Boson NetSim LE functionality and supported commands

Boson NetSim LE has been specifically designed to support several labs from this book.
What that means is that the exact commands required for those labs indeed work, but
commands that aren't required for those labs aren't supported in the product.

As technology evolves, various technical recommendations provided by the numerous

standards committees (and manufacturers that are affected by those modifications),
change with the times.

This can be observed in interesting ways, all the way down to the Cisco router and
Catalyst switch command line interface (or, “CLI” for short) level. For example, there
are several different ways to configure a Cisco router to perform a save of its
configuration data:

Method #1: The newer (or “modern”) CLI command, “Copy Run Start”, performs a save
of the Cisco router’s configuration data. This CLI command is well documented in
modern Cisco courseware, and is the currently recommended method.

Method #2: The older (or “legacy”) CLI command, “Write Mem”, performs an identical
save of the same Cisco router’s configuration data. While this CLI command may still
work, it is no longer documented in current Cisco courseware, and is no longer
recommended.

The Boson NetSim™ LE (or Learning Edition) software product, as provided on the
CDROM within the CCNA INTRO and CCNA ICND (640-8xxx series) books, simulates
only those newer, or more modern, Cisco recommended and documented commands.

If you're having difficulty getting a supported lab to work, you might benefit
from reading over the list of commands that Boson NetSim LE supports in each lab. For
your convenience, a complete listing of all modern commands that are enabled for
completing the included labs (that are documented as enabled in the printed books) are
listed below.

Also note that Boson NetSim LE doesn't let you make as many mistakes as a real router
or switch - for instance, using a different subnet mask than the lab requires will be
rejected by NetSim. The list of commands includes the full syntax of the commands,
so you can compare the commands you're typing to what NetSim is expecting. The list
of commands are a direct pull of what the software is expecting. 
INTRO Commands

The following 92 commands are supported by the Boson NetSim LE for the labs in the
CCNA INTRO Exam Certification Guide.

Conf terminal
Hostname R1
Interface Serial 0
Ip address 163.1.12.201 255.255.255.128
Interface Serial 1
Ip address 163.1.13.201 255.255.255.128
Interface Ethernet 0
Ip address 163.1.1.201 255.255.255.128
Router rip
Network 163.1.0.0
Hostname R2
Ip address 163.1.12.202 255.255.255.128
Encapsulation ppp
Ip address 163.1.23.202 255.255.255.128
Ip address 163.1.2.202 255.255.255.128
Hostname R3
Ip address 163.1.13.203 255.255.255.128
Ip address 163.1.23.203 255.255.255.128
Ip address 163.1.3.203 255.255.255.128
Hostname Sw3
Enable secret cisco
Line vty 0 15
Password cisco
Login
Line console 0
Login
Password cisco
Interface vlan 1
Ip address 163.1.1.213 255.255.255.128
No shutdown
Ip default-gateway 163.1.1.201
Interface fastethernet 0/1
Description trunk to SW1
Interface fastethernet 0/2
Description trunk to SW2
Copy running-config startup-config
Show ip interface brief
Show access-lists
Show ip protocol
Show running-config
Show ip arp
Show ip route
Trace 163.1.13.203
Ping 163.1.13.203
Ip address 10.1.1.1 255.255.255.0
Enable
Disable
Show interface serial 0
Show version
Show flash
Hostname Hannah
Write terminal
Show config
Clock set 16:52:30 31 Dec 2001

Lab 5.pdf
Reload in 600 cause I want to
Erase nvram
Show interfaces status
Show version
Show flash
Hostname Wendell
Hostname sw12
Interface fastethernet 0/1
Enable secret cisco
Interface vlan 1
Ip address 172.30.101.101 255.255.255.0
Exit
Ip default-gateway 172.30.101.1

Lab 6
Write erase
Reload
Enable password fred
Interface Ethernet 0
Ip address 172.30.101.1 255.255.255.0
Interface serial 0
Ip address 172.30.102.1 255.255.255.0
Line vty 0 4
Login
Password cisco
Interface Ethernet 0
Ip address 172.30.103.2 255.255.255.0
Interface serial 0
Ip address 172.30.102.2 255.255.255.0
Clock rate 56000
Ping 172.30.102.2
Ping 172.30.103.2

Extended pings
telnet 172.30.102.2
show users
show sessions
ip host R2 172.30.102.2
telnet R2
show cdp entry *
show cdp neighbor
show cdp interface

ICND Commands

The following 171 commands are supported by the Boson NetSim LE for the labs in the
CCNA ICND Exam Certification Guide

Lab7.pdf
Interface serial 0
Encapsulation frame-relay
Ip address 168.11.123.201 255.255.255.192
Frame-relay interface-dlci 502
Frame-relay interface-dlci 503
Interface Ethernet 0
Ip address 168.11.11.101 255.255.255.192
Router igrp 1
Network 168.11.0.0
Ip address 168.11.123.202 255.255.255.192
Frame-relay interface-dlic 501
Frame-relay interface-dlic 503
Ip address 168.11.12.102 255.255.255.192
Ip address 168.11.123.203 255.255.255.192
Frame-relay interface-dlic 501
Frame-relay interface-dlic 502
Ip address 168.11.13.103 255.255.255.192
Ip route 168.11.12.64 255.255.255.192 168.11.123.202
Ip route 168.11.11.64 255.255.255.192 168.11.123.201
Ip route 168.11.13.64 255.255.255.192 168.11.123.203
Ip route 168.11.12.64 255.255.255.192 168.11.123.202
Frame-relay map ip 168.11.123.202 502 broadcast
Frame-relay map ip 168.11.123.201 501 broadcast
Frame-relay map ip 168.11.123.203 503 broadcast
Frame-relay map ip 168.11.123.202 502 broadcast
Show ip interface brief
Debug ip igrp transactions
Show interface
Show ip protocol
Show frame-relay pvc
Show frame-relay map
Show frame-relay lmi
Interface serial0
Encapsulation frame-relay
Interface serial 0.2 point-to-point
Ip address 170.1.10.1 255.255.254.0
Frame-relay interface-dlci 302
Ip access-group 102 in
Interface serial 0.3 point-to-point
Ip address 170.1.12.1 255.255.254.0
Frame-relay interface-dlci 303
Ip access-group 103 in
Interface serial 0.4 point-to-point
Ip address 170.1.14.1 255.255.254.0
Frame-relay interface-dlci 304 ietf
Ip access-group 104 in
Interface Ethernet 0
Ip address 170.1.3.1 255.255.254.0
Router igrp 1
Network 170.1.0.0
Access-list 102 permit tcp any host 170.1.2.11 eq ftp
Access-list 102 permit tcp any host 170.1.2.11 eq www
Access-list 102 permit tcp any host 170.1.2.12 eq ftp
Access-list 102 permit tcp any host 170.1.2.12 eq www
Access-list 102 deny ip any host 170.1.2.11
Access-list 102 deny ip any host 170.1.2.12
Access-list 102 deny ip 170.1.4.0 0.0.1.255 170.1.6.0 0.0.1.255
Access-list 102 permit ip any any

Access-list 103 permit tcp any host 170.1.2.11 eq ftp

Access-list 103 permit tcp any host 170.1.2.11 eq www
Access-list 103 permit tcp any host 170.1.2.12 eq ftp
Access-list 103 permit tcp any host 170.1.2.12 eq www
Access-list 103 deny ip any host 170.1.2.11
Access-list 103 deny ip any host 170.1.2.12
Access-list 103 deny ip 170.1.6.0 0.0.1.255 170.1.4.0 0.0.1.255
Access-list 103 permit ip any any

Access-list 104 permit tcp any host 170.1.2.11 eq ftp

Access-list 104 permit tcp any host 170.1.2.11 eq www
Access-list 104 permit tcp any host 170.1.2.12 eq ftp
Access-list 104 permit tcp any host 170.1.2.12 eq www
Access-list 104 deny ip any host 170.1.2.11
Access-list 104 deny ip any host 170.1.2.12
Access-list 104 permit ip any any

Interface serial 0
Encapsulation frame-relay
Interface serial 0.1 point-to-point
Ip address 170.1.10.2 255.255.254.0
Frame-relay interface-dlci 301
Interface Ethernet 0
Ip address 170.1.5.2 255.255.254.0
Router igrp 1
Network 170.1.0.0

Interface serial 0
Encapsulation frame-relay
Interface serial 0.1 point-to-point
Ip address 170.1.12.3 255.255.254.0
Frame-relay interface-dlci 301
Interface Ethernet 0
Ip address 170.1.7.3 255.255.254.0
Router igrp 1
Network 170.1.0.0

Interface serial 0
Encapsulation frame-relay ietf
Interface serial 0.1 point-to-point
Ip address 170.1.14.4 255.255.254.0
Frame-relay interface-dlci 301
Interface Ethernet 0
Ip address 170.1.9.4 255.255.254.0
Router igrp 1
Network 170.1.0.0
Show frame-relay map
Show cdp neighbor detail
Lab 18

Ip route 172.30.103.0 255.255.255.0 serial 0

Ip route 172.30.101.0 255.255.255.0 172.30.102.1
Router rip
Network 172.30.0.0
Router igrp 1
Network 172.30.0.0
Debug ip igrp events
Debug ip igrp transactions
Debug ip rip events
No debug all

Lab 19
Ip http server
Access-list 101 permit icmp any 172.30.103.0 0.0.0.255
Access-list 101 deny tcp any host 172.30.103.2 eq telnet
Access-list 101 permit tcp any 172.30.103.0 0.0.0.255 eq telnet
Access-list 101 permit tcp any 172.30.103.0 0.0.0.255 eq www
Access-list 101 permit tcp any host 172.30.102.2
Interface serial 0
Ip access-group in
Ip access-list extended fred
Permit icmp any 172.30.103.0 0.0.0.255
Deny tcp any host 172.30.103.2 eq telnet
Permit tcp any 172.30.103.0 0.0.0.255 eq www
Permit tcp any host 172.30.102.2 eq telnet
Ip access-group fred in
No ip access-group fred in
Access-list 101 permit icmp 172.30.103.0 0.0.0.255 any
Access-list 101 deny tcp host 172.30.103.2 eq telnet any
Access-list 101 permit tcp 172.30.103.0 0.0.0.255 eq telnet any
Access-list 101 permit tcp 172.30.103.0 0.0.0.255 eq www any
Access-list 101 permit tcp 172.30.102.2 eq telnet any
Interface serial 0
Ip access-group 101 in
Write mem

Lab 20

Debug ppp negotiation

Interface serial 1
Ip address 172.30.104.2 255.255.255.0
No frame-relay inverse-arp
Clear frame-relay inarp
Frame-relay map ip 172.30.104.2 202 broadcast
Frame-relay map ip 172.30.104.1 201 broadcast
Encapsulation hdlc
No ip address
Interface serial 1.1 point-to-point
Ip address 172.30.104.1 255.255.255.0
Frame-relay interface-dlci 202
Interface serial 1.1 point-to-point
Ip address 172.30.104.2 255.255.255.0
Frame-relay interface-dlci 201
Encapsulation frame-relay ietf

Lab 21
Vlan database
Vlan 2 name barney-2
Vlan 3 name Wilma-3
Interface fastethernet 0/5
Switchport mode access
Switcport access vlan 2
Interface fastethernet 0/6
Interface fastethernet 0/7
Interface fastethernet 0/8
Interface fastethernet 0/9 – 12
Interface fastethernet 0/12
Switchport mode dynamic desirable
Vlan database
Vtp domain fred
Show vtp status
Show interfaces fastethernet 0/12 switchport
Show interfaces fastethernet 0/12 trunk

Difference between CCNA 2.0 material and the new ICND/INTRO material

One big difference is the inclusion of the 2950 switches these switches still run on the
Cisco IOS but the command line syntax is a little different. For example on the 1912
Catalyst to configure a vlan you would use the following set of commands:

Switch>enable
Switch#config t
Switch(config)#vlan 12 name cisco

On the new Catalyst 2950 switches the command structure is a little different. Now you
type:

Switch>enable
Switch#vlan database
Switch(vlan)#vlan 12 name cisco

Notice there is a completely new mode most of you are not familiar with. This mode is
the vlan database mode denoted by the (vlan) brackets. This is just one example of the
new material included with the new version of the CCNA ICND/INTRO exam.