Compressive Strength of Cylindrical Concrete Specimens: Significance and Use

Compressive Strength of Cylindrical Concrete Specimens
Overview
Effective: August 1999 – May 2000.
Part I of this method covers determining compressive strength of cylindrical concrete
specimens such as molded cylinders and drilled cores. It is limited to concrete having a
unit weight in excess of 800 kg/m3 (50 lb/ft3 ). Except for editorial differences, this test
method is identical with ASTM C 39 and AASHTO T 22, Part II discusses the use of
neoprene caps during this testing.
Part I, Determining Compressive Strength of Cylindrical Concrete Specimens
This part determines compressive strength of cylindrical concrete specimens such as
molded cylinders and drilled cores. It is limited to concrete having a unit weight in
excess of 800 kg/m3 (50 lb/ft3 ).
Significance and Use
Below is information regarding the significance and use of this test method. Exercise
care interpreting the significance of compressive strength determinations by this test
method, since strength is not a fundamental or intrinsic property of concrete made from
given materials. Values obtained will depend on the size and shape of the specimen,
batching, mixing procedures, the methods of sampling, molding, fabrication, age,
temperature, and the moisture conditions during curing. Use this method to determine
compressive strength of cylindrical specimens prepared and cured according to test
methods “Tex-424-A, Obtaining and Testing Drilled Cores of Concrete, Tex-447-A,
Making and Curing Concrete Test Specimens,” and/or “Tex-450-A, Capping Cylindrical
Concrete Specimens.” The results of this test method may be used as a basis for quality
control of concrete proportioning, mixing, and placing operations; determination of
compliance with specifications; control for evaluating effectiveness of admixtures and
similar uses.
Specimens
• Specimens shall not be tested if any diameter of a cylinder differs from any other
diameter of the same cylinder by more than 2%.
NOTE: This may occur when single use molds are damaged or deformed during
shipment, when flexible single use molds are deformed during molding, or when a
core drill deflects or shifts during drilling.
• Neither end of compressive test specimens should depart from perpendicularity

to the axis by more than 0.5° (3 mm in 300 mm [1/8 in. in 12 in.]).
• Cap the ends of compression test specimens according to Test Method “Tex-450-
A, Capping Cylindrical Concrete Specimens.”
• Determine the diameter used for calculating the cross-sectional area of the test
specimen to the nearest 0.25 mm (0.01 in.) by averaging two diameters
measured at right angles to each other at about mid-height of the specimen.
• The number of individual cylinders measured for determining average diameter
may be reduced to one for each ten specimens or three specimens per day,
whichever is greater, if all cylinders are known to have been made from a single
lot of reusable or single-use molds which consistently produce specimens with
average diameters within a range of 0.51 mm (0.02 in).
• When the average diameters do not fall within the range of 0.51 mm (0.02 in.) or
when the cylinders are not made from a single lot of molds, each cylinder tested
must be measured and the value used to calculate the unit compressive strength
of that specimen.
• When the diameters are measured at the reduced frequency, the cross-sectional
areas of all cylinders tested on that day shall be computed from the average of
the diameters of the three or more cylinders representing the group tested that
day.
• The length shall be measured to the nearest 0.05D when the length to diameter
ratio is less than 1.8, or more than 2.2, or when the volume of the cylinder is
determined from measured dimensions.
Test Procedure
The following describes the procedure for compression testing of cylindrical concrete
specimens:
• Test specimens in a moist condition.
• Perform compression tests of moist cured specimens as soon as practicable
after removal from moist storage.
• Keep test specimens moist by any convenient method during the period between
removal from moist storage and testing.
• Break all test specimens for a given test age within the permissible time
tolerances prescribed:
Time tolerance
Test age Permissible

Tolerance
24h ±0.5 h or 2.1%
3 days 2 h or 2.8%
7 days 6 h or 3.6%
28 days 20 h or 3.0%
90 days 2 days 2.2%
The following table details compression testing cylindrical concrete specimens.
Compression Testing of Cylindrical Concrete Specimens
Step Action
1 • Place the lower bearing block, with its hardened face up, on the table or
platen of the testing machine directly under the spherically seated (upper)
bearing block.
• Clean the bearing faces of the upper and lower bearing blocks and the test
specimen and place the test specimen on the lower bearing block.
• Carefully align the axis of the specimen with the center of thrust of the
spherically seated block.
• As the spherically seated block is brought to bear on the specimen, rotate
its movable portion gently by hand, so that uniform seating is obtained.
2 • Apply the load continuously and without shock.
• For testing machines of the screw type, the moving head shall
travel at a rate of approximately 1.3 mm (0.05 in.)/minutes when
the machine is running idle.
• For hydraulically operated machines, the load shall be applied at a
rate of movement (platen to cross-head measurement)
corresponding to a loading rate on the specimen within the range
of 0.14 to 0.34 MPa/s (20 to 50 psi/s). Maintain the designated rate
of movement at least during the latter half of the anticipated loading
phase of the testing cycle.
• During the application of the first half of the anticipated loading phase a
higher rate of loading shall be permitted.
• Make no adjustment in the rate of movement of the platen at any time
while a specimen is yielding rapidly immediately before failure.
• Apply the load until the specimen fails, and record the maximum load
carried by the specimen during the test.
• Note the type of failure and the appearance of the concrete.
Calculations
Use the following calculations to determine the compressive strength of the specimens:
Calculate the compressive strength of the specimen by dividing the maximum load
carried by the specimen during the test by the average cross-sectional area determined
as previously described and express the result to the nearest 50 kPa (10 psi).
If the specimen length to diameter ratio is less than 1.8, correct the result obtained by
multiplying by the appropriate correction factor shown in the following table:
Correction Factors
L/D 1.75 1.50 1.25 1.00

Factor: 0.98 0.96 0.93 0.87
NOTE 8: These correction factors apply to light weight concrete weighing between 1600
and 1920 kg/m3 (100 and 200 lb/ft3 ) and to normal weight concrete. They are
applicable to concrete dry or soaked at time of loading. Values not given in the table
shall be determined by interpolation. The correction factors are applicable for nominal
concrete strengths from 13.8 to 41.4 MPa (2000 to 6000 psi).
Report
Include the following in the report:
• Identification Number
• Diameter (and length, if outside the range of 1.8D to 2.2D), in inches
• Cross-sectional area, in square millimeters (square inches)
• Maximum load, in Newtons (pounds-force)
• Compressive strength calculated to the nearest 50 kPa (10 psi)
• Type of fracture, if other than the usual cone (see ‘Sketches of Types of
Fracture’)
• Defects in either specimen or caps
• Age of specimen.
REFERENCE: https://ftp.dot.state.tx.us/pub/txdot-info/cst/TMS/400-
A_series/archives/418-0899.pdf

Compressive Strength of Cylindrical Concrete Specimens: Significance and Use

Uploaded by

Copyright:

Available Formats

Compressive Strength of Cylindrical Concrete Specimens: Significance and Use

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Compressive Strength of Cylindrical Concrete Specimens: Significance and Use

Uploaded by

Copyright:

Available Formats

Compressive Strength of Cylindrical Concrete Specimens

Significance and Use

• Neither end of compressive test specimens should depart from perpendicularity

Test age Permissible

The following table details compression testing cylindrical concrete specimens.

Compression Testing of Cylindrical Concrete Specimens

L/D 1.75 1.50 1.25 1.00

You might also like