-
Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector
Authors:
C. Agapopoulou,
L. A. Beresford,
D. E. Boumediene,
L. Castillo García,
S. Conforti,
C. de la Taille,
L. D. Corpe,
M. J. Da Cunha Sargedas de Sousa,
P. Dinaucourt,
A. Falou,
V. Gautam,
D. Gong,
C. Grieco,
S. Grinstein,
S. Guindon,
A. Howard,
O. Kurdysh,
E. Kuwertz,
C. Li,
N. Makovec,
B. Markovic,
G. Martin-Chassal,
R. Mazzini,
C. Milke,
M. Morenas
, et al. (12 additional authors not shown)
Abstract:
This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (t…
▽ More
This paper presents the design and characterisation of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector, which is planned for the High-Luminosity phase of the LHC. This prototype, called ALTIROC1, consists of a 5$\times$5-pad matrix and contains the analog part of the single-channel readout (preamplifier, discriminator, two TDCs and SRAM). Two preamplifier architectures (transimpedance and voltage) were implemented and tested. The ASIC was characterised both alone and as a module when connected to a 5$\times$5-pad array of LGAD sensors. In calibration measurements, the ASIC operating alone was found to satisfy the technical requirements for the project, with similar performances for both preamplifier types. In particular, the jitter was found to be 15$\pm$1~ps (35$\pm$1~ps) for an injected charge of 10~fC (4~fC). A degradation in performance was observed when the ASIC was connected to the LGAD array. This is attributed to digital couplings at the entrance of the preamplifiers. When the ASIC is connected to the LGAD array, the lowest detectable charge increased from 1.5~fC to 3.4~fC. As a consequence, the jitter increased for an injected charge of 4~fC. Despite this increase, ALTIROC1 still satisfies the maximum jitter specification (below 65~ps) for the HGTD project. This coupling issue also affects the time over threshold measurements and the time-walk correction can only be performed with transimpedance preamplifiers. Beam test measurements with a pion beam at CERN were also undertaken to evaluate the performance of the module. The best time resolution obtained using only ALTIROC TDC data was 46.3$\pm$0.7~ps for a restricted time of arrival range where the coupling issue is minimized. The residual time-walk contribution is equal to 23~ps and is the dominant electronic noise contribution to the time resolution at 15~fC.
△ Less
Submitted 25 July, 2023; v1 submitted 15 June, 2023;
originally announced June 2023.
-
Status and initial physics performance studies of the MPD experiment at NICA
Authors:
MPD Collaboration,
V. Abgaryan,
R. Acevedo Kado,
S. V. Afanasyev,
G. N. Agakishiev,
E. Alpatov,
G. Altsybeev,
M. Alvarado Hernández,
S. V. Andreeva,
T. V. Andreeva,
E. V. Andronov,
N. V. Anfimov,
A. A. Aparin,
V. I. Astakhov,
E. Atkin,
T. Aushev,
G. S. Averichev,
A. V. Averyanov,
A. Ayala,
V. A. Babkin,
T. Babutsidze,
I. A. Balashov,
A. Bancer,
M. Yu. Barabanov,
D. A. Baranov
, et al. (454 additional authors not shown)
Abstract:
The Nuclotron-base Ion Collider fAcility (NICA) is under construction at the Joint Institute for Nuclear Research (JINR), with commissioning of the facility expected in late 2022. The Multi-Purpose Detector (MPD) has been designed to operate at NICA and its components are currently in production. The detector is expected to be ready for data taking with the first beams from NICA. This document pro…
▽ More
The Nuclotron-base Ion Collider fAcility (NICA) is under construction at the Joint Institute for Nuclear Research (JINR), with commissioning of the facility expected in late 2022. The Multi-Purpose Detector (MPD) has been designed to operate at NICA and its components are currently in production. The detector is expected to be ready for data taking with the first beams from NICA. This document provides an overview of the landscape of the investigation of the QCD phase diagram in the region of maximum baryonic density, where NICA and MPD will be able to provide significant and unique input. It also provides a detailed description of the MPD set-up, including its various subsystems as well as its support and computing infrastructures. Selected performance studies for particular physics measurements at MPD are presented and discussed in the context of existing data and theoretical expectations.
△ Less
Submitted 16 February, 2022;
originally announced February 2022.
-
Topmetal-M: a novel pixel sensor for compact tracking applications
Authors:
Weiping Ren,
Wei Zhou,
Bihui You,
Ni Fang,
Yan Wang,
Haibo Yang,
Honglin Zhang,
Yao Wang,
Jun Liu,
Xianqin Li,
Ping Yang,
Le Xiao,
YuezhaoZhang,
Xiangru Qu,
Shuguang Zou,
GuangmingHuang,
Hua Pei,
Fan Shen,
Dong Wang,
Xiaoyang Niu,
Yuan Mei,
Yubo Han,
ChaosongGao,
Xiangming Sun,
Chengxin Zhao
Abstract:
The Topmetal-M is a large area pixel sensor (18 mm * 23 mm) prototype fabricated in a new 130 nm high-resistivity CMOS process in 2019. It contains 400 rows * 512 columns square pixels with the pitch of 40 μm. In Topmetal-M, a novel charge collection method combing the Monolithic Active Pixel Sensor (MAPS) and the Topmetal sensor has been proposed for the first time. Both the ionized charge deposi…
▽ More
The Topmetal-M is a large area pixel sensor (18 mm * 23 mm) prototype fabricated in a new 130 nm high-resistivity CMOS process in 2019. It contains 400 rows * 512 columns square pixels with the pitch of 40 μm. In Topmetal-M, a novel charge collection method combing the Monolithic Active Pixel Sensor (MAPS) and the Topmetal sensor has been proposed for the first time. Both the ionized charge deposited by the particle in the sensor and along the track over the sensor can be collected. The in-pixel circuit mainly consists of a low-noise charge sensitive amplifier to establish the signal for the energy reconstruction, and a discriminator with a Time-to-Amplitude Converter (TAC) for the Time of Arrival (TOA) measurement. With this mechanism, the trajectory, particle hit position, energy and arrival time of the particle can be measured. The analog signal from each pixel is accessible through time-shared multiplexing over the entire pixel array. This paper will discuss the design and preliminary test results of the Topmetal-M sensor.
△ Less
Submitted 26 January, 2022;
originally announced January 2022.
-
Elliptic flow splittings in the Polyakov-looped Nambu-Jona Lasinio transport model
Authors:
Wen-Hao Zhou,
He Liu,
Feng Li,
Yi-Feng Sun,
Jun Xu,
Che Ming Ko
Abstract:
To incorporate the effect of gluons on the evolution dynamics of the quark matter produced in relativistic heavy-ion collisions, we extend the 3-flavor Nambu-Jona-Lasinio (NJL) transport model to include the contribution from the Polyakov loops. Imbedding the resulting pNJL partonic transport model in an extended multiphase transport (extended AMPT) model, we then study the elliptic flow splitting…
▽ More
To incorporate the effect of gluons on the evolution dynamics of the quark matter produced in relativistic heavy-ion collisions, we extend the 3-flavor Nambu-Jona-Lasinio (NJL) transport model to include the contribution from the Polyakov loops. Imbedding the resulting pNJL partonic transport model in an extended multiphase transport (extended AMPT) model, we then study the elliptic flow splittings between particles and their antiparticles in relativistic heavy-ion collisions at RHIC-BES energies. We find that a weak quark vector interaction in the partonic phase is able to describe the elliptic flow splitting between protons and antiprotons in heavy-ion collisions at $\sqrt{s_{NN}}=7.7$ to 39 GeV. Knowledge on the quark vector interaction is useful for understanding the equation of state of quark matter at large baryon chemical potentials and thus the location of the critical point in the QCD phase diagram.
△ Less
Submitted 15 September, 2021; v1 submitted 20 May, 2021;
originally announced May 2021.
-
Prototyping of a 25 Gbps optical transmitter for applications in high-energy physics experiments
Authors:
C. -P. Chao,
S. -W. Chen,
D. Gong,
S. Hou,
X. Huang,
C. -Y. Li,
C. Liu,
T. Liu,
M. Qi,
J. Ye,
X. Zhao,
L. Zhang,
W. Zhou
Abstract:
Development of optical links with 850 nm multi-mode vertical-cavity surface-emitting lasers (VCSELs) has advanced to 25 Gbps in speed. For applications in high-energy experiments, the transceivers are required to be tolerant in radiation and particle fields. We report on prototyping of a miniature transmitter named MTx+, which is developed for high speed transmission with the dual-channel laser dr…
▽ More
Development of optical links with 850 nm multi-mode vertical-cavity surface-emitting lasers (VCSELs) has advanced to 25 Gbps in speed. For applications in high-energy experiments, the transceivers are required to be tolerant in radiation and particle fields. We report on prototyping of a miniature transmitter named MTx+, which is developed for high speed transmission with the dual-channel laser driver LOCld65 and 850 nm VCSELs packaged in TOSA format. The LOCld65 is fabricated in the TSMC 65 nm process and is packaged in the QFN-40 for assembly. The MTx+ modules and test kits were first made with PCB and components qualified for 10 Gbps applications, and were tested for achieving 14 Gbps. The data transfer rate of the MTx+ module is investigated further for the speed of up to 25 Gbps. The LOCld65 is examined with post-layout simulation and the module design upgraded with components including the TOSA qualified for 25 Gbps applications. The PCB material is replaced by the Panasonic MEGTRON6. The revised MTx+ is tested at 25 Gbps and the eye-diagram shows a mask margin of 22 %.
△ Less
Submitted 21 June, 2020;
originally announced June 2020.
-
Simulating the Chiral Magnetic Wave in a Box System
Authors:
Wen-Hao Zhou,
Jun Xu
Abstract:
The chiral magnetic wave from the interplay between the chiral magnetic effect and the chiral separation effect is simulated in a box system with the periodic boundary condition based on the chiral kinetic equations of motion. Simulation results are compared with available limits from theoretical derivations, and effects of the temperature, the magnetic field, and the specific shear viscosity on t…
▽ More
The chiral magnetic wave from the interplay between the chiral magnetic effect and the chiral separation effect is simulated in a box system with the periodic boundary condition based on the chiral kinetic equations of motion. Simulation results are compared with available limits from theoretical derivations, and effects of the temperature, the magnetic field, and the specific shear viscosity on the key properties of the chiral magnetic wave are discussed. Our study serves as a baseline for further simulations of chiral anomalies in relativistic heavy-ion collisions.
△ Less
Submitted 1 October, 2018;
originally announced October 2018.
-
LOCld65, A Dual-Channel VCSEL Driver ASIC For Detector Front-End Readout
Authors:
Wei Zhou,
Datao Gong,
Quan Sun,
Di Guo,
Guangming Huang,
Kai Jin,
Chonghan Liu,
Jun Liu,
Tiankuan Liu,
Ming Qi,
Xiangming Sun,
James Thomas,
Le Xiao,
Jingbo Ye
Abstract:
We present the design and the test results of a dual-channel Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC LOCld65 for detector front-end readout. LOCld65 is designed in a commercial 65-nm CMOS technology with a power supply of 1.2 V. LOCld65 contains two separate channels with the same structure and the two channels share an I2C slave. Each channel consists of an input amplifier, fou…
▽ More
We present the design and the test results of a dual-channel Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC LOCld65 for detector front-end readout. LOCld65 is designed in a commercial 65-nm CMOS technology with a power supply of 1.2 V. LOCld65 contains two separate channels with the same structure and the two channels share an I2C slave. Each channel consists of an input amplifier, four stages of limiting amplifiers (LAs), a high-current output driver, and a bias-current generator. In order to extend the bandwidth, the input amplifier uses an inductive peaking technique and the LAs use a shared inductive peaking technique. The input amplifier and the output driver each utilize a Continuous-Time Linear Equalizer (CTLE). The LAs employ active feedback. The modulation current, the bias current, the peaking strength of the CTLEs, and the feedback strength of LAs are programmable through an I2C interface. In order to protect from the radiation damage, the I2C slave is implemented with triple modular redundancy. Each channel of LOCld65 is tested to operate up to 14 Gbps with typical power dissipations (the VCSEL included) of 68.3 mW/channel and 62.1 mW/channel at the VCSEL voltages of 3.3 V and 2.5 V, respectively. LOCld65 survives 4.9 kGy(SiO2). LOCld65 is an excellent match for the serializer-deserializer ASIC lpGBT in single- or dual-channel optical transmitters in HL-LHC upgrade applications.
△ Less
Submitted 22 June, 2018;
originally announced June 2018.
-
Development and Characterization of a 3.2 Gb/s Serial Link Transmitter for CMOS Image Sensors in Subatomic Physics Experiments
Authors:
Quan Sun,
Guangyu Zhang,
Datao Gong,
Binwei Deng,
Wei Zhou,
Bihui You,
Le Xiao,
Jian Wang,
Dongxu Yang,
Tiankuan Liu,
Chonghan Liu,
Di Guo,
Jun Liu,
Christine Hu-Guo,
Frederic Morel,
Isabelle Valin,
Xiangming Sun,
Jingbo Ye
Abstract:
This paper presents development and characterization of a 3.2 Gb/s serial link transmitter for CMOS image sensors. The transmitter incorporates Reed-Solomon code to achieve low error rate in the harsh environment of subatomic physics experiments. Pre-emphasis is implemented in the transmitter, allowing data transmission over low-mass cables. It is fabricated in a 0.18 $μm$ CMOS image process as a…
▽ More
This paper presents development and characterization of a 3.2 Gb/s serial link transmitter for CMOS image sensors. The transmitter incorporates Reed-Solomon code to achieve low error rate in the harsh environment of subatomic physics experiments. Pre-emphasis is implemented in the transmitter, allowing data transmission over low-mass cables. It is fabricated in a 0.18 $μm$ CMOS image process as a standalone chip to characterize its performance, with the core area of 1.8 $mm^2$. A frame data rate of $3\cdot10^{-12}$ with a confidence level of 94.5$\%$ was measured through an FPGA based receiver. The measured nominal power consumption is 135 mW. The transmitter functions normally after irradiated with 4.5 Mrad TID.
△ Less
Submitted 18 June, 2018;
originally announced June 2018.
-
Test of \textit{Topmetal-${II}^-$} In Liquid Nitrogen For Cryogenic Temperature TPCs
Authors:
Shuguang Zou,
Yan Fan,
Mangmang An,
Chufeng Chen,
Guangming Huang,
Xiaoting Li,
Jun Liu,
Hua Pei,
Xiangming Sun,
Ping Yang,
Dong Wang,
Le Xiao,
Zhen Wang,
Kai Wang,
Wei Zhou
Abstract:
\textit{Topmetal-${II}^-$} is a highly pixelated direct charge sensor that contains a 72${\times}$72 pixel array of 83$μ$m pitch size. The key feature of \textit{Topmetal-${II}^-$} is that it can directly collect charges via metal nodes of each pixel to form two-dimensional images of charge cloud distributions. \textit{Topmetal-${II}^-$} was proved to measure charged particles without amplificatio…
▽ More
\textit{Topmetal-${II}^-$} is a highly pixelated direct charge sensor that contains a 72${\times}$72 pixel array of 83$μ$m pitch size. The key feature of \textit{Topmetal-${II}^-$} is that it can directly collect charges via metal nodes of each pixel to form two-dimensional images of charge cloud distributions. \textit{Topmetal-${II}^-$} was proved to measure charged particles without amplification at room temperature. To measure its performance at cryogenic temperature, a \textit{Topmetal-${II}^-$} sensor is embedded into a liquid nitrogen dewar. The results presented in this paper show that \textit{Topmetal-${II}^-$} can also operate well at this low temperature with a noise (ENC) of 12 e$^-$ lower than that at room temperature (13 e$^-$). From the noise perspective, \textit{Topmetal-${II}^-$} is a promising candidate for the next generation readout of liquid argon and xenon Time Projection Chamber (TPC) used in experiments searching for neutrinoless double beta decay and dark matter.
△ Less
Submitted 6 June, 2016; v1 submitted 26 January, 2016;
originally announced January 2016.
-
JUNO Conceptual Design Report
Authors:
T. Adam,
F. An,
G. An,
Q. An,
N. Anfimov,
V. Antonelli,
G. Baccolo,
M. Baldoncini,
E. Baussan,
M. Bellato,
L. Bezrukov,
D. Bick,
S. Blyth,
S. Boarin,
A. Brigatti,
T. Brugière,
R. Brugnera,
M. Buizza Avanzini,
J. Busto,
A. Cabrera,
H. Cai,
X. Cai,
A. Cammi,
D. Cao,
G. Cao
, et al. (372 additional authors not shown)
Abstract:
The Jiangmen Underground Neutrino Observatory (JUNO) is proposed to determine the neutrino mass hierarchy using an underground liquid scintillator detector. It is located 53 km away from both Yangjiang and Taishan Nuclear Power Plants in Guangdong, China. The experimental hall, spanning more than 50 meters, is under a granite mountain of over 700 m overburden. Within six years of running, the dete…
▽ More
The Jiangmen Underground Neutrino Observatory (JUNO) is proposed to determine the neutrino mass hierarchy using an underground liquid scintillator detector. It is located 53 km away from both Yangjiang and Taishan Nuclear Power Plants in Guangdong, China. The experimental hall, spanning more than 50 meters, is under a granite mountain of over 700 m overburden. Within six years of running, the detection of reactor antineutrinos can resolve the neutrino mass hierarchy at a confidence level of 3-4$σ$, and determine neutrino oscillation parameters $\sin^2θ_{12}$, $Δm^2_{21}$, and $|Δm^2_{ee}|$ to an accuracy of better than 1%. The JUNO detector can be also used to study terrestrial and extra-terrestrial neutrinos and new physics beyond the Standard Model. The central detector contains 20,000 tons liquid scintillator with an acrylic sphere of 35 m in diameter. $\sim$17,000 508-mm diameter PMTs with high quantum efficiency provide $\sim$75% optical coverage. The current choice of the liquid scintillator is: linear alkyl benzene (LAB) as the solvent, plus PPO as the scintillation fluor and a wavelength-shifter (Bis-MSB). The number of detected photoelectrons per MeV is larger than 1,100 and the energy resolution is expected to be 3% at 1 MeV. The calibration system is designed to deploy multiple sources to cover the entire energy range of reactor antineutrinos, and to achieve a full-volume position coverage inside the detector. The veto system is used for muon detection, muon induced background study and reduction. It consists of a Water Cherenkov detector and a Top Tracker system. The readout system, the detector control system and the offline system insure efficient and stable data acquisition and processing.
△ Less
Submitted 28 September, 2015; v1 submitted 28 August, 2015;
originally announced August 2015.
-
Neutrino Physics with JUNO
Authors:
Fengpeng An,
Guangpeng An,
Qi An,
Vito Antonelli,
Eric Baussan,
John Beacom,
Leonid Bezrukov,
Simon Blyth,
Riccardo Brugnera,
Margherita Buizza Avanzini,
Jose Busto,
Anatael Cabrera,
Hao Cai,
Xiao Cai,
Antonio Cammi,
Guofu Cao,
Jun Cao,
Yun Chang,
Shaomin Chen,
Shenjian Chen,
Yixue Chen,
Davide Chiesa,
Massimiliano Clemenza,
Barbara Clerbaux,
Janet Conrad
, et al. (203 additional authors not shown)
Abstract:
The Jiangmen Underground Neutrino Observatory (JUNO), a 20 kton multi-purpose underground liquid scintillator detector, was proposed with the determination of the neutrino mass hierarchy as a primary physics goal. It is also capable of observing neutrinos from terrestrial and extra-terrestrial sources, including supernova burst neutrinos, diffuse supernova neutrino background, geoneutrinos, atmosp…
▽ More
The Jiangmen Underground Neutrino Observatory (JUNO), a 20 kton multi-purpose underground liquid scintillator detector, was proposed with the determination of the neutrino mass hierarchy as a primary physics goal. It is also capable of observing neutrinos from terrestrial and extra-terrestrial sources, including supernova burst neutrinos, diffuse supernova neutrino background, geoneutrinos, atmospheric neutrinos, solar neutrinos, as well as exotic searches such as nucleon decays, dark matter, sterile neutrinos, etc. We present the physics motivations and the anticipated performance of the JUNO detector for various proposed measurements. By detecting reactor antineutrinos from two power plants at 53-km distance, JUNO will determine the neutrino mass hierarchy at a 3-4 sigma significance with six years of running. The measurement of antineutrino spectrum will also lead to the precise determination of three out of the six oscillation parameters to an accuracy of better than 1\%. Neutrino burst from a typical core-collapse supernova at 10 kpc would lead to ~5000 inverse-beta-decay events and ~2000 all-flavor neutrino-proton elastic scattering events in JUNO. Detection of DSNB would provide valuable information on the cosmic star-formation rate and the average core-collapsed neutrino energy spectrum. Geo-neutrinos can be detected in JUNO with a rate of ~400 events per year, significantly improving the statistics of existing geoneutrino samples. The JUNO detector is sensitive to several exotic searches, e.g. proton decay via the $p\to K^++\barν$ decay channel. The JUNO detector will provide a unique facility to address many outstanding crucial questions in particle and astrophysics. It holds the great potential for further advancing our quest to understanding the fundamental properties of neutrinos, one of the building blocks of our Universe.
△ Less
Submitted 18 October, 2015; v1 submitted 20 July, 2015;
originally announced July 2015.
-
K*0 production in Cu+Cu and Au+Au collisions at \sqrt{s_NN} = 62.4 GeV and 200 GeV
Authors:
M. M. Aggarwal,
Z. Ahammed,
A. V. Alakhverdyants,
I. Alekseev,
J. Alford,
B. D. Anderson,
Daniel Anson,
D. Arkhipkin,
G. S. Averichev,
J. Balewski,
L. S. Barnby,
S. Baumgart,
D. R. Beavis,
R. Bellwied,
M. J. Betancourt,
R. R. Betts,
A. Bhasin,
A. K. Bhati,
H. Bichsel,
J. Bielcik,
J. Bielcikova,
B. Biritz,
L. C. Bland,
B. E. Bonner,
W. Borowski
, et al. (362 additional authors not shown)
Abstract:
We report on K*0 production at mid-rapidity in Au+Au and Cu+Cu collisions at \sqrt{s_{NN}} = 62.4 and 200 GeV collected by the Solenoid Tracker at RHIC (STAR) detector. The K*0 is reconstructed via the hadronic decays K*0 \to K+ pi- and \bar{K*0} \to K-pi+. Transverse momentum, pT, spectra are measured over a range of pT extending from 0.2 GeV/c to 5 GeV/c. The center of mass energy and system siz…
▽ More
We report on K*0 production at mid-rapidity in Au+Au and Cu+Cu collisions at \sqrt{s_{NN}} = 62.4 and 200 GeV collected by the Solenoid Tracker at RHIC (STAR) detector. The K*0 is reconstructed via the hadronic decays K*0 \to K+ pi- and \bar{K*0} \to K-pi+. Transverse momentum, pT, spectra are measured over a range of pT extending from 0.2 GeV/c to 5 GeV/c. The center of mass energy and system size dependence of the rapidity density, dN/dy, and the average transverse momentum, <pT>, are presented. The measured N(K*0)/N(K) and N(φ)/N(K*0) ratios favor the dominance of re-scattering of decay daughters of K*0 over the hadronic regeneration for the K*0 production. In the intermediate pT region (2.0 < pT < 4.0 GeV/c), the elliptic flow parameter, v2, and the nuclear modification factor, RCP, agree with the expectations from the quark coalescence model of particle production.
△ Less
Submitted 10 June, 2010;
originally announced June 2010.
-
Higher Moments of Net-proton Multiplicity Distributions at RHIC
Authors:
M. M. Aggarwal,
Z. Ahammed,
A. V. Alakhverdyants,
I. Alekseev,
J. Alford,
B. D. Anderson,
D. Arkhipkin,
G. S. Averichev,
J. Balewski,
L. S. Barnby,
S. Baumgart,
D. R. Beavis,
R. Bellwied,
M. J. Betancourt,
R. R. Betts,
A. Bhasin,
A. K. Bhati,
H. Bichsel,
J. Bielcik,
J. Bielcikova,
B. Biritz,
L. C. Bland,
3 B. E. Bonner,
J. Bouchet,
E. Braidot
, et al. (359 additional authors not shown)
Abstract:
We report the first measurements of the kurtosis (κ), skewness (S) and variance (σ^2) of net-proton multiplicity (N_p - N_pbar) distributions at midrapidity for Au+Au collisions at \sqrt(s_NN) = 19.6, 62.4, and 200 GeV corresponding to baryon chemical potentials (μ_B) between 200 - 20 MeV. Our measurements of the products κσ^2 and S σ, which can be related to theoretical calculations sensitive t…
▽ More
We report the first measurements of the kurtosis (κ), skewness (S) and variance (σ^2) of net-proton multiplicity (N_p - N_pbar) distributions at midrapidity for Au+Au collisions at \sqrt(s_NN) = 19.6, 62.4, and 200 GeV corresponding to baryon chemical potentials (μ_B) between 200 - 20 MeV. Our measurements of the products κσ^2 and S σ, which can be related to theoretical calculations sensitive to baryon number susceptibilities and long range correlations, are constant as functions of collision centrality. We compare these products with results from lattice QCD and various models without a critical point and study the \sqrt(s_NN) dependence of κσ^2. From the measurements at the three beam energies, we find no evidence for a critical point in the QCD phase diagram for μ_B below 200 MeV.
△ Less
Submitted 12 June, 2010; v1 submitted 28 April, 2010;
originally announced April 2010.
