S PM058

INSTRUCTION
MANUAL FOR

RUGER® 10/22®
AUTOLOADING RIFLES

10/22 Takedown®

10/22® Carbine

10/22® Tactical

10/22® Target LITE

– Rugged, Reliable Firearms® –

READ THE INSTRUCTIONS AND
WARNINGS IN THIS MANUAL CAREFULLY
BEFORE USING THIS FIREARM
© 2024 Sturm, Ruger & Co., Inc.
This manual may not be reproduced in whole or in part without the express written
permission of Sturm, Ruger & Co., Inc.
For Service on This Model Please Call:
(336) 949-5200 (See p. 37)
THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BE
TRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED
OR PRESENTED TO ANOTHER PERSON

Ruger.com
B 1/2024 R38
 State-By-State Warnings
Certain states require by law that their own specified warning notices
in larger-than-normal type be conspicuously included by the
manufacturer, distributor or retailer with firearms sold in that state.
Sturm, Ruger & Co., Inc. sells its products in compliance with
applicable laws and regulations. Because our products may be sold in
these states, we include the following:
California:
WARNING
“Firearms must be handled responsibly and securely stored to prevent
access by children and other unauthorized users. California has strict
laws pertaining to firearms, and you may be fined or imprisoned if you
fail to comply with them. Visit the Web site of the California Attorney
General at https://oag.ca.gov/firearms for information on firearm laws
applicable to you and how you can comply.
Prevent child access by always keeping guns locked away and unloaded
when not in use. If you keep a loaded firearm where a child obtains and
improperly uses it, you may be fined or sent to prison.
If you or someone you know is contemplating suicide, please call the
national suicide prevention lifeline at 1-800-273-TALK (8255).”

ADVERTENCIA
“Las armas de fuego deben manipularse de manera responsable y segura
para evitar el acceso de niños y otros usuarios no autorizados. California
tiene leyes estrictas relacionadas con armas de fuego, y usted puede ser
multado o encarcelado si no las cumple. Visite el sitio web del
Procurador General de California en https://oag.ca.gov/firearms para
obtener información sobre las leyes de armas de fuego que le son
aplicables y cómo puede cumplirlas.
A los niños los atraen las armas de fuego y las pueden hacer funcionar.
Ellos pueden causarses lesions graves y la muerte. Evite que los niños
tengan accesso a las armas de fuego guardándolas siempre con llave y
descargadas cuando no las esté utilizando. Si usted tiene un arma de
fuego cargada en un lugar en que un niño tiene acceso a ella y la usa
indebidamente, le pueden dar una multa o enviarlo a la carcel.
Si usted o alguien que conoce está pensando en suicidarse, llame a la
línea nacional de prevención del suicidio al 1-800-273-TALK (8255).”

3
Connecticut:
“UNLAWFUL STORAGE OF A LOADED FIREARM MAY
RESULT IN IMPRISONMENT OR FINE.”

Florida:
“IT IS UNLAWFUL, AND PUNISHABLE BY
IMPRISONMENT AND FINE, FOR ANY ADULT TO
STORE OR LEAVE A FIREARM IN ANY PLACE WITHIN
THE REACH OR EASY ACCESS OF A MINOR UNDER 18
YEARS OF AGE OR TO KNOWINGLY SELL OR
OTHERWISE TRANSFER OWNERSHIP OR POSSESSION
OF A FIREARM TO A MINOR OR A PERSON OF
UNSOUND MIND.”

Maine:
“ENDANGERING THE WELFARE OF A CHILD IS A
CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION
WITHIN EASY ACCESS OF A CHILD, YOU MAY BE
SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP
FIREARMS AND AMMUNITION SEPARATE. KEEP
FIREARMS AND AMMUNITION LOCKED UP. USE
TRIGGER LOCKS.”

Maryland:
“WARNING: Children can operate firearms which may cause
death or serious injury. It is a crime to store or leave a loaded
firearm in any location where an individual knew or should
have known that an unsupervised minor would gain access to
the firearm. Store your firearm responsibly!”

4
Massachusetts:
“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM,
RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE
UNLESS THAT WEAPON IS EQUIPPED WITH A
TAMPER-RESISTANT SAFETY DEVICE OR IS STORED
OR KEPT IN A SECURELY LOCKED CONTAINER.”

New Jersey:
“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED
FIREARM WITHIN EASY ACCESS OF A MINOR.”

New York:
“THE USE OF A LOCKING DEVICE OR SAFETY LOCK
IS ONLY ONE ASPECT OF RESPONSIBLE FIREARM
STORAGE. FOR INCREASED SAFETY, FIREARMS
SHOULD BE STORED UNLOADED AND LOCKED IN A
LOCATION THAT IS BOTH SEPARATE FROM THEIR
AMMUNITION AND INACCESSIBLE TO CHILDREN
AND UNAUTHORIZED PERSONS.”

North Carolina:
“IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM
THAT CAN BE DISCHARGED IN A MANNER THAT A
REASONABLE PERSON SHOULD KNOW IS
ACCESSIBLE TO A MINOR.”

5
Texas:
“IT IS UNLAWFUL TO STORE, TRANSPORT, OR
ABANDON AN UNSECURED FIREARM IN A PLACE
WHERE CHILDREN ARE LIKELY TO BE AND CAN
OBTAIN ACCESS TO THE FIREARM.”

Wisconsin:
“IF YOU LEAVE A LOADED FIREARM WITHIN THE
REACH OR EASY ACCESS OF A CHILD YOU MAY BE
FINED OR IMPRISONED OR BOTH IF THE CHILD
IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS
THE FIREARM.”

* * * * * * * * * * * * * * * * * * * * * *

Please check with your licensed retailer or state police for

additional warnings which may be required by local law or
regulation. Such regulations change constantly, and local
authorities are in the best position to advise you on such legal
matters.

6
 FIREARMS SAFETY IS YOUR RESPONSIBILITY
SAFETY MUST BE THE FIRST AND CONSTANT
CONSIDERATION OF EVERY PERSON WHO HANDLES
FIREARMS AND AMMUNITION.

This instruction manual is designed to assist you in learning how to use

and care for your RUGER® 10/22® rifles properly. Please contact us if
you have any questions.
Only when you are certain you fully understand the manual and can
properly carry out its instructions should you practice loading, unloading,
etc. with live ammunition. If you have any doubts about your ability to
handle or use a particular type of firearm safely, you should seek
supervised instruction. Such personalized instruction often is available
from local firearm retailers, gun clubs or police departments. If none of
these sources can help visit nra.org or write to the following address:

National Rifle Association

11250 Waples Mill Road
Fairfax, VA 22030-7400

The person possessing a firearm has a full-time job. You cannot guess; You
cannot forget; You must know how to use your firearm safely. Do not use
any firearm without having a complete understanding of its particular
characteristics and safe use. Remember: There is no such thing as a
foolproof firearm.

7
 TABLE OF CONTENTS
Page
State-By-State Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Locking Device Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Operation of Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
The Bolt Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
10/22 Takedown® Barrel Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Special Safety Note - 10/22® Target Rifle Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Loading the Magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
To Load and Fire (With Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To Load and Fire (Without Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
To Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
To Extract and Eject a Chambered Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
To Clear a Malfunction (“Jam” or “Misfire”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
To Minimize Malfunctions (“Jams” or “Misfires”) . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Check Your Rifle’s Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Magazine Inspection and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Maintenance of Stainless Steel Rifles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Attaching Scope Base Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Service and Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Shipping Firearms for Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 - 44
10/22 Takedown® Supplemental Parts List & Exploded View . . . . . . . . . . . . . .44 & 45
The Basic Rules of Safe Firearms Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
“RUGER” and “10/22” are registered U.S. trademarks.

WARNINGS OF GREAT IMPORTANCE ARE

FOUND ON THE FOLLOWING PAGES:
Locking Devices 10 Unloading 24
Alterations 13 Bore Obstructions 26
Manual Safety 16 Malfunctions 28
Lead Exposure 19 Disassembly 28
Ammunition 19 Lubrication 34
“Stinger” Ammunition 20 Storage 34
Target Trigger 20 Shipping 37
Firing 23 Parts Purchasers 38
Handling 23

OTHER CAUTIONS AND WARNINGS APPEAR

THROUGHOUT THE MANUAL.
8
All models have the same basic operation mechanism and include the following
features with which the firearm user should be thoroughly familiar.

Please Note: Some 10/22® Rifles do not have a barrel band.

NOMENCLATURE
(10/22® Carbine Model Shown)

Receiver Bolt Rear Sight Front Sight

Barrel
Trigger Guard Barrel Band
Stock (housing)

Safety Cocking Handle

Trigger (shown “on”)

Magazine
Bolt Lock Take-Down
Magazine Release Screw

Figure 1. In these illustrations the frequently used operating components are identified.
Note that the safety is protruding fully from the right side of the trigger guard and is
therefore in its “on” (safe) position.

9
 LOCKING DEVICE
INSTALLATION INSTRUCTIONS

WARNING – USE OF LOCKING DEVICES

• Always keep your firearm pointed in a safe direction,
including when you are installing or removing your
locking device.
• Always verify that your firearm is completely unloaded
before installing your locking device.
• Do not install locking devices in the trigger guard;
always keep your fingers and locking device outside the
trigger guard during device installation and removal.
• Store firearms, ammunition and keys separately and
securely, away from children and careless adults; do not
store your firearm with the keys in the locking device.
• Do not attempt to work the action of your firearm with
the locking device in place; this may damage your
firearm.
• While locking devices are an important aid to security
measures, they are not a substitute for safe firearm
handling and proper storage. Remember that any
Do not store keys mechanical device can be bypassed with enough time,
in lock. knowledge, determination and equipment.

LOCKING DEVICES MUST BE USED

SAFELY AND RESPONSIBLY

It is important to use the locking device on your Ruger® firearm when

the firearm is stored or immediate use is not planned.
Keep the muzzle pointed in a safe direction and your fingers outside the
trigger guard at all times!
To Install the Factory-Supplied Locking Device:
1. Remove the magazine.
2. Be sure the firearm and its magazine are completely unloaded and
contain no cartridges or cartridge cases!

10
3. Open the action completely. Use the bolt lock to keep the action open
during installation of the locking device.
4. Insert the free end of the cable into the ejection port as shown in
Figure 2.
5. Pull the cable through the Figure 2
magazine well as shown in
Figure 2.
6. Insert the free end of the cable
into the lock. (See Figure 3.)
7. To lock: With the key turned to
the farthest clockwise position,
insert the loose end of the cable
into the lock. Turn the key
counterclockwise and remove it
from the lock.
8. Once the lock is securely Figure 3
closed, pull firmly on the lock
to test the connection and be
sure it is locked. Do not leave
or store your firearm with the
key in the lock! Store your
locked unloaded firearm and
the key in secure, separate
locations, away from
ammunition, children, and
unauthorized adults.

Correct installation of the lock

on a Ruger® 10/22® rifle.

11
To Install the Factory-Supplied Locking Device on the Ruger®
10/22 Takedown® Rifles:
It is important to use the locking device on your Ruger® firearm when
the firearm is stored or immediate use is not planned.
Keep the muzzle pointed in a safe direction and your fingers outside the
trigger guard at all times!
1. Remove the magazine. Be sure the firearm and its magazine are
completely unloaded and contain no cartridges or cartridge cases!
2. Open the action completely. Use the bolt lock to keep the action open
during installation of the locking device.
3. Insert the cable directly into your rifle as shown in Figure 4.
4. To lock: With the key turned to the farthest clockwise position, insert
the loose end of the cable into the lock. Turn the key
counterclockwise and remove the key.
5. Once the lock is securely closed, pull firmly on the lock to test the
connection and be sure it is locked. Do not leave or store your
firearm with the key in the lock! Store your locked unloaded firearm
and the key in secure, separate locations, away from ammunition,
children, and unauthorized adults.

Figure 4

Correct installation of the lock on a Ruger® 10/22 Takedown® rifle.

12
 FIREARMS ARE DANGEROUS WEAPONS.
READ THE INSTRUCTIONS AND WARNINGS IN THIS
MANUAL THOROUGHLY AND CAREFULLY BEFORE USE.

WARNING - ALTERATIONS
This product was designed to function
properly in its original condition.
Alterations can make it unsafe. Do not
alter any part or add or substitute parts or
accessories not made or sold by Sturm,
Ruger & Co., Inc.

DO NOT ALTER ANY FIREARM

GENERAL INFORMATION
AND MECHANICAL CHARACTERISTICS
The RUGER® 10/22® rifles are autoloading, recoil operated rifles.
Retracting the cocking handle cocks the internal hammer and compresses the
recoil spring. When the bolt is manually released, it moves forward (driven by
the recoil spring), strips a cartridge from the magazine, if a loaded magazine is
in place, and chambers the cartridge. The bolt is held against the chambered
cartridge by the recoil spring.
When the trigger is pulled, the hammer is released and strikes the firing pin. The
firing pin indents the cartridge case rim and ignites the priming compound
inside the rim. This ignites the powder in the cartridge case and a great volume
of gas is instantly generated, which acts on the interior of the cartridge case in
all directions.
Because the bullet offers the least resistance, it moves out of the cartridge case
and exits the muzzle. The bolt then moves rearward automatically, extracting
and ejecting the fired cartridge case, and at the same time cocking the hammer
and compressing the recoil spring, etc., as described above. Once the trigger is
released, the rifle is ready to fire again.
Each time the trigger is pulled and released, the same cycle is repeated until
there are no more cartridges in the magazine or in the chamber.
The rifle will fire if there is a cartridge in the chamber and the trigger is pulled,
whether or not there is a magazine in place! Removing the magazine does not
unload the rifle. Never assume the rifle is unloaded. Visually inspect the chamber
and the magazine each time the rifle is handled to be certain there are no
cartridges in either.

13
The 10/22® Carbine is identified by its curved carbine-style butt plate and
barrel band. The Deluxe Sporter Model has a flat recoil pad, cut
checkered stock, and no barrel band. The Target Model has a heavyweight,
hammer forged barrel, laminated target style stock, and a special target trigger
(see p. 20). The All-Weather® Model has a carbine style stock with barrel
band and is checkered on the forearm, pistol grip and butt plate. The black
composite stock is made of a thermoplastic polyester resin, reinforced with
fiberglass for strength, durability, and resistance to the elements. These models
use a ten-shot rotary magazine chambered for the 22 Long Rifle cartridge
The 10/22® RIFLE features a slimmer, hardwood stock, longer barrel, flat rifle
butt plate, ramp front sight, and no barrel band. It uses the same ten-shot rotary
magazine, chambered for the 22 Long Rifle cartridge, as the 10/22® Carbine
models.
The 10/22® Compact Rifle features a shorter barrel, shorter rifle-style,
hardwood stock and forend, flat buttplate, and fiber optic front and rear sights.
Chambered for the 22 Long Rifle Rimfire cartridge, the Compact Rifle uses the
same ten-shot rotary magazine as the 10/22® Carbine.
The 10/22® Tactical Rifle features a Mini-14®-style flash suppressor. This
threaded barrel version allows owners to attach an assortment of muzzle
accessories. It also features a black synthetic stock, and a precision-rifled, cold
hammer-forged 16-1/8” alloy steel barrel with black matte finish. This model
uses the same ten-shot rotary magazine as the 10/22® Carbine.
The Ruger® 10/22 Takedown® Rifle features an easy takedown for
quick separation of the barrel from the action for ease of transportation and
storage. Simple reassembly allows for a secure connection of the barrel and
action and returns the firearm to zero, even when receiver mounted optics are
used, ensuring consistent accuracy. See page 17 for “Barrel Assembly
Instructions.” This model uses the same ten-shot rotary magazine as the 10/22®
Carbine.

14
 OPERATION OF SAFETY
The RUGER® 10/22® rifles and carbines have a cross-button safety which is
located in the forward portion of the trigger guard (See Figure 1, p. 9.) The safety
can be operated only when the hammer is cocked.
The safety is “on” when it protrudes fully from the right side (the cocking handle
side) of the trigger guard assembly, as shown in Figure 1. In this position the
sear is blocked, and the firearm cannot be fired from a normal pull on the
trigger.
The safety should always be in the “on” (safe) position except when the shooter is
actually firing the firearm. The safety should be moved to the “on” position
whenever the shooter ceases firing, even temporarily.
The safety is “off” (fire) when it protrudes from the left side of the trigger guard
assembly, as shown in Figure 5. When the safety is off, the red band shows on the
safety button. Do not totally rely on the appearance of the red band to indicate
that the safety is off. In poor light or if dirt is present, the red band may not be
visible. If the safety is “off” and the trigger is pulled, the rifle will fire.

SAFETY IN “OFF” (FIRE) POSITION

Figure 5. The underside of the trigger guard section of the rifle. In this illustration the
safety is shown in the “off” (fire) position. The position of the safety and red band indicate
the safety is “off.” It should be in this position only when you are actually firing at a target.

The safety is held in its “on” or “off” position by a plunger that is under spring
tension. When the safety is moved to either the “on” or “off” position, a distinct
“click” should be heard. Frequently check the position of the safety to be certain
the safety has not been inadvertently moved. If the safety seems to move too
easily, or if the click is not heard when the safety is moved, stop using the rifle
and return it to the Newport Customer Service Department for repair (see p. 37).

15
 WARNING – MANUAL SAFETY
Keep the safety on unless actually firing.
Always move the safety fully to its intended
position and check it. The safety is not “ON”
SAFETY IN “ON” (SAFE) POSITION unless it is completely “ON”. Never depend on
a safety mechanism or any other mechanical
device to justify careless handling or
permitting the rifle to point in an unsafe
direction. The only “safe” rifle is one in which
the bolt is open, the chamber is empty, and
there is no magazine in the firearm.

KNOW HOW TO USE THE SAFETY

THE BOLT LOCK

The bolt lock is located in the forward section of the trigger guard (see Figure 1,
p. 9). The bolt lock is the manually operated means of retaining the bolt in the
rearward (open) position. When the bolt is locked open, the rifle is in an
inoperative safe condition for inspection of the chamber, cleaning, etc.

To lock the bolt open: Retract the cocking handle to its extreme rearward
position and, while holding it there, press in on the lower section of the bolt
lock. Release pressure on the cocking handle and it will move forward a fraction
of an inch, and then be locked in its open position.

Press Back to Lock Bolt Open Press Up to Close Bolt

To release the bolt: Retract the cocking handle to its extreme rearward position
and then press in on the upper section of the bolt lock. Release the bolt and it
will move fully forward.

NOTE: Simply retracting the bolt will not disengage the lock. The bolt lock
must be deliberately pressed up while the bolt is held fully to the rear. Only then
will the bolt close when released. This is designed to prevent accidental release of
the bolt from its open position.

16
 RUGER® 10/22 TAKEDOWN®
Barrel Assembly Instructions

The RUGER® 10/22 TAKEDOWN® rifle has an adjustable lock-up

mechanism. The following directions describe the adjustment necessary to
ensure proper lockup the first time the barrel is installed. After the first
adjustment, the barrel may be installed by following steps 1 and 3 only, and the
barrel may be removed by following steps 1 and 5 only.
1. Remove the magazine, lock the bolt open (see page 16), and verify the rifle is
unloaded by visually inspecting the chamber.
2. Loosen the adjustment knob by turning it clockwise as far as possible with
finger pressure. (See Figures 6a & 6b.)
Adjustment Knob

Loosen

Tighten
Figure 6a Figure 6b

INSTALLING THE BARREL ASSEMBLY

3. Install the barrel assembly by:

1 inserting it into the receiver

(see Figure 7), and
1 Insert Barrel

Figure 7

2 rotating it clockwise until it

Rotate Barrel
locks into place. (See Figure 8.) 2 Clockwise to
Lock in Place

Figure 8

17
4. Tighten the adjustment knob by turning it counterclockwise as far as possible
with finger pressure.
5. To remove the barrel assembly, 1 lock the bolt back and 2 push the locking
lever towards the muzzle. Next, 3 rotate the barrel assembly counterclockwise
and 4 pull the barrel assembly out of the receiver. (See Figure 9.)

REMOVING THE BARREL ASSEMBLY

1 Lock Bolt Back

3 Rotate the Barrel Assembly

Counterclockwise

2 Push the Locking

Lever Forward to
Unlock Barrel
4 Remove Barrel
Figure 9 Assembly from Receiver

6. Tighten the adjustment knob by rotating it counterclockwise one or two (1 - 2)

more clicks.
7. Reinstall the barrel assembly. You should feel some resistance when turning
the barrel assembly, but it should not be difficult. If further adjustment is
needed, remove the barrel assembly and “tighten” or “loosen” the adjustment
knob accordingly.
NOTE: Following barrel installation, best fired shot accuracy will be achieved if the
action is dry cycled prior to actually firing ammunition in the rifle: Remove the
magazine from the rifle and be certain the chamber is empty. Keeping the rifle
pointed in a safe direction, pull the cocking handle fully to the rear while holding
the bolt lock up, then release the cocking handle, letting it “slingshot” (freely fly
forward) into the ready-to-fire position. Repeat 2 - 3 times. This will properly “seat”
the barrel assembly.

18
 AMMUNITION
The RUGER® 10/22® CARBINE and 10/22® Rifles are chambered for, and
designed to properly function with, only the 22 caliber Long Rifle rimfire cartridge,
standard, high velocity, or hyper-velocity, manufactured to U.S. industry standards.
Do not use 22 short, 22 long, 22 shot, or 22 cartridges loaded with blunt-nosed,
sharp-shouldered, or “explosive” bullets. They will not function reliably and may jam
the mechanism or discharge before being fully chambered. Use only ammunition that
functions correctly in your rifle. See “Warning – Malfunctions,” p. 28.

WARNING - LEAD EXPOSURE

Discharging firearms in poorly
ventilated areas, cleaning firearms, or
handling ammunition may result in
exposure to lead and other substances
known to the State of California to
cause birth defects, reproductive harm,
and other serious physical injury. Have
adequate ventilation at all times. Wash
hands thoroughly after exposure.

SHOOTING OR CLEANING FIREARMS

MAY EXPOSE YOU TO LEAD

WARNING – AMMUNITION
Use only new, factory ammunition of
the correct caliber.
Death, serious injury, and damage can
result from the wrong ammunition,
bore obstructions, powder overloads or
incorrect cartridge components. 22
cases are very thin and sometimes split
when fired.
Always wear shooting glasses and
hearing protection.
IMPROPER AMMUNITION
DESTROYS FIREARMS

AMMUNITION (CARTRIDGES) NOTICE

WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE
OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR
AS A RESULT OF, THE USE IN ANY RUGER FIREARMS OF FAULTY
OR NON-STANDARD OR “REMANUFACTURED” OR HAND-LOADED
(RELOADED) AMMUNITION OR OF CARTRIDGES OTHER THAN THOSE
FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.

19
NOTE: The following warning applies to RUGER® 10/22® Target and
Tactical rifles only:

WARNING – “STINGER” AMMUNITION

“Stinger” cartridges have a longer case
than 22 LR cartridges loaded to U.S.
Industry specifications. They can stick
in the tighter chambers of target rifles,
including the Ruger® 10/22® Target and
.22
S Tactical rifles, which can result in a
T
I
N
hazardous ruptured case and release of
22 LR
G
E
hot powder gasses and brass when fired.
R

DO NOT USE “STINGER”

22 LR 22 "Stinger"
AMMUNITION IN 10/22®
TARGET or TACTICAL RIFLES

SPECIAL SAFETY NOTE

®
10/22 TARGET RIFLE ONLY
The special model you have selected is specifically designed for rapid fire precision
target shooting. As such, it demands that you take extra safety precautions.
The trigger of the Target version of the RUGER® 10/22® has a lighter, target
trigger pull than standard 10/22® rifles and carbines, for more precise placement of
shots. You should practice “dry-firing” an empty rifle (with it pointing in a safe
direction) to learn the “feel” of the trigger before ever loading it with ammunition.

WARNING – TARGET TRIGGER

10/22® Target models have a target trigger
that has been carefully set at the factory to a
minimum safe weight of pull for precision
target shooting. Do not alter any factory
setting! You can create an unsafe condition
and the rifle may fire unexpectedly.
You should be especially careful to keep the
safety on at all times except when actually
SAFETY IN “ON” (SAFE) POSITION
firing and keep your finger off the trigger
unless you are squeezing it to fire, in order
to minimize the possibility of accidental
discharge.

DO NOT TAMPER WITH TRIGGER -

KEEP SAFETY ON UNLESS FIRING

20
 MAGAZINE
The 9-shot 22 WMR magazine (JMX-1) for the Ruger® 10/22® Magnum is longer
than the 10-shot 22 long rifle magazine (BX-1) for Ruger® 10/22® rifles. Do not
attempt to use standard 10/22 magazines in the 10/22® Magnum rifles or load 22
short, long, or long rifle ammunition into the 22 magnum. They will not
function correctly and are unsafe to use in 22 magnum rifles.
Ruger 10/22® Magnum Ruger 10/22® Long Rifle Magazine
Magazine (JMX-1) (BX-1)

Do Not Use in Ruger® 10/22® Magnum

Never attempt to use 22 Long Rifle ammunition in Ruger® 10/22® Magnum rifle
magazines. The cartridges have a smaller case diameter and can split or burst
when fired in the larger magnum chamber, releasing hot powder gasses and
particle fragments out of the action at high speed, possibly resulting in injury to
the shooter or bystanders.

LOADING THE MAGAZINE

Loading
Magazine
To load the magazine, press the rim of the
cartridge against the magazine rotor at the
widest section of the magazine throat until
the cartridge enters far enough to be
pushed to the rear end of the magazine.
Each succeeding cartridge is pressed against
the body of the top cartridge and slid to the
rear of the magazine until a maximum of
ten (10) 22 LR cartridges are in the
magazine.

21
 TO LOAD AND FIRE (WITH MAGAZINE)
Practice this important aspect of firearm handling (with an unloaded rifle) until you
can perform each of the steps – described below – with skill and confidence. But before
you do anything with the rifle, please first read completely through this manual.
1. Keep the muzzle pointed in a safe direction. (See Rule 2, p. 46.)
2. Pull the cocking handle rearward. Engage the bolt lock so that the bolt is held open.
(See p. 16.) Check the chamber to be certain it is empty. Engage the safety. (See
Figure 1, p. 9.)

10A 10B
Figure 10. The safety should be “on” when the magazine is being removed or inserted. Move the
magazine release forward (Figure 10A) and draw the magazine out by grasping it between your
thumb and forefinger and draw it out of the firearm (Figure 10B).

3. Remove the magazine by using your index finger to push forward on the magazine
release (Figure 10A) and at the same time grasp the magazine between thumb and
forefinger of the other hand to draw it out of the magazine well. (See Figure 10B.)
4. Load the magazine with the appropriate number of cartridges (see “Loading The
Magazine” section, p. 21).
5. Insert magazine into the firearm, with bullet end of the cartridges toward the muzzle.
(Magazine cannot be seated if reversed.)
6. Load a cartridge into the chamber by fully retracting the cocking handle, releasing the
bolt lock, and then releasing the cocking handle. Don’t touch the trigger. Do not ‘ride’
the cocking handle as it moves forward. Do not apply force to the cocking handle to
chamber a cartridge. If a cartridge does not readily chamber, eject it from the rifle,
lock the bolt open, remove the magazine and see “Warning – Malfunctions”, p. 28.
7. The rifle is now fully loaded. If the rifle is not to be fired immediately, the safety should
remain “ON”. (See Figure 1, p. 9.) When the safety is moved to the “off” position, the
rifle will fire each time the trigger is pulled until all the cartridges in the magazine,
and the one in the chamber, have been fired. Firing will automatically reload and
recock the rifle. Note that every time the trigger is pulled, if a cartridge is in the
chamber, the rifle will fire – be careful!
8. Immediately following the firing of a shot, and if a subsequent shot is not to be fired at
once, put the safety “ON” while the rifle is still pointing in a safe direction down range.

22
 The safety should be moved to the “on” position as soon as firing is completed,
and it should be “on” at all times except when the rifle is on target and being
fired.
9. The bolt does not remain open after the last shot has been fired, nor does the
bolt automatically lock open when the magazine is empty. When firing is
completed, manually retract the bolt, lock it open, and visually check the
chamber to be sure it is empty. If the bolt is shut, the shooter should always
assume that there is a cartridge in the chamber. Don’t rely on your memory to
know if a firearm or magazine is loaded. Visually inspect the magazine and the
chamber.

WARNING – FIRING
The bolt automatically opens
and shuts quickly while firing.
Keep face and hands away
from it. Hot brass and powder
gas are ejected quickly and
can burn you. The rifle should
be fired from the right
shoulder. Always wear
shooting glasses and hearing
protection.

BOLT OPENS FAST–

HOT BRASS EJECTED

WARNING – HANDLING
If dropped or struck
with the safety “off”,
the rifle may fire. Keep
SAFETY IN
“OFF” POSITION
chamber empty unless
actually firing! Keep
safety “on” unless
actually firing!

ANY FIREARM
MAY FIRE IF
DROPPED
23
TO LOAD AND FIRE (WITHOUT MAGAZINE)
The rifle can be used as a single-shot rifle in the absence of a magazine or for
safety or training purposes. To do so, follow steps 1 through 3, p. 22. Next,
carefully place a single cartridge into the chamber. The chamber can be accessed
either through the magazine well or ejection port. Retract the cocking handle,
release the bolt lock, and then release the cocking handle. The rifle is now
loaded. Follow the additional instructions beginning at Step 7 on p. 22.

WARNING – UNLOADING
So that the rifle can be used as a single
loader, it will fire whether or not a
magazine is in the firearm if a cartridge is
chambered. Removing magazine does not
unload rifle! To unload, first remove
magazine, then pull bolt to rear, eject
chambered cartridge, and visually inspect
chamber. The safety should always be in
the “on” (safe) position when loading or
unloading the rifle. Keep safety “on”.

FIREARM WILL FIRE

WITH MAGAZINE OUT

TO UNLOAD
(Rifle Must Be Kept Pointed In A Safe Direction)
UNLOAD THE RIFLE IMMEDIATELY WHEN YOU ARE FINISHED SHOOTING!
NOTE: This sequence must be followed exactly as spelled out. Failure to do so
can result in the rifle’s chamber becoming unintentionally loaded with a
cartridge!
1. Keep the muzzle pointed in a safe direction at all times and keep fingers
outside the trigger guard. If the rifle is cocked, move the safety to the “on”
position.
2. Remove the magazine. Remember that even though the magazine has been
removed, a cartridge remaining in the chamber can still be fired!
3. Retract the bolt to its open position and lock it there. This should eject any
cartridge in the chamber, but...
4. Always visually double check the chamber to be certain it is empty.
5. The only “safe” rifle is one in which the bolt is open and the chamber and
magazine are empty.

24
6. Cartridges can be removed from the magazine by simply pushing them lightly
downward and forward with the thumb, forefinger, or the rubber eraser end of
a pencil against the rim of the top cartridge. Do not use a loaded cartridge as a
‘tool’ to strip cartridges from the magazine.
7. If desired, the bolt can be left in the open position, being held there by the bolt
lock. If it is desired to close the bolt, again look to be certain the chamber is
empty. Put the safety “on”, retract the bolt to its rearmost position, release the
bolt lock and let the bolt snap forward. Keep your fingers out of the receiver!
8. With the muzzle pointed in a safe direction, push the safety to the “off”
position and pull the trigger to decock it. The rifle can be “dry fired” for
practice as long as it is empty and pointed in a safe direction.
9. Push empty (unloaded) magazine into the rifle until the catch locks it in place.

CORRECT UNLOADING SEQUENCE

1
SAFETY “ON” 2

TO EXTRACT AND EJECT

A CHAMBERED CARTRIDGE
When the rifle is fired, the same gas pressure which drives the bullet forward also
acts through the cartridge case to push the bolt to the rear. That action causes
extraction and ejection of the fired cartridge case. But, when the bolt is operated
by hand, there can be a failure to extract the cartridge from the chamber, or a
failure to eject the cartridge clear of the rifle. These failures usually are the result
of the bolt not being pulled rearward vigorously, coupled with an accumulation
of bullet lubricant in the chamber. From the foregoing it is clear that the firearm
user must:
25
1. Always visually check the chamber after opening the bolt to eject a chambered
cartridge. If the bolt is not vigorously retracted when being operated by hand,
the extracted cartridge can be ‘ejected’ into the magazine area, instead of
outside the rifle.
2. Thoroughly clean the chamber and the extractor as often as necessary to
prevent the accumulation of grease and dirt.
3. If an empty magazine is in the rifle when the bolt is being hand retracted to
extract a cartridge, the cartridge may drop on top of the magazine. Then when
the bolt goes forward, the cartridge will be chambered again! Always remove
the magazine before clearing the chamber, and visually ensure that no
cartridges remain in the firearm.

WARNING –BORE OBSTRUCTIONS

Before loading or shooting your Ruger® 10/22®, be
certain the bore is unobstructed. Firing the rifle
with any obstruction in the bore may result in
severe damage to the rifle and serious injury to the
shooter and other persons nearby.
A MISFIRE or unusual report (sound) upon firing is
always a signal to cease firing immediately. After
waiting for one minute, remove the magazine, lock
the bolt open, and ensure that the chamber is
empty. It is not sufficient to only examine the
chamber in these instances. You must be certain the
bore is free from obstructions. In some firearms, it
will not be possible to easily make a determination
by simply looking. In such cases, you should use a
rod to confirm the bore is free of obstructions.
Failure to detect and correctly remove a bore
obstruction can result in serious injury to the
shooter and bystanders, and damage to the firearms.

DO NOT “SHOOT OUT”

A BORE OBSTRUCTION

TO CLEAR A MALFUNCTION
(“JAM” or “MISFIRE”)
1. Be certain the muzzle is pointed in a safe direction and the safety is “on.”
2. If the misfire is the result of a cartridge not firing or unusual report (either
louder or quieter than normal), keep the rifle pointed in a safe direction for
30 seconds prior to ejecting the chambered round or retracting the bolt.
3. If possible, first remove the magazine. It may be necessary to manually
remove a jammed cartridge which has only partially been stripped from the
magazine. If so, use extreme care. Lock the bolt open with the bolt stop
before attempting to clear the jam. Drawing the bolt fully to the rear may
bring the jammed cartridge along.

26
 Keep your face away from the ejection port during this operation. When
attempting to clear a jam, use only wood ‘tools’ so that a cartridge will not be
ignited if you strike a primer, and so that the chamber and magazine will not
be damaged. A 3/16” wood dowel rod with a point on one end is useful.
4. Visually check to make sure all cartridges have been removed from the rifle.
Safely dispose of any cartridges involved in a malfunction incident. Do not
use damaged ammunition in any firearm.
5. Using a cleaning rod, inspect the bore and chamber to ensure that they are
not obstructed. Failure to detect and correctly remove a bore obstruction can
result in serious injury!

TO MINIMIZE MALFUNCTIONS
(“JAMS” or “MISFIRES”)
Most malfunctions are caused by improper or damaged magazines, incorrect
ammunition, or poor maintenance.
1. If it appears that the firearm and magazine are not at fault and that the jam
was caused by the type of cartridge being used, then try another type.
2. If changing to another type or brand of cartridges does not at once eliminate
malfunctioning, then the following steps should be taken:
a. Make certain the firearm and the magazine are unloaded and that the safety
is “on.” Remember, the magazine should be removed first, then check the
chamber and be certain it and the magazine-well are clear of cartridges.
b. Thoroughly clean the magazine (See “Magazine Inspection and Care,” p. 32)
and bolt mechanism, paying particular attention to removing
accumulated grease. Use a bristle brush and solvent to remove grease and
fouling from the bolt face, the extractor, the chamber, and the feed ramp.
(See the “Care and Cleaning” section of this manual for detailed cleaning
instructions.)
c. Check to see that the magazine rotor spring tension is adequate.
d. Check the magazine throat to be certain they are free of nicks and burrs and
are not deformed.
e. Remove excess oil and solvent from all cleaned components, load the
magazine, and try the firearm again. As always, proceed slowly. Be certain
bystanders are not close and that you are wearing eye and hearing
protection and that your face is a safe distance from the rifle so that any
discharge resulting from a jammed cartridge will not injure anyone.
If the above procedures do not result in a smooth and reliably functioning
firearm, don’t use the firearm. The rifle can be returned directly to our Newport,
New Hampshire Customer Service Department for repair. See the Service and
Parts Policy section (p. 37) of this manual for packing and shipping information.
Another precaution: When using any firearm chambered for rimfire cartridges,
form the habit of examining fired cartridge cases. If they have bulged heads or
frequently show splits on any part of the case, the rifle or pistol should be
returned to the factory for inspection.
27
WARNING – MALFUNCTIONS
The 22 Long Rifle rimfire cartridges fire when the
firing pin impacts the relatively soft cartridge case
rim, and also can be “discharged” before it is
chambered if its rim receives a sharp blow. If a
cartridge hangs up, jams, or binds when being
chambered or when being fed from the magazine
into the chamber, do not attempt to force it into
the chamber by pushing or striking the bolt. Any
jam or feeding problem is a signal to immediately
stop using the firearm until it can be determined
what is wrong. Most failures of a cartridge to feed
or to chamber are caused by a damaged magazine,
improper firearm handling, poor maintenance,
improper or defective ammunition. Whatever the
cause, rimfire cartridge jams can result in the
potentially very dangerous situation of a cartridge
discharging before it is chambered. If this occurs,
the cartridge case will rupture and its fragments
will fly out of the firearm with sufficient force to
cause injury. Always wear shooting glasses and
hearing protectors! Keep face away from chamber!

CRUSHING RIM CAN BURST AMMO

WARNING – DISASSEMBLY

4
Always unload a firearm
before cleaning, lubrication,
3 disassembly, or assembly.

1
SAFETY “ON” 2 UNLOAD BEFORE
CLEANING

28
 DISASSEMBLY
Be Sure Rifle Is Unloaded!

An on-line video demonstrating the disassembly and reassembly of the 10/22®

rifles can be viewed by going to Ruger.com/TechTips.
1. With the rifle pointing in a safe direction, remove the magazine, open the bolt
and visually make certain there is not a cartridge in the chamber. Then allow
the bolt to close. The rear sight leaf should be down, and the hammer should
be cocked.
2. Loosen the barrel band screw and remove the barrel band. (Does not apply to
non-barrel band models such as the Sporter and Rifle Model.)
3. Use an appropriate size Allen wrench to loosen (don’t remove) the take-down
screw.
4. Position the safety so an equal amount of the button is exposed on each side. If
the safety is not in the middle when the barrel-receiver assembly is lifted out
of the stock, the stock will be damaged.
5. Swing the barrel-receiver assembly upward away from the forearm of the
stock. Be careful the two receiver cross pins and bolt stop pin do not fall out.
6. Place the safety in the “ON” position. Remove the trigger guard by simply
drifting out the two receiver pins. It is recommended that the components of
the trigger guard assembly not be disassembled from the trigger guard.
This is the extent of disassembly required for routine inspection, cleaning and
lubrication.
If it is desired to thoroughly clean the inside of the receiver by removing the
bolt, be aware that although removing and installing the bolt (along with the
cocking handle-recoil spring assembly) is simple, it must be done correctly.
7. To remove the bolt:
a. Position the rifle upside down so the bolt is fully accessible.
b. Drift out the bolt stop pin, located at the rear of the receiver.
c. Pull the cocking handle fully to the rear of the receiver with the left hand,
and while it is in that position, using the right hand, lift up the front of
the bolt until it is disengaged from the cocking handle.
d. Remove the cocking handle assembly through the ejection port.
e. Lift bolt out of receiver. If it does not come out readily, turn the rifle over
and the bolt will drop out of the receiver.

29
 REASSEMBLY
Again, Be Sure Rifle is Unloaded!

1. Reassembly of bolt into receiver:

a. To reassemble cocking handle and bolt in the receiver, position the rear
end (cone pointed) of the recoil spring guide rod in the mating recess
near the rear right side of the receiver. The recoil spring must be flat
against the side and “bottom” of the receiver.
b. Maintain the guide rod in its proper position by keeping pressure on the
cocking handle with the left forefinger and thumb. At the same time, use
the flat side of the screwdriver blade to compress the recoil spring by
drawing it against that area of the cocking handle near to the spring. In
accomplishing this spring compression it is necessary to maintain the same
pressure on the screwdriver with the right hand as that being maintained
(rearward and inward) on the cocking handle with the left hand.
c. When the spring is fully compressed, maintain it in that position with the
left hand and with the right hand lay the recessed section of the top of
the bolt on the section of the cocking handle that mates with it. Press down
on the bolt until a ‘click’ is heard. At this point allow the cocking handle
(with bolt attached) to move forward slowly.
d. Cycle the cocking handle a few times to be certain the components are
correctly assembled.
2. Reassembly of rifle:
a. Install the bolt stop pin and then lay the trigger guard in place and install
the two receiver pins. NOTE: Be sure the ejector is held in the ejector
slot as you set the trigger guard in place (see Figure 11).
b. Assemble the barrel-receiver to the stock by following, in reverse order,
steps 1 through 5 under the “Disassembly” instructions on page 29.
Firearms should not be stored loaded or cocked!
Figure 11

Ejector
Slot

Ejector

30
 CHECK YOUR RIFLE’S FUNCTION
Periodic inspection of any firearm is important to ensuring its safe operation. It is
important to clean and inspect your firearm after each range session or whenever the
firearm has been exposed to sand, dust, moisture, humidity, or other adverse
conditions. Proper maintenance increases the longevity of your firearm and will allow
early detection of worn or broken parts.
Prior to each use, visually inspect the firearm to ensure no components are damaged,
missing, loose, bent, cracked, chipped, or peened. If you observe excessive wear, you
should stop using your rifle and contact customer service or a trained, certified
gunsmith to evaluate its condition and replace any worn parts, if necessary.
After any disassembly and reassembly, it is important to verify that the action is
working correctly before any live firing is attempted.
FIRST, BE SURE THERE IS NO AMMUNITION IN THE CHAMBER OR THE
MAGAZINE AND KEEP THE RIFLE POINTED IN A SAFE DIRECTION!
a. CHECK THE BOLT FUNCTION: Pull the bolt fully to the rear and release it. The bolt
should operate smoothly and travel freely within the receiver without binding.
Repeat this process two more times.
b. CHECK THE SAFETY FUNCTION: NOTE: When the safety is moved to either the “on” or
“off” position, a distinct “click” should be heard. If the safety seems to move too
easily, or if the click is not heard when the safety is moved, stop using the rifle and
contact Ruger Customer Service at 336-949-5200. For additional information
regarding the safety, please refer to the “Operation of Safety” section of this
manual.
• First, pull the bolt fully to the rear and release it. This should cock the
hammer. Do not dry fire the rifle.
• Next, engage the safety by pushing it into the “on” position and attempt to pull
the trigger. With the safety in this position, the trigger should not move and
the hammer should not fall.
• Finally, move the safety to the “off” position. With the rifle pointed in a safe
direction, pull the trigger and listen for an audible “click” as an indication the
hammer has fallen, striking the firing pin.
Repeat this process two more times.
c. CHECK THE BOLT LOCK FUNCTION:
• First, retract the cocking handle to its extreme rearward position and, while
holding it there, press in on the lower section of the bolt lock.
• Next, release pressure on the cocking handle. The bolt should move forward a
fraction of an inch, and then be locked in its open position.
• Finally, retract the cocking handle to its extreme rearward position and then
press in on the upper section of the bolt lock. Release the bolt and it should
move fully forward.

An on-line video demonstrating the disassembly, reassembly, and function check of

the RUGER® 10/22® can be viewed by going to Ruger.com/TechTips.
If any of the above function checks fail or if you are uncertain, please consult a
competent gunsmith or contact Ruger Customer Service at 336-949-5200 for further
firearm inspection before using the rifle.
31
 MAGAZINE INSPECTION AND CARE
Check the magazine frequently. The rotor must move freely and have adequate
tension so that each cartridge is quickly raised to the feeding position. At the
time of manufacture, proper rotor tension is set by rotating the magazine cap
nut until the rotor stops turning. Then the nut is turned an additional 2 turns
beyond the ‘stop’ position.
To test the rotor tension, load one cartridge into the magazine and then firmly
press against the side of the cartridge case. Remove your finger quickly. The
cartridge should instantly and fully move in to the feeding position. If it does
not, the magazine should be cleaned. If cleaning does not restore proper rotor
tension, do not use the magazine. (NOTE: After testing, remove the test
cartridge.)
When cleaning is necessary, use a solvent that will not rust the metal
components or adversely affect the plastic magazine box. After the magazine has
been soaked in solvent to loosen foreign matter, be certain to shake it vigorously
(with the loading opening away from you) to remove solvent or residue from
within the magazine.
After cleaning, always check to be certain that rotor movement and tension are
correct, and that no solvent or debris remain. Do not disassemble the magazine.
Improper reassembly or improper tensioning of the rotor spring can cause a
potentially dangerous malfunction. If you experience a problem with the
magazine, don’t use it. Get a new one.

DAMAGED, NON-STANDARD, OR IMPROPERLY

ASSEMBLED MAGAZINES SHOULD NOT BE USED.
THEY CAN CAUSE THE RIFLE TO MALFUNCTION.

Exploded view of the 10/22®

magazine components. This
illustration is included to
show the relationship and
names of the magazine
components. As noted in
the text above, the
magazine should not be
disassembled.

32
 CARE AND CLEANING
BEFORE CLEANING, BE CERTAIN THE RIFLE AND ITS
MAGAZINE ARE UNLOADED.
Cleanliness is most important to the function of this blow-back operated
autoloading firearm. Any failures to feed or extract rounds may be indications of
a dirty chamber. Use commercially available bore cleaning solution and a brass
brush, followed by drying with a cloth patch, to remove any powder residue. An
excess of dirt, powder residue, or oil in the chamber will cause malfunctions and
may result in potentially dangerous cartridge case ruptures and release of hot
gasses and case fragments when firing.
At regular intervals, or whenever the rifle has been exposed to sand, dust,
extreme humidity, condensation, immersion in water, or other adverse
conditions, disassemble, clean and oil it. Proper periodic maintenance is essential
to the reliable functioning of any firearm.
CAUTION: THE USE OF CAUSTIC OR ACETONE-BASED CLEANERS ARE NOT
RECOMMENDED AS THE SOLVENT MAY HARM THE FINISHED SURFACES,
PLASTICS, LAMINATES, COMPOSITES, RUBBER GRIPS, OR OTHER
MATERIALS USED IN THE CONSTRUCTION OF YOUR FIREARM. BEFORE
CLEANING YOUR FIREARM, ALWAYS TEST THE CLEANING AGENT/SOLUTION
IN AN INCONSPICUOUS AREA ON ANY PART YOU ARE GOING TO CLEAN
WITH IT (INCLUDING, BUT NOT LIMITED TO, THE STOCK AND EXTERIOR
PORTIONS OF THE BARREL AND RECEIVER) TO ENSURE IT WILL NOT HARM
THE FINISH. NEVER USE AUTOMOTIVE OR PAINT STRIPPING PRODUCTS TO
CLEAN YOUR FIREARM.
An on-line video demonstrating the proper cleaning procedure of the 10/22®
rifles can be viewed by going to Ruger.com/TechTips.
To clean the rifle, proceed as follows:
1. Disassemble (field-strip) the rifle to the extent described on page 29.
2. Using a cleaning rod, run a properly sized, solvent-wetted patch through the
bore several times. Then attach a solvent-wetted bristle brush to a cleaning rod
and run it back and forth the full length of the bore as many times as
necessary to remove grease and dirt from the bore and chamber. Clean bore
with dry patches and examine. Bore fouling can contribute to reduced
accuracy, and grease accumulation in the chamber can interfere with proper
feeding of cartridges from the magazine.
3. Using powder solvent on a clean patch or bristle brush, remove powder residue
from all components of the mechanism. After cleaning, run a dry patch
through the bore, then follow with a patch that is very lightly oiled. Wipe all
surfaces clean with cloth, then wipe all surfaces with a patch or cloth that has
been very lightly oiled.
NOTE: Only a light application of oil is needed to provide adequate lubrication
of moving parts and to prevent rust. Excess accumulations of oil tend to
attract particles of dust and dirt and may congeal in cold weather which can
interfere with the safe and reliable functioning of the rifle.

33
 WARNING – LUBRICATION
Firing a rifle with oil, grease, or any other material
even partially obstructing the bore may result in
damage to the rifle and serious injury to the
shooter and those nearby. Do not spray or apply
IL lubricants directly on ammunition. If the powder
O of a cartridge is affected by the lubricant, it may
not be ignited, but the primer firing may push the
bullet into the bore where it may be lodged. Firing
a subsequent bullet into the obstructed bore may
damage the rifle and cause serious injury or death
to the shooter and those nearby. Use lubricants
properly. You are responsible for the proper care
and maintenance of your firearms.
IMPROPER LUBRICATION
DESTROYS FIREARMS

STORAGE
FIREARMS SHOULD NOT BE STORED LOADED!

USE THE LOCKING DEVICE SUPPLIED WITH THE RIFLE

TO RENDER IT INOPERATIVE FOR SAFE STORAGE.
(SEE PAGE 10)

Do not store the rifle in a leather case or scabbard. Leather attracts moisture,
even though it may appear to be dry.

WARNING – STORAGE
• Never place or store any firearm in
such a manner that it may be
dislodged. Firearms should always be
stored securely and unloaded, away
from children and careless adults.
• Use the locking device supplied with
the rifle for storage. The use of a
locking device or safety lock is only
one aspect of responsible firearms
storage.
• For increased safety, firearms should
be stored unloaded in a location that
is both separate from their
ammunition and inaccessible to
children and any other unauthorized
person.

STORE SECURELY & UNLOADED

34
MAINTENANCE OF STAINLESS STEEL RIFLES
Firearms and components made of stainless steel are relatively more resistant to
corrosion than those of blued steel. However, in the interest of proper operation
and long life of a stainless steel firearm, inspect it frequently and clean, lubricate
and apply an appropriate rust preventative.
Sometimes discoloration occurs from perspiration or from contact with some
types of firearm cases. Rusting may occur as a result of the firearm being exposed
to moisture, salt air or chemicals.
Minor discoloration can usually be removed by rubbing the stainless area with an
abrasive ink eraser, crocus cloth, or a “metal polishing” compound. When using
any of these abrasives, proceed with care and use light pressure to achieve a
blending of “color” with those areas that are not discolored. Do NOT use abrasives
on the clear coating of the aluminum alloy receiver and trigger housing.
External surfaces most subject to rusting from handling, or from exposure to the
elements, should be cleaned and wiped dry after use or after exposure to adverse
conditions. If the rifle is to be stored, coat it with a light film of oil or
preservative. Where the rifle is in continuing use, and the presence of oil or
grease would be objectionable, then the external surfaces can be coated (after
cleaning and drying) with a paste wax formulated for use on metals. Apply the
wax sparingly, allow time for it to dry hard, then buff lightly with a soft cloth.
When applying the wax, take care that it does not get into the mechanism or on
the functioning parts or in the bore.

ATTACHING SCOPE BASE ADAPTER

To attach Scope Base Adapter to rifle receiver:
1. Retract cocking handle, lock bolt open and push safety to “on” position. Be
sure firearm is completely empty.
2. Using a #1 flat head screwdriver of appropriate size, unscrew the four filler
screws from the receiver by turning them counterclockwise. These screws may
be quite tight. NOTE: Failure to use a properly sized flat head screwdriver
may damage your rifle’s receiver. Never use a screwdriver to remove the filler
screws that exceeds the width of the filler screw slot.
3. Position adapter on receiver and place a base-mounting screw in each hole of
the adapter. Turn each screw until it just catches the threads in the receiver
hole, but don’t tighten the screws at this point.
4. Starting at the first screw, turn each screw part way in; then move to the next
screw, repeating the procedure until all four screws are tightened to a
maximum torque setting of 12-15 inch/lb.
5. Release the cocking handle; then retract it several times, permitting it to snap
forward. If the bolt seems to bind, determine which screw is binding the top of
the bolt. If it is necessary to shorten a screw, be certain to chamfer its top so it
does not cross thread the hole in the receiver.
6. Attach scope bases and scope to the adapter in accordance with their
instructions.
35
Scope mounting precautions: Do not remove the scope base filler screws (there
are four in the receiver) unless the supplied scope base adapter or other suitable
base is to be mounted with properly fitting screws. Do not deepen or alter the
screw holes that are in the Ruger® 10/22®. Do not place any thread locker (such
as LOCTITE®) into the screw holes in the receiver, as the thread locker can drip
into the bolt or receiver and cause potentially dangerous malfunctions.

Tip-Off Style
Scope Base
Adapter

Weaver-Style
Scope Base
Adapter

SIGHT ADJUSTMENT
The folding leaf rear sight is adjustable for elevation. The slide must be moved
one graduation to change the point of impact by approximately one inch at 25
yards. Use a small screwdriver with a blade tip that exactly fits the screw-head.
Loosen the screw(s) only slightly so the slide doesn’t move too freely. Move the
slide in the direction you want the point of impact of the bullet to move. When
the slide is positioned at the desired height, carefully tighten screw(s).
Lateral (windage) adjustment is made by ‘drifting’ the sight base in its slot. Place
a short brass rod against the sight base (and only the base) and tap the sight in
the direction you wish to move the point of bullet impact. Before moving the
sight, pencil mark an index line on the sight base and rib so that sight movement
can be detected.

SUGGESTED SIGHT PICTURE

Top of front sight even with top of
rear sight slide. Front sight
centered in notch of rear sight
slide. Target bull’s-eye centered on
top of front sight.
Note that the rear sight blade can
be reversed to give a square notch
rear sight picture.

36
 SERVICE AND PARTS POLICY
If you have any question regarding the performance of your RUGER® 10/22®
rifle or carbine please contact our Customer Service online at Ruger.com or call
the Customer Service Dept. at 336-949-5200. Fully describe all circumstances
and conditions involved. If you should need to return your rifle to the factory for
repair, or order parts for it, please comply with the following suggestions for
prompt service:

WARNING: BEFORE SHIPPING ANY FIREARM, BE

ABSOLUTELY CERTAIN THAT IT IS UNLOADED. DO NOT
SHIP CARTRIDGES WITH A FIREARM.

SHIPPING FIREARMS FOR REPAIR

NOTE: You must obtain a Repair Authorization Number before returning your
firearm. An authorization number can be obtained by contacting Customer
Service online at Ruger.com or calling the Customer Service Department at 336-
949-5200. Firearms should be sent prepaid. We will not accept collect shipments.
Any RUGER® 10/22® rifle returned to the factory for repair should be sent to:
Sturm, Ruger & Company, Inc., Customer Service Department, 411 Sunapee
Street, Newport, NH 03773.
The Federal Gun Control Act, as well as the laws of most states and localities, do
not prohibit an individual (who is not otherwise barred from purchasing or
possessing a firearm) from shipping a firearm directly to the manufacturer for
repair. However, before you ship your firearm to us, be certain that your state or
locality does not have a law or regulation which will prohibit you from receiving
the firearm (or any included magazines) from us after repair. If such receipt is
prohibited, please have a federally licensed firearms dealer ship the firearm to us.
If your firearm is sent to us by a dealer, it will be returned to that dealer after
being repaired. If a handgun (pistol or revolver) is shipped by an individual who
does not hold a Federal Firearms License, it must be shipped for overnight
delivery via U.P.S., Federal Express or other, similar private overnight service.
NOTE: Persons who do not hold a Federal Firearms License are prohibited by
Federal law from shipping a handgun by U.S. Mail. Handguns mailed in violation
of the law may be impounded or confiscated by the Post Office and the non-FFL
may be subject to prosecution. Rifles and shotguns may be shipped via U.S. Mail.
Please do not include rifle case, sling, telescopic sights or custom accessories
with a firearm being shipped to the factory for service. DO NOT SEND
FIREARM BOXES OR LITERATURE THAT YOU CONSIDER TO BE
COLLECTOR’S ITEMS – THESE ARE INVARIABLY DAMAGED OR
DESTROYED IN SHIPMENT. Always insure your shipment.
Enclose a letter which includes your name, address, telephone number, firearm
serial number and model, and repair authorization number. Describe in detail
the trouble you have experienced with your firearm, or the work you wish to
have done. Merely stating that the firearm “needs repair” is inadequate
information. Please enclose copies of any previous correspondence.

37
All work performed is subject to a minimum labor charge and charges for
shipping and handling. Most models can be reblued, but custom gunsmithing
service or nonstandard alterations are NOT AVAILABLE from Ruger Customer
Service Departments. Please contact the Customer Service Department for
pricing information.

WARNING –PARTS PURCHASERS

• It is the purchaser’s responsibility to be
absolutely certain that any parts ordered from
the factory are correctly fitted and installed.
• Firearms are complicated mechanisms and
IMPROPER FITTING OF PARTS MAY RESULT
IN A DANGEROUS MALFUNCTION, DAMAGE
TO THE FIREARM, AND SERIOUS INJURY TO
THE SHOOTER AND OTHER PERSONS.
• The purchaser and installer of parts must
accept full responsibility for the correct
adjustment and functioning of the firearm
after such installation.

PARTS MUST FIT CORRECTLY

ORDERING PARTS
Please contact the Newport, New Hampshire Customer Service Department for
parts availability and current prices. All written parts orders for the RUGER®
10/22® rifle should be sent to: Sturm, Ruger & Company, Inc., Customer
Service Department, 411 Sunapee Street, Newport, NH, 03773, 336-949-5200.
We cannot comply with open account or C.O.D. requests. Payment in full via
credit card (Visa or MasterCard only), money order or certified bank check (no
personal checks or cash, please) is required before any service will be performed.
Please provide your credit card number, your name as it appears on the credit
card, the expiration date, and the 3-digit security code. All parts orders are
subject to a minimum charge and charges for shipping and handling. Order parts
by Part Name and specify the model and entire serial number of the firearm
for which the parts are being ordered. There is a minimum labor charge plus a
shipping and handling charge if the parts are factory fit. All factory fit parts are
fit on an exchange basis only. We will not return the replaced parts. Please
contact the Customer Service Department for pricing information.
Because the receiver is a serial numbered component, it is defined as a “firearm”
by Federal law and is not sold as a separate component.
*Parts designated by an asterisk must be factory fit. These parts are fit on an
exchange basis only. We will not return the replaced parts. We will not return
any part that is broken, malfunctioning, badly worn or has been modified. See
“Warning — Parts Purchasers,” above.

WARNING: A firearm containing broken, malfunctioning, or

badly worn parts should not be fired.

38
 RUGER® 10/22® RIFLE
PARTS LIST
Design, prices and specifications subject to change without notice.
SPECIFY MODEL, CALIBER AND SERIAL NO. WHEN ORDERING
(See Exploded View Pages 41 - 43)

Key Part Name

1 Barrel
† 2 Receiver
3 Receiver Cross Pin, 2 Req’d
4 Receiver Filler Screw, 4 Req’d
5 Barrel Retainer V-Block
6 Barrel Retainer Screw, 2 Req’d
7 Bolt Assembly – Complete
Includes Key Nos. 8 - 14
(See Exploded View p. 42)
8 Bolt
9 Firing Pin
10 Firing Pin Rebound Spring
11 Firing Pin Stop Pin
12 Extractor
13 Extractor Spring
14 Extractor Plunger
15 Cocking Handle, Guide Rod &
Recoil Spring Assembly
16 Trigger Guard Assembly –
Complete
Includes Key Nos. 17 - 40
(See Exploded View p. 42)
17 Trigger Guard
18 Bolt Lock
19 Bolt Lock Spring
* 20 Hammer
21 Hammer Pivot Pin
22 Hammer Strut
23 Hammer Spring
24 Hammer Strut Washer

* Parts so marked must be factory fit.

† The receiver is a serial-numbered part and is not offered for sale.

39
 Key Part Name
25 Ejector
26 Safety Detent Plunger Spring
27 Safety Detent Plunger
* 28 Safety
29 Disconnector & Trigger Pivot Pin
30 Disconnector
31 Sear Spring
* 32 Trigger
* 33 Sear
34 Trigger Pivot Pin
35 Trigger Plunger Spring
36 Trigger Plunger
37 Magazine Latch
38 Magazine Latch Pivot &
Ejector Pivot Pin, 2 Req’d
39 Magazine Latch Plunger Spring
40 Magazine Latch Plunger
41 Stock
42 Butt Plate
43 Butt Plate Screw, 2 Req’d
44 Rear Sight
45 Front Sight
46 Bolt Stop Pin
47 Barrel Band
48 Barrel Band Screw
49 Magazine Assembly
50 Scope Base Adapter
51 Scope Base Screws, 4 Req’d
52 Take Down Screw
53 Sling Swivel, Front
54 Sling Swivel, Rear

* Parts so marked must be factory fit.

40
RUGER® 10/22® CARBINE

41
 10/22® BOLT ASSEMBLY

10/22®
TRIGGER GUARD ASSEMBLY

42
 RUGER® 10/22®
DELUXE SPORTER

RUGER® 10/22®
TARGET RIFLE

RUGER® 10/22® RIFLE &

10/22® COMPACT RIFLE

43
 RUGER® 10/22® TACTICAL RIFLE
SUPPLEMENTAL PARTS LIST & EXPLODED VIEW

Key Part Name

1 Barrel
55 Flash Hider

RUGER® 10/22 TAKEDOWN®

SUPPLEMENTAL PARTS LIST
(See Exploded View on Page 45)
Key Part Name
1 Barrel
† 2 Receiver
3 Buttstock Assembly
* 4 Insert
5 Detent Spring
6 Safety Detent Plunger
7 Adjusting Knob
8 Spacer
9 Spacer Pin
10 Clamp
11 Barrel Retainer Screws, 2 Req’d
12 Take Down Screw
13 Locking Plunger
14 Locking Plunger Detent
15 Locking Plunger Spring
16 Mounting Screws, 2 Req’d
17 Locking Lever
18 Block
19 Stock – Forend
20 Barrel Band, Black Plastic
21 Barrel Band Screw
22 Barrel Band Retaining Nut

† The receiver is a serial-numbered part and is not offered for sale.

* Parts so marked must be factory fit.

44
 RUGER® 10/22 TAKEDOWN®
SUPPLEMENTAL PARTS EXPLODED VIEW

45
THE BASIC RULES OF SAFE FIREARMS HANDLING
We believe that Americans have a right to purchase and use firearms for lawful
purposes. The private ownership of firearms in America is traditional, but that
ownership imposes the responsibility on the gun owner to use his firearms in a way
which will ensure his own safety and that of others. When firearms are used in a safe
and responsible manner, they are a great source of pleasure and satisfaction, and
represent a fundamental part of our personal liberty.
Firearms do not cause accidents! Firearms accidents are almost always found to have
been the result of carelessness or ignorance on the part of the shooter of the basic
rules of safe gun handling.
The following rules must be observed by gun users at all times. Safe gun handling is
not just desirable, it is absolutely essential to your safety, the safety of others, and the
continuation of gun ownership and sport shooting as we know it today.
1. LEARN THE MECHANICAL AND HANDLING
CHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. The
method of carrying and handling
firearms varies in accordance with the
mechanical provisions for avoiding
accidental discharge and the various
proper procedures for loading and
® unloading. No person should handle
RUGER
CTION
MANUA
L any firearm without first having
INSTRU NS
STRUCTIO IS
READ TH E IN
NINGS IN
TH
RE
thoroughly familiarized himself with
AND WARCAREFULLY BEFO
MANUAL IS FIREARM.
USING TH
the particular type of firearm he is
using, and with safe gun handling in
general.
2. ALWAYS KEEP THE
MUZZLE POINTED IN A
SAFE DIRECTION.
Be sure of the bullet stop behind your
target, even when dry-firing. Never let
the muzzle of a firearm point at any
part of your body or at another
person. This is particularly important
when loading or unloading a firearm.
In the event of an accidental
discharge, no injury can occur as
long as the muzzle is pointing in a
safe direction. A safe direction means
a direction that will not permit a
discharged bullet to strike a person, or to strike an object from which the
bullet may ricochet.
46
A safe direction must take into account the fact that a bullet may
penetrate a wall, ceiling, floor, window, etc., and strike a person or
damage property. Make it a habit to know exactly where the muzzle of
your gun is pointing whenever you handle it, and be sure that you are
always in control of the direction in which the muzzle is pointing, even
if you fall or stumble. Keep your finger off the trigger until you are ready
to shoot.

3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN

USE.
Firearms should be loaded only
when you are in the field or on the
4 target range or shooting area,
ready to shoot. Firearms and
ammunition should be securely
locked in safes, racks or cabinets,
3 or by using the locking device
supplied with the firearm, when
not in use. Ammunition should
safely be stored separate from
1 firearms. Store your firearms out
SAFETY “ON” 2 of sight of visitors and children. It
is the gun owner’s responsibility to
be certain that children and
persons unfamiliar with firearms cannot gain access to firearms,
ammunition, or components.

4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS

BEFORE SHOOTING.
Even a bit of mud, snow or excess
lubricating oil or grease in the
bore may cause the barrel to
bulge, or even burst on firing, and
can cause serious injury to the
shooter and bystanders. Be sure
that you are using ammunition of
the proper caliber and loading for
the gun you are using. If the
report or recoil on firing seems
weak, or doesn’t seem quite right,
CEASE FIRING IMMEDIATELY,
unload your firearm, and check to
be sure that no obstruction has
become lodged in the barrel. Never try to shoot out an obstruction!
47
 5. BE SURE OF YOUR
TARGET BEFORE YOU
SHOOT.
Don’t shoot unless you know
exactly where your bullet is going
to strike. Be sure of the bullet
stop behind your target, even
when dry-firing with an unloaded
gun. If you are in the field
hunting, do not fire at a
movement or noise. Take the time
to be absolutely certain of your
target before you pull the trigger.

6. WEAR SHOOTING
GLASSES AND HEARING
PROTECTION WHEN
YOU SHOOT.
All shooters should wear
protective shooting glasses and
adequate hearing protection when
shooting. Exposure to shooting
noise can damage hearing, and
wearing adequate eye protection
when shooting is essential.

7. NEVER CLIMB A TREE

OR FENCE WITH A
LOADED FIREARM.
Put the firearm down carefully
before climbing a fence, and
unload it before climbing or
descending a tree or jumping over
a ditch or other obstruction. Never
pull or push a loaded firearm
toward yourself or another person.
When in doubt, or whenever you
are about to do anything awkward,
unload your gun!

48
8. DON’T SHOOT AT A
HARD SURFACE OR AT
WATER.
Bullets can glance off many
surfaces like rocks or the surface
of water and travel in
unpredictable directions with
considerable velocity.

9. NEVER TRANSPORT A
LOADED FIREARM.
Firearms should always be
unloaded before being placed in a
vehicle. A suitable carrying case
or scabbard should be used to
carry an unloaded firearm to and
from the shooting area.

10. AVOID ALCOHOLIC

BEVERAGES WHEN
SHOOTING.
Don’t drink until the day’s
shooting is over. Handling
firearms while under the
influence of alcohol in any form,
or medications that could affect
your judgment or coordination,
constitutes a criminal disregard
for the safety of others.

49
 A BRIEF ACCOUNT OF AN EXTRAORDINARY
®
ACHIEVEMENT: RUGER FIREARMS
Sturm, Ruger & Company, Inc., had its beginning in a small machine
shop occupying a rented frame building in Southport, Connecticut. In
January, 1949, with an initial investment of only $50,000 and an idea,
William B. Ruger and Alexander M. Sturm started production of a .22
caliber autoloading pistol–a design which was so successful that it
became the cornerstone upon which one of the most comprehensive
lines of sporting firearms ever made in America was established. After
Alex Sturm’s death in 1951, William B. Ruger continued to direct the
Company until his death in 2002. William B. Ruger, Jr. continued to
provide guidance, which helped make this Company a sound and
successful enterprise, until his retirement in 2006. The Company has
continued to prosper, under new management and guidance from our
Board, with new products and fresh perspectives.
Ruger, in this relatively short time, has established itself as a leading
small arms design organization, developing a unique and broad line of
fine quality sporting, military and police firearms to become one of the
world’s most famous producers of revolvers, pistols, rifles and shotguns.
Since 1949, Ruger craftsmen have built many millions of firearms.
During its five decades of growth and progress under the leadership of
William B. Ruger, the Company developed a business philosophy and
implemented policies which represent a constructive influence in the life
of modern America. From the beginning, Ruger played a positive role in
conservation efforts and has supported the interests of shooters through
such groups as the National Rifle Association, National Shooting Sports
Foundation, and many regional sportsmen’s organizations.
The Company has always endeavored to market its firearms for
constructive and recreational purposes, to emphasize the traditional and
responsible aspects of shooting, to render meaningful public services,
and to encourage shooters in constructive, responsible, and safe
participation in the shooting sports. Its motto, “Arms Makers For
Responsible Citizens®,” exemplifies this Company philosophy.
Today, Ruger® is particularly mindful of those elements which have
contributed to the creation of its success, and extends heartfelt thanks to
its many loyal employees and customers.

Instruction manuals for all Ruger® firearms,

can be downloaded from our website at:
Ruger.com

50
NOTES

51
 WHY NO WARRANTY CARD HAS BEEN
PACKED WITH THIS NEW RUGER® FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require any
seller or manufacturer of a consumer product to give a written
warranty. It does provide that if a written warranty is given, it must be
designated as “limited” or as “full” and sets minimum standards for a
“full” warranty. Sturm, Ruger & Company, Inc. has elected not to
provide any written warranty, either “limited” or “full”, rather than to
attempt to comply with the provisions of the Magnuson-Moss Act and
the regulations issued thereunder. There are certain implied
warranties under state law with respect to sales of consumer goods. As
the extent and interpretation of these implied warranties varies from
state to state, you should refer to your state statutes. Sturm, Ruger &
Company wishes to assure its customers of its continued interest in
providing service to owners of Ruger® firearms.

STURM, RUGER & Company, Inc.

411 Sunapee Street
Newport, New Hampshire 03773 U.S.A.
Ruger.com
Arms Makers For Responsible Citizens®
A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGER®
FIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST, OR IT MAY BE
DOWNLOADED FROM OUR WEBSITE AT RUGER.COM.
THESE INSTRUCTION MANUALS CONTAIN IMPORTANT
WARNINGS WHICH MUST BE UNDERSTOOD
BEFORE USING THESE FIREARMS.
The Following are Sturm, Ruger & Co., Inc. Trademarks: “All-Weather,” “Bisley,” “Gold Label,” “I’m a Ruger
American,” “LC6,” “LCR-357,” “LC380CA,” “LC Carbine,” “LC Charger,” “Mark II,” “Mark III,” “Mark IV,” “Model 96,”
“P345,” “P345D,” “P345PR,” “P85,” “P89,” “P90,” “P91,” “P93,” “P94,” “P95,” “P97,” “Power Bedding,” “PC
Carbine,”“ReadyDot,” “R.I.O.S.,” “Ruger Marksman Adjustable,” “Ruger 77/50,” “Ruger 10/17,” “Ruger 10/22 Takedown”
phrase & logo design, “Secure Action,” “Security-Six,” “Service-Six,” “77/357,” “SFAR,” “Single-Seven,” “Speed-Six,”
“SR45,” “SR-556C,” “SR-556VT,” “SR9c,” “SR40c,” “Super Bearcat,” “Target Grey,” “10/22-FS,” “This is Ruger. This is
America.,” “Tri-Flex,” “22 Charger,” “22/45,” “22/45 RP,” and “Your Next Handgun.”
The Following are Registered U.S. Trademarks Belonging to Sturm, Ruger & Co., Inc.: “AC-556,” “AR-556,” “Arms
Makers For Responsible Citizens,” “Bearcat,” “Blackhawk,” “BX-15,” “BX-25,” “BX-Trigger,” Eagle - solid logo design,
Eagle Hard “R” logo holding gun, Eagle ‘R’ - soft ‘R’ & hard ‘R’ logo design, Eagle w/‘SR’, Eagle w/soft ‘R’ linear logo
design, Eagle w/hard ‘R’ linear logo design, Eagle w/soft ‘R’ stacked logo design, Eagle w/hard ‘R’ stacked logo design,
Eagle w/soft ‘R’ linear logo design & “Rugged, Reliable Firearms” below logo, Eagle w/hard ‘R’ linear logo design &
“Rugged, Reliable Firearms” below logo, “EC9s,” “Elite 452,” “GP100,” “Hawkeye,” “It’s Mine and It’s American,” “It’s
Mine. And It’s American,” “LC380,” “LC9,” “LC9s,” “LC9s Pro,” “LCP,” “LCR,” “LCRx,” “M77,” “Match Champion,”
“MAX-9,” “Mini-14,” “Mini Thirty,” “9E,” “Old Army,” “Redhawk,” “RUGER,” “Ruger American,” “Ruger American
Pistol,” “Ruger American Pistol” flag design, “Ruger American Rifle,” “Ruger American Rimfire,” “Ruger Custom Shop,”
“Ruger Hunting” - phrase & logo design, “Ruger Precision,” “Ruger Precision Rifle” - phrase & logo design, “Ruger
77/17,” “Ruger 77/22,” “Ruger 77/44,” “Ruger-5.7,” “Ruger SP101,” “Ruger Titanium,” “Ruger 22/45 Lite,” “Ruger
Vaquero,” “Rugged, Reliable Firearms,” “Security-9,” “Security-380,” “Silent-SR,” “Single-Nine,” “Single-Six,” “Single-
Ten,” the “SR” Design, “SR9,” “SR40,” “SR-22,” “SR22,” “SR-556,” “SR-556 Takedown,” “SR-762,” “SR1911,” “Super
Redhawk Alaskan,” “10/22,” & “Wrangler.”