Red Mahogany Exterior 450 Stain General Finishes | Stained doors, Staining wood, Exterior

General Finishes Red Mahogany Exterior 450 Stain Exterior 450 Stains are premium quality, exterior pigmented stains designed for outdoor projects such fences, patio furniture, garage doors, entrance doors, outdoor kitchens and interior windows. It is not recommended as a deck finish. They contain U.V. absorbers to protect the finish and mildewcides to retard mold.Type: Water BasedAmbers: NoUse: ExteriorRaw Wood Application Only: YesCan Sizes: Quarts, GallonsCoverage: 112 sq. ft/quart, 448 sq. ft/gallonViscosity: MediumApplication: Brush or SprayCoats (#) Required: 1+Hand Apply: YesSpray: YesSpray Tip Sizes: HVLP .043-.051 Medium Air CapTopcoat Required: YesTopcoat Recommended: Exterior 450 TopcoatDry TimeDry Time to Touch: 30 min.Dry Time to Re-coat: 2 hrsDry Time Before Light Use: 7-10 daysDry Time Until Cured: 21 daysVOC: <150 g/LTOPCOAT:Exterior 450 provides a clear drying tough, protective finish that will withstand the rigors of the sun, rain, and wind. It is suitable for vertical surfaces such as fences, patio furniture, garage doors, entrance doors, outdoor kitchens and interior windows. It is not recommended as a deck finish. Fortified with UV absorbers to stabilize the finish, Exterior 450's built-in mildewcide retards mold and mildew growth. Tough and flexible, it will resist the expansion and contraction of the wood through hot summers and cold winter. Exterior 450 performs well as a clear coat or as an optional topcoat over General Finishes Milk Paint. It can also be used as a tint base to create custom colors. Warning: We do not recommend Exterior 450 stains or topcoats for exotic woods Ipe, Teak, or other dense oily woods that will get exposure.Colors: Water White in can (dries crystal clear)*Note: Exterior 450 is designed to let the water permeate the finish, and as it dries, the water releases back out to allow the finish to tighten down again. Temporary cloudiness may occur as the finish dries.*Note: Water topcoats can pull tannins, stains and dyes from surfaces that are not properly prepped. Stain blocking primer may be required under white or light colored paints to prevent bleed-through. GF Stain Blocker is not exterior rated.Water or Oil: Water BasedAmbering: NoSheens: Flat (10 or less), Satin (25-35), Semi-Gloss (50-60), Gloss (85+)Interior/Exterior: ExteriorProduct Type: Urethane/ Acrylic BlendCoats (#): 3 coatsCan Sizes: Quarts, Gallons, 5 Gallon pails, 55 Gallon drumsCoverage: 150 sq. ft/quart, 600 sq. ft/gallonApplication Method: Brush, Roll or SprayBrushable: YesSprayable: YesSpray Tip Sizes: HVLP .043-.051 Medium Air CapDURABILITYDurability (Highest, High, Medium, Low): HighHardness (Koeing): 30Wear (Taber): 95.3 mg lossWater (5 max): 5Chemical (105 max): 92DRY TIMEDry Time to Touch: 30 min.Dry Time to Re-coat: 2 hrs.Dry Time Before Light Use: 7-10 daysDry Time Until Cured: 21 daysTECHNICAL DATAViscosity: MediumViscosity: 350-450 cPsWeight Solids (%): 31%VOC: Low <105 g/L - High <128 g/LSANDING: On bare wood sand to 150- 180 grit. Use 220-400 grit gray flexible sanding pads between coats or 400 grit sandpaper.WARNING: TEST FOR COMPATIBILITY WHEN USING THIS PRODUCT WITH PRODUCTS FROM OTHER BRANDS. General Finishes products should be tested to your complete satisfaction before using. General Finishes will not be responsible for any failure if our products are used in conjunction with other brands of finishes. We do not test General Finishes products with those of another manufacturer and will not accept liability if there is a compatibility issue.