/1 0.000 DI26 0.000 1.097 0.000 -0.023 0.000 0.314
DI29 0.000 -1.135 0.000 0.173 0.000 -0.733
1.180 DI26 0.000 0.308 0.000 -0.023 0.000 -0.515
DI29 0.000 -1.925 0.000 0.173 0.000 1.072
3+C-D/1 0.000 DI26 0.000 0.777 0.000 -0.003 0.000 -1.164
DI29 0.000 4.128 0.000 0.070 0.000 1.332
DI31 0.000 4.189 0.000 0.071 0.000 1.315
DI32 0.000 0.716 0.000 -0.004 0.000 -1.147
0.740 DI1 0.000 2.719 0.000 0.047 0.000 -2.158
DI31 0.000 3.695 0.000 0.071 0.000 -1.602
DI32 0.000 0.221 0.000 -0.004 0.000 -1.494
3+D-F/1 0.000 DI1 0.000 -3.731 0.000 0.004 0.000 -2.456
DI10 0.000 -3.766 0.000 -0.024 0.000 -2.147
DI13 0.000 -1.615 0.000 0.031 0.000 -1.376
DI26 0.000 -4.475 0.000 -0.020 0.000 -2.315
1.080 DI10 0.000 -4.472 0.000 -0.024 0.000 2.301
DI13 0.000 -2.321 0.000 0.031 0.000 0.750
DI26 0.000 -5.181 0.000 -0.020 0.000 2.899
3+F-G/1 0.000 DI1 0.000 -11.524 0.000 0.003 0.000 -1.866
DI15 0.000 -9.971 0.000 0.019 0.000 -1.880
DI16 0.000 -6.539 0.000 -0.015 0.000 -0.792
DI31 0.000 -9.215 0.000 0.017 0.000 -1.955
0.560 DI1 0.000 -12.062 0.000 0.003 0.000 4.738
DI15 0.000 -10.338 0.000 0.019 0.000 3.807
DI16 0.000 -6.905 0.000 -0.015 0.000 2.972
3+G-J/1 0.000 DI1 0.000 0.974 0.000 0.031 0.000 0.358
DI10 0.000 0.781 0.000 0.046 0.000 0.316
DI13 0.000 0.576 0.000 -0.002 0.000 0.191
1.270 DI10 0.000 -0.050 0.000 0.046 0.000 -0.148
DI13 0.000 -0.254 0.000 -0.002 0.000 -0.014
DI26 0.000 -0.049 0.000 0.034 0.000 -0.150
DI29 0.000 -0.256 0.000 0.009 0.000 -0.012
3+J-L/1 0.000 DI1 0.000 2.505 0.000 -0.014 0.000 1.562
3.340 DI1 0.000 -1.887 0.000 -0.014 0.000 0.530
DI26 0.000 -1.455 0.000 -0.013 0.000 0.589
ECOgcW V2.18 -NORTE-74 (2) ECO- 1

Reviso:
Y
X
8 I
K
E
12
5 H
L
C
D
F 4 11
9
J 1 B 10
G
7
A
2

Reviso:
DIAGRAMA DE COLUMNAS Nivel 1
I
H
G
F
E
C 5 8
1 12
4 9
2 3 6 7 10 11

Reviso:
DATOS DE COLUMNAS

(T) (T) (T) (T*m) (T*m) (T*m)
2+A/0-1 0.000 DI3 16.485 0.035 0.157 0.045 -0.318 -0.028
DI4 35.827 0.354 1.061 -0.030 1.121 0.448
DI6 3.712 -0.172 0.193 -0.009 0.009 -0.350
DI9 48.600 0.562 1.025 0.025 0.794 0.770
DI10 11.585 -0.028 -0.018 0.044 -0.719 -0.107
DI13 40.727 0.417 1.235 -0.028 1.521 0.527
DI26 16.578 0.073 0.100 0.030 -0.743 0.063
DI29 35.734 0.317 1.118 -0.015 1.545 0.357
2.850 DI3 15.827 0.035 0.157 0.045 -0.765 -0.128
DI4 35.168 0.354 1.061 -0.030 -1.903 -0.562
DI6 3.054 -0.172 0.193 -0.009 -0.542 0.141
DI9 47.942 0.562 1.025 0.025 -2.126 -0.832
DI10 10.927 -0.028 -0.018 0.044 -0.669 -0.028
DI13 40.068 0.417 1.235 -0.028 -2.000 -0.662
2+G/0-1 0.000 DI3 -3.064 -0.006 -0.004 0.001 -0.012 -0.014
DI10 -4.990 -0.006 -0.005 0.001 -0.019 -0.015
DI13 4.917 0.004 0.007 -0.001 0.014 0.013
DI26 -5.676 -0.003 -0.005 0.001 -0.021 -0.008
DI29 5.604 0.002 0.007 0.000 0.016 0.006
2.850 DI3 -3.172 -0.006 -0.004 0.001 -0.002 0.002
DI10 -5.098 -0.006 -0.005 0.001 -0.004 0.002
DI13 4.809 0.004 0.007 -0.001 -0.006 0.001
DI16 -1.548 0.002 0.000 0.001 -0.008 0.002
DI26 -5.784 -0.003 -0.005 0.001 -0.007 0.002
DI29 5.495 0.002 0.007 0.000 -0.003 0.001
2+J/0-1 0.000 DI3 5.503 -0.013 -0.003 0.001 -0.011 -0.022
DI10 7.743 -0.013 -0.005 0.001 -0.017 -0.023
DI13 0.871 0.002 0.007 -0.001 0.013 0.011
DI26 9.995 -0.010 -0.004 0.001 -0.019 -0.015
DI29 -1.381 -0.001 0.006 0.000 0.015 0.003
2.850 DI3 5.395 -0.013 -0.003 0.001 -0.002 0.015
DI10 7.635 -0.013 -0.005 0.001 -0.004 0.015
DI13 0.762 0.002 0.007 -0.001 -0.006 0.005
DI16 7.523 -0.005 0.001 0.001 -0.008 0.013
DI26 9.887 -0.010 -0.004 0.001 -0.007 0.013
DI29 -1.490 -0.001 0.006 0.000 -0.003 0.007
2+L/0-1 0.000 DI3 -9.036 -0.609 -0.761 0.045 -1.175 -0.962
DI4 35.547 0.730 -0.201 -0.030 -0.055 1.014
DI26 3.579 -0.263 -1.285 0.030 -2.037 -0.473
DI29 22.932 0.384 0.324 -0.015 0.807 0.525
2.850 DI3 -9.695 -0.609 -0.761 0.045 0.992 0.773
DI4 34.888 0.730 -0.201 -0.030 0.517 -1.066
DI26 2.920 -0.263 -1.285 0.030 1.625 0.277
DI29 22.273 0.384 0.324 -0.015 -0.116 -0.570
3+A/0-1 0.000 DI3 28.559 -0.109 0.593 0.045 0.288 -0.164
DI4 32.646 0.149 0.842 -0.030 0.788 0.253
DI6 30.287 -0.287 0.620 -0.009 0.369 -0.458
DI9 30.918 0.327 0.815 0.025 0.707 0.547
DI26 17.892 -0.043 0.303 0.030 -0.419 -0.047
DI29 43.314 0.083 1.132 -0.015 1.495 0.136
2.850 DI1 41.338 0.027 1.002 0.011 -2.104 -0.017
DI3 27.901 -0.109 0.593 0.045 -1.403 0.146
DI4 31.988 0.149 0.842 -0.030 -1.611 -0.172
DI6 29.629 -0.287 0.620 -0.009 -1.397 0.359
DI9 30.260 0.327 0.815 0.025 -1.616 -0.386
DI29 42.655 0.083 1.132 -0.015 -1.732 -0.102
3+G/0-1 0.000 DI3 -0.179 -0.008 -0.004 0.001 -0.009 -0.017
DI10 -2.159 -0.009 -0.006 0.001 -0.016 -0.018
DI13 3.376 0.005 0.000 -0.001 0.005 0.014
DI26 -3.875 -0.006 -0.007 0.001 -0.020 -0.010
DI29 5.092 0.002 0.002 0.000 0.010 0.006
2.850 DI3 -0.287 -0.008 -0.004 0.001 0.003 0.007
DI10 -2.267 -0.009 -0.006 0.001 0.001 0.008

Reviso:
DATOS DE COLUMNAS

(T) (T) (T) (T*m) (T*m) (T*m)
DI13 3.268 0.005 0.000 -0.001 0.004 -0.001
DI26 -3.983 -0.006 -0.007 0.001 0.000 0.006
DI29 4.984 0.002 0.002 0.000 0.005 0.001
DI31 4.617 -0.002 0.001 0.000 0.006 0.003
3+J/0-1 0.000 DI3 5.110 -0.030 -0.004 0.001 -0.009 -0.039
DI10 7.526 -0.031 -0.006 0.001 -0.015 -0.041
DI13 -0.632 0.008 0.001 -0.001 0.005 0.017
DI26 9.209 -0.022 -0.008 0.001 -0.020 -0.027
DI29 -2.315 -0.001 0.002 0.000 0.010 0.003
2.850 DI3 5.002 -0.030 -0.004 0.001 0.003 0.047
DI10 7.418 -0.031 -0.006 0.001 0.003 0.048
DI13 -0.740 0.008 0.001 -0.001 0.003 -0.006
DI26 9.101 -0.022 -0.008 0.001 0.001 0.036
DI29 -2.424 -0.001 0.002 0.000 0.005 0.006
DI31 -1.640 -0.009 0.001 0.000 0.005 0.017
3+L/0-1 0.000 DI1 8.482 -0.003 -0.054 0.000 -0.057 -0.005
DI3 5.351 -0.025 -0.043 0.001 -0.048 -0.038
DI4 6.862 0.021 -0.030 -0.001 -0.030 0.031
DI26 7.899 -0.014 -0.059 0.001 -0.071 -0.021
2.850 DI1 8.344 -0.003 -0.054 0.000 0.096 0.005
DI3 5.242 -0.025 -0.043 0.001 0.075 0.034
DI4 6.753 0.021 -0.030 -0.001 0.055 -0.027
DI26 7.790 -0.014 -0.059 0.001 0.098 0.018
6+A/0-1 0.000 DI3 19.914 -0.230 1.006 0.045 0.847 -0.279
DI4 10.364 0.073 0.778 -0.030 0.610 0.182
DI6 33.787 -0.500 1.027 -0.009 0.709 -0.661
DI9 -3.509 0.343 0.757 0.025 0.748 0.564
DI15 36.361 -0.482 1.438 -0.007 1.347 -0.624
DI16 -6.083 0.325 0.346 0.023 0.110 0.527
DI31 30.068 -0.243 1.802 -0.008 2.022 -0.262
DI32 0.210 0.086 -0.018 0.024 -0.565 0.165
2.850 DI3 19.256 -0.230 1.006 0.045 -2.020 0.377
DI4 9.706 0.073 0.778 -0.030 -1.607 -0.026
DI6 33.128 -0.500 1.027 -0.009 -2.217 0.765
DI9 -4.167 0.343 0.757 0.025 -1.410 -0.414
DI15 35.703 -0.482 1.438 -0.007 -2.753 0.750
DI16 -6.741 0.325 0.346 0.023 -0.875 -0.399
DI31 29.410 -0.243 1.802 -0.008 -3.115 0.430
DI32 -0.448 0.086 -0.018 0.024 -0.512 -0.079
6+F/0-1 0.000 DI3 2.054 -0.001 -0.003 0.001 -0.005 -0.009
DI10 -1.334 -0.001 -0.007 0.001 -0.013 -0.010
DI13 3.885 0.011 -0.001 -0.001 0.001 0.019
DI26 -4.994 0.002 -0.010 0.001 -0.021 -0.002
DI29 7.545 0.008 0.002 0.000 0.009 0.011
2.850 DI1 1.647 0.007 -0.006 0.000 0.008 -0.013
DI3 1.946 -0.001 -0.003 0.001 0.005 -0.006
DI10 -1.443 -0.001 -0.007 0.001 0.007 -0.006
DI13 3.777 0.011 -0.001 -0.001 0.005 -0.012
DI22 -4.037 0.003 -0.010 0.000 0.010 -0.008
DI26 -5.102 0.002 -0.010 0.001 0.009 -0.007
DI29 7.437 0.008 0.002 0.000 0.003 -0.011
6+J/0-1 0.000 DI3 4.215 -0.017 -0.002 0.001 -0.004 -0.026
DI10 7.256 -0.018 -0.006 0.001 -0.012 -0.027
DI13 -0.081 0.011 -0.001 -0.001 0.002 0.020
DI26 9.797 -0.012 -0.010 0.001 -0.020 -0.017
DI29 -2.622 0.005 0.003 0.000 0.010 0.009
2.850 DI3 4.107 -0.017 -0.002 0.001 0.003 0.022
DI10 7.148 -0.018 -0.006 0.001 0.005 0.023
DI13 -0.190 0.011 -0.001 -0.001 0.004 -0.012
DI22 8.166 -0.004 -0.010 0.000 0.009 0.006
DI26 9.689 -0.012 -0.010 0.001 0.008 0.017
DI29 -2.731 0.005 0.003 0.000 0.001 -0.005
6+L/0-1 0.000 DI3 35.764 -0.778 -0.377 0.045 -0.440 -1.122

Reviso:
DATOS DE COLUMNAS

(T) (T) (T) (T*m) (T*m) (T*m)
DI4 -1.344 0.512 -0.302 -0.030 -0.396 0.808
DI10 43.744 -0.799 -0.872 0.044 -1.155 -1.148
DI13 -9.325 0.532 0.193 -0.028 0.319 0.833
DI26 42.231 -0.503 -1.318 0.030 -1.814 -0.699
DI29 -7.811 0.236 0.638 -0.015 0.978 0.385
2.850 DI3 35.105 -0.778 -0.377 0.045 0.634 1.096
DI4 -2.003 0.512 -0.302 -0.030 0.466 -0.650
DI10 43.086 -0.799 -0.872 0.044 1.330 1.129
DI13 -9.983 0.532 0.193 -0.028 -0.230 -0.683
DI26 41.572 -0.503 -1.318 0.030 1.941 0.734
DI29 -8.469 0.236 0.638 -0.015 -0.841 -0.289

Reviso:
DISEO DE COLUMNA C-1

DATOS (EJE 1-D, PLANTA BAJA)
P= = 43.09 Ton
M(BA)b= = 1.33 T.m DIRECCION X-X
M(AB)b= = 1.13 T.m
Vu= = 0.80 Ton
M(BA)b= = -1.16 T.m DIRECCION Y-Y
M(AB)b= = -1.15 T.m
CONCRETO CLASE= 1
f'c= 250 Kg/cm2
f*c= 213 Kg/cm2
f''c= 170 Kg/cm2
fy= 4200 Kg/cm2
fs= 1680 Kg/cm2
Est#= 3 = 0.71 cm2
= 0.95 cm
Es= 2000000 Kg/cm2
Ec= 11000 f'c = 11000 250 = 173925.3 Kg/cm2
Hcol= 2.85 m
LTRA-1= 5.12 m
direccion x
LTRA-2= 0.00 m
LTRA-1= 3.07
direccion y
LTRA-2= 0.00
rx= 8 cm
ry= 8 cm
FR= 0.8 FLEXOCOMPRESION
RESTRIICION LATERAL = 1
CONSIDERANDO LOS EFECTOS DE ESBELTES SENTIDO X-X
trabe= 25 X 50 cm
espesor de losa= 10 cm
e= 4t= 4 X 10 = 40 cm 105
e= h-t= 50 - 10 = 40 cm 10
se toma la menor por lo tanto e= 40 cm
e
centroide = 10 x 105 x 25 = Y= 12.8 cm 40 50 cm
25 x 40 + 105 x 10
Momento de inercia centroidal=

I = I + Ad 2 25
3 2 3 2
Itrab= 105 x 10 + 105 x 10 x 12.20 + 25 x 40 + 25 x 40 x 12.8
12 12
4
I= 462,205.28 cm
Momento de inercia de la columna

columna = 30 x 45 cm
45 cm
bxh3
=
3 4
ICOL= 30 x 45 = 227812.5 cm
12 12
30 cm
Reviso:
CALCULO DE RIGIDECES
PARA EL NUDO A TENEMOS A= 0.0 POR TRATARSE DE UN EMPOTRAMIENTO
PARA EL NUDO B TENEMOS

I T 1 1,805 cm
3
RIGIDES DEL SISTEMA DE PISO
K T 1 = = 462,205.28 = sentido x-x
LT 1 256 + 0
3
I 462,205.28 = 3,011 cm sentido y-y
K T 2 = T 2 = 154 + 0
LT 2
I C 1
K C 1 = =
RIGIDES DE LA COLUMNA LC 1
I C 1 cm3
K C 1 = = 227812.5 = 969 68678 = 79.48843
LC 1 235 864
B= KCOL = 969 + 79 = 0.22

KTRABES 1,805 + 3,011
CALCULO DE LAS LONGITUDES EFECTIVAS DE PANDEO

CON EL NOMOGRAMA CON RESTRICCION LATERAL A= 0.00 B= 0.22 K= 0.69
LONGITUD EFECTIVA DE PANDEO= kLcol= 235 x 0.69 = 162 cm
VERIFICACION DE ESBELTEZ=
a)RADIO DE GIRO=0.30xH= 0.30 x 45 = 13.50 cm
b) RELACION DE ESBELTEZ= Kl/r= 162.15 = 12 < 100 como 12 < 44.2

13.50 no es necesario revisar los efectos de esbeltez
M
c) valor maximo=
34 12 1b = 34 - 12 1.13 = 44.2
M 2b 1.33
CALCULO DE MOMENTOS AMPLIFICADOS
Mc = Fab M 2
M1
Cm = 0.6 + 0.4 = 0.6 + 0.4 1.1 = 0.939549
M2 1.33
2E I
Pc = 2
= 2 x 10,565,960,232 =
2
104,276,758,800.15 = 3,966 ton
(kL ) 162 26292.62
0.4 EcIg 10,565,960,232 Kg-cm

2
EI = = 0.4 x 173,925 x 227812.5 = 15,848,940,348 =
1+ u 1 + 0.5 1.5
Ec= 11000 250 = 173,925 Kg/cm2

Reviso:
U= 0.5
Cm 0.94 = 0.95
Fab = = 1 - 43
Pu
1 0.75 x 3,966
0.75 PC
Mc= 1.00 1.33 = 1.33 ton (Momento de diseo)
CONSIDERANDO LOS EFECTOS DE ESBELTEZ SENTIDO Y-Y
Momento de inercia de la columna

45 cm
bxh3
=
3
ICOL= 45 x 30 = 101250 cm4
12 12
CALCULO DE RIGIDECES 30 cm
PARA EL NUDO A TENEMOS A= 0.0 POR TRATARSE DE UN EMPOTRAMIENTO
PARA EL NUDO B TENEMOS

I T 1 1,805 cm
3
RIGIDES DEL SISTEMA DE PISO
K T 1 = = 462,205.28 = sentido x-x
LT 1 256 + 0
3
I 462,205.28 = 3,011 cm sentido y-y
K T 2 = T 2 = 154 + 0
LT 2
RIGIDES DE LA COLUMNA
I C 1 cm3
K C 1 = = 101250 = 431
LC 1 235
B= KCOL = 431 + 36 = 0.10

KTRABES 1,805 + 3,011
CALCULO DE LAS LONGITUDES EFECTIVAS DE PANDEO

CON EL NOMOGRAMA CON RESTRICCION LATERAL A= 0.00 B= 0.10 K= 0.66
LONGITUD EFECTIVA DE PANDEO= kLcol= 235 x 0.66 = 155 cm
VERIFICACION DE ESBELTEZ=
a)RADIO DE GIRO=0.30xH= 0.30 x 45 = 13.50 cm
b) RELACION DE ESBELTEZ= Kl/r= 155.10 = 11 < 100 como 11 < 46

13.50 no es necesario revisar los efectos de esbeltez
M
c) valor maximo=
34 12 1b = 34 - 12 1.15 = 45.93
M 2b 1.16
CALCULO DE MOMENTOS AMPLIFICADOS
Mc = Fab M 2
Reviso:
M1
Cm = 0.6 + 0.4 = 0.6 + 0.4 -1.1 = 1.006732
M2 -1.1
2E I
Pc = 2
= 2 x 4,695,982,325 =
2
46,345,226,133.40 = 1,927 ton
(kL ) 155 24056.01
0.4 EcIg 4,695,982,325 Kg-cm

2
EI = = 0.4 x 173,925 x 101250 = 7,043,973,488 =
1+ u 1 + 0.5 1.5
Ec= 11000 250 = 173,925 Kg/cm2
U= 0.5
Cm 1.01 = 1.04
Fab = = 1 - 43
Pu
1 0.75 x 1,927
0.75 PC
Mc= 1.00 x 1.2 1.16 ton (Momento de diseo)
DISEO DE LA COLUMNA CON EL METODO DE BRESLER
1
PR =
1 1 1
+
PRX PRY PRO
SUPONIENDO UN PORCENTAJE DE ACERO DEL = 1.3 % SE TIENE LO SIGUIENTE
As= 30 x 45 x 0.013 = 17.55 cm2 CON V's# 5 = 17.55 = 8.86 V's# 5

SE DEJARAN 10 V's# 5 = 10 x 1.98 = 19.8 cm2 1.98
diametro de la barra mas delgada= 1.59 cm
3 V's# EN EL SENTIDO X-X
4 V's# EN EL SENTIDO Y-Y
CALCULO DE Po= PRO = Ag (0.18 f ' c + 0.40 fy0.024) =

PRO= 1350 x ( 0.18 X 250 + 0.4 x 4200 x 0.024 )= 115182.00 kg
PRO= 115.18 Ton
Reviso:
OBTENEMOS LA CARGA NORMAL RESISTENTE DE DISEO Pr CON EXCENTRICIDAD EN AMBAS DIRECCIONES
ex= Mux = 1.33 = 0.03 m

Pu 43
ey= Muy = 1.16 = 0.03 m

Pu 43
CALCULO DE ESFUERZOS INTERNOS SENTIDO X-X
kd fc despejando dfc
por comparacion de triangulos calculamos kd, tenemos = kd =
d fs fs
fc + fc +
donde 2n 2n
n= Es = 2000000 = 11.50 kd= 22 x 74.375 = 11.10 cm
Ec 173925.3 74.375 + 1680
d= 22 cm 2 x 11.50
en condiciones de servicio el concreto no excedera del 35%
2
fc= 0.35 x 250 x 0.85 = 74.375 Kg/cm k= 11.10 0.50
22
f cs kd d ' f c (kd d ' )

= despejando f cs =
fc kd kd
fcs= 74.375 x 11.10 - 8 = 20.77 Kg/cm2

11.10
fsc= 2nfcsfs = 2 x 11.50 x 20.77 = 478 1680
CALCULO DE ESFUERZOS INTERNOS SENTIDO Y-Y
dy= 37 kd= 37 x 74.4 = 18.67 k= 18.67 = 0.50

74.375 + 1680 37
2 x 11.50
Reviso:
fcs= 74.375 x 18.67 - 8 = 42.50 Kg/cm2

18.67
fsc= 2nfcsfs = 2 x 11.50 x 42.50 = 977 1680
3 cm 3 cm
MOMENTOS CON RESPECTO AL EJE NEUTRO SENTIDO X-X
MRX= Cc x 7.40 + Cs x 3.10 + T 10.90
donde
Cc= 1 fcbkd 7.40 = 1 x 74.38 x 45 x 11.10 x 7.40 = 137430.6 Kg.cm
2 2
Cs= 3 V's# A's fsc= 3 x 1.98 x 478 x 3.10 = 8791.487 Kg.cm
T= 3 V's# A's fs= 3 x 1.98 x 1680 x 10.90 = 108783.6 Kg.cm
por lo tanto MRX= 137430.6 + 8791.487 + 108783.6 = 255005.7 Kg.cm
por lo tanto la carga normal resistente de diseo con una excentricidad en sentido X-X vale
PRX= 255005.7 = 82,610 Kg = 82.61 Ton

3
MOMENTOS CON RESPECTO AL EJE NEUTRO SENTIDO Y-Y
MRX= Cc x 12.44 + Cs x 10.67 + T 18.33
donde
Cc= 1 fchkd 12.44 = 1 x 74.38 x 45 x 18.67 x 12.44 = 388724.2 Kg.cm
2 2
Reviso:
Cs= 4 V's# A's fsc= 4 x 1.98 x 977 x 10.67 = 82570.96 Kg.cm
T= 4 V's# A's fs= 4 x 1.98 x 1680 x 18.33 = 243938.9 Kg.cm
por lo tanto MRX= 388724.2 + 82570.96 + 243938.9 = 715234.1 Kg.cm
por lo tanto la carga normal resistente de diseo con una excentricidad en sentido X-X vale
PRY= 715234.1 = 266,810 Kg = 266.81 Ton

3
aplicando la ecuacion de bresler se tiene 1
PR =
1 1 1
+
PRX PRY PRO
PR= 1 = 139.45 > 43 se acepta

1 + 1 - 1
82.61 266.81 115.18
PR
la ecuacion de bresler sera valida si 0.10 139.45 > 0.1 1.210682 > 0.1 SE ACEPTA
PRO 115.18
CUANDO NO SE CUMPLA LA ECUACION ANTERIOR SE PUEDE UTILIZAR LA SIGUIENTE EXPRESION
M UX M 133000 + -115500 = 0.52 + -0.161486 = 0.36 < 1

+ UY 1.00 255005.7 715234.1
M RX M RY
cuando se cumpla se aplicaran lo siguiente terminos
Agf 'c
a)
PU > 43 > 1350 x 250 = 43 > 33.75 SI CUMPLE
10 10
b) lado menor de la columna > 30cm 30 < 30 nocumple
c) area de concreto no menor que Pu/0.5f'c 43086 = 345 < 1350 SI CUMPLE
0.5 x 250
d) la relacion entre lados de la columna no sera menor que 0.4 30 = 0.67 > 0.4 SI CUMPLE
45
e) la relacion entre la altura libre de la columna y lado menor no sera mayor de 15
285 = 9.5 < 15 SI CUMPLE
30
REVISION DE LA COLUMNA POR CORTANTE
En miembros a flexocompresion en los que el valor absoluto de la fuerza axial de diseo Pu, no exceda de
FR (0.7 f ' cAg + 2000 As = 0.8 ( 0.7 x 213 x 1350 + 2000 x 19.8 = 192330
192 Ton > 43 Ton SI CUMPLE
cuantia de acero en la cara de compresion minima P= 5.94 = 0.004 < 0.015

1350
Reviso:
VCR = FR bd (0.2 + 20 p f *c = ecuacion 2.19 NTCC
Vcr= 0.8 x 30 x 45 x ( 0.2 + 20 x 0.004 x 213 = 4534.148 Kg
VCR = 0.5 FR bd f *c = ecuacion 2.20 NTCC

Vcr= 0.5 x 0.8 x 30 x 45 x 213 = 7871.785 Kg
se tomara el valor de Vcr= 4534.148 Kg ecuacion 2.19 de las NTCC
Pu
se bera de multiplicar por el valor de la siguiente ecuacion 1 + 0.007 = 1 + 0.007 43 = 1.000223
Ag 1350
el valor de Vcr= 4534.148 x 1.000223 = 4535.16 Kg
cortante ultimo Vu= 800.00 Kg
separacion de estribos
FrAvfyd
a) por fuerza cortante
S= = 0.8 x 1.42 x 4200 x 22 = -28 cm
Vu Vcr 800 - 4535
b) 850/fy veces el diametro de la barra mas delgada = 850 = 13.12 x 1.59 = 20.9 cm
4200
c) 48 diametros de la barra de estribo 48 x 0.95 = 45.6 cm
d) la mitad de la dimension menor de la columna = 30 = 15 cm
2
la separacion de estribos es = 20 cm
la separacion se reducira a la mitad en los extremos en una longitud no menor que:
a) la dimension transversal maxima de la columna= 45 cm
b) un sexto de su altura = 2.85 = 47.5 cm

6
c) 60 cm

Vigueta y Bovedilla

Cargado por

Copyright:

Formatos disponibles

Vigueta y Bovedilla

Cargado por

Información del documento

Descripción original:

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

Vigueta y Bovedilla

Cargado por

Copyright:

Formatos disponibles

SMG INGENIERIA DE DISEO ESTRUCTURAL

MEMORIA DE CALCULO ESTRUCTURAL

REVICION DE LAS CONDICIONES DE REGULARIDAD SEGN LAS NTC DEL DF-2004

2.- La relacin de su altura a la dimensin menor de su base no pasa de 2.50 SI CUMPLE

3.- La relacin de largo a ancho de la base no excede de 2.50 SI CUMPLE

11.- En ningn entrepiso la excentricidad torsional, calculada estticamente se excede

Ing. Salvador Melchor Cruz Sp.07/11

DATOS ANLISIS SISMICO

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 1

Ing. Salvador Melchor Cruz Sp.07/11

ANLISIS SSMICO DINMICO [RDF2004]

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 2

Ing. Salvador Melchor Cruz Sp.07/11

Fuerzas ssmicas equivalentes

REVISION POR CARGA VERTICAL

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 4

Ing. Salvador Melchor Cruz Sp.07/11

Ing. Salvador Melchor Cruz Sp.07/11

REVISION POR CARGA LATERAL

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 6

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 7

Ing. Salvador Melchor Cruz Sp.07/11

REVISION POR MOMENTO DE VOLTEO

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 8

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 9

Ing. Salvador Melchor Cruz Sp.07/11

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 11

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 12

Ing. Salvador Melchor Cruz Sp.07/11

Ing. Salvador Melchor Cruz Sp.07/11

ANEMgcW V3.08 NORTE 74 (2) -NORTE 74 (2 ANEM)- 14

NORTE 74 (2) -NORTE 74 (2 ANEM)-

NORTE 74 (2) -NORTE 74 (2 ANEM)-

NORTE 74 (2) -NORTE 74 (2 ANEM)-

NORTE 74 (2) -NORTE 74 (2 ANEM)-

NORTE 74 (2) -NORTE 74 (2 ANEM)-

CALCULO DE CENTRO DE CARGAS EN PLANTA BAJA

COORDENADAS DE CADA FIGURA

FIGURA CALCULO DE AREAS

PESO DEL EDIFICIO

AREA DE LA CIMENTACION 121.98 m2

CALCULO DE CENTRO DE CARGAS EN CIMENTACION

M xpb + M xcim + 7.74 m

PESO TOTAL= 947.79 Ton (CON FACTOR DE 1.4) MODULO DE SECCION EN X=

ESFUERZOS EN EL TERRENO POR CARGA GRAVITACIONAL

MOMENTO EN X= W x ex= 947.79 x 0.09 = 89.4613 ton.m

W M X MY 947.79 89.4613 143.635

qn= 7.77 0.49 0.44

q1= 8.70 Ton/m2

q2= 7.82 Ton/m2

q4= 6.84 Ton/m2

REVISION DE LA CIMENTACION POR SISMO

CON SISMO EN DIRECCION X CON SISMO EN DIRECCION Y

qnx= 5.55 4.72 0.80 qnx= 5.55 1.42 2.66