Joaquin Cuenca Abela

** INDUSTRY SAFETY ALERT ** Summary: While rolling out air and water hoses across an AFC installation, a fitter was asked to connect a 50 mm air hose to a manifold before the hose was rolled out. The fitter removed a retaining staple to connect into a 50 mm airline supply. The end cap ejected, hitting the fitter in the leg just below the kneecap. The fitter was unaware that the line was pressurised. Recommendations to industry: Mine operators should have procedures in place to prevent exposing workers to the hazards of stored energy. Mine operators should ensure workers are trained on these procedures, and that all workers are aware of the status of stored energy sources. Source: NSW Resources Regulator - Weekly Incident Summary - Week ending 5 July 2024 #incident #safety #underground #longwall

5

Safety Alert: Unplanned lift descent What happened: On 21 September 2024, a near miss was reported due to an unplanned descent of a lift on a gantry crane. Following external engineers using the lift, internal engineers called the lift to the fourth level. Once it had reached the platform and the external gate had opened, the lift slowly descended away from the gate leaving an open edge. The internal engineers then isolated the lift. The external engineers had accidentally knocked the latch securing the emergency ladder inside the lift car. The shuddering of the lift ascending had caused the ladder to be released completely from the latch (image 1), falling forwards and making contact with the emergency brake release (image 2) which is designed to the allow the lift to descend in situations where power is lost, and personnel are stuck inside. For the full alert: https://lnkd.in/e57sUVqV #safety #cargohandling

2

Diagnose fuel fault on Weidemann Loadall #ClaphamAg #Weidemann #Loadall #MachineryRepair #Repair

3

Planet Engineering, Qatar Technical Blogs Restore the reliability and efficiency of your diesel engines performance with a comprehensive engine overhaul and genuine engine parts. https://lnkd.in/gSnqdP8m

1

🚀 Firehorn’s Recovery System Update💥 The Firehorn team has completed another development test on the Recovery sub-system, this time focusing on the line cutter. In this test, the cutter successfully sliced through a Dyneema rope—much stronger than what we plan to use—using just 0.5g of black powder. The line cutter is a critical component in the parachute’s two-stage deployment system. Initially, the parachute opens partially, held in place by a reefing line. Once the cutter severs the line, the parachute expands to its full size, enabling a controlled descent. This test, although not involving the final design or flight hardware, demonstrates the team’s ability to experiment with various ideas during the development phase. By working with robust materials like Dyneema, we can assess whether our designs are on the right track before moving forward with a finalized version. As always, safety protocols were followed closely throughout the test. We'll continue refining this and other subsystems in the coming months, stay tuned!🚀✨ Main Sponsors: APCO Technologies SA | EPFL | Constellium Gold Sponsors: Kistler Group | maxon | 3D PRECISION SA | Schoeller-Bleckmann Oilfield Technology (SBOT) | Swagelok Switzerland | ARBOR Fluidtec AG #RocketDevelopment #LineCutterTest #EngineeringProcess #FirehornRocket #RecoverySystem #SubsystemTesting #SpaceTech #EPFLRocketTeam

37

3 comentarios

Standardizing the layout and design of an ambulance module can save your organization money and help boost personnel efficiency. Knowing where to find equipment in every unit in a large fleet speeds up response times. ❔ What's 1 item you must have on every ambulance to help you do your job to the best of your ability? Tell us in the comments! #CrestlineAmbulances #CCL150 #Ambulance #FleetManagement #NewAmbulance #EMS #EmergencyMedicalServices #EmergencyVehicles

1

Its Tech Tip Tuesday! When making a VULKAN LOKRING Connection, the Sealed System Servicer must ensure that they have evenly distributed LOKPREP around the outer diameter of the tube of they will be inserting into the connection. This can be accomplished by rotating the body of the connector 360° after applying LOKPREP to the tube end. More information on proper application of LOKPREP can be found on the '00 Series LOKRING Knowledge Base' where you can view our Catalog, Distributor List, and Training Materials! The Knowledge base can be accessed by following this link 💻 https://lnkd.in/ew9UuZ7N Please also visit our YouTube Channel 📲 https://lnkd.in/eDmZuG6U for Training Videos. #LokInYourEducation #Training #AmericanVULKAN #LOKRING #AVC #LOKRING #VULKANLOKRING #SealedSystems #Refrigeration #lokprep #WeEnsureThatSystemsWorkBetter #givebrazingtheboot

35

More choice. More control. Meet OCPP. zappi is now OCPP supported as standard. myenergi https://ow.ly/CNfj50Rf5Ao

2

Can you be sure that all spares parts in your engineering stores are working in tip-top condition? When an equipment breakdown strikes, you want to get your machine back up and running in as little time as possible… But it’s in these situations where complacency may set in. If your machine breakdowns due to faulty automation hardware, you may have a spare unit in your engineering stores which could save the day. 😀 However, we have heard countless stories where the faulty part is accidentally put back into stores and left to gather dust until the next breakdown strikes …. only this time, the spare part that you were relying on won’t be much help. 😩 Accidents happen, it’s human nature. But the last thing you want to find out in a breakdown situation is that the spare part you had in engineering stores is also faulty. That is why the product testing service that we offer could save your engineers a serious headache when your next breakdown strikes. 👨‍🏭 We call fully test your spare inventory to make sure that it’s in tip top condition and, to save you any doubt, we will repackage your kit in sealed boxes with clear labelling that states the relevant product details as well as the testing date so that your stores managers have total peace of mind. Just another way it pays to work with a TRUE Technical Automation distributor. Not sure about the condition of your spare kit? Jump on the link below and fill in our short technical support form and we will call you to talk you through your options 👍 https://lnkd.in/eySUrKg7 #IndustrialAutomation #IndustrialEngineering #Downtime

3

🔥গরমে থাকুন কুল, যদি থাকে DeepCool ১ম কমেন্ট দেখুন 🛑 Key Features ✔️ Model: AK400 ✔️ Matrix fin design ✔️ High-performance cooling with low noise ✔️ 03-year warranty ✔️ Bearing Type - Fluid Dynamic Bearing #dclcomputer #dcl #daffodilcomputer #daffodil #daffodilpc #dcllaptop #digimarktanvir #DigitALL #Trending #viral #foryou #foryoupage

3

1 comentario