| Magnetic measurements of the 5 meter QC series quadrupoles at Lawrence Berkeley Laboratory (p. 439) |
| by Barale, P J |
| Overview of the superconducting magnet subsystem for the GEM detector at the SSC (p. 795) |
| by Deis, G |
| Measurement and alignment goals for the SDC detector (p. 889) |
| by Hovde, R J |
| Design of tunnel cooling system |
| by Cheng, A |
| A study of the effect of cable insulation on coil properties |
| by Spindel, A |
| Development of hermetic electrical connectors for SSC spool pieces |
| by Koutanis, B |
| A study of variations in dipole cable insulation systems and their effect on creep |
| by Sims, R E |
| Design of an 80 K liner prototype in SSCL ASST for synchrotron light interception |
| by Shu, Q S |
| Test of Fermilab built, post-ASST, 50-mm-aperture, full length SSC dipole magnets |
| by Kuzminski, J |
| Extracted strand I$_{c}$ and strand I$_{c}$ degradation for SSC cables |
| by Kovachev, V |
| Results of cabling from phase 1B of the SSC vendor qualification program |
| by Coleman, E S |
| Systematic error analysis of rotating coil using computer simulation |
| by Li, W C |
| Building the repositories to serve |
| by De Lynden, L |
| SSC 50 mm dipole magnet cryostat thermal measurement results |
| by Boroski, W N |
| Experimental Young's modulus calculations |
| by Chen, Y |
| Summary of dipole field angle measurements on 50 mm-aperture SSC collider dipole magnet prototypes |
| by Marks, J |
| Operating modes of the SSC sector station cryogenic system |
| by Ganni, V |
| Statistical factors to qualify the superconducting magnets for the SSC based on warm/cold correlations |
| by Kim, K |
| Effective stress of a 4.2 K beam tube in a quenching collider 50 mm dipole magnet for the SSC |
| by Leung, K K |
| Design of a model dipole magnet for the SSC high energy booster |
| by Hassan, N |
| Conductor design for the GEM detector magnet |
| by Minervini, J V |
| Beam instrumentation and precision timing equipment for the SSC accelerator complex |
| by Webber, R C |
| Low power rf beam control electronics for the LEB |
| by Mestha, L K |
| Preliminary results from a study of collar lamination variation in SSC prototype dipole magnets |
| by Gattu, R |
| An engineering design study of the support platform assembly for the SSC SDC detector |
| by Krebs, H |
| The accelerator systems string test : objectives, problems, results, anecdotes, and reflections |
| by Dombeck, T W |
| Stress analysis on SSC cryogenic shaft transfer line suspension system |
| by Zhang, B |
| Data acquisition and controls for the SSCL ASST phase I |
| by Bork, R G |
| Cryogenic characteristics of the SSC accelerator systems string test (ASST) |
| by Burgett, W S |
| The Accelerator Systems String Test cryogenics |
| by Mulholland, G T |
| Heat leak measurements and thermal modeling of a mechanical support for a SSC beam tube liner |
| by Maddocks, J |
| The thermal behavior of an SSC magnet in an unconditioned outdoor environment |
| by Pletzer, R |
| Engineered design of SSC cooling ponds |
| by Bear, J |
| Initial results of strand produced in phase II of the SSCL vendor qualification program |
| by Erdmann, M |
| System-level description of the SDC detector |
| by Wells, N |
| FDDI experience at the SSCL |
| by Jaffe, M |
| Facility modeling of West Utility straight tunnel section |
| by Butalla, M W |
| A systems approach to hazard and risk management for the SDC detector |
| by Lavelle R |
| A quench detection/logging system for the SSCL magnet test laboratory |
| by Kim, K |
| A methodology to describe process control requirements |
| by Carcagno, R |
| Industrial harmonic analysis system for magnetic measurements of SSC collider arc and high energy booster corrector magnets |
| by Green, M I |
| Minimum recommended SSC laboratory seismic design requirements |
| by Western, J L |
| Design and performance of a new 50 mm quadrupole magnet for the SSC |
| by Spigo, G |
| Mechanical analysis of the DSB cross-section |
| by Chen, Y |
| Reducing the energy requirements of quench protection heaters for SSC dipoles : test results |
| by Haddock, C |
| Comparisons of processes and performance of SSC-VQP material |
| by Seuntjens, J M |
| Dynamic analysis of six-strut supporting system for accelerator magnet |
| by Leung, K K |
| A quasi-3D model to predict temperature distribution in SSC magnets due to 3D heat loads |
| by Archer, B |
| Electrical performance characteristics of the SSC accelerator system string test |
| by Robinson, W |
| Equipment acquisition plans for the SSCL magnet excitation power systems |
| by Winje, R A |
| An engineering design study of the transfer bridge for the SSC SDC detector |
| by Western, J L |
| SDC muon barrel toroid 1/9.197 scale test model at SSC |
| by Tseng, C W J |
| Current loop decay in Rutherford-type cables |
| by Akhmedov, A I |
| An engineering design study of alternative design options for the forward toroids of the SSC SDC detector |
| by Dittert, L I |
| Optical measurement of SSC arc quadrupole cold mass location |
| by Corbett, C |
| Test performance of the QSE series of 5 cm aperture quadrupole model magnets |
| by Archer, B |
| Method of fabricating a completely ordered wound coil |
| by Mookerjee, S |
| Off-line analysis software for the Texas Test Rig |
| by Yost, G P |
| Technical status of SSC rf amplifier and accelerating cavity systems |
| by Ferrell, J |
| Three-dimensional model of a liquid-cooled, Low Energy Booster, radio-frequency cavity tuner at the Superconducting Super Collider |
| by Ranganathan, R |
| A study of structural integrity of the SSC magnet six-strut support system |
| by Chang, C |
| Conceptual design studies for a He II cooled low beta quad IR magnets |
| by Baritchi, D |
| Conceptual design of the cryostat system for the 2 : 1 vertical bending dipole magnet of the SSC collider ring |
| by Jalloh, A R |
| Databases for analysis of superconducting cable manufacturing |
| by Bardos, V A |
| Experimental strength verification of SSC cryogenic transfer line internal suspension system |
| by Stifle, K |
| Structural and thermal analysis of a solid-cooled, Low Energy Booster, radio-frequency-cavity tuner at the Superconducting Super Collider |
| by Ranganathan, R |
| Structural behavior of the six-strut support system |
| by Dao, B |
| Low Energy Booster radio frequency cavity structural analysis |
| by Jones, K |
| The design and development of a single piece, sandwich tube coldmass support post for the SSC collider dipole magnets |
| by Ahmad, A |
| Design and analysis of the collider SPXA/SPRA spool piece vacuum barrier |
| by Cruse, G |
| Thermal analysis of the SSC beam scraper |
| by Tran, N K |
| Parameters and conceptual design of a vertical bending magnet for the Super Collider |
| by Goodzeit, C L |
| Designing, fabricating, and testing cost effective structural composite for the SSCL magnets |
| by Nobrega, F |
| Development of cryogenic instruments and equipment for SSC magnet cryogenic tests at the MTL |
| by Shu, Q S |
| Effective stress of a 4.2 K beam tube in a quenching collider 50 mm dipole magnet for the SSC |
| by Leung, K K |
| Fabrication and as-built design of the 50 mm aperture SSC model quadrupole magnets |
| by Hassan, N |
| The application of moving average control charts for evaluating magnetic field quality on an individual magnet basis |
| by Pollock, D A |
| Cold test facility for 1.8 m superconducting model magnets at the SSCL |
| by Labarge, A |
| The proposed vacuum system for the interaction regions of the Superconducting Super Collider |
| by Chapman, G R |
| Magnetic design considerations for the SSC vertical bending (BV1C) magnet |
| by Venkatraman, V |
| Multilayer insulation for the interconnect region in the accelerator system string test : a practical engineering approach for a new scheme of design and installation bridges |
| by Baritchi, D |
| An experimental evaluation of joint electrical resistance on power lead thermal performance |
| by Datskov, V I |
| Systems analysis determining critical items, critical assembly processes, primary failure modes and corrective actions on ASST magnets |
| by Arden, C S |
| A study on sector nitrogen inventory emergency venting |
| by Zhang, B |
| Preliminary design of sector cryogenic shaft transfer line system |
| by Zhang, B |
| Business opportunities in the SSCL global control system |
| by Heefner, J W |
| Supplier performance evaluation and rating system (SPEARS) |
| by Oged, M |
| Collider quadrupole magnet (CQM) optical alignment window heat leak prediction |
| by Pletzer, R K |
| Low conductivity water plants : issues of process control |
| by Baritchi, L |
| An engineering study and concept design of the supervisory control and data acquisition (SCADA) for conventional systems |
| by Norman, L S |
| Laboratory technical services provides business opportunities for supervisory control and data acquisition systems |
| by Ballard, W P |
| Strain gauge pack in process measurement system for the collider quadrupole, design and technology transfer |
| by Zeigler, R E |
| The accelerator systems string test program |
| by Kraushaar, P |
| Design and analysis of the cryostat system for a 15 m long prototype quadrupole magnet |
| by Jalloh, A R |